Multiquip Mikasa MVH306DS2, MVH306DSCPAS Reversible Plate Compactor Operation and Parts Manual
Below you will find brief information for Mikasa MVH306DS2, Mikasa MVH306DSCPAS. These reversible plate compactors are designed for compacting sand, clay, and asphalt. They feature a powerful Yanmar diesel engine and high-frequency vibrations for efficient compaction. Ideal for various applications, including road construction and backfilling.
Advertisement
Advertisement
OperatiOn and parts Manual
series
MOdel MVH306ds2/
MVH306dsCpas
reVersiBle plate COMpaCtOr
(YanMar l70V6GJ1r1aas5 diesel enGine)
Revision #7 (02/04/14)
To find the latest revision of this publication, visit our website at: www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
pROpOSITION 65 WARNING
Diesel engine exhaust and some of
page 2 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
NOTES
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 3
MVH306DS2/MVH306DSCpAS
Reversible plate Compactors
Proposition 65 Warning ........................................... 2
Table Of Contents .................................................... 4
Parts Ordering Procedures ................................. 5-10
Specifications ........................................................ 11
Dimensions ............................................................ 12
General Nformation ............................................... 13
Components .......................................................... 14
Basic Engine .......................................................... 15
Inspection ......................................................... 16-17
Operation .......................................................... 18-23
Maintenance ..................................................... 24-29
Explanation Of Code In Remarks Column............. 30
Suggested Spare Parts ......................................... 31
Compactor Component Drawings
Nameplate And Decals ..................................... 32-33
Vibrating Plate Assembly .................................. 34-35
Base And Engine Assembly ............................. 36-39
Vibrator Assembly ............................................ 40-41
Control Handle Assy. ....................................... 42-45
Hand Pump Assembly ...................................... 46-47
Battery Assembly.............................................. 48-49
Compaction Analyzing System Assembly ........... 50-51
TAblE Of CONTENTS
Yanmar l70V6 Diesel Engine
Electric Device Assembly ................................ 52-53
Cylinder Block Assembly .................................. 54-55
Cylinder Head Assembly .................................. 56-57
Air Cleaner Assembly ....................................... 58-59
Muffler Assembly .............................................. 60-61
Crankshaft And Camshaft Assembly ................ 62-63
Piston Assembly ............................................... 64-65
Lub Oil Pump And Governor Assembly ............ 66-67
Cooling And Starting Device Assembly ............ 68-69
Fuel Injection Pump Assembly ......................... 70-71
Fuel Tank And Fuel Line Assembly .................. 72-73
Starting Motor And Dynamo Assembly ............ 74-75
Tool, Label, And Gasket Assembly ................... 76-77
Terms And Conditions Of Sale — Parts ................ 78
NOTICE
Specifications and part numbers are subject to change without notice.
page 4 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
Best deal!
pARTS ORDERING pROCEDuRES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1 st , 2006
Order via internet (dealers Only) :
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specifi cation Information
If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip.
com.
To obtain an MQ Account, contact your
District Sales Manager for more information.
Goto www.multiquip.com and click on
Order Parts
to log in and save!
Use the internet and qualify for a 5% discount on Standard orders for all orders which include complete part numbers.*
Note: Discounts Are Subject To Change
Order via Fax (dealers Only) :
All customers are welcome to order parts via Fax.
domestic (us) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% discount on Standard orders for all orders which include complete part numbers.*
Note: Discounts Are Subject To Change
Order via phone:
domestic (us) dealers Call:
1-800-427-1244
non-dealer Customers:
Contact your local Multiquip Dealer for parts or call 800-427-1244 for help in locating a dealer near you.
International Customers should contact their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒ dealer account number
❒ specify preferred method of shipment:
❒ dealer name and address
❒ shipping address (if different than billing address)
❒ Return Fax number
❒ applicable model number
✓ UPS/Fed Ex
■ Priority One
■ Ground
■ Next Day
■ Second/Third Day
✓ DHL
✓ Truck
❒ Quantity, part number and description of each part
NOTICE
All orders are treated as Standard Orders and will ship the same day if received prior to 3PM PST.
We aCCepT aLL maJOR CRediT CaRds!
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 5
Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment.
Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you about potential hazards that could injure you or others. The safety messages specifi cally address the level of exposure to the operator and are preceded by one of four words:
dangeR, WaRning, CauTiOn or nOTiCe.
SAFETY SYMBOLS
dangeR
Indicates a hazardous situation which, if not avoided,
WiLL result in DEATH or seRiOus inJuRY.
WaRning
Indicates a hazardous situation which, if not avoided,
COuLd result in DEATH or seRiOus inJuRY.
CauTiOn
Indicates a hazardous situation which, if not avoided,
COuLd result in minOR or mOdeRaTe inJuRY.
NOTICE
Addresses practices not related to personal injury.
SAfETY INfORMATION
Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.
page 6 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
geneRaL saFeTY
CauTiOn
neveR operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations.
neveR operate this equipment when not feeling well due to fatigue, illness or when under medication.
neveR operate this equipment under the infl uence of drugs or alcohol.
ALWAYS check the equipment for loosened threads or bolts before starting.
dO nOT use the equipment for any purpose other than its intended purposes or applications.
ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.
SAfETY INfORMATION
NOTICE
This equipment should only be operated by trained and qualifi ed personnel 18 years of age and older.
Whenever necessary, replace nameplate, operation and safety decals when they become diffi cult read.
Manufacturer does not assume responsibility for any accident due to equipment modifi cations. Unauthorized equipment modifi cation will void all warranties.
neveR use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.
ALWAYS know the location of the nearest fi re extinguisher.
ALWAYS know the location of the nearest fi rst aid kit.
ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fi re department.
This information will be invaluable in the case of an emergency.
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 7
COMPACTOR SAFETY
dangeR
neveR operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death.
WaRning
neveR disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.
CauTiOn
neveR lubricate components or attempt service on a running machine.
NOTICE
ALWAYS keep the machine in proper running condition.
Fix damage to machine and replace any broken parts immediately.
ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.
engine saFeTY
dangeR
The engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.
The engine of this equipment requires an adequate free fl ow of cooling air. neveR operate this equipment in any enclosed or narrow area where free fl ow of the air is restricted. If the air fl ow is restricted it will cause injury to people and property and serious damage to the equipment or engine.
MVH-306
SAfETY INfORMATION
WaRning
dO nOT place hands or fingers inside engine compartment when engine is running.
neveR operate the engine with heat shields or guards removed.
Keep fi ngers, hands hair and clothing away from all moving parts to prevent injury.
dO nOT remove the radiator cap while the engine is hot. High pressure boiling water will gush out of the radiator and severely scald any persons in the general area of the compactor.
dO nOT remove the coolant drain plug while the engine is hot. Hot coolant will gush out of the coolant tank and severely scald any persons in the general area of the compactor.
dO nOT remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the compactor.
CauTiOn
neveR touch the hot exhaust manifold, muffl er or cylinder. Allow these parts to cool before servicing equipment.
NOTICE
neveR run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter frequently to prevent engine malfunction.
neveR tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.
neveR tip the engine to extreme angles during lifting as it may cause oil to gravitate into the cylinder head, making the engine start diffi cult.
page 8 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
FueL saFeTY
dangeR
dO nOT add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fi re due to static electricity.
MVH-306
MVH-306
dO nOT start the engine near spilled fuel or combustible fl uids. Diesel fuel is extremely fl ammable and its vapors can cause an explosion if ignited.
ALWAYS refuel in a well-ventilated area, away from sparks and open fl ames.
ALWAYS use extreme caution when working with
fl ammable liquids.
dO nOT fi ll the fuel tank while the engine is running or hot.
dO nOT overfi ll tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.
Store fuel in appropriate containers, in well-ventilated areas and away from sparks and fl ames.
neveR use fuel as a cleaning agent.
dO nOT smoke around or near the equipment. Fire or explosion could result from fuel vapors or if fuel is spilled on a hot engine.
SAfETY INfORMATION
BaTTeRY saFeTY (eLeCTRiC sTaRT OnLY)
dangeR
dO nOT drop the battery. There is a possibility that the battery will explode.
dO nOT expose the battery to open fl ames, sparks, cigarettes, etc. The battery contains combustible gases and liquids. If these gases and liquids come into contact with a fl ame or spark, an explosion could occur.
WaRning
ALWAYS wear safety glasses when handling the battery to avoid eye irritation.
The battery contains acids that can cause injury to the eyes and skin.
Use well-insulated gloves when picking up the battery.
ALWAYS keep the battery charged. If the battery is not charged, combustible gas will build up.
dO nOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
ALWAYS recharge the battery in a well-ventilated environment to avoid the risk of a dangerous concentration of combustible gases.
If the battery liquid (dilute sulfuric acid) comes into contact with clothing or skin, rinse skin or clothing immediately with plenty of water.
If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty of water and contact the nearest doctor or hospital to seek medical attention.
CauTiOn
ALWAYS disconnect the negaTive battery terminal before performing service on the equipment.
ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 9
TRanspORTing saFeTY
CauTiOn
NEVER allow any person or animal to stand underneath the equipment while lifting.
NOTICE
Before lifting, make sure that the equipment parts (hook and vibration insulator) are not damaged and screws are not loose or missing.
Always make sure crane or lifi tng device has been properly secured to the lifting bail (hook) of the equipment.
ALWAYS shutdown engine before transporting.
neveR lift the equipment while the engine is running.
Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.
Use adequate lifting cable (wire or rope) of suffi cient strength.
Use one point suspension hook and lift straight upwards.
dO nOT lift machine to unnecessary heights.
ALWAYS tie down equipment during transport by securing the equipment with rope.
enviROnmenTaL saFeTY/deCOmmissiOning
NOTICE
Decommissioning is a controlled process used to safely retire a piece of equipment that is no longer serviceable.
If the equipment poses an unacceptable and unrepairable safety risk due to wear or damage or is no longer cost effective to maintain (beyond life-cycle reliability) and is to be decommissioned (demolition and dismantlement),be sure to follow rules below:
dO nOT pour waste or oil directly onto the ground, down a drain or into any water source.
Contact your country's Department of
Public Works or recycling agency in your area and arrange for proper disposal of any electrical components, waste or oil associated with this equipment.
SAfETY INfORMATION
When the life cycle of this equipment is over, remove battery and bring to appropriate facility for lead reclamation. Use safety precautions when handling batteries that contain sulfuric acid.
When the life cycle of this equipment is over, it is recommended that the trowel frame and all other metal parts be sent to a recycling center.
Metal recycling involves the collection of metal from discarded products and its transformation into raw materials to use in manufacturing a new product.
Recyclers and manufacturers alike promote the process of recycling metal. Using a metal recycling center promotes energy cost savings.
emissiOns inFORmaTiOn
NOTICE
The diesel engine used in this equipment has been designed to reduce harmful levels of carbon monoxide
(CO), hydrocarbons (HC) and nitrogen oxides (NOx) contained in diesel exhaust emissions.
This engine has been certifi ed to meet US EPA Evaporative emissions requirements in the installed confi guration.
