falcon - Downloads

falcon - Downloads
FA L CON
WORLD CLASS SE CURITY
FALCON PREDATOR EVO3
2 Way Security System
Installation Manual
FOR NATIONWIDE INSTALLTION SERVICE
CALL 0800 622 474
HELPLINE: 0906 700 10 20
(All calls charged at 50p/min)
Falcon Security Ltd. Unit 9 Tanning Court, Warrington, Cheshire, WA1 2HF, UK
Internet: http://www.falcon-security.com Email: [email protected]
1
1) Specification
Working Voltage
Working Frequency
Code
Dc 10~16V
433.92 MHz ±1MHz
Hopping Code
Output
Arm
C7-6 Gray/White <Channel 3>
C7-7 Green/White <Door Unlock 2>
C7-9 Yellow <Indicator Light>
C7-11 Yellow/White <Indicator Light>
C7-12 Purple <Siren>
C7-13 Brown/White <Channel 2>
C7-14 Brown <Trunk Release>
C5 Red/Black <LED>
C2 Black/Green/Pin <Lock>
C2 White/Blue/Orange <Unlock>
C3 Black <Starter Kill>
<-> 200mA
<-> 200mA
<+> 15A
<+> 15A
<+> 1A
<-> 200mA
<-> 200mA
<-> 5mA
<+> 15A
<+> 15A
40/30A
2) Main Features
01> Hopping code data transmission
Central Lock System
02> Includes Two Way remote control
10> Compatible with dual stage
02> Power Saving transmitter
04> Code learning microprocessor
05> Dual stage Shock Sensor
Central Lock System
11> 2-Way FM/AM transmission up to
1000/350 meters
12> Instant alert by buzzer or
06> 5-separate trigger zones
vibration
07> 1 Auxiliary sensor port
13> Panic/Anti-Hijacking mode
08> 2 Auxiliary output ports
14> 10 programmable features
09> Compatible with all types of
3) LED Status Indicator
Slow flash
Fast flash
Steady flash
No light
:
:
:
:
Arm / Alarm / Panic / Anti-hijack
Auto Re-arm
Last door arm / send message to controller
Disarm mode
Note: Alarm will not accept the commands when sending a message to the controller.
2
4) Remote Control
01. Table of button functions
Button
BTN #1 once
BTN #1 2 sec.
BTN #2 once
BTN #3 once
BTN #3 2 sec.
BTN #1+2 then BTN #1
BTN #1+2 then BTN#1+2
BTN #2+3 once
BTN #1+2 then BTN#2
BTN #2+4 once
BTN#3+4
BTN #5 Once
IGN OFF
IGN On
Arm/Disarm
Panic
Channel 2 output
Vehicle Finder
Lock/Unlock
Panic
Channel 2 output
Anti-hijacking(1)
Anti-hijacking(2)
Mute Arm Mode
Boot release
Channel #3 output
RC battery saving
Vibration mode
Flash Light
Valet mode
Boot release
Channel 2 output
RC battery saving
Vibration mode
Flash Light
02. Battery Saving
a) Pressing button #2+4 once will start the battery saving mode and the buzzer
will sound to confirm. The remote control will enter battery saving mode 70sec.
after pressing button #1 to disarm the system. Pressing any button during the
70 sec. or while under in battery saving mode will deactivate the battery saving
mode till next time the system is disarmed.
b) Under battery saving mode, pressing button #2+4 once again will turn off the
battery saving mode and the buzzer will sound to confirm.
03. Vibration and Audible Mode
Pressing button #3+4 once under any mode will switch between vibration or
audible mode.
04. Flash Light
Press and hold button #5 for one second will turn on the flash light for as long as
button #5 is pressed.
05. Powering on the LED Remote Control
When inserting the battery the buzzer of LED remote will sound and then the
3
blue/red/green LED and white flash light will flash for 0.5 sec. alternately.
06. Blue LED
* Press any button except button #5 and the blue LED will flash for 0.5sec. and the
battery power will be checked at the same time
* Insufficient Battery power is indicated by:
- Blue LED flashes 3 sec. then off
- Buzzer sounds four times
07. Red LED
a) When the system is armed the remote control will beep once and the red LED
flash 15 sec. to confirm.
b) When the system is disarmed, the LED remote will beep two times and the red
LED will be off.
08. Trigger and Responses
a) Shock sensor triggers
* When disarming the system:
If the shock sensor has been triggered during the armed mode, the Red LED
will flash once for 15 sec. and buzzer sounds.
* When the system is in armed mode:
The red LED will flash once for 15 sec. and the buzzer will sound for 15 sec.
if the shock sensor is triggered.
b) Bonnet & Boot triggers
* When arming the system:
The red LED will flash twice for 15 sec. and buzzer sounds if the bonnet/boot
is not closed properly
* When disarming the system:
If the bonnet or boot has been triggered during the armed mode the Red LED
will flash twice for 15 sec. and the buzzer sounds when disarming the system
* When the system is in armed mode:
The red LED will flash twice for 15 sec. and the buzzer will sound for 15 sec.
if the bonnet or boot is triggered
c) Door triggers
* When arming the system:
The red LED will flash three times for 15 sec. and the buzzer sound if the door
is not closed properly
* When disarming the system:
If the door has been triggered during the armed mode, when disarming the
system the Red LED will flash three times for 15 sec. and the buzzer sounds.
* When the system is in armed mode:
The red LED flashes three times for 15 sec. and buzzer will sound for 15 sec.
if the door is triggered.
4
d) Ignition triggers
* When disarming the system:
If the ignition has been triggered during the armed mode, when disarming
the system the Red LED will flash four times for 15 sec. and buzzer sounds.
* When the system is in armed mode:
The red LED flashes four times for 15 sec. and buzzer will sound for 15 sec.
5) Programming Remote Controls
The alarm system comes with one 2-Way 4 button remote control which is
pre-programmed into the system memory. The alarm can support up to 4 remote
controls, follow the steps below to enter code-learning procedure to program new
remote controls.
* Under the disarm mode
* Turn the ignition switch ON/OFF 3
times (each time within 1 sec., or alarm system will ignore it) and stay in ON
position
* Siren will sound for 2 seconds, and the alarm will enter into code learning mode
* Press button #1 within 10 seconds, the siren will chirp twice and the hazard
lights flash twice to confirm the code has learned
* Apply the same procedure for second, third and fourth remote controls
* If the ignition is turned OFF or 10 seconds elapses between any of the steps then
siren will chirp 4 times, the lights will flash 4 times, and the alarm will leave the
code learning mode.
* Once 4 remote controls have been programmed the alarm will automatically
leave the code learning mode.
6) Feature Programming Options
With the alarm disarmed open the
door
Switch the ignition on and off three
times and keep it in the “On” position
The siren will chirp for two seconds,
then the system will enter into the
programming option mode
Within 10 seconds press button #1
the same number of times as the
function you wish to program. Press
button #2 to confirm and the siren will
chirp the same number of times to
confirm the selected function.
Then set up the function by pressing
button #1, #2 or #3
* System will quit the programming
option automatically after 10 seconds
or if the ignition is turned off.
5
No.
Function
Button #1
[Chirp once]
01.
Passive/Last Door Arming
Disable
02.
Passive Locking
Disable
03.
Smart Ignition Locking
Disable
04.
Door Lock Time
1 Pulse
05.
Alarm Time
30 sec.
06.
Interior Light Delay
Disable
07.
Auto Re-arm
Disable
08.
Dual Stage Unlock/Door Unlock 2
Disable
09.
Anti-Hijacking
Disable
10.
CH3 Output
Disable
Remark: Factory Default <Gray Background / Button #1>
Button #2
[2 Chirps]
Button #3
[3 Chirps]
Enable
Enable
Enable
2 Pulse
60 sec.
Enable
Enable
Enable
Enable
Enable
xxx
xxx
xxx
4 seconds
Continuous
xxx
xxx
xxx
xxx
xxx
7) Arm
7.1> With the alarm disarmed and the ignition off pressing button #1 will arm the
alarm, the doors will lock and the siren will chirp once and the indicator lights flash
once to confirm the arm status. The LED will turn on and flash slowly after 2
seconds.
7.2> If a door, the bonnet or boot were not closed properly when the system was
armed the siren will chirp and the indicator lights flash three times, the doors will
lock and the lights will flash once again and the siren will sound a long chirp and
a short chirp to warn you.
8) Disarm/Override
8.1> With the alarm armed pressing button #1 will disarm the system, the doors
will unlock and the siren will chirp twice and the indicator lights will flash twice to
confirm. The LED will turn off.
8.2> Override – to disarm the system without a remote control (eg. In case of flat
battery/lost remote), open the door and the alarm will sound, switch the ignition
on and off 4 times to disarm (on-off-on-off-on-off-on-off).
The lights will keep on flashing until door or bonnet/boot is closed while the
ignition is on, if doors, hood or trunk is opened.
8.3>
9) Alarm Mode
If any installed sensors are triggered the system will enter alarm mode and the
siren will sound and indicators flash unless the alarm is triggered by the first stage
of the shock sensor in which case the siren will chirp 3 times only to warn intruders.
9.1>
9.2> If the ignition is triggered (ACC is turned to “on” position), the system will
enter the alarm mode until the ignition is turned off.
9.3> If doors, bonnet or boot are opened the siren will sound and stop after 30 or
60 seconds as pre setting of option 5 even if the door, bonnet or boot is still open
unless option 5 set at ‘continuous’ in which case the siren will sound until the door,
bonnet or boot is closed.
9.4> If the alarm is triggered, press button #1 once, the siren will chirp once, the
6
doors will lock (if unlocked) and the system remains in the arm mode.
10) Panic
Under any mode, press button #1 for 2 seconds, the system will enter into the arm
mode. The indicator lights will flash and siren sounds.
11) Mute Arm mode
11.1> With the alarm disarmed press button #1+#2 once, the lights will flash once,
then press button #1 again within 1 second and the system will enter into the arm
mode; the lights will flash once more to confirm and the doors will lock.
under the mute mode: if shock sensors are triggered, only the lights will flash.
If the ignition, doors or bonnet/boor are triggered the siren will sound and lights
flash and mute mode will be cancelled.
11.2>
12) Valet Mode
12.1> With the alarm disarmed switch the ignition on and press buttons #1+#2
once at the same time; the lights will flash once, within 2 seconds press button
#1+#2 once again at the same time, the siren will chirp once to confirm the
system is now in valet mode. Use the same procedure to exit valet mode, and siren
will chirp twice to confirm.
12.2> Under valet mode, only door lock and unlock can be operated by remote
control and the indicator lights will flash once or twice.
13) Channel-2 output
13.1> Pressing button #2 once with the alarm armed or disarmed will activate
channel-2 for 0.5 second (Negative pulse). If the alarm is armed the shock sensor
will be bypassed for 8 sec. at the same time.
14) Boot Release
14.1> Pressing buttons #2+#3 once at the same time will operate the boot release
output. If the system is armed it will be disarmed.
15) Channel-3 output
15.1> When programmed as disabled: Pressing buttons #1+#2 followed by button
#2 will send a constant negative output through CH-3 until button #2 is released.
15.2> When programmed as enabled: Total closure output - A 30 second negative
output will be sent through CH3 when pressing button #1 to arm the system, the
shock sensor will be temporarily bypassed at the same time.
16) Remote Anti-Hijacking
16.1> With the ignition on, press button #3 once and the LED & lights will flash to
warn intruders.
16.2> When the ignition is off press button #3 and the lights will flash for the
programmed alarm duration and then the system will enter into the arm mode.
* Anti-hijacking flow chart is listed below.
17) Vehicle Finder
7
17.1> Pressing button #3 once will flash the indicators for 30 seconds. If the alarm
is disarmed it will enter into the arm mode.
18) Passive/Last Door Arming
Whenever the ignition is switched off and the doors closed the alarm will enter the
arm mode 20 seconds later. If passive locking is also enabled the doors will be
locked.
19) Ignition Door Locking
19.1> With the alarm disarmed switching the ignition on will cause the doors to be
locked automatically after 30 seconds; when the ignition is switched off the doors
will be unlocked automatically.
19.2> The doors will not be locked if a door is opened within 30 seconds of turning
the ignition on.
20) Interior light Delay
If Interior-Light Delay is enabled: When arming the system only the ignition will be
activated immediately, the doors, bonnet, boot and shock sensor will be activated
after 15 seconds.
21) Auto Re-Arm
When Enabled: After pressing button #1 to disarm the alarm the LED will flash
rapidly. If a door is not opened or the ignition turned on withinr 30 seconds the
lights will flash once, the siren will chirp once and the system will enter into the arm
mode.
22) Door Unlock 2
22.1> When Disabled: While disarming, door unlock & unlock 2 will be activated at
same time.
22.2> When Enabled: While disarming, press button #1 within 3 seconds to
activate door unlock 2.
24) Suggested location to install the transceiver
*
*
*
*
Install the antenna at the right or left upper of the windshield
Keep the antenna at least 5cm away from the car frame
Don’t power on the main unit if the antenna is not connected
Keep the antenna at least 5cm apart from solar control window film
8
9
10
11
12
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement