S I M P L Y A M A Z I N G ®

U

SER

’

S

G

UIDE

COMMERCIAL

XL2070RHSM

HIGH SPEED UPRIGHT VACUUM

CLEANER WITH

®

CLEANING SYSTEM

•IMPORTANT•

SAVE THIS BOOKLET!

Includes:

• Safety Warnings

• Warranty

• Operating Instructions

• Trouble Diagnosis

• Accessories

BEFORE OPERATING

CLEANER, READ ALL

INSTRUCTIONS IN THIS

MANUAL CAREFULLY.

T

able of

C

ontents

Maintenance and Customer Service,

Accessories, Important Safety

Instructions . . . . . . . . . . . . . . . . . . . . page 2

Warranty,

Troubleshooting Guide . . . . . . . . . . . page 3

Assembly,

Operating Instructions . . . . . . . . . . . . page 4

Operating Instructions cont.,

To Replace Filter Dust Bag . . . . . . . . page 5

How to Replace a Worn Belt,

Stuffing or Blockage . . . . . . . . . . . . . page 6

Using an ORECK Fresh Air

®

Tab,

Grounding Instructions,

To Adjust or Replace Brush . . . . . . . . page 7

M

aintenance and

C

ustomer

S

ervice

Your ORECK vacuum cleaner is a product of precise engineering.

The motor bearings are permanently lubricated and should not be oiled. If you require additional information or have problems with your ORECK appliance, you may call ORECK commercial customer service at:

Commercial 1 800 242-1378

Hospitality 1 888 23-ORECK

Canada 1-866-74-ORECK

Please specify the model number and serial/code number which can be found on the data plate on the back of the vacuum.

Save your sales or purchase slip. Should your ORECK appliance require warranty service in the U.S.A., present this slip to the

Authorized Service Center as your proof of purchase date or, in

Canada, call customer service.

A

ccessories

Sold Separately

Commercial: 1-800-242-1378 Hospitality: 1-888-23-ORECK

Canada: 1-866-74-ORECK

ITEM PART #

1.

Dust Bag, 25 Pack, Saniseal ®

ACDS Hypo-Allergenic PK800025DW

Dust Bag, 25 Pack, Regular

2.

Belts, 3 Pack

3.

Oreck Fresh Air ® Tabs

PK800025

0300604

AIRTABS

IMPORTANT

SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER

WARNING

To reduce the risk of fire, electric shock, or injury:

• Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• Do not operate the unit while in the upright and locked position.

• Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or call customer service at: Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-866-746-7325

• Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.

• Do not run appliance over cord.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

• Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Do not use without filter bag assembly in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible liquids, such as gasoline or lighter fluid, or use in areas where they may be present.

• Do not use appliance in an enclosed space where flammable, explosive or toxic vapors are given off by oil base paint, paint thinner, some mothproofing substances, or in an area where flammable dust is present.

• Do not pick up toxic material such as chlorine bleach, drain cleaner, gasoline, etc. with this appliance.

• Use caution when vacuuming over area rug edges and fringe.

SAVE THESE INSTRUCTIONS

For Commercial Use

2

W

arranty

ORECK MANUFACTURING COMPANY: (Oreck gives you the following limited warranty for this product only if it was originally purchased for use, not resale, from Oreck or an Oreck Authorized

Retail Dealer.)

Oreck will repair or replace, free of charge, to the original purchaser, any part which is found to be defective in material or workmanship within six (6) months of the date of purchase. This limited warranty covers the revolving roller brush for thirty (30) days for commercial use only.

This limited warranty does not cover the replacement of expendable or consumable parts such as carbon motor brushes, edge brushes, drive belts, bulbs, disposable bags and other parts subject to normal wear unless they are defective in material or workmanship.

This limited warranty does not apply to any part subjected to accident, abuse, or alteration, misuse, damage caused by fire or act of God, the use of voltages other than indicated on the serial number plate of this product or service of this product by other than

Oreck or an Oreck Factory Authorized Service Center.

Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product.

Oreck’s limited warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product. If you purchase this product from any other source, your purchase is “AS IS,” which means Oreck grants you no warranty, and that you, not Oreck, assume the entire risk of the quality and performance of this product, including the entire cost of any necessary servicing or repairs of any defects.

Oreck’s liability for damages to you for any costs whatsoever arising out of this statement of limited warranty shall be limited to the amount paid for this product at the time of original purchase, and Oreck shall not be liable for any direct, indirect, consequential or incidental damages arising out of the use or inability to use this product.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,

INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN

DURATION TO THE WARRANTY PERIOD, AND NO

WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY

AFTER THIS PERIOD.

Some states do not allow limitations on the duration of implied warranties, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

T

roubleshooting

G

uide

WARNING: Unplug cord from electrical outlet before servicing.

SAVE SERVICE CALLS...CHECK THESE FIRST:

• Is the disposable filter dust bag full?

• Are pores of filter dust bag clogged with powder or fine dust?

• Is anything clogging the revolving brush, lower tube, intake opening, fan housing or connector assembly opening?

• Is the belt in place and turning the brush?

• Are the brush ends in the proper location?

• Does the brush turn freely? Are hair, string or rug fibers wound around the brush?

P

ROBLEM

C

LEANER

WILL NOT RUN

P

OSSIBLE

S

OURCE

A

REAS TO

C

HECK

Not plugged in properly.

Be sure cleaner is firmly plugged into wall outlet.

No electricity in wall outlet.

C

LEANER

DOES NOT PICK UP

Filter bag is full.

Check electrical source–fuse or circuit breaker.

Replace filter bag.

See “To Replace

Paper Filter Dust

Bag.”

Nozzle or intake pivot clogged.

Belt is broken or stretched.

Brush is worn.

Clear obstruction.

Replace belt.

See “To Adjust or

Replace Brush”

Bag tube clogged.

Clear obstruction.

Bag pores are clogged with fine dust.

Impeller fan is broken.

Change bag

Revolving brush is not even at both ends.

Return to Service

Center for repair.

Check brush roll end cards. Make sure words “old” or “new” match at each end.

ALL OTHER SERVICING SHOULD BE DONE BY AN

ORECK AUTHORIZED SERVICE CENTER.

CALL COMMERCIAL CUSTOMER SERVICE HOT LINE

Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-866-746-7325

Whenever calling, please be sure to have your model and serial number from data plate.

3

To assist you in identifying components of your vacuum, the parts have been numbered as follows:

10

11

9

1

4

8

3

7

12

13

2

14

1

1 Handle section, upper

2 Tube, lower

3 Power head

4 Outer bag

5 Paper filter dust bag

6 Power cord

7 Retaining spring

8 Bag tension bar

9 Zip fastener

10 On/off switch

11 Cord hook

12 Plastic loop/ cable clamp

13 Connector assembly

14 Fan housing

15 Cord assembly

16 Handle Brace

5

Before assembling appliance, remove two screws from the connector assembly. Remove cardboard insert by pulling upward.

15

16

6

2

3

Upper

Handle

A

Connector

Assembly

ssembly

With ON/OFF switch facing the front of the unit, slide upper handle section over matching section of the connector assembly.

Place brace against handle and connector assembly aligning screw holes. Insert short screw into top hole and long screw into the bottom hole then tighten firmly until handle is no longer loose.

Attach cord to cord clip by pressing cord above and below clip ensuring the cord is fully rested in clip.

O

perating

I

nstructions

To Operate

Make sure disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet and press the On (l) - OFF (O) switch on Helping Handle Assembly, or on top of base for Straight

Handle Models when ready to operate.

General Information

The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service, read the instructions and keep them handy for future reference.

Operating Recommendations

This new ORECK XL High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use.

The following are a few simple suggestions regarding its operation:

1. When inserting a new disposable paper filter dust bag—

FIRST PUFF OUT and OPEN THE BAG.

2. When the disposable filter dust bag is full, REPLACE IT.

3. If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.

4. Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing.

5. WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty.

6. REPLACE THE BELT EVERY 6 MONTHS.

7. Change the disposable filter dust bag at least once a month—even if it is not full! The collected dust in the dust filter can cause odor, attract moisture, act as a breeding area and can affect the efficiency of the cleaner.

8. DO NOT run the vacuum cleaner over the cord. The revolving brush could damage the cord.

9. Use caution when vacuuming over area rug edges and fringe.

Disposable Paper Filter Dust Bags

Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the filter bag is to trap dirt, but at the same time it must be porous enough to allow air to pass through. If the filter bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner’s power.

To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE

INDICATED ON THE DUST BAG.

Be sure the disposable paper filter dust bag is installed properly.

4

All paper dust bags are not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner. Using bags other than genuine ORECK disposable bags will affect the cleaning ability of your cleaner and could cause damage to it.

The Belt

The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the revolving brush to stop completely or slow down. See instructions in the manual for replacing belt.

An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use ONLY ORECK genuine belts. Belts other than ORECK belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings. Using belts other than ORECK belts will void the warranty.

Lubrication

The vacuum cleaner motor bearings are factory lubricated and sealed. Further lubrication is not required.

General Cleaner Care

At least once a month, check for and remove excessive lint, string or hair from the revolving brush.

Wipe the outside of the cleaner with a damp cloth. Also, clean the connector deflector assembly area, base of cleaner and fan housing area. If there is dust in the outer bag, vacuum it or shake it out.

A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness.

CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.)

Floor Surfaces and Polished Floor Finishes

Use floor and floor finish manufacturer’s recommended methods of cleaning. The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive surfaces, and, therefore, cause damage to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished floor finishes. The roller brush may also scuff very soft finishes. Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.

B

A

T

o

R

eplace

F

ilter

D

ust

B

ag

WARNING: Unplug cord from electrical outlet before servicing.

BAG INSTALLATION:

1. Hook bottom of bag collar opening under lip “B” of connector assembly. Pull up on bag collar and snap over lip “A” of connector.

2. Press on edges of bag collar to insure bag is completely installed.

IMPORTANT: Check to make sure bag collar is behind lips “A” and “B”. If it is not, dust will leak into outer bag. When filter bag is in place, close outer bag with zipper fastener.

5

H

ow to

R

eplace a

W

orn

B

elt

WARNING: Unplug cord from electrical outlet before servicing.

Remove the replacement belt from the storage channel.

Remove the door by removing the hold down screw located on side of power head.

Slide the door forward by prying open with a screwdriver or coin.

Remove the belt from the brush roll pulley and the motor drive shaft.

Loop the new belt over the motor drive shaft.

Place the opposite end of the belt on the brush roll pulley.

Rotate the brush roll three

(3) complete revolutions to ensure that no part of the belt is overhanging the end of the motor drive shaft.

Replace the door by sliding it into the groove at the bottom of the housing. Replace the hold down screw.

S

tuffing or

B

lockage

Under certain conditions, it is possible to stuff or block the intake tube and the lower tube assembly. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up or balloon open, follow the following steps:

WARNING: Unplug cord from electrical outlet before servicing.

A

B

Retainer

C

D

Spring

O-ring

Intake Opening

Intake Opening

Fan

Housing

1. Check for blockage at the mouth of the intake opening. See illustration A.

If there is blockage, remove it with long-nose pliers, a screwdriver or coat hanger.

If you can not reach the blockage, remove baseplate. See illustration B.

2. If the blockage is not at the base, remove lower tube.

See illustration C. Unhook retainer spring, releasing bottom of bag. Twist lower collar counterclockwise to slide up. Pull tube out of base. Check for blockage. If blockage is in the tube, remove with a coat hanger.

3. If tube is not blocked, look into fan housing. See illustration D. Remove debris with long-nose pliers, a screwdriver or coat hanger.

4. To reassemble, check O-ring on tube, and replace if damaged. Vacuum will not operate properly without the tube O-ring. Slide O-ring to approximately 2" from base of tube. Replace tube by first lining up slot at base of tube with inner tab inside fan housing. Then reinsert tube and push down until the tube is seated. Make sure O-ring is in place against fan housing opening. Replace and tighten collar until collar locking tabs are locked in place. See illustration E.

Make sure collar is not cross threaded on housing.

E

6

5. Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system. When that happens, the blockage will be at the top of the system, starting in the area where the dust bag connects to the connector assembly.

See illustration F.

F

Connector

Deflector

Opening

NOTE: If the above actions do not correct the problem, contact an ORECK authorized service center or call the commercial customer service center.

Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK Canada: 1-866-746-7325

IMPORTANT: On plush and new carpets, stuffing may occur due to excessive fuzz and loose cuttings in the carpet.

Stuffing could occur for the first few cleanings until all the loose material is removed. Due to the high efficiency of the cleaner, many older carpets will cause stuffing when the cleaner is first used on them.

Using an Oreck

Fresh Air Tab

Your ORECK XL vacuum cleaner has a special Oreck Fresh Air ® tab pocket.

This pocket is located inside the outer bag in the area where the paper disposable bag attaches to the intake tube. Insert tablet in pocket.

Grounding Instructions

This appliance must be grounded. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electric shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an electrical outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is grounded. If not, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit. It has a grounding plug similar to the example shown. Make sure the appliance is connected to an outlet with the same configuration as the plug. No adapter should be used with this appliance.

Grounding Pin

Grounded Outlet

7

T

o

A

djust or

R

eplace

B

rush

WARNING: Unplug cord from electrical outlet before servicing.

To determine if the brush is worn, place a firm straight edge across the nozzle opening. If brush bristles do not extend beyond baseplate, brush should be adjusted.

Rotate and match bearing assemblies

Remove the baseplate by removing 5 screws. Then, remove the belt and brush roll from the housing.

Rotate both bearing assemblies at ends of brush roll to show “old” and replace in the holding channels in the housing.

NOTE: The bearing assembly setting marked

“OLD” has a smooth side on the end card. The one marked “NEW” has a notched side on the end card. When rotating bearings, make sure both bearing assembly settings are the same and face up when replacing the brush roll.

IMPORTANT: Unless the brush is worn, as indicated above, both bearings must be in the “new” position. When rotating, both bearings must be in the “old” position.

Unmatched settings will cause damage to your machine.

Reassemble the belt and the baseplate and check bristle height above baseplate at each end of brush.

If a previous adjustment has already been made and bristle height does not extend above baseplate, a new brush assembly should be ordered.

75628-03 REV B ©2005 Oreck Holdings, LLC. All Rights Reserved.All word marks, logos, product configurations, and registered tradmarks are owned and

05/05 ECN# R-8018 used under the authority of Oreck Holdings, LLC. Printed in America