In-circuit debugger/programmer for STM8 and

In-circuit debugger/programmer for STM8 and
ST-LINK
In-circuit debugger/programmer for STM8 and STM32
Data brief
Features
■
5 V power supplied by USB connector
■
USB 2.0 full speed interface compatible
■
USB standard A to Mini-B cable provided
■
SWIM specific features:
– 1.65 V to 5.5 V application voltage
supported on SWIM interface
– SWIM low speed and high speed modes
supported
– SWIM programming speed rates of
9.7 Kbytes/s in low speed, 12.8 Kbytes/s in
high speed
– SWIM cable for connection to an
application with an ERNI standard
connector vertical (ref: 284697 or 214017)
or horizontal (ref: 214012)
– SWIM cable for connection to an
application with pin headers or 2.54 mm
pitch connector
■
JTAG/SWD specific features:
– 3 V to 3.6 V application voltage supported
on JTAG/SWD interface and 5 V tolerant
inputs
– JTAG/SWD cable provided for connection
to a standard JTAG 20-pin pitch 2.54 mm
connector
■
Direct firmware update feature supported
■
Status LED which blinks during communication
with PC
■
Operating temperature 0 to 50 °C
Table 1.
ST-LINK
January 2012
The ST-LINK is an in-circuit debugger and
programmer for the STM8 and STM32
microcontroller families. The SWIM and
JTAG/SWD interface is used to communicate with
the STM8 or STM32 microcontroller located on
your own application board.
STM8 applications use the USB full speed
interface to communicate with
STMicroelectronics’ ST Visual Develop (STVD) or
ST Visual Program (STVP) software.
Device summary
Order code
Description
Reference
ST-LINK in-circuit debugger
and programmer for the STM8
and STM32
STM32 applications use the USB full speed
interface to communicate with ATOLLIC®, IAR™,
KEIL™ or TASKING™ integrated development
environments.
Doc ID 17823 Rev 2
For further information contact your local STMicroelectronics sales office.
1/3
www.st.com
3
Revision history
1
ST-LINK
Revision history
Table 2.
2/3
Document revision history
Date
Revision
Changes
20-Aug-2010
1
Initial release.
06-Jan-2012
2
Added TASKING to list of integrated development environments.
Doc ID 17823 Rev 2
ST-LINK
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 17823 Rev 2
3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement