WV-CP474 - Panasonic Canada

WV-CP474 - Panasonic Canada
Color CCTV Cameras
WV
Operating Instructions
-CP
470
Model No.
WV-CP470
WV-CP474
(Lens: Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N1101-2042
V8QA5915CN
Printed in Japan
N 19
For U.S.A
CP4
70
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SA 1965
SA 1966
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence
of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
The exclamation point within
an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense.
FCC Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or
peripheral devices). Any changes or modifications not expressly approved by the party
responsible for compliance could void the
user’s authority to operate this equipment.
The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
PREFACE
Panasonic's WV-CP470 (WV-CP474) series color digital camera introduces a new level of
high picture quality and high resolution through the use of a 1/3-inch interline transfer CCD
image sensor having 771 horizontal pixels (picture elements), and digital signal processing
LSIs. This model offers cutting-edge technology for advanced video surveillance.
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Ask a qualified service personnel for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged
by improper handling or storage.
3. The following installation should be made by qualified service personnel or
system installers.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a
mild detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the specified temperature, humidity or power
source ratings.
Use the camera at temperatures within –10 °C to +50 °C (14 °F - 122 °F), and humidity
below 90 %. The input power source is 120 V AC 60 Hz for WV-CP470 and DC 12 V/AC
24 V for WV-CP474.
Caution:
To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the DC 12 V or AC 24 V Input Terminal.
FEATURES
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB.
(3) Various External Sync Functions, including Gen-Lock
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3. Minimum Illumination of 0.8 lx (0.08 foot-candle) at color mode, 0.1 lx (0.01 foot-candle)
at black and white mode with F1.4 lens.
4. 480 lines of horizontal resolution
5. High quality picture:
(a) 2H type vertical enhancer for greater picture sharpness
(b) Chroma averaging circuit for better color signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
6. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC)
function.
7. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
8. Built-in Digital Motion Detector
9. Auto black-and-white mode enables the camera to switch between color and blackand-white picture in response to light input.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q
we
r
!2
!3
GEN-LOCK
VIDEO OUT
WV-CP470
AC 120V 60Hz
POWER
WV –CP470
ALARM
DAY/
NIGHT
!7
t
!1
!2
!3
GEN-LOCK
VIDEO OUT
WV-CP474
i
Hi-Z G/L 75Ω
GND
o
y
1
POWER
!8
2
ALARM
AC 24V IN
DC 12V IN
u
!4
!5
!6
GND
OUT
GND
IN
DAY/
NIGHT
GND
OUT
GND
IN
!4
!5
!6
!0
Slide the panel to the left until it locks.
q Auto Iris Lens Connector
Connects the auto iris lens with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100).
w Flange-back Adjusting Ring
Adjusts the back focal length and picture focus.
e Flange-back Fixing Screw
r Lens (Option)
t Camera Mounting Screw Hole
Mounts the camera onto a mounting bracket.
y Down Button (K)
Moves the cursor downward and selects items in the CAM SET UP menu.
u Left Button (L)
Moves the cursor to the left, selects the mode and adjusts some levels.
i Up Button (J)
Moves the cursor upward and selects items in the CAM SET UP menu.
o Right Button (M)
Moves the cursor to the right, selects the mode and adjusts some levels.
!0 Set Button (I)
Activates an item selected in the CAM SET UP menu.
!1 Gen-lock Termination Switch (Hi-Z, G/L 75 Ω)
Set this switch to Hi-Z when a gen-lock video input signal is looped through. In all other
cases, set this switch to 75 Ω.
!2 Gen-lock Input Connector (GEN-LOCK)
Connects an external system for synchronization.
!3 Video Output Connector (VIDEO OUT)
Connects the VIDEO IN connector of the monitor.
!4 Power Indicator (POWER)
!5 Alarm Output Terminal (ALARM OUT/GND)
Connects to the alarm input connector (terminal) of an external device. When the camera detects motion, the alarm output signal is supplied to the connected external device
(Open collector output: 16 V DC, 100 mA max).
!6 Day/Night Input Terminal (DAY/NIGHT IN/GND)
This terminal is used for connecting the camera to an external day/night detecting sensor.
!7 AC Inlet Socket
Plug the power cord (supplied as a standard accessory) into this socket and connect it
to an AC outlet.
!8 AC/DC Compatible Input Terminal
(DC 12 V IN/AC 24 V IN)
This terminal is for connecting the 12 V DC or 24 V AC power supply cord.
Note: Do not exceed the ratings of the voltage or current when connecting the external
device.
Cautions:
1. Connect to 12 V DC (10.8 V - 16 V) or 24 V AC (19.5 V - 28 V) class 2 power supply
only. Be sure to connect the grounding lead to the GND terminal when the power is
supplied from a 24 V AC power source.
2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
CONNECTIONS
A. WV-CP470 (120 V AC 60 Hz)
Plug the AC power cord (supplied as standard accessory) into the AC inlet socket and connect it to a 120 V AC 60 Hz outlet.
Notes:
• Connect the power cord firmly.
• The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may be pulled off the camera when the
camera pans or tilts.
B. WV-CP474 (12 V DC/24 V AC)
The WV-CP474 has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power
supply cord can be connected to this terminal. The camera detects the power source automatically.
1. 12 V DC Power Supply
Connect the power cord to the AC/DC compatible input terminal on the rear panel of the
camera.
Resistance of copper wire [at 20 °C (68 °F)]
GND
12 V DC
(10.8 V - 16 V)
1
1
2
2
Copper wire
#24
#22
#20
#18
size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
AC 24V IN
DC 12V IN
Resistance
Ω/m
0.078
0.050
0.030
0.018
Resistance
Ω/ft
0.026
0.017
0.010
0.006
• Calculation of maximum cable length between camera and power supply
10.8 V DC ≤ VA - (R x 0.42 x L) ≤ 16 V DC
L : Cable length (m)
R : Resistance of copper wire (Ω/m)
VA : DC output voltage of power supply
unit
VA − 12
L standard =
0.42 x R
VA − 16
L minimum =
0.42 x R
VA − 10.8
L maximum =
0.42 x R
(m)
(m)
(m)
2. 24 V AC Power Supply
Connect the power cable to the AC/DC compatible input terminal on the rear panel of
the camera.
24 V AC, 60 Hz
(19.5 V - 28 V)
GND
GND
1
1
2
2
AC 24V IN
DC 12V IN
Recommended wire gauge sizes for 24 V AC line.
Copper wire
size (AWG)
#24
#22
#20
#18
(0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
Length
(m)
of Cable
(Approx.) (ft)
95
150
255
425
314
495
842
1 403
Caution:
To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007).
Video Cable
1. It is recommended to use a monitor
whose resolution is at least equal to
that of the camera.
2. The maximum extensible coaxial
cable length between the camera
and the monitor is shown in the
table.
Type of
coaxial cable
Recommended (m)
maximum
cable length
(ft)
RG-59/U RG-6U RG-11/U RG-15/U
(3C-2V) (5C-2V) (7C-2V) (10C-2V)
250
500
600
800
825
1 650
1 980
2 640
Alarm Connections
1. Connect an external sensor to the DAY/NIGHT terminal.
2. Connect an external device such as a buzzer or lamp to the ALARM terminal.
• The alarm output terminal is an open collector terminal with a capacity of 16 V DC, 100
mA or less.
OFF: Open contact
ON: 100 mA or less
• Color/black-and-white input terminal with a capacity of 5 V DC pull-up input, 0.2 mA or
more.
OFF: Open contact
ON: Closed contact
Notes:
• Use a relay unit if the voltage or current of the connected device exceeds the ratings.
• To validate the Day/Night function, set BW mode to EXT on the special menu.
MOUNTING LENS/FOCUS ADJUSTMENT
Installation of Auto Iris Lens Connector
Install the lens connector (YFE4191J100) when using a video drive ALC lens.
(1) Cut the iris control cable at the edge of the lens connector to remove the existing lens
connector and then remove the outer cable cover as shown in the figure below.
The pin assignment of the lens connector is as follows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 0.7 V[p-p]/40 kΩ
Pin 4: Shield, ground
Rib
Pin 3
(2) Solder the lens cable to the pins of the
supplied connector.
Pin 1
Pin 4
Pin 2
Caution for Mounting the Lens
Follow the indication shown in the figure for the protrusion between a lens and the camera
body. This camera wears mount for use with the CS-mount lens at the factory shipment.
Use the supplied C-mount adapter when using the C-mount lens.
The lens less than 450 g (0.99 lbs) can be mounted on the camera. If the lens is heavier,
both the lens and camera should be
secured by the supporter.
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
Mounting the Lens
Note: Before you mount the lens, loosen the screw on the side of the camera, and rotate the
ring clockwise until it stops.
If the ring is not at the end, the inner glass or CCD image sensor may be damaged.
1. Mount the lens by turning it clockwise on the lens mount of the camera.
Note: When mounting the C-mount
lens on the camera, mount the
C-mount adapter by turning it
clockwise in advance.
2. Connect the lens cable to the auto
iris lens connector on the side of
the camera.
Lens Mount
C-mount Adapter
WV
-C
P47
0
Flange-back
Fixing Screw
Flange-back
Adjusting Ring
Flange-back Adjustment
1. Loosen the flange-back fixing screw on the flange-back adjusting ring.
2. Turn the flange-back adjusting ring to obtain a focused point while watching the monitor
screen.
3. Tighten the flange-back fixing screw on the flange-back adjusting ring.
Caution: Tightening the screw by force will cause damage to the screw or deviation of
focus.
CP4
70
Note: The object may be out of focus when using a source of near-infrared light than
using the visible light.
INSTALLATION OF CAMERA
• Mounting from the Top
Remove the mount adapter from the bottom of the camera by removing the two fixing
screws. Attach the mount adapter to the top as shown in the figure, then mount the
camera on the mounting bracket.
Make sure that the two original fixing
screws are used when mounting the
mount adapter as longer length screws
may damage inner components, or
shorter type screws may cause the
camera drop.
Fixing Screws
Mount Adapter
WV
-C
P47
0
SETUP
1. CAMERA SETUP MENU
This camera utilizes an on-screen user setup menu.
• Opening the Setup Menu
Press and hold down I for 2 seconds or
more.
Highlighted
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON(DNR-H)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LENS DRIVE
DC
↵
The CAM SET UP menu appears on the
monitor as shown in the figure.
Check the current settings on the menu.
END
SET UP DISABLE
Refer to the following sections for a detailed
description of menu items. If you decide not to make any changes after checking the current settings, move the cursor to END in the bottom line, and press I to close the setup
menu.
Note: If no button is pressed for 6 minutes while any of the setup menu is being displayed
on the monitor screen, it is automatically closed and the mode returns to the normal
camera picture.
2. SETUP OPERATION
This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the
CAM SET UP menu, use the following buttons on the side panel.
Up
Button
Left Button
Right
Button
Set Button
Down
Button
Up Button (J):
Moves the cursor upwards. Use this button to select an item or adjust
the parameters.
Down Button (K): Moves the cursor downwards. Use this button to select an item or
adjust the parameters.
Right Button (M): Moves the cursor to the right. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Left Button (L):
Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Set Button (I:
Executes selections and displays a submenu for an item with the N
mark.
• To reset the parameter to the factory default setting, move the cursor to the parameter
to be reset and press L and M simultaneously.
• To return to the previous menu or page, move the cursor to RET and press I.
• To close the setup menu, move the cursor to END and press I.
• All Reset Operation
All reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both L and M, press I for a few seconds. The message ALL
RESET momentarily appears on the monitor screen.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot change the currently active settings. This is to prevent accidental changing of the
settings.
END
SET UP DISABLE
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON(DNR-H)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LENS DRIVE
DC
↵
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON(DNR-H)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LENS DRIVE
DC
↵
To edit the CAM SET UP menu (change
settings), press J and K or L and
M to move the cursor to SET UP DISABLE in the bottom line.
Press I. SET UP DISABLE changes to
SET UP ENABLE. Move the cursor to
END, then to the item(s) you want to
change.
END
SET UP ENABLE
Important Notice:
When the setup menu is closed after changing the parameters in the menu, the new
values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only
Memory). These values remain valid until new values are stored, even if the power of
the camera is off.
SETTING PROCEDURES
1. Camera Identification (CAMERA ID) Setting
You can use the camera identification (CAMERA ID) to assign a name to the camera. The
camera ID consists of up to 16 alphanumeric characters. The camera ID display can be
switched on or off on the monitor screen.
To edit the CAMERA ID
1. Move the cursor to CAMERA ID.
The factory default setting is OFF.
2. Press I. The CAMERA ID menu
appears. The cursor on the letter “0” is
highlighted.
Character Cursor
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
3. Move the cursor to the character you
want to edit by pressing L/M/J/
K.
4. After selecting the character, press I.
The selected character appears in the
editing area. (The pointer in the editing
area moves to the right automatically at
this moment.)
Character
Area
SPACE
POSI RET END RESET
................
Pointer
Command
Editing
Area
CAMERA ID menu
5. Repeat the steps above until all characters are edited.
To enter a blank space in the CAMERA ID
Move the cursor to SPACE and press I.
To replace a specific character in the CAMERA ID
1. Move the cursor to the editing area by pressing K.
2. Move the pointer to the character to be replaced by pressing L or M. Then move
the cursor to the character area and select a new character.
3. Press I to determine the CAMERA ID.
To clear all characters in the editing area
Move the cursor to RESET and press I. All characters in the editing area disappear.
To determine the display position of the CAMERA ID
1. Move the cursor to POSI, and press I. The display in the figure appears and the
CAMERA ID is highlighted.
Highlighted
2. Move the CAMERA ID to the desired position by pressing L/M/J/K.
3. Press I to fix the position of the CAMERA ID. The mode returns to the previous
CAMERA ID menu.
WV-CP470
Notes:
• The CAMERA ID stops at the edges of the monitor screen.
• The CAMERA ID moves faster if any of L/M/J/K is kept pressed for a second or more.
2. Light Control Setting (ALC/ELC)
You can select the mode for adjusting the lens iris.
ALC: If you use the auto iris lens, select this parameter.
ELC: If you use a fixed or manual iris lens, select this parameter.
The factory default setting is ALC.
1. Move the cursor to ALC/ELC.
2. Select ALC or ELC.
Cautions:
1. Under bright lighting conditions such as outdoors, use an ALC type lens because the
ELC control range is not wide enough under these conditions.
2. Use an ALC type lens if the following phenomena occur:
• Strong smear and/or blooming on highlight objects such as spotlight or sunlight
from windows.
• Noticeable flicker in the picture and/or color rendition variations.
3. If ELC is selected, SUPER-D2 and SHUTTER are not available and white balance mode
is automatically set to ATW1 or ATW2 previously set.
4. If ELC is selected for ALC/ELC and used with the fixed iris lens in, the focal depth
becomes shallower than with the ALC type lens. Therefore, the range of focus-to-object
distance becomes narrower.
2-1. ALC Mode with SUPER-D2 ON
Super Dynamic2 Function (SUPER-D2)
The important object in a scene is usually placed in the center of the monitor screen. In the
SUPER-D2 mode, more photometric weight is given to the center of the screen (where the
important object is located) than to the edge of the screen (where a bright backlight would
most likely be located). You can use the SUPER-D2 function if you select ALC. It eliminates
interference by strong background lighting which makes the camera picture dark, such as a
spotlight.
1. Select ALC, and press I. The ALC
CONT menu appears.
2. Move the cursor to SUPER-D2 and
select ON.
** ALC CONT **
BACK LIGHT COMP
SUPER-D2
ON
LEVEL
...I.....
+
RET
END
3. If you want to adjust the video output level, move the "I" cursor for LEVEL. Adjust to the
desired level by pressing L or M.
(To be continued reverse page)
SETTING PROCEDURES
2-2. ALC Mode with SUPER-D2 OFF and ELC Mode
Note: If ELC is selected, set MASK SET according to this procedure.
1. Move the cursor to SUPER-D2 and
select OFF. (When you select ELC,
SUPER-D2 is not available.) The MASK
SET appears on the menu.
** ALC CONT **
BACK LIGHT COMP
MASK SET
OFF
↵
SUPER-D2
LEVEL
2. Move the cursor to MASK SET and
press I. The 48 mask areas appear
on the monitor screen. The cursor is
blinking in the upper left corner of the
screen.
RET
END
Blinking
3. Move the cursor to the area where
backlight is bright and press I to
mask that area. The mask turns to
white. (When the cursor is moved on
an area that has already been masked,
the mask and cursor start blinking.)
4. Repeat step 3 to mask the desired
area. To cancel masking, move the
cursor to that area and press I.
5. After masking is completed, press I
for 2 seconds or more. The ALC CONT
menu appears.
6. If you want to change the video output
level (picture contrast), move the “I”
cursor for LEVEL and adjust the level.
...I.....
+
Blinking
Turns to white
Blinking
Note: If ON is selected for SUPER-D2, a shadow (black line) may appear at the boundary
between the bright and the dim scene. This is a natural phenomenon and does not indicate trouble.
3. Shutter Speed Setting (SHUTTER)
Note: When ELC is selected for ALC/ELC on the CAM SET UP menu or ON is selected for
SUPER-D2 on the ALC CONT menu, this item is not available.
To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu.
Move the cursor to SHUTTER and select the electronic shutter speed.
The preset values for SHUTTER (electronic shutter speed) change by pressing L or M
as follows:
The factory default setting is ---.
OFF (1/60)
1/10000
1/100
1/4000
1/250
1/500
1/2000
1/1000
4. Gain Control Setting (AGC ON (DNR-H, DNR-L)/OFF)
AGC (Automatic Gain Control) automatically controls the gain (an image brightness level).
Move the cursor to AGC and select automatic level adjustment ON (DNR-H), ON (DNR-L), or
OFF. The factory default setting is ON (DNR-H).
ON (DNR-H): This setting raises the gain and brightens the image under low light conditions.
ON (DNR-L): This setting reduces an afterimage sometimes caused by a moving object
when ON (DNR-H) is activated.
OFF: This setting does not control the gain.
Notes:
• When ON (DNR-L) is selected, noise can slightly increase than ON (DNR-H).
• DNR-H and DNR-L do not appear on the system status display of the connected equipment.
5. Electronic Sensitivity Enhancement (SENS UP)
There are two modes for SENS UP.
AUTO: If you select X10 AUTO, for example, the sensitivity is automatically raised to
X10 max. When AUTO is selected, AGC is automatically set to ON.
FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32.
The factory default setting is OFF.
Move the cursor to SENS UP and select the parameter for electronic sensitivity enhancement.
The preset values for SENS UP (electronic sensitivity enhancement) change by pressing
L or M as shown right:
OFF
X32 FIX
X2 AUTO
X16 FIX
X4 AUTO
X10 FIX
X6 AUTO
X6 FIX
X10 AUTO
X4 FIX
OFF
X2 FIX
Notes:
• When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this
item.
• When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has
priority so that the SUPER-D2 function is not activated automatically.
