jx-epseries digital output

jx-epseries digital output
135-04-229-015-EH-0115.pdf
135-04-229-015-EH-0115
JX-EP SERIES
DIGITAL OUTPUT
The JX-EP series linear position transducer with digital output is oriented for use
in moderate duty applications in hostile wet or dry environments. The chemical resistant thermoplastic case of the transducer with integral dust wiper is factory configurable to NEMA 12
(IP-52) for dust protection or to NEMA 4X (IP-65) for applications where exposure to washdown,
rain, oil and other liquids may occur.The sealed case is achieved through the use of o-rings and
a low friction shaft seal. The wire rope exit direction may be specified at time of order or may
be user adjusted at time of installation. The standard electrical connection includes a sealed
bulkhead fitting and multi-conductor electrical cable. An optional cable to cable connector with
mating connector may be added to the electrical cable. Alternatively, the cable to cable connector may be ordered without the mating connector. The mating connector with a length of electrical
cable attached may be ordered as a separate item. As a convenience, optional connector locations on the transducer
body are offered. The standard electrical output of the unit is a TTL level two channel square wave in quadrature. Optional
outputs include line driver and push-pull circuits.
SPECIFICATIONS
GENERAL
Measurement Range..................See Range Table below
Sensing Device ..........................Digital Encoder
Nominal Resolution[2]
10" range..................................445 counts/inch, 17.5 counts/mm
15", 30" range...........................327 counts/inch, 12.9 counts/mm
20", 40" range...........................246 counts/inch, 9.7 counts/mm
25", 50" range...........................198 counts/inch, 7.8 counts/mm
60" range..................................166 counts/inch, 6.5 counts/mm
80" range..................................126 counts/inch, 5.0 counts/mm
Linearity .....................................±0.10% Full Scale
Repeatability
(in times 1 counting mode).........±1 Count, ranges to 25"
±2 Counts, ranges 30" to 80"
Construction ..............................Thermoplastic Body
Wire Rope...................................Ø.018 (0.46 mm) Jacketed Stainless Steel
Wire Rope Tension......................See Supplemental Data[1]
Weight .......................................6.3 oz. (180 gm)
Connection ................................24 AWG Shielded Electrical Cable
LIFE (to wire rope replacement)
Ranges 10" to 25".................... 1,000,000 full stroke cycles
Ranges 30" to 80".................... 500,000 full stroke cycles
ENVIRONMENTAL
Operating Temperature............ -40°C to 70°C
Storage Temperature............... -40°C to 80°C
Operating Humidity.................. 95% R.H. non-condensing IP-52
case 100% R.H. IP-65 case
Vibration.................................. 20 G’s maximum
Ingress Protection.................... NEMA 4X (IP-65) or NEMA 12 (IP-52)
ELECTRICAL
Excitation Voltage ................... +5 VDC ±5% or 8-28 VDC
Excitation Current ................... 85mA MAX
Output...................................... 2 channel square wave in
Quadrature TTL Level Current
Sinking with 65 KΩ Pullups
FOOTNOTES TO SPECIFICATIONS
1. Supplemental Data section located at end of JX Series pages.
2. Resolution shown is for times one counting mode. Resolution may be increased by
a factor of four with interface electronics capable of quadrature times 4 counting mode.
MODEL NUMBER CONFIGURATION
Basic Configuration
(for all ranges)
JX-EP-50-N11-210-1PU
RANGE
10........... 10" (250 mm)
15........... 15" (390 mm)
20..........20" (500 mm)
25..........25" (640 mm)
30..........30" (750 mm)
40........ 40" (1000 mm)
50........ 50" (1250 mm)
60........ 60" (1500 mm)
80........80" (2000 mm)
WIRE ROPE
INGRESS PROTECTION
ELECTRICAL CABLE
N.........Ø.018 (0,45 mm) Nylon Jacketed Stainless Steel
1.........Standard (See Table A & B for values)
1............ IP-65 (NEMA 4X) dust and
spraying water protection
2............ IP-52 (NEMA12) dust and dripping liquids
WIRE ROPE EXIT DIRECTION
ELECTRICAL OUTPUT
Use Number designators shown
1.... 5 VDC current sinking 2 channel
2.... 5 VDC current sinking differential line drive
3.... 5 VDC push-pull differential line drive
4.... 8 to 28 VDC current sinking differential line drive
5.... 8 to 28 VDC push-pull differential line drive
P........... 150 mm (6”) pigtail
1........... 1 m (3’ )
2........... 2 m (6.5’ )
3........... 3 m (10’ )
4........... 4 m (13.5’ )
5........... 5 m (16.5’ )
WIRE ROPE TENSION
See TABLE 3, Electrical Output Options on next
page for waveform and output stage configuration.
CONNECTOR LOCATION
END VIEW
Use Number designators shown
TOP VIEW
CONNECTOR
U........... No connector
C........... Cable to cable connector
with mating connector
K........... Cable to cable connector with NO mating connector
For Option “K”, mating connector
with electrical cable is available as
P/N 10325-xM where “x” is required
length in meters
135-04-229-015-EH-0115.pdf
135-04-229-015-EH-0115
JX SERIES
SUPPLEMENTAL DATA
DIMENSIONAL INFORMATION
JX Series – Ranges to 50” (1250 mm)
JX Series – Ranges 60” (1.5 m) and 80” (2 m)
TABLE A
RANGE
2, 10
2.8, 15, 30
3.8, 20, 40
4.7, 25, 50
TABLE B
DIM “A”
NOMINAL
WIRE ROPE
TENSION
(in)
(mm)
(oz)
(N)
.36
.50
.66
.82
9.1
12.7
16.7
20.8
16
14
11
8
4.4
3.9
3.1
2.2
RANGE
DIM “A”
60
80
.98 24.9
1.28 32.5
(in)
(dimensions in brackets are millimeters)
(mm)
NOMINAL
WIRE ROPE
TENSION
(oz)
(N)
10
8.6
2.8
2.4
(dimensions in brackets are millimeters)
TABLE 3 – JX-EP Series ELECTRICAL OUTPUT OPTIONS
OPTION
OUTPUT TYPE
OUTPUT STAGE
1
5 VDC TTL Two Channel Current Sinking
2
5 VDC TTL Current Sinking Differential Line Drive
3
4
5
WAVEFORM
Two channels in quadrature with 65KΩ internal pullup
resistors. 5 VDC input voltage
Current sinking line drive output. 2KΩ internal pullup
resistors. 5 VDC input voltage
5 VDC Push-Pull Differential Line Drive
Push-Pull, current sourcing and current sinking output. 5
VDC input voltage. Output is compliant with requirements
of TIA/EIA-422-B.
8 to 28 VDC Current Sinking Differential Line Drive
Current sinking line drive output with 10KΩ internal pullup
resistors. 8 to 28 VDC input voltage
8 to 28 VDC Push-Pull Differential Line Drive
Push-Pull, current sourcing and current sinking output.
8 to 28 VDC input voltage.
10067 – Auxiliary Wire Rope Extension Kit
The auxiliary wire rope extension may be used to facilitate mounting the transducer
remotely from the measurement point. The clip on the extension attaches to the eye fitting
on the transducer. The eye fitting on the opposite end, which is identical to the fitting on
the transducer, mounts to the moving element. The extension kit is also available with
the clip end unterminated for situations where it is more convenient to size the wire rope
length during installation. Clip and crimp fitting are included with the unterminated version.
Ø.188 (Ø4.8 mm) Eye Fitting
This end connects to the
moving element.
Clip--This end connects to
fitting on transducer
Crimp Sleeve
"L" ± 0.3 cm (0.12")
DIMENSION “L”
Specify Dimension “L” in centimeters to the
nearest whole centimeter
NOTES:1.1 cm = 0.394”, 1 inch = 2.54 cm
2.Shortest length “L” is 5 cm (approximately 2”)
UNTERMINATED CLIP END
Leave Blank...... Completed kit (No designator required)
U...................... Unterminated Clip End
(clip and crimp sleeve included in kit)
Headquarter Switzerland:
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Phone +41 44 877 35 00
[email protected]
Office Germany:
Pewatron AG
Neumarkter Straße 86a
D-81673 Munich
Phone +49 89 260 38 47
[email protected]
We are here for you. Addresses and Contacts.
Sales Switzerland & Liechtenstein
Sales International Key Accounts
Postcode 3000 – 9999
Postcode 1000 – 2999
Basil Frei
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Eric Letsch
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Peter Felder
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Phone + 41 44 877 35 18
Mobile + 41 76 279 37 26
Phone + 41 44 877 35 14
Mobile + 41 76 491 66 70
Phone + 41 44 877 35 05
Mobile + 41 79 406 49 83
[email protected]
[email protected]
[email protected]
Sales Germany
Postcode 00000 – 31999
Postcode 38000 – 39999
Postcode 80000 – 99999
Postcode 32000 – 37999
Postcode 40000 – 79999
Sales Austria
Kurt Stritzelberger
Pewatron AG
Neumarkter Straße 86a
D-81673 Munich
Gerhard Vetter
Pewatron AG
Fürstenbergstraße 12
D-55422 Bacharach-Medenscheid
Kurt Stritzelberger
Pewatron AG
Neumarkter Straße 86a
D-81673 Munich
Phone + 49 89 260 52 80
Mobile + 49 171 803 41 35
Phone + 49 674 394 75 75
Mobile + 49 163 762 74 30
Phone + 49 89 260 52 80
Mobile + 49 171 803 41 35
[email protected]
[email protected]
[email protected]
Pressure Sensors
Gas sensors / Gas sensor modules
Load cells
Linear position sensors
Angle sensors
Philipp Kistler
Phone + 41 44 877 35 03
philipp.kistl[email protected]
Thomas Clausen
Phone + 41 44 877 35 13
[email protected]
Eric Letsch
Phone + 41 44 877 35 14
[email protected]
Accelerometers
Power supplies
Current sensors
Eric Letsch
Phone + 41 44 877 35 14
[email protected]
Sebastiano Leggio
Phone + 41 44 877 35 06
[email protected]
Sebastiano Leggio
Phone + 41 44 877 35 06
[email protected]
Drive technology
CH Postcode 5000 – 9999 / DE
Drive technology
CH Postcode 1000 – 4999 / AT / IT / FR
Roman Homa
Mobile + 41 79 444 00 86
[email protected]
Christian Mohrenstecher
Mobile +41 76 444 57 93
[email protected]
Sales Other Countries / Product Management
Competitive sensor & power supply solutions worldwide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement