Maytag MVWB700BW Dimension Guide
Add to my manuals2 Pages
Maytag MVWB700BW is a front-loading washer with a spacious 4.5 cubic feet capacity, allowing you to wash large loads of laundry with ease. It features a variety of wash cycles, including a quick wash cycle for smaller loads and a bulky/bedding cycle for larger items. The washer also has a built-in water heater, which can be used to improve the cleaning performance of certain cycles.
Additionally, the Maytag MVWB700BW is equipped with a number of features to make laundry day easier, such as an automatic detergent dispenser and a wrinkle control option.
advertisement
PRODUCT MODEL NUMBERS
MVWB700B, MVWB725B
Washer Dimensions:
44"
(1118 mm)
27.5"
(698 mm) 27.5"
(698 mm)
Front-Loading Washer
Spacing for recessed area or closet installation
3"
(76 mm)
14" max.
(356 mm)
48 in.
2
(310 cm 2 )
17"
(432 mm)
5"
(126 mm)
1"
(25 mm)
1"
(25 mm)
3"
(76 mm)
24 in.
2
(155 cm 2 )
Installation spacing for recessed area or closet installation
The dimensions shown below are the recommended spacing for this washer.
■ Additional spacing should be considered for ease of installation and servicing.
■ Additional clearances might be required for wall, door, floor moldings, and dryer venting.
■ Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.
■ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. Companion appliance spacing should also be considered.
W10196566B1
08/2013
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system Floor drain system
4 1 /
2
"
(114 mm)
39"
(990 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe must be at least 39" (990 mm) high; install no higher than 96"
(2.44 m) from bottom of washer. If you must install higher than
96" (2.44 m), you will need a sump pump system.
Wall standpipe drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be purchased separately. To order, please see toll-free phone numbers in your “Use and Care Guide.” Minimum siphon break:
28" (710 mm) from bottom of washer. (Additional hoses may be needed.)
Laundry tub drain system
4 1 /
2
"
(114 mm)
4 1 /
2
"
(114 mm)
See requirements for floor standpipe drain system.
30"
(762 mm)
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (990 mm) above floor; install no higher than 96" (2.44 m) from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with cable tie.
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project