LXLP10112 - Velleman
LXLP10112
LED PAR - BLACK - 18 X 9 W
USER MANUAL
LXLP10112
terminator
How to turn the controller line from 3-pins into 5-pins (plug and socket).
V. 01 – 15/01/2016
2
©Velleman nv
LXLP10112
USER MANUAL
1.
Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle
could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling. This device should be returned
to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Luxibel®! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, do not install or use it and contact your dealer.
2.
Safety Instructions
Be very careful during the installation: touching live wires can cause life-threatening
electroshocks.
Always disconnect mains power when device not in use or when servicing or
maintenance activities are performed. Handle the power cord by the plug only.
Indoor use only. Keep this device away from rain, moisture, splashing and dripping
liquids. Never put objects filled with liquids on top of or close to the device.
Keep this device away from children and unauthorized users.
Caution: device heats up during use.
Do not stare directly at the light source, as this may cause



epileptic seizure in sensitive people
temporarily loss of sight (flash blindness)
permanent (irreversible) eye damage.
There are no user-serviceable parts inside the device. Refer to an authorized dealer for
service and/or spare parts.
Respect a minimum distance of 0.5 m between the device’s light output and any
illuminated surface.
This is a Safety Class 1 device. It is therefore essential that the device be earthed.
Have a qualified person carry out the electric connection.

Make sure that the available voltage does not exceed the voltage stated in the specifications of this
manual.

Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if
necessary.
Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N).



Install the device at a minimal distance of 0.5 m from flammable and explosive objects or
substances.
The maximum ambient temperature is 40 °C. Do not operate the device at higher temperatures.
V. 01 – 15/01/2016
3
©Velleman nv
LXLP10112
3.
General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Keep this device away from dust and extreme temperatures. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm)
in front of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the
device.











Familiarise yourself with the functions of the device before actually using it. Do not allow operation
by unqualified people. Any damage that may occur will most probably be due to unprofessional use
of the device.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications
to the device is not covered by the warranty.
Only use the device for its intended purpose. All other uses may lead to short circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and
the dealer will not accept responsibility for any ensuing defects or problems.
Mechanical wear and LEDs are not covered by warranty.
A qualified technician should install and service this device.
Do not switch the device on immediately after it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room temperature.
This device is designed for professional use on stage, in discos, theatres, etc. The device should only
be used indoors with an alternating current of 110-220 V~, 50/60 Hz.
Lighting effects are not designed for permanent operation: regular operation breaks will prolong their
lives.
Use the original packaging if the device is to be transported.
Keep this manual for future reference.
4.








Features
PAR projector with high-power warm/cold white LEDs
extremely slim design
smooth dimming modes
DMX controlled via 2, 3 or 7 channels
built-in programmes
double bracket: can be used as a floor spot
clear LCD display for easy menu setting
with RDM function
5.
Overview
Refer to the illustrations on page 2 of this manual.
1
2
3
4
5
6
7
display with control buttons
3-pin XLR input and output
5-pin XLR input and output
powerCON input and output
V. 01 – 15/01/2016
4
fuse
adjustment knob
bracket
©Velleman nv
LXLP10112
6.
Installation
Choose a suitable mounting spot. Mount the device in the desired angle using the included bracket.
Connect the power cord to the mains. Disconnect after use.
6.1
Mounting the Device
 Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable
norms.












The carrying construction must be able to support 10 times the weight of the device for 1 hour
without deforming.
The installation must always be secured with a secondary attachment e.g. a safety cable.
Never stand directly below the device when it is being mounted, removed or serviced. Have a
qualified technician check the device once a year and once before you bring it into service.
Install the device in a location with few passers-by that is inaccessible to unauthorised persons.
Overhead mounting requires extensive experience: calculating workload limits, determining the
installation material to be used… Have the material and the device itself checked regularly. Do not
attempt to install the device yourself if you lack these qualifications as improper installation may
result in injuries.
For truss mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of the
(folded) bracket.
Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
Make sure there is no flammable material within a 0.5 m radius of the device.
Have a qualified electrician carry out the electric connection.
Connect the device to the mains with the power plug. All devices must be powered directly off a
grounded switched circuit. Do not connect to a dimmer pack.
The device has a power output to supply power to another device. When connecting several devices
in a daisy chain via this output, make sure that the total current does not exceed the power line’s
nominal current. Use power cables with an adequate section.
The installation has to be approved by an expert before the device is taken into service.
6.2
Connecting the Device
Power
Connect the device to the mains with the power plug.
Power all devices directly off a grounded switched circuit.
Do not connect the device to a rheostat or dimmer circuit, even when using the rheostat or dimmer
channel solely for 0 % to 100 % switching.

Have a qualified electrician carry out the electric connection.
DMX-512 Connection

When applicable, connect an XLR cable to the female XLR output of a controller (not incl.) and the
other side to the male XLR input of the device. Multiple devices can be linked through serial linking.
The linking cable shall be a dual core, screened cable with XLR input and output connectors.

A DMX terminator is recommended for installations where the DMX cable has to run a long distance
or is in an electrically noisy environment (e.g. discos). The terminator prevents corruption of the
digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω
resistor between pins 2 and 3, which is then plugged into the XLR output socket of the last device in
the chain.
7.
Operation
The device can be used in the following modes:
 stand-alone mode


master/slave
with a DMX-512 controller.
V. 01 – 15/01/2016
5
©Velleman nv
LXLP10112
7.1
Control Panel
Access the control panel functions using the four panel buttons located around the display. From left to
right:
Button
Function








MENU
UP
DOWN
ENTER
access the menu
return to a previous menu option
scroll through the menu options in ascending order
increase value
scroll through the menu options in descending order
decrease value
select menu option
store the current menu or option within the menu
Menu
Main Menu
Auto
Static
Sound
Dim mode
Back lite
Info
Address
Sub menu1
Auto-0
Auto-1
Auto-2
Auto-3
Auto-4
Fix C
Sub menu2
Speed<0~99>
<WC>
<W=XXX>
Manu C
Description
Auto Program selection
with program speed
and motor speed
setting
Static Colour selection
with colour value
<C=XXX>
Music Mode
Off
Dim1 (Fast)
Dim2 (Middle)
Dim3 (Slow)
On (Longtime)
Off (30S)
Auto test
Fix Hours
Version
LED-Temp
Address <XXX>
Sens:XX
XX 0~99
Dimmer speed
selection
Display Backlight on or
off
Select Value 1~512
Test Mode
Fixture running time
Software version
LED Temperature
DMX start address
2 CH
Channel
3 CH
See channel table
Selection of the DMX
channel mode
7 CH
M&S Md
Master
Master/slave mode
Slave
V. 01 – 15/01/2016
6
©Velleman nv
LXLP10112
Balance R<XXX>
White
Balance G<XXX>
Select Value 0~255
White Balance
Balance B<XXX>
Balance W<XXX>
Default
7.2
No
Parameter Default
Stand-Alone Mode
The device starts running in stand-alone mode after connection to the mains. This mode allows you to
use the device without controller.
1.
Connect the device to the mains to switch it on.
2.
Press MENU to enter the menu.
3.
Navigate to <Auto> or <Sound> with UP or DOWN and press ENTER to confirm.
4.
Select an option with UP or DOWN and press ENTER to confirm.
7.3
Master/Slave Mode
Notes
 The master/slave mode allows for connecting several devices to a single master device in a daisy
chain.



All slave devices will then work synchronously with the master device.
Configure all slave units before connecting the master unit to the daisy chain.
The maximum number of slave units you can connect to a master unit is 18.
Slave units:
1.
Connect the DMX input from your slave device to the DMX output of the previous device in the
chain.
2.
Connect the slave device to the mains to switch it on.
3.
Repeat these steps for all slave units.
Master unit
1.
Connect the master device to the mains to switch it on.
2.
Set the master unit to work in one of the running modes.
3.
Connect the master unit as the first unit in the chain by connecting the DMX output of the master
device to the DMX input of the first slave unit.
7.4
DMX Mode
The DMX mode allows you to control the device with any universal DMX controller.

All DMX-controlled devices need a digital start address so that the correct device responds to the
signals. This digital start address is the channel number from which the device starts to “listen” to
the DMX controller. The same starting address can be used for a whole group of devices or an
individual address can be set for every device.

When all devices have the same address, all the units will “listen” to the control signal on one
particular channel. In other words: changing the settings of one channel will affect all devices
simultaneously. If you set individual addresses, each device will “listen” to a separate channel
number. Changing the settings of one channel will only affect the device in question.
To set the device to work with a DMX controller:
1.
Press MENU, select a channel mode and press ENTER.
2.
Use UP and DOWN to set the DMX start address and press ENTER.
V. 01 – 15/01/2016
7
©Velleman nv
LXLP10112
Start addresses
Use the table below to define the correct address. The table shows the settings for units 1 to 3. Apply the
same principle for the other units. Example:
channel mode
2
start address
channel
1st unit
1
1-2
2nd unit
3 (1 + 2)
3-4
3rd unit
5 (3 + 2)
5-6
highest start address
511
DMX Channel Values
2-channel mode
channel
1
2
from
000
000
to
255
255
function
warm
cool
from 0-100 %
from 0-100 %
description
to
255
255
255
function
dimmer
warm
cool
from 0-100 %
from 0-100 %
from 0-100 %
from
000
000
000
000
011
000
052
102
153
204
to
255
255
255
010
255
051
101
152
203
254
function
dimmer
warm
cool
255
255
000
000
052
102
153
204
255
051
101
152
203
255
3-channel mode
channel
1
2
3
from
000
000
000
description
7-channel mode
channel
1
2
3
4
5
6
7
8.
strobe
auto
programme
speed
dimmer
speed
description
from 0-100 %
from 0-100 %
from 0-100 %
no function
from 0-20 Hz
no function
auto programme 1: colour fade 0-100-0 %
auto programme 2: colour fade 0-100 %
auto programme 3: colour fade 100-0 %
auto programme 4: colour macro, fade
auto programme 5: loop running the above
programmes
auto programme: slow > fast
preset dimmer speed from control panel
dimmer mode off
dimmer speed 1: fast
dimmer speed 2: middle
dimmer speed 3: slow
Cleaning and Maintenance
Before starting any cleaning or maintenance activities:
1.
2.
Unplug the device's power cord from the outlet.
Let the device cool down.
Cleaning






Make sure to empty the tank before cleaning.
Use normal glass cleaner and a soft cloth to wipe off the outside casing.
Clean the external optics with glass cleaner and a soft cloth every 20 days.
Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the unit operates (i.e. smoke, fog residue,
dust, dew).
Do not immerse the device in any liquid.
V. 01 – 15/01/2016
8
©Velleman nv
LXLP10112
Maintenance






All screws should be tightened and free of corrosion.
The housing, the lenses, the mounting supports and the installation location (e.g. ceiling, suspension,
trussing) should not be deformed, modified or tampered with; e.g. do not drill extra holes in
mounting supports, do not change the location of the connections…
Mechanically moving parts must not show any signs of wear and tear.
The electric power supply cables must not show any damage. Have a qualified technician maintain
the device.
There are no user-serviceable parts, apart from the fuse and the lamp.
Refer to an authorized dealer for service and/or spare parts.
8.2
1.
2.
3.
4.
5.
6.
9.
Replacing the fuse
Unplug the device's power cord from the outlet.
Let the device cool down.
Remove the rear cover with a flat-head screwdriver.
Open the fuse holder.
Replace with an appropriate fuse.
Insert the fuse holder back in its place, replace the rear cover and reconnect power.
Technical Specifications
power supply ......................................................................... 110-220 V~, 50/60 Hz
current ................................................................................................ 0.45-0.98 A
power consumption .......................................................................................150 W
LED drive current ........................................................................................ 500 mA
LEDs ................................................................................ 18 x 9 W CW 2-in-1 LEDs
dimming level ........................................................................................... 0-100 %
dimming frequency .................................................................................... 1200 Hz
signal connector ....................................................... XLR 3-pin or 5-pin input/output
power connector ..................................................................................... powerCON
IP rating ........................................................................................................ IP20
lifetime ..................................................................................................... 50000 h
dimensions ......................................................................... 30.2 x 31.36 x 13.09 cm
weight ......................................................................................................... 5.9 kg
Use this device with original accessories only. Velleman nv cannot be held responsible in the
event of damage or injury resulting from (incorrect) use of this device. For more info
concerning this product and the latest version of this manual, please visit our website
www.luxibel.com. The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part
of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise
without the prior written consent of the copyright holder.
V. 01 – 15/01/2016
9
©Velleman nv
Velleman® Service and Quality Warranty
Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world
and currently distributes its products in over 85 countries.
All our products fulfil strict quality requirements and legal stipulations in the EU. In order to
ensure the quality, our products regularly go through an extra quality check, both by an
internal quality department and by specialized external organisations. If, all precautionary
measures notwithstanding, problems should occur, please make appeal to our warranty (see
guarantee conditions).
General Warranty Conditions Concerning Consumer Products (for EU):
• All consumer products are subject to a 24-month warranty on production flaws and defective
material as from the original date of purchase.
• Velleman® can decide to replace an article with an equivalent article, or to refund the retail
value totally or partially when the complaint is valid and a free repair or replacement of the
article is impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of 100% of the purchase price
in case of a flaw occurred in the first year after the date of purchase and delivery, or a
replacing article at 50% of the purchase price or a refund at the value of 50% of the retail
value in case of a flaw occurred in the second year after the date of purchase and delivery.
• Not covered by warranty:
- all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks,
falls, dust, dirt, humidity...), and by the article, as well as its contents (e.g. data loss),
compensation for loss of profits;
- consumable goods, parts or accessories that are subject to an aging process during normal
use, such as batteries (rechargeable, non-rechargeable, built-in or replaceable), lamps, rubber
parts, drive belts... (unlimited list);
- flaws resulting from fire, water damage, lightning, accident, natural disaster, etc.…;
- flaws caused deliberately, negligently or resulting from improper handling, negligent
maintenance, abusive use or use contrary to the manufacturer’s instructions;
- damage caused by a commercial, professional or collective use of the article (the warranty
validity will be reduced to six (6) months when the article is used professionally);
- damage resulting from an inappropriate packing and shipping of the article;
- all damage caused by modification, repair or alteration performed by a third party without
written permission by Velleman®.
• Articles to be repaired must be delivered to your Velleman® dealer, solidly packed
(preferably in the original packaging), and be completed with the original receipt of purchase
and a clear flaw description.
• Hint: In order to save on cost and time, please reread the manual and check if the flaw is
caused by obvious causes prior to presenting the article for repair. Note that returning a nondefective article can also involve handling costs.
• Repairs occurring after warranty expiration are subject to shipping costs.
• The above conditions are without prejudice to all commercial warranties.
The above enumeration is subject to modification according to the article
(see article’s manual).
Made in PRC
Imported by Velleman nv
Legen Heirweg 33, 9890 Gavere, Belgium
www.velleman.eu
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising