Nikon | MSV-01 | User's Manual | Nikon MSV-01 User's Manual

En
Introduction
Preparation
Basic Operation
Organizing Images
Saving Images to a Computer
Advanced Operation
Technical Notes
Index
(En)
User's Manual
Trademark Information
•
Apple, the Apple logo, Macintosh, Mac OS, Power Macintosh, PowerBook, and Quick Time are
registered trademarks of Apple Computer, Inc.
•
Finder, Power Mac, iMac, and iBook are trademarks of Apple Computer, Inc.
•
Microsoft and Windows are registered trademarks of Microsoft Corporation.
•
Internet is a trademark of Digital Equipment Corporation.
•
CompactFlash™ is a trademark of SanDisk Corporation.
•
Lexar Media is a trademark of Lexar Media Corporation.
•
Adobe and Acrobat are registered trademarks of Adobe Systems Inc.
•
Epson and USB Direct Print are trademarks of Seiko Epson Corporation.
•
PictBridge is a trademark.
•
All other trade names mentioned in this manual or the other documentation provided with
your Nikon product are trademarks of their respective holders.
Introduction
Thank you for your purchase of the Nikon COOLWALKER MSV-01 digital photo storage viewer.
This manual has been written to help you get the most out of your Nikon COOLWALKER MSV-01.
To make it easier to find the information you need, the following symbols and conventions are used:
This icon marks cautions,
information that should be read
before use to prevent damage to
your COOLWALKER MSV-01.
This icon marks notes, information
that should be read before using
your COOLWALKER MSV-01.
This icon marks tips, additional
information that may be helpful when
using your COOLWALKER MSV-01.
This icon indicates that more
information is available elsewhere
in this manual.
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others, read the following
safety precautions in their entirety before using this equipment. Keep these safety instructions
where all those who use the product will read them.
The consequences that could result from failure to observe the precautions listed in this section
are indicated by the following symbol:
This icon marks warnings, information that should be read before using this Nikon
product to prevent possible injury.
Warnings
Turn off immediately and unplug in
the event of malfunction
Should you notice excessive heat, smoke or
an unusual smell coming from the
equipment or from the AC adapter, unplug
the AC adapter and remove the battery pack
immediately, taking care to avoid burns.
Continued operation could result in injury or
fire. After removing the battery pack, take
the equipment to a Nikon-authorized service
representative for inspection.
Do not use in the presence of
flammable gas
Do not use electronic equipment in the
presence of flammable gas, as this could
result in explosion or fire.
Do not disassemble or modify
Touching the product's internal parts could
result in injury. In the event of malfunction,
the product should be repaired only by a
qualified technician. Should the product
break open as the result of a fall or other
accident, take the product to a Nikonauthorized service representative for
inspection after unplugging the AC adapter
and removing the battery pack.
Keep dry
Do not immerse in or expose to water
Continuing to use the product under such
circumstances may cause fire or an electric
shock.
i
Introduction—For Your Safety
Read this manual thoroughly before use, and keep it where all those who use the product will
read it.
Do not place the strap around the
neck of an infant or child
Placing the case strap around the neck of an
infant or child could result in strangulation.
Introduction—For Your Safety
Use only the specified batteries and
AC adapter
Using non-specified accessories may cause
fire or an electric shock.
Use appropriate cables
When connecting cables to the input and
output jacks, use only the cables provided or
sold by Nikon for the purpose, to maintain
compliance with product regulations.
• Use only Rechargeable Lithium-ion Polymer
Battery EN-EL6 (the battery pack) for the
main unit. To charge the battery pack, attach
it to the MSV-01 and connect the supplied
AC adapter. Do not use any other device or
method to charge the battery pack.
• Use only CR2025 Lithium Battery for the
remote control unit.
• When inserting the batteries, do not
attempt to insert them upside down or backwards.
Keep out of reach of children
• Do not short or disassemble the batteries.
Particular care should be taken to prevent
infants from putting the small parts into
their mouths.
• Do not expose the batteries to flame or to
excessive heat.
Do not touch the power plugs during
thunderstorms while you are using
the AC adapter
• Do not transport or store with metal objects
such as necklaces or hairpins.
Failure to observe this precaution may lead
to an electric shock.
Keep clear of the device until the
thunderstorm has stopped.
Removing memory cards
Memory cards may become hot during use.
Observe due caution when removing
memory cards from the MSV-01.
CD-ROMs
The CD-ROMs on which the software and
manuals are distributed should not be
played back on audio CD equipment. Playing
CD-ROMs on an audio CD player could cause
hearing loss or damage the equipment.
Avoid contact with liquid crystal
Should the monitor break, care should be
taken to avoid injury due to broken glass
and to prevent liquid crystal from the
monitor touching the skin or entering the
eyes or mouth.
Observe proper precautions when
handling the batteries
The batteries may leak or explode if
improperly handled. Observe the following
precautions when handling the batteries for
use in this product:
ii
• Before replacing the battery pack, turn the
product off and make sure the power-on
lamp has gone out. If you are using an AC
adapter, be sure it is unplugged.
• Do not immerse in or expose to water.
• Batteries are prone to leakage when fully
discharged. To avoid damage to the product,
be sure to remove the batteries when no
charge remains.
• Stop charging the battery pack if charging
fails to complete once the specified charging
time has been exceeded.
• Immediately after use, or when the product
is used on battery power for an extended
period, the battery pack may become hot.
Before removing the battery pack, turn the
device off and allow the battery pack to cool.
• Discontinue use immediately should you
notice any change in the batteries, such as
discoloration or deformation.
• Take warning and caution labels on the batteries seriously and follow all safety precautions.
• If leaked fluid from the batteries comes in
contact with the eyes, rinse in clean water
and seek medical attention immediately.
Wash off any leaked fluid from the batteries
that comes into contact with skin or clothing
immediately using clean water.
• Keep out of reach of children. Particular care
should be taken to prevent infants from putting the batteries into their mouths. Should
they swallow, seek medical attention immediately.
Observe proper precautions when
using the AC adapter
Introduction—For Your Safety
Improper use of the AC adapter may result in
electric shock or fire. Observe the following
precautions when using the AC adapter with
this product:
• Do not disassemble, repair or modify the AC
adapter.
In the event of malfunction or should the AC
adapter break open as the result of a fall or
other accident, unplug and take the AC
adapter to a Nikon-authorized service representative for inspection.
• Keep dry.
• Do not use in the presence of flammable gas.
• Keep the AC adapter clean of dust. If dust or
grime becomes attached to the metal contacts or body of the power plug, remove it
with a dry cloth. Continuing to use the product in these circumstances may cause fire.
• Do not connect or disconnect the AC adapter
power plug with wet hands, as this may
cause an electric shock.
iii
Notices
Introduction—Notices
•
No part of the manuals included with this product may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any
means, without Nikon’s prior written permission.
•
Nikon reserves the right to change the specifications of the hardware and software described
in these manuals at any time and without prior notice.
•
Nikon will not be held liable for any damages resulting from the improper use of this product.
•
While every effort has been made to ensure that the information in these manuals is accurate
and complete, we would appreciate it were you to bring any errors or omissions to the attention of the Nikon representative in your area (address provided separately).
Notice for customers in the U.S.A.
Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
MSV-01
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/
television technician for help.
CAUTIONS
Modifications
The FCC requires the user to be notified that
any changes or modifications made to this
device that are not expressly approved by
Nikon Corporation may void the user's authority to operate the equipment.
Interface Cables
Use the interface cables sold or provided by
Nikon for your equipment.
Using other interface cables may exceed the
limits of Class B Part 15 of the FCC rules.
Notice for customers in the State of California
WARNING: Handling the cord on this product
will expose you to lead, a chemical known to
the State of California to cause birth defects or
other reproductive harm.
Wash hands after handling.
Nikon Inc.,
1300 Walt Whitman Road, Melville, New York
11747-3064, U.S.A.
Tel.: 631-547-4200
iv
Notice for customers in Canada
ATTENTION
This class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte
toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that has been digitally copied or reproduced by
means of a scanner, digital camera or other device may be punishable by law.
• Items prohibited by law from being
copied or reproduced
Do not copy or reproduce paper money,
coins, securities, government bonds, or
local government bonds, even if such copies or reproductions are stamped “Sample.”
The copying or reproduction of paper
money, coins, or securities which are circulated in a foreign country is prohibited.
Unless the prior permission of the government has been obtained, the copying or
reproduction of unused postage stamps or
post cards issued by the government is prohibited.
• Comply with copyright notices
The copying or reproduction of copyrighted creative works such as books,
music, paintings, woodcut prints, maps,
drawings, movies, and photographs is governed by national and international copyright laws.
Do not use this product for the purpose of
making illegal copies or to infringe copyright laws.
The copying or reproduction of stamps
issued by the government and of certified
documents stipulated by law is prohibited.
• Cautions on certain copies and reproductions
The government has issued cautions on
copies or reproductions of securities issued
by private companies (shares, bills, checks,
gift certificates, etc.), commuter passes, or
coupon tickets, except when a minimum of
necessary copies are to be provided for
business use by a company.
Also, do not copy or reproduce passports
issued by the government, licenses issued
by public agencies and private groups, ID
cards, and tickets, such as passes and meal
coupons.
v
Introduction—Notices
CAUTION
A built-in hard disk drive requires careful handling.
Introduction—Notices
This Product is a High-precision Device Containing Internal Hard Disk Drive.
• Read "For Your Safety" and "Caring for Your COOLWALKER MSV-01" before use, and be very careful
when handling the product. Damage to the hard disk drive will not only require high repair
expenses, but can also cause corruption or irreversible loss of the stored data.
• After copying, moving recorded data, or performing any other saving operation, confirm that the
data have been correctly stored in the destination location.
• Ensure that your data is backed up using another recording medium.
Nikon will not be held liable for any damages resulting from deletion, loss and damage of recorded
data.
Use only electronic accessories approved for use with this product
This product is designed to the highest standards and includes complex electronic circuitry. Only the
electronic accessories (including battery pack and AC adapter) certified by Nikon specifically for use with
this Nikon product are engineered and proven to operate within the operational and safety
requirements of this electronic circuitry.
THE USE OF ELECTRONIC ACCESSORIES NOT APPROVED BY NIKON SPECIFICALLY FOR USE WITH THIS
PRODUCT COULD DAMAGE THIS PRODUCT AND MAY VOID YOUR NIKON WARRANTY.
The use of third-party rechargeable Li-ion polymer batteries not approved by Nikon could interfere with
normal operation of this Nikon product or result in the batteries overheating, igniting, rupturing, or
leaking.
For more information about Nikon brand accessories, contact a local authorized Nikon dealer.
Life-Long Learning
As part of Nikon's “Life-Long Learning” commitment to ongoing product support and education,
continually-updated information is available on-line at the following sites:
• For users in the U.S.A.: http://www.nikonusa.com/
• For users in Europe: http://www.europe-nikon.com/support
• For users in Asia, Oceania, the Middle East, and Africa: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently asked
questions (FAQs), and general advice on digital imaging and photography. Additional information may
be available from the Nikon representative in your area. See the URL below for contact information:
http://nikonimaging.com/
vi
Table of Contents
Introduction
i
Preparation
Table of Contents
For Your Safety ................................................................................................................... i
Notices............................................................................................................................... iv
1
About the COOLWALKER MSV-01 .................................................................................... 1
Check the Package Contents............................................................................................. 2
Parts of the COOLWALKER MSV-01.................................................................................. 3
Main Unit ................................................................................................................. 3
Remote Control Unit ............................................................................................... 5
Navigating the Menus....................................................................................................... 6
Installing and Charging the Battery Pack ........................................................................ 8
Power-ON/OFF ................................................................................................................. 10
Checking the Battery Level ............................................................................................. 10
Setting Display Language ............................................................................................... 11
Basic Operation
12
Inserting a Memory Card ................................................................................................ 12
Copying Images from a Memory Card (Copy CF card ➡ HDD)...................................... 13
Viewing Images Stored on the COOLWALKER MSV-01 (Play HDD images)................. 14
Displaying Image Information ........................................................................................ 16
Taking a Closer Look: Playback Zoom ............................................................................ 17
Viewing Images Stored on a Memory Card (Play CF card images) ............................... 17
Button Operations (List View and Image Playback) ...................................................... 19
List View ................................................................................................................. 19
Thumbnail Playback .............................................................................................. 20
Full-Screen Playback .............................................................................................. 21
Movie Playback ...................................................................................................... 22
Organizing Images
23
The EDIT Menu ................................................................................................................ 23
Displaying the EDIT Menu .................................................................................... 23
Delete ..................................................................................................................... 24
Move ...................................................................................................................... 25
Copy ....................................................................................................................... 26
New folder ............................................................................................................. 27
Rename .................................................................................................................. 28
Search ..................................................................................................................... 28
Saving Images to a Computer
30
Driver Software Installation (Windows 98 Second Edition Only) ....................... 30
Connecting the USB Cable .............................................................................................. 32
Copying Images to the Computer .................................................................................. 33
Disconnecting the COOLWALKER MSV-01 ..................................................................... 34
vii
Advanced Operation
35
Table of Contents
Viewing Pictures on TV ................................................................................................... 35
Copying Images to a Memory Card (Copy HDD ➡ CF card) .......................................... 36
Copying All Images in a Selected Folder .............................................................. 36
Copying a Selected Image ..................................................................................... 37
Printing Pictures............................................................................................................... 38
DPOF printset................................................................................................................... 39
Printing Via Direct USB Connection (PictBridge) ........................................................... 42
Connecting to a Printer ......................................................................................... 42
Printing Images Stored on the MSV-01 ................................................................ 43
Printing Images Stored on a Memory Card ......................................................... 45
Printing Images Stored on a Memory Card Using DPOF Settings ...................... 46
Finishing Direct Printing ....................................................................................... 47
Slideshow ......................................................................................................................... 48
Playing All Images in HDD .................................................................................... 48
Playing All Images in a Selected Folder ............................................................... 49
Playing Selected Images ........................................................................................ 49
Operations During the Slideshow ........................................................................ 51
Deselect images ..................................................................................................... 51
Set interval ............................................................................................................. 52
The SET UP Menu............................................................................................................. 53
Brightness .............................................................................................................. 53
Language ............................................................................................................... 54
Auto power off ...................................................................................................... 54
Video mode ........................................................................................................... 54
Format (CF Card/HDD) ........................................................................................... 55
The INFORMATION Screen .............................................................................................. 56
Displaying Memory Information .......................................................................... 56
Technical Notes
Optional Accessories........................................................................................................
Caring for Your COOLWALKER MSV-01.........................................................................
Error Messages.................................................................................................................
Troubleshooting ..............................................................................................................
Specifications ...................................................................................................................
Index
viii
57
57
58
62
64
65
67
Preparation
About the COOLWALKER MSV-01
The diagram below illustrates the functions of the MSV-01.
Preparation—About the COOLWALKER MSV-01
Supported Image Data Formats
• The COOLWALKER MSV-01 supports image data recorded with Nikon digital cameras (DCF format).
• The COOLWALKER MSV-01 supports NEF (Nikon Electronic Image Format) files (RAW files containing
embedded preview images).
• Images taken with cameras from other manufacturers or images edited using a computer may not be
displayed or printed correctly.
• The DPOF printset function supports only JPEG images stored on a CompactFlash™ card.
• The COOLWALKER MSV-01 supports JPEG images for printing via direct USB connection (PictBridge).
• For information on image data supported for displaying, please see "Image Data Supported for Playback" (
15) and "Specifications" (
65).
1
Check the Package Contents
Unpack the COOLWALKER MSV-01 box and check the contents to make sure that you have all the
items listed below.
Preparation—Check the Package Contents
COOLWALKER MSV-01
AC Adapter DSA-0151F-05
User's Manual (this manual)
Remote Control Unit ML-CW1
(CR2025 Lithium Battery included)
Warranty
Audio/Video (A/V) cable EG-CW1
Soft Case CF-CW1
USB interface cable UC-E9
MSV-01 Windows® 98 SE Driver Installer CD
Battery pack case (for use with the removed battery
pack)
2
Parts of the COOLWALKER MSV-01
Main Unit
HDD Access lamp (flashes
during reading from or
writing to the internal HDD)
Preparation—Parts of the COOLWALKER MSV-01
Power-on lamp
(
10)
Power switch
(
10)
LCD Monitor
Right function button
(Right button)
(
6)
Multi selector
(
6)
Left function button
(Left button) (
6)
Enter button
(
6)
Memory card slot
(
12)
Remote-control sensor
(
6)
Memory card slot cover
(
12)
3
Preparation—Parts of the COOLWALKER MSV-01
DC-in connector (
Interface connector cover
Audio/Video-out connector (
35)
USB connector (
8)
30, 42)
Interface connector cover
Battery pack (Rechargeable
Li-ion Polymer Battery EN-EL6)
(
8)
Battery release button
(
8)
Battery Release Button
• Do not press the battery release button when charging the battery pack or when operating the MSV-01.
• Make sure to turn the MSV-01 main unit off and disconnect the AC adapter before removing the battery pack.
4
Remote Control Unit
Remote control transmitter
Power OFF button
(
10)
Rotate button
Preparation—Parts of the COOLWALKER MSV-01
Left function button
(Left button)
(
6)
Right function button
(Right button) (
6)
Multi selector
(
6)
Enter button
(
6)
Battery holder (CR2025 lithium battery)
Before Using the Remote Control Unit Remove the Insulating Tape.
The remote control unit is shipped with an insulating tape in the battery
holder. Before using the remote control unit remove the insulating tape,
pulling it in the direction indicated by the arrow.
Insulating
Tape
Inserting the CR2025 Lithium Battery
1. Press the latch inwards (➀) and pull out the battery holder (➁) at the base of the remote
control unit in the direction indicated by the arrow in the illustration.
2. Place the battery in the battery holder (➂).
3. Insert the battery holder into the remote control unit. Push it in until the latch locks in place (➃).
Make sure that the positive (+) side of the battery
is in correct orientation as indicated on the back
of the remote control unit.
➀
Battery holder latch
➁
➂
➃
5
Navigating the Menus
.
Main menu
Preparation—Navigating the Menus
Right function button
(Right button)
Executes commands
displayed bottom-right
Left function button
(Left button)
Executes commands
displayed bottom-left
Enter button
Remote Control Unit
Multi selector
Power off
button
Press
to move cursor up.
Press
to move cursor down.
Press
Rotate
button
to display sub-menu.
• In the list view: Press
to open a folder (
19).
• In the list view: Press
to close a folder (
19).
Multi Selector and Enter Button
•
Use the multi selector to navigate through menus and make selections. The currently selected
menu item is highlighted.
•
Press enter button
•
on the multi selector may perform the same function as the enter button, i.e. open the submenu screen.
to execute a highlighted entry.
Function Buttons
The Left function button (Left button) and Right function button (Right button) perform the
functions shown at the bottom left and right corners of the monitor, respectively.
Remote Control Unit
•
Operate the remote control unit pointing it at the remote-control sensor located beside the
memory card slot of the main unit (
3).
•
The Power OFF button on the remote control unit turns the MSV-01 main unit off.
•
The Rotate button rotates, by 90° steps counter-clockwise, the image currently displayed in
full-screen playback mode (
15).
•
All buttons except for the Power OFF and Rotate buttons on the remote control work in the
same way as the equivalent buttons on the MSV-01 main unit.
6
The Main Menu
When the MSV-01 is turned on, the monitor briefly displays a welcome screen, and then takes you
to the main menu.
Item
Preparation—Navigating the Menus
Memory Card Inserted
Memory Card not Inserted
Description
Copy CF card ➡ HDD
Copy all the data recorded within a memory card onto
the MSV-01 hard disk drive.
Play HDD images
View image files stored on the MSV-01 hard disk drive.
14
Play CF card images
View image files stored on a memory card.
17
Copy HDD ➡ CF card
Copy data stored on the MSV-01 hard disk drive to a
memory card.
36
Print
Print to a PictBridge printer connected to the MSV-01 via
direct USB connection, or set DPOF printing for image
files saved on a memory card.
38
Slideshow
View image files stored on the MSV-01 hard disk drive in
an automated slideshow.
48
SET UP (Left button)
Press SET UP (Left button) to display the SET UP menu
allowing to perform basic settings.
53
INFO. (Right button)
Press INFO. (Right button) to display the INFORMATION
screen allowing to confirm the free space on the MSV-01
hard disk drive or memory card.
56
13
If no memory card is inserted, the Copy CF card ➡ HDD, Play CF card images and Copy HDD ➡
CF card options are not available.
The EDIT Menu
To display the EDIT menu (
23), press EDIT (Right button) when a folder or a file are selected
while using the Play HDD images or Play CF card images options. Use the EDIT menu to
delete, copy, move, rename image files of folders, create new folders or perform search for
images taken within a specified range of dates.
7
Installing and Charging the Battery Pack
Before Using the COOLWALKER MSV-01 Remove the Insulating Tape.
The battery pack is shipped with an insulating tape
over its terminal.
(1) Remove the battery pack from the MSV-01 main
unit following the instructions provided in the
"Removing the Battery Pack" section below.
Preparation—Installing and Charging the Battery Pack
Insulating
tape
Terminals
(2) Remove the insulating tape from the battery pack.
(3) Reinstall the battery pack following the instructions provided in the "Installing the Battery Pack"
section below.
1
➂
➁
➀
2
➆
➄
➅
Power-on lamp
Installing the Battery Pack
(1) Align the battery pack horizontally with the bottom of the MSV-01 main unit as shown on the
illustration (➃). Make sure that the battery pack
terminals do not extend over the main unit protruding part (➄).
➃
➄
Removing the Battery Pack
Push the battery release button (➀) and slide the battery pack in the direction of the arrow (➁) to remove
it from the the MSV-01 main unit (➂).
(2) Slide the battery pack in the direction of the
arrow onto the bottom of the MSV-01 main unit
until it locks into position (➅). Make sure that the
battery pack is fully seated as shown on the illustration (➆, ➇).
➇
3
Charging the Battery Pack
To charge the battery pack, it must first be installed
on the MSV-01 main unit.
(1) Make sure that the power-on lamp on the MSV-01
main unit is off.
8
(2) Open the interface connector cover, and connect
the supplied AC adapter to DC-in connector (➈).
Plug the AC adapter into an outlet (➉).
(3) Charging will begin immediately.
While the battery is charging, the power-on lamp
flashes in orange. Charging is complete when the
orange power-on lamp stops flashing.
An exhausted battery can be fully charged in
about 4.5 hours.
➉
(4) Remove the AC adapter, while the MSV-01 is still
off.
Using the COOLWALKER MSV-01 from an AC Power Supply Source
• To use your MSV-01 from an AC power source, connect the AC adapter and turn the power switch on.
• Charging is not performed when the MSV-01 is on with the AC adapter connected.
Removing and Installing the Battery Pack
• Before removing the battery pack make sure that the MSV-01 is turned off and the AC adapter is disconnected.
• When removing or attaching the battery pack, always observe the correct procedure described in this
manual to avoid damaging the battery terminals.
• Do not touch the battery pack terminals to avoid damaging them and prevent them from becoming
dirty.
• Do not leave unattended or transport the MSV-01 with the battery pack removed.
• Do not remove the battery pack when using the MSV-01 from an AC power supply source. If you accidentally connect the AC adapter to the MSV-01 with the battery pack removed, the power-on lamp
will light up (orange). Make sure that the MSV-01 is off, disconnect the AC adapter and attach the
battery pack.
The AC Adapter
• Accidental disconnection of the AC adapter while the MSV-01 is turned on may damage the device.
When using the device, be careful not to disconnect the AC adapter.
• Be sure to read and follow the precautions in the "For Your Safety" (
i-iii) section and notes on
using the AC adapter (
59) in this manual.
The Battery Pack
• When transporting or storing a spare battery pack, place it in the supplied case.
• On handling the battery pack, refer to the Li-ion Polymer Battery EN-EL6 manual. When installing or
removing the battery pack, be sure to read and follow the precautions in the "For Your Safety"
(
i-iii) and "Notices" (
iv - vi) sections, as well as notes on using the battery pack in the
"Batteries" (
60) section in this manual.
9
Preparation—Installing and Charging the Battery Pack
➈
Power-ON/OFF
To power the MSV-01 on, press and hold down the power switch (
3) for about 2 seconds. The
monitor will turn on showing the welcome screen, then it will switch to the main menu. To turn
the MSV-01 off, press and hold down the power switch for about 2 seconds when the power-on
lamp is on.
The MSV-01 status is shown as follows:
Preparation—Power-ON/OFF
Power switch
Power-on lamp
Power-on Lamp
ON (green)
COOLWALKER MSV-01
Power ON
OFF
Power OFF
Blinking (orange)
Charging (OFF)
On (orange)
Charging completed (OFF)
Turning the Power On/Off
• Be sure to turn the MSV-01 off, when:
- inserting or removing a memory card;
- connecting or disconnecting the A/V cable;
- removing the battery pack.
• The MSV-01 will not go off if the power switch is pressed while the copy (
13, 26, 36), or HDD/
memory card format (
55) operation is in progress and "Copying..." or "Formatting..." is
displayed on the monitor.
Auto Power Off
If no operation is performed for one minute (default setting) when running on battery power, the MSV01 will turn off automatically.
• This setting can be changed using the Auto power off option in the SET UP menu (
54).
• The Auto power off function is disabled when the MSV-01 is running on the AC power supply.
Checking the Battery Level
The battery status is displayed at the bottom of the MSV-01 monitor.
Display
Description
Battery is fully charged.
Battery power is low. The power may go off during operation.
Battery is exhausted. Recharge or use the AC
adapter immediately.
Battery status
Not displayed
The MSV-01 is operating from an AC power
source.
During operation, the display may temporarily indicate a lower than the actual remaining battery
charge.
Using the MSV-01 from an AC Power Source
To power the MSV-01 continuously for extended periods, use the DSA-0151F-05 AC adapter. Do not,
under any circumstances, use another make or model of an AC adapter. Failure to observe this
precaution could result in overheating or in damage to the MSV-01.
10
Setting Display Language
1
2
3
Highlight Language using
press
or
and
.
4
Highlight Deutsch (German), English,
Español (Spanish), or Français (French),
and press
.
Press MENU (Left button) to return to the
main menu.
The selected language will be set for
menus and messages and the screen will
return to the SET UP menu.
11
Preparation—Setting Display Language
Press SET UP (Left button) to display the
SET UP menu.
Basic Operation
Inserting a Memory Card
To copy image data from a memory card to the MSV-01 or from the MSV-01 to a memory card,
insert a CompactFlash™ memory card into the memory card slot.
1
Turn the MSV-01 off
Confirm that the monitor is off and the power-on lamp is off
or, if the AC adapter is connected, is lit or flashing orange
(
10).
Basic Operation—Inserting a Memory Card
2
Open the memory card slot cover
Gently slide the memory card slot cover downwards to expose
the memory card slot.
Terminals
Direction of
insertion
3
Insert a memory card
Insert a memory card into the memory card slot in the direction shown on the illustration.
Insert the memory card firmly, but without excess force.
Front
(When correctly inserted, a CompactFlash™ memory card
protrudes approximately 12 mm from the MSV-01 main unit.)
Inserting Memory Cards
12mm
• Insert the memory card terminals first. Inserting the card
upside down or backwards could damage the MSV-01 or the
card. Check to be sure that the card is in the correct orientation.
• Perform all operations on a table or any other stable flat surface to avoid dropping the MSV-01 or memory cards.
Removing Memory Cards
Memory cards can be removed without loss of data when the MSV-01 is off. To remove a memory card,
turn the MSV-01 off and confirm that the power-on lamp is off or, if the AC adapter is connected, is lit or
flashing orange. Then grasp the protruding section of the memory card, and pull it out.
Note that memory cards may become hot during use. Observe due caution when removing memory
cards from the MSV-01.
Supported Memory Cards
The memory card slot accepts CompactFlash™ memory cards (Type I and II).
On memory cards approved for use with the COOLWALKER MSV-01 see "Approved Memory Cards"
(
57).
12
Copying Images from a Memory Card (Copy CF card ➡ HDD)
Use Copy CF card ➡ HDD from the main menu to copy all data recorded within a memory card
onto the MSV-01.
1
Insert a memory card into the memory card slot (
12), then turn the
MSV-01 on.
The monitor will go on and display the main menu.
When using the battery pack, check the battery level (indicated on the
monitor) (
10).
3
Highlight Copy CF card ➡ HDD using
Press
or
Copying will begin immediately. "Copying..."
is displayed on the monitor while copying is in
progress. Press CANCEL (Left button) to abort
copying.
.
.
Copying Images
4
When "Copy finished" is displayed, press
(OK) to return to the main menu.
• Do not expose the device to shocks or vibration during copy operation.
• Do not remove the memory card or AC
adapter during copy operation.
• Using Play HDD images (
14), confirm that
the data have been stored on the MSV-01 hard
disk.
Deleting Copied Images or Folders
To delete copied images or folders, use Delete option (
24) from the EDIT menu (
23).
Files Copied onto the MSV-01
Each time you copy data from a memory card, the MSV-01 creates a new folder on its HDD and
stores all the images in that folder.
The folder name is a number representing the date of the latest recording in the memory card, in
the format "YYYYMMDD.NNN".
YYYY is the year, MM is the month, DD is the day, NNN is a running serial number starting from 001 to distinguish folders created on the same date (e.g.: 20040601.001).
Date Setting
To ensure that the copied folder names reflect the dates on which your
pictures are taken and use the Search function (
28), make sure that your
digital camera clock is correctly set.
13
Basic Operation—Copying Images from a Memory Card (Copy CF card ➡ HDD)
2
Viewing Images Stored on the COOLWALKER MSV-01 (Play HDD images)
Use Play HDD images from the main menu to view images stored on the MSV-01.
1
2
Basic Operation—Viewing Images Stored on the COOLWALKER MSV-01 (Play HDD images)
Highlight Play HDD images using
.
or
Press
. You will see a list of folders
stored on the hard disk.
• The
icon at the top of the screen
represents the root folder on the MSV-01
hard disk.
3
4
Using
or
, highlight a folder.
Press
Using
• Press
5
to hide a list of sub-folders.
6
Press
to display a list of sub-folders in the
DCIM folder. Using
or
, highlight a
folder containing images inside the DCIM
folder (example: 100NCD70, 100NIKON etc.).
7
Press
to display thumbnails of images
and sub-folders inside the folder.
8
Select an image to play full-screen, moving
the cursor (a yellow frame) with
,
,
or
.
• The name of the currently selected file is
displayed bottom-left.
14
to display a list of sub-folders in the folder.
or
, highlight the DCIM folder.
Press
to view the selected image in fullscreen playback.
To display the next or previous images,
press
or
on the multi selector.
9
Press
(Left button) to return to thumbnail playback (Step 7). Press LIST (Left button) to return to
the list view (Step 5), and then press MENU (Left button) to return to the main menu.
Image Data Supported for Playback
Viewing Images in Rotated Orientation
In full-screen playback mode, still images can be displayed in rotated orientation.
To change the orientation of a still image, press the Rotate button
on the remote control unit
(
5). This button rotates the displayed image 90º counter-clockwise each time you press it.
Viewing Movies
Movies can be played in full-screen playback mode.
When
(a movie icon) is shown for the currently displayed image, press
(
22).
to begin movie playback
Operations during Playback
For button operations available during playback, see pg.20-22.
15
Basic Operation—Viewing Images Stored on the COOLWALKER MSV-01 (Play HDD images)
• Only image files and sub-folders in the selected folder are displayed in the thumbnail playback mode.
The
icon is displayed for images not supported for playback on the MSV-01.
• Only image files are displayed in the full-screen playback mode.
• The COOLWALKER MSV-01 provides support for the image data recorded with Nikon digital cameras
(DCF format).
• The COOLWALKER MSV-01 supports NEF (RAW) files containing embedded JPEG preview images.
• Large size images may not be displayed correctly.
• Images hidden with a camera will also be played.
• Images taken with cameras from other manufacturers or images edited using a computer may not be
displayed or printed correctly.
• In thumbnail playback, movies are indicated by
(a movie icon). In full-screen playback,
(a
movie icon) and movie playback guide are displayed (
16).
• For image files with attached voice memos, in full-screen playback
(a voice memo icon) and a voice
memo playback guide are displayed (
16).
• File and folder names, set or edited using the computer, may not be displayed correctly on the MSV-01.
• Long file and folder names that exceed maximum length will be abbreviated with an asterisk (*).
Displaying Image Information
Image information is superimposed on images displayed in full-screen playback (
There are five pages of image information for each image. Press
through image information as follows:
➀
➁
➂
Basic Operation—Displaying Image Information
➃
➄
➅
➆
1
➇
➈
Viewing an image with File Information (displayed
by default)
➀ Date of recording
➅ Folder name
➁ Time of recording
➆ File name
➂ Zoom guide
➃ Print-order icon (
➇ Voice memo
40)
/Movie icon
*
➈ Voice/Movie Playback guide*
➄ Image size (Pixels)
➀
➁
➂
➃
➄
14, 18).
on the multi selector to cycle
* Displayed only for images with an
attached voice memo or movies.
2
Viewing an image without File Information
3
Shooting Data 1**
➀ Camera type
➁ Metering method
➂ Exposure mode
➃ Shutter speed
➀
➁
➂
➃
➄
➅
4
➄ File name
Shooting Data 2**
➀ Aperture
➁ Exposure compensation
➂ Focal length (Digital zoom ratio)
➃ File size
➄ Sensitivity (ISO equivalency)
5
➅ White balance
Histogram
Shows the distribution of tones in the image: the horizontal axis
corresponds to pixel brightness, with dark tones to the left and
bright tones to the right, while the vertical axis shows the
number of pixels of each brightness in the image. The MSV-01
histogram is for use only as a guide and may differ from those
displayed in imaging applications or on a camera.
** The displayed items depend on the camera used for shooting.
16
Taking a Closer Look: Playback Zoom
Press
to zoom in on a still image displayed in full-screen playback (
14, 18). To increase zoom,
press
(Right button).
Three steps of zoom are available (x2, x4, x8).
Zoom is not available for RAW, TIFF or movie files.
Zoom is not available when an image is displayed with superimposed Shooting Data 1, Shooting
Data 2 or Histogram (
16).
While the image is zoomed-in, a zoom-in
icon and zoom ratio are displayed in the top left
corner of the monitor.
Press
View other areas of
the picture
Description
Use
,
,
or
to scroll to areas of the image
not visible in the monitor.
Zoom increases each time button is pressed.
Zoom in (JPEG only)
(Right button)
Zoom out
Zoom decreases each time the button is pressed.
(Left button)
Return to full-screen
mode
Cancel zoom and return to full-screen display.
To view other pictures, first cancel zoom, then select another image using the multi selector.
Viewing Images Stored on a Memory Card (Play CF card images)
Select Play CF card images from the main menu to view images stored in a memory card.
1
Insert a memory card into the memory card slot (
2
12), and turn the MSV-01 on.
3
Highlight Play CF card images using
or
.
Press
to display the thumbnails of the
folders stored on the memory card. Using
,
,
or
, highlight the DCIM
folder. The name of the currently selected
folder is displayed bottom-left.
17
Basic Operation—Taking a Closer Look: Playback Zoom
To
4
5
Press
to display thumbnails of folders containing images. Using
,
,
or
select a folder.
Basic Operation—Viewing Images Stored on a Memory Card (Play CF card images)
6
Press
to display thumbnails of the
images stored in the folder.
7
Select an image to play full-screen, moving
the cursor (a yellow frame) with
,
,
or
on the multi selector.
• The file name of the currently selected
image is displayed bottom left.
Press
to view the image in full-screen
playback.
To display the next or previous image, press
or
.
8
Press
(Left button) to return to thumbnail playback (Step 6). Press MENU (Left button) to return to the
main menu.
Image Data Supported for Playback
For supported image data formats see "Image Data Supported for Playback" (
Operations during Playback
For button operations available during playback, see pg.20-22.
18
15).
Button Operations (List View and Image Playback)
You can use the following button operations in the list view, thumbnail playback and full-screen
playback modes.
List View
Highlight Play HDD images (
14) from the main menu and press
to display a list of folders
stored on the MSV-01 hard disk drive. The following operations are available in the list view
mode.
To
Press
Description
Highlight folders
Press
or
folders.
Open a folder
Open a selected folder to list up sub-folders inside it.
sub-folders are displayed up to the sixth level.
Close a folder
Close a list of sub-folders inside the selected folder.
Display thumbnails
Display sub-folders or images in a selected folder in
the thumbnail playback mode.
Go to the EDIT menu
EDIT
(Right button)
Go to the main menu
MENU
(Left button)
on the multi selector to highlight
Go to the EDIT menu to edit the selected folder
(
23).
Return to the main menu.
19
Basic Operation—Button Operations (List View and Image Playback)
Play HDD images
Thumbnail Playback
The following operations are available in the thumbnail view displayed after selecting Play HDD
images (
14) or Play CF card images (
17).
Basic Operation—Button Operations (List View and Image Playback)
Play HDD images
To
Play CF card images
Press
Highlight images and
sub-folders
Press
,
images.
View the highlighted
image full-screen or
display the thumbnails
of the contents in the
highlighted sub-folder
Go to the EDIT menu
Description
,
or
to highlight sub-folders or
Select an image and press
lighted image full screen.
Select a sub-folder and press
to display the thumbnails of the contents in the highlighted sub-folder.
EDIT
(Right button)
Go to the EDIT menu to edit the selected folder or
image file (
23).
Return to the LIST screen
(Play HDD images)
LIST
(Left button)
Return to the LIST screen.
Return to the main menu
(Play CF card images)
MENU
(Left button)
Return to the main menu.
20
to view the high-
Full-Screen Playback
The following operations are available in the full-screen view displayed after selecting Play HDD
images (
14) or Play CF card images (
17).
To
Press
Description
View next image
Press
to view the next image.
View previous image
Press
to view the previous image.
Cycle through image
information displayed
Press
to cycle through image information.
Shooting information and histogram will be
displayed (
16).
Press
to play back a voice memo, when
(a voice
memo icon) appears for the currently displayed image.✽
Play/Pause voice memo
Press
to pause the voice memo playback.
Play back a movie (for
movies only)
Press
to play back a movie, when
(a movie icon)
appears for the currently displayed image (
22).
Zoom in (for still images
only)
to zoom in on a still image displayed in fullPress
screen playback (
17). Press
to cancel zoom for
a currently zoomed-in image.
Rotate an image
In full-screen playback, press the Rotate button on
the remote control unit to rotate an image 90º
counter-clockwise (
6, 15).
Go to EDIT menu
Go to thumbnail playback
(Remote
control unit)
EDIT
(Right button)
(Left button)
Go to the EDIT menu to edit the displayed image
(
23).
Return to thumbnail playback.
✽ To hear sound during voice memo or movie playback, connect the MSV-01 to a television or VCR using
the attached audio/video cable.
For more information on connecting to a television, see “Viewing Pictures on TV” (
35).
21
Basic Operation—Button Operations (List View and Image Playback)
Play HDD images/Play CF card images
Movie Playback
You can play back a movie file displayed in full-screen playback mode, which can be accessed from
the main menu using Play HDD images (
14) or Play CF card images (
17).
Movies are indicated by
and can be viewed by pressing
available during movie playback.
. The following operations are
Basic Operation—Button Operations (List View and Image Playback)
During playback
To
Press
Description
Start/
Pause/
Resume movie
playback
Press
to start playback. While playback is in
progress, press
to pause playback. Press
again
to resume. When the movie ends, first frame of the
movie will be displayed.✽
Fast forward/
Advance movie one
frame during pause
Press and hold
to fast-forward through the
movie. When the movie is paused, press
to
advance the movie one frame.
Rewind/
Rewind movie one
frame during pause
Press and hold
to rewind the movie. When the
movie is paused, press
to rewind the movie one
frame back.
Quit movie playback
(Left button)
Press to quit movie playback.
✽ To hear sound during movie playback, connect the MSV-01 to a television or VCR using the attached
audio/video cable.
For more information on connecting to a television, see “Viewing Pictures on TV” (
35).
✽ The MSV-01 supports movies bigger than "Small size 320" and smaller than "TV movie 640" captured
at up to 15 frames per second, and "Small size 320" or smaller size movies captured at up to 30
frames per second.
22
Organizing Images
The EDIT Menu
Using the items from the EDIT menu , which can be accessed from Play HDD images or Play CF
card images, you can perform the following operations for a selected image file or folder.
Item
Description
Delete the selected image file or folder.
24
Move
Move the selected image file or folder to a new destination inside the MSV-01 HDD.
25
Copy
Copy the selected image file or folder to a different
destination folder inside the MSV-01 HDD.
26
New folder
Create a new folder.
27
Rename
Rename an existing image file or folder.
28
Search
Search for image files created within a specified range of dates.
28
BACK (Right button)
Go back to the previous step (list view, thumbnail or fullscreen playback).
–
Organizing Images—The EDIT Menu
Delete
Displaying the EDIT Menu
Select the Play HDD images or Play CF
card images options from the main menu.
In the list view (Play
HDD images),
thumbnails or fullscreen playback
mode, select an
image file or a folder
for editing.
Press EDIT (Right button). The EDIT menu will be displayed.
Notes on Editing
• Image files or folders edited using the MSV-01 may not be displayed correctly on your camera.
• The root folder
cannot be deleted, moved, copied or renamed.
23
Delete
Use this option to delete an image file or folder selected in list view or thumbnail playback.
If a folder is selected, all data inside the folder including images will be deleted.
1
2
Press EDIT (Right button) to display the
EDIT menu (
23), then using
or
highlight Delete.
Press
. A confirmation screen will be
displayed.
Organizing Images—The EDIT Menu
3
Using
Press
or
select Yes to delete a file or folder, No to exit without deleting.
to execute the selected option and return to the list view or playback screen.
Press CANCEL (Left button) in the DELETE confirmation screen to abort the operation.
Before Deletion
• Once deleted, images cannot be recovered. The Delete operation also deletes images protected with
the camera.
• Be sure that any pictures you would like to keep have been transferred to another storage device or
computer.
24
Move
Use this option to move an image file or folder selected in list view or thumbnail playback, or the
currently displayed image to a new destination inside the MSV-01.
1
2
Press EDIT (Right button) to display the
EDIT menu (
23), then using
or
highlight Move.
Press
. A list of the stored folders will
appear. Using
,
,
or
select a
destination folder.
3
Press
. A confirmation screen will be
displayed.
highlight Yes or No.
Using
or
Press
option.
to execute the highlighted
Press CANCEL (Left button) to abort the
operation.
After completing the operation the screen
will return to the list, thumbnail or fullscreen playback view of the source
location. When in the full-screen playback
mode, an image next after the moved one
will be displayed.
"SAME FILE NAME EXISTS. OVERWRITE?"
will appear, if a file with the same name
already exists in the destination folder.
Overwriting will delete the existing file in
the destination folder. Deleted files cannot
be recovered.
• To overwrite the existing file, using
highlight Yes and press
.
• To cancel overwriting, highlight No and
press
or press BACK (Right button).
Then select a different destination folder
or change the existing file name using
Rename.
25
Organizing Images—The EDIT Menu
• To move to the root level, select the root
folder
at the top of the list.
Copy
Use this option to copy an image file or folder selected in list view or thumbnail playback, or the
currently displayed image to a different destination folder inside the MSV-01.
1
2
Press EDIT (Right button) to display the
EDIT menu (
23), then using
or
highlight Copy.
Press
. A list of the stored folders will
appear. Using
,
,
or
select a
destination folder.
Organizing Images—The EDIT Menu
• To copy to the root level, select the root
folder
at the top of the list.
3
Press
. A confirmation screen will be
displayed.
Using
Press
option.
or
highlight Yes or No.
to execute the highlighted
Press CANCEL (Left button) to abort the
operation.
After completing the operation the screen
will return to the list, thumbnail or full-screen
playback view of the source location.
"SAME FILE NAME EXISTS. OVERWRITE?"
will appear, if a file with the same name
already exists in the copy destination
folder. Overwriting will delete the existing
file in the destination folder. Deleted files
cannot be recovered.
• To overwrite the existing file, using
highlight Yes and press
.
• To cancel overwriting, select No and
press
or press BACK (Right button).
Then select a different destination folder
or change the existing file name using
Rename.
Copying from a Memory Card to the MSV-01 HDD
Use Copy CF card ➡ HDD (
13) to copy all image files stored in the memory card to the MSV-01.
Delete images that you do not need using the Delete option from the EDIT menu (
24).
Copying Images from the MSV-01 HDD to a Memory Card
Use Copy HDD ➡ CF card (
26
36) to copy image files stored on the MSV-01 to a memory card.
New folder
Use this option to create and name a new folder in the selected folder.
1
2
Press EDIT (Right button) to display the
EDIT menu (
23), then using
or
highlight New folder.
• To create a new folder at the root level,
select the root folder
at the top of
the list.
• If an image file is selected, the new
folder will be created at the same level
as the currently selected file.
Input a name following the instructions
provided in the "Name Input Screen Operations" section below.
After entering the folder name, press OK
(Right button). The new folder will be created and the monitor will return to the list
view or playback display.
• Press CANCEL (Left button) to cancel the
operation.
• File or folder names cannot begin with a
space or period.
Name Input Screen Operations
To enter a character, highlight the required key using
,
,
,
and
press
. The entered characters are displayed in the upper section of the
monitor.
• To edit the entered name, move cursor to the upper section of the screen
by pressing
repeatedly till the cursor begins flashing red. Then, move
cursor through the entered name to the desired position using
or
.
Del.
Space
Delete 1 character.
Enter single space.
Shift
Select Shift and press
and lower case letters.
to shift alphabet input between capital
Caps
Select Caps and press
to lock alphabet input to capital let-
ters. Select Caps and press
input.
again to unlock capital letter
Press
to move cursor left to a desired position in the name
you input.
Press
to move cursor right to a desired position in the name
you input.
27
Organizing Images—The EDIT Menu
• If a folder is selected, the new folder will
be created inside the selected folder.
Press
. The folder name input screen
will be displayed.
Rename
Use this option to rename a selected image file or folder.
1
2
Press EDIT (Right button) to display the
EDIT menu (
23), then using
or
highlight Rename.
Press
. The name input screen will be
displayed.
Organizing Images—The EDIT Menu
Edit the name following the instructions
provided in the "Name Input Screen Operations" section (
27).
After you have edited the name, press OK
(Right button). The folder will be renamed
and the monitor will return to the list view
or playback display.
• Press CANCEL (Left button) to cancel the
operation.
• When inputting the name, do not input
the file extension letters. The file extension will be added to the entered name
automatically.
• File or folder names cannot begin with a
space or period.
Search
Use this option to search for image files created within a specified range of dates inside the
selected folder or inside the folder containing the selected image file.
1
2
Press EDIT (Right button) to display the
or
EDIT menu (
23), then using
highlight Search.
Press
. The SEARCH menu will be
displayed.
• Highlight New and press
. An input
screen will be displayed allowing to
specify a range of dates.
• Select View previous result and press
to view the previous search results.
28
New Search
Using this option you can search for image files created within a specified range of dates (usually,
shooting date).
Set the start date (first line in the displayed screen) and the end date (second line in the displayed
screen) for the search.
To
Press
Description
Select year, month and day.
Move cursor
Move cursor.
Start searching
After selecting the end date, press
Cancel
CANCEL (Left button)
to start searching.
Cancel searching.
1. Select a year of the start date using
or
.
2. Move cursor to the month field for the start date using
.
3. Follow step 1 to select a month for the start date.
Follow step 2 to move to the day of the start date field, and continue until the end date is selected.
4. Press
to start searching.
5. Search results are shown in contact sheets of six thumbnail images.
Browse through thumbnails and highlight a required image using the multi selector.
The search results can display a maximum of 400 image files. When there are 401 or more
images, only 400 will be displayed.
6. Press
to view image in full-screen playback.
To return to the SEARCH RESULT, press
(Left button).
View previous result
Select View previous result from the SEARCH menu using
or
, and press
ous search results (in contact sheets of six thumbnail images) will be displayed.
. The previ-
Displaying Search Results
• To ensure that the file creation dates reflect the dates, on which your pictures are taken, make sure
that your digital camera clock is set correctly.
• It may take time till the search results are displayed when there are many image files in the selected folder.
• Previous search results cannot be displayed if the MSV-01 HDD or memory card has been formatted.
• Previous search results for images stored on a memory card cannot be displayed if the card has been removed.
29
Organizing Images—The EDIT Menu
Enter date
Saving Images to a Computer
Connect your MSV-01 to a computer to copy and save data stored on the MSV-01 to the computer.
When connected to a computer using the provided USB interface cable UC-E9, the MSV-01 works
as an external hard disk drive.
In addition, the MSV-01 functions as a memory card reader (
33).
The MSV-01 supports the following operating systems:
Windows XP Home Edition/Professional, Windows 2000, Windows Millennium Edition (ME),
Windows 98 Second Edition (SE),
Mac OS 9 (9.1 - 9.2), Mac OS X (10.1.2 or later).
For more information on system requirements, see "Specifications" (
66).
Using the MSV-01 with Windows 98 SE
To use the MSV-01 with Windows 98 SE, you must first install the MSV-01 USB drivers. Complete
the following procedure to install the software before connecting the MSV-01 to the computer.
Using the MSV-01 with Other Operation Systems
You do not have to install the MSV-01 USB Drivers. Continue on to "Connecting the USB Cable"
(
32).
Driver Software Installation (Windows 98 Second Edition Only)
Saving Images to a Computer
Before Installing MSV-01 USB Drivers
•
Turn off any virus-checking software.
•
Exit all other applications that may be running.
1
Turn on and start up the computer. Then insert
the MSV-01 Windows® 98 SE Driver Installer CD
into the CD-ROM drive. The Installer Language
dialog will appear automatically.
Select English and click OK.
If the Installer Language dialog is not displayed
2
30
Double-click the My Computer icon on the desktop
and double-click the CD (COOLWALKER) icon in the
My Computer window.
The Nikon COOLWALKER MSV-01 USB
Drivers Setup Wizard will start up. Read
thoroughly the provided explanation, and then
click Next.
3
The destination folder for Nikon COOLWALKER
MSV-01 USB Drivers will be displayed under
"Destination Folder." Click Install to begin the
installation.
•
4
Click Finish to complete the Nikon COOLWALKER MSV-01 USB Drivers installation.
When the installation has completed, remove
the MSV-01 Windows® 98 SE Driver Installer CD
from the CD-ROM drive.
Uninstalling the Nikon COOLWALKER MSV-01 USB Drivers (Windows 98 Second Edition Only)
Note: Before uninstalling the software, disconnect the MSV-01 from the computer (
34).
1. To uninstall the Nikon COOLWALKER MSV-01 USB Drivers, click Programs in Windows Start
menu and select Uninstall USB driver from the Nikon COOLWALKER MSV-01 program
group.
2. The uninstaller will start up. Follow the on-screen instructions to complete uninstallation.
31
Saving Images to a Computer
5
To change the installation destination, click
Browse (by default, the destination location is set
to C\Program Files\Nikon COOLWALKER MSV-01).
Connecting the USB Cable
Turn the computer on and wait for the operating system to start up. Turn the MSV-01 off and connect it to your computer as shown below using the provided USB cable UC-E9.
Saving Images to a Computer—Connecting the USB Cable
Notes on Connecting to a Computer
•
•
•
•
Place the MSV-01 on a flat and stable surface.
When connecting the MSV-01 to a computer, use the DSA-0151F-05 AC adapter.
Connect the MSV-01 directly to the computer; do not connect the cable via a USB hub or keyboard.
When the MSV-01 is connected to a computer, "Connecting via USB" is displayed on the monitor;
all controls are disabled.
• When disconnecting the MSV-01 from a computer, disconnect the USB cable only after completing
the procedure described in "Disconnecting the COOLWALKER MSV-01" (
34).
32
Copying Images to the Computer
1. To copy data stored on the MSV-01 HDD to the computer, make sure that no memory card is
inserted in the MSV-01, then turn the MSV-01 on.
The monitor of the MSV-01 will indicate that the unit is connected using USB interface, and
your computer will recognize the MSV-01 as a Mass Storage device.
2. Copy images from the MSV-01 to your computer using computer operations.
•
In Windows XP and Mac OS X, depending on the system settings, the image files on the MSV-01
HDD will be automatically detected and a message will appear prompting to start an image
related application.
•
For more information on copying and other operations with an external hard-disk drive, refer
to the user's manuals or help for your computer or applications.
Windows
Open the "COOLWALKER" icon representing the MSV-01 from My Computer and copy files and
folders stored on the MSV-01 to your computer, using a simple copy-and-paste operation.
Open the "COOLWALKER" icon representing the MSV-01 displayed on the desktop and copy files
and folders stored on the MSV-01 to your computer, using a simple copy-and-paste operation.
Using the COOLWALKER MSV-01 as a Card Reader
• When the MSV-01 is turned on with a memory card inserted, it functions as a card reader.
• When the MSV-01 is connected as a card reader, the drive name (disk volume icon) representing the
MSV-01 depends on the device used for formatting the memory card.
• Before removing a memory card, be sure to disconnect the MSV-01 from the computer using the procedure described in the next section, "Disconnecting the COOLWALKER MSV-01" (
34) and turn
the MSV-01 off.
33
Saving Images to a Computer—Copying Images to the Computer
Macintosh
Disconnecting the COOLWALKER MSV-01
Be sure to remove the MSV-01 from the system as shown below before disconnecting the USB
cable and turning the MSV-01 off.
Windows XP Home Edition/Professional
Click the "Safely Remove Hardware" icon in the task bar and select
Safely remove USB Mass Storage Device from the menu that
appears.
Windows 2000 Professional
Click the "Unplug or Eject Hardware" icon in the task bar and select Stop
USB Mass Storage Device from the menu that appears.
Saving Images to a Computer—Disconnecting the COOLWALKER MSV-01
Windows Millennium Edition (Me)
Click the "Unplug or Eject Hardware" icon in the task bar and select Stop
USB Disk Drive from the menu that appears.
Windows 98 Second Edition (SE)
In the My Computer window, click with the right mouse button on the
COOLWALKER icon corresponding to the MSV-01 and select Eject from
the menu that appears.*
Mac OS X
Mac OS 9
Drag the "COOLWALKER" disk
volume icon into the Trash.*
Drag the "COOLWALKER" disk
volume icon into the Trash.*
* When the MSV-01 is connected as a card reader, the drive name (disk volume icon) representing
the MSV-01 depends on the device used for formatting the memory card.
34
Advanced Operation
Viewing Pictures on TV
The supplied EG-CW1 audio/video (A/V) cable can be used to connect the MSV-01 to a television
or VCR.
Choosing a Video Mode
The Video mode option in the MSV-01 SET UP menu offers a choice of NTSC and PAL standards
(
54). Be sure that the selected mode matches the standard used in the video device.
1
2
Turn the MSV-01 off
Turn the MSV-01 off before connecting or disconnecting the A/V cable.
Connect the A/V cable
Open the interface cover and insert the black plug of
the supplied A/V cable into the audio/video-out interface connector of the MSV-01.
Insert the yellow plug into the video-in jack and the
white plug into the audio-in jack on the television or
VCR.
4
Advanced Operation—Viewing Pictures on TV
3
Tune the television or VCR to the video
channel or external input
If in doubt, consult the documentation for your television or VCR.
Turn the MSV-01 on
The MSV-01 monitor will remain off and the television
will display the menu normally shown in the monitor.
Operate the remote control unit pointing it at the
remote control sensor located beside the memory
card slot of the MSV-01 main unit.
When Connected to a Television
Accidental disconnection of the A/V cable or AC adapter while the MSV-01 is turned on may damage the device.
Place the main unit on a flat and stable surface and be careful not to accidentally disconnect the cables.
35
Copying Images to a Memory Card (Copy HDD ➡ CF card)
Use this option to copy images that are stored on the MSV- 01 hard disk drive (HDD) onto the
memory card. You can copy selected image files or all images in a selected folder.
Copying All Images in a Selected Folder
1
Turn the MSV-01 off. Insert a memory card (
2
12) into the memory card slot and turn the MSV-01 on.
3
Using
or
, highlight Copy HDD ➡
CF card from the main menu.
Advanced Operation—Copying Images to a Memory Card (Copy HDD ➡ CF card)
4
Press
. A list of the folders stored on the
MSV-01 HDD will appear, allowing to select
a folder or an image you want to copy.
5
From the displayed list, using
,
,
or
select a folder you want to copy
from, and press COPY (Right button).
6
7
Press
. A confirmation screen will be
displayed.
• Using
Step 5.
or
, select No to return to
• Press CANCEL (Left button) to cancel the
operation and return to the main menu.
36
A list of the folders stored on the memory
card will appear. Using
,
,
or
navigate through the list to the copy
destination folder.
Press
to begin copying.
When copying is complete, "Copy
finished" will be displayed. Press
return to the main menu.
to
Copying a Selected Image
1
2
In Step 4 on page 36, from the displayed
list, using
,
,
or
, select the
sub-folder inside the DCIM folder that contains the image you want to copy.
Press
to display the contents of the
selected folder in the thumbnail playback
mode.
Using
,
,
or
select a thumbnail of an image you want to copy.
• To return to Step 1, press LIST (Left button).
3
4
A list of the folders stored on the memory
card will appear. Using
,
,
or
navigate through the list to the copy destination folder.
Press
(Left button) to return to the
thumbnail display.
5
6
Press
. A confirmation screen will be
displayed.
• Using
Step 4.
or
, select No to return to
Press
to begin copying.
When copying is complete, "Copy
finished" will be displayed. Press
return to the main menu.
to
• Press CANCEL (Left button) to cancel the
operation and return to the main menu.
Copying Images
•
•
•
•
Do not expose the device to shocks or vibration during copy operation.
Do not remove the memory card or disconnect the AC adapter during copy operation.
Digital cameras may not be able to play images copied from the MSV-01 onto a memory card.
When, during copying, the data copied exceeds the available free space on the memory card, copying
stops and "CARD FULL. COPY HAS NOT COMPLETED." is displayed. Check the available free space
on the INFORMATION screen (
56). A larger free space than the file size is required for copying.
37
Advanced Operation—Copying Images to a Memory Card (Copy HDD ➡ CF card)
Press
to confirm the selected image in
full-screen playback. Press COPY (Right
button) to finalize your selection.
Printing Pictures
Images taken with a Nikon digital camera can be printed without using a computer.
Highlight Print from the main menu and press
to display the PRINT menu.
The PRINT menu contains the following items:
Item
DPOF printset
(JPEG images only)
Description
Create a digital print order with a standard of Digital Print
Order Format (DPOF) for images in the memory card, setting
number of prints and other options.
39
Advanced Operation—Printing Pictures
To print the pictures, take the memory card to a digital print
service center or insert the memory card into a card slot of a
personal photo printer that supports DPOF.
Direct print
(JPEG images only)
Using the USB cable, connect the MSV-01 to a PictBridge compatible printer and print pictures directly from the MSV-01 or
memory cards.
42
DPOF printset
The MSV-01 supports DPOF print settings for pictures on a CF Card taken with a Nikon digital camera,
provided they have not been edited with a device other than the camera.
Files and folders with Direct Printing
When intending to print pictures using Direct Print, do not alter file or folder names except with a Nikon
digital camera, or change the destination folder for saving images as this may prevent correct
operation.
DPOF
Digital Print Order Format (DPOF) is an industry-wide standard that allows pictures to be printed from print
orders stored on the memory card. Before printing, check that the printer or print service supports DPOF.
PictBridge
PictBridge is an industry standard that enables direct printing from a digital USB device without the need to
use a computer and ensures compatibility across digital USB devices and printers produced by different
makers.
38
DPOF printset
The DPOF printset option from the PRINT menu is used to create digital "print orders" for
images stored on the memory card. It allows to select images for printing, set number of prints,
date and shooting information imprinting.
Insert a memory card into the MSV-01 before turning it on (
1
12).
2
Turn the MSV-01 on and highlight Print
using
or
.
Press
to display the Print menu.
Highlight DPOF printset using
or
.
• To return to the main menu, press
MENU (Left button).
3
4
Highlight Select images using
to display the DPOF PRINTSET
or
.
• To return to the PRINT menu, press
CANCEL (Left button).
5
6
Press
to display selection screen.
Using
or
, scroll through images. The
currently selected image is shown in the
lower section of the monitor.
39
Advanced Operation—DPOF printset
Press
menu.
7
8
Press
(+) to select the current image
and set number of prints to 1.
Use
or
to specify the number of
prints (up to 9).
• Press CANCEL (Left button) to cancel
settings made in Steps 6 to 7.
• To deselect an image, press
the number of prints is 1.
when
• Repeat Steps 6 to 8 to select additional
images.
9
10
Advanced Operation—DPOF printset
Press SET (Right button) to complete selecting images and display menu of print
options.
• To print the date of recording on all pictures in the print order, highlight Date
and press
. ON will be indicated for
the Date setting.
Press SET (Right button) to complete setting print order.
Turn the MSV-01 off and remove the memory card.
• To finish without setting print order,
press CANCEL (Left button).
• To print shutter speed and aperture on
all pictures in the print order, highlight
Shooting info. and press
. ON will
be indicated for the Shooting info. setting.
• To turn an item off, highlight the
required item and press
.
Printing Dates
If Date is ON, the date of recording will appear on pictures printed only on devices that support the
DPOF date function (the printing position depends on the printer).
The printed date is the date set on the camera during shooting. The date printed on pictures cannot be
changed.
The Print-Order Icon
During full-screen playback, a print-order icon
40
appears on images in the current print order.
All images (Setting all images for DPOF printing)
1. To print one copy of each image on the memory card, select All images from the DPOF
PRINTSET menu in Step 4 (
39).
2. Select the date and shooting information print options performing Steps 9 to 10 (
complete your digital print order.
40) to
Reset printorder
To reset any DPOF print order on the memory card, select Reset printorder from the DPOF
PRINTSET menu in Step 4 (
39).
In a confirmation screen displayed, select Yes and press
to reset.
•
To exit without resetting the print order, press CANCEL (Left button).
•
To return to the DPOF printset menu, select No and press
.
Advanced Operation—DPOF printset
41
Printing Via Direct USB Connection (PictBridge)
Use the supplied UC-E9 USB cable to connect the MSV-01 to a printer that supports PictBridge and
print images (JPEG format) stored on the MSV-01 HDD or in a memory card directly from the MSV01, without connecting it to a computer.
To print images stored on a memory card, insert the memory card into the MSV-01 before turning it on.
When using the battery pack, you are advised to select a longer period of time for the Auto power
54) so that the MSV-01 does not turn off before the USB cable is connected.
off function (
When the USB cable is connected to the MSV-01, the Auto power off function is disabled.
Connecting to a Printer
1
2
Advanced Operation—Printing Via Direct USB Connection (PictBridge)
Highlight Print from the main menu and
38).
press
to display the PRINT menu (
Press
. "Connect to printer" will be
displayed.
Highlight Direct print using
• To return to the PRINT menu, press CANCEL.
or
.
3
While "Connect to printer" is displayed on the monitor, connect the MSV-01 to a printer using the
provided UC-E9 USB cable, as shown above.
4
Turn the printer on. When the connection
is established, the direct print menu is displayed on the monitor.
Highlight DPOF print, Print CF card images
or
.
or Print images in HDD using
Item
Description
DPOF print
Print images on a memory card set for printing using
DPOF printset function (
39).
Print CF card images
Select and print images stored on a memory card.
45
Print images in HDD
Select and print images stored on the MSV-01.
43
42
46
Before Starting Direct Printing
• Check if your printer supports direct printing via direct USB connection (PictBridge).
• Before beginning direct printing, confirm your printer settings. For information on setting the
printer, refer to your printer documentation.
Power Supply Source
When printing via direct USB connection, use the provided DSA-0151-05 AC adapter to maintain
continuous stable power supply.
If using the battery pack, make sure it is sufficiently charged.
Connecting and Disconnecting the USB Cable
• Do not connect the USB cable until "Connect to printer" is displayed on the monitor.
• Disconnect the USB cable only when "Disconnect printer" is displayed on the monitor after you
have pressed DONE (Left button) in the direct print menu.
If an Error Message is Displayed
If an error message is displayed during printing (
63), check your printer connection and settings.
After solving the problem that caused the error, press CONT. (Right button) to resume printing.
To abort printing, press CANCEL (Left button).
Printing Images Stored on the MSV-01
2
Highlight Print images in HDD from the
direct print menu (
42) using
or
.
Press
to display the list view. Select a
folder containing images for printing.
• Use
or
to highlight a folder.
• Use
to display a list of sub-folders
inside the selected folder. Use
to close
the list view of sub-folders.
• To return to Step 1, press CANCEL (Left
button).
3
4
Press
to go to the SELECT PRINT
or
to scroll
IMAGES screen. Use
through thumbnails of images shown in
the top section of the monitor. The currently selected image is shown in the lower
section of the monitor.
Press
(+) to select the current image for
printing.
• The set number of prints is displayed on
the selected images.
• To return to Step 2, press LIST (Left
button).
43
Advanced Operation—Printing Via Direct USB Connection (PictBridge)
1
5
Set a number of prints for the selected
image.
• Use
(+) or
(-) to specify the
number of prints (up to 9).
• To deselect an image, press
(-) when
the number of prints for the image is 1.
• Repeat Steps 3 to 5 to select additional
images.
6
Advanced Operation—Printing Via Direct USB Connection (PictBridge)
Press SET (Right button) in Step 5 to view thumbnails of the selected images.
• Using
,
,
your selection.
or
, browse through selected images in the confirmation screen to check
• After confirming your selection, press PRINT (Right button) to start printing.
• To change the selection of images while in the confirmation screen, press BACK (Left button).
• To abort printing after it has begun, press CANCEL (Left button).
7
When printing is complete, "Print finished" is displayed briefly, and then the monitor returns to
the direct print menu.
To quit direct printing, see "Finishing Direct Printing" (
44
47).
Printing Images Stored on a Memory Card
1
2
Highlight Print CF card images from the
direct print menu (
42) using
or
.
3
Press
to go to the SELECT PRINT
IMAGES screen. Use
or
to scroll
through thumbnails of images shown in
the top section of the monitor. The currently selected image is shown in the lower
section of the monitor.
• To return to Step 1, press CANCEL (Left
button).
4
• The set number of prints is displayed on
the selected images.
• To deselect an image, press
the number of prints is 1.
(-) when
• Repeat Steps 2 to 4 to select additional
images.
5
6
Press SET (Right button) in Step 4 to view
thumbnails of the selected images.
• Using
,
,
or
, browse
through selected images in the confirmation screen to check your selection.
• After confirming your selection, press
PRINT (Right button) to start printing.
• To change the selection of images while
in the confirmation screen, press BACK
(Left button).
• To abort printing after it has begun,
press CANCEL (Left button).
When printing is complete, "Print
finished" is displayed briefly, and then the
monitor returns to the direct print menu.
To quit direct printing, see "Finishing Direct
Printing" (
47).
45
Advanced Operation—Printing Via Direct USB Connection (PictBridge)
Set a number of prints for the selected image.
• Use
(+) or
(-) to specify the
number of prints (up to 9).
Press
(+) to select the current image for
printing.
Printing Images Stored on a Memory Card Using DPOF Settings
Use the DPOF print option to print images stored on a memory card, selected using the DPOF
printset function of the MSV-01 (
39) for printing via direct USB connection.
1
2
Highlight DPOF print from the direct print
menu (
42) using
or
.
Press
to view thumbnails of the images
set for printing using the DPOF printset
function.
• Using
,
,
or
, browse
through images to confirm your selection.
• To return to Step 1, press BACK (Left button).
3
Advanced Operation—Printing Via Direct USB Connection (PictBridge)
After confirming your selection, press PRINT (Right button) to start printing.
• To abort printing after it has begun, press CANCEL (Left button).
4
When printing is complete, "Print finished" is displayed briefly, and then the monitor returns to the
direct print menu.
• To quit direct printing, see "Finishing Direct Printing" (
47).
Direct Printing using DPOF printset
• The DPOF print option in the PRINT menu is not available, when no settings have been made using
the DPOF printset function of the MSV-01 (
38) for images on the memory card, or if the
connected printer is not PictBridge/DPOF compatible.
• When printing via direct USB connection, the Shooting data will not be printed even if selected using
the DPOF printset function.
46
Finishing Direct Printing
1
2
Press DONE (Left button) in the direct print
menu.
"Disconnect printer" will be displayed.
Disconnect the USB cable.
To perform direct printing again, disconnect the USB cable and then repeat the
operation from Step 1 in "Connecting to a
Printer" (
42).
3
Advanced Operation—Printing Via Direct USB Connection (PictBridge)
When the USB cable is disconnected, the
monitor returns to the PRINT menu.
Press MENU (Left button) to return to the
main menu.
47
Slideshow
Use this option to playback images stored on the MSV-01 hard disk drive (HDD) in an automated
"slideshow" sequence at approximately 3 seconds interval (initial settings).
Highlight Slideshow from the main menu using
SLIDESHOW menu:
Menu Option
or
, and press
to display the
Description
All images in HDD
Play all images stored on the MSV-01.
48
Selected folder
Play all images in the selected folder.
49
Advanced Operation—Slideshow
Selected images
Play selected images in the order they were selected.
49
Deselect images
Clear the selection made using Selected images option.
51
Set interval
Set time interval between displayed images.
52
MENU (Left button)
Return to the main menu.
–
Playing All Images in HDD
1
2
Using
or
, highlight All images in
HDD from the SLIDESHOW menu.
Press
. The slideshow starting screen
will be displayed. Press
again to start
the slideshow.
• On operations during the slideshow
see (
51).
3
After all images have been played, the monitor returns to the slideshow start screen.
• Press MENU (Left button) to return to the main menu.
• To start the slideshow again, press
.
Viewing Images Stored on a Memory Card in a Slideshow
To playback images stored on a memory card in a slideshow, first copy images from the memory card onto
the MSV-01 hard disk (
13).
Movies
Only the first frame is displayed for movies in the slideshow mode.
48
Playing All Images in a Selected Folder
1
2
Highlight Selected folder from the
.
SLIDESHOW menu using
or
Press
. A list of folders stored on the
MSV-01 HDD will be displayed.
• Select a folder using
• Use
3
or
.
to open a list of sub-folders, and
to close the list.
4
After all images have been played, the
monitor returns to the slideshow start
screen.
• On operations during the slideshow
see (
51).
• Press MENU (Left button) to return to
the main menu.
• To start the slideshow again, press
.
Playing Selected Images
1
2
Highlight Selected images from the
SLIDESHOW menu using
or
.
Press
. A list of folders stored on the
MSV-01 HDD will be displayed.
• Select a folder using
• Use
or
.
to open a list of sub-folders, and
to close the list.
49
Advanced Operation—Slideshow
Press
. The slideshow start screen will
be displayed. Press
again to start the
slideshow.
3
4
Press
screen.
to display the SELECT IMAGES
Using
or
, scroll through images. The
currently selected image is shown in the
lower section of the monitor.
• Press LIST (Left button) to return to the
SELECT FOLDER screen.
5
6
Advanced Operation—Slideshow
To select the currently displayed image for
(ON).
playing in the slideshow, press
Press SET (Right button) to complete selection.
• To deselect the image, press
The slideshow start screen will be displayed. Press
to start the slideshow of
the selected images in the order they were
selected.
•
(OFF).
is displayed for the selected images.
• Repeat Steps 4 -5 to select additional
images.
• On operations during the slideshow
see (
51).
7
After all images have been played, the
monitor returns to the slideshow start
screen.
• Press MENU (Left button) to return to
the main menu.
• To start the slideshow again, press
.
Playback Previously Selected Images in a Slideshow
To view the slideshow of images previously selected in the SELECT IMAGES screen, highlight Selected
images from the SLIDESHOW menu, and then press SET (Right button) to display the slideshow start
screen.
To make a new selection of images, first reset the previous selection using the Deselect images option
(
51).
50
Operations During the Slideshow
When the slideshow is in progress, the following buttons are available for control.
To
Pause/
Press
Description
Press
to pause at the current slide or resume
the slideshow, if paused.
Resume
Move to the next slide
When paused, press
slide.
to move to the next
Return to the previous
slide
When paused, press
slide.
to return to the previous
Quit the slideshow
MENU
(Left button)
Quit the slideshow.
Use the Deselect images option to reset current selection of images for the slideshow set using
the Selected images option.
1
2
Using
or
images.
highlight Deselect
Press
. A confirmation dialog will be
displayed. Highlight Yes and press
to
reset the selection of images. Highlight No
and press
to exit without resetting.
51
Advanced Operation—Slideshow
Deselect images
Set interval
Use this option to set the time interval for how long each image is displayed during the slideshow.
Highlight Set interval from the SLIDESHOW menu and press
INTERVAL screen.
to display the SLIDESHOW
You can set the interval value in the range from 1 to 99 seconds. By default, the interval is set to 3
seconds.
Press
to increase the interval by one second, or
Press
to change the interval setting.
to decrease the interval by one second.
Press BACK (Left button) to abandon any change made.
Slideshow Interval
The actual slideshow interval may differ from the selected value, depending on the image file format or size.
Advanced Operation—Slideshow
52
The SET UP Menu
The SET UP menu contains the following options:
Option
Description
Brightness
Adjust monitor brightness.
Language
Choose a language for menus and messages.
Auto power off
Choose how long the MSV-01 will remain on before
turning off automatically.
54
Video mode
Set the video output mode.
54
Format (CF card/ HDD)
Format a memory card or the MSV-01 hard disk (HDD).
55
MENU (Left button)
Return to the main menu.
53
11, 54
–
Press SET UP (Left button) in the main menu to display the SET UP menu.
To display setting screens for each of the options in the SET UP menu, highlight a desired option
using
or
, and press
.
Use this option to adjust the brightness for the MSV-01 monitor. By default, Brightness is set to 8.
The striped bars in the left part of the monitor help you ensure that the full brightness range is
visible.
To
Adjust
Press
/
Set
Cancel
Description
Adjust the monitor brightness (1 to 15).
Put the new brightness setting into
effect.
CANCEL
(Left button)
Exit without changing monitor
brightness.
53
Advanced Operation—The SET UP Menu
Brightness
Language
Use this option to choose the language for menus and messages (
11).
Auto power off
Set a period of inactivity before the Auto power off function automatically turns the MSV-01 off
(
10).
By default, Auto power off is set to 1 minute.
To disable the Auto power off function, select No limit.
To
Select
Press
/
Advanced Operation—The SET UP Menu
Set
Description
Select a desired setting from thirty
seconds (30s), one minute (1m), five
minutes (5m), thirty minutes (30m), or
No limit.
Set the highlighted setting.
Cancel
CANCEL
(Left button)
Exit without any change and return to
the SET UP menu.
Connecting the AC Adapter or the USB Cable
When the AC adapter or the USB cable is connected to the MSV-01, the Auto power off function is
disabled.
Video mode
Before connecting the MSV-01 to a video device such as a television or VCR (
Video mode setting that matches the video standard used in the device.
To
Select
Press
/
35), choose a
Description
Highlight required video mode.
The MSV-01 supports NTSC and PAL
standards.
Set
Cancel
54
Set the highlighted video mode.
CANCEL
(Left button)
Exit without any change and return to
the SET UP menu.
Format (CF Card/HDD)
Use the Format option from the SET UP menu (
53) to format a memory card or the MSV-01
hard disk (HDD). Formatting memory cards or the MSV-01 HDD will delete all data they contain.
1
Highlight CF Card or HDD using
or
and press
.
• To exit without formatting press CANCEL (Left button).
2
3
• To return to Step 1, highlight No and
press
.
• To exit without formatting press CANCEL
(Left button).
Advanced Operation—The SET UP Menu
In the displayed confirmation screen highlight Format using
or
and press
.
In case of the HDD formatting, to begin
formatting, in the displayed warning
screen highlight Format using
or
and press
.
• To return to Step 1, highlight No and
press
.
4
While formatting is in progress, "Formatting..." is displayed.
When formatting is complete, "Done" is displayed briefly and the monitor returns to the SET UP
menu.
Before Formatting
• Formatting memory cards or the MSV-01 HDD will delete all data they contain, including pictures
hidden or protected with the camera and any other data that may be on the card or the MSV-01 HDD.
• Before formatting a memory card, be sure to copy any pictures you would like to keep to the MSV-01
or a computer.
• Before formatting the MSV-01 HDD, be sure to copy any pictures you would like to keep to a
computer or other storage media.
During Formatting
Do not remove the battery pack or memory card, or unplug the AC adapter while formatting is in
progress.
55
The INFORMATION Screen
Displaying Memory Information
This screen shows the remaining free memory space in, and the total capacities of, the MSV-01
internal hard disk drive (HDD) and memory cards.
Use this screen to check the memory capacity before copying new data.
To display the information, press INFO. (Right button) in the main menu.
Firmware ver.
The current firmware version of the MSV-01.
HDD Free/Total
Free space on/Total capacity of the MSV-01 hard disk drive.
CF Free/Total
Free space on/Total capacity of the inserted memory card.
Advanced Operation—The INFORMATION Screen
•
Press MENU (Right button) to return to the main menu.
Free Space Requirements
To complete copying to a memory card or internal HDD, free space larger than the size of the data being
copied is required. The data cannot be copied if it exceeds the available free space in the copy
destination.
When there is no enough free space, delete (
24) unnecessary files to create more free space.
56
Technical Notes
Optional Accessories
At the time of writing, the following optional accessories were available for the COOLWALKER MSV-01.
Contact your retailer or Nikon local representative for details.
•
Optional battery pack: EN-EL6 Rechargeable Lithium-ion Polymer Battery
Approved Memory Cards
The following cards have been tested and approved for use with the COOLWALKER MSV-01:
CompactFlash™ Memory Cards
SanDisk
Lexar Media
SDCFB
16MB, 48MB, 80MB, 96MB, 128MB, 160MB,
256MB, 512MB, 1GB
SDCFB (Type II)
192MB, 300MB
SDCF2B (Type II)
256MB
SDCFH (Ultra)
128MB, 192MB, 256MB, 384MB, 512MB, 1GB
SDCFX (Ultra II)
256MB
SDCFX
512MB, 1GB
4 x USB
16MB, 32MB, 64MB
16MB, 32MB, 48MB, 64MB, 80MB
10 x USB
160MB
12 x USB
64MB, 128MB, 192MB, 256MB, 512MB
16 x USB
192MB, 256MB, 320MB, 512MB, 640MB, 1GB
24 x USB
256MB, 512MB
24 x WA USB
256MB, 512MB
32 x WA USB
1GB
40 x WA USB
256MB, 512MB, 1GB, 2GB, 4GB
Renesas Technology
(Hitachi)
Compact FLASH
HB28 C8x
16MB, 32MB
Microdrive
DSCM
512MB, 1GB
3K4
2GB, 4GB
Technical Notes—Optional Accessories
8 x USB
Operation is not guaranteed with other makes of cards. For more details on the above cards,
please contact the manufacturer.
The latest information on memory cards approved for use with the MSV-01 can be found at the
Nikon websites (
vi).
57
Caring for Your COOLWALKER MSV-01
To ensure continued enjoyment of your Nikon product, observe the following precautions when
storing or using the device:
Cautions
This product is a high-precision device
containing internal hard disk. It
requires careful handling.
Damage to the hard disk will not only require
high repair expenses, but can also cause
corruption or irreversible loss of the stored
data.
• Do not subject to strong shocks or impacts.
Be careful not to drop or subject the device to
strong shocks, as this may cause damage to
the device and loss or corruption of the data
stored on the hard disk.
• Use the device on stable flat surfaces, such as
on a flat table, taking care not to drop the
device or memory cards. Be especially careful
when inserting or removing memory cards.
Technical Notes—Caring for Your COOLWALKER MSV-01
• Do not expose the device to shocks or vibration during operation.
It may damage the internal hard disk and
cause corruption or loss of the data stored on
the hard disk.
• Do not remove memory cards, USB cables or
the AC adapter or turn the power off during
operation.
It may cause corruption or loss of the data
stored on the hard disk. To prevent an
accidental disconnection of the AC adapter or
USB cable, avoid carrying the product from
one place to another when the cables are
connected.
• Keep away from strong magnetic fields.
Do not use or store this device in the vicinity
of equipment that generates strong
electromagnetic radiation or magnetic fields.
Strong static charges or the magnetic fields
produced by equipment such as radio
transmitters could cause corruption or loss of
the data stored on the hard disk, or
malfunction.
• Do not use or leave the device in locations
where static electricity or interference occurs.
Static electricity or interference may cause
damage to the device, loss or corruption of
the data stored on the hard disk.
58
• Static electricity may be generated in your body
or cloths. Touch a metal doornob or another
metal object to discharge static electricity from
your body before handling the device.
Static electricity may cause damage to the
device, loss or corruption of the data stored
on the hard disk.
• When there is the possibility of thunder,
unplug all cables and the AC adapter.
Thunder may cause damage to the device, loss
or corruption of the data stored on the hard
disk. If it thunders during use, be careful not
to touch the power plug and stop using the
device till the thunderstorm stops.
• Do not use or leave the device in locations
exposed to excessive dust.
Excessive dust may cause damage to the
device, loss or corruption of the data stored
on the hard disk.
• Follow all precautions or instructions when
connecting the device to a computer.
When connecting the unit to a computer, be
careful to observe any precautions or
instructions provided by the manufacturer of
your computer or peripheral devices.
• Do not use at heights exceeding 2,500 m
(8,202 ft) above sea level.
Ensure that your data is backed up
using another recording medium
Note, that Nikon will not be held responsible
for any deletion, loss or corruption of data.
You are advised to create a backup of
important data stored on the internal hard
disk of the device using an alternative
recording medium.
Data stored on the hard-disk of this product could
be lost or damaged in the following instances:
• If the product is used incorrectly
• If the product is exposed to static or noise
• During malfunction and repair
• If the product is subject to damage caused
by natural disasters
Nikon hereby gives notice that it will not be
held liable for any damages resulting from the
loss or corruption of data in the above or any
circumstances.
Make a backup of your data if submitting this product for repair
All data stored on the hard disk may be erased
during repair.
Be sure to make a backup of the data stored
on the hard disk before submitting the device
for repair.
Be sure to remove a memory card and keep it
in a safe place.
Do not use, transport or store the
device with the battery pack removed
Failure to observe this precaution could result
in malfunctions or damage the MSV-01.
Keep dry
The device will be damaged if immersed in
water or exposed to high levels of moisture.
Do not touch the device with wet
hands
Failure to observe this precaution could result
in malfunctions or damage to the MSV-01.
Avoid sudden changes in temperature
Do not apply excessive force
Do not apply excessive force to the device,
connector, or card slot. These parts are
especially susceptible to damage.
Do not leave a card in the memory card
slot
Do not leave a card in the memory card slot
when transporting or carrying the device. It
may cause damage to the device.
When not using the card slot or cable
connector, be sure to close their covers.
Transferring ownership or disposing of
this product
• Remember that any data you have recorded
could end up being reused and distributed to
others when you transfer ownership or dispose of the unit, memory cards and other
recording media.
• Although data recorded on the internal harddisk appears to be removed by selecting
"Delete" or "Format" from the menu in the
unit's operation screen, remember that this
data may be recovered using special software
programs and other such methods.
Incorrect use of the AC adapter may
cause an electric shock, fire or damage
to the device. Be sure to read and follow safety warnings and cautions provided in the "For your safety" section
of this manual, together with the handling instructions provided below.
• When not using AC adapter, disconnect it
from the device, then unplug it from the
power outlet.
• Before connecting or removing AC adapter,
make sure that the device is turned off.
• Be sure to hold the plug body when removing
the AC adapter, do not pull the cord.
• Do not short the DC plug.
• Do not apply excessive force to the AC adapter
while it is connected to the device.
Do not carry or transport the device
while turned on
Do not insert the unit in the soft case, leave it
unattended or carry it around while turned on.
Turn the device off before removing or
disconnecting the power source
Do not unplug the product or remove the
battery pack while the product is on, or while
images are being recorded or deleted. Forcibly
cutting power in these circumstances could
result in loss of data or in damage to the hard
59
Technical Notes—Caring for Your COOLWALKER MSV-01
Sudden changes in temperature, such as occur
when entering or leaving a heated building
on a cold day, can cause condensation inside
the device. To prevent condensation, place the
device in a carrying case or a plastic bag
before exposing it to sudden changes in
temperature.
disk or internal circuitry. To prevent an
accidental interruption of power, avoid
carrying the product from one place to
another while the AC adapter is connected.
Batteries
Charge the battery pack of the main unit before using.
• Rechargeable Lithium-ion Polymer Battery
EN-EL6 is used as the main unit battery pack.
• Connect the AC adapter and charge the
rechargeable battery pack before using the
device. The supplied rechargeable battery
pack is only partially charged and needs
recharging before using it for the first time.
• After long periods during which the battery
pack has not been used, the battery pack
should be charged before using it.
• When recharging, ambient temperature should
be in the vicinity of 5°C to 35°C (41°F to 95°F)
• It is normal for batteries to warm up during
charging or use. This does not indicate a malfunction or deterioration of battery pack performance.
Important!
When storing or transporting a spare battery pack removed from the MSV-01, be
sure to place it in the supplied case to avoid
shorting the battery terminals. Failure to
observe this precaution could result in leakage, overheating, rupture, or other damage
to the battery pack.
Using batteries at low temperatures
•
On cold days, the capacity of batteries
tends to decrease. Be sure that the battery
pack is fully charged before heading outside to use in cold weather. Keep the battery pack and the equipment in a warm
place. Once warmed, a cold battery pack
may recover some of its charge.
•
At low temperatures the battery operating
time will be shorter than usual.
Battery level indication
• Confirm the battery level on the monitor after
turning the device on.
• Please note, that as a characteristic common
for all batteries, after turning power off and
on, the battery indicator may show a sufficient
level even when the battery is low.
Technical Notes—Caring for Your COOLWALKER MSV-01
Carrying a spare battery pack
• It is recommended that you carry a fullycharged spare battery pack when using the
device in locations where there is no AC
power source available. You may find it
difficult to charge the battery or to purchase
replacement battery packs at short notice. Use
only the specified Rechargeable Lithium-ion
Polymer Battery EN-EL6.
• When removing or attaching the battery pack,
always observe the correct procedure
described in this manual to avoid damaging
the battery terminals.
• Avoid touching the battery pack terminals to
prevent them from becoming dirty.
• If the battery terminals become dirty, wipe
them with a soft, dry cloth before use.
60
Used batteries are a valuable resource. Please
recycle used batteries in accordance with local
regulations.
Cleaning
Storage
Body
Turn the MSV-01 off and remove the AC
adapter when not in use.
Use a blower to remove dust and lint, then
wipe gently with a soft, dry cloth.
After using your MSV-01 at the beach or seaside, wipe off any sand or salt with a cloth
lightly dampened with fresh water, then dry
thoroughly.
LCD Monitor
Remove dust or lint with a blower. To remove
fingerprints and other stains, clean the monitor
with a soft, dry cloth, being careful not to
apply excessive pressure.
Avoid contact with liquid crystal
Should the monitor break, care should be
taken to avoid injury due to broken glass
and to prevent the liquid crystal from the
monitor touching the skin or entering the
eyes or mouth.
Do not use alcohol, thinner, or other
volatile chemicals.
Do not store the products in locations that:
•
are poorly ventilated or damp
•
are next to equipment that produces
strong electromagnetic fields, such as televisions or radios
•
are exposed to static electricity
•
are exposed to vibrations
•
are exposed to excessive moisture or
humidity
•
are exposed to risk of short circuits
•
are exposed to excessive dust
•
are exposed to temperatures below -10°C
(14°F) or above 45°C (113°F)
•
are subject to humidities of over 60%
To prevent deterioration of battery pack
performance, it is recommended that the product
be stored in dry locations with an ambient
temperature of 15 - 25°C (59-77°F).
When storing the MSV-01 for long periods, charge
the battery pack and remove the battery from the
remote control unit before putting it away.
• Images in the monitor may be difficult to see
in a bright light.
• The monitor is lit by an LED backlight. Should
the monitor begin to dim or flicker, contact
your Nikon service representative.
61
Technical Notes—Caring for Your COOLWALKER MSV-01
Notes on the LCD Monitor
• The monitor may contain a few pixels that are
always lit or that do not light. This is a characteristic common to all TFT LCD displays, and
does not indicate a malfunction.
Be sure to close the memory card slot and interface connector covers and keep the MSV-01
main unit in the provided soft case.
Error Messages
This section lists the error messages that appear on the monitor when there is a problem with the
MSV-01. Consult the list below before contacting your retailer or Nikon representative.
Display
Problem
Solution
CARD IS NOT
FORMATTED
Memory card has
not been formatted
for use in camera or
MSV-01.
Format card using your camera.
NO CARD PRESENT
MSV-01 cannot
detect memory
card.
Turn power off and confirm that
memory card is correctly inserted.
12
THIS CARD
•
57
CANNOT BE USED
•
CARD ERROR
Error accessing
memory card.
Memory card
has not been
formatted for
use in camera
or MSV-01.
–
•
Use approved memory card.
•
Check that contacts are clean. If
card is damaged, contact your
retailer or Nikon representative.
–
•
Format memory card using your
camera.
–
Technical Notes—Error Messages
LAST CARD MAY NOT
BE COPIED CORRECTLY.
Copy process
interrupted.
Repeat copy operation to try again.
13
DISK FULL. COPY HAS
NOT COMPLETED.
Insufficient space
to record data on
hard disk (HDD).
Create space by deleting files and
folders you do not need from HDD.
24
CARD FULL. COPY HAS
NOT COMPLETED.
Insufficient space
to record data on
memory card.
•
Create space by deleting files and
folders you do not need from
memory card.
24
•
Insert new memory card.
CANNOT PASTE
A FOLDER TO ITSELF.
Source and
destination folders
are same.
Choose another destination folder.
SAME FILE NAME
EXISTS. OVERWRITE?
File with same
name already
exists in
destination folder.
Overwriting will delete existing file.
Deleted files cannot be restored. If
you are not sure, press CANCEL (Left
button).
25
THE NAME CANNOT
•
Enter alphabet or numbers for a new
file or folder name.
27
BE USED.
•
62
File or folder
name contains
only space(s).
File or folder
name begins
with space or
period.
36
–
25
26
26
28
Display
Problem
NO IMAGE FILE
EXISTS.
Folder(s) selected
for playback
contain(s) no
supported images.
CANNOT DISPLAY
•
•
MSV-01 does
not support
this file
format.
Image size
exceeds
supported
dimensions.
Solution
•
•
•
Select a folder containing images
from list view or thumbnail
playback mode.
Insert memory card containing
images, or copy images to MSV-01
HDD.
The image cannot be displayed on
MSV-01. View file on computer or
camera used for shooting.
–
13
–
CARD FORMAT ERROR
Error has occurred
during formatting
memory card.
Try to format card again. If error
persists, contact your retailer or Nikon
representative.
55
HDD FORMAT ERROR
Error has occurred
during formatting
HDD.
Try to format hard disk again. If error
persists, contact your retailer or Nikon
representative.
55
UNSUPPORTED
FILE FORMAT
Your printer does
not support this
file format.
Check your printer specification and
image file format.
INK LOW
Ink low
Check printer. Press Cont. (Right
button) to continue printing
43
OUT OF INK
No ink
Check printer. For solutions see
operation manual of your printer.
–
OUT OF PAPER
Paper tray empty
Check printer. For solutions see
operation manual of your printer.
–
INCORRECT PAPER SIZE
Paper size selected
is different from
paper tray
detected
Check printer. For solutions see
operation manual of your printer.
–
PAPER JAM
Paper jam
Check printer. For solutions see
operation manual of your printer.
–
CHECK
PRINTER CONNECTION.
Printer
communication
error
Check USB cable connection. Make
sure that printer is turned on.
42
UNKNOWN PRINT ERROR
Unknown error
occurred during
printing
Check printer. For solutions see
operation manual of your printer.
–
CONNECT AC ADAPTER
AND TRY AGAIN.
No power supply
from AC adapter.
Check AC adapter connection and
repeat last operation.
–
–
When the power-on lamp blinks with red, this indicates that a charging error has occurred.
Disconnect the AC adapter from the MSV-01 and the power outlet. Clean the plugs and re-connect
the AC adapter.
If the error persists, contact your retailer or Nikon representative.
63
Technical Notes—Error Messages
When the Power-on Lamp Blinks with Red
Troubleshooting
If your MSV-01 fails to function as expected, check the list of common problems below before consulting your retailer or Nikon representative.
Refer to the page numbers listed in the right-most column for information on solving the problems listed here.
Electronically-controlled devices
In extremely rare instances, the MSV-01 may fall in unoperatable state (freeze during operation). Press the power switch to turn the MSV-01 off.
• If the MSV-01 does not go off even when you press the power switch, you may
need to reset the MSV-01.
To reset the unit, simultaneously press and hold down the power switch and right function
button for several seconds.
* Note that resetting the unit as described above may result in the loss or corruption of any data
not yet recorded to the memory card or hard disk at the time the problem occurred.
• If the problem persists, perform the following steps:
1 Disconnect the AC adapter from the MSV-01 (if connected).
2
Remove and re-attach the battery pack.
When the MSV-01 is used on battery power for an extended period, the battery pack
may become hot. Be careful to avoid burns.
3
Turn the MSV-01 on again.
In the event of continued malfunction, contact your retailer or Nikon representative. Note
that disconnecting the power source as described above may result in the loss of any data
not yet recorded to the memory card or hard disk at the time the problem occurred.
Technical Notes—Troubleshooting
Problem
LCD monitor is
blank
Possible Cause
•
•
10
8
•
•
•
The MSV-01 is off.
Battery pack is not correctly inserted or battery contacts
are covered with insulating tape.
Battery is exhausted.
AC adapter is not correctly connected.
A/V cable is connected to the MSV-01.
MSV-01 turns off
without warning
•
•
•
MSV-01 is turned off with Auto power off function.
Battery is low.
Battery is cold.
54
10
60
Monitor is hard to
read
•
•
•
Ambient lighting is too bright: move to a darker location.
Monitor brightness needs adjustment.
Monitor is dirty: clean monitor.
–
53
61
Computer does not
recognize MSV-01
•
•
•
•
•
MSV-01 is off.
AC adapter is not correctly connected.
Battery is low.
USB cable is not correctly connected.
COOLWALKER MSV-01 USB driver is not installed on computer
(Windows 98 SE only): install software from supplied CD.
10
9
10
32
30
10
9
35
If You Hear an Unusual Noise from the Main Unit
If you hear any kind of unusual rattling or grinding sound coming from the internal HDD during
operation, it is possible that its operating life is coming to end.
Create a backup of the data stored on the internal hard disk of the device using an alternative
recording medium, and contact your retailer or Nikon representative.
64
Specifications
Type
Digital Photo Storage Viewer MSV-01
Storage media
Type
2.5" internal HDD
Storage Capacity
30GB (1 KB = 1000 Bytes) *1
Type I and II CompactFlash™ memory cards; Microdrives
Monitor
2.5", 490 (H) x 240 (V) dots, TFT LCD Monitor with brightness adjustment
Display languages
(Menus)
German, English, Spanish and French
Supported file formats
Compliant with the Design rule for Camera File System (DCF) standard
formats:
JPEG, TIFF, NEF (RAW) *2,
QuickTime (MOV)*3, *4,
Wave Format Audio File (WAV)*3, *5
The product supports the above file formats recorded with Nikon Digital
cameras.
Playback modes
Thumbnail, Full-screen playback,
Zoom (JPEG images only): X2, X4, X8, Slideshow, Movie playback,
Histogram display, Shooting information display, Search by file creation
date
Video output
Can be selected from NTSC and PAL.
Interface
USB
• Mass Storage: functions as computer's external HDD or a CF card
reader
• PictBridge support: can be connected via USB to a PictBridge
standard printer
I/O terminals
Type II CompactFlash™ (CF card slot) x 1, USB (mini) x 1,
Audio/Video output x 1, DC in x 1
Power sources
•
Power consumption
Max. 9W (peak time)
Approximate Battery Life
1.5 hours (Measured at 20 °C/68 °F with fully-charged battery pack)
Dimensions (W x H x D)
Approximately 81 x 130 x 35 mm (3.2" x 5.1" x 1.4")
Weight
Approximately 300g (including battery pack)
•
Technical Notes—Specifications
Supported memory card
types
Rechargeable Lithium-ion Polymer Battery EN-EL6 (main unit
battery pack)
AC adapter DSA-0151F-05 (supplied)
Operating environment:
Temperature
5-40 °C (41-104 °F)
Humidity
10-90% (no condensation)
Altitude
Less than 2,500 m (8,202 ft) (above sea level)
65
Computer system
requirements
•
•
Set DPOF Print Order
function
Interface: built-in USB ports (The MSV-01 may not function as
expected when connected to a USB hub.)
Operating system: Windows XP Home Edition/Professional,
Windows 2000 Professional, Windows Millennium Edition (Me),
Windows 98 Second Edition (SE) *6; Mac OS 9.1 - 9.2, Mac OS X
(Version 10.1.2 or later). Only preinstalled versions are supported.
Equipped with function that allows setting DPOF Print Order for DCF
standard compliant images stored on a CF memory card (JPEG images
only).
*1: Maximum capacity. (1 KB = 1024 Bytes: 27.9 GB.)
*2: The MSV-01 supports playback of JPEG preview images within NEF (Nikon Electronic Image Format)
images recorded with Nikon digital cameras (D1X, D1H, D2H, D100, D70, COOLPIX 5000/5700/8700).
The latest information on image data supported for playback can be found at the Nikon websites
vi).
(
*3: Audio video equipment with an appropriate input required to play audio.
*4: The MSV-01 supports movies bigger than "Small size 320" and smaller than "TV movie 640" captured at up to 15 frames per second, and "Small size 320" or smaller size movies captured at up to
30 frames per second.
*5: Only voice memo attached to images using digital cameras.
*6: CD-ROM drive is required for COOLWALKER MSV-01 USB driver installation (Windows 98 SE only).
Remote Control Unit
Technical Notes—Specifications
Type
Infrared Remote Control Unit
Operating distance
Approximately 5 m (16.4 ft) (without obstacles)
Power source
3V, CR2025 Lithium Battery
Dimensions (W x H x D)
Approximately 41 x 87 x 7 mm (1.6" x 3.4" x 0.3")
Weight
Approximately 17g (without battery)
AC Adapter DSA-0151F-05 (produced by Dee Van Enterprise Co., Ltd.)
Input
AC 100-240 V, 50/60 Hz, 0.4 A
Input capacity
46 W
Output
DC +5 V, 2.8 A
Dimensions (W x H x D)
Approximately 53 x 81 x 42 mm (2.1" x 3.2" x 1.7") (excepting
protruding parts and cord)
Power cord length
Approximately 1.8 m (5.9 ft)
Weight
Approximately 197 g (including cord)
Design rule for Camera File system (DCF)
The Design Rule for Camera File System (DCF) is a standard widely used in the digital devices
industry to ensure compatibility among different makes of devices.
66
Index
Symbols
(Battery status icon), 10
(Movie icon), 16
(Print order icon), 16, 40
(Unsupported data icon), 15
(Voice memo icon), 16
(Zoom in icon), 17
A
AC adapter, 2, 9 - 10, 43, 59
See also Power switch; Power-on lamp
Access lamp, see HDD, access lamp
All images, 41
See also DPOF printset
All images in HDD, 48
APERTURE, see Image information
Audio/Video (A/V) cable, 2, 10
connecting, 35
Audio/Video-out connector, 4, 35
Auto power off (SET UP menu), 10,
53 - 54
B
C
Camera, 1
CAMERA (Camera type), see Image information
CF card, see Format
CF Free/Total, see INFORMATION screen
CompactFlash™, see Memory card
Computer, 1
connecting to, 32
copying to, 33
disconnecting from, 34
Copy (EDIT menu), 26
Copy CF card ➡ HDD, 7, 13
Copy HDD ➡ CF card, 7, 36
See also Computer, copying to; INFORMATION screen
Date, imprinting, 40
See also DPOF
DCF, 66
DC-in connector, 4, 9
See also AC adapter
Delete (EDIT menu ), 24
Deleting, 24
See also Memory card, formatting;
HDD, formatting
Deselect images, 51
See also Slideshow
Direct print, 38, 42
Direct printing (PictBridge), 42 - 47
DPOF (Digital Print Order Format), 38
DPOF print, 42, 46
DPOF printset, 38 - 39, 46
E
EDIT, 19 - 21, 23
EDIT menu, 7, 23 - 29
Enter button, 3, 5 - 6
Error messages, 62
EXP +/- (Exposure compensation), see Image information
F
FILE SIZE, see Image information
Firmware ver., see INFORMATION
screen
FOCAL LENGTH, see Image information
FOLDER TO COPY FROM, 36 - 37
FOLDER TO COPY TO, 26, 36 - 37
Format, 53, 55
See also Memory card, formatting;
HDD, formatting
Full-screen playback, see Playback
Function buttons, 3, 5 - 6
H
HDD, 58, 64
access lamp, 3
formatting, 55
HDD Free/Total, see INFORMATION
screen
HDD, see Format
Histogram, 16
See also Image information
67
Index
Battery pack, 4, 9, 57, 59 - 61
battery release button, 4, 8
case, 2
charging, 8 - 9
checking battery level, 10
insulating tape, 8
removing/installing, 8
Brightness, 53
D
I
O
Image data formats, supported, 1, 15, 22,
66
Image information, 16, 21
INFO., 7, 56
INFORMATION screen, 56
Interface connector cover, 4
Operating system (OS), 30 - 34, 66
Optional accessories, 57
J
JPEG, 15, 17, 38
See also Image data formats
L
Language, 11, 53 - 54
Left function button, see Function buttons
LIST, 15, 20, 37, 43, 50
List view, 14, 19, 24 - 26, 36, 43, 49
M
Index
Main menu (MENU), 7
Memory card, 1, 12, 42, 48, 56, 59
approved, 57
formatting, 55
inserting, 12
reader, 33
removing, 12
slot, 3, 12
slot cover, 3, 12
supported, 12
MENU, 11, 15, 18 - 20, 39, 47 - 51, 53, 56
See also Main menu
METERING, see Image information
MODE, see Image information
Monitor, 3, 61
Move (EDIT menu), 23, 25
Movie, 15 - 16, 48
See also Image data formats; Playback
Multi selector, 3, 5 - 6
N
NEF, 1, 15
See also Image data formats
New, 28
See also Search
New folder (EDIT menu), 23, 27
NEW SEARCH, 29
See also Search
NTSC, see Video mode
68
P
PAL, see Video mode
PictBridge, 1, 38, 42
Play CF card images, 7, 17, 20 - 22
Play HDD images, 7, 14, 19 - 22
Playback
full-screen, 14 - 15, 17, 18, 21
movie, 21 - 22
thumbnail, 14 - 15, 18, 20, 37
voice memo, 21
zoom, 16 - 17
Power switch, 3, 10, 64
Power-off button, see Remote control unit
Power-on lamp, 3, 10, 63
PRINT, 38 - 39, 44 - 46
Print CF card images, 42, 45
Print images in HDD, 42 - 43
PRINT menu, 38 - 47
Printer, 1
connecting to, 42
disconnecting from, 47
R
Remote control unit, 2, 5 - 6
battery, 5
battery holder, 5
insulating tape, 5
power OFF button, 5 - 6
rotate button, 5 - 6, 15, 21
transmitter, 5
Remote-control sensor, 3
Rename (EDIT menu), 23, 28
Reset printorder, 41
See also DPOF
Resetting MSV-01, 64
Right function button, see Function buttons
Rotate button, see Remote Control Unit
S
Search, 23, 28
SEARCH RESULT, 29
SELECT DEST. FOLDER, see Move
SELECT FOLDER, 43, 49
SELECT IMAGES, 50
Select images, 39
See also DPOF
SELECT PRINT IMAGES, 39 - 40, 43, 45
Selected folder (SLIDESHOW menu),
48 - 49
Selected images (SLIDESHOW menu),
49, 50
SENSITIVITY, see Image information
Set interval (SLIDESHOW menu), 52
SET UP, 7, 10, 53
SET UP menu, 53 - 55
Shooting Data, 16, 46
See also Shooting info.
Shooting info., imprinting, 40
See also DPOF
SHUTTER (Shutter speed), see Image information
Slideshow, 7, 48
SLIDESHOW INTERVAL, 52
SLIDESHOW menu, 48 - 52
Soft case, 2
T
Index
Thumbnail playback, see Playback
TV (Television), 1
connecting to, 35
U
USB, 1, 32, 38, 42, 46
cable, 2, 32, 42
connector, 4
driver software installation, 30 - 31
See also Computer; Printer
V
Video mode, 35, 53 - 54
Video output, 1
View previous result, 28 - 29
See also Search
Voice memo, 15 - 16
See also Playback
W
WHITEBAL (White balance), see Image information
69
Printed in Japan
BG4G01200201(11)
6MAW1411-A
Download PDF

advertising