C 546BEE - NAD Electronics Australia

C 546BEE - NAD Electronics Australia
NEDERLANDS
Owner’s Manual
SVENSKA
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
Compact Disc Player
ENGLISH
C 546BEE
РУССКИЙ
®
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
SAVE THESE INSTRUCTIONS FOR LATER USE.
FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE
AUDIO EQUIPMENT.
FRANÇAIS
ESPAÑOL
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
1 Read instructions - All the safety and operating instructions should be
read before the product is operated.
2 Retain instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
5Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for
cleaning.
6Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
9
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
10Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
11 Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company.
The primary method of isolating the amplifier from the mains supply
is to disconnect the mains plug. Ensure that the mains plug remains
accessible at all times. Unplug the AC power cord from the AC outlet if
the unit will not be used for several months or more.
12 Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
13Power - Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
РУССКИЙ
2
14 Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Section
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
15Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to lightning
and power-line surges.
16 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
17Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
18 Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
WARNING: THE APPARATUS SHOULD NOT BE EXPOSED TO
DRIPPING OR SPLASHING, AND OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS.
AS WITH ANY ELECTRONIC PRODUCTS, USE CARE NOT TO SPILL
LIQUIDS INTO ANY PART OF THE SYSTEM. LIQUIDS CAN CAUSE A
FAILURE AND/OR A FIRE HAZARD.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
CAUTION
The C 546BEE employs a Laser System. To ensure proper use of this product,
please read this owner’s manual carefully and retain for future reference.
Should the unit require maintenance, contact an authorized service
location. Use of controls, adjustments or the performance of procedures
other than those specified may result in exposure to laser radiation. To
prevent direct exposure to laser beam, do not try to open the enclosure.
Visible laser radiation when the enclosure is opened.
DO NOT STARE INTO BEAM.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
FRANÇAIS
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE”
WITHIN THE PRODUCT’S ENCLOSURE THAT MAYBE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
ESPAÑOL
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN
THE LITERATURE ACCOMPANYING THE APPLIANCE.
ITALIANO
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
INDUSTRY CANADA REQUIREMENT
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
The socket-outlet shall be installed near the apparatus and shall be easily
accessible.
TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC
MAINS, DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE
AC RECEPTACLE.
DEUTSCH
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) when the product exhibits a distinct change in performance-this
indicates a need for service.
20 Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
23Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves or other products (including amplifiers)
that produce heat.
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN
READILY ACCESSIBLE.
CAUTION
Changes or modifications to this equipment not expressly approved by
NAD Electronics for compliance could void the user’s authority to operate
this equipment.
CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit
(from the largest outer dimensions including projections) that is equal to or
greater than shown below.
Left and Right Panels: 10 cm
Rear Panel: 10 cm
Top Panel: 50 cm
РУССКИЙ
This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
NEDERLANDS
a)
b)
c)
d)
FCC WARNING
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
SVENSKA
19 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
FRANÇAIS
INFORMATION ABOUT COLLECTION AND DISPOSAL OF
WASTE BATTERIES (DIRECTIVE 2006/66/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION) (FOR
EUROPEAN CUSTOMERS ONLY)
Batteries bearing any of these symbols indicate
that they should be treated as “separate
collection” and not as municipal waste. It is
encouraged that necessary measures are
implemented to maximize the separate
collection of waste batteries and to minimize the
disposal of batteries as mixed municipal waste.
NOTES ON ENVIRONMENTAL PROTECTION
At the end of its useful life, this product must not be disposed
of with regular household waste but must be returned to a
collection point for the recycling of electrical and electronic
equipment. The symbol on the product, user’s manual and
packaging, point this out.
The materials can be reused in accordance with their markings. Through
re-use, recycling of raw materials or other forms of recycling of old
products, you are making an important contribution to the protection of
our environment. Your local administrative office can advise you of the
responsible waste disposal point.
ESPAÑOL
End-users are exhorted not to dispose waste
batteries as unsorted municipal waste. In order
to achieve a high level of recycling waste batteries, discard waste batteries
separately and properly through an accessible collection point in your
vicinity. For more information about collection and recycling of waste
batteries, please contact your local municipality, your waste disposal service
or the point of sale where you purchased the items.
WARNING!
Batteries (battery pack or batteries installed) must not be exposed to
excessive heat such as sunshine, fire or the like.
NOTE: THE C 546BEE IS NOT AN AUTO VOLTAGE CD PLAYER.
CONNECT ONLY TO THE PRESCRIBED AC OUTLET, I.E., 120V 60HZ
OR 230V 50HZ.
ITALIANO
By ensuring compliance and conformance to proper disposal of waste
batteries, potential hazardous effects on human health is prevented and
the negative impact of batteries and waste batteries on the environment
is minimized, thus contributing to the protection, preservation and quality
improvement of the environment.
RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT)
The model and serial number of your new C 546BEE are located on the
back of the cabinet. For your future convenience, we suggest that you
record these numbers here:
Model no. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial no. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited
Copyright 2011, NAD Electronics International, a division of Lenbrook Industries Limited
4
INTRODUCTION
FRANÇAIS
ESPAÑOL
One more thing: We urge you to register your C 546BEE ownership on the
NAD Worldwide Web site:
http://NADelectronics.com/warranty
For warranty information contact your local distributor.
NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER
INTERFACE DISCREPANCIES IN THIS MANUAL. THE C 546BEE
OWNER’S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR
NOTICE. CHECK OUT THE NAD WEBSITE FOR THE LATEST VERSION
OF THE C 546BEE OWNER’S MANUAL.
ITALIANO
REFERENCE
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
NOTES ON DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
We encourage you to take a few minutes now to read right through this
manual. Investing a little time here at the outset might save you a good
deal of time later, and is by far the best way to ensure that you make the
most of your investment in the C 546BEE.
DEUTSCH
OPERATION
USING THE C 546BEE – CD MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CD-R AND CD-RW AUDIO DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PLAYING MP3/WMA FILES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
USING THE C 546BEE – USB MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LISTENING TO USB DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SELECTING DIRECTORIES OR FILES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
USING THE C 546BEE – CD 9 REMOTE CONTROL. . . . . . . . . . . . . . . . . . 13
NUMERIC KEY PAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
REPEAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RPT A-B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PROGRAM AND CLEAR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FILTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NEDERLANDS
IDENTIFICATION OF CONTROLS
FRONT PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CD 9 REMOTE CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SVENSKA
INTRODUCTION
GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UNPACKING AND SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
QUICK START. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
THANK YOU FOR CHOOSING NAD.
The C 546BEE CD Player is a technologically advanced and highly capable
product — yet we have invested great effort in making it simple and easy
to use. We have been careful to ensure that the C 546BEE is as musically
transparent and spatially accurate as possible, incorporating much of what
we’ve learned from over three decades of experience designing audio,
video and home-theater components. As with all our products, NAD’s
“Music First” design philosophy guided the C 546BEE’s design in such a
way that it can confidently promise you state-of-the-art audiophile-quality
music listening for years to come.
РУССКИЙ
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 2
ENGLISH
TABLE OF CONTENTS
5
INTRODUCTION
GETTING STARTED
ENGLISH
UNPACKING AND SETUP
QUICK START
WHAT’S IN THE BOX
Packed with your C 546BEE you will find:
• An audio cable connector
• The CD 9 remote control with two AA batteries
• A detachable AC power cord
• This owner’s manual on CD-ROM
In case you simply cannot wait to experience the performance of your new
NAD C 546BEE, we provide the following “Quick Start” instructions to get
you underway.
FRANÇAIS
SAVE THE PACKAGING
Please save the box and all of the packaging in which your C 546BEE
arrived. Should you move or otherwise need to transport your C 546BEE,
this is by far the safest container in which to do so. We’ve seen too many
otherwise perfect components damaged in transit for lack of a proper
shipping carton, so please: Save that box!
ESPAÑOL
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to
both sides and behind), and that will provide a clear line of sight, within
23 feet/7 meters, between the C 546BEE’s front panel and your primary
listening/viewing position. This will ensure reliable infrared remote control
communications. The C 546BEE generates a modest amount of heat, but
nothing that should trouble adjacent components. It is perfectly possible to
stack the C 546BEE on top of other components.
ITALIANO
DEUTSCH
NOTE ON INSTALLATION
IMPORTANT! Install the C 546BEE Compact Disc player on a level, vibrationfree surface. Severe vibration or operation in a tilted position may cause
the player to mis-track. The player may be stacked with other stereo
components, as long as there is adequate ventilation around it. If the
C 546BEE is placed in close proximity to a radio tuner (AM or FM), a VCR or
a television set, the operation of its digital circuits may produce static that
would interfere with reception of weak broadcast signals. If this occurs,
move the C 546BEE away from other devices or switch it off when viewing
or listening to broadcasts.
NEDERLANDS
SVENSKA
РУССКИЙ
6
Please make all the connections to your C 546BEE with the unit unplugged.
It is also advisable to power down or unplug all associated components
while making or breaking any signal or AC power connections.
PLAY A CD
1 Connect a twin RCA-to-RCA lead from the L (left) and R (right) Line
Output jacks to the corresponding CD inputs on your amplifier.
2 Connect the AC cord to the C 546BEE’s AC Mains input and then plug
into an AC outlet. The Standby LED indicator embedded around the
bezel of the STANDBY button will illuminate amber.
3 Press the STANDBY button to turn ON the player. The Standby LED
indicator will turn from amber to blue and illuminate the Vacuum
Fluorescent Display (VFD).
4 Press [STOP/OPEN] to open the disc drawer.
5 Place a CD, label side up, in the tray’s circular recess. Be certain that the
disc is centered within the recess.
6 Press [PLAY/PAUSE/SKIP]. The drawer closes automatically, and the disc
begins to play.
7 At any time you may rotate the [PLAY/PAUSE/SKIP] knob to select
different tracks on the disc.
8 Press [PLAY/PAUSE/SKIP] if you want to stop play temporarily while
keeping the pickup at its current position on the disc.
Press [PLAY/PAUSE/SKIP] again when you want to resume playback.
Press [STOP/OPEN] if you want to end play and reset the pickup to the
beginning of the disc.
IDENTIFICATION OF CONTROLS
11
ENGLISH
FRONT PANEL
12
FRANÇAIS
C 546BEE
If the disc tray is open and the Standby button is pressed, the disc tray
will draw close and the C 546BEE goes to standby mode.
NOTE
The C 546BEE will wake up from standby mode at the same SOURCE
setting it was in prior to being switched OFF to standby mode.
AUTO STANDBY
Auto Standby feature is an integral feature of C 546BEE that conforms to
ecodesign regulations. Auto standby mode can be enabled or disabled
by the following steps.
Enable Auto Standby mode
At operating mode, press and hold together front panel’s RANDOM
button and PLAY knob until the display shows “AutoStdby ON”.
Disable Auto Standby mode
At operating mode, press and hold together front panel’s RANDOM
button and PLAY knob until the display shows “AutoStdby OFF”.
CONDITIONS FOR AUTO STANDBY
With auto standby enabled, the C 546BEE will automatically go to
standby mode under the following conditions
Condition
Period of no user interface interaction
No disc
15 minutes
No USB
15 minutes
Stop mode
15 minutes
Pause mode
30 minutes
7
8
9
10
ESPAÑOL
6
3 DISC TRAY: With the disc tray open, insert a CD or other compatible
media disc face down onto the tray. Place the disc in the drawer,
centered in the smaller circular recess, with its label facing UP.
“Disc error” appears on the C 546BEE VFD if the disc is placed upside
down. “No Disc” appears on the C 546BEE VFD if there is no disc loaded.
NOTE
This player is not designed to accommodate neither a “damping disc”
placed on a CD nor two CDs stacked together. It plays audio CDs, but not
discs identified as CD-V, DVD, CD-I, CD-ROM or PHOTO CD. Refer also to
the item “CD-R AND CD-RW AUDIO DISCS” at the “USING THE C 546BEE –
CD MODE” section of the “OPERATION” page.
4STOP/OPEN: This dual-function button alternates between stopping
playback and opening/closing the disc tray. Press this button to open
and close the disc tray. Pressing this button during disc playback will
cause the C 546BEE to stop playback; press again to open the disc tray.
ITALIANO
The C 546BEE can also be switched ON from standby mode by pressing
[PLAY/PAUSE/SKIP] knob on the front panel. Pressing CD 9’s [ON], [ ] or
[ ] buttons will also wake up the C 546BEE from standby mode.
5
DEUTSCH
1 STANDBY BUTTON: Press this button to switch ON the C 546BEE. The
Standby LED indicator will turn from amber to blue and illuminate the
Vacuum Fluorescent Display (VFD). Pressing the Standby button again
turns the unit back to standby mode.
4
Press [STOP/OPEN] button once to stop playback and re-set the
pickup to the beginning of the disc. The display reverts to showing
the number of tracks and total playing time on the disc; for WMA/MP3
files, the display will revert to total number of files. If the C 546BEE was
programmed to play a selection of tracks, the program will be retained
in the player’s memory. Pressing [STOP/OPEN] twice at program mode
will delete the program.
NEDERLANDS
3
Repeat and Random playback mode can be disengaged by pressing
the [STOP/OPEN] button.
Pressing the [STOP/OPEN] button will also switch ON the C 546BEE from
standby mode.
5SOURCE: Toggle this button to select through the following SOURCE
modes - CD and USB. A corresponding icon (CD or USB) will illuminate
in the VFD as the applicable SOURCE is selected or comes up during
selection.
SVENSKA
2
РУССКИЙ
1
2 STANDBY LED: This indicator will light up amber when the C 546BEE
is at standby mode. When the C 546BEE is at ON state, this indicator will
illuminate blue.
7
IDENTIFICATION OF CONTROLS
FRONT PANEL
ENGLISH
6RANDOM: This button when pressed will engage or disengage random
playback mode. When engaged (a corresponding “RANDOM” icon is
illuminated in the VFD), random playback of tracks or files will begin by
pressing [PLAY/PAUSE/SKIP] from STOP mode or rotating [PLAY/PAUSE/
SKIP] during playback mode. Press [RANDOM] again to return to normal
playback (“RANDOM” icon in the VFD is extinguished). Random playback
mode can also be disengaged by pressing [STOP/OPEN] button.
FRANÇAIS
The Random playback mode can be used in combination with the
Repeat Play All mode but not with Program playback mode.
7DISPLAY: Toggle to display the following disc information during
playback
INFORMATION
ESPAÑOL
ITALIANO
AUDIO CD
CD TEXT
MP3/WMA
Elapsed playback time of the
current track
✓
✓
-
Remaining playback time of the
current track
✓
✓
-
Running total playback time of
the disc
✓
✓
-
Remaining playback time of
the disc
✓
✓
-
Song title
-
✓
✓
Artist name
-
✓
✓
Album name
-
✓
✓
File name
-
-
✓
Elapsed time of the current file
-
-
✓
File number of the current file with
respect to the total number of files
under the current folder
-
-
✓
DEUTSCH
NOTES
• Some information may not be displayed on some discs. Display is
dependent on the disc’s information content.
• If the file has no available information about the song title, artist or
album, the display will show “NO TITLE”, “NO ARTIST” or “NO ALBUM”.
NEDERLANDS
SVENSKA
РУССКИЙ
8
8 SCAN [
]: Press and hold [
] for more than 2 seconds
to search up or down a track/file. The SCAN [
] button causes the
optical pickup to scan backwards through the recording at high speed.
The SCAN [
] button causes the optical pickup to scan rapidly
forward through the music.
9 USB INPUT: Connect a USB device into this input.
10PLAY/PAUSE/SKIP: This control knob has three functions – PLAY,
PAUSE and SKIP [
].
PLAY/PAUSE: Press this knob to toggle between Play and Pause of
a CD or other compatible media disc. Press to start play or resume
play after Pause. The icon “ ” is illuminated in the VFD indicating the
C 546BEE is in playback mode. If the disc tray is open, press this button
to automatically close the tray and start playback if a disc is loaded.
During playback, press this button to stop playback temporarily,
keeping the optical pickup at its current position on the disc. The icon
“ ” is illuminated in the VFD indicating the C 546BEE is in pause mode.
To resume playback at the exact point where it stopped, press
[PLAY/PAUSE/SKIP] again.
SKIP [
]: Rotate this knob clockwise to SKIP forward a track/
file. Rotate it counterclockwise to SKIP backward to the beginning of the
current track/file or previous track/file.
11VFD: The Vacuum Fluorescent Display (VFD) provides playback
information, settings and other indicators.
12 REMOTE SENSOR: Point the CD 9 at the remote sensor and press the
buttons. Do not expose the remote sensor of the CD 9 to a strong light
source such as direct sunlight or illumination. If you do so, you may not
be able to operate the C 546BEE with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
IDENTIFICATION OF CONTROLS
FRANÇAIS
ENGLISH
REAR PANEL
1
2
3
4
5
3 +12V TRIGGER IN: This input allows the C 546BEE to be switched
remotely to standby and ON by ancillary equipment, such as an
amplifier, preamp, AV processor, etc. The controlling device must be
equipped with a 12 V trigger output to use this feature. Connect this
+12V-trigger input to the remote component’s corresponding +12V DC
output jack using a mono cable with 3.5mm male plug.
5 AC MAINS INPUT: The C 546BEE comes supplied with a separate AC
Mains cable. Before connecting the cable to a live wall socket ensure that
it is firmly connected to the C 546BEE’s AC Mains input socket first. Always
disconnect the AC Mains cable plug from the live wall socket first, before
disconnecting the cable from the C 546BEE’s Mains input socket.
ITALIANO
2 DIGITAL OUT (COAXIAL, OPTICAL): The digital playback audio output
signal is available at these ports. Connect the optical or coaxial digital
OUT ports to the corresponding S/PDIF digital input of an amplifier,
receiver, computer soundcard or other digital processors.
4 IR IN: This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the C 546BEE from a remote location.
DEUTSCH
1 LINE OUT: Connect to the corresponding analog audio input of an
amplifier, receiver or stereo system.
ESPAÑOL
ATTENTION!
Please make all the connections to your C 546BEE with the unit unplugged. It is also advisable to power down or unplug all associated components while
making or breaking any signal or AC power connections.
РУССКИЙ
SVENSKA
NEDERLANDS
WARNING
If the male plug of the mono cable (with or without +12V DC) is
connected to C 546BEE’s +12V TRIGGER IN, the Standby button in the
front panel as well as the corresponding ON/OFF function keys in the
remote control will be disabled. Unplug the mono cable to maintain
normal power ON/OFF function procedures.
9
IDENTIFICATION OF CONTROLS
CD 9 REMOTE CONTROL
ENGLISH
ON: Switch ON C 546BEE.
OFF: Switch OFF C 546BEE.
CD: Select CD as the active source.
USB: Select USB as the active source.
OPT: Select optical input as the active source.
Not applicable for C 546BEE.
SRC: Toggle to select desired SRC mode. Not
applicable for C 546BEE.
RAND: Play tracks/files in random mode.
RPT: Repeat track, file or whole disc.
RPT A-B: Setup repeat sequence.
FRANÇAIS
FILTER: Switch between NORMAL and SLOW
bandwidth.
DISP: Show playback time and other display
information.
PROG: Enter or exit program mode.
CLEAR: Delete programmed track/file.
DIM: Reduce, turn off or restore VFD brightness.
[
]: Stop playback.
ESPAÑOL
[ ]: Pause playback temporarily.
FOLDER [ D/F ] : Select through folder lists.
FILE [ A/S ] : Select through WMA/MP3 files.
ENTER: Select desired folder or WMA/MP3 file.
SKIP [
] : Go to next track or file.
SKIP [
] : Go to beginning of current track/
file or to previous track/file.
SCAN [
]: Fast reverse/forward search.
[ ]: Start playback.
[ ]: Open or close disc tray.
ITALIANO
0 to 9 NUMBER BUTTONS: Direct-entry of
track or file number.
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
BATTERY ASSEMBLY
Press in and lift tab to remove battery cover out
of recess.
10
Press batteries into opening. Ensure correct
fitting is observed.
Replace battery cover by aligning and inserting
the two tabs into the holes. Press battery cover
into place until it “clicks” closed.
OPERATION
PROGRAMMING
The program function enables you to store your favorite tracks from any
disc in the player memory. When programming a sequence of tracks, the
C 546BEE must be in STOP mode. Using the CD 9 remote control, enter your
desired program sequence through the following steps
1 Press [PROG] button of CD 9 remote control. The display indicates “P00
T000”. The “000” in the “T000” keeps on blinking, meaning the player is
awaiting the first Program entry.
2 Use the Direct-Entry numeric keypad buttons to enter the first track in
your planned sequence. For example, press “5” to enter track number
5. Upon entering the track number, the VFD will show “P01 T005” with
“005” of “T005” blinking 3 times.
3 The display will revert to show “P02 T000”, indicating that the player is
ready for your second program entry. For example, press “8” to enter
track number 8. Upon entering the second track, the VFD will show “P02
T008” with “008” of “T008” blinking 3 times.
4 Repeat steps 2 and 3 to select and store other track numbers in
memory, up to a maximum of 40 entries. When you reach P40, the three
blinking digits will keep on flashing and won’t stop. This is unlike the
previous 39 entries wherein after an entry blinked thrice, it moves on to
the next program number/entry.
5 Press [PROG] to end or finalize the program – the VFD will show the last
programmed number and track.
6 Press [u] to start playback of the first programmed track. Rotate [PLAY/
PAUSE/SKIP] if you wish to SKIP forward/backward the programmed tracks.
If [PROG] is pressed without entering a new track/song number, the
total 40 program entries will be reduced to 39 entries. The program
sequence will adjust accordingly starting from the deleted program
number.
5 After finalizing your program changes or completing your review, press
[PROG] again.
PROGRAM PLAYBACK
1 To play the stored program, press [u] while you are in “PROGRAM”
mode. “PROG” icon will appear in the display, indicating that a stored
program is being played. During Program Play, the SKIP buttons will
access only the tracks in the program list.
2 If you want to play only a portion of a stored program, initiate play and
press SKIP to jump over the programmed tracks that you don’t want to
hear.
STOP OR DELETE PROGRAM
1 To terminate Program play, press [g] once. The stored track list remains
in memory. If you want to play the program again, simply press [u].
2 To clear the program memory, perform any of the following steps
· Press [g] twice during program playback.
· Press [k] to open the disc tray.
· Switch OFF the C 546BEE by pressing the Standby button.
· Switch to another source other than CD mode by pressing front
panel’s [SOURCE] button or [USB] source button in CD 9.
FRANÇAIS
ESPAÑOL
ITALIANO
DEUTSCH
IMPORTANT NOTICE
Customers should note that permission is required in order to download
MP3/WMA files and music from the Internet. NAD ELECTRONICS
INTERNATIONAL has no right to grant such permission. Permission
should always be sought from the copyright owner.
Example: Delete “P34 T067” from a total of 40 program entries
(display) “P34 T067” $ [CLEAR] $ (display) “P34 T000” (“000” blinking)
$ enter desired track/song number to replace T067 or press [PROG] to
finalize deletion process
NEDERLANDS
NOTES
• The file number is recognized per disc, not per folder – that is, the
number assigned to each file corresponds to their sequence in the disc.
• If you want to select file number “119” in a disc where there are 100 or
more MP3/WMA files, press “1” twice and then “9.”
• During disc playback, it is possible to select through the folder or file lists
(using [FOLDER D/F ] or [FILE A/S ] buttons) without interrupting the
current file being played back.
REVIEW/EDIT PROGRAM LIST
1 Initiate review of your programmed entries by pressing [PROG].
· If you are still in programming mode, press [PROG].
· If during program playback, press [g] once, then [PROG].
2 The VFD will show the first Program Number and the corresponding
“blinking” programmed track.
3 To change the programmed track of a particular sequence, use the
Direct-Entry numeric keypad buttons. Press [9/0] to move forward
or backward the programmed tracks as well as review the list and
change if so desired.
4 If you want to delete a particular program sequence during program
review, press [CLEAR] key.
SVENSKA
PLAYING MP3/WMA FILES
The C 546BEE can play MP3/WMA formatted recordings on CD-R or CD-RW
discs. You may mix any of the file types on the disc. Using the CD 9 remote
control, one can select through the MP3/WMA folders and files as well as
start playback through the following steps
1 Load the applicable disc.
2 Press [FOLDER D/F ] to select desired folder. Press [ENTER].
3 Press [FILE A/S ] to select desired file number. Press [ENTER] to start playback.
NOTES
· If you want to select file number “119” in a disc where there are 100 or
more MP3/WMA files, press “1” twice and then “9.”
· Pressing [g] key at any time during the programming procedure will put
to a STOP to the sequence and clear all the currently programmed tracks
or files. VFD will revert back to displaying the total number of tracks
and total playback time for audio CD and total number of files for MP3/
WMA.
· Pressing [g] key twice during program playback will result to having the
whole program list deleted.
РУССКИЙ
CD-R AND CD-RW AUDIO DISCS
The C 546BEE can play back CD-R or CD-RW audio discs that have been
recorded on a computer or CD recorder. The quality of CD-R or CD-RW
audio discs varies widely which may affect playability. Some factors that
affect playability:
• The quality of the disc itself. Generally speaking, CD-R or CD-RW blanks from
well-renowned companies give better results than unbranded ones.
• The quality of CD-recorder or computer CD re/writer. Some recorders
and writers produce better results than others.
• The CD-R and CD-RW were created with high-speed writing. In general,
the quality of a CD-R or CD-RW is better when produced at a lower
speed against a higher speed on the same recorder or re/writer.
ENGLISH
USING THE C 546BEE – CD MODE
11
OPERATION
USING THE C 546BEE – USB MODE
ENGLISH
The C 546BEE can play back MP3/WMA files stored in external USB
(Universal Serial Bus) devices. The following are the C 546BEE’s capabilities
with respect to USB device playability.
USB SUPPLEMENTARY INFORMATION
Maximum number of folders supported
Maximum file in one folder
FRANÇAIS
Maximum file in device
128
511
65408
Maximum number of sub-directory
8
Maximum number of bytes supported for Folder/File name
64
Maximum number of bytes supported for ID3 Title/Artist/Album
60
Maximum bit rate supported
VBR, 320K
HDD handling capacity (additional power adapter maybe required for
some HDD models)
FAT 16/32
ESPAÑOL
USB version supported
1.1
LISTENING TO USB DEVICE
ITALIANO
1 Toggle [SOURCE] button to select “USB” mode. If no external USB device
is connected to the front panel’s USB input, “No USB” will be displayed
in the VFD. If there are no applicable MP3/WMA files available in the
external USB, the VFD will show “USB Empty”.
2 Plug-in the external USB device to the USB input – “USB Reading” will be
blinking in the VFD and then the total number of files will displayed.
3 Press [ ] to start playback.
SELECTING DIRECTORIES OR FILES
DEUTSCH
The following are the steps on how to select a desired directory and MP3 or
WMA file at stop mode.
1 Connect the external USB device to the front panel’s USB input. Toggle
[SOURCE] button to select “USB” mode.
2 Press [FOLDER D/F ] to select desired folder. Press [ENTER].
3 Press [FILE A/S ] to select desired file number.
4 Press [ENTER] to start playback. Toggle CD 9’s [DISP] button to show
information about the current file. Refer also to the item about DISPLAY
at the FRONT PANEL section of the IDENTIFICATION OF CONTROLS page.
NEDERLANDS
NOTE
Do not disconnect the USB flash drive during playback. It may cause
damage to the C 546BEE.
SVENSKA
РУССКИЙ
12
OPERATION
DIM
Use [PROG] button to start, review, edit or exit programming mode. In
combination with [PROG] button, the [CLEAR] button allows the deletion of
a programmed track during program review or edit sequence. Refer also to
the item about “PROGRAMMING” at the “USING THE C 546BEE – CD MODE”
section of the “OPERATION” page.
FILTER
REPEAT
A particular track or file can be repeatedly played back by pressing [RPT]
button. Toggle this button to repeat a track/file, folder, all tracks or all files.
Corresponding icons like REPEAT, REPEAT FOLDER, or REPEAT ALL will
be illuminated in the VFD as the particular repeat mode is selected. Turn
off repeat mode by pressing the REPEAT button until the REPEAT icon is
extinguished in the VFD.
SVENSKA
RPT A-B
The [FILTER] button is used for selecting the bandwidth of the audio low
pass filter for the CD, MP3 and WMA media being played. The options are
NORMAL bandwidth and SLOW bandwidth. For some recordings, the SLOW
bandwidth may provide a wide frequency range and spatial feeling.
NORMAL: Select NORMAL bandwidth to engage a standard CD highpass filter slope for playback of CD, MP3, and WMA music through the
two channel stereo audio jacks.
SLOW: Select SLOW bandwidth to engage a gentle high-pass filter
slope for playback of CD music through the two channel stereo audio
jacks. This feature is particularly useful for higher bit rate recordings. A
red icon is illuminated in VFD when SLOW filter is selected.
ESPAÑOL
PROGRAM AND CLEAR
ITALIANO
Using the direct-entry numeric keypad (0 to 9) causes the C 546BEE to jump
directly to the beginning of a numbered track and commence play. Thus, to
play Track 5, simply press “5”. To play Track 20, press “2” and “0”.
Toggle to reduce, turn off and restore VFD brightness.
DEUTSCH
NUMERIC KEY PAD
FRANÇAIS
Most of the buttons on the remote control handset have the same effect as the
corresponding buttons on the front panel of the player. In addition, the handset
is equipped with some extra buttons like the following function keys.
NEDERLANDS
The CD 9 remote control is provided with your C 546BEE Compact Disc Player
to enable you to operate playback functions from the comfort of your chair or
from virtually anywhere in the room. For reliable operation, there should be a
clear line-of-sight path from the remote control to the front of the CD player. If
the player does not respond to remote commands, it may be that this line-ofsight path is obstructed by clothing, paper or furnishings.
ENGLISH
USING THE C 546BEE – CD 9 REMOTE CONTROL
РУССКИЙ
To repeat a sequence, implement the following procedures:
1 Press [RPT A-B] at your chosen starting point. “REPEAT A
B” is
illuminated in the VFD with “B” blinking.
2 Press [RPT A-B] again at your chosen end point. “REPEAT A
B” stay
illuminated. The repeat sequence begins.
3 Press [RPT A-B] again to cancel the sequence.
13
REFERENCE
TROUBLESHOOTING
ENGLISH
CONDITION
POSSIBLE CAUSES
POSSIBLE SOLUTIONS
FRANÇAIS
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is ON, but the C 546BEE does
not work.
• No disc is inserted.
• Insert a disc.
The C 546BEE does not start playback.
• The disc is loaded upside down.
• Reload the disc with the label side UP.
• The disc is too dirty.
• Clean the disc.
• The equipment connected with the audio
cable is not set to receive CD signal output.
• Select the correct input mode of the audio
receiver so you can listen to the sound from
the C 546BEE.
• The power of the equipment connected with
the audio cable is turned off.
• Turn on the equipment connected with the
audio cable.
Sound skips.
• The C 546BEE is subject to vibration or physical
shock from external sources.
• Change the installation location.
The C 546BEE cannot be switched to
standby mode.
• A mono plug is plugged-in at the +12V
TRIGGER IN port of the rear panel.
• Unplug the mono plug.
The remote control does not work properly.
• The remote control is not pointed at the
remote sensor on the CD player.
• Point the remote control at the remote
sensor of the CD player.
• The remote control is too far from the CD
player.
• Operate the remote control closer to the
CD player.
• The remote control batteries are dead.
• Replace the remote control batteries.
No sound.
ESPAÑOL
ITALIANO
NOTES ON DISCS
DEUTSCH
HANDLING DISCS
Do not touch the playback side of the disc. Hold the disc by the edges so that
fingerprints do not get on the surface. Never stick paper or tape on the disc.
NEDERLANDS
STORING DISCS
After playing, store the disc in its case. Do not expose the disc to direct
sunlight or sources of heat and never leave it in a parked car exposed to
direct sunlight.
SVENSKA
РУССКИЙ
14
CLEANING DISCS
Fingerprints and dust on the disc can cause poor picture quality and sound
distortion. Before playing, clean the disc with a clean cloth. Wipe the disc
from the center out.
Do not use strong solvents such as alcohol, benzine, thinner, commercially
available cleaners, or anti-static spray intended for older vinyl records.
REFERENCE
Output level
2.2 ± 0.2 V
Optical: -22.5 ± 3.5 dBm
Frequency response
±1 dB (ref. 0 dB 20 Hz - 16 kHz)
Coaxial: 650 ± 150 mV
Total harmonic distortion
<0.03% (ref. 0 dB 1 kHz, Audio LPF)
±0.3 dB (ref. 0 dB 20 Hz-1 kHz)
Signal/Noise ratio
118 dB
(ref. 0 dB 1 kHz, A-weighted Pause)
±0.5 dB (ref. 0 dB 5 kHz-20 kHz)
Total harmonic distortion
<0.01% (ref. 1 kHz, Audio LPF)
Signal/Noise ratio
118 dB
(ref. 1 kHz, A-weighted LPF Stop, Pause)
Channel balance
±0.5 dB (ref. 0dB 1kHz)
Dynamic range
95 dB
Channel separation
>90 dB
De-emphasis
-3.73 to -5.33 dB (ref. 0dB 1 kHz, 5 kHz)
-8.04 to -10.04 dB (ref. 0dB 1 kHz, 16 kHz)
Linearity
±0.01 dB (ref. 0dB 1 kHz at -3 dB)
±0.02 dB (ref. 0dB 1 kHz at -6 dB)
FRANÇAIS
Frequency response
USB
Analog: 2.2 ± 0.1 V
DIMENSION AND WEIGHT
Unit Dimensions (W x H x D)
435 x 306 x 89 mm (Gross)*
17 ¹/₈ x 12 ¹¹/₁₆ x 3 ⁹/₁₆ inches
Net weight
4.9 kg
10.8 lbs
Shipping weight
6.3 kg
13.9 lbs
ESPAÑOL
GENERAL PARAMETERS
Output level
ENGLISH
SPECIFICATIONS
* - Gross dimensions include feet, extended buttons and rear panel
terminals.
±0.02 dB (ref. 0dB 1 kHz at -10 dB)
ITALIANO
DEUTSCH
NEDERLANDS
<0.5W
SVENSKA
±0.15 dB (ref. 0dB 1 kHz at -60 dB)
Standby power
Specifications are subject to change without notice. For updated
documentation and features, please log onto www.NADelectronics.com for
the latest information about C 546BEE.
РУССКИЙ
±0.05 dB (ref. 0dB 1 kHz at -20 dB)
15
www.NADelectronics.com
©2016 NAD ELECTRONICS INTERNATIONAL
A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
C546BEE_eng_OM_v07 - 02/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement