Maxus | MXN10300 | User's Manual | Maxus MXN10300 User's Manual

Maxus MXN10300 User's Manual
See Warranty on page 8 for important information about commercial use of this product.
Operating Instructions
MXN10300
Limited Warranty
1.
DURATION: From the date of purchase by the original purchaser as follows: Campbell Hausfeld (Standard Duty and
Unannounced) – One (1) Year, (Serious Duty) – Two (2) Years, (Extreme Duty) – Three (3) Years; IronForce by Campbell
Hausfeld – One (1) Year; Farmhand – Three (3) Years; Maxus – Five (5) Years.
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,
Harrison, Ohio, 45030, Telephone: (800) 543-6400
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the
Campbell Hausfeld product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air accessory supplied or manufactured by Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the
duration of the warranty period.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial,
industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States
do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance
with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or
failure to operate products in accordance with instructions shall also include the removal or alteration of any safety
devices. If such safety devices are removed or altered, this warranty is void.
D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.
E. Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields,
driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants, material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters, collets,
chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other expendable part
not specifically listed. These items will only be covered for ninety (90) days from date of original purchase.
Underlined items are warranted for defects in material and workmanship only.
F. Cosmetic defects that do not interfere with the product’s function.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service
Center. Freight costs, if any, must be borne by the purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be
scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability
of replacement parts.
This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may
also have other rights which vary from state to state or country to country.
MXN10300
Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death and/or
property damage! Retain instructions for future reference.
Narrow Crown
Stapler
Table of Contents
General Safety . . . . . . . . . . . . .1-3
Specifications . . . . . . . . . . . . . . .2
Operating The Tool . . . . . . . . .3-5
Operational Mode . . . . . . . . . . .4
Troubleshooting . . . . . . . . . . . . .7
Warranty . . . . . . . . . . . . . . . . . . .8
Description
This stapler is designed for cabinetry,
casebacks, decorative trim and crafts.
Features include: no-mar tip,
adjustable exhaust, single sequential
trigger, quick clear nose, and an
adjustable depth of drive mechanism.
General Safety
Information
CALIFORNIA PROPOSITION 65
You
can create dust when you cut,
sand, drill or grind materials such as wood, paint,
metal, concrete, cement, or
other masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
!
DANGER
This manual contains safety, operational and maintenance information.
Contact your Campbell Hausfeld representative if you have any questions.
OPERATOR’S RESPONSIBILITY:
The tool operator is responsible for:
• Reading and understanding tool
labels and manual.
• Selecting an appropriate tool actuation system, taking into consideration the work application for which
the tool is used.
• The safe use of the tool.
• Ensuring that the
tool is used only
when the operator
and all other personnel in the work area
are wearing ANSI Z87 eye protection equipment, and when
required, other appropriate protection equipment such as head, hearing and foot protection equipment.
Serious eye or permanent hearing
loss could result.
• Assuring that the tool is kept in safe
working order as described in this
manual.
Model MXN10300
Locate model and date code on tool
magazine and under nozzle shield,
and record below:
Model No. ________________________
Date Code.________________
Retain these numbers for
future reference.
EMPLOYER’S RESPONSIBILITY:
•
•
•
•
Selecting an appropriate tool actuation system, taking into consideration the work application for which
the tool is used.
Ensuring that this manual is available to operators and personnel
performing maintenance.
The safe use of the tool.
Enforcing that the
tool is used only
when the operator
and all other personnel in the work area
are wearing ANSI Z87 eye protection equipment, and when
required, other appropriate protec-
•
•
•
tion equipment such as head, hearing and foot protection equipment.
Serious eye or permanent hearing
loss could result.
Assuring that the tool is kept in
safe working order as described in
this manual.
Assuring the proper maintenance
of all tools in employer’s possession.
Ensuring that tools which require
repair are not further used before
repair. Tags and physical segregation are recommended means of
control.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
8
Maxus Tools meet or exceed Industries’
Standards as set forth by the American
National Standard Institute/International
Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2004
IN701400AV 11/04
MXN10300
Operating Instructions
General Safety
Information (Continued)
Vapors could ignite by a spark and
cause an explosion which will result
in death or serious personal injury.
Always remain in a
firmly balanced
position when
using or handling
the tool.
Danger indicates
an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
!
DANGER
Read and understand
tool labels and manual.
Failure to follow warnings, dangers, and cautions could result in
DEATH or SERIOUS INJURY.
Do not remove, tamper with, or otherwise cause the Work
Contact Element
(WCE) or trigger to
become inoperable.
Do not operate any
tool which has been modified in a
like fashion. Death or serious personal injury could result.
Do not use any type
of reactive gases,
including, but not limO
ited to, oxygen and
CO2
combustible gases, as
a power source. Use
filtered, lubricated, regulated compressed air only. Use of a reactive
gas instead of compressed air may
cause the tool to explode which will
cause death or serious personal
injury.
Do not touch
the trigger
unless driving
fasteners.
Never attach
air line to tool
or carry tool
while touching the trigger. The tool
could eject a fastener which will
result in death or serious personal
injury.
Use only a pressureregulated compressed
air source to limit the
air pressure supplied
100
to the tool. The regupsi
lated pressure must
not exceed 100 psi. If the regulator
fails, the pressure delivered to the
tool must not exceed 200 psi. The
tool could explode which will cause
death or serious personal injury.
Warning indicates
!
a potentially
hazardous situation which, if not avoided, COULD result in death or
serious injury.
WARNING
Always disconnect the tool
from the power
source when
unattended,
performing any
maintenance or
Never use gasoline
or other flammable
liquids to clean the
tool. Never use the
tool in the presence
of flammable liquids or gases.
Tool Components and Specifications
• REQUIRES: 0.8 SCFM with 10
fasteners per minute @ 90 PSI
• AIR INLET: 1/4” NPT
• STAPLE SIZE RANGE: 3/8” to 1-1/4”
• MAGAZINE CAPACITY:
100 Staples per load, 18 gauge
• WEIGHT: 2 lb., 15 oz.
• LENGTH: 10-1/2”
• HEIGHT: 9-1/2”
• MAXIMUM PRESSURE: 100 PSI
• PRESSURE RANGE: 60 – 100 PSI
repair, clearing a jam, or moving the
tool to a new location. Always
reconnect the air line BEFORE loading any fasteners. Do not load the
tool with fasteners when either the
trigger is depressed or the Work
Contact Element (WCE) is engaged.
The tool could eject a fastener causing death or serious personal injury.
Always fit tool
with a fitting or
hose coupling
on or near the
tool in such a
manner that all
compressed air in the tool is discharged at the time the fitting or
hose coupling is disconnected. Do
not use a check valve or any other fitting which allows air to remain in the
tool. Death or serious personal injury
could occur.
Never place hands or
any other body parts in
the fastener discharge
area of the tool. The
tool might eject a fastener and could result
in death or serious personal injury.
Never carry the
tool by the air
hose or pull the
hose to move the
tool or a compressor. Keep hoses
away from heat,
oil and sharp edges. Replace any
hose that is damaged, weak or
worn. Personal injury or tool damage could occur.
MXN10300
Operating Instructions
Troubleshooting Guide
! WARNING
Stop using stapler immediately if any of the following problems occur. Serious personal injury
could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized
Service Center.
Problem
Cause
Solution
Air leaking at trigger valve
area.
O-Rings in trigger valve housing are
damaged
Replace o-rings and check operation of Work Contact
Element (WCE)
Air leaking between housing and nose.
Loose screws in housing
Damaged O-Rings
Damage to bumper
Tighten screws
Replace o-rings
Replace bumper
Air leaking between housing and cap.
Loose screws
Damaged gasket
Tighten screws
Replace gasket
Stapler skips driving staple.
Worn bumper
Dirt in nose piece
Dirt or damage prevent staples or
pusher from moving freely in magazine
Damaged pusher spring
Inadequate air flow to stapler
Worn O-Ring on piston or lack of lubrication
Damaged O-Ring on trigger valve
Air leaks
Cap gasket leaking
Replace bumper
Clean drive channel
Clean magazine
Stapler runs slow or has
loss of power.
Stapler not lubricated sufficiently
Broken spring in cylinder cap
Exhaust port in cap is blocked
Lubricate stapler
Replace spring
Replace damaged internal parts
Staples are jammed in stapler.
Guide on driver is worn
Staples are not correct size
Staples are bent
Magazine or nose screws are loose
Driver is damaged
Staples loaded incorrectly
Replace guide
Use only recommended staples
Replace with undamaged staples
Tighten screws
Replace driver
Review Loading/Unloading section in this manual
Air leaking at trigger valve
stem.
O-Rings or seals are damaged
Replace o-rings or seals
Cap exhaust
Magazine
Nozzle shield
Trigger
Latch
Quick clear nose
Work contact
element (WCE)
Adjustable depth control
(not visible)
Fastener discharge area
Fastener loading area
2
7
Replace spring
Check fitting, hose, or compressor
Replace and lubricate o-rings
Replace o-rings
Tighten screws and fittings
Replace gasket
MXN10300
Operating Instructions
MXN10300
Operating Instructions
General Safety
Information (Continued)
Staples
Interchange Information
MXN10300 can use 3/8” to 1-1/4” 18 gauge 1/4” crown staples designed for the following tools:
• Campbell Hausfeld® SN258K
• Hitachi® N3804AB
• Porter Cable® NS100, NS150
• Senco® SLS15, SLS18, SLS25XP
Always assume the tool contains
fasteners. Respect the tool as a
working implement; no horseplay.
Always keep others at a safe distance from the work area in case of
accidental discharge of fasteners.
Do not point the tool toward yourself or anyone whether it contains
fasteners or not. Accidental triggering of the tool could result in death
or serious personal injury.
Do not drive a fastener on top of
other fasteners.
The fastener could
glance and cause
death or a serious
puncture wound.
Do not operate
or allow anyone ! WARNING
else to operate
the tool if any
warnings or
warning labels
are not legible.
Warnings or warning labels are located on the tool magazine and body.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, examine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
!
a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate
injury.
CAUTION
Do not make any modifications to the
tool without first obtaining written
approval from Campbell Hausfeld. Do
not use the tool if any shields or
guards are removed or altered. Do
not use the tool as a hammer.
Personal injury or tool
damage may occur.
Operating The
Stapler
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the tool.
1. The air com60 psi
pressor must be
Min.
able to main100 psi
tain a miniMax.
mum of 60 psi
when the tool is being used. An
inadequate air supply can cause a
loss of power and inconsistent
driving.
Avoid long extended periods of
work with the tool. Stop using the
tool if you feel pain in hands or
arms.
Always check that the Work Contact
Element (WCE) is operating properly. A fastener could accidentally be
driven if the WCE is not working
properly. Personal injury may occur
(See "Checking the Work Contact
Element" Section).
2. Always use air supply hoses with a
minimum working pressure rating
equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is
greater. Use 3/8” air hose for runs
up to 50’. Use 1/2” air hoses for 50’
run or longer. For better performance, install a 3/8” quick plug (1/4”
NPT threads) with an inside diameter of .315” (8mm) on the tool and a
3/8” quick coupler on the air hose.
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the tool. Personal injury
may occur.
Notice indicates
important information, that if not followed, MAY
cause damage to equipment.
NOTICE
Avoid using the tool when the magazine is empty. Accelerated wear on
the tool may occur.
150 psi or greater
Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
3/8” I.D.
3. Use a pressure regulator on the
compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between
60 and 100 psi.
Recommended Hookup
Quick Plug
(Optional)
Quick Quick
Plug Coupler
Filter/Regulator
8
1
6
5
4
3
7
1
.
.
1
Air
Hose
6
3
1
1
MPA
bar
psi
Quick
Coupler
(Optional)
9
.
.
1
1
1
MXN10300
Operating Instructions
Operating The
Stapler (Continued)
OPERATIONAL MODE
Always know the
operational mode
of the tool before using. Failure to
know the operational mode could
result in death or serious personal
injury.
! WARNING
SINGLE SEQUENTIAL MODE
This mode
requires the trigger to be pulled
each time a fastener is driven. The tool can be actuated by depressing the Work Contact
Element (WCE) against the work surface followed by pulling the trigger.
The trigger must be released to reset
the tool before another fastener can
be driven.
OPERATING A SEQUENTIAL TRIP
TOOL
Check the operation of the Work
Contact Element (WCE) trip mechanism
before each use. The WCE must move
freely without binding through its
entire travel distance. The WCE spring
must return the WCE to its fully extended position after being depressed. Do
not operate the tool if the WCE trip
mechanism is not operating properly.
Personal injury may occur.
!
CAUTION
1. Disconnect the
air supply from
the tool.
Operating The
Stapler (Continued)
5. Depress the Work
Contact Element
(WCE) against the
work surface without pulling the trigger. The tool MUST NOT OPERATE.
Do not use the tool if it operates
without pulling the trigger.
Personal injury may result.
ADJUSTING THE DIRECTION OF THE
EXHAUST
The tool is
equipped with an
adjustable direction exhaust
Rotate
deflector. This is
intended to allow the user to change
the direction of the exhaust. Simply
twist the deflector to any direction
desired.
6. Remove the tool
from the work surface. The Work
Contact Element
(WCE) must return
to its original down
position. The tool MUST NOT
OPERATE. Do not use the tool if it
operates while lifted from the work
surface. Personal injury may result.
7. Pull the trigger and
depress the
work contact
element (WCE) against the work
surface. The tool MUST NOT OPERATE.
1
2
8. Depress the
Work Contact
Element
(WCE) against
the work surface. Pull the trigger.
The tool MUST OPERATE.
1
2
4. Push the magazine cover forward until latch
button pops
up.
5. Always unload all fasteners before
removing tool from service.
Unloading is the reverse of loading,
except always disconnect the air
supply before unloading.
CLEARING A JAM FROM THE TOOL
1. Disconnect the air
supply from the
tool.
ADJUSTING THE FASTENER
PENETRATION
The tool is equipped with an adjustable
depth of drive feature. This allows the
user to determine how deep a fastener
will be driven into the work surface.
2. Remove all fasteners from the magazine (see Loading/ Unloading).
1. Adjust operating pressure so fasteners are driven consistently. Do not
exceed 100 psi.
2. To drive the fastener shallower, turn
the wheel (C) to right to the extent
desired.
3. To sink a fastener deeper, turn the
wheel (C) to left to the extent
desired.
An improperly
!
functioning tool
must not be used. Do not actuate the
tool unless the tool is placed firmly
against the work piece.
WARNING
2. Remove all fasteners from
the magazine
(see Loading/
Unloading).
3. Make sure the trigger and work contact element (WCE)
move freely up and
down without sticking or binding.
4. Reconnect air
supply to the
tool.
Magazine rail
LOADING/UNLOADING THE TOOL
1. Always connect the tool to the air
supply before loading fasteners.
movement
2. Push down
on the latch
button. Pull
back on the
magazine
cover.
MXN10300
Operating Instructions
4. The door can now
be rotated, exposing the jammed
fastener.
5. Remove the
jammed fastener, using
pliers or a
screwdriver if
required.
6
BUILT TO LAST
4
Please call our Tool Hotline at
1-888-241-5858 with any questions
regarding the operation or repair of
this tool or for additional copies of this
manual.
Fastener And Replacement
Parts
7. Push button down
again to lift the
hook. Close the
door and release
the button to
reengage the hook with the nose.
8. Make sure the trigger and work contact element (WCE)
move freely up and
down without sticking or binding.
Magazine rail
Failure to remove
!
all fasteners will
cause the fasteners to eject from the front
of the tool.
WARNING
3. Undo hook by
pushing down on
the button on the
side of the magazine. The button
will disengage the hook from the
nose.
(C)
4. Make sure trigger
and work contact
element (WCE)
movement
move freely up and
down without binding or sticking
after each adjustment.
5
Use only
18 gauge fasteners (or equivalent - see Fastener
Interchange Information). Tool performance, safety and durability could be
reduced if improper fasteners are used.
When ordering replacement parts or
fasteners, specify by part number.
! WARNING
Rotate door back
into the closed
position.
Latch
Button
3. Load a clip of fasteners with the
crowns straddling the magazine rail.
Technical Support
movement
Tool Repair
Only qualified personnel should repair
the tool and they should use genuine
Campbell Hausfeld replacement parts
and accessories, or parts and accessories which perform equivalently.
Assembly Procedure For
Seals
When repairing a tool, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising