NEC MultiSync P401, P461 LCD Monitor Uživatelská příručka
Below you will find brief information for MultiSync P401, MultiSync P461. These monitors offer various connection options (HDMI, DisplayPort, VGA, DVI), adjustable picture settings, and power management features. They also support Picture-in-Picture (PIP) and remote control functionality for convenient operation.
PDF
Document
Advertisement
Advertisement
User’s Manual MultiSync P401 MultiSync P461 Index Declaration of conformity ............................................................................................................................. English-1 Important Information ................................................................................................................................... English-2 WARNING, CAUTION ........................................................................................................................ English-2 Declaration ................................................................................................................................................... English-2 Safety Precautions, Maintenance & Recommended Use ............................................................................ English-3 Contents ....................................................................................................................................................... English-4 Installation .................................................................................................................................................... English-5 Parts Name and Functions .......................................................................................................................... English-7 Control Panel ...................................................................................................................................... English-7 Terminal Panel .................................................................................................................................... English-8 Wireless Remote Control ................................................................................................................... English-10 Operating Range for the Remote Control ........................................................................................... English-11 Handling the remote control ........................................................................................................... English-11 Setup ............................................................................................................................................................ English-12 Connections ................................................................................................................................................. English-14 Wiring Diagram ................................................................................................................................... English-14 Connecting a Personal Computer ...................................................................................................... English-15 Connecting a DVD Player with HDMI out ........................................................................................... English-15 Connecting a Computer with DisplayPort ........................................................................................... English-15 Basic Operation ........................................................................................................................................... English-16 Power ON and OFF Modes ................................................................................................................ English-16 Power Indicator .................................................................................................................................. English-17 Using Power Management ................................................................................................................. English-17 Selecting a video source .................................................................................................................... English-17 Picture Aspect .................................................................................................................................... English-17 Information OSD ................................................................................................................................. English-18 Picture Mode ...................................................................................................................................... English-18 OSD (On-Screen-Display) Controls ............................................................................................................. English-19 PICTURE ............................................................................................................................................ English-20 ADJUST ............................................................................................................................................. English-20 AUDIO ................................................................................................................................................ English-21 SCHEDULE ........................................................................................................................................ English-21 PIP ...................................................................................................................................................... English-22 OSD .................................................................................................................................................... English-22 MULTI DISPLAY ................................................................................................................................. English-23 DISPLAY PROTECTION .................................................................................................................... English-24 ADVANCED OPTION ......................................................................................................................... English-24 Remote Control Function ............................................................................................................................. English-27 Controlling the LCD monitor via RS-232C Remote Control ......................................................................... English-29 Controlling the LCD monitor via LAN Control .............................................................................................. English-30 Features ....................................................................................................................................................... English-33 Troubleshooting ........................................................................................................................................... English-34 Specifications - P401 ................................................................................................................................... English-35 Specifications - P461 ................................................................................................................................... English-36 Pin Assignment ............................................................................................................................................ English-37 Manufacturer’s Recycling and Energy Information ...................................................................................... English-38 www.necdisplaysolutions.com This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: Address: Tel. No.: NEC Display Solutions of America, Inc. 500 Park Boulevard, Suite 1100 Itasca, Illinois 60143 (630) 467-3000 Type of Product: Computer Monitor Equipment Classification: Class B Peripheral Model: MultiSync P401 (L408TM) MultiSync P461 (L468TN) We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specified cables with the MultiSync P401 (L408TM)/MultiSync P461 (L468TN) colour monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied shielded video signal cable, Mini D-SUB 15 pin to Mini D-SUB 15 pin. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland. DisplayPort is trademarks of Video Electronics Standards Association. All other brands and product names are trademarks or registered trademarks of their respective owners. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. English-1 English DECLARATION OF CONFORMITY Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country. North America European Continental U.K. Chinese Japanese Region U.S.A./Canada EU (except U.K.) U.K. China Japan Voltage 120* 230 230 220 100 Plug Type Plug Shape *When operating the MultiSync P401 (L408TM)/MultiSync P461 (L468TN) monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE: This product can only be serviced in the country where it was purchased. Declaration Declaration of the Manufacturer We hereby certify that the color monitor MultiSync P401 (L408TM)/MultiSync P461 (L468TN) are in compliance with and marked with Council Directive 2006/95/EC: – EN 60950-1 Council Directive 2004/108/EC: – EN 55022 – EN 61000-3-2 – EN 61000-3-3 – EN 55024 NEC Display Solutions, Ltd. 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, Japan English-2 • • • • • FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTI-FUNCTION MONITOR: Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • When the power supply cord or plug is damaged. • If liquid has been spilled, or objects have fallen into the monitor. • If the monitor has been exposed to rain or water. • If the monitor has been dropped or the cabinet damaged. • If you notice any structural damage such as cracks or unnatural wobbling. • If the monitor does not operate normally by following operating instructions. Do not spill any liquids into the cabinet or use your monitor near water. Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or fatal or may cause electric shock, fire or equipment failure. Recommended Use Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire. Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to the monitor. • For optimum performance, allow 20 minutes for warm-up. • Rest your eyes periodically by focusing on an object at least 5 feet away. Blink often. • Position the monitor at a 90° angle to windows and other light sources to minimize glare and reflections. • Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any cleaning solution or glass cleaner! • The power supply cord you use must have been approved by and comply with the safety standards of your country. (Type H05VV-F 3G 1mm2 should be used in Europe) • In UK, use a BS-approved power cord with molded plug having a black (13A) fuse installed for use with this monitor. • Adjust the monitor’s brightness, contrast and sharpness controls to enhance readability. • Do not place any objects onto the monitor and do not use the monitor outdoors. • • The lamps in this product contain mercury. Please dispose according to state, local or federal law. Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after image effects). • Get regular eye checkups. • Do not bend, crimp or otherwise damage the power cord. Ergonomics • If glass is broken, handle with care. • Do not cover vent on monitor. To realize the maximum ergonomic benefits, we recommend the following: • Do not use monitor in high temperature, humid, dusty, or oily areas. • Use the preset Size and Position controls with standard signals. • If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care. • Use the preset Color Setting. • Use non-interlaced signals. • Allow adequate ventilation around the monitor, so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. Do not put anything on top of the monitor. • Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient contrast. • The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet, which is easily accessible. • Cleaning the LCD Panel • When the liquid crystal panel is stained with dust or dirt, please wipe with soft cloth gently. Handle with care when transporting. Save packaging for transporting. • Please do not rub the LCD panel with hard material. • Please do not apply pressure to the LCD surface. • Please clean the holes of back cabinet to reject dirt and dust at least once a year because of set reliability. • Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface. • When using a LAN cable, do not connect to a peripheral device with wiring that might have excessive voltage. Cleaning the Cabinet Connecting to a TV* • Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. • The screen of the coaxial cable is intended to be connected to earth in the building installation. • Unplug the power supply • Gently wipe the cabinet with a soft cloth • To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth. NOTE: DO NOT clean with benzene thinner, alkaline detergent, alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Rubber or vinyl should not be in contact with the cabinet for an extended period of time. These types of fluids and materials can cause the paint to deteriorate, crack or peel. * The product you purchased may not have this feature. English-3 English Safety Precautions, Maintenance & Recommended Use Contents Your new MultiSync monitor box* should contain the following: • LCD monitor • Cable cover • Power cord*1 • Clamp x 3 • Video Signal Cable • Screw (M4 x 10) x 9 • Wireless Remote Control and AA Batteries • CD-ROM • Setup Manual • Thumbscrew for optional stand x 2 Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Screw (M4 x 10) x 9 Power Cord*1 Thumbscrew for optional stand x 2 Cable cover Setup Manual Clamp x 3 CD-ROM Setup Manual Wireless Remote Control and AA Batteries *1 Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country. * Remember to save your original box and packing material to transport or ship the monitor. English-4 This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty. English Installation Orientation • When using the display in the portrait position, the monitor should be rotated clockwise so that the left side is moved to the top and the LED indicator light is on the bottom. This will allow for proper ventilation and will extend the lifetime of the monitor. Improper ventilation may shorten the lifetime of the monitor. Mounting DO NOT mount the monitor yourself. Please ask dealer. For proper installation it is strongly recommended to use a trained, qualified technician. Please inspect the location where the unit is to be mounted. Mounting on wall or ceiling is the customer’s responsibility. Not all walls or ceilings are capable of supporting the weight of the unit. Product warranty does not cover damage caused by improper installation, remodelling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty. DO NOT block ventilated openings with mounting accessories or other accessories. LED Indicator For NEC Qualified Personnel: To insure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location. • The ceiling and wall must be strong enough to support the monitor and mounting accessories. • DO NOT install in locations where a door or gate can hit the unit. • DO NOT install in areas where the unit will be subjected to strong vibrations and dust. • DO NOT install near where the main power supply enters the building. Mounting Bracket • Do not install in where people can easily grab and hang onto the unit or the mounting apparatus. Washer • When mounting in a recessed area, as in a wall, leave at least 4 inches (10cm) of space between the monitor and the wall for proper ventilation. • Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus. Please note the following when mounting on wall or ceiling • • • • When using mounting accessories other than those that are NEC approved, they must comply with the VESAcompatible (FDMlv1) mounting method. NEC strongly recommends using size M6 screws (11-12 mm + thickness of bracket and washer in length). If using screws longer than 11-12 mm, check the depth of the hole. (Recommended Fasten Force: 470 - 635N•cm) NEC recommends mounting interfaces that comply with UL1678 standard in North America. Unit Mounting location Screw 11-12 mm Thickness of bracket and washer Screw length should equal depth of hole (11-12 mm) + the thickness of mounting bracket and washer. Prior to mounting, inspect the installation location to insure that it is strong enough to support the weight of the unit so that the unit will be safe from harm. Refer to the instructions included with the mounting equipment for detailed information. Mounting on ceiling • Ensure that the ceiling is sturdy enough to support the weight of the unit and the mounting apparatus over time, against earthquakes, unexpected vibrations, and other external forces. • Be sure the unit is mounted to a solid structure within the ceiling, such as a support beam. Secure the monitor using bolts, spring lock washers, washer and nut. • DO NOT mount to areas that have no supporting internal structure. DO NOT use wood screws or anchor screws for mounting. DO NOT mount the unit to trim or to hanging fixtures. Maintenance • Periodically check for loose screws, gaps, distortions, or other problems that may occur with the mounting apparatus. If a problem is detected, please refer to qualified personnel for service. • Regularly check the mounting location for signs of damage or weakness that may occur over time. English-5 Attaching Mounting Accessories 3. Ventilation Requirements The display is designed for use with the VESA mounting system. When mounting in an enclosed space or recessed area, leave adequate room between the monitor and the enclosure to allow heat to disperse, as shown below. 1. Attach Mounting Accessories Be careful to avoid tipping monitor when attaching accessories. VESA Mounting Interface Mounting accessories can be attached with the monitor in the face down position. To avoid damaging the screen face, place the protective sheet on the table underneath the LCD. The protective sheet was wrapped around the LCD in the original packaging. Make sure there is nothing on the table that can damage the monitor. When using mounting accessories other than NEC compliant and approved, they must comply with the VESAcompatible mounting method. Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus; especially when you use monitors in multiple screen. 4. Prevent Tipping When using the display with the Tabletop Stand fasten the LCD to a wall using a cord or chain that can support the weight of the monitor in order to prevent the monitor from falling. Fasten the cord or chain to the monitor using the provided clamps and screws. 278 mm (P401) 304 mm (P461) 2. Installing and removing optional table top stand Screw Holes CAUTION: Installing and removing the stand must be done by two or more people. To install, follow those instructions included with the stand or mounting apparatus. Use only those devices recommended by the manufacturer. Cord or chain Handle with care when mounting LCD monitor stand and avoid pinching your fingers. Clamp Optional table top stand Screw Before attaching the LCD monitor to the wall, make sure that the wall can support the weight of the monitor. Be sure to remove the cord or chain from the wall before moving the LCD. Table Protective Sheet NOTE: Place stand onto monitor so that the long end of the feet are in the front. English-6 English Parts Name and Functions Control Panel POWER button EXIT button Switches the power on/off. See also page 16. Activates the OSD menu when the OSD menu is turned-off. Acts as EXIT button within the OSD to move to previous menu. MUTE button Switches the audio mute ON/OFF. Remote control sensor and Power Indicator INPUT button Acts as SET button within OSD menu. (Toggle switches between [DVI], [DPORT], [VGA], [RGB/HV], [HDMI], [DVD/HD1], [DVD/HD2], [SCART], [VIDEO1], [VIDEO2], [S-VIDEO] or [TV]*). These are available input only, shown as their factory preset name. PLUS button Acts as (+) button to increase the adjustment with OSD menu. Increases the audio output level when the OSD menu is turned off. Receives the signal from the remote control (when using the wireless remote control). See also page 11. Glows green when the LCD monitor is in active mode*. Glows red when the LCD is in POWER OFF (ECO standby) mode. Glows amber when the LCD is in POWER OFF (standby) mode. Blinks amber when the monitor is in Power Save Mode. Green and Amber blink alternately while in Power Standby mode with the “SCHEDULE SETTINGS” function enabled. When a component failure is detected within the monitor, the indicator will blink red. * If “OFF” is selected in “POWER INDICATOR” (see page 23), LED will not light when the LCD monitor is in active mode. AMBIENT LIGHT SENSOR MINUS button Acts as (-) button to decrease the adjustment with OSD menu. Decreases the audio output level when the OSD menu is turned off. UP button Detects the level of ambient light, allowing the monitor to make automatic adjustments to the brightness setting, resulting in a more comfortable viewing experience. Do not cover this sensor. See page 18. Control Key Lock Mode Activates the OSD menu when the OSD menu is turned-off. Acts as button to move the highlighted area up to select adjustment items within OSD menu. DOWN button Activates the OSD menu when the OSD menu is turned-off. Acts as button to move the highlighted area down to select adjustment items within OSD menu. This control completely locks out access to all Control Key functions. To activate the control key lock function, press both and and hold down simultaneously for more than 3 seconds. To resume user mode, press both and and hold simultaneously for more than 3 seconds. *: The product you purchased may not have this feature. English-7 Terminal Panel In Out In Main Power Switch Out VIDEO IN connector (BNC and RCA) On/Off switch to turn main power ON/OFF. To input a composite video signal. BNC and RCA connectors are not available at the same time (Use only one input). AC IN connector VIDEO OUT connector (BNC) Connects with the supplied power cord. To output the composite video signal from the VIDEO IN connector. DISPLAYPORT connector To input DisplayPort signals. DVD/HD connector (RCA) HDMI connector Connecting equipment such as a DVD player, HDTV device, or Set-Top-Box. To input digital HDMI signals. S-VIDEO IN connector (Mini DIN 4 pin) DVI IN (DVI-D) To input digital RGB signals from a computer or HDTV device having a digital RGB output. To input the S-video (Y/C separate signal). * This connector does not support analog input. To input audio signal from external equipment such as a computer, VCR or DVD player. AUDIO IN 1, 2, 3 VGA IN (mini D-Sub 15 pin) AUDIO OUT To input analog RGB signals from a personal computer or from other RGB equipment. To output the audio signal from the AUDIO IN 1, 2, 3, DPORT, HDMI, and TV jack to an external device (stereo receiver, amplifier, etc.). RGB/HV IN [R, G, B, H, V] (BNC) To input analog RGB signals or signals from other RGB equipment. This is also to connect equipment such as a DVD player, HDTV device and Set-Top-Box. A Sync-on-Green signal can be connected to the G connector. This input can be used with an RGB, DVD/HD or Video source. Please select signal type in TERMINAL SETTING. RGB/HV DVD/HD2 VIDEO2 R G B H V R G B H V Pr Y Pb EXTERNAL CONTROL (D-Sub 9 pin) IN connector: Connect RS-232C input from external equipment such as a PC in order to control RS-232C functions. OUT connector: Connect RS-232C output. To connect multiple MultiSync monitors via RS-232C daisy Chain. LAN port (RJ-45) LAN connection. See page 30. VIDEO REMOTE IN/OUT RGB/HV OUT (BNC) To output the signal from the RGB/HV IN connector or VGA IN connector which is on screen to an input on a separate device. If both signals are not on screen, outputs the signal from RGB/HV IN connector. Use the optional wired remote control by connecting it to your monitor. NOTE: When you use Remote IN/OUT, IR CONTROL in OSD menu should be NORMAL. English-8 English Kensington Lock For security and theft prevention. EXTERNAL SPEAKER TERMINAL To output the audio signal from AUDIO 1, 2, 3, DPORT, HDMI and TV jack. Note: This speaker terminal is for 15W + 15W (8 ohm) speaker. Option board slot Slot for board accessories. Please contact your supplier for detail information. English-9 Wireless Remote Control KEYPAD Press buttons to set and change passwords, change channel and set REMOTE ID. ENT button* Sets channels. DISPLAY button Turns on/off the information OSD. See page 18. MENU button Turns on/off the menu mode. AUTO SETUP button Enters auto setup menu. See page 20. EXIT button Returns to previous menu within OSD menu. UP/DOWN button button to move the highlighted area up or Acts as down to select adjustment items within OSD menu. Small screen which adjusted “PIP” mode moves up or down. MINUS/PLUS (+/-) button Increases or decreases the adjustment level within OSD menu settings. Small screen which adjusted “PIP” mode moves left or right. SET button Makes selection. POWER button VOLUME UP/DOWN button Switches the power on/standby. Increases or decreases audio output level. INPUT button CH +/- button* Selects input signal. DVI: DVI DISPLAYPORT: DPORT VGA: VGA RGB/HV: RGB/HV HDMI: HDMI DVD/HD: DVD/HD1, DVD/HD2, SCART VIDEO: VIDEO1, VIDEO2 S-VIDEO: S-VIDEO OPTION: Depends on your connection Moves channel up or down (For U.S.). GUIDE button* Enters on screen program guide (For U.S.). MUTE button Turns on/off mute function. STILL button ON/OFF button: Activates/deactivates still picture mode. STILL CAPTURE button: Captures still picture. PICTURE MODE button Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1], [AMBIENT2]. See page 18. HIGHBRIGHT: for moving images such as DVD. STANDARD: for images. sRGB: for text based images. CINEMA: for movies. AMBIENT1 and AMBIENT2: activate auto dimming function. See page 18. PIP (Picture In Picture) button ON/OFF button: Toggle switches between PIP, POP, sideby-side (aspect) and side-by-side (full). See page 22. INPUT button: Selects the “picture in picture” input signal. CHANGE button: Replaces to the main picture and sub picture. Sub picture Selects picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See page 17. SOUND button Artificial surround sound. Main picture ASPECT button DVI DPORT VGA RGB/HV HDMI DVD/HD1 DVD/HD2 SCART VIDEO1 VIDEO2 S-VIDEO DVI DPORT VGA RGB/HV HDMI DVD/HD1 DVD/HD2 SCART VIDEO1 VIDEO2 S-VIDEO - *: The product you purchased may not have this feature. English-10 MTS button* Multichannel television sound. AUDIO INPUT button Selects audio input source [IN1], [IN2], [IN3], [HDMI], [DPORT], [TV]*. Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor’s remote sensor during button operation. Use the remote control within a distance of about 7 m (23 ft.) from remote control sensor or at a horizontal and vertical angle of within 30° within a distance of about 3.5 m (10 ft.). button* Activates closed captioning (For U.S.). *: The product you purchased may not have this feature. Caution: Important, the remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor or when there is an object in the path. Handling the remote control • Do not subject to strong shock. • Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately. • Avoid exposure to heat and steam. • Other than to install the batteries, do not open the remote control. English-11 English REMOTE ID button Activates REMOTE ID function. Setup 1. Determine the installation location NEC recommends the following battery use: CAUTION: Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. • Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment. • Do not mix battery brands. CAUTION: MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE. Failure to follow this caution may result in injury if the LCD monitor falls. • Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries. • Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment. CAUTION: Do not mount or operate the display upside down, face up, or face down. • Do not touch exposed battery acid, it may injure skin. CAUTION: This LCD has a temperature sensor and cooling fan. If the LCD becomes too hot, the cooling fan will turn on automatically. If the LCD becomes overheated while the cooling fan is running, a “Caution” warning will appear. If the “Caution” warning appears, discontinue use and allow the unit to cool. Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and “Image Persistance”. If the LCD is used in an enclosed area or if the LCD panel is covered with a protective screen, please check the inside temperature of the monitor by using the “HEAT STATUS” control in the OSD (see page 24). If the temperature is higher than the normal operating temperature, please turn the cooling fan to ON within the FAN CONTROL menu within the OSD (see page 24). IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel. 2. Install the remote control batteries NOTE: If you do not intend to use the Remote Control for a long period of time, remove the batteries. 3. Connect external equipment (See pages 14 and 15) • To protect the external equipment; turn off the main power before making connections. • Refer to your equipment user manual for further information. NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. 4. Connect the supplied power cord • The equipment should be installed close to an easily accessible power outlet. • Please fasten power cord to the LCD monitor by attaching the screw and clamp. • Fully insert the prongs into the power outlet socket. A loose connection may cause image degradation. NOTE: Please refer to the “Safety Precautions and Maintenance” section of this manual for proper selection of AC power cord. Screw The remote control is powered by two 1.5V AA batteries. To install or replace batteries: A. Press and slide to open the cover. B. Align the batteries according to the (+) and (–) indications inside the case. C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. English-12 Clamp • English 5. Attach the cable cover Use six of the M4 x 10 screws (included) to attach the cable cover. 6. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first. 7. Operate the attached external equipment Display the signal from the desired input source. 8. Adjust the sound Make volume adjustments when required. 9. Adjust the screen (See pages 20 and 21) Make adjustments of the screen display position when necessary. 10. Adjust the image (See page 20) Make adjustments such as brightness or contrast when required. 11. Recommended Adjustments To reduce the risk of the “Image Persistence”, please adjust the following items based on the application being used: “SCREEN SAVER”, “SIDE BORDER COLOR” (See page 24) “DATE & TIME”, “SCHEDULE SETTINGS” (See page 21). It is recommended that the “FAN CONTROL” setting (See page 24) be turned to ON also. English-13 Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment. Wiring Diagram DVD player with HDMI out DVD player Stereo Amplifier VCR or DVD Player Computer (Analog) Connected equipment AV PC Media Player Second monitor DVD player with SCART OUT Computer (Digital) Connecting terminal DVD/HD1 (3RCA) Setting in Terminal Mode Input signal name DVD/HD1 Connecting Audio terminal AUDIO IN1, IN2, IN3 DVI (DVI-D) DVI MODE: DVI-HD DVI AUDIO IN1, IN2, IN3 DVI HDMI RAW/EXPAND*1 HDMI HDMI HDMI DVD/HD+VIDEO SCART: ON SCART AUDIO IN1, IN2, IN3 DVD/HD VIDEO1 (BNC&RCA) - VIDEO1 AUDIO IN1, IN2, IN3 VIDEO S-VIDEO - S-VIDEO AUDIO IN1, IN2, IN3 S-VIDEO - Input button in remote control DVD/HD VIDEO2 (5BNC) BNC MODE: VIDEO VIDEO2 AUDIO IN1, IN2, IN3 VIDEO DVD/HD2 (5BNC) BNC MODE: COMPONENT DVD/HD2 AUDIO IN1, IN2, IN3 DVD/HD VGA (D-Sub) - VGA AUDIO IN1, IN2, IN3 VGA DVI (DVI-D) DVI MODE: DVI-PC DVI AUDIO IN1, IN2, IN3 DVI RGB/HV (5BNC) BNC MODE: RGB RGB/HV AUDIO IN1, IN2, IN3 RGB/HV DisplayPort - DPORT DPORT DISPLAYPORT DVI (DVI-D) DVI MODE: DVI-PC DVI AUDIO IN1 DVI *1: depend on signal type. • AUDIO IN 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] in AUDIO INPUT in OSD menu or press the AUDIO INPUT button (remote control). English-14 Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards and a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. <Factory preset signal timing> Resolution 640 x 480 800 x 600 1024 x 768 1280 x 768 1360 x 768 1280 x 1024 1600 x 1200 1920 x 1080 • Scanning frequency Horizontal Vertical 31.5kHz 60Hz 37.9kHz 60Hz 48.4kHz 60Hz 48kHz 60Hz 48kHz 60Hz 64kHz 60Hz 75kHz 60Hz 66.6kHz 60Hz Remarks Compressed image Recommended resolution If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook. Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any special identification or configuration your monitor’s image and monitor may require. • Input TMDS signals conforming to DVI standards. • To maintain display quality, use a cable that conforms to DVI standards. Connecting a DVD Player with HDMI out • Please use an HDMI cable with HDMI logo. • It may take a moment for the signal to appear. • PC-DVI signals are not supported. Connecting a Computer with DisplayPort • Please use Display port cable with DisplayPort certified logo. • It may take a moment for the signal to appear. • Please note that DisplayPort connector does not supply power to the connected component. • Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear. • Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock. English-15 English Connecting a Personal Computer Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD. OFF Main Power Switch ON Power Button Using the remote control English-16 Mode Power ON Power OFF (Eco Standby)*1 Power consumption under 0.5W*3 Power OFF (Standby) Power consumption under 1W*3, *4 Power Save Power consumption under 2W*3, *5 Power Standby when “SCHEDULE SETTINGS” enabled Diagnosis (Detecting failure) Picture Aspect DVI, VGA, RGB/HV, DPORT Status Indicator Light Green*2 Red FULL ZOOM NORMAL HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* Amber FULL Amber Blinking Green and Amber blink alternately WIDE Aspect ratio of image To view a video source: ZOOM (DYNAMIC) Squeeze The LCD monitor follows the VESA approved DPM Display Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period. The power management feature on your new display has been set to the “ON” mode. This allows your display to enter a Power Saving Mode when no signal is applied. This could potentially increase the life and decrease the power consumption of the display. Selecting a video source 4:3 Recommended selection for picture aspect*6 NORMAL FULL Using Power Management NOTE: Depending on the PC and video card used, this function may not operate. NORMAL Unchanged view*6 Red Blinking (See Troubleshooting page 34) *1 When in Eco Standby Mode DDC/CI control does not function. *2 If “OFF” is selected in POWER INDICATOR (page 23), the LED will not light when the LCD monitor is in active mode. *3 “RS-232C” is selected in EXTERNAL CONTROL. *4 DDC/CI should be disabled. *5 No DisplayPort connection. ZOOM WIDE Letterbox *6 Grey areas indicate unused portions of the screen. NORMAL: Displays the aspect ratio the same as it is sent from the source. FULL: Fills entire screen. WIDE: Expands a 16:9 letter box signal to fill entire screen. ZOOM (DYNAMIC): Expands a 4:3 pictures to fill the entire screen with non-linearity. Some of the outside image area will be cut off due to expansion. ZOOM The image can be expanded beyond the active display area. The image which is outside of active display area is not shown. Use the input button to set [VIDEO]. ZOOM Use the COLOR SYSTEM menu to set [AUTO], [NTSC], [PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format. ZOOM *: The product you purchased may not have this feature. English-17 English Power Indicator Information OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. ID number assigned to current monitor*7 ID number assigned monitor to be controlled via RS-232C*8 Input Name Audio input mode Picture aspect Input Signal Information Sub picture information *7: “IR CONTROL” should be set “Primary” or “Secondary”. *8: “IR CONTROL” should be set “Primary”. Picture Mode DVI, VGA, RGB/HV, DPORT STANDARD sRGB AMBIENT1 AMBIENT2 HIGHBRIGHT HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* STANDARD CINEMA AMBIENT1 AMBIENT2 HIGHBRIGHT AMBIENT Mode The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions. NOTE: When picture mode is set to AMBIENT1 or AMBIENT2, BRIGHTNESS, AUTO BRIGHTNESS and BRIGHTNESS in SCREEN SAVER function are disabled. Do not cover anbibrint sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE. AMBIENT parameter setting PICTURE MODE in OSD, select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode. IN BRIGHT: This is the brightness level that the monitor will go up to when the ambient light level is highest. IN DARK: This is the level of brightness that the monitor will go down to when the ambient light level is low. When the AMBIENT function is enabled the Brightness level of the screen changes automatically according to the lighting conditions of the room (Figure 1). Factory Setting BRIGHTNESS range BRIGHTNESS level set for the monitor to use when ambient lighting level is low. BRIGHTNESS level set for the monitor to use when ambient lighting level is high. IN DARK dark IN BRIGHT room bright condition bright Screen Brightness value by AMBIENT1 mode Screen Brightness value by AMBIENT2 mode Figure 1 IN DARK: BRIGHTNESS level set for the monitor to use when ambient lighting level is low. IN BRIGHT: BRIGHTNESS level set for the monitor to use when ambient lighting level is high. *: The product you purchased may not have this feature. English-18 English OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item 70 50 50 50 50 50 Sub Menu THANK YOU FOR SAVING THE ENVIRONMENT. CARBON FOOTPRINT 86.0 % PICTURE MODE Select Adjustment Settings Goto Adjustment Return Close Key Guide Press UP or DOWN button to select sub-menu. Press SET. Press UP or DOWN, PLUS or MINUS to select the function or setting to be adjusted. Press MENU or EXIT. Press UP or DOWN button to select. Press INPUT button to decide. Press UP or DOWN, PLUS or MINUS button to select. Press EXIT Remote Control Control Panel OSD screen English-19 Setting Default PICTURE BRIGHTNESS Adjusts the overall image and background brightness. Press + or - to adjust. Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot changed. 70 CONTRAST Adjusts the image brightness in relationship to the background. Press + or - to adjust. Note: The sRGB picture mode is standard and cannot be changed. 50 SHARPNESS Adjusts the crispness of the image. Press + or - to adjust. BLACK LEVEL Adjusts the image brightness in relationship to the background. Press + or - to adjust. Note: The sRGB picture mode is standard and cannot be changed. 50 TINT Adjusts the tint of the screen. Press + or - to adjust. Note: The sRGB picture mode is standard and cannot be changed. 50 COLOR Adjusts the color depth of the screen. Press + or - to adjust. Note: The sRGB picture mode is standard and cannot be changed. 50*2 COLOR TEMPERATURE Adjusts the color temperature of the entire screen. A low color temperature will make the screen reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further adjustment, the individual R/ G/ B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM must be showing as the COLOR TEMP selection. Note: The sRGB picture mode is set to a predefined 6500 K standard and cannot be changed. COLOR CONTROL Adjusts the levels of the Red, Yellow, Green, Cyan, Blue, Magenta and Saturation. Note: The sRGB picture mode is standard and cannot be changed. GAMMA SELECTION Select a display gamma for best picture quality. Note: The sRGB picture mode is standard and cannot be changed. 50*2 10000K 0 NATIVE*2 (except sRGB setting) NATIVE Gamma correction is handled by the LCD panel. 2.2 Typical display gamma for use with a PC. 2.4 Good for video (TV, DVD, etc.) S GAMMA Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the image (S-Curve). DICOM SIM. DICOM GSDF curve simulated for LCD type. PROGRAMMABLE A programmable gamma curve can be loaded using NEC optional software. MOVIE SETTINGS NOISE REDUCTION 6*2 Adjusts the amount of noise reduction. Press + or - to adjust. TV, VIDEO1, VIDEO2, S-VIDEO inputs only FILM MODE AUTO*2 Selects Film mode. HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast. OFF HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only PICTURE MODE Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1] or [AMBIENT2]. See page 18. STANDARD PICTURE RESET Resets the following settings within the PICTURE menu back to factory setting: BRIGHTNESS, CONTRAST, SHARPNESS, BLACK LEVEL, TINT, COLOR, COLOR TEMPERATURE, COLOR CONTROL , GAMMA SELECTION, MOVIE SETTINGS. - Automatically adjusts Screen Size, H position, V position, Clock, Clock Phase and White Level. - ADJUST AUTO SETUP VGA, RGB/HV inputs only AUTO ADJUST H Position, V Position and Clock Phase are adjusted automatically upon power on. OFF VGA, RGB/HV inputs only H POSITION Controls the horizontal position of the image within the Display area of the LCD. Press + to move right. Press - to move left. - Controls the vertical position of the image within the Display area of the LCD. Press + to move up. Press - to move down. - Press + to expand the width of the image on the right of the screen. Press - to narrow the width of the image on the left. - VGA, RGB/HV inputs only CLOCK PHASE Adjusts the visual “noise” on the image. - All inputs except DVI, HDMI, DPORT V POSITION All inputs except DVI, HDMI, DPORT CLOCK VGA, RGB/HV, DVD/HD1, DVD/HD2, SCART inputs only *: The product you purchased may not have this feature. *2: depends on signal input English-20 Adjusts the horizontal size of the image. - Adjusts the vertical size of the image. - VGA, RGB/HV inputs only V RESOLUTION VGA, RGB/HV inputs only INPUT RESOLUTION VGA, RGB/HV inputs only If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. After selection, execute “AUTO SETUP” if required. If no problem is detected, the only available option will be “AUTO”. ZOOM MODE Select the aspect ratio of the screen image. AUTO - All inputs except TV* BASE ZOOM 16:9 CUSTOM For input sources that have a 16:9 aspect ratio. HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only 14:9 For input sources that have a 14:9 aspect ratio. HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only DYNAMIC Expands 4:3 picture to fill the screen. Some of the image is lost due to expansion. HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only OFF All inputs, except TV* Selecting “OFF” will display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080 resolution, the image will be scaled down to fit the screen.) CUSTOM Displays an image as large as possible without changing the aspect ration. All inputs, except TV* ZOOM** Maintains the aspect ratio while zooming. 1.00 H ZOOM** Amount of horizontal zoom. Can be adjusted for each BASE ZOOM setting. 1.00 V ZOOM** Amount of vertical zoom. Can be adjusted for each BASE ZOOM setting. 1.00 H POS** Horizontal position. Can be adjusted for each BASE ZOOM setting. 0% V POS** Vertical position. Can be adjusted for each BASE ZOOM setting. 0% ASPECT Selects picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See page 17. FULL ADJUST RESET Resets the following settings within the ADJUST menu back to factory setting: AUTO ADJUST, H POSITION, V POSITION, CLOCK, CLOCK PHASE, H RESOLUTION, V RESOLUTION, ZOOM MODE, ASPECT. - AUDIO BALANCE CENTER TREBLE 0 BASS 0 PIP AUDIO Selects source of PIP audio. MAIN AUDIO LINE OUT Selecting “VARIABLE” will enable to control line out level with VOLUME button. SURROUND Artificial surround sound. AUDIO INPUT Selects audio input source [IN1], [IN2], [IN3], [DPORT], [HDMI], [TV]*. AUDIO RESET Resets “AUDIO” options back to factory settings. FIXED OFF Depend on signal input - SCHEDULE OFF TIMER Sets the monitor to power off after a length of time. A time between 1 to 24 hours is available. OFF SCHEDULE SETTINGS Creates a working schedule for the monitor to use. - SCHEDULE LIST List of schedules. - DATE & TIME Sets the date, time, and daylight saving region. Date & time must be set in order for the “SCHEDULE” function to operate. See page 26. YEAR - MONTH - DAY - TIME - DAYLIGHT SAVING OFF *: The product you purchased may not have this feature. **: 16:9, 14:9, CUSTOM only English-21 English H RESOLUTION SCHEDULE RESET Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS. - PIP KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD. OFF PIP MODE Picture-in-Picture OFF OFF OFF PIP PIP POP POP SIDE BY SIDE (ASPECT) SIDE BY SIDE ASPECT SIDE BY SIDE (FULL) PIP SIZE SIDE BY SIDE FULL Selects the size of the sub-picture used in Picture-in-Picture (PIP) mode. LARGE SMALL MIDDLE LARGE PIP POSITION Determines where the PIP appears on the screen. X = 95, Y = 92 ASPECT Selects sub picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See page 17. FULL TEXT TICKER Allow text insertion within main screen with the ability to adjust for direction, position, size, blend for transparency rate, detect and fade in. The TEXT TICKER and PIP functions cannot be used simultaneouslly. If the PIP function is on, it will be deactivated and vice versa if the TEXT TICKER is turned on. OFF SUB INPUT Selects sub picture input signal. PIP RESET Resets PIP options back to factory settings except ASPECT and SUB INPUT. Depend on signal input - OSD LANGUAGE Select the language used by the OSD. ENGLISH ENGLISH (Depend on destination) DEUTSCH FRANÇAIS ITALIANO ESPAÑOL SVENSKA РУССКИЙ OSD TURN OFF Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds. OSD POSITION Determines the location where the OSD appears on the screen. 30 Sec. X = 128, Y = 225 UP DOWN LEFT RIGHT INFORMATION OSD Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range. An interval between 3 to 10 seconds for the Information OSD to appear is available. MONITOR INFORMATION Monitor Information. CARBON SAVINGS: Display the estimated carbon saving information in kg. The carbon footprint factor in the carbon saving calculation is based on the OECD (2008 Edition). English-22 ON, 3 Sec. - Set the transparency level of the OSD. TYPE2 OFF TYPE1 TYPE2 OSD ROTATION Determines the OSD display direction between landscape and portrait. LANDSCAPE Display the OSD with landscape mode. PORTRAIT Display the OSD with portrait mode. LANDSCAPE INPUT NAME You can set currently displayed INPUT name as you like. Max: 8 characters, including Space, A-Z, 0-9, and some symbols. - CLOSED CAPTION Activates closed captioning (for U.S. only). OSD RESET Resets the following settings within the OSD menu back to factory setting: OSD TURN OFF, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY, CLOSED CAPTION. - MONITOR ID Sets the monitor ID number from 1-100 and group ID from A-J. NOTE: Group ID is made of multiple selections. 1 IR CONTROL Selects the mode of the monitor for use with the infra-red remote control when using the RS-232C daisy chain. OFF MULTI DISPLAY NORMAL The monitor will be controlled normally by wireless remote controller. PRIMARY Choose “PRIMARY” for the first monitor within an RS-232C daisy chain. SECONDARY Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain. LOCK Prevents the monitor from being controlled by wireless remote controller. To return to normal operation, press the “DISPLAY” button on the remote controller for 5 seconds. TILE MATRIX NORMAL Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution amplifier. NOTE: Low resolution is not suitable for tiling to a large number of monitors. H MONITORS Number of monitors arranged horizontally. 1 V MONITORS Number of monitors arranged vertically. 1 POSITION Select which section of the tiled image to be displayed on the monitor. 1 TILE COMP Turns the TILE COMP feature on. NO ENABLE Enables Tile Matrix. NO POWER ON DELAY Adjusts the delay time between being in “standby” mode and entering “power on” mode. “POWER ON DELAY” can be set between 0 and 50 seconds. POWER INDICATOR Turns ON or OFF the LED located at the front of the monitor. If “OFF” is selected, LED will not light when the LCD monitor is in active mode. EXTERNAL CONTROL Selects the control interface, RS-232C or LAN. LAN RESET Resets the LAN settings. In daisy chain condition, set the OSD menu categories which copy from current monitor to others. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”. This function reset to default when power off. This function has limit up to about 5 monitors. COPY START Select “YES” and press SET button to start copy. ALL INPUT When you check this item, copy to all input teminals. Default is off. MULTI DISPLAY RESET ON RS-232C CONTROL SETTING COPY 0 Sec. Resets “MULTI DISPLAY” options back to factory settings. English-23 NO - English OSD TRANSPARENCY DISPLAY PROTECTION POWER SAVE All inputs except for TV* Sets how long the monitor waits to go into power save mode after a lost signal. Note: When connecting DVI, video card might not stop sending digital data even if image has disappeared. In this case the monitor does not get to power management mode. STANDBY MODE Lowers power consumption. Note: When ECO STANDBY is selected, DDC/CI does not function. HEAT STATUS Displays status of the FAN, BRIGHTNESS and TEMPERATURE. FAN CONTROL Cooling fan reduces the temperature of the display to protect from overheating. If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed. SCREEN SAVER Use the SCREEN SAVER function to reduce the risk of Image Persistence. ON ECO STANDBY AUTO GAMMA The display gamma is changed and fixed when “ON” is selected. OFF BRIGHTNESS The brightness is decreased when “ON” is selected. NOTE: Do not select this function when picture model is AMBIENT1 or AMBIENT2. OFF MOTION The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined intervals. You can set interval time and zooming ratio. OFF SIDE BORDER COLOR Adjusts the color of the side borders when a 4:3 image is displayed. Press + button, the bar will become lighter. Press - button, the bar will become darker. 15 AUTO BRIGHTNESS DPORT, DVI, VGA, RGB/HV inputs only Adjusts the brightness level according to the input signal. NOTE: Do not select this function when picture model is AMBIENT1 or AMBIENT2. CHANGE SECURITY PASSWORD Allows the security password to be changed. The factory preset password is 0000. SECURITY LOCK Locks the security password. DDC/CI ENABLE/DISABLE: Turns On or OFF the two way communication and control of the monitor. ENABLE DISPLAY PROTECTION RESET Resets the following settings within the DISPLAY PROTECTION menu back to factory setting: POWER SAVE, STANDBY MODE, SCREEN SAVER, SIDE BORDER COLOR, AUTO BRIGHTNESS, DDC/CI. - OFF OFF ADVANCED OPTION INPUT DETECT All inputs except for TV* Selects the method of input detection the monitor uses when more than two input devices are connected. NONE The Monitor will not search the other video input ports. FIRST DETECT When the current video input signal is not present, then the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically. The monitor will not look for other video signals while the current video source is present. LAST DETECT When the monitor is displaying a signal from the current source and a new secondary source is supplied to the monitor, the monitor will automatically switch to the new video source. When current video input signal is not present, the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically. VIDEO DETECT DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO inputs will have priority over DVI, VGA, RGB/HV. When DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO input signal is present the monitor will change and keep to the DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO input. CUSTOM DETECT Set the priority of input signals. When CUSTOM DETECT is selected, monitor searches listed inputs only. INPUT CHANGE Sets input change speed. NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed. This function should be chosen after all adjustment options have been made for the input. LONG CABLE COMP Manually compensates for image degradation caused from using a long cable. EQUALIZE FIRST DETECT NORMAL OFF VGA, RGB/HV inputs only POLE Adjusts frequency. 0 PEAK Adjusts equalizing value. 0 *: The product you purchased may not have this feature. English-24 Adjusts gain value. 0 OFFSET Adjusts slice level of synchronized signal. 0 SYNC TERMINATE Selects the terminate resistance for matching the cable impedance. HIGH RGB/HV inputs only TERMINAL SETTING DVI MODE Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” when PC or other computer equipment is connected. Select “DVI-HD” when DVD player, which has DVI-D output, is connected. BNC MODE Selects the kind of equipment which is connected to the BCN input. RGB: Analog input COMPONENT: Component VIDEO: RGB SCART MODE Input mode for devices using SCART connectors. OFF HDMI SIGNAL RAW/EXPAND SCAN CONVERSION All inputs except VGA, RGB/HV EXPAND Selects the IP (Interlace to Progressive) conversion function. Note: For DVI input “DVI-HD” need to be enabled in the DVI mode menu. PROGRESSIVE Converts interlaced signals to progressive. This is the default setting. INTERLACE Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of image retention. COLOR SYSTEM DVI-PC The selected Color System depends on the video format of the input signal. PROGRESSIVE AUTO VIDEO1, VIDEO2, S-VIDEO inputs only AUTO Automatically chooses Color System setting based on input signal. NTSC PAL SECAM 4.43 NTSC PAL-60 SCAN MODE Some video formats may require different scanning modes in order to best display the image. OVER SCAN HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only OVER SCAN Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the image will be shown on the screen. UNDER SCAN Image size stays within the display area. The whole image is displayed on the screen. ADVANCED OPTION RESET Resets the following settings within the ADVANCED OPTION menu back to factory setting: INPUT DETECT, INPUT CHANGE, LONG CABLE COMP, TERMINAL SETTING, SCAN CONVERSION, COLOR SYSTEM, SCAN MODE. - FACTORY RESET Resets OSD options back to factory settings EXCEPT FOR: DATE & TIME, LANGUAGE, OSD ROTATION, INPUT NAME, CHANGE SECURITY PASSWORD, SECURITY LOCK and SECURITY PASSWORD. - *: The product you purchased may not have this feature. English-25 English GAIN NOTE 1: CREATING A SCHEDULE The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed. To program the schedule: 1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now be programmed. 2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner. 3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight PIC. MODE. Use the + and - buttons to choose the picture mode. 4. Use the down button to select a day on which the schedule will be enabled. Push the set button to enable. If the schedule is to be ran every day, choose EVERY DAY and press the SET button. The circle next to EVERY DAY will turn yellow. If a weekly schedule is desired, choose the days of the week using the up and down buttons and pressing SET to select. Then highlight the EVERY WEEK option and press SET. 5. After a schedule is programmed the remaining schedules can then be set. Press MENU to leave the OSD or press EXIT to go back to the previous menu. DVI SCHEDULE: OFF TIMER SCHEDULE SETTINGS SCHEDULE LIST DATE & TIME SCHEDULE RESET RESET Note: If schedules are overlapping then the schedule with the highest number will have priority over the schedule with the lowest number. For example schedule #7 will have priority over schedule #1. If selected input or picture mode is not available now, disable input or picture mode is shown in red. (THU) JUN.18.2009 15:38 SETTINGS: 1 2 3 ON: OFF: INPUT: PIC. MODE: EVERY DAY EVERY WEEK MON TUE FRI Choose Mark 4 5 6 7 ––:–– ––:–– –––– –––– WED SAT Return THU SUN Close NOTE 2: IMAGE PERSISTENCE Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence. For long life use as Public Display Image Sticking of LCD Panel When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or “ghost” image of previous image may be observed. (Image Persistence) Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along the displayed image, and may be permanent. (Image Sticking) Recommendations To prevent Image Sticking, and for longer life usage of LCD, the following are recommended. 1. Fixed image should not be displayed for long period. Change fixed images after short intervals. 2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions. 3. Lower environmental temperatures prolong the lifespan of the monitor. When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are stacked, utilize the temperature sensors inside monitor. To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness. 4. Please use “Screen Saver Mode” of monitor. English-26 English Remote Control Function REMOTE CONTROL ID FUNCTION Monitor ID:1 Monitor ID:2 Monitor ID:3 Remote works Remote works Remote works REMOTE CONTROL ID The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors. For example: if there are many monitors being used in the same area, a remote control in normal mode would send signals to every monitor at the same time (see Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specific monitor within the group (see Figure 2). TO SET REMOTE CONTROL ID While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then be used to operate the monitor having that specific Monitor ID number. When 0 is selected or when the remote control is in normal mode, all monitors will be operated. TO SET/RESET REMOTE CONTROL MODE ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for 2 seconds. Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold down for 2 seconds. In order for this feature to work properly, the display must be assigned a Monitor ID number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD (See page 23). Figure 1 Remote in Normal mode or the REMOTE ID is set to 0 Monitor ID:1 Monitor ID:2 Monitor ID:3 Remote does not work Remote does not work Remote works Figure 2 Remote set up to use REMOTE ID:3 Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button. The MONITOR ID number is shown on the display when your remote control is in ID mode. Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it. 1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100. This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors. 2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number (1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously control all displays in range. 3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button. The MONITOR ID number is shown in red on the display. If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red. If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same. This LCD monitor can be controlled via personal computer or wireless remote control using an RS-232C connection. MONITOR ID and IR CONTROL Using one PC or one infrared wireless controller, up to 100 individual LCD monitors can be controlled through a daisy chain via RS-232C connection. 1. Connect PC and LCD monitors. Connect a PC’s RS-232C control output to the LCD monitor RS-232C input. You can then connect the RS-232C output from the LCD monitor to another LCD monitor RS-232C input. Up to 100 monitors can be connected using RS-232C. 2. Set Monitor ID and IR Control mode. For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under the “MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two monitors should share the same Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially from 1. The first monitor in the daisy chain is designated as the primary monitor. Subsequent monitors with the chain are secondary monitors. In the “ADVANCED OPTION” menu on the first monitor in the RS-232C daisy chain set the “IR CONTROL” to “PRIMARY”. Set the “IR CONTROL” to “SECONDARY” on all other monitors. English-27 3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at top left side of the screen. Monitor ID: Displays the ID number of the current monitor within the daisy chain. Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor. Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy chained monitors simultaneously, select “ALL” as the “Target ID.” 4. Use the wireless remote controller to control the “SECONDARY” monitor while aiming at the “PRIMARY” monitor. The “MENU OSD” will appear on the selected target monitor. NOTE: If the “ID No.” mode select OSD is showing, press the “DISPLAY” button on the remote control while pointing at the “PRIMARY” monitor to clear this OSD. HINT: If you lost control due to the incorrect setting of “IR CONTROL”, pressing the “DISPLAY” button on the remote control for 5 or more seconds will reset the “IR CONTROL” menu to “NORMAL” function. WIRED REMOTE CONTROL FUNCTION You can control this monitor by connecting REMOTE IN/OUT with Stereo Mini plug cable (3.5 MultiSync Remote IN IN ). MultiSync Remote OUT Remote IN Remote OUT OUT MultiSync Remote control cable NOTE: Remote control cable Turn off the main power switch before connect/disconnect Stereo Mini plug cable. English-28 This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23). Functions that can be controlled by a personal computer are: • Power ON or OFF • Switching between input signals Connection LCD Monitor + PC PC (Out) IN MultiSync OUT RS-232C (IN) MultiSync RS-232C (OUT) RS-232C Cable RS-232C (IN) RS-232C (OUT) RS-232C Cable MultiSync NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details. * In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model. Do not connect to other types of equipment. To control monitor or multiple monitors that are daisy-chained together please use the control command. Instructions for the control command can be found on the CD included with the display. The file is called “External_control.pdf”. 1) Interface PROTOCOL RS-232C BAUD RATE 9600 [bps] DATA LENGTH 8 [bits] PARITY BIT NONE STOP BIT 1 [bit] FLOW CONTROL NONE This LCD monitor uses RXD, TXD and GND lines for RS-232C control. 2) Control command diagram Please see file “External_Control.pdf” on the CD-ROM. English-29 English Controlling the LCD monitor via RS-232C Remote Control Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23). To use a LAN connection, you are required to assign an IP address. Example of LAN connection: Server NOTE: Use a category 5 or higher LAN cable. Hub LAN cable (not supplied) Network Setting by Using an HTTP Browser Overview Connecting the monitor to a network allows for monitor control from a computer via the network. To perform the monitor control from a web browser, you must have an exclusive application installed on your computer. The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will vary depending on the version of browser. Please refer to the help files and the other information provided in your software.) Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the monitor and entering the following URL. Network Setting http://<the Monitor’s IP address>/index.html TIP: The default IP address is “192.168.0.10”. NOTE: If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to refresh your web browser (or clear the cache). The display or button’s response can be slowed down or operation may not be accepted depending the settings of your network. Should this happen, consult your network administrator. The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and repeat. If you still can’t get a response, turn off and back on the monitor. English-30 Connect the monitor to a commercially available LAN cable before engaging in browser operations. Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation. It is recommended that a proxy server not be used unless it is unavailable. Handling of the Address for Operation via a Browser Regarding the actual address that is entered for the address or entered into the URL column when operation of the monitor is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the monitor has been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of the monitor has been set in the “HOSTS” file of the computer being used. Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL. Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying http://192.168.73.1/index.html for the address or the entry column of the URL. Network Settings http://<the Monitor’s IP address> /index.html DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server. Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator. NOTE: The IP address of the monitor is required to change the network setting. The IP address will not be displayed on the Monitor’s menu. Consult your network administrator for the IP address when [ENABLE] is selected for [DHCP]. IP ADDRESS Set your IP address of the network connected to the monitor when [DISABLE] is selected for [DHCP]. SUBNET MASK Set your subnet mask number of the network connected to the monitor when [DISABLE] is selected for [DHCP]. DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when [DISABLE] is selected for [DHCP]. DNS (PRIMARY) Set your primary DNS settings of the network connected to the monitor. DNS (SECONDARY) Set your secondary DNS settings of the network connected to the monitor. UPDATE Reflect your settings. NOTE: Close the browser after clicking [UPDATE]. The monitor will automatically update your settings. English-31 English Preparation Before Use Alert Mail Setting http://<the Monitor’s IP address>/lanconfig.html This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when an error occurs in the monitor. HOST NAME Type in the hostname of the network connected to the monitor. Up to 60 alphanumeric characters can be used. DOMAIN NAME Type in the domain name of the network connected to the monitor. Up to 60 alphanumeric characters can be used. ALERT MAIL Checking [ENABLE] will turn on the Alert Mail feature. Checking [DISABLE] will turn off the Alert Mail feature. SENDER’S ADDRESS Type in the senders address. Up to 60 alphanumeric and symbols characters can be used. SMTP SERVER NAME Type in the SMTP server name to be connected to the monitor. Up to 60 alphanumeric characters can be used. RECIPIENT’S ADDRESS 1 to 3 Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used. APPLY Click this button to reflect the above settings. EXECUTE Click this button to send a test mail to check if your settings are correct. STATUS A reply to a test mail will be displayed. NOTE: • If you execute a test, you may not receive an Alert mail. Should this happen, check if the network settings are correct. • If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient’s Address is correct. TIP: The Alert Mail settings will not be affected even when [RESET] is done from the menu. For Control command diagram, please see file “External_Control.pdf” on the CD-ROM. English-32 Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the same as on the color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen and customise the color accuracy of your monitor to a variety of standards. sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and backward compatibility with other common color standards. OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus. Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically optimizing display performance. IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the air conditioning costs of the workplace. FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. VESA Standard (FDMIv1) Mounting Interface: Allows users to connect their LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America. DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital connectors such as DFP and P&D. The DVI interface of this display supports HDCP. TILE MATRIX, TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width. ZOOM: Expands image size for horizontal and vertical direction. RS-232C daisy chain: You can control the multiple monitors by controller or wireless remote controller. Self-diagnosis: If an internal error should occur, a failure state will be indicated. Long cable capability: Automatic long cable compensation prevents image quality degradation (dull signals) caused by long cable lengths. English-33 English Features Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and recommended settings. • Check the signal cable connector for bent or pushed-in pins. Power Button does not respond • Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor. Image persistence • Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. RED LED on monitor is blinking • A certain failure might have occurred, please contact your nearest authorized NEC DISPLAY SOLUTIONS service facility. • If the monitor is powered off by the inside temperature being higher than the normal operating temperature, a RED LED will blink six times. Power on the display again after confirming the inside temperature has been reduced to normal operation temperature. Display image is not sized properly • Use the OSD Image Adjust controls to increase or decrease the coarse adjustment. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) Selected resolution is not displayed properly • Use OSD Display Mode to enter Information menu and confirm that the appropriate resolution has been selected. If not, select corresponding option. No Sound • Check to see if audio cable is properly connected. • Check to see if mute is activated. • Check to see if volume is set at minimum. • Check to see if computer supports an audio signal through DisplayPort. If unsure, contact the computer manufacturer. Remote Control is not available • Check the Remote Control’s batteries status. • Check if batteries are inserted correctly. • Check if the Remote Control is pointing at the monitor’s remote sensor. • Check the Remote Control Mode status. • The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor, or when there is an object in the path. Image is unstable, unfocused or swimming is apparent • Signal cable should be completely attached to the computer. • Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment. When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted. “SCHEDULE”/“OFF TIMER” function is not working properly • The “SCHEDULE” function will be disabled when the “OFF TIMER” is set. • Check the monitor and your display card with respect to compatibility and recommended signal timings. • • If your text is garbled, change the video mode to noninterlace and use 60Hz refresh rate. Image of component signal is greenish • Check to see if the DVD/HD input connector is selected. LED on monitor is not lit (no green or red color can be seen) • Power Switch should be in the ON position and power cord should be connected. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). If the “OFF TIMER” function is enabled and the power to the LCD monitor is turned off when the power supply is interrupted unexpectedly, then the “OFF TIMER” will be reset. Snowy Picture, Poor Sound in TV • Check antenna/cable connection. Use new cable if necessary. Interference in TV • Check components for shielding, move away from monitor if necessary. RS-232C or LAN control is not available • Check RS-232C or LAN cable connection. • Check “CONTROL” setting in “EXTERNAL CONTROL”. Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or degradation. English-34 English Specifications - P401 Product Specifications LCD Module Pixel Pitch: Resolution: Color: Brightness: Contrast Ratio: Viewing Angle: Design View Distance: Frequency Horizontal: Vertical: 40" /101.6 cm diagonal 0.461 mm 1920 x 1080 Over 16 million colors (depending on video card used) 650 cd/m2 (Max.), 500 cd/m2 (Typ.) @25°C 3000:1 89° (typ) @ CR>10 1100 mm 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input) 50.0 - 85.0 Hz Pixel Clock 25.2 MHz - 162.0 MHz Viewable Size 885.6 x 498.2 mm Input Signal DVI Digital RGB DVI (HDCP) VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz) DisplayPort DisplayPort Connector Digital RGB DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3 VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz) VGA Analog RGB 0.7 Vp-p/75 ohm VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz) Sync Separate: TTL level (Pos./Neg.) Composite sync on Green Video: 0.3 Vp-p Neg. Analog RGB 0.7 Vp-p/75 ohm VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz) Sync Separate: TTL level (Pos./Neg.) Composite sync on Green Video: 0.3 Vp-p Neg. RGB/HV DVI-D 24pin 15pin Mini D-sub BNC (R,G,B,H,V) HDMI HDMI Connector Digital RGB HDMI 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz DVD/HD1 DVD/HD2 RCA (Y, Cb/Pb, Cr/Pr) BNC Component Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz VIDEO1 VIDEO2 BNC/RCA BNC Composite 1.0 Vp-p/75 ohm NTSC/PAL/SECAM/4.43NTSC/PAL60 S-VIDEO Mini DIN 4 pin S-VIDEO Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM) NTSC/PAL/SECAM/4.43NTSC/PAL60 RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p with 75 ohm terminated Separate HV sync: TTL level (Posi / Nega) DVD/HD2 BNC Output Signal Component Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm Composite 1.0 Vp-p with 75 ohm terminated RCA (L/R) X2 STEREO Mini Jack Analog Audio Stereo L/R 0.5 Vrms HDMI Connector VIDEO1/VIDEO2 BNC AUDIO AUDIO Input AUDIO Output Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit) DisplayPort Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit) RCA (L/R) Stereo L/R 0.5 Vrms Analog Audio Speaker Output External Speaker Jack 15 W + 15 W (8 ohm) Control TV*2 RS-232C In: RS-232C Out: LAN: Remote IN: Remote OUT: Antenna: Channel Coverage: Power Supply 9 Pin D-sub 9 Pin D-sub (with daisy chain) RJ-45 10/100 BASE-T Stereo Mini jack 3.5 Stereo Mini jack 3.5 F-connector Impedance 75 ohm VHF: 2 - 13 ch UHF: 14 - 69 ch CATV: 1 - 130 ch ATSC (8VSB): 2 - 69 ch 64/256 QAM : 1 - 135 ch 3.5 - 1.45 A @ 100-240VAC, 50/60Hz Operational Environment Temperature: Humidity: Altitude: 5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness) 20 - 80% (without condensation) 0 - 3000 m (Brightness may decrease with altitude) Storage Environment Temperature: Humidity: -20 - 60°C / -4 - 140°F 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C Dimension 919.7 (W) x 532.2 (H) x 140.0 (D) mm / 36.2 (W) x 21.0 (H) x 5.5 (D) inches Weight 24.0 Kg (52.9 lbs) VESA compatible arm mounting interface 300 mm x 300 mm (M6, 4 Holes) Complied Regulatory and Guidelines UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1 FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R Power Management VESA DPM Plug & Play VESA DDC2B, DDC/CI, DisplayPort Accessories Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 3, Screw x 9, CD-ROM, Thumbscrew for optional stand x 2, Cable cover NOTE: Technical specifications are subject to change without notice. *1: Compressed image English-35 *2: The product you purchased may not have this feature. Specifications - P461 Product Specifications LCD Module Pixel Pitch: Resolution: Color: Brightness: Contrast Ratio: Viewing Angle: Design View Distance: Frequency Horizontal: Vertical: 46" /116.8 cm diagonal 0.530 mm 1920 x 1080 Over 16 million colors (depending on video card used) 650 cd/m2 (Max.), 500 cd/m2 (Typ.) @25°C 4000:1 89° (typ) @ CR>10 1300 mm 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input) 50.0 - 85.0 Hz Pixel Clock 25.2 MHz - 162.0 MHz Viewable Size 1018.1 x 572.7 mm Input Signal DVI Digital RGB DVI (HDCP) VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz) DisplayPort DisplayPort Connector Digital RGB DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3 VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz) VGA Analog RGB 0.7 Vp-p/75 ohm VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz) Sync Separate: TTL level (Pos./Neg.) Composite sync on Green Video: 0.3 Vp-p Neg. Analog RGB 0.7 Vp-p/75 ohm VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz) Sync Separate: TTL level (Pos./Neg.) Composite sync on Green Video: 0.3 Vp-p Neg. RGB/HV DVI-D 24pin 15pin Mini D-sub BNC (R,G,B,H,V) HDMI HDMI Connector Digital RGB HDMI 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz DVD/HD1 DVD/HD2 RCA (Y, Cb/Pb, Cr/Pr) BNC Component Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz VIDEO1 VIDEO2 BNC/RCA BNC Composite 1.0 Vp-p/75 ohm NTSC/PAL/SECAM/4.43NTSC/PAL60 S-VIDEO Mini DIN 4 pin S-VIDEO Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM) NTSC/PAL/SECAM/4.43NTSC/PAL60 RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p with 75 ohm terminated Separate HV sync: TTL level (Posi / Nega) DVD/HD2 BNC Output Signal Component Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm Composite 1.0 Vp-p with 75 ohm terminated RCA (L/R) X2 STEREO Mini Jack Analog Audio Stereo L/R 0.5 Vrms HDMI Connector VIDEO1/VIDEO2 BNC AUDIO AUDIO Input AUDIO Output Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit) DisplayPort Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit) RCA (L/R) Stereo L/R 0.5 Vrms Analog Audio Speaker Output External Speaker Jack 15 W + 15 W (8 ohm) Control TV*2 RS-232C In: RS-232C Out: LAN: Remote IN: Remote OUT: Antenna: Channel Coverage: Power Supply 9 Pin D-sub 9 Pin D-sub (with daisy chain) RJ-45 10/100 BASE-T Stereo Mini jack 3.5 Stereo Mini jack 3.5 F-connector Impedance 75 ohm VHF: 2 - 13 ch UHF: 14 - 69 ch CATV: 1 - 130 ch ATSC (8VSB): 2 - 69 ch 64/256 QAM : 1 - 135 ch 3.9 - 1.6 A @ 100-240VAC, 50/60Hz Operational Environment Temperature: Humidity: Altitude: 5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness) 20 - 80% (without condensation) 0 - 3000 m (Brightness may decrease with altitude) Storage Environment Temperature: Humidity: -20 - 60°C / -4 - 140°F 10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C Dimension 1055.4 (W) x 608.6 (H) x 140.0 (D) mm / 41.6 (W) x 24.0 (H) x 5.5 (D) inches Weight 29.0 Kg (63.9 lbs) VESA compatible arm mounting interface 300 mm x 300 mm (M6, 4 Holes) Complied Regulatory and Guidelines UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1 FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R Power Management VESA DPM Plug & Play VESA DDC2B, DDC/CI, DisplayPort Accessories Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 3, Screw x 9, CD-ROM, Thumbscrew for optional stand x 2, Cable cover NOTE: Technical specifications are subject to change without notice. *1: Compressed image English-36 *2: The product you purchased may not have this feature. English Pin Assignment 1) RS-232C input/output Pin No Name 1 connected to 7&8 2 RXD 3 TXD 4 connected to 6 5 GND 6 connected to 4 7 connected to 1&8 8 connected to 1&7 9 NC D-SUB 9P 5 1 6 This LCD monitor uses RXD, TXD and GND lines for RS-232C control. 2) REMOTE IN 3) REMOTE OUT English-37 9 Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life. All required information concerning the disposal of the product and country-specific information on recycling facilities can be found on our following websites: http://www.nec-display-solutions.com/greencompany/ (in Europe), http://www.nec-display.com (in Japan) or http://www.necdisplay.com (in USA). Energy Saving This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS) Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode. Mode Power consumption LED colour Normal Operation Approx. 175 W (P401) Approx. 210 W (P461) Green Energy Saving Mode Less than 2 W Amber Blinking Power Off (STANDBY) Less than 1 W Amber Power Off (Eco standby) Less than 0.5 W Red WEEE Mark (European Directive 2002/96/EC) Within the European Union EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself and NEC. The mark on electrical and electronic products only applies to the current European Union Member States. Outside the European Union If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method. English-38 ">
/
Download
Just a friendly reminder. You can view the document right here. But most importantly, our AI has already read it. It can explain complex things in simple terms, answer your questions in any language, and help you quickly navigate even the longest or most compilcated documents.
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Multiple Input Options (HDMI, DVI, DisplayPort, VGA)
Wireless Remote Control
Adjustable Picture Settings
Power Management Features
Multi-Display Support
RS-232C and LAN Control
Frequently asked questions
Use the INPUT button on the control panel or remote control to cycle through available inputs (DVI, DisplayPort, VGA, HDMI, etc.).
Use the OSD (On-Screen Display) controls accessible via the control panel or remote control.
The monitor provides power-saving modes and a schedule setting to optimize energy consumption.
Yes, the monitor supports multi-display configurations and offers RS-232C and LAN control for managing multiple units.
