Owner`s Manual • FX-1 WATER

Owner`s Manual • FX-1 WATER
FX-1 WATER
Owner‘s Manual
LIGHT EFFECT
Congratulations on your purchase of this Effect Light.
To get the most from your equipment you must read all of this manual
before using it first time.
Table of Contents
1. Safety Instruction........................................................................... 3
Rigging the fixture......................................................................... 4
2. Technical Specification.................................................................... 4
3. Description..................................................................................... 5
4. Operation...................................................................................... 5
5. Lamp installation or replacement.................................................. 5
6. Beam angle.................................................................................... 6
7. Troubleshooting............................................................................. 7
8. Fixture Cleaning............................................................................. 7
9. Disposal......................................................................................... 7
2
1. Safety Instruction
You have to read the instruction carefully, which includes
important information about the installation, operation and
maintenance.
• Please keep this User Guide for future consultation. If you sell the unit
to another user, be sure that he also receives this instruction booklet
thus giving them the necessary information about the use and general
warnings regarding the unit.
• Unpack and check carefully there is no transportation damage before
using the unit.
• Before operating, ensure that the voltage and frequency of power supply
match the power requirements of the unit as stated in this manual.
• It’s important to ground the yellow/green conductor to earth in order to
avoid electric shock.
• The unit is for indoor use only. Use it only in a dry location. Exposing
the device to rain or moisture would cause the risk of electrical shock
or fire. Maximum ambient temperature is 40°C. Don’t operate it in
locations where the temperature is higher than this.
• The unit must be installed in a location with adequate ventilation, at
least 50 cm from adjacent surfaces. Be sure that no ventilation slots are
blocked. The electrical work that is necessary for installation must done
by qualified personnel. Use safety cable when fixing this unit.
• Check the surrounding area and make sure there are no flammable liquids,
water or metal objects that could enter the fixture. If a foreign object or
substance enters the unit, immediately disconnect the mains power.
• Unit surface temperature may reach up to 85°C. Don’t touch the
housing bare-hand during its operation or shortly after. Turn off the
power and allow about 15 minutes for the unit to cool down before
replacing the bulb or serving.
• Disconnect the device from the mains power before any servicing or
maintenance.
• In the event of serious operating problem, stop using the unit
immediately. Never try to repair the unit by yourself. Repairs carried out
by unskilled people can lead to damage or malfunction. Please contact
the nearest authorized technical assistance centre. Always use the
same type spare parts.
• There are no user serviceable parts inside the fixture. Do not open the
housing or attempt any repairs by yourself. If the fixture shows any visible
damage or in the unlikely event, that your fixture may require service,
please contact your nearest dealer. Always use genuine spare parts.
3
• Do not connect the device to any dimmer pack.
• Do not look directly at the LED light beam while the fixture is on.
• Hot lamp explosion hazard. Do not open the unit within five minutes
after switching off.
• Do not start the unit without bulb enclosure or when the housing is
damaged. The housing, the lenses, or the ultraviolet filter must be
replaced if they are visibly damaged.
Rigging the fixture
• The unit should be mounted via its screw holes on the bracket. Always
ensure that the unit is firmly fixed to avoid vibration and slipping while
operating. Always ensure that the structure to which you are attaching
the unit is secure and is able to support a weight of 10 times of the
unit’s weight. Also always use a safety cable that can hold 12 times of
the weight of the unit when installing the fixture.
• Installation needs to be carried out by qualified people only. The device
should be installed out of reach of people and outside areas where
persons may walk by or be seated.
2. Technical Specification
•Power supply
Supply voltage:
Power consumption:
AC 230V 50HZ
260 W
•Fuse
Fuse: 20mm glass 250V T5A
•Bulb
ELC 24V 250W
•Dimension
328 x 266 x 144 mm
•Weight
4.5 kg
4
3. Description
1. Optical lens with manual focus adjustment.
2. Hanging bracket with 2 knobs on both sides to fasten the unit and a
mounting hole to fix a mounting hook.
3. Mains input with IEC socket and integrated fuse holder, connect the
supplied mains cable here.
4. Lamp compartment, to be opened with two screws.
5. Cooling fan.
4. Operation
• Plugging into the mains power, the fixture starts running. The Water
Wave runs in automatic mode.
• The focus is adjustable and there’s an access door allowing easy
access to the illuminant.
5. Lamp installation or replacement
• Always switch off the mains supply and never handle the lamp or the
illuminant when it is hot.
• Do not touch the bulb with bare hands. If this does happen, clean
the lamp with denatured alcohol and wipe with a lint free cloth before
installing.
• Pull the socket off the lamp. Do not pull the wires.
5
6. Beam angle
The Projector is best to be placed 5 meters away from the wall. And from
this distance the light effect will cover an area of 4 m x 4 m.
6
7. Troubleshooting
Problem
Probable cause(s)
Suggested remedy
No light
No power to the fixture
Check power connections
Blown fuse
If power is applied but does not light,
please disconnect the unit from the
mains & check / replace the fuse if
necessary.
Burned out lamp
Install new lamp.
Fixture too hot
Allow to cool down. Improve air flow
around the unit.
Electrical malfunction
Refer to service technician.
No action
8. Fixture Cleaning
The cleaning of the internal and external lenses and/or mirrors must
be carried out periodically to optimise light output. Cleaning frequency
depends on the environment in which the fixture operates: a damp, smoky
or particularly dirty surrounding can increase the accumulation of dirt on
the fixture’s optics.
• Clean with soft cloth using normal glass cleaning fluid.
• Always dry the parts carefully.
• Clean the external optics at least every 20 days. Clean the internal
optics at least every 30/60 days.
9. Disposal
Do not dispose of the device at the end of his operating life
in your normal domestic waste. This device is subject to the
European Guidelines 2002/96/EC.
• Have the product disposed of by a professional disposal company of by
your communal disposal facility.
• Observe the currently applicable regulations. In case of doubt contact
your disposal facility.
• Dispose of packaging materials in an environmentally
responsible manner.
7
© 2010
Musikhaus Thomann
Treppendorf 30 • 96138 Burgebrach
Germany • www.thomann.de
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement