SWA1801

z

SYSTEM USER’S MAnUAl

ACTIVE

LIMIT SIGNAL

PARALLEL

THRU

(FULL RANGE OUTPUT)

FULL RANGE

INPUT

THERMAL POWER

L

SUBWOOFER

CONTROL

NORMAL

HIGH PASS

(MID/HIGH FREQ)

OUTPUT

120Hz

L

IN

R

SUBWOOFER

LEVEL

NORMAL

REV 180

PHASE

OUT

R

POWER

SWA1801z

ACTIVE SUBWOOFER

60Hz-115V-AC FUSE AC125V-T8AL

©2005 LOUD TECHNOLOGIES INC.

LOUD TECHNOLOGIES INC.: • PATENT PENDING

CAUTION

WARNING:

THIS SURFACE MAY REACH HIGH TEMPERATURE DURING

OF CLEARANCE FROM THIS SURFACE AND ADEQUATE VENTILATION. TO REDUCE

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THIS PANEL OR ANY ATTACHED

COMPONENT. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED PERSONNEL. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

AVIS:

RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

SERIAL NUMBER MANUFACTURING DATE

ON

SAFETY InSTRUCTIOnS

1.

Read Instructions — All the safety and operation instructions should be read before this Mackie product is operated.

2.

Retain Instructions — The safety and operating instructions should be kept for future reference.

3.

Heed Warnings — All warnings on this Mackie product and in these operating instructions should be followed.

4.

Follow Instructions — All operating and other instructions should be followed.

5.

Water and Moisture — This Mackie product should not be used near water

– for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, swamp or salivating St. Bernard dog, etc.

6.

Cleaning — Clean only with a dry cloth.

7.

Ventilation — This Mackie product should be situated so that its location or position does not interfere with its proper ventilation. For example, the Component should not be situated on a bed, sofa, rug, or similar surface that may block any ventilation openings, or placed in a built-in installation such as a bookcase or cabinet that may impede the flow of air through ventilation openings.

8.

Heat — This Mackie product should be situated away from heat sources such as radiators, or other devices which produce heat.

WARnInG:

The heat sink may reach high temperatures during standard use.

To ensure proper operation, allow a minimum of six inches of clearance from the heat sink surface and adequate ventilation.

9.

Power Sources — This Mackie product should be connected to a power supply only of the type described in these operation instructions or as marked on this Mackie product.

10.

Power Cord Protection — Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit this Mackie product.

11.

Object and Liquid Entry — Care should be taken so that objects do not fall on, and liquids are not spilled into, this Mackie product.

12.

Damage Requiring Service — This Mackie product should be serviced only by qualified service personnel when:

A.

The power-supply cord or the plug has been damaged; or

B.

Objects have fallen, or liquid has spilled into this Mackie product; or

C.

This Mackie product has been exposed to rain; or

D.

This Mackie product does not appear to operate normally or exhibits a marked change in performance; or

E.

This Mackie product has been dropped, or its chassis damaged.

13.

Servicing — The user should not attempt to service this Mackie product beyond those means described in this operating manual. All other servicing should be referred to the Mackie Service Department.

14.

To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

Pour prévenir les chocs électriques ne pas utiliser cette fiche polariseé avec un prolongateur, un prise de courant ou une autre sortie de courant, sauf si les lames peuvent être insérées à fond sans laisser aucune pariie à découvert.

15.

Grounding or Polarization — Precautions should be taken so that the grounding or polarization means of this Mackie product is not defeated.

16.

Power Precaution — Unplug this Mackie product during lightning storms or when unused for long periods of time. Note that this Mackie product is not completely disconnected from the AC mains service when the power switch is in the OFF position.

17.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help

.

CAUTION: Changes or modifications to this device not expressly approved by

LOUD Technologies Inc. could void the user’s authority to operate the equipment under FCC rules.

18.

This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.

ATTENTION —Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant las limites applicables aux appareils numériques de class A/de class B (selon le cas) prescrites dans le règlement sur le brouillage radioélectrique édicté par les ministere des communications du Canada.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN

WARNING — To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL

WARnInG

— The cabinet has no rigging points and is not suitable for flying. Never attempt to suspend the cabinet by its handles.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.

2

The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Correct Disposal of this product:

This symbol indicates that this product should not be disposed of with your household waste, according to the WEEE Directive

(2002/96/EC) and your national law. This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service.

Lend Me Your Ears

Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a period of time. The U.S. Government’s Occupational Safety and

Health Administration (OSHA) has specified the permissible noise level exposures shown in this chart.

According to OSHA, any exposure in excess of these permissible limits could result in some hearing loss. To ensure against potentially dangerous exposure to high sound-pressure levels, it is recommend ed that all persons exposed to equipment capable of producing these levels use hearing protectors while this unit is in operation. Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure is in excess of the limits set forth here.

Duration, per day in hours

Sound Level dBA,

Slow Response

4

3

8

6

2

1.5

1

0.5

0.25 or less 115

90

92

95

97

100

102

105

110

Typical Example

Duo in small club

Subway Train

Very loud classical music

Fooyoung screaming at desTROYer about deadlines

Loudest parts at a rock concert

CONTENTS

Lend Me Your Ears ...........................................................3

INTRODUCTION ...............................................................3

REAR PANEL DESCRIPTION ...........................................4

HOOKUP DIAGRAMS ......................................................5

CONNECTIONS ................................................................6

PLACEMENT .....................................................................6

AC POWER ......................................................................7

THERMAL CONSIDERATIONS ........................................7

SERVICE INFORMATION .................................................7

Troubleshooting ........................................................7

Repair ........................................................................9

SWA1801z SPECIFICATIONS .......................................10

SWA1801z LIMITED WARRANTY..................................11

The SWA1801z can produce a maximum

SPL of 135 dB @ 1m

INTRODUCTION

Thank you for choosing Mackie’s active sound reinforcement speaker systems.

The SWA1801z is a high-output active subwoofer system. It features a high-precision 18" transducer combined with application-specific amplifier technology. The system is composed of a single, compact subwoofer cabinet with built-in control and amplifier electronics.

Connecting and setting up the SWA1801z is a breeze. It accepts a stereo or mono line-level signal via female XLR input jacks. Male XLR Thru jacks are provided for daisy-chaining the signal to additional

SWA1801z cabinets. The built-in crossover separates the low frequencies from the high frequencies, and routes the high frequencies to the male XLR high-pass output jacks. Connect these to the inputs of full-range active speakers such as the Mackie SA1521z, or to an amplifier powering a pair of passive speakers such as a combination of the Mackie M•1400i and C300z. A Phase switch gives you the option of reversing the polarity of the signal to the subwoofer by 180º. A Subwoofer Level control allows you to adjust the balance between the subwoofer and the full-range speakers.

The built-in amplifier produces 800 watts of continuous power. The amplifier module sits on a heatsink that eliminates the need for fans, dramatically extending life expectancy, and eliminating maintenance cycles. A tremendous benefit of having the amplifier located within the subwoofer cabinet is that the SWA1801z functions as a system, optimizing acoustic, electronic, and mechanical designs to achieve the highest level of performance and value.

The cabinet is constructed with 15 mm thick multilayered birch plywood. Carrying handles are integrated into each side for easy loading, and casters are attached to the rear for easy transport.

Don’t forget to visit our website at www.mackie.com

for more information about this and other Mackie products.

Part No. SW0619 Rev. C 03/12

©2005-2012 LOUD Technologies Inc. All Rights Reserved.

3

R

REAR PANEL DESCRIPTION

POWER Switch

Use this switch to turn the SWA1801z on and off. Make sure the signal source’s level control is turned down before you turn it on.

AC Receptacle

This is where you connect the AC linecord to provide AC power to the SWA1801z’s built-in power amplifiers. Plug the linecord into an AC socket properly configured for your particular model.

LIMIT Indicator

The SWA1801z has a built-in limiter that prevents the amplifier outputs from overdriving the transducers. The LIMIT indicator lights when the limiter is activated. It’s okay for the LIMIT indicator to blink occasionally, but if it blinks frequently or lights continuously, turn down the level control until the LIMIT indicator only blinks occasionally.

SIGNAL Present Indicator

This LED illuminates whenever there is a signal present at the FULL RANGE INPUT connector on the rear panel.

THERMAL Indicator

The SWA1801z has a thermal protection circuit that monitors the internal temperature of the amplifiers and heatsink. If the internal temperature should exceed a safe operating level, this indicator lights and the signal is muted to allow the amplifier to cool. When the temperature cools to a safe level once again, the thermal protection circuit deactivates and normal operation resumes.

Note:

Activation of the thermal protection circuit is an indication that you should take steps to avoid continued thermal problems. See “Thermal

Considerations” on page 7.

POWER Indicator

When the POWER switch is turned on and the linecord is connected to an active AC power supply, this indicator lights green to let you know that you’re ready to rock and roll. The cool blue

LED on the front of the cabinet works in the same way.

FULL RANGE INPUT

These are female XLR-type connectors that accept a balanced line-level signal from a mixing console or other signal source.

THRU (FULL RANGE OUTPUT)

These are male XLR-type connectors that produce exactly the same signal that is connected to the FULL RANGE INPUT jack. Use it to daisychain several SWA1801z's together off the same signal source.

HIGH PASS (MID/HIGH FREQ) OUTPUT

These are male XLR-type connectors that produce the frequencies above 120Hz. Connect these to a pair of full-range active speakers or to an amplifer/passive speaker combination. The

SWA1801z reproduces the frequencies below

120Hz.

SUBWOOFER LEVEL Control

This adjusts the subwoofer level. The center detent position provides 15 dB of headroom with a nominal +4 dBu input signal. Use this as a starting point for setting the balance between the subwoofer and the main speakers.

PHASE

This switch reverses the polarity of the subwoofer output. Depending on the placement of the SWA1801z subwoofer relative to the full-range speakers, you may get a better low-frequency response in the room if you reverse the polarity of the subwoofer’s signal. Experiment with this switch to determine which position sounds best.

4

POWER

SWA1801z

ACTIVE SUBWOOFER

60Hz-115V-AC FUSE AC125V-T8AL

DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA

©2005 LOUD TECHNOLOGIES INC.

"MACKIE" AND THE "RUNNING MAN" FIGURE ARE REGISTERED TRADEMARKS OF

LOUD TECHNOLOGIES INC.: • PATENT PENDING

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

THIS SURFACE MAY REACH HIGH TEMPERATURE DURING

STANDARD USE. TO ENSURE PROPER OPERATION ALLOW A MINIMUM OF 6 INS.

OF CLEARANCE FROM THIS SURFACE AND ADEQUATE VENTILATION. TO REDUCE

THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THIS PANEL OR ANY ATTACHED

COMPONENT. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO

REPLACE WITH THE SAME TYPE FUSE AND RATING.

DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE

AVIS:

RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.

DEBRANCHER AVANT DE REMPLACER LE FUSIBLE

SERIAL NUMBER

MANUFACTURING DATE

ON

LIMIT

PARALLEL

SIGNAL

IN

THERMAL POWER

L

SUBWOOFER

CONTROL

NORMAL

(+4dBu )

HIGH PASS

(MID/HIGH FREQ)

OUTPUT

120Hz

L

O O

+15

SUBWOOFER

REV 180

PHASE

R

R

OUT

NORMAL

HOOKUP DIAGRAMS

SA1521z

Plays the Mid and

High Frequencies

SA1521z

Plays the Mid and

High Frequencies

C300z

Plays the Mid and

High Frequencies

C300z

Plays the Mid and

High Frequencies

Line-Level

Mid/High

Out Left

Pole

Mount

ACTIVE

Power

Cord

Line-Level

Mid/High

Out Right

Pole

Mount

ACTIVE

Power

Cord

Pole

Mount

ACTIVE

Power

Amplifier

Line-Level

Hi-Pass Out

Full

Range

Full

Range

ACTIVE

Pole

Mount

Full

Range

Left

Full

Range

Right

1202-VLZ

PRO

SWA1801z

Plays the Low

Frequencies

Power

Cords

SWA1801z

Plays the Low

Frequencies

Power

Cords

2 SWA1801 z

S

WITh 2 SA1521 z

S

SWA1801z

Plays the Low

Frequencies

Power

Cord

SWA1801z

Plays the Low

Frequencies

Power

Cord

2 SWA1801 z

S

WITh STEREO AMPlIFIER AnD 2 C300 z

S

Line-Level

Hi-Pass

Out L

SRM450

Plays the Mid and

High Frequencies

Power

Cord

1 SWA1801 z

Full

Range

Full

Range

1202-VLZ

PRO

ACTIVE

SWA1801z

Plays the Low

Frequencies

Power

Cord

SRM450

Plays the Mid and

High Frequencies

Line-Level

Hi-Pass

Out R

Power

Cord

WITh 2 SRM450

S

C300z

Plays the Mid and

High Frequencies

Full

Range

Full

Range

1202-VLZ

PRO

SWA1801z

Plays the Low

Frequencies

ACTIVE

C300z

Plays the Mid and

High Frequencies

Power

Cord

Line-Level

Hi-Pass Out

Stereo Power

Amplifier

Power

Cord

1 SWA1801 z

WITh STEREO AMPlIFIER AnD 2 C300 z

S

5

CONNECTIONS

The SWA1801z has two female XLR inputs that accept a balanced line-level signal. When connecting a balanced signal, be sure it’s wired per AES

(Audio Engineering Society) standards:

Hot (+)

XLR

Cold (–)

Shield (Ground)

Pin 2

Pin 3

Pin 1

Simply plug the signal source (i.e., mixer output) into the first speaker’s FULL RANGE INPUT jacks, and patch that speaker’s THRU jacks to the next speaker’s INPUT jacks, and so on, daisychaining multiple speakers.

The THRU jack is wired straight from the

FULL RANGE INPUT connector — there is no electronic circuitry between — so the signal coming out of the THRU jack is exactly the same as the signal going in.

The HIGH PASS OUTPUT jacks provide a line-level signal of the frequencies above 120Hz that you connect to a pair of active speakers (or to a stereo amplifier powering a pair of passive speakers).

Balanced XLR Connectors

PLACEMENT

The SWA1801z subwoofer is designed to sit on the floor. A socket is provided on the top of the

SWA1801z for mounting the Mackie SA1521z or

SRM450 active speakers. Use the optional Mackie speaker mounting pole (SPM100) to mount them on the SWA1801z (see Hookup Diagram on page

5).

If connecting an unbalanced signal to the

SWA1801z balanced input, be sure that the signal high (hot) connection is wired to Pin 2 and the unbalanced ground connection is wired to the low

and

the ground connections of the balanced input (Pins 3 and 1). If there are ground-loop problems, try connecting the unbalanced ground connection only to the input low connection (Pin

3), and leaving the input ground connection disconnected.

There are also four male XLR connectors labeled THRU (FULL RANGE OUTPUT) and HIGH

PASS (MID/HIGH FREQ) OUTPUT . These are also wired according to the AES standard.

The THRU output connectors allow you to connect more than one SWA1801z to your system.

As with any powered components, protect the

SWA1801z from exposure to moisture. If you are setting them up outdoors, make sure they are under cover if you expect rain.

WARNING

: The cabinet has no rigging points and is not suitable for rigging.

NEVER

attempt to suspend the SWA1801z by its handles.

Unbalanced Male XLR Connector

6

AC POWER

Be sure the SWA1801z is plugged into an outlet that is able to supply the correct voltage specified for your model. If the voltage should drop below 97% of the specified line voltage, the built-in amplifiers will no longer be able to supply rated power. (They will continue to operate down to 80% of the rated line voltage, but won’t reach full power, resulting in lower headroom.)

Be sure the electrical service can supply enough amperage for all the components connected to it.

We recommend that a stiff (robust) supply of

AC power be used because the amplifiers place high current demands on the AC line. The more power that is available on the line, the louder the speakers will play and the more peak output power will be available for cleaner, punchier bass.

A suspected problem of “poor bass performance” is often caused by a weak AC supply to the amplifiers.

Never remove the ground pin on the power cord of the SWA1801z or any other component. This is very dangerous.

THERMAL

CONSIDERATIONS

The SWA1801z has a powerful 800 watt amplifier built-in. As amplifiers produce heat, it is important to dissipate the heat as quickly as possible. This results in increased reliability and longevity for the amplifier.

The amplifier module is mounted on a large heatsink, which is cooled by convection where cool air is drawn through it’s fins, carrying the heat away. In order for this convection cooling to work efficiently, it is important to provide adequate airspace behind the loudspeaker. When you position the SWA1801z, we recommend leaving at least six inches of air space behind it.

In the unlikely event of the amplifier overheating, a built-in thermal switch will activate, which mutes the signal. When the amplifier has cooled down to a safe operating temperature, the thermal switch resets itself, and the SWA1801z resumes normal operation.

If the thermal switch activates frequently, try turning down the level control a notch or two on the mixing console (or other signal source) or on the subwoofer itself to avoid overheating the amplifiers.

If the temperature in the room is too high, it could cause the amplifier to overheat. In this case, you should try aiming a fan at the rear panel to move more air across the heatsink panel.

7

8

SERVICE INFORMATION

If you think your Mackie product has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website

(www.mackie.com/support) where you will find lots of useful information such as FAQs, documentation, and user forums. You may find the answer to the problem without having to send your Mackie product away.:

Troubleshooting

Poor bass performance

• Check the polarity of the connections between the mixer and the loudspeakers.

You may have your positive and negative connections reversed at one end of one cable, causing one loudspeaker to be out-of-phase.

• Try switching the PHASE switch on the rear panel. This affects the polarity between the full-range speakers and the SWA1801z and may improve the low-frequency response.

No power

• Our favorite question: Is it plugged in? Make sure the AC outlet is live (check with a tester or lamp).

• Our next favorite question: Is the POWER switch on? If not, try turning it on.

• Is the POWER LED on the rear panel glowing green? If not, make sure the AC outlet is live.

If so, refer to “No sound” next.

• The internal AC line fuse may be blown. This is not a user serviceable part. If you suspect the AC line fuse is blown, please see the

“Repair” section on page 9.

No sound

• Is the input

LEVEL

control for the input source or the subwoofer turned all the way down? Verify that all the volume controls in the system are properly adjusted.

• Is the signal source working (and making union scale)? Make sure the connecting cables are in good repair and securely connected at both ends. Make sure the output volume (gain) control on the mixing console is turned up sufficiently to drive the inputs of the speaker.

• Make sure the mixer does not have a Mute on or a Processor loop engaged. If you find something like this, make sure the volume/ gain is turned down before disengaging the offending switch.

• Is the thermal protection circuit activated?

Make sure there is at least six inches of free space behind the SWA1801z.

Poor sound

• Is it loud and distorted? Make sure that you’re not overdriving a stage in the signal chain.

Verify that all level controls are set properly.

• Is the input connector plugged completely into the jack? Be sure all connections are secure. It’s a good idea to periodically clean all electrical connections with a non-lubricating electrical contact cleaner.

Noise

• Make sure all connections to the active loudspeakers are good and sound.

• Make sure none of the signal cables are routed near AC cables, power transformers, or other EMI-inducing devices.

• Is there a light dimmer or other SCRbased device on the same AC circuit as the

SWA1801z? Use an AC line filter or plug the

SWA1801z into a different AC circuit.

Hum

• Try disconnecting the cable connected to the

INPUT jack. If the noise disappears, it could be a “ground loop,” rather than a problem with the SWA1801z. Try some of the following troubleshooting ideas:

• Use balanced connections throughout your system for the best noise rejection.

• Whenever possible, plug all the audio equipment’s linecords into outlets which share a common ground. The distance between the outlets and the common ground should be as short as possible.

Repair

For warranty repair or replacement, refer to the warranty information on page 11.

Non-warranty repair for Mackie products is available at a factory-authorized service center.

To locate your nearest service center, visit www.

mackie.com, click “Support” and select “Locate a Service Center.” Service for Mackie products living outside the United States can be obtained through local dealers or distributors.

If you do not have access to our website, you can call our Tech Support department at 1-800-

898-3211, Monday-Friday, 7 am to 5 pm Pacific

Time, to explain the problem. Tech Support will tell you where the nearest factory-authorized service center is located in your area.

Need Help?

You can reach a technical support representative

Monday through Friday from 7 AM to 5 PM PST at:

1-800-898-3211

After hours, visit www.mackie.com and click Support, or email us at: [email protected]

R

9

SWA1801z SPECIFICATIONS

System Specifications

Frequency Range (–10 dB)

35 Hz–120 Hz

Frequency Response (–3 dB)

45 Hz–120 Hz

Maximum SPL @ 1m

129 dB

Peak Output @ 1m

135 dB

Crossover Frequency

120 Hz (12 dB/octave)

Input Type

Balanced differential

Input Impedance

Input Protection

50 k

Ω

Level protected

Thermal Protection

Input stage muting,

auto-reset

Transducer Specifications

Low-Frequency Transducer

Diameter

18˝ (457 mm)

Voice Coil Diameter

4.0˝ (102 mm)

Power Amplifier

Low-Frequency Power Amplifier

Rated Power

*

800 Watts continuous

1000 Watts peak

Rated THD

< 0.03%

Cooling

Passive

Line Input Power

US

Europe

120 V, 60 Hz

230 V, 50 Hz

Disclaimer

Since we are always striving to make our products better by incorporating new and improved materials, components, and manufacturing methods, we reserve the right to change these specifications at any time without notice.

“Mackie” and the “Running Man” figure are registered trademarks of LOUD Technologies Inc.

All other brand names mentioned are trademarks or

registered trademarks of their respective holders, and are hereby acknowledged.

©2005-2012 LOUD Technologies Inc.

All Rights Reserved.

Dimensions

23.5" (597 mm) 23.5" (597 mm)

11.2"

(284 mm)

3.5"

(89 mm)

* Rated power into loudspeaker’s rated impedance.

Physical Properties

Height

Width

Depth

Weight

28.5˝ (724 mm)

23.5˝ (597 mm)

23.5˝ (597 mm)

132 lbs. (60 kg)

Enclosure

15 mm thick multi-layered baltic

3.3"

(83 mm)

FRONT

3.3"

(83 mm)

Enclosure Geometry

Rectangular

Mounting Methods

Floor mount only

WARNING

: The cabinet has no rigging points and is not suitable for rigging.

NEVER

attempt to suspend the SWA1801z by its handles.

23.5" (597 mm)

TOP

SWA1801z On Axis Frequency Response

(with second and third harmonic components)

110

7.0"

(178 mm)

7.1"

(180 mm)

9.4"

(239 mm)

5.2"

(132 mm)

SIDE

10

100

90

80

70

60

50

40

20 50 100 200 500 1k

Frequency (Hz)

2k

Fundamental

Second

Third

5k 10k 20k

3.5"

(89 mm)

SWA1801z On Axis Frequency Response

(with second and third harmonic components)

SWA1801z Limited Warranty

A.

LOUD Technologies Inc. warrants all materials, workmanship and proper operation of this product for a period of

three years

from the original date of purchase. You may purchase an additional 24-month Extended Warranty (for a total of 60 months of coverage). Visit our website and follow the “Product

Registration” links for details (www.mackie.com). If any defects are found in the materials or workmanship or if the product fails to function properly during the applicable warranty period,

LOUD Technologies, at its option, will repair or replace the product.

This warranty applies only to equipment sold and delivered within the U.S. and Canada by LOUD

Technologies Inc. or its authorized dealers.

B.

For faster processing (not to mention a free gift), register online or mail in the product registration card.

C.

Unauthorized service, repairs, or modification of Mackie products will void this warranty. To obtain repairs or replacement under warranty, you must have a copy of your sales receipt from the authorized Mackie dealer where you purchased the product. It is necessary to establish purchase date and determine whether your Mackie product is within the warranty period.

D.

To obtain warranty repair or replacement:

Call Mackie Technical Support at 800/898-3211, 7 AM to 5 PM Monday through Friday (Pacific Time) to get authorization for repair or replacement. Alternately, go to the

Mackie website, click “Support” (www.mackie.com/support), and follow the instructions for reporting a warranty issue and submitting a request for an advance replacement.

2. Advance Replacement:

Mackie will ship a replacement unit to you along with an invoice for the suggested retail price of the replacement unit. You must return the defective unit immediately to cancel the invoice. If you do not return the defective unit within 30 days, you must pay the full amount stated in the invoice to satisfy your debt.

3. Repair:

When you call Mackie Technical Support, explain the problem and obtain a Service Request Number.

Have your Mackie product’s serial number ready.

You must have a Service Request Number before you can obtain factory-authorized service.

• Pack the product in its original shipping carton. Also include a note explaining exactly how to duplicate the problem, a copy of the sales receipt with price and date showing, your daytime phone number and return street address (no P.O. boxes or route numbers, please!), and the Service Request Number. If we cannot duplicate the problem or establish the starting date of your Limited

Warranty, we may, at our option, charge for service time and parts.

• Ship the product in its original shipping carton,

freight prepaid

to the authorized service center. Write the Service Request Number in

BIG PRINT

on top of the box.

The address of your closest authorized service center will be given to you by Technical Support, or it may be obtained from our website. Once it’s repaired, the authorized service center will ship it back by ground shipping, pre-paid (if it qualified as a warranty repair).

Note:

Under the terms of the warranty, you must ship or drop-off the unit to an authorized service center. The return ground shipment is covered for those units deemed by us to be under warranty.

Note:

You must have a sales receipt from an authorized

Mackie dealer for your unit to be considered for warranty repair.

Please keep your sales receipt in a safe place.

IMPORTANT: Make sure that the Service Request

Number is plainly written on the shipping carton. No receipt, no warranty service.

E.

LOUD Technologies reserves the right to inspect any products that may be the subject of any warranty claims before repair or replacement is carried out. LOUD Technologies may, at our option, require proof of the original date of purchase in the form of a dated copy of the original dealer’s invoice or sales receipt. Final determination of warranty coverage lies solely with LOUD Technologies.

F.

Any products returned to one of the LOUD Technologies factory-authorized service centers, and deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced. LOUD Technologies and its authorized service centers may use refurbished parts for repair or replacement of any product. Products returned to LOUD Technologies that do not meet the terms of this Warranty will not be repaired unless payment is received for labor, materials, return freight, and insurance. Products repaired under warranty will be returned freight prepaid by LOUD Technologies to any location within the boundaries of the USA or Canada.

G.

LOUD Technologies warrants all repairs performed for 90 days or for the remainder of the warranty period. This warranty does not extend to damage resulting from improper installation, misuse, neglect or abuse, or to exterior appearance. This warranty is recognized only if the inspection seals and serial number on the unit have not been defaced or removed.

H.

LOUD Technologies assumes no responsibility for the timeliness of repairs performed by an authorized service center.

I.

This warranty is extended to the original purchaser. This warranty may be transferred to anyone who may subsequently purchase this product within the applicable warranty period for a nominal fee. A copy of the original sales receipt is required to obtain warranty repairs or replacement.

J.

This is your sole warranty. LOUD Technologies does not authorize any third party, including any dealer or sales representative, to assume any liability on behalf of LOUD Technologies or to make any warranty for LOUD Technologies Inc.

K.

THE WARRANTY GIVEN ON THIS PAGE IS THE SOLE

WARRANTY GIVEN BY LOUD TECHNOLOGIES INC. AND

IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS AND

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANT-

ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE

WARRANTY GIVEN ON THIS PAGE SHALL BE STRICTLY

LIMITED IN DURATION TO THREE YEARS FROM THE DATE

OF ORIGINAL PURCHASE FROM AN AUTHORIZED MACKIE

DEALER. UPON EXPIRATION OF THE APPLICABLE WARRAN-

TY PERIOD, LOUD TECHNOLOGIES INC. SHALL HAVE NO

FURTHER WARRANTY OBLIGATION OF ANY KIND. LOUD

TECHNOLOGIES INC. SHALL NOT BE LIABLE FOR ANY

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES

THAT MAY RESULT FROM ANY DEFECT IN THE MACKIE

PRODUCT OR ANY WARRANTY CLAIM. Some states do not allow exclusion or limitation of incidental, special, or consequential damages or a limitation on how long warranties last, so some of the above limitations and exclusions may not apply to you. This warranty provides specific legal rights and you may have other rights which vary from state to state.

11

16220 Wood-Red Road NE • Woodinville, WA 98072 • USA

United States and Canada: 800.898.3211

Europe, Asia, Central and South America: 425.487.4333

Middle East and Africa: 31.20.654.4000

Fax: 425.487.4337 • www.mackie.com

E-mail: [email protected]