USB 10/100M Fast Ethernet

H-BT10U
USB Wireless Bluetooth TM Adapter
-1-
FCC Part 15 Class B Registration
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interface, and
2) This device must accept any interface received, including interface that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
Changes or modifications not expressly approved by party responsible for compliance
could void the user the user authority to operate the equipment.
1)
To comply with FCC RF exposure compliance requirements, a separation distance of
at least 20 cm must be maintained between the antenna of this device and all persons.
2)
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Licensed Software
Bluetooth for Windows (BTW) is the licensed software owned by WIDCOMM, Inc.
(“WIDCOMM”).
Trademark(s) ™ and Registered Trademark(s) ®
Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc., U.S.A.
Microsoft, Windows are registered trademarks of Microsoft Corporation. Other brand and
product names are trademarks and/or registered trademarks of their respective holders.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
VCCI Mark Warning
-2-
LIMITED WARRANTY
Hawking Technology guarantees that every H-BT10U USB BluetoothTM Adapter is free
from physical defects in material and workmanship under normal use for two (2) years
from the date of purchase. If the product proves defective during this two-year
warranty period, call Hawking Customer Service in order to obtain a Return
Authorization number. Warranty is for repair or replacement only. Hawking
Technology does not issue any refunds. BE SURE TO HAVE YOUR PROOF OF
PURCHASE. RETURN REQUESTS CAN NOT BE PROCESSED WITHOUT PROOF
OF PURCHASE. When returning a product, mark the Return Authorization number
clearly on the outside of the package and include your original proof of purchase.
IN NO EVEN SHALL HAWKING TECHNOLOGY’S LIABILTY EXCEED THE
PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE
OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE OR ITS
DOCUMENTATION. Hawking Technology makes no warranty or representation,
expressed, implied or statutory, with respect to its products or the contents or use of this
documentation and all accompanying software, and specifically disclaims its quality,
performance, merchantability, or fitness for any particular purpose. Hawking
Technology reserves the right to revise or updates its products, software, or
documentation without obligation to notify any individual or entity. Please direct all
inquiries to:[email protected]
-3-
This Hawking H-BT10U BluetoothTM USB Adapter is designed to plug into an available
Universal Serial Bus port connecting to a desktop or laptop PC. The H-BT10U allows you to
make short-range wireless connections between Bluetooth devices such as cellular phones,
personal digital assistants (PDA), and desktop and notebook computers.
The H-BT10U BluetoothTM USB Adapter uses fast 2.4Ghz radio signals to transmit voice and
data. BluetoothTM transmission ensure both protection from interference and secure data
transfers. BluetoothTM helps people share and access information with ease.
Link your notebook with your handheld, mobile phone, printer or other BluetoothTM devices
within your personal area network (PAN) via a secure short-range wireless radio link. Get rid
of all those troublesome cables and automatically share documents, browse the Internet and
synchronize calendars, address books and more.
Features
Complies with Bluetooth 1.1 specification.
Uses 2.4 GHz ISM frequency band.
High-speed Wireless Transmissions, up to 723 Kbps Data Throughput.
Enable wireless connectivity between a notebook computer and other Bluetooth
devices
Connections within ranges up to 32 feet (10 meters).
Provides a high degree of security for communications between Bluetooth devices.
Connect with Bluetooth devices outside your PAN to quickly and easily share
data, files and information with a friend or co-worker.
Synchronize devices in your Personal Area Network to keep your data consistent.
Plug and play installation in Windows98 /ME / 2000 / XP.
-4-
Note: The H-BT10U Software (Version 1.2.2.6 or above)
should be installed prior to the hardware installation.
Once the installation CD is inserted into the computer’s CD-ROM drive, the Auto-Run
function will automatically guide you to start the software installation. If the Auto-Run
function does not start automatically, please view the contents of the installation CD to find
the “setup.exe” file and double-click the “setup” icon to continue.
Note: Before you install an upgraded version of the software, be sure to uninstall any
previous version, which already exits in your computer. For details of un-installation
procedures, refer to the later section titled “Software Un-installation”.
For Windows 98(SE)/ME/2000/XP
1. Once the Welcome screen appears, click the Next button.
2. When the License Agreement screen is displayed, read the License Agreement, then click
the radio button to the left of “I accept the terms in the license agreement” and click the
Next button.
-5-
3. On the Device Information screen, enter the required information:
Device Name—other Bluetooth-enabled devices; when inquiring about devices within
radio range you will see the user-configured device name.
The name can be changed after the installation process through the BTW Configuration
Panel.
Device Type—click on the down arrow and choose Desktop or Laptop from the
drop-down list. The device type can be changed after the installation process is completed
through the BTW Configuration Panel.
Click the Next button.
4. On the Destination Folder screen, click the Change button to browse to a new
destination folder for the BTW software. Otherwise, click the Next button to accept the
default folder.
-6-
5. The InstallShield Wizard will be ready to install the BTW software. If you need to review
or change any settings, click the Back button. Click the Cancel button to exit the
Wizard. Otherwise, click the Install button
6. Click OK at the following message (only for Windows 2000/XP installation).
7. The Bluetooth Installation Software screen displays the installation progress. If prompted
to insert the Windows CD, do so and follow the on-screen instructions.
8. When finished, click Finish to end the Installation Wizard.
-7-
9. Remember to restart your computer to have the new configuration take effect.
-8-
SOFTWARE UN-INSTALLATION
1.
In Windows, go to Start →Settings→ Control Panel→ Add or Remove Programs.
2.
Select Windcomm Bluetooth Software… and click the Remove button.
-9-
Note: The hardware installation should be only performed when the software is
well installed. Install your software CDROM before inserting the H-BT10U into
your computer’s USB port!
Precaution
Before the installation, make sure the USB port exists in your
computer and is enabled. To check this, go to My Computer Control
Panel System. Open the Device Manager tab. If the Universal Serial
Bus controller device is found, it means your USB port is installed and
enabled. If not, either no USB port is installed or the USB bios is not
properly enabled. In this case, consult your computer dealer for USB
support.
- 10 -
Getting Connected
1.
If the device is connected to the USB port on a desktop computer, use the included USB
adapter cable to connect your BluetoothTM USB Adapter with your computer.
2.
Locate the USB host port of your system. Align the USB connector (the thinner end) of
the USB adapter toward the USB host port. Push evenly and steadily until the USB
connector it is seated firmly.
3.
Plug your BluetoothTM USB Adapter into the thicker end of the USB adapter cable.
4.
As soon as the device is properly plugged to your computer will automatically detect the
device and prompt you with the following message. Select “Install the software
automatically (Recommended)” And press Next to continue.
- 11 -
5.
Select “Continue Anyway” when the following message appears.
6.
Press Finish to complete the hardware installation.
- 12 -
Once the software is well installed, your computer should display a Bluetooth icon
on the
bottom right corner of your taskbar. Right click on the icon to configure the H-BT10U.
Select Hardware. Check if “USB Bluetooth Device” is on the devices listed in the display
window. If it is listed, your H-BT10U USB Bluetooth Adapter is properly installed.
- 13 -
BASIC OPERATION
Precaution: For the best performance, we recommend that the Bluetooth devices you are
setting for transferring files should be within a range of 10 meters of each other.
Before you start communicating with a Bluetooth device, you need to:
1.
Search Bluetooth devices in the vicinity.
2.
Pair your PC with the device – you do this by adding the device to a list of paired
devices in your PC.
Search for Bluetooth Devices
In Windows 2000
1.
In the Folders pane of My Bluetooth Places, Double-click Bluetooth→Search for
devices.
2.
Select Entire Bluetooth Neighborhood in the right pane. The device name(s) will
show up if this computer has used the Bluetooth service.
In Windows XP
1.
In the Folders pane of My Bluetooth Places, Double-click Bluetooth→ Search for
devices.
2.
Select Search for devices in range in the left pane. The device name(s) will show up if
this computer has used the Bluetooth service.
- 14 -
Pair
Pairing is the process of associating Bluetooth devices with each other so that they connect as
soon as they get within range of each other.
You can initiate the pairing between two Bluetooth devices from your own PC or you can
accept a request for pairing from the other device.
To initiate pairing with a device
1.
Right click the device that you just found. Select Pair Device.
2.
The Bluetooth Passkey Request screen will be present.
authenticate device identity and encrypt data.
- 15 -
Enter the Passkey to
3.
Meanwhile, the remote device that is requested for connection will prompt you with the
following message for you to enter the passkey. Click the prompted message to enter
the passkey.
4.
Enter a passkey (up to 16 digits) for both your PC and for the other device.
After the pairing procedures are completed, you may start using the local services that a
Bluetooth server is capable of providing, which includes Bluetooth Serial Port, Dial-Up
Networking, Fax, File Transfer, Information Exchange, Information Synchronization and
Network Access.
How to use the service of File Transfer
The File Transfer service allows one Bluetooth device to perform file operations on the
specified or default File Transfer directory (and the folders and files it contains) of another
Bluetooth device.
On the Server PC,
1. From the Bluetooth Configuration panel, on the Information Exchange tab, enter the
directory you want to share the folders with the other device. Click OK.
On the Client PC,
1. In the Folders pane of My Bluetooth Places, select Entire Bluetooth Neighborhood.
- 16 -
2.
In the right pane of Entire Bluetooth Neighborhood, right-click anywhere except on a
device name and select Refresh from the pop-up menu.
3.
In the Folders pane of My Bluetooth Places, right-click the device you already set to
transfer files with and select Discover Available Services from the pop-up menu.
4.
Double-click Public Folder to expand that folder. If there are additional folders inside
the expanded folder then those additional folders may have to be expanded.
- 17 -
CONFIGURATION
General
You may determine the device properties and basic system security settings on the General
tab of the Bluetooth Configuration Panel.
Identity
Computer Name
Computer type
Enter a unique name to identify this computer to other Bluetooth
devices in the vicinity; this field cannot be left blank.
Select either Desktop or Laptop from the drop-down menu to
help identify this computer to other Bluetooth devices in the
vicinity.
Security1
High
Requires Bluetooth devices to authenticate (enter a Personal Identification
Number (PIN) before allowing a connection to be established. Your computer
and the connected Bluetooth device will exchange data using encrypted links.
Medium The default setting—security is configured at the service-level. Service level
security means that each individual service must have its security settings
(Authentication, Authorization and Encryption) set independently.
1 If the security mode is “Medium” and service-level security is not configured, any Bluetooth device will be able to
discover your computer and use its services.
- 18 -
Accessibility
In the Accessibility tab of the Bluetooth Configuration Panel, you will be able to specify
which remote devices may access this computer.
Security settings configured in the General, Local Services, and Client Applications tabs
may also affect which devices have access to this computer.
To allow other devices to discover this computer: select "Let other Bluetooth devices
discover this computer" to permit remote Bluetooth devices to find and report this computer.
If "Allow No devices to connect" (below) is selected, this option is not available.
- 19 -
From the Allow drop-down-menu, you may select to control the types of devices that are
allowed to connect to this computer.
No devices to connect
no remote devices are permitted to initiate a connection with
this computer. However, this computer can still initiate
connections (as a client) with remote Bluetooth devices.
all remote devices are permitted to connect to this computer.
All devices to connect
Only paired devices to only devices that have been paired with this computer are
allowed to connect to it.
connect
Only devices listed below to only the listed devices are allowed to connect to this computer
(see next section for details of adding and deleting devices).
connect
- 20 -
Discovery
In the Discovery tab of the Bluetooth Configuration Panel, you can determine:
1.
whether your computer looks for other Bluetooth devices automatically,
2.
how often it looks and,
3.
what type of devices it looks for.
Perform a periodic Search for Devices
When "Look for other Bluetooth devices" is selected, BTW automatically searches for
devices every “X” minutes. X is an integer from 1 to 60. To change the time between auto
inquiries, highlight the existing time and enter the new time.
Note: When My Bluetooth Places is first opened it performs an initial automatic search for
devices even if "Look for other Bluetooth devices" is not enabled.
Determine which devices will be reported
BTW can screen out devices that you do not need to access.
The options are:
Report all Bluetooth devices
Report only selected Bluetooth devices
Select the desired option from the drop-down list.
- 21 -
Information Exchange
The Information Exchange service provides a way to send and receive Microsoft Outlook
items to and from another Bluetooth device like a Personal Digital Assistant or notebook
computer.
The settings on the Information Exchange tab of the Bluetooth Configuration Panel are used
to configure:
File Transfer
My Shared Directory: the directory configured in this section is the highest-level directory
to which a remote Bluetooth computer has access. This directory and its sub directories are
displayed in the remote device's My Bluetooth Places.
Click the Browse button and navigate to the directory that will be used as My Shared
Directory.
Send Business Card
My Business Card: the path to the directory on this computer that contains your electronic
business card.
Select the "Send Business Card on Request" option to allow remote devices to obtain your
business card.
Click the Browse button and navigate to the directory that contains your business card.
Receive Business Card
My Inbox Directory: the path to the directory on this computer where inbound Personal
- 22 -
Information Manager items such as Business cards, Notes, Calendar entries and Email
Messages will be saved.
Select the types of items you wish to accept by placing a checkmark in the appropriate boxes,
and then click the Browse button to navigate to the directory where they should be saved.
Select the "Save Objects in Personal Information Manager" option to save incoming objects
directly in the PIM. When this option is selected, the path specified in “My Inbox Directory”
is not used.
- 23 -
Local Services
The settings on the Local Services tab of the Bluetooth Configuration Panel determine the
configuration of the services provided by your computer to remote devices. Each service can
be configured individually for security, name, and other settings.
The Local Services tab also includes options to add and delete user-defined serial services.
BTW Local Service names are:
Bluetooth Serial Port
Dial-Up Networking
Fax
File Transfer
Information Exchange
Information Synchronization
Network Access
- 24 -
Client Application
Network Access
The Network Access service permits a Bluetooth client to use a Local Area Network
connection that is physically attached to another Bluetooth device (the server).
Possible Network Access servers include:
1.
Bluetooth-enabled computers that have a hardwired Ethernet connection.
2.
Stand-alone Bluetooth Network Access Points.
The Bluetooth server must be specifically configured to provide the Network Access service.
After a Bluetooth device is configured as a Network Access server it cannot act as a Network
Access client without being re-configured.
- 25 -
Hardware
The Hardware tab of the Bluetooth Configuration Panel provides basic information about the
Bluetooth hardware installed on this computer and access to the Advanced Settings dialog
box.
Devices:
Name
Type
name of the device, e.g., My Bluetooth Device
type of the device, e.g., USB.
Device Properties:
the name of the company that manufactured the device selected in the
Manufacturer
Devices section of this dialog box.
Firmware
Revision
the manufacturer's firmware version number.
Device Status
indicates that the device is operating properly or that there is a
problem/conflict.
Device Address
the Bluetooth Device Address (BDA or BD_Addr) programmed into this
device when it was manufactured.
HCI Version
the version number of the Bluetooth Specification that the Host
C
ll
f
li
ih
- 26 -
Controller Interface complies with.
HCI Revision
the revision number of the Bluetooth Specification that the Host
Controller Interface complies with.
LMP Version
the version number of the Bluetooth Specification that the Link Manager
Protocol complies with.
LMP
Version
Sub the sub-version number of the Bluetooth Specification that the Link
Manager Protocol complies with.
Advanced
displays the Advanced Settings dialog box, which allows you to select the
country code and transmission power settings. This option is not available on all systems
.
Hardware Advanced Settings Dialog Box
When available, this dialog box is reached from the Hardware tab of the Bluetooth
Configuration Panel.
Depending on the country in which the hardware is sold and/or in which it will be used, the
Advanced button may not be present.
From this dialog box you can set the:
Country Code:
Maximum Transmission Power:
North America, Europe (except France), and
Japan
France and China
High
Medium
Low
Click the Apply button to implement the changes. A dialog box appears with
notification that the Bluetooth device attached to this computer must be reset before the
change(s) will take effect.
Click the Yes button to reset the Bluetooth device now—all open Bluetooth connections
will be closed.
Click the No button to save the changes—the changes will be applied the next time the
Bluetooth device is reset or restarted.
- 27 -
Version Info
The Version Info tab of the Bluetooth Configuration Panel displays the name and version
number of the software components of BTW.
There are no options to configure on this tab.
- 28 -
Notifications
The Notifications tab of the Bluetooth Configuration Panel lets you associate a sound
(Windows *.wav file) with specific Bluetooth events.
Sounds can be associated on an individual basis with several events, including:
1.
When a PIN code is required
2.
When a remote device attempts to access:
Files on this computer
A Bluetooth port
The Dial-up network service
The LAN Access service
The Fax service.
3.
When a remote device attempts to send:
Synchronization information.
Information items
To associate a sound with a Bluetooth event:
1. From the Bluetooth Configuration Panel, select Notifications tab.
2. In the Notify column of the Events list, select the check box associated with the event.
3. In the Sound area of the Notifications tab, click the Browse button and navigate to the
sound file (*.wav) to be used for notification. To preview the sound file, click the play (>)
button.
- 29 -
4. Click the OK button to close the Bluetooth Configuration Panel.
Note: The sound will not play, even though it has been assigned, unless the Notify check box
is selected.
- 30 -
TROUBLESHOOTING
CANNOT CONNECT TO A PAIRED DEVICE:
Paired devices are always displayed in My Bluetooth Places, even if the remote device is
out of range or not powered up.
Verify that the remote member of the pair is within radio range and powered up and then
attempt the connection again.
CANNOT DISCOVER SERVICES ON AN UN-PAIRED REMOTE DEVICE:
The remote device may not be powered up or may be out of range.
Verify that the remote device is powered up.
Verify that the remote device is in Connectable mode (Bluetooth Configuration Panel >
Accessibility tab).
Perform a Search for Devices to verify that the device is within range.
DIAL-UP NETWORKING SERVICE DOES NOT START:
The Dial-up Networking service will not start unless a properly configured modem is
attached to the server.
Verify that the modem is usable as a local device from the server.
In the Bluetooth Configuration Panel, Local Services tab, double-click the Dialup
Networking service:
Click the down arrow in the Modem field and select the modem that will be used to
dial out
Click the OK button
Click the OK button to close the Bluetooth Configuration Panel.
HOW DO I DETERMINE THE BLUETOOTH DEVICE ADDRESS (BDA) OF MY
HARDWARE DEVICE?
In the Bluetooth Configuration Panel, on the Hardware tab, in the Devices section, select
the device you want to determine the address of. In the Device Properties section of the
dialog box, the fourth entry, Device Address, is the BDA of the selected Bluetooth
HOW DO I DETERMINE THE VERSION NUMBER OF THE BLUETOOTH
SPECIFICATION THAT THE HOST CONTROLLER INTERFACE (HCI)
COMPLIES WITH?
- 31 -
In the Bluetooth Configuration Panel, on the Hardware tab, in the Device Properties
section, the fifth entry provides Bluetooth Specification compliance information for the
Host Controller Interface.
The sixth entry contains the Specification Revision information for the Host Controller
Interface, if appropriate.
HOW DO I DETERMINE THE VERSION NUMBER OF THE LINK MANAGER
PROTOCOL (LMP)?
In the Bluetooth Configuration Panel, on the Hardware tab, in the Device Properties
section, the seventh entry provides Link Manager Protocol version number information.
The eighth entry contains the Link Manager Protocol sub-version number information, if
appropriate.
HOW DO I FIND INFORMATION ABOUT THE BLUETOOTH HARDWARE
ATTACHED TO MY COMPUTER?
In the Bluetooth Configuration Panel, select the Hardware tab
HOW DO I TEST A NETWORK ACCESS CONNECTION?
If the client is hardwired to the LAN, unplug the hardwired connection to ensure that the
test checks the wireless connection rather than the hardwired connection.
If the server has access to the Internet, open a browser on the client and connect to the
World Wide Web.
You may also Ping the server from the DOS prompt.
WHY DO I GET AN UNKNOWN PORT MESSAGE WHEN I ATTEMPT TO USE A
BLUETOOTH SERIAL PORT?
The “Unknown Port” error message usually means an attempt was made to connect a port
that was in use.
Additional Bluetooth Serial Ports can be added if they are required.
- 32 -