NEC IVS2 User's Manual

NDA-24273
ISSUE 1
STOCK # 152009
®
ISDN Features and Specifications
APRIL, 2000
NEC America, Inc.
LIABILITY DISCLAIMER
NEC America, Inc. reserves the right to change the specifications,
functions, or features, at any time, without notice.
NEC America, Inc. has prepared this document for use by its
employees and customers. The information contained herein is
the property of NEC America, Inc. and shall not be reproduced
without prior written approval from NEC America, Inc.
NEAX and Dterm are registered trademarks of NEC Corporation.
Copyright 2000
NEC America, Inc.
Printed in U.S.A.
ISSUE No.
ISSUE No.
PAGE No.
PAGE No.
1
i
1
ii
1
iii
1
iv
1
v
1
vi
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
1
10
1
11
1
12
1
13
1
14
1
15
1
16
1
17
1
18
1
19
1
20
1
2
3
4
ISSUE 1
DATE
APRIL, 2000
6
7
8
1
ISSUE 2
DATE
ISSUE 5
DATE
5
3
4
ISSUE 3
DATE
ISSUE 6
DATE
2
6
7
8
ISSUE 4
DATE
ISSUE 7
DATE
5
ISSUE 8
DATE
IVS2
NEAX2000
ISDN Features and Specifications
Revision Sheet 1/1
NDA-24273
NEAX2000 IVS2
ISDN Features and Specifications
TABLE OF CONTENTS
Page
BUSINESS FEATURE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SUPPORTED NETWORK SERVICES (TRUNK PRE-PROVISIONED ONLY) . . . . . . . . . . . . . . . . . . . . iii
ISDN NETWORK REQUIREMENTS FOR LAYER ONE (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
TABLE OF FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
CALL-BY-CALL SERVICE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT)) . . . . . . . . . . . . . . . . . 2
CPN TO NETWORK–PRESENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CPN TO TERMINATING USER–DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DID ADDRESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DID AND DOD ADDRESSING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
EVENT BASED CCIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ISDN TERMINAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MEGACOM ® ACCESS/WATS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MEGACOM ® 800 SERVICE/800 WATS ULTRA WATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MULTIQUEST®/900 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SUBADDRESS–PRESENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TRUNK PROVISIONING SERVICE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
APPENDIX A: Dterm FIXED FUNCTION KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
APPENDIX B: Dterm LCD DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
FEBRUARY, 2000
Page i
BUSINESS FEATURE LIST
Account code
Answer Key
Attendant Delay Announcement
Attendant Overflow
Authorization Code
Automated Attendant
Broker’s Call
Call Forwarding
Call Forwarding - All Calls
Call Forwarding - Busy Line
Call Forwarding - No Answer
Call Forwarding - Outside
Multiple Call Forwarding - All
Multiple Call Forwarding - Busy
Multiple Call Forwarding - No Answer
Split Call Forwarding - Busy Line
Call Forwarding - Override
Group Division
Call Park - System
Call Pickup - Direct
Call Pickup - Group
Class of Service
Code Restriction
Conference
Consecutive Speed Dial
Consultation Hold
Delayed Ringing
Direct Inward Termination(DID)
DID Call Waiting
DID Digit Conversion
Direct Inward System Access(DISA)
Direct Inward Termination(DIT)
Distinctive Ringing
Do Not Disturb
Elapse Call Timer
Forced Account Code
Group Listening
Hold - Call
Hold - Exclusive
Hold - Nonexclusive
Last Number Redial
Least Cost Routing 3/6 Digit
Page ii
Maintenance Administration Terminal (MAT)
Fault Messages
Peg Count
Night Service
Call Rerouting
Day/Night Mode Change - ATTCON
Day/Night Mode Change - Station
Night Connection - Fixed
Night Connection - Flexible
Trunk Answer from Any Station (TAS)
Route Advance
Save and Repeat
Stack Dialing
Station Hunting - Circular
Station Hunting - Terminal
Station Hunting - Secretarial
Station Message Detail Recording (SMDR)
Station Speed Dialing
System Speed Dialing
Tenant Service
Trunk Queueing - Outgoing
Trunk to Trunk Connection
Uniform Call Distribution (UCD)
"Silent Monitor"
Voice Mail Integration
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
SUPPORTED NETWORK SERVICES
(TRUNK PRE-PROVISIONED ONLY)
AT&T
• Software Defined Network
• Global Software Defined Network
• International 800 Service
• International MEGACOM®
Also, AT&T’s Alternate Destination Call Redirection fearure is supported by the NEAX2000 IVS2.
NT
• Incoming
-Private
-Tie
-WATS
-800WATS
Note
• Outgoing
-DID/DOD
Note
Note: Services that do not require NSF can be supported by the NEAX2000 IVS2.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page iii
ISDN NETWORK REQUIREMENTS FOR LAYER ONE (1)
• Interface:
T1(1.544 M) only
• Framing:
ESF (24 Multiframe)
only
• Line Coding:
B8ZS only
• D Channel Rate:
64K only
• D Channel:
T1 Channel Number 24
(24th channel).
Individual B channels cannot be looped back,
local or remote.
Page iv
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
TABLE OF FEATURES
X = available
FEATURE
→ = carried over to next level software
1900
2000
CALL-BY-CALL SERVICE SELECTION
X
→
CALLED PARTY RECOGNITION SERVICE
(DIRECT-IN TERMINATION (DIT))
X
→
CPN TO NETWORK—PRESENT
X
→
CPN TO TERMINATING USER—DISPLAY
X
→
DID ADDRESSING
X
→
DID AND DOD ADDRESSING
X
→
EVENT BASED CCIS
X
→
ISDN TERMINAL
X
→
MEGACOM ® ACCESS/WATS
X
→
MEGACOM ® 800 SERVICE/800 WATS/ULTRA WATS
X
→
MULTIQUEST®/900 SERVICE
X
→
SUB-ADDRESS—PRESENT
X
→
TRUNK PROVISIONING SERVICE SELECTION
X
→
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page v
This page is for your notes.
Page vi
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
CALL-BY-CALL SERVICE SELECTION
CALL-BY-CALL SERVICE SELECTION
General Description
Services can be selected on a call-by-call basis to all channels of a single PRI interface according to applications.
That is, unlike Trunk Provisioning Service in which services are assigned to specific channels, services may be
used on any available channel.
Operating Procedure
No manual operation is required.
Service Conditions
1. The services that can be designated include ACCUNET, MEGACOM, MEGACOM 800,
INTERNATIONAL 800, SDN, MULTIQUEST (AT&T), and PRIVATE, INWATS, OUTWATS, FX, TIE
(Northern Telecom).
2. Channel selection is possible by the LCR function only.
Note:
During call temination, there is no indication of which service is being used.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 1
CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT))
CALLED PARTY RECOGNITION SERVICE
(DIRECT-IN TERMINATION (DIT))
General Description
This feature provides an incoming Direct-In Termination (DIT) call via an ISDN trunk to be connected to a predetermined station. This application can be used for a station or modem.
Operating Procedure
No manual operation is required.
Station Application
All stations.
Service Conditions
1. For incoming calls in a Primary Rate Interface trunk, this service feature should be used only when DID
trunks are not desired.
2. Refer to the Business Features and Specifications manual for details on service conditions.
Page 2
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
CPN TO NETWORK–PRESENT
CPN TO NETWORK–PRESENT
General Description
This feature allows the ISDN network to be informed of the Calling Party Number (CPN) when a call originates
from a terminal connected to the System.
DIAL "516-555-4210#"
For this example, the CPN sent to the network may be
214-555-5000 for every station in the PBX, or each
station may present a unique extension number (last
four digits) to the ISDN network.
PBX
DTI
(214-555-5000)
ISDN
4210
Called Party No.
(214-555-5001)
516-555-4210
+214-555-5000
(214-555-5002)
Calling Party No.
Calling Party No.
DTI: Digital Trunk Interface
Operating Procedure
No manual operation is required. The calling station number is sent to the ISDN network automatically.
Service Conditions
1. The data provided as the calling station number is assigned via MAT/CAT for each ISDN circuit or station.
In addition, if no data has been assigned as the calling station number, the system will not provide any
information to the network.
2. A maximum of 16 digits can be assigned as the calling station number.
3. The maximum number of area codes and office code patterns is 15.
4. Transmission of CPN to the ISDN network can be programmed by the Class of Service. Programming is
required for each station.
5. The delivery of CPN information is subject to local regulations.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 3
CPN TO TERMINATING USER–DISPLAY
CPN TO TERMINATING USER–DISPLAY
General Description
This feature provides a visual display of the originating station’s number and subaddress information on a
Multiline Terminal for incoming ISDN calls. This provides the terminal user with a quick and accurate way to
identify the originating station’s number (Calling Number).
Operating Procedure
No manual operation is required. The originating station number is automatically displayed on the Multiline
Terminal.
Service Conditions
1. This feature is available on the Multiline Terminal with Display.
2. A maximum of 16 digits forming the originating party’s number, including the PBX access code, can be
displayed. For subaddress, a maximum of eight digits can be displayed. If the subaddress exceeds eight
digits, the first eight are displayed. Below is an example of the display when the originating party’s number
is 214-555-5000, and the subaddress is 82623667:
(Elapsed time)
8 2 6 2 3 6 6 7 subaddress
2 1 4 5 5 5 5 0 0 0 calling party number
3. The CPN will be displayed for six seconds only, followed by date and time.
Page 4
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
DID ADDRESSING
DID ADDRESSING
General Description
This feature allows incoming ISDN-PRI calls to terminate to stations, ATTCON, Automated Attendant, etc.,
based on the Called Party number. Direct Inward Dial trunks will be terminated to preprogrammed destinations
without Attendant assistance.
Operating Procedure
No manual operation is required.
Station Application
Not applicable.
Service Conditions
1. If the network is notified that the destination station for the DID call is busy or a connection-controlled
station, the network gives the calling station a Busy Tone. (This depends upon call forwarding services
being in service.)
2. If the called station is nonexistent, the DID call can be routed to the Attendant Console, another
predesignated station, or to receive Reorder Tone.
3. Refer to the Business Features and Specifications manual for more details of DID service.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 5
DID AND DOD ADDRESSING
DID AND DOD ADDRESSING
General Description
This feature allows the system to use DID and DOD on the same B channels. Trunk Provisioning Service
Selection is not required. (B-channels can be used for DID and DOD without separating the trunk routes.)
B-channels
PRI
D-channel
Operating Procedure
No manual operation is required.
Service Conditions
1. Confirm the DID and DOD selection with the customer’s local exchange carrier prior to installation.
2. For more details, refer to “Direct Inward Dialing” and “Direct Outward Dialing” in the Business Features
and Specifications manual.
3. The DID/DOD is supported without service provisioning, since no facility indication to the network is
required.
Page 6
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
EVENT BASED CCIS
EVENT BASED CCIS
General Description
This feature allows a PBX customer that does not have a tie line (or when a customer can not use the tie line due
to the busy or fault of the line), to use the various CCIS feature by using the ISDN line as a CCIS virtual tie line,
on the 2400 IMX - NEAX2000 IVS2 connection or the NEAX2000 IVS2 - NEAX2000 IVS2 connection.
Operating Procedure
No manual operation is required.
Service Conditions
1. Event Based CCIS is available between NEAX2000 IVS 2 to 2400ICS or NEAX2000 IVS 2 to NEAX2000
IVS2.
2. The maximum number of virtual tie lines are 16 channels per system. This includes the common signaling
channels and voice channels.
3. The ISDN line used for the virtual tie line can also be used as a regular ISDN line.
4. This feature supports voice calls only. (Supported object at PBX transmission side: Single Line Telephone,
Multiline Terminal, DID/E&M/Ring Down [analog/T1] tandem calls.)
The data calls are transmitted via the regular ISDN network.
5. The Peg Count (the number of originating call from the ISDN trunk) is counted when using the ISDN line
for the virtual tie line by route basis.
6. Billing information of the virtual tie line using the ISDN line is treated as regular tie line calls.
7. Billing information of the virtual tie line using the ISDN line is treated on tandem calls.
8. The voice channel of the virtual tie line is released at a programmable time after the call finishes.
9. The Common Channel Handler (CCH) card is required for providing Event Based CCIS.
10. The availability of CCIS service features for Event Based CCIS are listed in the following table.
11. For Event Based CCIS using PRI, the following services must be ordered from Telco on the PRI Span:
a. Each B channel must be capable of making and receiving 64K voice calls.
b. Each B channel must be capable of making and receiving 64k Unrestricted Digital Data calls.
c. The ISDN PRI span must be ordered with ISDN Indial (DID) service.
12. The PRI trunks should be ordered with the following components included:
a. Protocol must be National ISDN-1
b. Calling and Called Party Sub-Address
c. NIUF Capability Package S
d. Two B-channels capable of Voice and Data simultaneously on both B-channels
e. Two Directory numbers, each with a SPID
13. For any feature that requires a tandem connection (Call-Forward CCIS, etc.), additional Telco BRI circuits
are required. More than one BRI trunk is required to allow calls to go back to the PBX that transferred or
forwarded a call.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 7
EVENT BASED CCIS
Table 1 CCIS Features Available with Event Based CCIS
SERVICE FEATURE
AVAILABILITY
Attendant Camp-On with Tone Indication-CCIS
X
Attendant Controlled Conference-CCIS
X
Brokerage-Hot-Line-CCIS
X
Busy Verification-CCIS
X
Call Back-CCIS
X
Call Forwarding-All Calls-CCIS
X
Call Forwarding-Busy Line-CCIS
X
Call Forwarding-Don’t Answer-CCIS
X
Call Forwarding-Intercept-CCIS
X
Call Forwarding-Override-CCIS
X
Calling Name Display-CCIS
X
Calling Number Display-CCIS
X
Call Transfer-All Calls-CCIS
X
Centralized Billing-CCIS
X
Centralized Day/Night Mode Change-CCIS
–
Consultation Hold-All Calls-CCIS
X
Deluxe Traveling Class Mark-CCIS
X
Dial Access to Attendant-CCIS
X
Direct-in Termination-CCIS
X
Distinctive Ringing-CCIS
X
Do Not Disturb-CCIS
X
Dual Hold-CCIS
X
Elapsed Time Display-CCIS
X
Flexible Numbering of Station-CCIS
X
Hand-Free-Answer Back-CCIS
X
House-Phone-CCIS
X
Hot Line-CCIS
X
Incoming Call Identification-CCIS
X
Individual Attendant Access-CCIS
X
LDN Night Connection-CCIS
X
Link Alarm Display-CCIS
–
Message Waiting Lamp Setting-Attendant-CCIS
X
REMARKS
Note 4
Note 2
Note 5
Note 3
LEGEND
x : Available
– : Not Available
Page 8
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
EVENT BASED CCIS
Table 1 CCIS Features Available with Event Based CCIS
SERVICE FEATURE
AVAILABILITY
Message Waiting Lamp Setting-Station-CCIS
X
Miscellaneous Trunk Access-CCIS
X
Miscellaneous Trunk Restriction-CCIS
X
Multiple Call Forwarding-All Calls-CCIS
X
Multiple Call Forwarding-Busy Line-CCIS
X
Multiple Call Forwarding-Don’t Answer-CCIS
X
Night Connection Fixed-CCIS
X
Night Connection Flexible-CCIS
X
Outgoing Trunk Queuing-CCIS
–
Paging Access-CCIS
X
Restriction from Outgoing Calls-CCIS
X
Single Digit Station Calling-CCIS
X
Station Controlled Conference-CCIS
X
Station to Station Calling-CCIS
X
Station to Station Calling-Operator Assistance-CCIS
X
Toll Restriction-3/6 Digit-CCIS
X
Trunk Answer from Any Station-CCIS
X
Trunk to Trunk Restriction-CCIS
X
Uniformed Numbering Plan-CCIS
X
Voice Call-CCIS
X
Voice Mail Integration-CCIS
X
REMARKS
Note 3
Note 4
LEGEND
x : Available
– : Not Available
Note 1:
The voice channel and the common signaling channel stay connected after the calls finish according to
the release timer data. Therefore, while the CCIS link is active, the features are available.
Note 2:
The billing information is sent while the CCH link is active. If the sending of billing information fails, it
is sent again when a new CCH link is established by next call.
Note 3:
As a remote office, this feature is available on NEAX2000 IVS2.
Note 4:
An extension of the NEAX2000 IVS2 cannot be a conference leader.
Note 5:
This service is available when the Attendant Console is provided at a 2400 IMX office on the network.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 9
ISDN TERMINAL
ISDN TERMINAL
General Description
This feature provides the system with an ISDN Terminal or Terminal Adapter (TA). ISDN Terminal to ISDN
Terminal, ISDN Terminal to ISDN Trunk, ISDN Trunk to ISDN Terminal, ISDN Terminal to Single Line
Telephone, ISDN Terminal to Multiline Terminal, and ISDN Terminal to PS connections are available.
Operating Procedure
No manual operation is required.
Service Conditions
1. The ISDN Line Circuit (ILC) card and the ISDN Channel handler (ICH) card are required.
2. The ISDN Terminal must be locally powered.
3. The following connections are available:
• Point to Point connection
• Point to Multipoint connection
• National ISDN 1
4. The following features are available:
• Individual Terminal Calling (Point to Multipoint connection)
• Group Calling (Point to Multipoint connection)
• Called Party Recognition Service (DIT)
• DID Addressing
• DID and DOD Addressing
• CPN to Network-Present
• CPN to Terminating User-Display
• Sub Address-Present
• Direct Outward Dialing (DOD)
• Restriction from outgoing call
• Toll restriction
• Station to Station Calling
• Station Hunting
• Simultaneous voice and data transmission
• Asynchronous Data Switching
• Synchronous Data Switching
• Half/Full Duplex Switchover
5. The ISDN Terminal can provide Voice and data communication via the CCIS network. The CCIS network
must be digital.
Page 10
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
ISDN TERMINAL
6. During communication via the CCIS network, the link reconnection is not available.
7. The conditions about station services are as follows:
• Station Hunting
When a Single Line Telephone/Multiline Terminal or an ISDN Terminal calls a busy Single Line
Telephone/Multiline Terminal, another Single Line Telephone/Multiline Terminal in Station Hunting
group is called.
When a Single Line Telephone/Multiline Terminal or an ISDN Terminal calls a busy ISDN Terminal,
another ISDN Terminal in Station Hunting group is called.
Note:
An ISDN Terminal cannot be included in the same Station Hunting group as Single Line Telephone/
Multiline Terminals.
•
8.
9.
10.
11.
Call Forwarding
An ISDN Terminal cannot set Call Forwarding - All Calls/- Busy Line/-Don’t Answer, and cannot be
the destination of a Call Forwarding.
When an ISDN Terminal is a calling station, it can be forwarded to another Single Line Telephone/
Multiline Terminal but cannot be forwarded to central office trunk or tie line trunk.
• Call Transfer
A Single Line Telephone/Multiline Terminal cannot transfer a call in progress with an ISDN Terminal
to another station.
In the same way, an ISDN Terminal cannot transfer a call in progress with a Single Line Telephone/
Multiline Terminal to another station.
While a Single Line Telephone/Multiline Terminal converses with CCIS trunk and ISDN trunk, the
Single Line Telephone/Multiline Terminal cannot transfer the call to an ISDN Terminal.
• Call Pickup, Call Pickup - Designated group
An ISDN Terminal cannot be assigned to Call Pickup group and cannot pickup a call to another station.
A Single Line Telephone/Multiline Terminal cannot pickup a call to an ISDN Terminal.
• Executive Override
During voice communication between a Single Line Telephone/Multiline Terminal and an ISDN
Terminal, another Single Line Telephone/Multiline Terminal can interrupt into only Single Line
Telephone/Multiline Terminal. During data communication with an ISDN Terminal, Executive
Override is not allowed.
• Busy Service (Step Call, Call Back)
When a Single Line Telephone/Multiline Terminal calls a busy ISDN Terminal, busy service such as
Step Call and Call Back cannot be provided to the ISDN Terminal.
It is the same when an ISDN Terminal calls a busy Single Line Telephone/Multiline Terminal.
When a Single Line Telephone is calling an ISDN Terminal or an ISDN Terminal is busy, hooking service
is not available. Therefore, at this time other services are not available.
A Multiline Terminal can call an ISDN Terminal via Primary Extension or Sub Line. And a Multiline
Terminal can be called from an ISDN Terminal via Primary Extension or Sub Line.
When a Single Line Telephone/Multiline Terminal calls an ISDN Terminal, it can send the calling station
number to the ISDN Terminal. At this time, ISDN trunk number and local number are also attached to be
sent.
Station to Station Calling between an attendant console and an ISDN Terminal is not available.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 11
ISDN TERMINAL
12. In case of Point to Multipoint connection, a Single Line Telephone/Multiline Terminal must dial ISDN
Multipoint station number assigned by CM1B, not the ISDN Terminal number assigned by CM10.
13. When a Multiline Terminal calls an ISDN Terminal or an ISDN Terminal calls a Multiline Terminal, a
calling station number is displayed to the calling Multiline Terminal or the ISDN Terminal.
In case of Point to Multipoint connection, the calling station number displayed is the ISDN station number
assigned by CM10.
14. Station to Station Calling between a PS station and an ISDN Terminal is available.
15. Only Preset Dialing can be used from an ISDN Terminal, Overlap dialing is not available.
16. For Event Based CCIS you must have 64K unrestricted digital data connections (circuit mode). The
Telephone company cannot overflow these ISDN calls to analog lines.
Page 12
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
MEGACOM® ACCESS/WATS
MEGACOM® ACCESS/WATS
General Description
AT&T’s MEGACOM® (WATS) network, as well as WATS from other carriers, can be used.
MEGACOM/WATS
PRI
ISDN
NETWORK
NEAX2000 IVS 2
Operating Procedure
No manual operation is required.
Service Conditions
1. The available WATS service is limited to Maximal Subscribed WATS Band (MSB).
2. No specific band will be indicated to the Network.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 13
MEGACOM® 800 SERVICE/800 WATS ULTRA WATS
MEGACOM® 800 SERVICE/800 WATS ULTRA WATS
General Description
AT&T’s MEGACOM® 800 (Inward WATS) network, as well as 800 WATS provided by other carriers, can be
used.
MEGACOM/
800 WATS
ULTRA WATS
PRI
NEAX2000 IVS2
ISDN
NETWORK
MEGACOM 800
800 WATS
ULTRA WATS
Operating Procedure
No manual operation is required.
Service Conditions
1. CM76 can be used to convert indialed digits.
2. The Dialed Number Identification Service (DNIS) must match the station numbering plan (CM20).
3. Multiple DNISs are supported.
Page 14
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
MULTIQUEST®/900 SERVICE
MULTIQUEST®/900 SERVICE
General Description
AT&T’s MultiQuest® service can be used. (It is a “900”-type service.) Also, 900 service provided by other
carriers can be used.
MultiGuest/
900 Service
PRI
ISDN
NETWORK
NEAX2000 IVS2
Operating Procedure
No manual operation is required.
Service Conditions
1. The Dialed Number Identification Service (DNIS) must match the numbering plan (CM20) of the
NEAX2000 IVS2.
2. Multiple DNIS numbers are supported.
3. Command CM76 can be used to convert DNIS digits received from the ISDN Network.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 15
SUBADDRESS–PRESENT
SUBADDRESS–PRESENT
General Description
This feature allows a primary rate interface ISDN trunk to transfer the called party subaddress information to a
destination ISDN station when the call is originated by the NEAX2000 IVS2. Dialing the called party station
number and subaddress is required.
4211
PBX
DTI
DIAL
214-5555000
ISDN
4211
555-5000
CALLING PARTY
SUBADDRESS
Operating Procedure
The calling station dials the ISDN subscriber number (including access code) followed by an asterisk (*), then
dials the called party subaddress followed by a pound sign (#). ISDN automatically recognizes the subaddress
and transfers the information to the destination party.
Service Conditions
1. If the calling party fails to dial the called party subaddress, ISDN cannot transfer any called party subaddress
information to the destination party.
2. If a calling party does not wish to provide a called party subaddress, the call must terminate with a pound
sign (#) (Immediate Start). If a pound sign is not entered, a Timing Start operation begins. The Timing Start
uses the interdigit time-out operation.
3. Subaddress dialing is available only on those telephone terminals that can generate push-button (DTMF)
signals.
4. The called party subaddress must not exceed eight digits.
5. The called party subaddress can be sent with trunk direct dial access.
6. This feature may cannot be used when a call is originated to ISDN using Speed Calling or Call Forwarding
features.
Page 16
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
TRUNK PROVISIONING SERVICE SELECTION
TRUNK PROVISIONING SERVICE SELECTION
General Description
Each channel of a PRI interface can be dedicated to a particular service. Services are designated to specific
channels; once designated, a channel can be used only for that service.
Service A
B-channels
PRI
Service B
D-channel
Operating Procedure
No manual operation is required.
Service Conditions
•
•
The services that can be designated include MEGACOM®/WATS and MEGACOM® 800/800WATS.
Arrangement with the carrier at the time of provisioning is needed.
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 17
This page is for your notes.
Page 18
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0
APPENDIX A: Dterm FIXED FUNCTION KEYS
APPENDIX A: Dterm FIXED FUNCTION KEYS
Series E
Series III
Description
Answer
ANS
To answer a waiting call
Conf
CNF
To establish three-way conversation
Feature
FNC
To activate terminal setup functions and to program One-Touch
Speed Dial/Feature Keys
Hold
HOLD
To place an internal or external call on hold
Recall
LNR/SPD
To terminate established call and re-seize internal dial tone
Redial
RECALL
To active Last Number Call and Speed Calling
Speaker
SPKR
To control the built-in speaker which can be used for Hands Free
dialing/monitoring
Transfer
TRF
To transfer established calls to another station, without attendant
assistance
NEAX2000 IVS 2 ISDN Features and Specifications
NDA-24273, Issue 1.0
Page 19
APPENDIX B: Dterm LCD DISPLAYS
APPENDIX B: Dterm LCD DISPLAYS
Description
Series E
Series III
Clock/Calendar Display
10:06 PM
Busy
BUSY
XXXX
BUSY
XXXX
Restriction
RESTRICT
XXXX
RST
XXXX
Do Not Disturb
DND
XXXX
DND
XXXX
Call Forwarding - All Calls
CF ALL
XXXX
FDA
XXXX
Call Forwarding - Busy Line
CF BUSY
XXXX
FDB
XXXX
Call Forwarding - No Answer
CF NANS
XXXX
FDN
XXXX
Call Transfer
TRANSFER
XXXX
XFR
XXXX
Conference
CONF
XXXX
CNF
Non Exclusive Hold
HOLD
XXXX
HLD
XXXX
Exclusive Hold
E-HOLD
XXXX
EHD
XXXX
Stack Dial
Page 20
MON 21 APR 1999
XXXX
REDIAL[*/#]/SPEED
-1
82625563
10:06 PM
TUE 14
XXXX
RDL[*/#]/SPD
XXXX
-1
82625563
NEAX2000 IVS2 ISDN Features and Specifications
NDA-24273, Issue 1.0