Output:
Product range/positioning
The Xerox DocuPrint 96/4635/180 NPS printing system is fully
compatible with the IBM AFP Group 3 page printer with the Advanced
Function Image and Graphics (AFIG) option. The targeted impressions
per month are as follows:
•
•
•
•
The 96 NPS has one output bin as a standard, with one additional
bin available as an option. The 4635/180 NPS has two output
bins as a standard, with up to two additional bins available as
options.
DocuPrint 96 NPS: 800,000 - 3 million
DocuPrint 4635 NPS: 1.8 million - 4 million
•
DocuPrint 180 NPS: 1.8 million - 6 million
Space requirements
Output bin: Each output bin has a capacity of 2500 sheets of 20
lb. (80 gsm) bond with offset capability
Sample Tray: 100 sheets of 20 lb. (80 gsm) bond
Depth
Note: The following data is accurate for the Sun Ultra 2 workstation
and is presented as an example of typical space requirements for
workstations.
Space requirements for the printer controller are 36 by 36 inches/
91 by 91 cm.
Usage outside this range may vary the service frequency.
Variables other than monthly print volume affect average number of
service calls. Please contact your sales representative or Customer
Service Engineer for more information.
System control module
(High performance Sun workstation)
Processor
Note: This configuration may change due to Xerox policy of staying
abreast of current technology.
Monitor
Reliability performance of the DocuPrint 96/4635/180 NPS for the
targeted impressions per month is as follows:
Average Calls per Month
Average Month
Print Volume
96 NPS
4635 NPS
180 NPS
1 million
2.3
2.5
2.4
2 million
4.6
5
4.8
3 million
6.9
7.5
7.2
4 million
10
•
•
9.6
5 million
12
6 million
14.4
•
•
•
•
•
256 MB RAM
Rigid disk drives:
–
4.2 GB primary disk drive
–
Up to three additional disk drives in increments of 4
or 9 GB
Data can be printed at rates up to 96 pages (96 NPS), 135 pages (4635
NPS), and 180 pages (180 NPS) per minute. Throughput rate can vary
depending upon job complexity and system configuration.
Resolution
96/4635 NPS: 600 by 600 dots per inch (dpi).
•
Ethernet LAN running TCP/IP, AppleTalk, or Novell NetWare
network protocol software.
•
Token Ring running TCP/IP or AppleTalk network protocol
software
•
(For the DP 180 NPS only) Fibre Distributed Data Interface
(FDDI) running TCP/IP, Novell 3.x, or AppleTalk network
protocols (available only with the Solaris 2.x environment). The
FDDI supports a Single Connection configuration only.
Paper handling
DocuPrint does not support both network interfaces simultaneously.
•
•
20 lb. (80 gsm) bond to 110 lb. (200 gsm) index cut-sheet weights
PDL compatibility
Paper sizes: 8 by 10 in. (203 by 254 mm) to
14 by 17 in. (356 by 432 mm), including A4 and A3
The system interprets the following text formats:
•
7 by 10 in. (178 by 254 mm) with the 7 by 10 in. option kit, (4635
and 180 NPS only)
•
Main Tray (Tray 1): 1100 sheet capacity of 20 lb. (80 gsm) bond
paper
•
Auxiliary Tray (Tray 2): 600 sheet capacity of 20 lb. (80 gsm)
bond paper
•
The 4635/180 NPS may have up to six feeder trays: two
processor trays and two to four high-capacity trays.
•
The 96 NPS may have up to four input trays: the two processor
trays and one to two high-capacity trays.
•
21 in.
19 in.
21 in.
Transference of the black toner to poly-vinyl surfaces is a
common occurrence.
53.3 cm
48.3 cm
53.3 cm
•
4mm DAT SCSI tape drive
(optional)
12.25 in.
7.5 in.
2.75 in
Print quality is guaranteed to a range of three to four millimeters
for edge marking and six millimeters for text printing to the edge
of the page.
31 cm
19 cm
7 cm
•
Xerox carbonless paper is approved for DocuPrint 96/4635/180
NPS only. Refer to the Xerox Supplies Catalog for the reorder
numbers.
Keyboard
7.5 in.
20 in.
•
19.1 cm
50.8 cm
Appearance of very small spots is a common occurrence on all
xerographic printers. Consult your Xerox service representative
for details on acceptable spot occurrence specifications.
DocuPrint 96 NPS printer with
inverter feeder/stacker only
One of the following network communications systems may be used to
transport documents from the client workstation to the printer.
180 NPS: 600 by 2400 dots per inch (dpi).
Input:
Special considerations
12.7 cm
Space requirements (physical hardware and required service area)
for each of the printer configurations are:
Interface requirements
Speed
•
•
•
•
•
PostScript level 1
PostScript level 2
PCL5c
114 in.
191 in
290 cm
485 cm
DocuPrint 96/4635/180 NPS
printer with inverter feeder/
stacker and one (1) feeder/
stacker
114 in.
223 in.
290 cm
567 cm
DocuPrint 4635 NPS printer with
inverter feeder/stacker and two
(2) feeder/stackers
114 in.
256 in.
290 cm
649 cm
DocuPrint 180 NPS printer with
inverter feeder/stacker and two
(2) feeder/stackers
114 in.
257 in.
290 cm
652.8 cm
DocuPrint 96/4635/180 NPS
printer with inverter feeder/
stacker and three (3) feeder/
stackers
114 in.
288 in.
290 cm
731 cm
DocuPrint 4635/180 NPS printer 114 in.
with inverter feeder/stacker,
290 cm
feeder/stacker, and bypass
transport modules
242 in.
DocuPrint 4635/180 NPS printer 114 in.
with inverter feeder/stacker and
290 cm
three (2) feeder/stackers, and
bypass transport modules
276 in.
615 cm
701 cm
PCL5e
ASCII
For additional space/configuration options, refer to the Xerox DocuPrint
96/4635/180 NPS Installation Planning Guide (Pub #721P8XXXX).
5 in.
Printer
Operator attention light
•
44.5 cm
4 mm DAT SCSI tape drive (optional)
Black dry ink (permanent)
Customer must supply a table or desk for the Printer Controller.
Work surface must be at least 36” X 36” to provide enough space
for the components and cables.
For proper operation, the printer component must be perfectly
level. On floors less than two degrees out of level, a leveling kit
must be used to level the equipment. The printer will not function
properly on floors more than two degrees out of level.
17.5 in.
Internal CD ROM
Type 4 or 5, 107-keyboard
•
44.5 cm
1.44 MB 3.5-inch diskette drive
21-inch color monitor
The Printer Controller must be positioned within the line-of-sight
of the printer for safety purposes while servicing the equipment.
17.5 in.
Printer module
•
•
Height
Controller
Refer to the Helpful Facts About Paper to help in selection of preprinted
forms, perforated stock and labels.
Performance
Width
•
Note: All the dimensions indicated are taken from the system frame to
the nearest wall or obstruction, shown in inches (centimeters) and are
absolute minimums.
•
There should be a minimum of 78 inches (1,981 mm) clearance
from the floor to the nearest overhead obstruction, throughout the
entire area.
•
4635/180 NPS must be installed in a fixed location with minimum
clearance space of 36 inches/ 914 mm around all sides of each
piece of equipment for access by service personnel.
•
50 inches/1270 mm clearance is required in front of the 4635/180
NPS printer.
Environmental requirements
Recommended
o
o
o
o
Minimum
o
Operating
temperature
72 +/- 4 F
Humidity
45% +/- 10% RH
Maximum
50 F
85o F
30% RH
65% RH
22 +/- 2 C
Normal
Maximum
Altitude
Up to 6,000 feet
above sea level
9,000 feet above
sea level
Heat dissipation
Standby
Running
Printer Module
4,454 BTU/Hr
(Fuser on)
96/4635 NPS:
28,140 BTU/Hr
2,700 BTU/Hr
(Energy Saver)
180 NPS:
32,770 BTU/Hr
System Controller
1,100 BTU/Hr
2. Power requirements of the Bypass Transport are satisfied by the
printer module.
Electrical requirements
System Controller
Printer Module
96/4635 NPS 50 Hz
Voltage
Installation considerations
• Data Cables - Components can be separated up to the length of
the data interface cables that connect them.
100-240 VAC
+/- 10%
—
Delta (3 phase, 4 wire):
220, 230, 240 VAC
•
WYE (star)
(3 phase, 5 wire)
380, 400, 415 VAC
Amperage
15
(power connection per local codes/regulations)
Printer Controller:
8 feet / 2.1 m
Printer:
15 feet / 6 feet/1.8m/4.5m (60 Hz)
•
Cable length loss must be factored in if equipment is installed in a
raised-floor environment. Part of the cable length is routed inside
the equipment to connect with interior power receptacles.
•
All power cords attach to the back of the printer. Listed below are
the distances of the printer power cord attachments from the left
end of the printer as you face it:
96/4635 NPS 60 Hz
Amperage
Power cable lengths are as follows:
Xerox DocuPrint 4635 NPS supports the following types of networked
client workstations and operating systems:
•
•
Sun Workstation running Solaris 1.1.X or Solaris 2.X
•
PC 386 or 486, running MS-DOS, version 6.2, with one or more of
the following TCP/IP packages:
120 VAC
(1 phase)
120/208 VAC; or
120/240 VAC
(2 phase)
15
50
Standard wall outlet
14-50R
—
Cord #1: 36 inches / 914 mm
—
Cord #2: 23 inches / 584 mm (180 NPS only)
Supplies
PC running MS-DOS 6.2 and Microsoft Windows 3.1, using
Ethernet with TCP/IP or Novell NetWare, Windows95, Windows
NT
1. PathWay Access 3.1, Wollongong Integrated Networking/
Transmission Control Protocol (WIN/TCP) for DOS, release
6.0
Delta (3 phase, 4 wire): 30
WYE (star)
(3 phase, 5 wire): 20
Voltage
Printer and systems controller = 20 foot/6.1 m data cable
Supported hardware and operating systems
2. FTP software, PC-TCP/IP for DOS, release 6.0
3. Sun Personal Computer Network File Services (PC-NFS),
version 5.1
•
•
•
•
IBM RS/6000 running IBM AIX, version 4.1
HP/Apollo running HP-UX, version 10.01
DECStation 5000/200 running DEC Ultrix, version 4.3
•
Apple Macintosh, System 7 (7.5), using AppleTalk through
EtherTalk, phase 1 or 2
•
Any system that supports RFC-1179 lpr/lpd
Expected Yield
(Prints/Carton)
Dry Ink
6R206
180,000
Dry Ink, MICR
6R819
180,000
Operating Mode
Dry Ink waste bottle
93K460
N/A
Receptacle
Diagram
Developer
5R161
1,000,000
Customer benefits of using this technology include:
Developer, MICR
5R573
600,000
•
Diagnostic help and identification of required parts before the
service visit
Fuser agent
8R2955 (1 bottle)
250,000
•
Planned visits based on known problems and/or replacement of
wear-out items
•
Customer self-maintenance to provide faxed replacement change
reminder to trained operators.
Power
Consumption
KVA Rating
0.8
7.3
(+.75 per middle module)
180 NPS 60 Hz
Printer Module
Printer Module
Cord #1
Cord #2
Voltage
See 96/4635
NPS
120/208 VAC;
or
120/240 VAC
(2 phase)
120/208 VAC;
or
120/240 VAC
(2 phase)
Amperage
See 96/4635
NPS
50
30
Receptacle
NEMA Part No.
See 96/4635
NPS
14-50R
14-30R
Power
Consumption
KVA Rating
See 96/4635
NPS
7.3
7.3
Notes:
•
Expected dry ink yield is based on a 7% area coverage, 8.5”X 11”
paper, and will vary depending on area coverage of the
application, as well as the darkness settings of the printer.
•
The Xerox Supplies Marketing Center, 1.800.822.2200, is
available for ordering Xerox supplies, including paper and other
throughput material.
Quick Reference Card
Diagnostics (Sixth Sense Technology)
Sixth Sense technology is a user-friendly suite of tools that allow
service personnel to connect with a customer system and evaluate its
performance while the system is being used. The Customer Service
Engineer (CSE) can troubleshoot problems remotely, transfer, apply,
and remove patches remotely, and, if an on-site call is required, arrive
with the solution to fix the problem.
I
System
Controller
Customer Information
VAXStation 2000 running DEC VMS, version 5.5, with WIN/TCP,
version 5.1
Reorder # (US)
Receptacle
NEMA Part No.
Xerox DocuPrint
96/4635/180 NPS
The Sixth Sense feature is available to customers at no charge through
Xerox Service. Customers need to provide an analog phone line for
use by the Sixth Sense modem connection, and a 120 Volt outlet for
the modem to connect to. Customers unable to dedicate a phone line
to the Sixth Sense connection may purchase three or five port phone
share devices.
(+.75 per middle (+.75 per middle
module)
module)
Operating Mode
Receptacle
Diagram
See 96/4635
NPS
Notes:
1. Dedicated service is required for each component. Each power
cord must have a separate circuit.
1999, 2000 by Xerox Corporation. All rights reserved.
Version 7.1
August 2000
721P88521
">
