INSTRUCTION MANUAL
Vanguard-HD Mega pixel
IR OUTDOOR CAMERA
CONTENTS
WARNING & CAUTION
GENERAL FEATURES
NAME OF EACH PART
INSTALLATION
CONNECTION
SPECIFICATIONS
OSD MENU SETTING
TROUBLESHOOTING
DIMENSIONS
2
4
5
7
11
12
14
16
17
1
WARNING & CAUTION
If you fail to read this information and handle the product incorrectly, death or serious injury may occur.
The unit should be installed by the trained Personnel.
Switch off immediately if the product emits smoke or abnormal heat.
Never install the product in area exposed to oil or gas.
Never touch the power cord with wet hands.
Clean only with dry cloth.
Ensure that the product is not subjected to strong impacts and vibration.
Never expose the camera to direct sunlight
WARNING
Never disassemble the unit by unauthorized person.
Serious and Permanent damage will occur.
2
WARNING & CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
3
LABEL
4. SCREW M4x20
5. CALBLOCK 6x30
6. SCREW 4x30
7. CAP SCREW
4EA
4EA
4EA
2EA
GENERAL FEATURES
*
*
*
*
*
*
*
*
*
1/3" Panasonic 2.2M Progressive Scan CMOS
HD-SDI : 1080@30p/25p, 720@60p/50p
NTSC, PAL CVBS without WDR
TDN ICR Mega pixel lens
40PCS High performance IR LEDs
Joystick type OSD control key
Wide Dynamic Range compensation
Adaptive Contrast Enhancer
Supports various digital features of Mirror, Flip, Digital Zoom,
Privacy Masking, Motion Detection, Sharpness control and shading
*
*
*
*
*
*
IP-67 rated waterproof frame housing
3-Axis bracket (Wall, Ceiling, Pole mount available)
Easy installation by hinge type junction box (option)
Adjustable Zoom & Focus of the lens externally
Adjustable Day & Night lux level value
Fan & Heater (option)
4
NAME OF EACH PART
1. Sunvisor
2. Camera Body
3. Function Cover
4. Function Part
5. IR LED Lamp
6. Lens
7. Camera Bracket
8. Lens Control Lever
9. Set Screw groove for Sunvisor
10. X-Axis Set Screw
11. Y-Axis Set Screw
12. Z-Axis Set Screw
5
FIG.1
NAME OF EACH PART
FUNCTION PART
FIG.2
1
2
3
4
5
Extra Video Out
IR Gain
3 Lux / 6 Lux
ON / OFF
OSD Button
FUNCTION
CVBS Output
IR Gain Control
CDS Sensitivity Control
IR LED ON / OFF
Up, Down, Set, Left, Right
6
INSTALLATION
Template Label
6mm
Calblock( 6x30)
FIG.3
81mm
Hole Diameter : 6mm
Depth : 30mm
FIG.4
Seal Tape
FIG.5
1. When you need to install a camera on the surface of a concrete wall, you can drill a hole like Fig.3 exactly by using a Template Card offered by accessory.
2. As Fig.4, please set a Calblock in the hole of the wall.
3. After connect a Power Jack and Video Connector. Please wrap and tighten by using a seal tape (water-proof tape) to prevent a leak of water.
7
INSTALLATION
Screw 4x30
FIG.6
Wrench 2mm
Wrench 3mm
FIG.7
FIG.8
4. Like Fig.6, after put the cable connector part into the bracket, please fix the bracket on the wall by use of screws.
5. Like Fig.7, after set the camera to desired direction, please fix tightly by L-Wrench.
6. After finish adjustment of OSD function, please tighten the screw tightly to prevent a leak of water close the cover then. (Fig.8)
8
INSTALLATION
How to install Junction Box
Template Label
6mm
Calblock( 6x30)
FIG.9
46mm
Screw 4x30
Hole Diameter : 6mm
Depth : 30mm
FIG.10
FIG.11
1. Like Fig.9, please make a screw sign hole on the wall for fixation of Junction Box by use of offered Template Label.
2. As Fig.10, please set a Calblock in the hole of the wall.
3. Then stick by screw by using a Junction Box on the surface of a wall.
9
INSTALLATION
Screw M4x60
Nut M4
FIG.12
FIG.13
4. Joint the Camera bracket to the Junction Box, then put the Screw into a Hinge part after that tighten by Nut. (Fig.12)
5. Connect a cable and like Fig.13, please join Bracket part.
(Please refer to Page 11 regarding cable connection)
How to install Ceiling & Pole
Screw M4x20
Pole Mount Bracket
(option)
FIG.14
1. In case of installation on Ceiling or Pole, please refer to Fig.14 & Fig.15.
FIG.15
10
CONNECTION
DUAL POWER TYPE
*A power source connection is nonpolar.
FIG.16
1. Terminal Block (Accessory)
2. DC Jack Cable (Accessory)
3. Adaptor (DC12V or AC24V)
4. Video Output (HD-SDI)
5. Seal Tape
DC12V POWER TYPE
*A power source connection is nonpolar.
FIG.17
1. DC Jack
2. Adaptor (DC12V)
3. Video Output (HD-SDI)
4. Seal Tape
CAUTION : After connecting the cable, please make sure bind by using a
Seal Tape to prevent a leak of water.
11
SPECIFICATIONS
MODEL
CAMERA
SYSTEM
VIDEO
OSD
EXPOSURE
WHITE
BALANCE
WDR / BLC
/ ACE
DNR
On Screen Display
Language
BRIGHTNESS
AGC
SHUTTER MODE
SHUTTER SPEED
SENS-UP
MODE
MANUAL MODE
MODE
BLC POS X, Y
BLC SIZE X, Y
Full HD Mega Pixel IR Outdoor Camera
TV System
Image Device
Scanning System
Total Pixels
Effective Pixels
Lens
Day & Night System
Min. Illumination
SDI FORMAT
SDI FPS
CVBS SCALE
CVBS OUT
Sync System
Electronic Shutter
Output 1
Output 2
Resolution & frame rate
NTSC (50Hz) / PAL (60Hz)
1/3'' Panasonic CMOS
Progressive Scan
2010(H) X 1108(V) : 2.2Mega pixel
1944(H) X 1092(V) : 2.1Mega pixel
2.8-12mm Mega Pixel Lens
ICR (Mechanism Filter Mountable)
0.1 lux @ F1.4, 30IRE
1080P / 720P
30/25@1080p, 60/50@720p
FULL / CUT
OFF / ON
Internal
60Hz :1/30~1/30,000sec, 50Hz : 1/25~1/30,000sec
1 HD-SDI
CVBS (NTSC, PAL) without WDR
Digital : 1080@30p/25p, 720@60p/50p
Analog : 700TVL
Bulit-in
English
0~20
0~20
AUTO / MANUAL
1/30(25),60(50),120(100), 250, 700, 1K, 1.6K, 5K, 7K, 10K, 30K
OFF / X2 / X3 / X4
AUTO / PUSH LOCK / MANUAL
COLOR TEMP. / RED GAIN / BLUE GAIN
OFF / WDR / BLC / ACE
0~20
0~20
OFF / LOW / MIDDLE / HIGH
12
SPECIFICATIONS
MODEL
DAY &
NIGHT
IMAGE
SPECIAL
POWER &
ENVIRON-
MENTAL
MODE
DWELL TIME
D->N LEVEL
N->D LEVEL
SHARPNESS
COLOR LEVEL
MIRROR
FLIP
LENS SHADING
D-ZOOM
COMM ADJUST
PRIVACY
HLM
SMART IR
MOTION
Full HD Mega Pixel IR Outdoor Camera
AUTO / EXT / COLOR / B&W
1~10sec
0~20
0~20
0~20
0~20
OFF / ON
OFF / ON
OFF / ON
1~40X
CAM ID / BAUD RATE / 485 TERM.
OFF / ON (position, size, color adjustable)
OFF / ON (level, color adjustable)
ON / OFF
OFF / ON (sensitivity adjustable)
OPERATING TEMP./ HUM.
30%~80% RH
STORAGE TEMP./ HUM.
o o
-20 C~+60 C / 20%~90% RH
POWER
POWER CONSUMPTION
IR LED
DIMENSION
WEIGHT
DC type (Max. 6.5W) /
Dual Type (DC:Max. 7W, AC:Max. 9W)
DC type (Max. 450mA) /
Dual Type (DC:Max. 500mA, AC:Max. 350mA)
Round 40pcs (30deg)
98mm(W) X 88.5mm(H) X 149mm(L)
1.1 Kg
13
OSD MENU SETTING
SETUP MENU
LENS
EXPOSURE
WHITE BALANCE
WDR/BLC/ACE
DC
SUB MANU 1
MANUAL
BRIGHTNESS
AGC
SHUTTER MODE
SHUTTER SPEED
SENS-UP
MODE
COLOR TEMP.
RED GAIN
BLUE GAIN
PUSH AUTO
MODE
BLC POS-X
BLC POS-Y
BLC SIZ-X
BLC SIZ-Y
DNR
DAY&NIGHT
IMAGE
MODE
SENSOR
DWELL TIME
D->N LEVEL
N->D LEVEL
SHARPNESS
COLOR LEVEL
MIRROR
FLIP
LENS SHADING
GAMMA
D-ZOOM
SPECIAL
COMM ADJUST
PRIVACY
HLM
MOTION
SUB MANU 2
CAM ID
BAUDRATE
485 TERM.
OFF
MASK SEL.
MASK MODE
X-POSITION
Y-POSITION
X-SIZE
Y-SIZE
MASK COLOR
OFF
HLM LEVEL
HLM COLOR
OFF
SENSITIVITY
VALUE
-
OUTDOOR / INDOOR
0 ~ 20
0 ~ 20
AUTO / MANUAL
1/30(25), 60(50), 120(100), 250, 700, 1K, 1.6K, 5K, 7K, 10K, 30K
OFF / X2 / X3 / X4
AWB / ATW / PUSH LOCK / MANUAL
LOW / MIDDLE / HIGH
0~20
0~20
Press LEFT or RIGHT key
OFF / WDR / BLC / ACE
0~20
0~20
0~20
0~20
OFF / LOW / MIDDLE / HIGH
AUTO / EXT / COLOR / B&W
AGC / CDS
1~10sec, 1sec / step
11(bright) ~ 20(dark)
0(bright) ~ 10(dark)
0~20
0~20
OFF / ON
OFF / ON
OFF / ON
0~4
1,2,4,6,8,12,14,16,18,20,22,24,26,28,30,32,34,36,38,40X
0~255
2400,4800,9600,19200,38400,57600,115200
OFF / ON
*NOTE 1
*NOTE 2
*NOTE 3
*NOTE 1
*Factory setting
0~29
OFF / ON
0~60
0~40
0~40
0~40
BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU
0~20
BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU
0~20
14
OSD MENU SETTING
SETUP MENU
SYSTEM
FACTORY DEFAULT
RETURN
EXIT
SUB MANU 1
SDI FORMAT
SDI FPS
FREQ (NT/PAL)
CVBS SCALE
CVBS OUT
SUB MANU 2 VALUE
1080P / 720P
30/25@1080p, 60/50@720p
60Hz(NTSC) / 50Hz(PAL)
FULL / CUT
OFF / ON
Reset to factory setting
Return to previous menu
Exit SETUP menu
*Factory setting
*NOTE 4
*NOTE 1
*NOTE 1; WDR is not operated at 'SHUTTER MODE=MANUAL'.CVBS OUT is OFF at WDR mode.
With WDR mode, the frame speed is decreased from 30fps to 15fps(or from 60fps to 30fps)
*NOTE 2; OSD Button action is delayed while SENS-UP operation is performed.
Press the button more than 1 sec.
*NOTE 3; AWB operation is performed while the button is pressed and shifts to hold mode when the button is released.
*NOTE 4; Factory default 60Hz
15
TROUBLESHOOTING
PROBLEM
No picture
Camera with excessive heat, Abnormal motion or Black lines on the screen.
Blinking Screen
SOLUTION
Check if the power cable is connected properly.
Check if the video cable is connected correctly.
Check if the power supply meets the minimum requirements and that the power supply is functioning properly.
Unclear Screen
No operation of Color
Auto mode
No operation of
Motion Detection
Inaccurate Color
Check if the Camera faces the Sun or fluorescent lamp.
Check if the Auto Iris Lens connector is connected properly.
Check if the Lens is dirty. If necessary, clean the lens with a soft cloth or lens brush.
Check the camera positioning and setting.
Adjust the camera position if too much light is entering the iris.
Check the Back-Focus Setting.
Check if you set 'Color' mode 'EXT/ON/OFF'
Check if you set 'Gain' mode off.
Check if 'Motion Detection' mode is on
Check if the 'MD Level' is set too low.
Check if the 'MD Area' is set properly.
Insure that 'White Balance' is set properly.
16
DIMENSIONS
17
UNITS:mm
MP86C028