Attempting to modify or make adjustments to the engine emission system by unauthorized personnel without proper training could damage the equipment or create an unsafe condition.
Additionally, modifying the fuel system may adversely affect evaporative emissions, resulting in fi nes or other penalties.
emission Control Label
The emission control label is an integral part of the emission system and is strictly controlled by regulations.
The label must remain with the engine for its entire life.
If a replacement emission label is needed, please contact your authorized Kohler Engine Distributor.
page 10 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
SpECIfICATIONS
Table 1. mvh306ds2/dsCpas Reversible plate Compactor specifications
Centrifugal Force vibration Frequency
Traveling speed plate size (L x W) external plate size (L x W) max. area of Compaction (no extensions)
Overall Length
Overall Width
Overall height (with handle)
Overall height (without handle)
Operating Weight
Operating Weight (extension plates)
Lubricating Oil in vibration Case
10,116 lbs. (4,588 kg)
3,600 vpm (60 Hz)
0 to 75 ft/min (0 to 23 m/min)
18 x 34 in (45.72 x 86.36 cm)
24 x 34 in (60.96 x 86.36 cm)
6,750 sq. ft. (2,057 sq. meters)
62 in (1,575 mm)
18.0 in (457 mm )
55 in (1,397 mm )
34 in (864 mm )
725 lbs. (329 kg.)
824 lbs. (374 kg.)
20.28 fl. oz. (600 cc) engine make engine model
Engine Type
Cylinder Bore X stroke displacement maximum Ouput
Oil Capacity
Table 2. engine specifications
YANMAR
L70V6GJ1R1AAS5
Air-cooled 4-cycle Diesel Engine
Fuel Tank Capacity starting method d/ds dry net Weight Recoil/electric dimensions (L x W x h)
3.07 x 2.51 in (78 x 64 mm)
10.34 fl oz (306 cm3)
6.5 HP @3,600 RPM
3.5 quarts (3.31 liters)
1.16 quarts (1.10 liters)
Recoil/Electric
72.75 lbs. (33 kg)/83.77 lbs. (38 kg)
15.11 x 16.57 x 17.71 in (384 x 421 x 450 mm) mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 11
DIMENSIONS
A
MVH-306
E
C
B
D
Figure 1. MVH306DS2/DSCPAS Reversible Plate
Compactor Dimensions
C
D
E
A
B
Table 3. dimensions
55 in. (1,387 mm.)
18 in. (445 mm.)
34 in. (860 mm.)
62 in. (1570 mm.)
34 in. (856 mm.) page 12 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
plate Compactor
The Mikasa MVH306DS2/DSCPAS is a walk behind, reversible plate compactor designed for the compaction of sand, clay and asphalt. This plate compactor is a powerful compacting tool capable of applying a tremendous force in consecutive high frequency vibrations to a soil surface. Its applications include soil compacting for road, embankments and reservoirs as well as backfilling for gas pipelines, water pipelines and cable installation work.
vibratory plates
The vibratory plates of this plate compactor produce low amplitude high frequency vibrations, designed to compact granular soils.
The resulting vibrations cause forward motion. The engine and handle are vibration isolated from the vibrating plate.
The heavier the plate, the more compaction force it generates.
Reversible vibratory plates
Reversible vibratory plates have two eccentric weights that allow a smooth transition for forward and reverse travel, plus increased compaction force as the result of dual weights.
Due to their weight and force, reversible plates are ideal for semi-cohesive soils.
GENERAl NfORMATION
Frequency/speed
The compactor's vibrating plate maximum frequency is
4400 vpm (vibrations per minute). The forward and reverse travel speed of the compactor is approximately 75 ft./minute
(23 meters/minute).
Engine
This plate compactor is equipped with a YANMAR
L70V6GJ1R1AAS5 diesel engine.
Controls
Before starting this plate compactor, identify and understand the function of the controls and all components.
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 13
COMpONENTS
16
2 10
1
4
12
14
15
3
MVH-306
6
5
9
7
13
12
11
8
Figure 2. MVH306DS2/DSCPAS Reversible Plate Compactor Components
Figure 2 illustrates the location of the major components for the MVH306DS2/DS2CPAS Reversible Plate Compactor.
The function of each component is described below:
1.
2. Forward & Reverse Lever – Push the lever forward,
3. handle Bar – When operating the compactor, this
4.
5.
6. Engine – This plate compactor uses a YANMAR
7.
hand grip – When operating the compactor use this hand grip to maneuver the compactor.
the compactor will move in a forward direction, pull the lever backwards, the compactor will move in backwards direction. Placing the lever in the middle (midway) will cause the compactor not to move (neutral). handle is to be in the downward position. When the compactor is to be stored, move the handle bar to the upright position.
guard hook - Used to lift the machine with crane or other lifting device.
Stopper - Locks the handle in place in the upward position for stowing.
L-70V6 diesel engine. Refer to the owner’s manual for engine information and related topics.
Battery (Option) - This unit uses a 12-volt battery. See maintenance of this manual for proper care of battery.
8. Belt Cover – Remove this cover to gain access to the
V-belts. neveR run the compactor without the V-belt cover. If the V-belt cover is not installed, the possibility exist that your hand may get caught between the V-belt and clutch, thus causing serious injury and bodily harm.
9. Base plate – Designed to compact sand, clay, and asphalt.
10. Oil Reservoir – Fill with Shell Tellus Oil 46 or equivalent grade hydraulic oil.
11. vibration Case – Encloses the eccentric, gears and counter weights.
12. hydraulic Cylinder – Activated by moving the travel lever. The cylinder controls the direction of movement by the plate compactor.
13. shock absorber – Protects plate compactor from damage by absorbing vibration during operation.
14. Throttle Lever – Controls speed of the plate compactor. Place straight vertically to start, push fully counterclockwise for full throttle and fully clockwise to stop plate compactor.
15. ignition switch (Option) – Provided for electric start models only.
16. COMPAS – Compaction Analysing System, monitors soil stiffness. Available only on the MVH306DSCPAS.
page 14 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
bASIC ENGINE
9
3
4
1
2
10
5
7
6
8
Figure 3. Yanmar L70V6 Engine Components
engine COmpOnenTs
Figure 3 illustrates the location of the major components for the Yanmar L70V6 diesel engine. The function of each component is described below
1. Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tighten securely. dO nOT over fill.
2. Fuel Tank – Capacity is 3.5 quarts (3.31 liters) of diesel fuel.
3. Air Cleaner – Prevents dirt and other debris from entering the fuel system. Remove wing-nut on top of air filter cannister to gain access to filter element.
4. muffler – Used to reduce noise and emissions.
5. Recoil starting handle (pull rope) – Type of engine starting method. Alternate type would be electric start
(ignition key).
6. Recoil Starter – Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and smoothly.
7. Oil Filler Cap / dipstick – Remove this cap to add oil to the engine crankcase. Read dipstick to determine if oil level is low. dO nOT over fill.
8. Oil Drain Plug – Unscrew plug to drain oil from engine crankcase. Dispose of oil in a safe manner.
9. decompression Lever – Press down before starting engine. To prevent damage to engine, dO nOT use for any other purpose.
10. Fuel Cock – Controls the flow of diesel fuel to the carburetor. Must be in the ON position when starting and running the engine.
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 15
Before starting
1. Read safety instructions at the beginning of manual.
2. Familiarize yourself with the operating and control elements of the machine and the working environment.
This includes obstacles in the working area, bearing capacity of the ground and the necessary safety provisions.
3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.
4. Check fastening nuts and bolts for tightness. Loose threads may cause damage to the machine when vibrating.
5. Understand the geographical features and regulations of the job site.
6. Clean the compactor, removing dirt and dust.
Particularly, the bottom of the plate, engine cooling air inlet.
Checking engine Oil Level
1. To check the engine oil level, place the compactor on secure level ground with the engine stopped.
2. Remove the dipstick from the engine oil filler hole
(Figure 4) and wipe it clean.
3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.
INSpECTION
UPPER
LEVEL
LOWER
LEVEL
Figure 5. Engine Oil Level season
Table 4. Oil Tyoe
Temperature Oil Type
Summer
Spring/Fall
Winter
25°C or Higher SAE 10W-30
25°C~10°C
SAE 10W-
30/20
0°C or Lower SAE 10W-10
Checking the hydraulic Oil Level
1. To check the engine oil level, place the compactor on secure level ground with the engine stopped.
2. Remove the hydraulic oil breather cap located at the top of the hydraulic oil tank (Figure 6).
3. Using a 24 mm wrench, remove the hydraulic oil filler plug.
4. Visually inspect to determine if hydraulic oil level is low. If oil level is low add Shell Tellus 46 hydraulic oil or equivalent through the hand pump oil filler port.
BREATHER
CAP
OIL
TANK
Figure 4. Engine Oil Dipstick Removal
4. If the oil level is low (Figure 5), fill to the edge of the oil filler hole with the recommended oil type (Table 4).
Maximum oil capacity is 1.16 quarts (1.10 liters).
HYDRAULIC
OIL PLUG
(24 MM WRENCH)
Figure 6. Hydraulic Oil Filler Plug Removal page 16 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
CauTiOn
dO nOT overfill hydraulic oil tank. This could cause oil leaks and sluggish operation. Clean cap and surrounding area before opening to prevent dirt from entering oil tank.
5. When adding hydraulic oil, only fill to the specified oil level as marked on the front of the hydraulic oil tank
(Figure 7).
dO nOT overfill.
OIL
TANK
INSpECTION
3. Remove the air cleaner element (Figure 9) and inspect it for signs of wear or dirt. If air cleaner element is dirty, clean or replace element.
ELEMENT
OIL LEVEL
Figure 7. Oil Tank (Front View)
Checking the air Cleaner
1. To check the engine oil level, place the compactor on secure level ground with the engine stopped.
2. Loosen the wing nut (Figure 8), remove the air cleaner cover.
AIR
CLEANER
Figure 9. Air Cleaner Element
dangeR eXpLOsive FueL!
Motor fuels are highly flammable and can be dangerous if mishandled. dO nOT smoke while refueling. dO nOT attempt to refuel if the engine is hot or running.
Checking The Fuel
1. Remove the fuel cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low, replenish with diesel fuel (Figure 10 ).
3. When refueling, be sure to use a strainer for filtration.
dO nOT top-off fuel. Wipe up any spilled fuel.
WING
NUT
Figure 8. Checking the Air Cleaner Figure 10. Refueling mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 17
CauTiOn
dO nOT attempt to operate the compactor until the Safety, General Information and
Inspection sections of this manual have been read and thoroughly understood.
OpERATION
3. When the handle is raised to the desired height, tighten the butterfly screw.
This section is intended to assist the operator with the initial start-up of the compactor. It is extremely important that this section be read carefully before attempting to use the compactor in the field.
Refer to Figure 3 for the location of controls and components.
Releasing the Handle
1. Pull the handle release pin, (Figure 11) then push down on the hand grip to release the handle.
Figure 12. Handle Adjustment
sTaRTing The engine
Electric Start (Option)
1. Place the fuel cock (Figure 13) in the open position.
MVH-306
HANDLE
RELEASE
PIN
PULL UP
TO RELEASE
HANDLE
Figure 13. Fuel Cock Open Position)
2. Place the throttle lever (Figure 14) in the START position (center). Place the travel lever in the neutral position (center)
TRAVEL
LEVER
NEUTRAL
REVERSE
FORWARD
Figure 11. Handle Release Pin
adjusting handle height
The height of the handle is adjustable for your comfort .
1. Loosen the butterfly screw (Figure 12).
2. Turn the grip clockwise to raise the handle or counterclockwise to lower the handle.
THROTTLE
LEVER
START
(CENTER POSITION)
Figure 14. Travel/Throttle Lever
(Start Position) page 18 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
NOTICE
When starting a unit with an electric strart capability, a decompressor is not normally required. However, when ambient temperature or battery charger level is low, use of a decompressor will help make the start-up easier.
3. Insert the ignition key into the ignition switch and turn it to the Run position (Figure 15). The buzzer should sound at this time.
4. Turn the ignition key further to the right to the START position to start the engine. Buzzer stops sounding and the engine starts.
5. If the engine fails to start, dO nOT continue to rotate the ignition key for more than 5 seconds. Return the key to the Run position and wait 10 seconds before starting again
OpERATION
Recoil Start
1. Place the fuel cock in the Open position (Figure 13).
2. Move the throttle lever to the START position
(Figure 14).
3. Grasp the starter grip (Figure 16) and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting.
STOP
RUN
START
Figure 15. Starter Switch (Option)
;
CauTiOn
While the engine is running, never try to turn the ignition key to the START position.
6. After starting the engine, continue to warm up the engine for about 3 to 10 seconds especially in cold weather.
7. If the buzzer does not stop sounding after the engine has started, shutdown engine immediately and check engine oil level. The buzzer functions as a engine oil level alarm warning device.
Figure 16. Engine Start Handle
4. Push down decompression lever (Figure 17) and release.
Figure 17. Decompression Lever
5. If the engine does not start, repeat steps 1 thru 4 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 19
TRaveLing
CauTiOn
Make sure to follow all safety rules referenced in the safety section of this manual before operating compactor. Keep work area clear of debris and other objects that could cause damage to the compactor or bodily harm.
1. Grasp the compactor's hand grip, and move the engine throttle lever (Figure 18) quickly to the fast position.
2. With the throttle lever in the fast position, the engine speed should be around 3,600 RPM, therefore engaging the centrifugal clutch.
HAND
GRIP
FULL THROTTLE
POSITION
Figure 18. Throttle Lever (Fast)
NOTICE
ALWAYS move the throttle lever quickly without hesitation, because increasing the engine speed slowly causes the clutch to slip.
3. To make the compactor move in the forward direction push the travel lever ( Figure 19) forward.
TRAVEL
LEVER
NEUTRAL
REVERSE
OpERATION
4. To make the compactor move in the reverse direction pull the travel lever ( Figure 19) backwards.
5. Firmly gasp the compactor's hand grip, the compactor will begin moving in the desired position when the direction lever has been placed in the desired position.
6. Slowly walk behind the compactor and be on the lookout for any large objects or foreign matter that might cause damage to the compactor or bodily injury.
7. If travel lever is placed in the neutral position, the machine will vibrate in place.
8. To move the compactor laterally, hold the hand grip firmly and swing compactor. dO nOT swing compactor while gripping the travel lever.
normal shutdown
1. Return the throttle lever to the START position
(Figure 14). Allow the machine to cool down for 2 to
3 minutes.
2. Place the travel lever in the neuTRaL position (Figure 20).
3. Place the throttle lever in the STOP position (Figure 20) to stop the engine.
TRAVEL
LEVER
NEUTRAL
POSITION
STOP
POSITION
THROTTLE
LEVER
Figure 20. Throttle Lever (Stop)
FORWARD
Figure 19. Travel Lever page 20 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
4. If using an electric start unit, return the key switch to the
STOP position (Figure 21) as soon as the engine stops.
Figure 21. Starter Switch (STOP)
5. Place the fuel cock (Figure 22) in the closed position.
OpERATION emergency shutdown
1. For a recoil start type engine, move the throttle lever quickly to the STOP position.
2. For an electric start type engine, place the engine ignition switch in the OFF position.
sTOWing The handLe
1. Push up the handle upward (Figure 23) until the handle locks in place.
MVH-306
Figure 22. Fuel Cock (Closed Position)
Figure 23. Stowing The Handle mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 21
COmpaCTiOn sensOR (mvh306 dsCpas Only)
Compaction Analyzing System (COMPAS) is a system that uses an acceleration sensor to show real-time soil stiffness via LED's (light-emitting diode) turning on with each pass of the compactor.
This COMPAS improves compaction work efficiency because it can prevent an already properly compacted area from being compacted more than necessary and identify an area where more compaction is needed.
COMPAS also has a function to detect abnormalities such as vibration trouble (insufficient vibration frequency), ground trouble (soft soil) and other functional issues (Figure 24).
NORMAL OPERATION
(GREEN LED ON)
COMPACTION LIMIT
LED’S 1 THRU 8 ON
PLUS RED LED ON
VIBRATION ABNORMALITY
(GREEN LED FLASHING)
SOIL PROBLEM,
GREEN, AND RED
LED’S ON
OpERATION
When the plate compactor is in idle mode the green LED will begin flashing and the red LED will turn on. As the engine RPM's are increased and compaction begins, the
green LED will stop flashing and turn on (solid). The red
LED will turn off and the #1 yellow LED will turn on. As compaction progresses the number of yellow LEDs, 2 thru
8 will turn on (Figure 25).
The number of yellow status LEDs that will turn on is soil dependent.
NORMAL OPERATION
(GREEN LED ON)
COMPACTION PROGRESSION LED’S 1 THRU 8 ON
Figure 24. Compaction Sensor (COMPAS)
NOTICE
COMPAS can only show progression of the soil stiffness and is not meant to measure absolute soil density.
When using COMPAS always calculate appropriate soil density by conducting proper testing such as plate load test and dynamic load test to best compliment the LED lighting progression with the actual measurement value.
normal Compaction (
Compaction progression
)
NOTICE
Not all yellow status LEDs will turn on. The progression of the yellow status LEDs depends on the type of soil being compacted. If compacting gravel (stiff soil)
potentially all status LEDs will turn ON.
If compacting sand (soft soil), fewer status LED's will turn ON. Remember dO nOT over compact.
INITIAL COMPACTION YELLOW LED#1 ON
COMPACTION PROGRESSION LED’S 2 THRU 8 ON
Figure 25. Compaction Progression
normal Compaction (Compaction Limit)
The compaction limit (Figure 26) is achieved when all the yellow LED's 1 thru 8 including the red LED are all on, depending on type of soil being compacted . At this point the machine cannot compact any further. If the compaction results are not satisfactory then check and make sure the soil type, moisture content, lift and number of passes are proper for this machine.
DURING COMPACTION YELLOW
LED’S 1 THRU 8 ON
RED LED ON
Figure 26. Compaction Limit page 22 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
system diagnostics to detect Operational abnormalities
Detection of ground trouble and soft ground
1. For a case of unstable ground or soft ground (soil containing high clay content) for which the use of this machine is not suitable, only the green and red LEDs will be on (Figure 27), with no yellow LED's on.
If this occurs it would be challenging to achieve the desired compaction results. Check to make sure the ground conditions are prepared to specification before proceeding with the compaction process.
GREEN
LED ON
GROUND TROUBLE
OR
SOFT GROUND
RED
LED ON
GREEN LED
FLASHING
OpERATION
VIBRATION ABNORMALITY DUE TO
IMPROPER ENGINE RPM
Figure 28. Vibration Abnormality
Improper Engine RPM's
Function to detect electric system abnormality
Sensor wire disconnection (between acceleration sensor and sensor panel)
3. If red and green LEDs are flashing alternately as shown in Figure 29 then please check the sensor wire because there is a possibility that it is disconnected.
RED LED
FLASHING
Figure 27. Ground Trouble or Soft Ground
Detection of Vibration Abnormality
2. When appropriate vibration frequency cannot be achieved during operation due to improper engine
RPMs (Figure 28) the green LED will flash. When this occurs check the engine RPMs and the V-belt tension as it could be loose.
GREEN LED
FLASHING
Figure 29. Sensor Wire Disconnection
Power cable disconnection (between battery and sensor panel)
4. If there are no LEDs on or flashing even when the key switch is turned on then please check the power cable because there is a possibility it is disconnnected.
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 23
CauTiOn
Inspection and other services should always be carried out on hard and level ground with the engine shutdown.
inspection and maintenance service Tables.
To make sure your plate compactor is always in good working condition before using, carry out the maintenance inspection in accordance with Table 5 thru Table 7.
Table 5. mvh-306ds2/dsCpas machine inspection item hours of Operation
Loose or Missing Screws Every 8 hours (every day)
Damaged Parts
Function of Controlling
System Part
Hydraulic System Leak
Vibrator Oil Check Every
Vibrator Oil Replacement
Every 8 hours (every day)
Every 8 hours (every day)
Every 100 hours
Every 100 hours
Every 300 hours
Hydraulic Oil Check Every Every 100 hours
Hydraulic Oil Replacement
First after 200 hours, then every
1,000 hours
V-belt (clutch) Check Every 200 hours
Battery Check Every 100 hours
CauTiOn
These inspection intervals are for operation under normal conditions. Adjust your inspection intervals based on the number hours plate compactor is in use, and particular working conditions.
NOTICE
Fuel piping and connections should be replaced every
2 years.
MAINTENANCE
Table 6. mvh-306ds2/dsCpas engine Check item hours of Operation
Oil or Fuel Leak
Tightness of Fastening
Threads
Engine Oil Check and Replenishment
Engine Oil Replacement
Air Filter Cleaning Every
Every 8 hours (every day)
Every 8 hours (every day)
Every 8 hours (every day) (Replenish to specified maximum level)
After first 25 hours then every 50 to 100 hours
100 hours
See separate engine manual for details on engine check.
daily service
Check for leakage of fuel or oil.
Check for loose screws including tightness. See Table 7 below (tightening torque ), for retightening:
Table 7. Tightening Torque
(in. kg/cm) diameter
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T 70 150 300 500 750 1,100 1,400 2,000
6-8T 100 250 500 800 1,300 2,000 2,700 3,800
11T 150 400 800 1,200 2,000 2,900 4,200 5,600
* 100
300~
350
650~
700
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt, and screw.
Remove soil and clean the bottom of compaction plate.
Check hand pump, piping and hose for any leakage. A loosened hydraulic hose can be a cause for leakage.
Check hydraulic hose connections with wrench applied for tightness.
Check engine oil.
page 24 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
MAINTENANCE engine Oil Replacement:
1. Replace engine oil, in first 25 hours of operation and every 50 to 100 hours afterwards.
2. Oil may be drained more easily when it is warm afteroperation (For more details, see separate engine
Owner's Manual).
air Filter (every 6 months or 400 hours)
1. The air filter element (Figure 30) should be cleaned because a clogged air cleaner can cause poor engine starting, lack of power and shorten engine life substantially.
Figure 30. Engine Air Filter and Element
2. To clean or replace air filter loosen the wing nut on the air filter housing (Figure 30) remove the cover and take out air filter cartridge. If only cleaning of the air filter is desired blow through the air filter cartridge from the inside, moving a jet of dry compressed air up and down until all dust is removed.
CauTiOn
neveR attempt to check the V-belt with the engine running. Severe injury can occur if your hand gets caught between the V-belt and the clutch (Figure 31).
Always use safety gloves.
CLUTCH
PULLEY
CLUTCH
V-BELT
VIBRATOR PULLEY
BELT COVER
Figure 32. V-Belt Check
Replacing the v-belt
Remove the belt cover (Figure 32). Engage an offset wrench 3/4”(19 mm) or the like to vibrator pulley (lower) fastening bolt. Engage wastecloth or the like at midway of V-belt on the left side and whilepulling it back strongly, rotate the offset wrench clockwise so that the V-belt will come off.
Reinstalling the v-belt
Engage V-belt to lower vibrator pulley and push the V-belt to leftside of upper clutch and, in the same manner as in removal, rotate offset wrench clockwise so that the
V-belt goes back on.
Checking Clutch
Check the clutch simultaneously with V-belt checking.
With belt cover removed, check outer drum of the clutch for seizure and "V" groove for wear or damage with your eyes. Clean the "V" groove as necessary. If the shoe is worn, power transmission becomes deficient and slipping will result.
Replacing Clutch
Remove V-belt. Remove bolt at engine power output by giving a light tap with a hammer to an engaged wrench and rotate bolt counterclockwise. Remove clutch with a pulley extractor. To reinstall, reverse the procedure.
CauTiOn
When ever the compactor's vibration becomes weak or lost during normal operation regardless of operation hours, check the V-belt and clutch immediately.
VIBRATOR
PULLEY
Figure 31. V-Belt Hazard mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 25
vibrator Oil Level Check
NOTICE
ALWAYS clean the area around the vibrator oil level check plug before removing oil check plug. This will prevent dirt and debris from entering the system.
1. In every 100 hours of operation, with the machine positioned horizontally, use a 3/4” (19 mm) wrench and remove vibratoroil level check plug (Figure 33). Visually inspect and see if vibrator oil level is up to filler port.
Be sure to clean area around check hole to prevent dirt and dust from entering.
ADD 10W-30 WT.
MOTOR OIL
HERE
OILGAUGE/
DIPSTICK
MAINTENANCE
4. After hydraulic oil has been completely drained from machine, fill with 10W-30 motor oil to the appropriate safe operating level (Figure 33).
5. Reinstall drain plug into vibrating plate assembly. Apply seal tape or Loctite #575 to thread portion of drain plug.
draining hydraulic Oil
1. Disconnect the hydraulic hose (Figure 34) connected to the hydraulic oil cylinder.
2. Push the travel lever back and forth to drain the hydraulic oil from the hand pump (hydraulic oil reservoir).
HYDRAULIC
HOSE
DRAIN
BOLT
OILGAUGE/
DIPSTICK
CORRECT
DRAIN
BOLT EXCITER OIL LEVEL CASING NORMAL
FILL TO 600CC
MAXIMUM
INCORRECT
EXCITER OIL LEVEL CASING OVERFILLED
Figure 33. Vibrator Oil Drain and Check Plugs
draining vibrator Oil
1. Replace vibrator oil after first 200 hours and in every
1,000 hours of operation. Oil capacity is 600 cc.
2. Position handle bar vertically (storage position).
3. Using a 14 mm wrench remove the vibrator oil drain plug (Figure 33) from the vibrating plate assembly.
NOTICE
For draining oil through level check hole, have the machine inclined with a sleeper or the like placed under the compaction plate on opposite side.
HYDRAULIC
CYLINDER
Figure 34. Hydraulic Oil Cylinder/Hose
3. After draining hydraulic oil, reconnect hydraulic oil hose to cylinder.
4. Place handle in upright position. Pull travel lever all the way back (reverse), and using a rope, secure travel lever to hand grip.
adding hydraulic Oil
1. Remove the breather cap and oil plug (Figure 35) from thehydraulic oil tank using a 24mm hex socket.
BREATHER
CAP
OIL
TANK
HYDRAULIC
OIL PLUG
(24 MM WRENCH)
Figure 35. Hydraulic Oil Tank page 26 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
2. Using a funnel, add Shell Tellus Oil #32 or equivalent to the hydraulic oil tank through the oil filler port
(Figure 36). Oil tank capacity is 18.7 fl. oz (550 cc).
S
T
E
0I
H
E
L
L
L
L
L
U
#4
S
6
HYDRAULIC
OIL TANK
OIL LEVEL
FILL TO
THIS LEVEL
FRONT VIEW REAR VIEW
Figure 36. Adding Hydraulic Oil
CauTiOn
Make sure hydraulic oil is at a normal safe operating level. dO nOT over fill. Over filling (excessive oil) will cause excess oil to blow out of breather plug.
3. Loosen bleeder plug located at top of hydraulic cylinder on side of vibrator (Figure 37). Air remaining in the circuit will be forced out of the bleeder plug. Once all air has been purged from the hydraulic system, tighten bleeder plug securely
4. Reinsert oil plug into hydraulic oil tank and tighten securely. Reinstall breather cap.
NOTICE
The bleeder plug should only be loosened, but not removed.
BLEEDER
PLUG
MAINTENANCE
CauTiOn
ALWAYS wear safety glasses or face mask, protective clothes, and rubber gloves when working with battery.
BaTTeRY mainTenanCe (Option)
Mishandling of the battery shortens the service life of the battery and adds to maintenance cost. When handling the battery do the following:
The battery electrolyte contains sulfuric acid, be careful not to let the battery electrolyte come in contact with your body or clothing.
Always check the battery terminals periodically to ensure that they are in good condition.
Always wear eye protection and rubber gloves, since the battery contains sulfuric acid which burns skin and eats through clothing. In case of contact, flush thoroughly with water and contact a doctor immediately.
Use wire brush or sand paper to clean the battery terminals.
Always check battery for cracks or any other damage.
If white pattern appears inside the battery or paste has accumulated at the bottom, replace the battery.
If the compactor will not be in operation for a long period of time, store in cool dry place and check the battery charge level every month to maintain the performance of the battery.
Check the battery regularly and make sure that each electrolyte level is to the bottom of the vent well (Figure 38).
If necessary add only distilled water in a well-ventilated area.
HYDRAULIC
CYLINDER
Figure 37. Bleeder Plug
Figure 38. Battery Electrolyte Levels mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 27
BaTTeRY ChaRging
dO nOT charge battery with the battery cables connected to the compactor. The diodes will be damage by the high voltage.
Batteries generate hydrogen gas which can be highly explosive. dO nOT smoke or allow flames or sparks near the battery, especially during charging of the battery.
Charge the battery in a open air environment (plenty of ventilation).
Before charging , remove the cap from each cell of the battery.
Connect the positive (+) lead of the charger to the positive (+) terminal of the battery and the negative (-) lead of the charger to the negative (-) terminal of the battery. dO nOT reverse the polarity when charging.
Reverse polarity will damage the charger rectifier or the battery.
Battery fluid will be lost through continuous charging and discharging.
Discontinue charging if the electrolyte temperature exceeds 117° F (45° C).
NOTICE
During summer much more battery fluid is lost than in winter. Before starting, check battery electrolyte levels and replenish with distilled water to the upper mark on the battery.
MAINTENANCE
BaTTeRY CaBLe COnneCTiOn (Option)
1. Take off the battery cover by removing the M6 nuts that secure the battery holder to the cover.
2. When removing battery cables, disconnect the ground side (normally negative) first (Figure 39).
3. When installing battery cable connect the ground side
(normally negative) last.
Figure 39. Removing Battery Cover
CheCKing FueL FiLTeR
1. Clean the fuel filter every 3 months or 200 hours.
2. Replace fuel filter every 6 months or 400 hours.
3. To clean the fuel filter, loosen the nuts (Figure 40) of the fuel cock and pull out the filter from the F.O. tank filler port. Wash the filter thoroughly with diesel fuel oil.
4. Reinstall fuel filter and connect all associated hardware
DRAIN
PLUG
NUTS page 28 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
Figure 40. Fuel Filter
LOng TeRm sTORage
When storing your compactor for long periods do the following:
1. Run the engine at idle speed for 3-5 minutes.
2. Stop the engine. Drain the engine crankcase oil while the engine is still warm. Fill Engine crankcase with fresh oil.
3. Remove the rubber plug (Figure 41) on the rocker arm cover and add about 2 cc of lube oil. Reinstall rubber plug.
RUBBER
PLUG
MAINTENANCE
Figure 42. Recoil Starter Grip
5. For electric start type compactors, turn the engine for
2 or 3 seconds with the decompression lever set in the non-decompression position, and the starter key at the
START position. dO nOT start the engine.
6. Pull the decompression lever up. Pull the recoil starter grip slowly. STOP when it feels tight. This closes the intake and exhaust valves (compression position) , and helps prevents ruts from forming.
7. Wipe any oil or dirt that may have accumulated on the compactor.
8. Store compactor in a cool dry place out of the reach of children or unauthorized personnel
DECOMPRESSION
LEVER
Figure 41. Decompression Lever
4. For recoil type compactors, push the decompression down (non-decompression position) and hold it while you pull the recoil starter grip (Figure 42) rope 2 or 3 times. dO nOT start the engine.
STARTER
GRIP mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 29
ExplANATION Of CODE IN REMARkS COluMN
The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions.
NOTICE
The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed.
sampLe paRTs LisT
nO. paRT nO. paRT name QTY. REMARKS
1 12345 BOLT .....................1 .....INCLUDES ITEMS W/%
2% WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY
2% 12347 WASHER, 3/8 IN. ..1 .....MQ-45T ONLY
3 12348 HOSE ..................A/R ...MAKE LOCALLY
4 12349 BEARING ..............1 .....S/N 2345B AND ABOVE
nO. Column
unique symbols — All items with same unique symbol
(@, #, +, %, or >) in the number column belong to the same assembly or kit, which is indicated by a note in the
“Remarks” column.
duplicate item numbers — Duplicate numbers indicate multiple part numbers, which are in effect for the same general item, such as different size saw blade guards in use or a part that has been updated on newer versions of the same machine.
NOTICE
When ordering a part that has more than one item number listed, check the remarks column for help in determining the proper part to order.
paRT nO. Column
numbers used — Part numbers can be indicated by a number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part that has not been assigned a formal part number at the time of publication.
A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarifi ed in the “Remarks” Column.
QTY. Column
numbers used — Item quantity can be indicated by a number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold separately. Other entries will be clarifi ed in the “Remarks”
Column.
REMARKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to describe the item can also be shown.
assembly/Kit — All items on the parts list with the same unique symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
serial number Break — Used to list an effective serial number range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
specifi c model number use — Indicates that the part is used only with the specifi c model number or model number variant listed. It can also be used to show a part is NOT used on a specifi c model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“make/Obtain Locally” — Indicates that the part can be purchased at any hardware shop or made out of available items. Examples include battery cables, shims, and certain washers and nuts.
“not sold separately” — Indicates that an item cannot be purchased as a separate item and is either part of an assembly/kit that can be purchased, or is not available for sale through Multiquip.
page 30 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
MVH306DS2/DSCPAS W/YANMAR L70V6 DIESEL ENGINE
1 to 3 Units
Qty. p/n description
1............956100054 ............THROTTLE WIRE
2............070200373 ............V-BELT
3............11425012580 ........ELEMENT W/ PRE-FILTER
1............16081076630 ........STARTER ROPE
2............11425055121 ........FUEL FILTER W/GASKET
1............11428855010 ........CAP, FUEL TANK W/GASKET
1............11425035110 ........LUBE OIL STRAINER
1............11425055100 ........FUEL STRAINER
1............955300680 ............IGNITION SWITCH W/ KEY
3............955000010 ............KEY, IGNITION SWITCH
SuGGESTED SpARE pARTS
NOTICE
Part numbers on this Suggested Spare Parts list may supersede/replace the part numbers shown in the following parts lists.
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 31
NAMEplATES AND DECAlS
page 32 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
8
9
6
7
2
3
4
5 nO. paRT nO.
1 920201950
920105070
920110370
920209620
920211090
920204580
920203330
920211060
920213920
920216620 9
10 920201580
11 920211010
12 920106760
14 920214100
15 920216610
NAMEplATES AND DECAlS
paRT name
DECAL: OIL SAE 10W-30
QTY.
1
REMARKS
DECAL: MIKASA LOGO ....................................1................ELECT. START MODEL ONLY
DECAL: MODEL LOGO MVH-306
DECAL: CAUTION
DECAL: SHELL TELLUS OIL 32
DECAL: FULL THROTTLE
DECAL: EAR PROTECTION
1
1
1
1
DECAL: CAUTION (TRAVEL LEVER)
1
1
DECAL: SERIAL NO. ........................................1................CONTACT MQ PARTS DEPT.
DECAL: SERIAL NO. (PAS) ...............................1................CONTACT MQ PARTS DEPT.
DECAL: MQ LOGO
DECAL: V-BELT HDPF-5370
DECAL: STOP-RUN-START
DECAL: E/G FIRE WARNING
DECAL: CAUTION (FOR WASHING)
1
1
1
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 33
VIbRATING plATE ASSY.
page 34 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
2
3
4
5 nO. paRT nO.
1 464117840
464460660
6
7
8
9
953402930
953400270
953405260
939010260
020316130
030216400
001221635
10 001221830
11 58407
12 030216400
15 939010010
16 020310080
17 031110160
18 030210250
19 464343730
20 011008015
21 030208200
31 52993
32 012218050
33 58407
VIbRATING plATE ASSY.
paRT name
VIBRATING PLATE
DRAIN PLUG
COPPER PACKING 19X30X1
PLUG 1/4X14 10L
PACKING 1/4 (CU)
SHOCK ABSORBER 110X60H
NUT M16
WASHER, LOCK M16
SHOCK ABSORBER, STOPPER 45
NUT M10
WASHER, FLAT M10
4
4
1
1
QTY.
1
1
1
WASHER, LOCK M16
BOLT 16X35 T
4
4
BOLT 18X30 T 8
WASHER, LOCK M18 .......................................8................REPLACES P/N 030218460
4
4
4
4
REMARKS
WASHER, LOCK M10
COVER, VIBRATING PLATE
4
2
BOLT 8X15 T .....................................................8................REPLACES P/N 001220815
WASHER, LOCK M8 8
EXTENSION PLATE .........................................2................REPLACES P/N 456210690
BOLT 18X50 T ...................................................8................REPLACES P/N 001221850
WASHER, LOCK M18 .......................................8................REPLACES P/N 030218460 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 35
bASE AND ENGINE ASSY.
page 36 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
2
3
4
5 nO. paRT nO.
1 464117850
914410026
6
7
8
9
012210040
030210250
031110160
464216560
011208025
030208200
0401450080
10 464343670
11 464457360
12 456343340
13 951406790
14 952400690
15 011208030
16 030208200
17 464216640
18 092006010
19 464343660
20 464216590
21 001521050
35 464117920
36 456449950
37 011208030
38 030208200
39 0401450080
40 022710809
bASE AND ENGINE ASSY.
paRT name
BASE
QTY.
1
REMARKS
ENGINE ASSY. L70V6 (YANMAR) 1
BOLT 10X40 T ...................................................4................REPLACES P/N 001221040
WASHER, LOCK M10
WASHER, FLAT M10
4
4
BELT COVER (IN) 1
BOLT 8X25 T .....................................................4................REPLACES P/N 001220825
WASHER, LOCK M8 4
WASHER, FLAT M8 ..........................................4................REPLACES P/N 031108160
DUST-PROOF SPONGE (IN)
SPACER/MVH-306
1
1
CLUTCH ASSY./CHM03/W.FAN 1
KEY 7X7X36 RR ...............................................1................REPLACES P/N 22512070360
WASHER 9X35X4.5 1
BOLT 8X30 T .....................................................1................REPLACES P/N 001220830
WASHER, LOCK M8
DUST-PROOF COVER
FLAT HEAD SCREW 6X10
DUST-PROOF SPONGE (OUT)
BELT COVER (OUT)
SOCKET HEAD BOLT 10X50 T
RUBBER COVER (GUARD FRAME)
PLATE, COVER
1
1
1
4
3
1
1
1
BOLT 8X30 T .....................................................3................REPLACES P/N 001220830
WASHER, LOCK M8 3
WASHER, FLAT M8 ..........................................3................REPLACES P/N 031108160
NYLON NUT M8 3 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 37
bASE AND ENGINE ASSY. (CONTINuED)
page 38 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
bASE AND ENGINE ASSY. (CONTINuED)
nO. paRT nO.
41 2556390111
42 2556380103
43 0091720000
44 0211140020 GASKET (OIL DRAIN) ......................................2................REPLACES P/N 459010080
45 R0401140030 PLUG ................................................................1................REPLACES P/N 459010100
46 464457380
47 014208020
48
49
51
52
53
59
60
61
62
63
64
65
66
70
71
72
030208200
454010020
464118780
012214030
030214350
459455560
459010110
070200373
459000020
2067550101
58151
020406040
959406800
959407260
012210015
030210250 paRT name QTY. REMARKS
UNION TIP, DRAIN ...........................................1................REPLACES P/N 459010060
DRAIN HOSE ....................................................1................REPLACES P/N 459010070
HOSE BAND .....................................................2................REPLACES P/N 459010090
DRAIN JOINT 1
BOLT 8X20 T .....................................................1................REPLACES P/N 001220820
WASHER, LOCK M8
CLAMP TC-100
1
1
GUARD HOOK 1
BOLT 14X30 T ...................................................4................REPLACES P/N 001221430
WASHER, LOCK M14
UNION, OIL DRAIN
SEAL WASHER 16S
V-BELT
1
1
4
1
RETURN SPRING 1
CLAMP CP. .......................................................1................REPLACES P/N 151010680
WASHER, FLAT M5 ..........................................1................REPLACES P/N 031105080
NUT M6, H=4.2
NUT M6 (SPECIAL-L10)
CLIP D6 (FOR M10)
1
1
1
BOLT 10X15 T ...................................................1................REPLACES P/N 001221015
WASHER, LOCK M10 1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 39
VIbRATOR ASSY.
page 40 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
nO. paRT nO.
A 464910020
1# 464117880
2
3
001221470
001221450
4 030214350
5# 047920120
6# 457212410
8# 951405370
9# 456327150
10# 080200550
11# 060105030
12# 951404970
13# 464343700
14# 009120301
15# 456337670
16# 009120302
17# 456337380
18# 456010010
19# 464343720
20# 040306911
21# 953010030
25# 042506000
26# 0080000010
27# 455435051
28# 455010070
29# 080100260
30# 456327130
31# 456210636
33# 050101050
34# 0105091025
35# 030210250
36# 011008015
37# 953404600
38# 455010020
39# 031110160
43# 952405470
46# 464343710
47# 464457370
48# 012012030
49# 030212300
51 464216600
52 001520852
VIbRATOR ASSY.
paRT name QTY. REMARKS
VIBRATING ASSY. .............................................1................INCLUDES ITEMS W/ #
VIBRATING CASE
BOLT 14X150 T
BOLT 14X50 T
WASHER, LOCK M14
ROLLER BEARING NJ310EMC4
ROTARY SHAFT, DRIVE
KEY 15X10X39 RR
GEAR, DRIVE
STOP RING S-55
OIL SEAL SB-50729
KEY 12X8X30 R
ECCENTRIC ROTATOR
SOCKET HEAD BOLT 16X40 T
ROTARY SHAFT, DRIVEN
SOCKET HEAD BOLT 16X30 T
PISTON ROD
KNOCK PIN 10X70
GEAR (DRIVEN)
BEARING 6911
SEAL CAP/SC72-8N
BEARING 6000ZZSG 2
STOP RING S-10 ..............................................1................REPLACES P/N 080200100
PISTON, 22.4D
PACKING USH-22.4X30X5
STOP RING R-26
BEARING COVER
WASHER, FLAT M10
SHIM 90X110X0.5
PULLEY
WASHER
8
BOLT 8X12 T .....................................................1................REPLACES P/N 001220812
COPPER PACKING 8X16X2
ELBOW 45 DEG. 15-0404
4
10
1
6
1
4
2
1
1
1
4
1
2
1
2
1
1
1
2
1
1
1
1
1
CYLINDER (L)/(AC)
O-RING G-105
1
2
BOLT 10X25 T ...................................................8................REPLACES P/N 001221025
WASHER, LOCK M10
1
1
8
2
BOLT 12X30 T ...................................................1................REPLACES P/N 001221230
WASHER, LOCK M12
BELT COVER (LOWER)
SOCKET HEAD BOLT 8X60 T
1
1
1
1
5 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 41
CONTROl HANDlE ASSY.
page 42 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
2
3
4
5 nO. paRT nO.
1 464343680
456336420
012212035
030212300
031112230
456336400 7
8
9
456449940
456449930
10 001221681
11 032124400
12 025306016
13 0401450160
14 020316130
15 020416100
18 455434950
19 455010030
20 939010060
21 020310080
22 020412070
23 022411635
25 954404230
26 011206020
27 030206150
28 031106100
29 020106050
34 501402870
35 501402880
36 959403460
37 020310080
38 456449980
39 953405260
40 031110160
43 464343690
44 0105050616
45 030206150
46 031106100
47 464457710
48 464457720
CONTROl HANDlE ASSY.
paRT name
HANDLE BRACKET
QTY.
1
REMARKS
HANDLE BRACKET (R) 1
BOLT 12X35 T ...................................................4................REPLACES P/N 001221235
WASHER, LOCK M12
WASHER, FLAT M12
RUBBER COUPLING
SHOCK ABSORBER
2
2
4
4
RUBBER PLATE
BOLT 16X250 T
2
1
CONICAL SPRING WASHER M24 2
SPRING PIN 6X16 ............................................2................REPLACES P/N 025406016
WASHER, FLAT M16 ........................................2................REPLACES P/N 031116260
NUT M16
NUT M16, H=10
SPINDLE
KNOB
SHOCK ABSORBER
1
1
1
1
1
NUT M10, H=6 ..................................................1................REPLACES P/N 020410060
NUT M12, H=7
WING NUT M16
1
1
CLAMP SA120-18 1
BOLT 6X20 T .....................................................1................REPLACES P/N 001220620
WASHER, LOCK M6
WASHER, FLAT M6
1
1
NUT M6 .............................................................1................REPLACES P/N 020306050
HANDLE STOPPER
SPRING/HANDLE (1.4X18X44)
BALL GRIP 32D-M10
1
1
1
NUT M10, H=6 ..................................................1................REPLACES P/N 020410060
RUBBER PACKING 9D-20D-5T
PACKING 1/4 (CU)
WASHER, FLAT M10
HANDLE COVER
WASHER, FLAT M6
PACKING A, HANDLE COVER
PACKING B, HANDLE COVER
1
1
1
1
1
1
BOLT 6X15 T .....................................................6................REPLACES P/N 001220615
WASHER, LOCK M6 6
6 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 43
CONTROl HANDlE ASSY. (CONTINuED)
page 44 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
nO. paRT nO.
61 464117890
64 464216630
65 464457400
66 012010030
67 030210250
68 464216620
69 030210250
70 031110160
71 020310080
72 011208025
73 030208200
80 464457340
81 959403840
82 464457420
83 464457350
84 014208020
85 0401450160
86 458450660
87 033910080
88 464457440
89 464010010
90 011606025
91 020106050
93 464010020
94 001520520
95 58151
96 020305040
99 954002270
101 956100054
103 454010020
104 959021815
104 959021810
CONTROl HANDlE ASSY. (CONTINuED)
paRT name
COLUMN, HANDLE
TRAVEL LEVER
HANDLE BOSS
QTY.
1
1
1
REMARKS
BOLT 10X30 T ...................................................2................REPLACES P/N 001221030
WASHER, LOCK M10 2
1 HANDLE W/GRIP RUBBER
WASHER, LOCK M10
WASHER, FLAT M10
NUT M10
2
2
2
BOLT 8X25 T .....................................................2................REPLACES P/N 001220825
WASHER, LOCK M8
THROTTLE LEVER
BAR GRIP I.D. 12 MM
COVER, THROTTLE
1
1
2
1
ARM, THROTTLE 1
SOCKET HEAD BOLT 8X20 T ..........................1................REPLACES P/N 001520820
WASHER, FLAT M16 ........................................1................REPLACES P/N 031116260
WASHER 16.4-35-0.6
CONICAL SW 16.3 X 31.5 X 1.2
STEEL BALL D6 (SUJ)
DRY BUSHING/ LBF-1620
2
3
1
1
BOLT 6X25 T .....................................................2................REPLACES P/N 001220625
NUT M6 .............................................................2................REPLACES P/N 020306050
ROD END M5
SOCKET HEAD BOLT 5X20 T
NUT M5
OIL HOSE W/SPRING 1/4 X 920
1
1
WASHER, FLAT M5 ..........................................1................REPLACES P/N 031105080
THROTTLE WIRE
CLAMP TC-100
1
1
1
1
SPIRAL TUBE 6D-330L 1
SPIRAL TUBE KEP6/ L=500 ............................1................REPLACES P/N 959021810 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 45
HAND puMp ASSY.
page 46 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
nO. paRT nO.
B% 464910040
C% 464910080
2% 464010040
3% 464010050
4% 464010060
9% 464010070
10% 099205005
11% 464010080
12% 464010090
13% 464010100
14% 458010080
15% 014206020
16#% 050200200
17#% 050210220
18#% 050300380
19# 050200180
22% 464010111
26#% 050300400
27#% 050200150
28#% 050100400
50% 464010120
51% 458451630
52#% 069904010
53#% 069901010
81% 984010060
82% 984010040
83% 984010050
84 464216721
HAND puMp ASSY.
paRT name
ACCUMLATOR
O-RING DUST, SEAL, SET ...............................1................ INCLUDES ITEMS W/#
CONTROL SHAFT
BUSH
CAM
STOPPER
SOCKET HEAD SCREW 5X5 T
PLUG
PIN,STOPPER
PLUG
BREATHER
QTY.
1
1
2
1
2
2
1
2
2
REMARKS
1
SOCKET HEAD BOLT 6X20 T ..........................1................REPLACES P/N 001520620
O-RING P-20 2
O-RING P-22 ....................................................2................REPLACES P/N 050200220
O-RING S-38
O-RING P-18
1
1
ACCUMULATOR CASE .....................................1................S/N N2419 AND ABOVE
O-RING S-40
O-RING P-15
O-RING G-40
SPRING PLUG
BREATHER CAP
1
1
1
1
1
DUST SEAL SER-40 .........................................1................S/N N2419 AND ABOVE
S/N N2419 AND ABOVE DUST SEAL SER-15
SPRING COMPRESSION TOOL
DISASSEMBLING TOOL A
DISASSEMBLING TOOL B
1
1
1
1
HAND PUMP ASSY. ..........................................1................INCLUDES ITEMS W/% mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 47
bATTERY ASSY.
page 48 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
2
3
4
5 nO. paRT nO.
1 464457460
464457470
6
7
8
9
464216660
456447590
456447600
012210020
030210250
955010090
955300490
10 955300470
11 955300480
12 955300460
13 464021020
14 464457410
15 011208025
16 030208200
17 464457390
18 022710809
19 0401450080
20 464343740
bATTERY ASSY.
paRT name
BATTERY CORD (-) 400L
BATTERY CORD (+) 550L
CRADLE, BATTERY
QTY.
1
1
1
REMARKS
RUBBER PLATE (E) 28X240X5
RUBBER PLATE 50X240X10
1
2
SOCKET HEAD BOLT 10X20 T ........................2................REPLACES P/N 001221020
WASHER, LOCK M10
BATTERY 55B24L
BATTERY TERMINAL (-)
TERMINAL COVER (-)
BATTERY TERMINAL (+)
TERMINAL COVER (+)
COVER, BATTERY
FIXED PLATE, BATTERY COVER
2
1
1
1
1
1
1
2
BOLT 8X25 T .....................................................4................REPLACES P/N 001220825
WASHER, LOCK M8
BATTERY BOLT
4
2
NYLON NUT M8 2
WASHER, FLAT M8 ..........................................2................REPLACES P/N 031108160
HOLDER, BATTERY 1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 49
COMpACTION ANAlYZING SYSTEM ASSY. (MVH3O6DSCpAS)
BATTERY CRADLE
23
24
25 page 50 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
COMpACTION ANAlYZING SYSTEM ASSY. (MVH3O6DSCpAS)
nO. paRT nO.
1 465350490 paRT name
COMPACTION SENSOR PANEL
2 464350510 PACKING,SENSOR
5
6
3
4
009110062
952404470
030206150
022710607
7
8
464350500
464464350
9 H5HB051000
10 030205130
11#
12
13
14
15% 464010140
16
959021812
464350390
515450380
464464520
506010070
SPIRAL TUBE 6D-800L
QTY.
1
1
4
4
4
1
2
1
1
1
REMARKS
SOCKET HEAD SCREW 6X20
WASHER, FLAT M6 ...........................................4................REPLACES P/N 031106100
WASHER, LOCK M6
NYLON NUT M6
ACCELERATION SENSOR ASSY. ....................1................INCLUDES ITEMS W/ #
SENSOR HOLDER COVER
SOCKET HEAD BOLT 5X10 T ...........................2................REPLACES P/N 001520510
WASHER, LOCK M5
WIRE HARNESS, SENSOR
WIRE HARNESS
FUSE HOLDER, SENSOR ................................1................INCLUDES ITEMS W/ %
FUSE 2 AMP ......................................................1................MVH306DSCPAS
17 464022020 COVER,BATTERY .............................................1................MVH306DSCPAS ONLY
18 001521030
19 959408330
20 030210250
21 0105091025
22 031110160
23 464457410
24 030208200
25 011208025
CLAMP TC-150
SOCKET HEAD BOLT 10X30 T
WIRE CLIP,SENSOR
WASHER, LOCK M10
WASHER, LOCK M8
7
2
1
3
BOLT 10X25 T....................................................1................REPLACES P/N 001221025
WASHER, FLAT M10
FIXED PLATE, BATTERY COVER
1
2
4
BOLT 8X25 T .....................................................4................REPLACES P/N 001220825 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 51
ElECTRIC DEVICE ASSY.
page 52 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
ElECTRIC DEVICE ASSY.
nO. paRT nO.
1
2
464457460
464457470
24 464459260
26 454010020
28 955300400
30 506010070
41 955300680
41A# 955000010
44 10519878570 paRT name
BATTERY CORD (-) 400L
BATTERY CORD (+) 550L
WIRE CP
IGNITION KEY
HARNESS (C), WIRE
QTY.
1
1
1
REMARKS
CLAMP TC-100
BUZZER (EBL)
3
1
CLAMP TC-150 1
IGNITION SWITCH ASSY. .................................1................INCLUDES ITEMS W/ #
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 53
YANMAR l70V6 — CYlINDER blOCk ASSY.
page 54 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — CYlINDER blOCk ASSY.
nO.
1 paRT nO. paRT name
11421001010 CYLINDER BLOCK ASSY.
5 11439501330 CYLINDER HEAD GASKET ASSY.
11 11435001380 O-RING
12 11429901800 SHIM SET
23 11429901830 COVER (FO PUMP)
24 11425001841 GASKET
25 22312040080 PIN 4X8 STRAIGHT
26 23875020000 PLUG PT 1/4 STEEL
27 11429901600 PIN, 8X12
28 26226060182 STUD M6X18 PLATED
29 26226060222 STUD M6X22 PLATED
30 26366060002 NUT M6
31 11435001412 CRANKCASE GASKET
1
2
1
1
QTY.
1
1
1
REMARKS
1
2
1
2
3
1
32 11421001460 CRANKCASE COVER D ...................................1................INCLUDES ITEMS W/ $
35$ 11435002100 MAIN BEARING US=STD.
37 11429935150 L.O. INLET PIPE
38 26106080352 BOLT M 8X35 PLATED
39 10542501690 PLUG M16
1
1
15
2
40 11469901760 OIL GAUGE CAP, W/LUB ..................................2................INCLUDES ITEMS W/ #
42# 24311000180 O-RING
43 22190160002 SEAL WASHER 16S
44 11429902030 RETAINER
45 11435002113 BALL BEARING
46 16011002220 OIL SEAL
47 16011002220 OIL SEAL
48 24162152116 NEEDLE BEARING
49 26106080122 BOLT M8X12 PLATED
2
2
1
1
1
1
1
1
50 11435002200 MAIN BEARING US=0.25 ..................................1................UNDERSIZED PART
51 11435002210 MAIN BEARING US=0.50 ..................................1................UNDERSIZED PART
52 12125239450 OIL PRESSURE SENDER 1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 55
YANMAR l70V6 — CYlINDER HEAD ASSY.
page 56 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — CYlINDER HEAD ASSY.
nO.
1 paRT nO. paRT name
11421001200 CYLINDER HEAD A BOLT
2
3
7
8
QTY.
2
2
1
1
1
2
2
REMARKS
11421001210 CYLINDER HEAD B BOLT
11421011020 CYLINDER HEAD ASSY.
11421011100 INTAKE VALVE
11421011110 EXHAUST VALVE
9 11421011120 VALVE SPRING
10 11421011180 SPRING RETAINER
11 11421011930 COTTER ASSY. 2
13 11421011250 SUPPORT ASSY. ROCKER ..............................1................INCLUDES ITEMS W/ #
14# 11421011260 ROCKER ARM SUPPORT
15# 11421011280 C TYPE RETAINING PIN
18#+ 11429911240 ADJUSTING SCREW
1
2
16# 11421011650 INTAKE ARM ASSY. .........................................1................INCLUDES ITEMS W/ +
19#+ 26856060002 LOCK NUT 6
1
1
20# 11421011660 EXHAUST ARM ASSY. .....................................1................INCLUDES ITEMS W/ $
22#$ 11429911240 ADJUSTING SCREW
23#$ 26856060002 LOCK NUT 6
24 11435011340 VALVE STEM SEAL
25 11477111461 NOZZLE GASKET
26 11429511470 NOZZLE SPACER
27 10501011490 VALVE CAP
28 11429911600 VALVE SPRING WASHER
29 11421011900 NOZZLE RETAINER
1
1
2
1
1
2
2
1
30 22351040008 SPRING PIN 4X8
31 26106060402 BOLT M6X40 PLATED
32 26226060552 STUD M6X55
33 26366060002 NUT M6
34 11421011310 BONNET GASKET 1
35 11421011950 BONNET HEAD ASSY. ......................................1................INCLUDES ITEMS W/ %
37% 11421003590 DECOMP SHAFT ASSY.
40% 11429903640 DECOMP SPRING
42% 22312030160 PARALLEL PIN 3X16
45 26106060552 BOLT M6X55 PLATED
2
2
1
2
1
1
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 57
YANMAR l70V6 — AIR ClEANER ASSY.
page 58 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — AIR ClEANER ASSY.
nO.
1 paRT nO. paRT name QTY. REMARKS
11421012511 AIR CLEANER ASSY. ........................................1................INCLUDES ITEMS W/#
2# 11421012020 AIR CLEANER BODY
3# 11421012520 AIR CLEANER COVER
4# 11421012560 WING NUT
6# 11421012580 STUD BOLT
7# 11421012590 ELEMENT ASSY.
10# 11421012600 KNOCKING KNOB
11 11429912300 U-NUT
12 11421012210 AIR CLEANER GASKET
13 26106060202 BOLT M6X20 PLATED
14 26226060302 STUD M6X30
1
1
1
1
1
1
3
1
1
3 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 59
YANMAR l70V6 — MufflER ASSY.
page 60 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — MufflER ASSY.
nO. paRT nO. paRT name
15 11429913200 MUFFLER GASKET
16 11439913520 MUFFLER ASSY.
22 26106060142 BOLT M6X14 PLATED
23 26216080182 STUD M8X18 PLATED
24 26366080002 NUT M8
25 11424913600 CLAMP
26 11425213910 EXHAUST DEFECTOR
1
1
2
2
QTY.
1
1
2
REMARKS mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 61
YANMAR l70V6 — CRANkSHAfT AND CAMSHAfT ASSY.
page 62 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — CRANkSHAfT AND CAMSHAfT ASSY.
nO.
1
6
7 paRT nO. paRT name
71421014580 CAMSHAFT ASSY.
11421014200 TAPPET
11421014300 ROLLER TAPPET ASSY.
12 11421014400 PUSH ROD ASSY.
13 71421021740 CRANKSHAFT (D) ASSY.
QTY.
1
2
1
REMARKS
2
1
21 11429921220 NUT 1
22 11439921590 FLYWHEEL (DE) ASSY. .....................................1................INCLUDES ITEM W/ #
25# 11436221600 RING GEAR
26 11429921550 FLYWHEEL WASHER
27 22512040120 KEY 4X12
45 71421028510 BALANCER SHAFT ASSY.
62 26106080202 BOLT M 8X20 PLATED
63 16031014550 WASHER
64 22512070360 KEY 7X36 RR
65 24101062030 BEARING
1
2
1
1
1
1
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 63
YANMAR l70V6 — pISTON ASSY.
page 64 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — pISTON ASSY.
nO. paRT nO. paRT name QTY. REMARKS
28 71421022720 PISTON W/ RINGS STD ....................................1................INCLUDES ITEMS W/#
28 71421022620 PISTON W/RINGS OS = 0.25 ...........................1................INCLUDES ITEMS W/$
28 71421022580 PISTON W/RINGS OS = 0.50 ...........................1................INCLUDES ITEMS W/%
30#
30$
36
71487022502
11487222140
30% 11487222150
11439922300
PISTON RINGS SET = STD.
PISTON RING SET OS = 0.25
PISTON RING SET OS = 0.50
PISTON PIN
41@ 11820023200 ROD BOLT
42@ 11421023600 CRANK PIN BEARING STD.
1
1
1
1
37 22252000210 CIRCLIP 21 2
38 71421023701 CONNECTING ROD ASSY. ...............................1................INCLUDES ITEMS W/@
2
1
42 11421023610 CRANK BEARING PIN U.S. = 0.25 ...................1................UNDERSIZED PART
42 11421023620 CRANK BEARING PIN U.S. = 0.50 ...................1................UNDERSIZED PART
44@ 11438023910 PISTON PIN BUSH 1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 65
YANMAR l70V6 — lub OIl puMp AND GOVERNOR ASSY.
page 66 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — lub OIl puMp AND GOVERNOR ASSY.
nO.
1
7
8 paRT nO. paRT name
11425032010 LUB. OIL PUMP ASSY.
11429932070 LUB. OIL PUMP COVER
11429932570 O-RING COVER
9 22312030160 PARALLEL PIN 3X16
10 26106060122 BOLT M 6X12 PLATED
QTY.
1
1
1
REMARKS
1
3
11 11425035110 LUBE OIL FILTER COMPLETE .........................1................INCLUDES ITEMS W/ $
13$ 24341000224 O-RING 1A S- 22.4
14 26106060162 BOLT M 6X16 PLATED
1
1
15 11421061500 LEVER ASSY. ...................................................1................INCLUDES ITEMS W/ #
27# 22322030200 TAPER PIN 3X20
32# 22322030200 TAPER PIN 3X20
1
1
35 71421061700 GOVERNOR ASSY. ..........................................1................NCLUDES ITEMS W/ +
36+ 11421061290 GOVERNOR WEIGHT ASSY.
41 11429961600 OIL SEAL
42 11477061610 THRUST WASHER
43 11429961190 GOVERNOR WASHER
44 11477161810 PLAIN WASHER 14
45 11477161830 PLATE
46 11429561940 NUT
47 11477166600 FUEL LIMITER ASSY.
48 11477166690 NUT M14
49 11478061090 LEAD
50 22451060000 WIRE 0.6
51 11477061520 NEEDLE BEARING
52 11425266051 REGULATOR HANDLE
54 18336066110 REGULATOR BRACKET
55 11429966250 RETURN SPRING
56 11429966440 ADJUSTING BOLT
57 10522566990 SCREW
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
58 26106060142 BOLT M 6X14 PLATED
59 26106060202 BOLT M 6X20 PLATED
60 26756060002 LOCK NUT M6 PLATED
61 11421066010 REGULATOR SPRING
62 11429966200 RETURN SPRING
65% 11477161960 SPACER
66% 24311000180 O-RING 1A P- 18.0
1
1
1
1
1
1
1
1
63 11477161890 PROTECTOR COMPLETE ................................1................INCLUDES ITEMS W/ % mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 67
YANMAR l70V6 — COOlING AND STARTING DEVICE ASSY.
page 68 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — COOlING AND STARTING DEVICE ASSY.
nO.
1 paRT nO. paRT name
11429945220 TANK GROMMET
2
3
4
5
6
7
8
9
11421045260 SIDE COVER B (13)
11421045270 SIDE COVER A (13)
11421045300 TOP COVER, BLACK (13)
11421045310 DAMPER
11439945320
11435045340
11421045350
26106060082
SEAL RUBBER
CYLINDER COLLAR COVER
TOP COVER SPACER
BOLT M 6X 8 PLATED
10 26106060202 BOLT M 6X 20 PLATED
11 26226060852 BOLT STUD 6X85
12 26366060002 NUT M 6
13 11421045100 FAN CASE (SILVER) (17)
QTY.
5
1
1
1
1
1
5
1
4
4
1
1
1
4
4
REMARKS
14 11429945300 CUSHION RUBBER
15 11429945310 FAN CASE COLLAR
16
17
11429945330
11429945350
FAN CASE SEAL
FAN CASE BOLT
1
4
19 11439976251 RECOIL STARTER (D) ASSY. ...........................1................ INCLUDES ITEMS W/ #
20# 11439976510 STARTER CASE
21# 11439976521 RECOIL REEL
22# 11439976530 RATCHET
23# 11439976540 SPIRAL SPRING
24# 11439976550 RATCHET COVER
25# 11439976560 SPRING
26# 11439976570 RETURN SPRING
27# 11439976580 SCREW
28# 11439976620 STARTER KNOB
29# 11439976630 STARTER ROPE
30 11439976590 STARTER PULLEY
31 26106060082 BOLT M 6X 8 PLATED
32 26106060122 BOLT M 6X 12 PLATED
1
1
1
1
1
1
1
1
1
4
1
1
3 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 69
YANMAR l70V6 — fuEl INJECTION puMp ASSY.
page 70 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — fuEl INJECTION puMp ASSY.
nO.
1 paRT nO. paRT name QTY. REMARKS
71424951400 FUEL INJECTION PUMP ASSY. .......................1................INCLUDES ITEMS W/*
18 71421053100 FUEL INJECTOR ...............................................1................INCLUDES ITEMS W/$
19$ 11421053000 NOZZLE ASSY. 1
1 21$ 11421053080 NOZZLE NUT
23$ 11421053330 PIN
24$ 11421053120 NOZZLE SPRING
25$ 11421053130 SPRING SEAT
26$ 11421053140 VALVE SPACER ASSY.
27$ 11421053410 SHIM (T=1.00)
27 11421053420 SHIM (T=1.05)
27 11421053430 SHIM (T=1.10)
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
11421053440
11421053450
11421053460
11421053470
11421053480
11421053490
11421053500
11421053510
11421053520
11421053530
11421053540
11421053550
11421053560
11421053570
11421053580
11421053590
11421053600
11421053610
SHIM (T=1.15)
SHIM (T=1.20)
SHIM (T=1.25)
SHIM (T=1.30)
SHIM (T=1.35)
SHIM (T=1.40)
SHIM (T=1.45)
SHIM (T=1.50)
SHIM (T=1.55)
SHIM (T=1.60)
SHIM (T=1.65)
SHIM (T=1.70)
SHIM (T=1.75)
SHIM (T=1.80)
SHIM (T=1.85)
SHIM (T=1.90)
SHIM (T=1.95)
SHIM (T=2.00)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 71
YANMAR l70V6 — fuEl TANk AND fuEl lINE ASSY.
SEE FUEL
INJECTION ASSY.
SEE FUEL
INJECTION ASSY.
page 72 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — fuEl TANk AND fuEl lINE ASSY.
nO.
1 paRT nO. paRT name QTY. REMARKS
71424955020 FUEL TANK, BLACK ..........................................1................INCLUDES ITEMS W/@
3@ 11429955080 DRAIN PLUG
4@ 23414080000 PACKING 8
1
1
5@ 11428855041 FUEL TANK CAP ASSY. ....................................1................INCLUDES ITEMS W/+
7@+ 11428855081 CAP VALVE
8 11425055100 FILTER, FUEL
10 11435055150 PIPE GUAGE
11 10385455220 CLAMP
12 11425055201 FUEL TANK DAMPER
13 11423955120 FUEL FILTER .....................................................1................INCLUDES ITEMS W/#
14# 11425055130 GASKET
15 11421055210 FUEL TANK STAY A
22 26106080452 BOLT M 8X 45 PLATED
23 26366060002 NUT M6
25> 11478059060 FUEL OIL PIPE
26> 23080014000 CLAMP 14
1
2
1
1
4
1
1
16 11421055230 FUEL TANK STAY B 1
17 11424055300 FUEL COCK ASSY. ...........................................1................INCLUDES ITEMS W/ $
18$ 24341000150 O-RING 1A S- 15.0
19 11421055810 LIFTING BOLT
20 22117080000 WASHER 8
21 26106060162 BOLT M 6X 16 PLATED
1
2
1
1
1
2
1
2
27 11423959300 RETURN PIPE ASSY. ........................................1................INCLUDES ITEMS W/%
28% 12472259050 CLAMP 9
29% 11465059060
30
31% 11465259310
32% 12175059890
33
39
12406659100
11421059800
11421059850
FUEL RETURN PIPE
CLAMP 8
PROTECT TUBE
RETAINER
FUEL INJECTION PIPE
INJECTION PIPE SUPPORT
1
1
1
1
1
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 73
YANMAR l70V6 — STARTING MOTOR AND DYNAMO ASSY.
page 74 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — STARTING MOTOR AND DYNAMO ASSY.
nO.
1 paRT nO. paRT name QTY. REMARKS
71436277011 STARTER ...........................................................1................INCLUDES ITEMS W/ $
2 $
3 $
4 $
5 $
11438177110
X2114811000
X2114715500
11438177130
ARMATURE
THRUST WASHER KIT
PINION STOPPER SET
FIELD COIL ASSY.
6 $ 11438177140 REAR COVER 1
7 $ 11437177160 BRUSH HOLDER ASSY. ....................................1................INCLUDES ITEMS W/#
8 $# 11437179040 BRUSH (-)
9 $# 11437179050 BRUSH (+)
10 $# 11437179060 BRUSH SPRING
11 $ X211445508 PINION ASSY.
12 $ 11438177151 GEAR HOUSING ASSY.
13 $ 11437177170 DUST COVER KIT
14 $ 11437177180 SHIFT LEVER KIT
15$ 12969877020 MAGNET SWITCH
16 $ 11926077260 THROUGH BOLT
17 $ 11437179070 BOLT M6X37
18 $ 12125477810 TERMINAL COVER
19 26106100302 BOLT M10X30 PLATED
20 26716080002 NUT M8
22 11439978730 STATOR ASSY.
23 11439978740 DYNAMO WHEEL
24 16026078700 CORD CLAMP
25 26106060122 BOLT M6X12 PLATED
1
1
1
1
2
1
4
1
1
1
1
1
2
2
1
2
1
1
1
1
26 26106060202 BOLT M6X20 PLATED
27 26577060152 SCREW M6X15
30 11434077400 HARNESS BRACKET
31 26023040102 SCREW M4X10
3
1
1
3
2
32 11435177540 WIRE HARNESS ..............................................1................INCLUDES ITEMS W/ %
33% 29411200000 CARTRIDGE FUSE 20A
34 11434077710 REGULATOR
35 26106060182 BOLT M6X18 PLATED
36 26106060202 BOLT M6X20 PLATED
37 11435177520 JOINT
2
2
2
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 75
YANMAR l70V6 — TOOl, lAbEl, AND GASkET ASSY.
page 76 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
YANMAR l70V6 — TOOl, lAbEl, AND GASkET ASSY.
nO.
3
4
5
6
7 paRT nO. paRT name
11429907100 AIR COOLED LABEL
11429907110 YANMAR LABEL
11421007120 CAUTION LABEL
11421007130 HOW TO START- E LABEL
11429907160 DIESEL LABEL
QTY.
1
1
1
REMARKS
1
1
8 11421007200 DECOMPRESSION LABEL 1
11 11429992590 TOOL ASSY. .....................................................1................INCLUDES ITEMS W/ %
12% 11429992600 TOOL BAG
13% 11429992710 WRENCH, BOX
14% 11429992720 WRENCH, BOX
15% 11429992730 DRIVER
1
1
1
1
16% 11429992740 FUEL FITTING 1
17 71421092600 GASKET SET (NON- ASB) ................................1................INCLUDES ITEMS W/ #
18# 11439501330 CYLINDER HEAD GASKET ASSY.
24# 11435001380 O-RING
25#
26#
27#
28#
29#
30#
31#
32#
33#
34#
35#
36#
37#
38#
11435001412
24311000180
11425001841
22190160002
11435011340
11477111461
11421011310
11421012210
11429913200
11429932570
24341000100
23414080000
24341000224
24341000150
CRANK CASE GASKET
O-RING
GASKET
WASHER SEAL 16S
VALVE STEM SEAL
NOZZLE GASKET
BONNET GASKET
AIR CLEANER GASKET
MUFFLER GASKET
O-RING COVER
O-RING 1A S- 10.0
PACKING 8
O-RING 1A S- 22.4
O-RING 1A S-15.0
1
1
1
1
1
1
1
1
2
1
1
2
1
2
1
1 mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 77
TERMS AND CONDITIONS Of SAlE — pARTS
paYmenT TeRms
Terms of payment for parts are net 30 days.
FReighT pOLiCY
All parts orders will be shipped collect or prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier.
minimum ORdeR
The minimum charge for orders from Multiquip is $15.00 net. Customers will be asked for instructions regarding handling of orders not meeting this requirement.
ReTuRned gOOds pOLiCY
Return shipments will be accepted and credit will be allowed, subject to the following provisions:
1. A Returned Material Authorization must be approved by Multiquip prior to shipment.
2. To obtain a Return Material Authorization, a list must be provided to Multiquip
Parts Sales that defi nes item numbers, quantities, and descriptions of the items to be returned.
a. The parts numbers and descriptions must match the current parts price list.
b. The list must be typed or computer generated.
c. The list must state the reason(s) for the return.
d. The list must reference the sales order(s) or invoice (s) under which the items were originally purchased.
e. The list must include the name and phone number of the person requesting the RMA.
3. A copy of the Return Material Authorization must accompany the return shipment.
4. Freight is at the sender’s expense. All parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked.
6. The following items are not returnable: a. Obsolete parts. (If an item is in the price book and shows as being replaced by another item, it is obsolete.) b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings, and other rubber parts) that were purchased more than six months prior to the return date.
c. Any line item with an extended dealer net price of less than
$5.00.
d. Special order items.
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
7. The sender will be notifi ed of any material received that is not acceptable.
8. Such material will be held for five working days from notifi cation, pending instructions. If a reply is not received within five days, the material will be returned to the sender at his expense.
9. Credit on returned parts will be issued at dealer net price at time of the original purchase, less a 15% restocking charge.
10. In cases where an item is accepted, for which the original purchase document can not be determined, the price will be based on the list price that was effective twelve months prior to the RMA date.
11. Credit issued will be applied to future purchases only.
pRiCing and ReBaTes
Prices are subject to change without prior notice. Price changes are effective on a specifi c date and all orders received on or after that date will be billed at the revised price.
Rebates for price declines and added charges for price increases will not be made for stock on hand at the time of any price change.
Multiquip reserves the right to quote and sell direct to Government agencies, and to
Original Equipment Manufacturer accounts who use our products as integral parts of their own products.
speCiaL eXpediTing seRviCe
A $35.00 surcharge will be added to the invoice for special handling including bus shipments, insured parcel post or in cases where Multiquip must personally deliver the parts to the carrier.
LimiTaTiOns OF seLLeR’s LiaBiLiTY
Multiquip shall not be liable hereunder for damages in excess of the purchase price of the item with respect to which damages are claimed, and in no event shall Multiquip be liable for loss of profi t or good will or for any other special, consequential or incidental damages.
LimiTaTiOn OF WaRRanTies
No warranties, express or implied, are made in connection with the sale of parts or trade accessories nor as to any engine not manufactured by Multiquip. Such warranties made in connection with the sale of new, complete units are made exclusively by a statement of warranty packaged with such units, and Multiquip neither assumes nor authorizes any person to assume for it any other obligation or liability whatever in connection with the sale of its products. Apart from such written statement of warranty, there are no warranties, express, implied or statutory, which extend beyond the description of the products on the face hereof.
Effective: February 22, 2006 page 78 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)
NOTES
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 79
OperatiOn and parts Manual
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Offi ce
18910 Wilmington Ave.
Carson, CA 90746
Contact : [email protected]
Service Department
800-421-1244
310-537-3700
Technical Assistance
Tel. (800) 421-1244
Fax (310) 537-3927
Fax: 310-537-4259
800-478-1244
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact : [email protected]
Fax: 310-943-2238
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
MQ Parts Department
800-427-1244
310-537-3700
Warranty Department
800-421-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Fax: 310-943-2249
UNITED KINGDOM
Multiquip (UK) Limited Head Offi ce
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfi eld, Cheshire SK16 4UJ
Contact : [email protected]
Tel: 0161 339 2223
Fax: 0161 339 3226
© COPYRIGHT 2014, MULTIQUIP INC.
Multiquip Inc , the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifi cations included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifi cations, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Advertisement
Key Features
- Reversible plate for efficient forward and reverse travel
- High-frequency vibrations for powerful compaction
- Yanmar L70V6 diesel engine for reliable power
- Adjustable handle for operator comfort
- COMPAS system (DSCPAS model) for monitoring soil stiffness
