Marshall electronic V-R563P-SDI User’s Guide

Add to My manuals
2 Pages

advertisement

Marshall electronic V-R563P-SDI User’s Guide | Manualzz

Tally Indicators Illuminate when active

Dry Erase Label

Power On/Off switch

Illuminates red when system power is present

Illuminates Green when monitor is ON

Video signal selector switch

Illuminates when active

Video signal selector switch

Illuminates when active

Color Bar

On/Off switch

Illuminates when bars are active

Image Adjustment Controls

Marshall Electronics warranties to the first consumer, that this V-R563P-SDI Triple 5.6 inch LCD rack mounted monitor set will, under normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.

This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.

This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.

An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to effective use of the monitor by our technicians.

Due to constant effort to improve products and product features, specifications may change without notice.

Marshall Electronics

1910 East Maple Ave.

El Segundo, CA 90245

Tel.: 800-800-6608 • Fax: 310-333-0688

www.LCDRacks.com

Email: [email protected]

V-R563P -SDI

Product Overview

Features

Electrical Specifications

Mechanical Specifications

Operational Setup

Connectors

Switch Settings, Adjustments and Indicators

Warranty

6

7

4

5

8

1

2

3

The V-R563P-SDI has three independently controlled 5.6” active matrix LCD monitors. Each of the 5.6” panels produces high-resolution images with 960 x 234 pixels. The V-R563P-SDI also has a unique feature that allows the unit to tilt up or down for optimum viewing angle and installs into an EIA standard 19” rack. Each screen has one composite video with active loop through and one SDI (SMTPE 259M) input with active loop through, active clock recovery and automatic 75 Ω termination. There is also a money saving Digital to Analog conversion of each SDI signal. Every display has a built-in color bar generator, 3 Tally indicators, individual front mounted selector buttons with LED indicators and color, tint, brightness and contrast controls. The unit includes a universal voltage power supply and features auto recognition for NTSC or PAL signals.

• Small Footprint – occupies only 3RU of a standard EIA 19 inch rack

• Ready to mount – all brackets are factory installed

• Lightweight - Save over 30 pounds when compared to similar CRT models

• All adjustments and selections are readily available. No menus!

• Easy to use front panel selection of inputs

• NTSC or Pal operation with automatic signal format detection

• Switched A/B Composite inputs with active loop out

• All inputs automatically terminate

• Built in color bar generator for each display

• Includes V-PS12-3.3A Universal power supply (U.L. class 2)

• Unique 180 degree tilt adjustment

• Dry erase label for each screen

V-PS12-3.3A

Display (Viewing Area)

Screen Aspect

Resolution (Dots)

Dot Pitch

Pixel Response Time

Brightness (in cd/m²)

Contrast Ratio

System

Inputs per display

Outputs per display

Color Bar Signal

Power required

Operating temperature

5.6” diagonal (4.46” x 3.33”) (113.3 mm x 84.7mm)

4:3

960 pixel (320dot) W x 234H × 234V (225,000 pixels)

0.118mm(W) × 0.362mm (H)

35ms typical

300 cd/m²

150:1

PAL or NTSC with automatic detection. NTSC signal complies to SMPTE RS-170M

Composite BNC 75

self terminating 0.7V to 1.3 V P-P.

SDI BNC 75

self terminating with 500ft equalization.

3 Color Tally (15 pin D-Sub connection)

Active Composite loop through BNC.

Reclocked SDI loop through BNC.

10 bit Analog composite conversion of SDI signal BNC

Full field SMPTE

12 V D.C. from external power supply (included) max 3.0 AMP

320 F to 1100 F (00 C to 450 C)

Dimensions

V-R682P Weight

V-PS12-3.3A Power Supply Weight

2

19.125”W x 2.5”D x 5.25”H (120cm x 93cm x 25cm)

5.0 lbs (2.27kg)

1 lbs (0.454kg)

V-R563P-SDI Users Guide

1. Unpack the V-R563P-SDI and accompanying V-PS12-3.3A power supply. Physically inspect for any damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall

Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when installed to prevent possible damage to the V-R563P-SDI internal components.

3. Connect required cables for signal input and output.

Please note that power must be applied to the V-R563P-SDI for all outputs to be activated.

All BNC connectors should be rated for 75 Ω.

4. Plug the V-PS12-3.3A power supply into the A.C. source

5. Attach twist lock power connection from V-PS12-3.3A power supply to the back of the unit.

6. Turn on the V-R563P-SDI by depressing the power switch located on the front of the unit.

Connectors

* Tally lamps active when connected to ground

Monitor 3

Composite

Video In

Monitor 3

SDI In

Monitor 2

Composite

Video In

Monitor 2

SDI In

Monitor 1

Composite

Video In

Monitor 1

SDI In

Tally IN

DB-15 Female

Pin1-M3Grn

Pin2-M3Red

Pin6-M2Grn

Pin7-M2Red

Pin8-M2Yel

Pin9-Gnd

Pin10-Gnd

Pin3-M3Yel

Pin4-Gnd Pin12-M2Red

Pin5-Gnd

Pin11-M1Grn

Pin13-M3Yel

Pin14-Gnd-

Pin15-Gnd

Active

Output

Analog

Output converted from SDI

Input

Active

Output

Analog

Output converted from SDI

Input

Active

Output

Analog

Output converted from SDI

Input

12 VDC from

V-PS12-3.3A power supply

Left Pin - Pos

Right Pin- Neg

* Composite Video Inputs comply to SMPTE-170M

* SDI inputs comply to SMPTE259M / ITU-R BT601

* Composite Video and SDI Outputs Require Power to be applied for activation

Marshall Electronics 3

advertisement

Related manuals

advertisement