• While the SENS UP function is selected, noise, spots or a whitish phenomenon may
appear in the picture when the sensitivity of the camera is increased. This is a normal
phenomenon.
6. Synchronization Setting (SYNC)
You can select internal sync (INT) mode or line-lock (LL) mode. Additionally, this model
accepts the VBS signal (composite color video or blackburst signal) and VS signal (B/W
composite video or composite sync signal). The VD2 signal (multiplexed vertical drive signal) with the composite video output signal from external equipment such as a matrix
switcher is also acceptable.
Whenever the VD2 signal is supplied to this camera, the camera automatically switches to
the VD2 sync mode.
1. Move the cursor to SYNC and select LL or INT.
The factory default setting is INT.
2. Press I.
If LL is selected, the SYNC menu appears. (If INT is selected, the synchronization mode
is automatically set to internal sync pulse, and the menu is not displayed.)
Important Notices:
1. The priority for the sync modes is as follows:
1. Multiplexed vertical drive (VD2) (Highest priority)
2. Line-lock (LL)
3. Composite color video or blackburst signal (VBS)
4. Composite B/W video or composite sync signal (VS)
5. Internal sync (INT) (Lowest priority)
2. When the internal sync mode is to be used, select INT. No gen-lock input signal should
be supplied to the GEN-LOCK connector on the rear panel.
3. Whenever the multiplexed vertical drive pulse (VD2) is supplied to the camera from an
external equipment such as a matrix switcher, the camera sync mode is automatically
switched to the VD2 mode.
4. When the VBS or VS gen-lock mode is to be used select INT from this menu and supply
the gen-lock input signal to the GEN-LOCK connector on the rear panel.
5. The VBS gen-lock mode has a submenu for horizontal and subcarrier phase adjustments. When the cable length of the video output or the gen-lock input is changed, the
horizontal and subcarrier phase must be re-adjusted.
6. The VS gen-lock mode has a submenu for horizontal phase adjustments. When the
cable length of the video output or the gen-lock input is changed, the horizontal phase
must be re-adjusted.
7. The line-lock mode has a submenu for line-lock vertical phase adjustment. If the camera installation is relocated, check the vertical phase adjustment again since the AC
line phase may be different.
6-1. VBS Gen-lock Mode [EXT (VBS)]
↵
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON(DNR-H)
SENS UP
OFF
SYNC
EXT(VBS)
WHITE BAL
ATW1
MOTION DET
OFF
LENS DRIVE
DC
↵
1. Move the cursor to SYNC and select
INT.
2. Connect the coaxial cable for the
blackburst or composite color video
signal to the gen-lock input connector.
3. Confirm that INT changed to EXT (VBS)
on the menu.
Note: The gen-lock input signal should
meet EIA RS-170A specifications
and should not contain jitter, such
as a VCR playback signal, as it
could disturb synchronization.
END
SET UP ENABLE
** SYNC **
H PHASE
........I
+
SC COARSE
1(1--4)
4. After confirming that the cursor is on
EXT (VBS), press I. The phase
SC FINE
....I....
+
adjustment menu appears on the monitor screen.
RET END
5. Supply the video output signal of the
camera to be adjusted and the reference gen-lock input signal to a dualtrace oscilloscope.
6. Set the oscilloscope to the horizontal rate and expand the horizontal sync portion on the
oscilloscope.
7. Move the cursor to H PHASE.
8. Adjust the horizontal phase by pressing L or M. The adjustable range is 0-2.0 µs.
9. Move the cursor to SC COARSE.
10. Press L or M to match the chroma
phase of the camera’s video signal,
1 (1 - - 4): 0 degrees
when observed at the output of the
special effect generator (SEG) or
2 (1 - - 4): 90 degrees
switcher, as closely as possible to the
color of the original scene. (SC
3 (1 - - 4): 180 degrees
COARSE adjustment can be incremented in steps of 90 degrees (4 steps) by
4 (1 - - 4): 270 degrees
pressing L or M.)
Note: After the fourth step, the adjustment returns to the first step.
11. Move the cursor to SC FINE.
12. Press L or M to match the color (hue) of the camera’s video signal, when observed
at the output of the special effect generator (SEG) or switcher, as closely as possible to
the color of the original scene.
The SC FINE adjustment has a range of 90 degrees of color shift.
Notes:
• When the “I” cursor reaches the “+” end, it jumps back to “–” . At the same time,
SC COARSE is incremented by one step to enable a continuous adjustment. The
reverse takes place when the “I” cursor reaches the “–” end.
• When L or M is kept pressed for a second or more, the “I” cursor moves faster.
• For more accurate adjustment, supply both the original camera video output signal
and the effect output video signal (program output video signal) of the special
effect generator (SEG) to a vectorscope and compare the chroma phase of both
signals.
• To reset SC COARSE and SC FINE to the values preset at the factory, press L
and M simultaneously.
6-2. VS Gen-lock Mode [EXT (VS)]
↵
↵
↵↵
1. Move cursor to SYNC and select INT.
** CAM SET UP **
2. Connect the coaxial cable for the comCAMERA ID
OFF
ALC/ELC
ALC
posite sync or composite B/W video
SHUTTER
--signal to the GEN-LOCK connector.
AGC
ON(DNR-H)
SENS UP
OFF
3. Confirm that INT changed to EXT (VS)
SYNC
EXT(VS)
WHITE BAL
ATW1
on the menu.
MOTION DET
OFF
LENS DRIVE
DC
Note: The gen-lock input signal should
meet EIA RS-170 specifications
END
SET UP ENABLE
and should not contain jitter, such
as a VCR playback signal, as it could disturb synchronization.
4. After confirming that the cursor is on EXT (VS), press I. The phase adjustment menu
appears on the monitor screen.
5. Supply the video output signal of the
camera to be adjusted and the reference gen-lock input signal to a dualtrace oscilloscope.
6. Set the oscilloscope to the horizontal
rate and expand the horizontal sync
portion on the oscilloscope.
7. Move the cursor to H PHASE.
8. Adjust the horizontal phase by pressing L or M. The adjustable range is
0-2.0 µs.
** SYNC **
H PHASE
RET
........I
+
END
6-3. Line-lock Sync Mode (LL)
1.
2.
3.
4.
5.
6.
Note: The line-lock (LL) sync mode is not available when the camera operates on DC
power.
Move the cursor to SYNC and select LL.
Note: The settings in this menu can be made only when the multiplexed vertical drive
signal (VD2) is not supplied to the
** SYNC **
camera.
After confirming that the cursor is on
V PHASE
LL, press I. The vertical phase
COARSE
1(1--16)
adjustment menu appears on the moniFINE
I........
+
tor screen.
Supply the video output signal of the
RET END
camera to be adjusted and the reference camera video output signal to a
dual-trace oscilloscope.
Set the oscilloscope to the vertical rate and expand the vertical sync portion on the
oscilloscope.
Move the cursor to COARSE. The cursor is highlighted.
Press L or M to match the vertical phase for both video output signals as closely as
possible. (COARSE adjustment can be incremented in 16 steps by 22.5 degrees by
pressing L or M.)
Note: After the sixteenth step, the adjustment returns to the first step.
7. Move the cursor to FINE.
1 (1 - - 16): 0 degrees
8. Press L or M to match the vertical
2 (1 - - 16): 22.5 degrees
phase for both video output signals as
closely as possible.
(FINE adjustment can be made by up
16 (1 - - 16): 337.5 degrees
to 22.5 degrees by pressing L or
M.)
Notes:
• When the “I” cursor reaches the “+” end, it jumps back to “–”. At the same time,
COARSE is incremented by one step to enable a continuous adjustment. The
reverse takes place when the “I” cursor reaches the “–” end.
• When L or M is kept pressed for a second or more, the “I” cursor moves faster.
• To reset COARSE and FINE to the values preset at the factory, press L and M
simultaneously. COARSE and FINE adjustments are preset at the factory to zerocrossing of the AC line phase.
• If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of
the camera video output signal may be disturbed.
7. White Balance Setting (WHITE BAL)
7-1. Auto-Tracing White Balance Mode (ATW)
↵
↵↵
You can select one of three modes for white balance adjustment as follows:
The factory default setting is ATW1.
• ATW1 (Auto-Tracing White Balance 1)
Move the cursor to WHITE BAL and
** CAM SET UP **
select ATW1.
CAMERA ID
OFF
In this mode, the color temperature is
ALC/ELC
ALC
SHUTTER
--monitored continuously and thereby
AGC
ON(DNR-H)
white balance is automatically set. The
SENS UP
OFF
SYNC
INT
color temperature range for the proper
WHITE BAL
ATW1
white balance is approximately 2 600 MOTION DET
OFF
LENS
DRIVE
DC
6 000K. Proper white balance may not
be obtained under the following condiEND
SET UP ENABLE
tions:
1. The color temperature is out of the 2 600 - 6 000K range.
2. When the scene contains mostly high color temperature objects, such as a blue
sky or sunset.
3. When the scene is dim.
In these cases, select the AWC mode.
• ATW2 (Auto-Tracing White Balance 2)
Auto-tracing white balance in sodium lamp mode (ATW2)
When you select ATW2 for sodium lamp, white balance is automatically set (no operation needed).
Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup
menu.
1. Move the cursor to WHITE BAL and
select AWC → PUSH SW.
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON(DNR-H)
SENS UP
OFF
SYNC
INT
WHITE BAL
AWC→PUSH SW
MOTION DET
OFF
LENS DRIVE
DC
↵↵
• Automatic White Balance Control
Mode (AWC)
In this mode, accurate white balance is
obtained within a color temperature
range of approximately 2 300-10 000K.
END
Highlighted
SET UP ENABLE
2. Press I to start the white balance
setup. The PUSH SW is highlighted to indicate that the white balance is being set.
3. When the white balance setting is completed, the PUSH SW returns to normal display.
Note: If white balance is not set, the PUSH SW is being highlighted.
**
AWC
R
B
MASK SET
RET
**
....I....
+
....I....
+
END
↵
4. When you want to adjust the white balance manually, press M to select
AWC and press I. The AWC menu
appears on the monitor screen. (When
ATW is selected, pressing I displays the ATW menu.)
Manual Fine Adjustment for AWC (ATW)
You can set the white balance items manually.
1. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2
OFF and ELC mode”.
2. Move the cursor to R.
3. Press L or M to obtain the optimum amount of red gain.
4. Move the cursor to B.
5. Press L or M to obtain the optimum amount of blue gain.
Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and
blue gain.
8. Motion Detector Setting (MOTION DET)
The motion detector detects the moving objects in the scene by monitoring changes in
brightness level. You can select the level of sensitivity for motion detection.
When this camera is connected to a compatible intelligent CCTV system, the camera transmits an alarm signal by multiplexing it with the video signal.
1. Move the cursor to MOTION DET and
select ON.
The factory default setting is OFF.
2. Press I. The MOTION DETECT
menu appears on the monitor screen.
** MOTION DETECT **
....I....
+
DISPLAY MODE
RET
OFF
↵
ALARM
MASK SET
↵
LEVEL
END
3. Move the cursor to MASK SET and press I. MASK SET lets you set 48 mask areas.
To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2
OFF and ELC mode”.
4. Move the cursor to ALARM and select ON or OFF to set the alarm for DISPLAY MODE.
Note: When using the WV-RM70, WV-CU550 series, WV-CU161 or WV-CU360 controller
with this model, select OFF for ALARM.
5. Move the cursor to DISPLAY MODE and press I to see the current setting. The
masks that detect the brightness changes start blinking.
6. To raise detection sensitivity, press I to return to the MOTION DETECT menu.
7. To obtain the optimum detection level, move the “I” cursor to adjust the level.
8. Repeat the procedures above to obtain a satisfactory setting.
Notes:
• When the camera is not used in a Panasonic Intelligent CCTV System, select OFF.
Otherwise, video equipment may malfunction because of the alarm signal misinterpretation for a time code signal.
• The motion detector may malfunction when the lightning equipment continuously turns
on and off, or when ELC mode is selected for ALC/ELC.
• Set MASK SET over the areas where leaves or curtains etc. are swaying.
• Adjust the detection level on the menu to prevent misinterpretation under low light conditions with noise.
• It takes about 0.2 seconds for the alarm signal to reach the VCR’s alarm terminal after
the camera detects the moving object.
• The motion detector is not specifically intended to prevent theft or fire.
9. Lens Drive Signal Selection (LENS DRIVE)
This item is used to select the type of auto iris lens drive signal to be supplied to the lens
from the auto iris lens connector.
1. Move the cursor to LENS DRIVE.
The factory default setting is DC.
2. Select DC if you are using the auto iris lens that requires a DC drive signal.
Select VIDEO if you are using the auto iris lens that requires a video drive signal.
10. Special Menu
↵
↵↵
This menu lets you adjust and set up the video signal of the camera to meet your requirements.
Move the cursor to END in the bottom
** CAM SET UP **
** SPECIAL **
line of the CAM SET UP menu and
CAMERA ID
OFF
UP SIDE DOWN OFF
ALC/ELC
ALC
press L and M simultaneously
CHROMA GAIN ....I....
SHUTTER
--AP GAIN
....I....
AGC
ON(DNR-H)
(holding down L and press M) for 2
PEDESTAL
.I.......
SENS UP
OFF
HUE
.I.......
SYNC
INT
seconds or more. The SPECIAL menu
+
WHITE BAL
ATW1
BW
OFF
MOTION
DET
OFF
appears on the monitor screen.
BURST(BW)
ON
LENS DRIVE
DC
END
SET UP ENABLE
CAMERA RESET /PUSH SW
RET END
10-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)
1. Move the cursor to UP SIDE DOWN.
2. Select ON when you want to turn the picture upside down.
10-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN.
2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust
the chroma level.
10-3. Aperture Gain Setting (AP GAIN)
1. Move the cursor to AP GAIN.
2. While observing the waveform monitor or color video monitor, move the “I” cursor to
adjust the aperture gain level.
10-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL.
2. While observing the waveform monitor or color video monitor, move the “I” cursor to
adjust the pedestal level (black level).
10-5. Chroma Phase (Hue) Setting (HUE)
1. Move the cursor to HUE.
2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust
the hue (chroma phase) level.
10-6 BW
This function lets you automatically switch from color to black-and-white pictures in low light
conditions such as at night.
1. Move the cursor to BW.
2. Select AUTO1, AUTO2, EXT, ON or OFF using L or M.
AUTO1: The camera selects black and white mode if the picture is dark, or color mode
if the picture is bright enough.
AUTO2: Applying AUTO1 may cause malfunction when using a source of near-infrared
light at night because the illuminance changes significantly when switching
between a color picture and a black-and-white picture. This can be prevented by
using the AUTO2 setting to detect the type of light source.
Note: Because the type of light source is detected based on information received
from the CCD image pickup element, an object that is constantly moving or
has the same color as its background may not always be properly recognized.
When choosing the AUTO2 mode, make sure to use a light source having a
wavelength of 800 nm or more.
EXT: Color picture reverts to black-and-white picture when an external day/night
switching signal is received (refer to alarm connections).
ON: Black-and-white mode enabled.
OFF: Color mode enabled.
The factory default setting is OFF.
3. Select AUTO1 or AUTO2 using L or M.
** BW AUTO1 **
4. Press I.
The AUTO1 or AUTO2 menu appears on
LEVEL
HIGH
DURATION TIME .I..
the monitor screen.
S L
5. Move the cursor to LEVEL and select the
illuminance level using L or M.
LOW: Color picture switches to black-andwhite picture at approx.1 lx with F1.4
RET END
lens.
HIGH: Color picture switches to black-andwhite picture at approx.5 lx with F1.4 lens.
The factory default setting is HIGH.
6. Move the cursor for DURATION TIME to set the switching time using L or M.
The following switching times are available:
10s--30s--60s--300s
(S)
(L)
10-7 BURST (BW)
1. Move the cursor to BURST (BW).
2. Select ON or OFF using L or M.
ON: The burst signal is supplied along with the black-and-white composite video signal.
OFF: The burst signal is not output.
The factory default setting is ON.
Notes:
• We recommend that you usually select ON.
• When the camera is used to synchronize the system for external sync, select
ON to prevent a malfunction.
To reset to the factory settings (CAMERA RESET)
1. Move the cursor to CAMERA RESET. The PUSH SW is highlighted.
2. While holding down L and M, press I for 2 seconds or more. The camera is reset
to the factory settings.
SPECIFICATIONS
Pick-up Device:
Scanning Area:
Scanning:
Horizontal:
Vertical:
Synchronization:
Video Output:
Horizontal Resolution:
Signal-to-Noise Ratio:
Dynamic Range:
Minimum Illumination:
Gain Control:
White Balance:
Aperture:
Electronic Light Control:
Super Dynamic2:
Electronic Shutter Speed:
Lens Mount:
ALC Lens:
Ambient Operating Temperature:
Ambient Operating Humidity:
Power Source and
Power Consumption:
Dimensions (without lens):
Weights (without lens):
771 (H) x 492 (V) pixels, Interline Transfer CCD
4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of
1/3” pick-up tube)
525 lines/60 fields/30 frames
15.734 kHz
59.94 Hz
Internal, Line-locked, External (VS/VBS) or
Multiplexed Vertical Drive (VD2) selectable
1.0 V[p-p] NTSC composite 75 Ω/BNC connector
480 lines (C/L), 570 lines (B/W)
50 dB (Equivalent to AGC Off, weight On)
46 dB
0.8 lx (0.08 footcandle) at F1.4 (C/L), 0.1 lx (0.01 footcandle) at F1.4 (B/W)
ON (DNR-H), ON (DNR-L) or OFF (SET UP MENU)
selectable
ATW1, ATW2 or AWC (SET UP MENU) selectable
Set Variable (SET UP MENU)
Equivalent to continuous variable shutter speeds
between 1/60 s and 1/10 000 s
ON or OFF (SET UP MENU) selectable
1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000,1/2 000,
1/4 000, 1/10 000 s selectable
CS-mount (supplied with C-mount adapter)
DC or Video selectable
–10 °C - +50 °C (14 °F - 122 °F)
Less than 90 %
WV-CP470: 120 V AC 60 Hz, 4.8 W
WV-CP474: 24 V AC 60 Hz, 4.3 W
12 V DC, 440 mA
70 mm (W) x 55 mm (H) x 118 mm (D)
2-5/8” (W) x 2-3/16” (H) x 4-5/8” (D)
WV-CP470: 0.46 kg (1 lbs.) (without power cord)
WV-CP474: 0.45 kg (1 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORIES
Body Cap.....................................................................1 pc.
ALC Lens Connector (YFE4191J100)..........................1 pc.
AC Power Cord (only for WV-CP470) ..........................1 pc.
C-mount Adapter .........................................................1 pc.
OPTIONAL ACCESSORIES
Lenses :
WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3
WV-LA908C3, WV-LZ61/10, WV-LZ61/15, WV-LZA61/2, WV-LZ62/2,
WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LZF61/2
Panasonic Security and Digital Imaging Company
A Division of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838
Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 (809)750-4300
2001
© Matsushita Communication Industrial Co., Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement