Hilti DX 35 Operating Instruction

DX 35
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Bedienungsanleitung
de
Operating instructions
en
Mode d’emploi
fr
Manual de instrucciones
es
1
ꛈ
ꛉ
ꛊ
ꛋ
ꛍ
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
ꛌ
ꛎ
ꛏ
2
3
4
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
5
6
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
7
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
ORIGINAL OPERATING INSTRUCTIONS
DX 35 powder-actuated fastening tool
It is essential that the operating instructions
are read before the tool is operated for the
first time.
Always keep these operating instructions together with the tool.
Ensure that the operating instructions are
with the tool when it is given to other persons.
Contents
1 Safety instructions
2 General information
3 Description
4 Accessories, consumables
5 Technical data
6 Before use
7 Guidelines
8 Operation
9 Care and maintenance
10 Troubleshooting
11 Disposal
12 Manufacturer’s warranty - tools
13 EC declaration of conformity (original)
14 Confirmation of CIP testing
15 Health and safety of the operator
Page
17
19
20
21
22
22
22
23
24
26
30
30
31
31
31
1 These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the operating instructions.
In these operating instructions, the designation “the tool”
always refers to the DX 35 powder-actuated fastening
tool.
Parts and operating controls 1
@ Casing
; Piston guide
= Base plate
% Fastener guide
& Piston
( Spring clip
) Catch
+ Stabilizer (fragmentation guard, only USA)
1 Safety instructions
1.1 Basic information concerning safety
In addition to the information relevant to safety given
in each of the sections of these operating instructions,
the following points must be strictly observed at all
times.
1.1.1 Using cartridges
Use only Hilti cartridges or cartridges of equivalent
quality.
Use of cartridges of inferior quality in Hilti tools may lead
to a build-up of unburned powder, which may explode
and cause sever injuries to operators and bystanders.
Cartridges must fulfill one of the following minimum requirements:
a) The applicable manufacturer must be able to verify
successful testing in accordance with the EU standard EN 16264 or
b) The cartridges must bear the CE conformity mark
(mandatory in the EU as of July 2013).
NOTE
All Hilti cartridges for powder-actuated tools have been
tested successfully in accordance with EN 16264. The
tests defined in the EN 16264 standard are system tests
carried out by the certification authority using specific
combinations of cartridges and tools. The tool designation, the name of the certification authority and the system
test number are printed on the cartridge packaging.
Please refer to the packaging
www.hilti.com/dx-cartridges
example
at:
1.1.2 Requirements to be met by users
a) The tool is intended for professional use.
b) The tool may be operated, serviced and repaired
only by authorized, trained personnel. This personnel must be informed of any special hazards
that may be encountered.
1.1.3 Personal safety
a)
Stay alert, watch what you are doing and use
common sense when operating a direct fastening
tool. Don’t use the tool when you are tired or under
the influence of drugs, alcohol or medication. Stop
using the tool if you experience pain or do not feel
well. A moment of inattention while operating the
tool may result in serious personal injury.
17
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
en
en
b) Avoid unfavorable body positions. Make sure you
work from a safe stance and stay in balance at all
times.
c) Wear non-skid shoes.
d) Never point the tool toward yourself or other persons.
e) Never press the nosepiece of the tool against your
hand or against any other part of your body (or
other person’s hand or part of their body).
f) Keep other persons, especially children, away
from the area in which the work is being carried
out.
g) Keep the arms slightly bent while operating the
tool (do not straighten the arms).
h) Observe the information printed in the operating instructions concerning operation, care and maintenance.
1.1.4 Use and care of powder-actuated fastening
tools
Use the right tool for the job. Do not use the tool
for purposes for which it was not intended. Use it
only as directed and when in faultless condition.
b) Never leave a loaded tool unattended.
c) Store unused cartridges and tools currently not in
use in a dry place where they are not exposed to
high temperatures.
d) Transport and store the tool in a toolbox that can be
secured to prevent unauthorized use.
e) Always unload the tool (remove cartridges and
fasteners) before cleaning, before maintenance,
before work breaks and before storing the tool.
f) When not in use, tools must be unloaded and
stored in a dry place, locked up or out of reach of
children.
g) Check the tool and its accessories for any damage. Guards, safety devices and any slightly worn
parts must be checked carefully to ensure that
they function faultlessly and as intended. Check
that moving parts function correctly without sticking and that no parts are damaged. All parts must
be fitted correctly and fulfill all conditions necessary for correct operation of the tool. Damaged
guards, safety devices and other parts must be
repaired or replaced properly at a Hilti service
center unless otherwise indicated in the operating instructions.
h) Pull the trigger only when the tool is fully pressed
against the working surface at right angles.
i) Always hold the tool securely and at right angles
to the working surface when driving in fasteners.
This will help to prevent fasteners being deflected
by the working surface.
j) Never redrive a fastener. This may cause the
fastener to break and the tool may jam.
k) Never drive fasteners into existing holes unless
this is recommended by Hilti.
l) Always observe the application guidelines.
a)
18
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
1.1.5 Work area safety
a) Ensure that the workplace is well lit.
b) Operate the tool only in well-ventilated working
areas.
c) Do not attempt to drive fasteners into unsuitable
materials: Materials that are too hard, e.g. welded
steel and cast iron. Materials that are too soft, e.g.
wood and drywall panel (gypsum board). Materials
that are too brittle, e.g. glass and ceramic tiles.
Driving a fastener into these materials may cause
the fastener to break, shatter or to be driven right
through.
d) Never attempt to drive fasteners into materials
such as glass, marble, plastic, bronze, brass,
copper, rock, insulation material, hollow brick,
ceramic brick, thin sheet metal (< 4 mm), cast
iron or cellular concrete.
e) Before driving fasteners, check that no one is
present immediately behind or below the working
surface.
f) Keep the workplace tidy. Objects which could
cause injury should be removed from the working area. Untidiness at the workplace can lead to
accidents.
g) Keep the grips dry, clean and free from oil and
grease.
h) Do not use the tool where there is a risk of fire or
explosion unless it has been specially approved
for use under these conditions.
1.1.6 Mechanical safety precautions
Select the correct fastener guide and fastener
combination for the job on hand. Failure to use
the correct combination of these items may result
in injury or cause damage to the tool and/or lead to
unsatisfactory fastening quality.
b) Use only fasteners of a type approved for use with
the tool.
c) Do not tamper with or modify the tool or parts of
it, especially the piston.
a)
1.1.7 Thermal safety precautions
If the tool has overheated, allow it to cool down.
Do not exceed the recommended fastener driving
rate.
b) If the tool has overheated, allow it to cool down.
c) Do not dismantle the tool while it is hot. Allow the
tool to cool down.
a)
d) The tool must be allowed to cool down if the
plastic cartridge strip begins to melt.
1.1.8 Danger of explosion
d) Store unused cartridges in a locked place where
they are not exposed to dampness or excessively
high temperatures.
1.1.9 Personal protective equipment
Use only cartridges of a type approved for use
with the tool.
b) Remove the cartridge strip from the tool carefully.
c) Do not attempt to forcibly remove cartridges from
the magazine strip or tool.
a)
en
The user and any other persons in the vicinity must
wear suitable eye protection, a hard hat and ear
protection while the tool is in use or when remedying
a problem with the tool.
2 General information
2.1 Safety notices and their meaning
Symbols
DANGER
Draws attention to imminent danger that will lead to
serious bodily injury or fatality.
WARNING
Draws attention to a potentially dangerous situation that
could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that
could lead to slight personal injury or damage to the
equipment or other property.
NOTE
Draws attention to an instruction or other useful information.
2.2 Explanation of the pictograms and other
information
Warning signs
Read the
operating
instructions
before use
Location of identification data on the tool
The type designation and serial number can be found on
the type identification plate on the tool. Make a note of
this data in your operating instructions and always refer
to it when making an enquiry to your Hilti representative
or service department.
Type:
Generation: 01
Serial no.:
General
warning
Warning:
explosive
substances
Warning: hot
surface
Obligation signs
Wear
protective
glasses
Wear a hard
hat
Wear ear
protection
19
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
3 Description
3.1 Use of the product as directed
en
The tool is designed for professional use in fastening applications where nails, threaded studs and composite fasteners
are driven into concrete, steel and sand-lime block masonry.
The tool is for hand-held use only.
Modification of the tool is not permissible.
The tool may not be used in an explosive or flammable atmosphere unless it has been approved for use under these
conditions.
To avoid the risk of injury use only genuine Hilti fasteners, cartridges, accessories and spare parts or those of
equivalent quality.
Observe the information printed in the operating instructions concerning operation, care and maintenance.
The tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used
not as directed.
The tool may be operated, serviced and repaired only by trained personnel. This personnel must be informed of any
special hazards that may be encountered.
As with all powder-actuated fastening tools, the tool, cartridges and fasteners form a technical unit. This means that
trouble-free fastening with this system can be assured only if the Hilti fasteners and cartridges specially manufactured
for it, or products of equivalent quality, are used. The fastening and application recommendations given by Hilti apply
only when these conditions are observed.
The tool features a 5-way safety system for the safety of the user and all bystanders.
3.2 Piston principle
The energy from the propellant charge is transferred to a piston, the accelerated mass of which drives the fastener into
the base material. Due to use of this piston principle, the tool is classified as a “low velocity tool”. As approximately
95% of the kinetic energy is absorbed by the piston, the fastener is driven into the base material in a controlled fashion
at much reduced velocity (less than 100 m/s). The fastener driving process ends when the piston reaches the end of
its travel. Due to these technical measures, it is highly unlikely that through-shots will occur.
3.3 Drop-firing safety device
The drop-firing safety device is the result of coupling the firing mechanism with the cocking movement. This prevents
the tool from firing when dropped onto a hard surface, no matter at which angle the impact occurs.
3.4 Trigger safety device
The trigger safety device prevents the tool firing when only the trigger is pulled. The tool must be pressed against a
firm surface before a fastener can be released.
3.5 Contact pressure safety device
The tool can be fired only when pressed fully against a firm surface with a force of at least 50 N.
3.6 Unintentional firing safety device
The tool is also equipped with an unintentional firing safety device. This prevents the tool from firing if the trigger is first
pulled and the tool then pressed against the work surface. The tool can be fired only when it is first pressed correctly
against the work surface and the trigger subsequently pulled.
3.7 Range of fasteners available for various applications
Fasteners
Ordering designation
Application
X-U
High-strength nail for fastening on highstrength steel and concrete in a wide range
of applications
Standard nail for fastening on concrete
X-C
X-S
Standard nail for efficient fastening on steel
X-CR
Stainless steel nail for fastening in damp or
corrosive surroundings
Fastener for positioning formwork
X-FS C52
20
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Ordering designation
Application
X-SW C37
Flexible washer fastener for fastening
plastic sheeting and thin insulating
materials to concrete and steel
Suspension system with threaded connection
Fastening clip for wire hangers
X-HS / X-HS-W
X‑CC
X-(D)FB / X-EMTC
Metal conduit clip for fastening electrical
conduits or insulated pipes (hot or cold) in
water supply and heating installations
Cable clasp for fastening electric cables flat
on ceilings and walls
Bunched cable holder for fastening cables
on ceilings and walls
Fastener for plastic (PVC) electric cable
trunking
Threaded stud for temporary fastenings on
concrete and steel
Approved (ETA) DX-Kwik fastening system
use on concrete with predrilling
X‑EKB
X-ECH
X‑ET
X-(E)M/W/6/8 ... P8
X-DNH / DKH X-M6/8H
Cartridges
Ordering designation
Color
Power level
6.3/10 M green
Green
Light
6.3/10 M yellow
Yellow
Medium
6.3/10 M red
Red
Heavy
4 Accessories, consumables
NOTE
For information about further accessories and fasteners for use with the tool, please contact your local Hilti
representative.
Safety accessories and cleaning set
Designation
Cleaning set
Hilti spray
Spring clip spare parts pack
Operating instructions
Stabilizer (fragmentation guard, only USA)
Additional baseplate
Spare part pack
Stop Gliss anti-slip paper
Standard accessories
Designation
Item number
Fastener guide 21/F3-1
2554
Baseplate 21/s1
2556
Piston 21/SDF
409298
Spring clip
2162
21
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
en
5 Technical data
Right of technical changes reserved.
Tool
en
DX 35
Weight
1.9 kg
Tool length
286 mm
Maximum fastener length
37 mm
Cartridges
6.3/10 M (25 cal. short) green, yellow, red
Recommended maximum fastening rate
300/h
6 Before use
6.1 Checking the tool
NOTE
Read the operating instructions before the tool is operated for the first time.
WARNING
Do not operate the tool when parts are damaged
or when the controls do not function correctly. If
necessary, have the tool repaired at an authorized
Hilti service center.
Check that no cartridge strip is loaded in the tool. If there
is a cartridge strip in the tool, pull it up out of the tool by
hand from above.
Check all external parts of the tool for damage and check
that all controls operate faultlessly.
Check the piston and spring clip for wear and ensure that
the parts have been fitted correctly.
7 Guidelines
7.1 Fastening guidelines
These guidelines must be observed at all times.
NOTE
For detailed information, please ask your local Hilti sales and service office for a copy of the applicable technical
guidelines or national technical regulations.
7.1.1 Minimum distances and spacing
Minimum distances and spacing when fastening to steel
%
$
&
G
22
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
A
min. edge distance = 15 mm (⁵⁄₈")
B
min. spacing = 20 mm (³⁄₄")
C
min. base material thickness = 4 mm (⁵⁄₃₂")
Minimum distances and spacing when fastening to concrete
%
A
$
min. edge distance = 70 mm (2³⁄₄")
b
min. spacing = 80 mm (3¹⁄₈")
c
min. base material thickness = 100 mm (4")
(7 &
en
7.1.2 Depth of penetration
NOTE
Examples and specific information can be found in the Hilti Fastening Technology Manual.
Nail lengths for steel
ET
Depth of penetration: 12 ± 2 mm (½" ± ¹⁄₁₆")
ET
Depth of penetration: 22 mm (max. 27 mm) (⁷⁄₈"
(max. 1"))
ET
Nail lengths for concrete
ET
8 Operation
or the piston to be driven into a part of the body. Never
press the tool against a part of the body.
WARNING
The material may splinter or fragments of the magazine
strip may fly off when the fastener is driven. The user of
the tool and other persons in the immediate vicinity
must wear protective glasses and a hard hat. Splintering material presents a risk of injury to the eyes and
body.
CAUTION
The fastener driving action is initiated by ignition of a propellant charge. The user of the tool and other persons
in the immediate vicinity must wear ear protectors.
Exposure to noise can cause hearing loss.
WARNING
Never make the tool ready to fire by pressing it against a
part of the body (e.g. the hand). This could cause a nail
WARNING
Never redrive a fastener. This may cause the fastener
to break and the tool may jam.
WARNING
Never drive fasteners into existing holes unless this
is recommended by Hilti (e.g. DX‑Kwik).
CAUTION
If the tool has overheated, allow it to cool down. Do
not exceed the recommended fastener driving rate.
8.1 Procedure if a cartridge fails to fire
If a cartridge fails to fire or misfires, always proceed as
follows:
Keep the nose of the tool pressed at right angles against
the working surface for 30 seconds.
23
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
en
If the cartridge still fails to fire, withdraw the tool from the
working surface, taking care to avoid pointing it toward
your body or toward bystanders.
Load the next cartridge on the strip by cycling the tool.
Use up the remaining cartridges on the strip and remove
the used cartridge strip from the tool. The (partly) used
cartridge strip must then be disposed of appropriately to
prevent further use or misuse of any unfired cartridges.
8.2 Loading the tool 2
1.
2.
3.
Push the nail, head first, into the nose of the tool
from the front until it is held in place in the tool by
the washer on the nail.
Push the cartridge strip, narrow end first, into the
grip of the tool from below until the full length of the
cartridge strip is inside the grip.
If you wish to use a partly-used cartridge strip, pull
the strip upwards by hand out of the tool slightly until
the first unused cartridge is in place in the cartridge
chamber.
8.3 Selecting the cartridge
1.
2.
3.
Select the cartridge power level according to the
application to be carried out.
If you cannot estimate this on the basis of previous
experience, always begin with the lowest power.
Select the weakest cartridge color and make a trial
fastener placement.
Drive a nail.
If the nail is not driven in deeply enough, try using a
heavier cartridge.
8.4 Driving a fastener 3
WARNING
Always observe the safety rules listed in the operating
instructions.
1.
2.
Press the tool against the working surface at right
angles.
Drive the fastener by pulling the trigger.
8.5 Cycle the tool. 4
NOTE
If the cycling action (i.e. pulling out, pushing back in)
is stiff, this indicates that the tool needs to be cleaned.
Service the tool! (see section 9.3).
1.
2.
3.
After driving a fastener, grip the collar at the nose of
the tool between the thumb and forefinger.
Pull the nose unit forward in the main axis of the tool
as far as it will go.
Then pull the fastener guide all the way back to its
original position.
This movement brings the piston back to its starting
position and advances the cartridge strip to the next
cartridge.
The tool is then ready to drive the next fastener.
8.6 Unloading the tool 5
Check that there is no cartridge strip or fastener in the
tool.
If there is a cartridge strip or fastener in the tool, pull the
cartridge strip up out of the tool by hand from above and
remove the fastener from the fastener guide.
9 Care and maintenance
CAUTION
The tool may get hot during use. You could burn your
hands. Wear protective gloves when carrying out care
and maintenance. Allow the tool to cool down.
CAUTION
When this type of tool is used under normal operating
conditions, dirt and residues build up inside the tool and
functionally relevant parts are also subject to wear. Regular inspections and maintenance are thus essential
in order to ensure reliable operation. We recommend
that the tool is cleaned and the condition of the piston checked at least daily when the tool is subjected
to intensive use, and at the latest after driving 3,000
fasteners.
WARNING
All cartridges must be removed from the tool. Check
to ensure that no fastener is present in the fastener
guide before carrying out maintenance or repairs.
24
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
9.1 Care of the tool
Clean the outside of the tool at regular intervals with a
slightly damp cloth.
WARNING
Do not clean with a spray or pressure washer. Do not
permit foreign objects to enter the interior of the tool.
9.2 Maintenance
Check all external parts of the tool for damage at regular
intervals and check that all controls operate faultlessly.
Do not operate the tool if parts are damaged or when the
controls do not function faultlessly. If necessary, the tool
should be repaired by Hilti Service.
Use the tool only with the recommended cartridges. An
incorrect cartridge selection can lead to a premature
failure of parts of the tool.
CAUTION
Dirt and residues in DX tools contain substances that
may be hazardous to your health. Do not inhale dust /
or dirt from cleaning. Keep the dust or dirt away from
foodstuffs. Wash your hands after cleaning the tool.
Never use grease for the maintenance/lubrication of
parts of the tool. This may lead to malfunctions. Use
only Hilti lubricant spray or a product of equivalent
quality.
9.3 Servicing the tool
Service the tool if fastener driving power is found to be
inconsistent, if cartridges misfire or if parts of the tool
no longer move or operate smoothly and easily. In other
words, The required contact pressure increases, trigger
resistance increases, the cartridge magazine strip can
only be removed with a degree of difficulty or the cycling
action becomes stiff.
9.3.1 Disassembling the tool 6
CAUTION
Forcing the spring clip into place may cause it to jump off
with considerable energy. Take care to avoid injuring
yourself or others. Hold the assembly with its back
facing downwards.
1.
2.
3.
4.
5.
6.
Lift the spring clip with a screwdriver or a nail and
turn. Pull the stop backwards and remove.
Pull out the insert.
Press the spring clip away with a screwdriver or
a nail. If need be, replace the spring clip if it is
damaged.
Separate the baseplate together with the fastener
guide from the piston guide.
Remove the piston.
Allow the fastener guide to slide out of the baseplate.
NOTE If the fastener guide does not slide of its own
accord, prod it out with the piston.
9.3.2 Checking the piston for wear
NOTE
Never use a worn or damaged piston and do not attempt
to manipulate or modify the piston.
Replace the piston when:
- the piston is broken
- the piston is badly worn or chipped (e.g. a 90° segment
broken away).
- the piston rings are cracked or missing.
- the piston is bent (check by rolling the piston on a
smooth, flat surface).
9.3.3 Checking the fastener guide for wear
Replace the fastener guide if the tubular section is damaged (e.g. bent, widened or cracked).
9.3.4 Checking the spring clip for wear
en
Replace the spring clip if it is badly worn or bent.
9.3.5 Cleaning
Clean the tool at least once a week or, respectively,
immediately after each period of heavy use (after driving
approx. 3,000 nails).
Use the appropriate brushes to clean the individual parts:
1.
2.
3.
4.
Clean the fastener guide and sleeve inside and out.
Clean the piston and piston rings until the parts
move freely.
Clean the piston guide, inside and out.
Clean the inside of the housing.
9.3.6 Lubrication
Spray the cleaned parts lightly with the Hilti lubricant
spray supplied. Use only Hilti lubricant spray or a product
of comparable quality.
9.3.7 Assembling the tool 7
NOTE
Handle the small parts carefully. They could get lost.
1.
2.
3.
4.
5.
6.
Introduce the fastener guide into the baseplate.
Slide the piston to the end of the piston guide.
Place the baseplate together with the fastener guide
onto the piston guide.
NOTE Grooves for the stop must be in line.
Press the spring clip into the opening of the piston
guide.
Introduce the insert into the tool so that the groove
aligns with the opening for the stop.
Insert the stop and pull the spring clip over it with a
screwdriver or a nail.
9.3.8 Checking
After carrying out care and maintenance, check that all
protective and safety devices are fitted and that they
function faultlessly.
NOTE
The tool can be checked, as follows, to determine
whether it is ready to fire: Press the nose of the unloaded tool (i.e. no cartridges or fastener in the tool)
firmly against a hard surface and pull the trigger. A clearly
heard click from the trigger mechanism indicates that the
tool was ready to fire.
25
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
10 Troubleshooting
WARNING
The tool must be unloaded before taking any steps to remedy faults.
en
Fault
Possible cause
Remedy
Higher force required to cycle
the tool.
Higher force required to press
the tool against the surface.
Trigger resistance increases.
Build-up of combustion residues.
Service the tool (see 9.3)
Build-up of combustion residues.
Service the tool (see 9.3)
Build-up of combustion residues.
Service the tool (see 9.3)
The cartridge strip is difficult to
remove.
The tool cannot be fired.
Build-up of combustion residues.
Service the tool (see 9.3)
The tool is not cycled. The cartridge
has already been fired.
Cycle the tool (see 8.5)
Remove the used cartridge and load
an unused cartridge.
The tool was not pressed fully against
the working surface.
Press the tool fully against the working surface.
The tool needs to be cleaned.
Clean the tool.
The piston is damaged.
Check the piston (see 9.3.2) and replace it if necessary.
The tool is damaged.
If the problem persists, contact your
local Hilti Center.
The piston was in the wrong position.
Remove the cartridge strip and cycle
the tool.
See section: 8.5 Cycle the tool. 4
Bad cartridges.
Change the cartridge strip (use a different / dry package if necessary).
If the problem persists: service the
tool (see 9.3)
Tool jams.
Misfire: the fastener is only
partly driven into the base material.
26
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Fault
Possible cause
Remedy
The cartridge strip doesn’t advance.
The cartridge strip is damaged.
Change the cartridge strip.
The tool needs to be cleaned.
Clean the tool.
The tool is damaged.
If the problem persists, contact your
local Hilti Center.
The cartridge strip cannot be
removed.
The tool has overheated.
Allow the tool to cool down.
Subsequently, carefully remove the
cartridge strip from the tool.
WARNING
Do not attempt to forcibly remove
cartridges from the magazine strip or
tool.
If the problem persists, contact your
local Hilti Center.
A cartridge doesn’t fire.
Bad cartridge.
Pull the cartridge strip through to the
next cartridge.
The tool needs to be cleaned.
Servicing the tool
WARNING
Check that the correct cartridges are
used and that they are in faultless
condition.
See section: 9.3 Servicing the tool
If the tool cannot be disassembled,
contact your local Hilti Center.
The tool is pressed against the working surface for too long before firing.
Fire the tool sooner after pressing it
against the working surface.
Remove the cartridge strip.
Stop using the tool immediately.
Remove the cartridge strip and allow
the tool to cool.
WARNING
Do not attempt to forcibly remove
cartridges from the magazine strip or
tool.
Clean the tool and remove any loose
cartridges.
If the tool cannot be disassembled
contact your local Hilti Center.
The cartridge strip melts.
The fastener driving rate is too high.
en
27
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Fault
Possible cause
Remedy
A cartridge detaches itself from
the cartridge strip.
The fastener driving rate is too high.
Stop using the tool immediately.
Remove the cartridge strip and allow
the tool to cool.
WARNING
Do not attempt to forcibly remove
cartridges from the magazine strip or
tool.
Clean the tool and remove any loose
cartridges.
If the tool cannot be disassembled
contact your local Hilti Center.
The piston gets stuck in the
base material / fastener is
driven too deeply.
The fastener is too short.
Use a longer fastener.
The fastener has no washer.
Use a fastener with washer for applications on wood.
Driving power is too high.
Use a less powerful cartridge.
The fastener is too long.
Use a shorter fastener.
NOTE
Observe the min. fastener driving
depth requirements. Obtain a copy
of the Fastening Technology Manual
from your local Hilti Center.
Driving power is too low.
Use a more powerful cartridge.
Hard surface (steel, concrete)
Use a more powerful cartridge.
NOTE
The DX 35 has no power regulation.
Hard and/or large aggregates in the
concrete.
Use a more powerful cartridge.
If necessary, use a more powerful tool
and nails with a higher application
limit (e.g. DX 460 with X-U nails).
A rebar is located just below the concrete surface.
Use a shorter nail.
Use a nail with a higher application
limit.
en
The fastener is not driven
deeply enough.
The nail bends.
28
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Fault
Possible cause
Remedy
Concrete spalling.
Hard/old concrete.
Use a shorter nail.
Hard and/or large aggregates in the
concrete.
Use a more powerful cartridge.
If necessary, use a more powerful tool
and nails with a higher application
limit (e.g. DX 460 with X-U nails).
Damaged nail head.
The nail doesn’t penetrate
deeply enough.
The nail doesn’t hold in the
base material.
A rebar is located just below the concrete surface.
Use a shorter nail.
Use a nail with a higher application
limit.
Driving power is too high.
Use a less powerful cartridge.
Application limit exceeded (very hard
material).
Use a nail with a higher application
limit.
The piston is damaged.
Change the piston.
Driving power is too low.
Use a more powerful cartridge.
Application limit exceeded (very hard
material).
Use a nail with a higher application
limit.
The system is unsuitable.
Use a more powerful system, e.g.
DX 76 (PTR).
Thin steel base material (< 4 mm)
Use a different cartridge.
Use a nail suitable for thin steel base
material.
29
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
en
Fault
Possible cause
Remedy
Nail breakage.
Driving power is too low.
Use a more powerful cartridge.
Application limit exceeded (very hard
material).
Use a shorter nail.
Use a nail with a higher application
limit.
Driving power is too high.
Use a less powerful cartridge.
Use a nail with a “top hat”.
Use a nail with a washer.
en
The head of the nail punches
through the material fastened
(sheet metal).
11 Disposal
Most of the materials from which Hilti tools or appliances are manufactured can be recycled. The materials must
be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for
taking back old tools and appliances for recycling. Ask Hilti customer service or your Hilti representative for further
information.
12 Manufacturer’s warranty - tools
Hilti warrants that the tool supplied is free of defects in
material and workmanship. This warranty is valid so long
as the tool is operated and handled correctly, cleaned
and serviced properly and in accordance with the Hilti
Operating Instructions, and the technical system is maintained. This means that only original Hilti consumables,
components and spare parts, or other products of equivalent quality, may be used in the tool.
Additional claims are excluded, unless stringent national rules prohibit such exclusion. In particular, Hilti
is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inability to
use the tool for any purpose. Implied warranties of
merchantability or fitness for a particular purpose are
specifically excluded.
This warranty provides the free-of-charge repair or replacement of defective parts only over the entire lifespan
of the tool. Parts requiring repair or replacement as a
result of normal wear and tear are not covered by this
warranty.
For repair or replacement, send the tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
30
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
This constitutes Hilti’s entire obligation with regard to
warranty and supersedes all prior or contemporaneous
comments and oral or written agreements concerning
warranties.
13 EC declaration of conformity (original)
Designation:
Type:
Powder-actuated fastening tool
DX 35
Generation:
Year of design:
Hilti Corporation, Feldkircherstrasse 100,
FL‑9494 Schaan
en
01
1976
We declare, on our sole responsibility, that this product
complies with the following directives and standards:
2006/42/EC, 2011/65/EU.
Norbert Wohlwend
Head of Quality & Processes Management
BU Direct Fastening
04/2013
Tassilo Deinzer
Head BU Measuring Systems
BU Measuring Systems
04/2013
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
14 Confirmation of CIP testing
The following applies to C.I.P. member states outside
the EU and EFTA judicial area: The Hilti DX 35 has been
system and type tested. As a result, the tool bears the
rectangular PTB approval mark showing approval number S 806. Hilti thus guarantees compliance with the ap-
proved type. Unacceptable defects or deficiencies, etc.
determined during use of the tool must be reported to the
person responsible at the approval authority (PTB) and
to the Office of the Permanent International Commission
(C.I.P.).
15 Health and safety of the operator
15.1 Noise information
Powder-actuated fastening tool
Type
DX 35
Model
Series
Caliber
6.3/10 yellow
Application
Fastening 1 mm sheet steel to concrete (C40) with the
X-U22 P8
The tool has no power regulation feature.
Declared measured values of noise characteristics according to 2006/42/EC Machinery Directive in conjunction
with DIN EN 15895
113 dB (A)
Noise (power) level, LWA, 1S 1
Emission noise-pressure level in the work station,
LpA, 1s 2
Peak sound pressure emission level, LpC, peak 3
109 dB (A)
142 dB (C)
1 ± 2 dB (A)
2 ± 2 dB (A)
3 ± 2 dB (C)
31
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Operation and set-up conditions: Set-up and operation of the pin driver in accordance with E DIN EN 15895-1 in the
semi-anechoic test room of Müller-BBM GmbH. The ambient conditions in the test room conform to DIN EN ISO 3745.
Testing procedure: Enveloping surface method in anechoic room on reflective surface area in accordance with
E DIN EN 15895, DIN EN ISO 3745 and DIN EN ISO 11201.
NOTE The noise emissions measured and the associated measurement uncertainty represent the upper limit for the
noise values to be expected during the measurements.
Variations in operating conditions may cause deviations from these emission values.
en
15.2 Vibration
Total vibration in accordance with 2006/42/EC does not
exceed 2.5 m/s².
32
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
Further information about user health and safety can be
found at www.hilti.com/hse.
Hilti Corporation
Printed: 12.08.2013 | Doc-Nr: PUB / 5125939 / 000 / 01
2143 / A3
2143
Hilti = registered trademark of Hilti Corp., Schaan
W 1037 | 0813 | 0-Pos. 3 | 1
Printed in China © 2013
Right of technical and programme changes reserved S. E. & O.
*2143*
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax:+423 / 234 29 65
www.hilti.com