ORiNG IPS-1042FX-24V Series Quick Installation Manual

Version 1.0
ORing Industrial Networking Corp.
PoE
SWITCH
INDUSTRIAL
Quick Installation Guide
Introduction
IPS-1042FX-24V Series
Specifications
Features
IPS-1042FX-MM-SC-24V
IPS-1042FX-MM-SC-24V
10/100 Base-T(X) Ports in RJ45
Auto MDI/MDIX with P.S.E.
4
Fiber Ports Number
2
Fiber Ports standard
Supports IEEE 802.3at compliant PoE and total power budget is 120Watts with
maximum 30Watts per port
Fiber Diameter (µm)
2
100Base-FX
100Base-FX
Multi-mode
Single-mode
62.5/125 µ m & 50/125 µ m
9/125 µ m
Fiber Mode
Fiber Optical Connector
SC
SC
2 Km
30 Km
Wavelength (nm)
1310 nm
1310 nm
Max. Output Optical Power (dbm)
-14 dbm
-8 dbm
Min. Output Optical Power (dbm)
-23.5 dbm
-15 dbm
Typical Distance (Km)
Max. Input Optical Power (Saturation)
0 dbm
0 dbm
Min. Input Optical Power (Sensitivity)
-31 dbm
-34 dbm
7.5 db
19 db
Link Budget (db)
IPS-1042FX-24V series can be used in connecting several Ethernet devices like
Ethernet I/O, IP-Camera or other Ethernet switches. In addition, there are two
r edundant power inputs at terminal block to avoid interruption caused by power
down. When the primary DC power input fails, the backup power input will take over
immediately to guarantee a non-stop operation.
Physical Ports
IPS-1042FX-24V series provide 4x10/100Base-T(X) PoE (P.S.E.) and 2x100BaseFX single/multi-mode fiber ports
Support auto-negotiation and auto-MDI/MDI-X
Practical Operation
ORing Switch Model
Fiber Ports Specification
IPS-1042FX-24V series are unmanaged PoE Ethernet switches with
4x10/100Base-T(X) P.S.E. and 2x100Base-FX ports. IPS-1042FX-24V series
supports Power over Ethernet, a system to transmit electrical power, along with
data, to remote devices over standard twisted-pair cable in an Ethernet network.
IPS-1042FX-24V series has 4x10/100Base-T(X) P.S.E.Power Sourcing
Equipment) ports. P.S.E. is a device (switch or hub for instance) that will
provide power in a PoE setup. IPS-1042FX-24V series support redundant
power inputs, configurable relay output alarm and rigid IP-30 housing. In addition,
o
the wide operating temperature range from -40 to 70 C can satisfy most of
operating environment.
Industrial Unmanaged PoE Switch
Connections of Ethernet devices
Technology
Support store and forward transmission
Support flow control
Ethernet Standards
IEEE
IEEE
IEEE
IEEE
MAC Table
2048 MAC addresses
Processing
Store-and-Forward
Support surge protection technology
Warning system by relay output
Slim type rigid IP-30 housing design
802.3 for 10Base-T
802.3u for 100Base-TX and 100Base-FX
802.3x for Flow control
802.3at PoE specification (up to 30 Watts per port for P.S.E.)
DIN-Rail and wall mounting enabled
LED Indicators
Power Connection Guide
Front Panel
Power indicator
Green: Power LED x2
Fault indicator
Amber: Indicate PWR1 or PWR2 failure
10/100Base-T(X)RJ45 Port
Indicator
Green for port Link/Act.
Green for PoE power injected.
100Base-FX Fiber Port Indicator
Green for port Link/Act.
Power 2 LED
Fault Contact
！
PWR-2
Warning !!!
24-36Vdc Input only
Check Polarity First.
1A@24V
Relay
PWR-1
G
Power 1 LED
Power Fault LED
P1
Redundant Input power
Dual DC inputs 24~36VDC on 6-pin terminal block
Power consumption(Typ.)
6.48 Watts
(power consumption of P.S.E. is not included)
Overload current protection
Present
Reverse polarity protection
Not Present
Frame Ground
V2- V2+
IPS-1042FX-24V
Relay output to carry capacity of 1A at 24 VDC
Power
V1- V1+
P2 Fault
TX
5.4 Watts
(power consumption of P.S.E. is not included)
6
RX
Fiber Link/Act LED
LINK/ACT
Power
Supply
24-36 VDC
DIP Switch Select for
Power Alarm Relay Output
V-
V+
V+
V-
Power
Supply
24-36VDC
Warning
Device
+24V
Physical Characteristic
Enclosure
IP-30
Dimension (W x D x H)
41.0 (W) x 94.9 (D) x 144.3 (H) mm (1.61 x 3.74 x 5.68 inches)
Weight (g)
395g
TX
Fiber Port
RX
Environmental
GND
Power
Supply
Storage Temperature
-40 to 85 o C (-40 to 185 o F)
Operating Temperature
-40 to 70 o C (-40 to 158 o F)
Operating Humidity
5% to 95% Non-condensing
4
Green: Link/Act
Regulatory Approvals
DIP Switch Function
DIP-2
OFF
OFF
Power failure relay alarm disabled
ON
OFF
PWR-1 failure, relay alarm enabled
OFF
ON
PWR-2 failure, relay alarm enabled
ON
QIG
ON
PWR-1 or PWR-2 failure,
relay alarm enabled
IPS-1042FX-24V Series
1907-2-29-IPS1042FX-0
LAN Port
3
EMI
FCC Part 15, CISPR (EN55022) class A
EMS
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock
IEC60068-2-27
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6
Safety
EN60950-1
Warranty
5 years
Description
DIP-1
5
Green: PoE power injected
2
1
10/100TX
PRINTED ON RECYCLED PAPER
A
Quick Installation Guide
Version 1.0
ORing Industrial Networking Corp.
PoE
SWITCH
INDUSTRIAL
Quick Installation Guide
Installation
IPS-1042FX-24V Series
Communication Connections
Accessory
DIN-Rail Install Step
Wall-mounted Install Step
1
Industrial Unmanaged PoE Switch
6-Pin Terminal block
2
10/100Base-T(X) Ethernet Connection
Dust Cover (RJ-45)
RJ45 (8-pin) to RJ45 (8-Pin) Straight-Through Cable Wiring
Switch Port
Straight-Through Cable
NIC Port
RJ-45
Connector
RJ45 Plug Pin1
RJ-45
Connector
Tx+
TxRx+
Rx-
Rx+
RxTx+
Tx-
3
6
1
2
3
6
1
2
RJ45 (8-pin) to RJ45 (8-Pin) Cross-Over Cable Wiring
3
Round Screw (M3 X3)
Wall-mounted kit
4
Switch Port
(NIC Port)
Cross-Over Cable
Switch Port
(NIC Port)
RJ-45
Connector
RJ45 Plug Pin1
RJ-45
Connector
(Rx+)
(Rx-)
(Tx+)
(Tx-)
Tx+
TxRx+
Rx-
3
6
1
2
1
2
3
6
Rx+
RxTx+
Tx-
(Tx+)
(Tx-)
(Rx+)
(Rx-)
100Base-FX Connection
SC-Port Pinouts
5
40mm DIN-Rail kit
6
SC-Port Pinouts
QIG
SC-Port to SC-Port Cable Wiring
Tx
Rx
Rx
Tx
Tx
SC-Port Pinouts
Packing list
ORing Industrial Networking Corp.
Model name
Cable Wiring
Rx
Rx
SC-Port Pinouts
Tx
Pin Definition
Front Panel
Model Description
10/100Base-T(X) PoE P.S.E.
Port
Accessory
RJ45 Pin Definition
Copyright© 2013 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
IPS-1042FX-MM-SC-24V
Website: www.oring-networking.com
E-mail: [email protected]
IPS-1042FX-SS-SC-24V
QIG
IPS-1042FX-24V Series
I
A
I
A
Industrial 6-port unmanaged PoE Ethernet
switch with 4x10/100Base-T(X) P.S.E. and
2x100Base-FX, multi-mode, 2Km/1310nm,
SC connector, 24VDC power input
Industrial 6-port unmanaged PoE Ethernet
switch with 4x10/100Base-T(X) P.S.E. and
2x100Base-FX, single-mode,
30Km/1310nm, SC connector, 24VDC
power input
1
5
1
5
X 1,
X1,
X 1,
X1,
2
6
2
6
X 4,
X1
X 4,
X1
3
3
X 8,
X 8,
4
4
X 2,
Pin No.
Description
#1
TD+ with PoE Power input +
#2
TD- with PoE Power input +
#3
RD+ with PoE Power input -
#6
RD- with PoE Power input -
X 2,
PRINTED ON RECYCLED PAPER
Quick Installation Guide