Oregon Scientific | BPW810N | User's Manual | Oregon Scientific BPW810N User's Manual

•
1. Wrist cuff
2. Battery compartment
•
LCD SYMBOLS
Talking Blood Pressure Monitor
Model: BPW810N
•
SYMBOL
USER MANUAL
EN
INTRODUCTION
Thank you for selecting the Oregon Scientific TalkingWrist
Type Blood Pressure Monitor (BPW810N). The (BPW810N)
features voice announcement and playback of blood
pressure measurements for added convenience and has been
designed to provide you with many years of reliable service.
The unit can help you measure and track the following metrics:
•
Systolic pressure
•
Diastolic pressure
•
Mean arterial pressure
•
Pulse rate
•
Historic record of up to 30 measurements per user
(maximum 2 users)
TM
Readings taken by the blood pressure monitor are
equivalent to those obtained by a trained observer using
the cuff and stethoscope auscultation method. Clinical
performance were successfully done against ANSI/
AAMI SP10 and international protocol, and the B.H.S.
(British Hypertension Society) has rated this product
“recommended for clinical and home use”, the highest
grading available for blood pressure monitors.
Please refer to BHS website http://www.bhsoc.org/bp_
monitors/automatic_wrist.stm
DESCRIPTION
EXPLANATION
Systolic pressure
The highest blood
pressure measured
Diastolic pressure
The lowest blood
pressure measured
Time (hour: minutes)
Current time
Mean arterial
pressure
Average blood
pressure measured
(see “What is Mean
Arterial Pressure
(MAP)?” for more
information)
kPa
•
•
Shows which user
profile (1 or 2 is
being displayed)
What is blood pressure?
If “MEM” shows,
the displayed
measurement value
is from the memory
and not necessarily
from the last reading
(e.g., the pumping action of the
ABOUT BLOOD PRESSURE
Blood pressure is the force genera
walls of arteries during cardiac co
What are systolic pressure an
When ventricles contract and pu
blood pressure reaches its max
pressure in the cycle is known a
the heart relaxes between hea
pressure is diastolic pressure.
Weak battery
Batteries are low and
need to be replaced
Inflating
Unit is inflating
with air to obtain
the needed level of
pressure
Deflating
Wrist cuff air is
exhausting or
deflating
Millimeter(s) of
mercury
Measurement unit
for blood pressure
The mean arterial pressure
pressure that forces blood thro
the average of the systolic and
rather, MAP corresponds to a sta
compressive and expansive for
wall when there is no distension
an excellent way to evaluate the
blood vessels, and can be used
on the cardiovascular system. S
your doctor to provide additional
him or her understand your situa
Kilopascal
Measurement unit
for blood pressure
Why measure your blood pres
4
2
•
User
Read the manual thoroughly before using the product.
1
•
Pulse rate per
minute
This manual contains important safety and care information,
and provides step-by-step instructions for using the product.
FRONT VIEW
•
Pulse
Memory
KEY FEATURES
•
Do not immerse the unit in w
with water, dry it immediately
Use a soft, slightly moistene
and cuff. Do not use abras
agents, as these may cause
Remove the batteries when
store the unit for a long peri
When replacing batteries,
specified in this user manua
batteries.
Do not place objects such a
or unit, as these may impair
Do not subject the unit to ex
temperature changes, or h
may result in malfunction,
span, damaged batteries, o
Do not tamper with the int
so will terminate the produc
damage.
The unit contains no user- s
If you no longer need to us
environment by bringing it to
collection point for proper di
Voice activation
5
Voice announcing
your blood pressure
measured
6
SAFETY AND CARE INSTRUCTIONS
What is mean arterial pressur
Blood pressure measurement
health condition. High blood pre
to serious illnesses such as s
kidney failure.
Since there is no symptom
hypertensive people do not rea
their health is seriously threaten
7
1.
2.
3.
4.
5.
6.
7.
TALK / VOLUME button
LCD
ON / OFF button
Speaker
USER 1 / UP ARROW button
USER 2 / DOWN ARROW button
SET button
REAR VIEW
Please observe the following safety precautions when
setting up and using your blood pressure monitor.
•
This device is intended for adult use only.
•
This device is intended for non-invasive measuring
and monitoring of arterial blood pressure. It is not
intended for use on extremities other than the wrist
or for functions other than obtaining a blood pressure
measurement.
•
Do not confuse self-monitoring with self-diagnosis.
This unit allows you to monitor your blood pressure.
Do not begin or end medical treatment based solely on
the measurements of this device. Consult a physician
for treatment advice.
•
If you are taking medication, consult your physician
to determine the most appropriate time to measure
your blood pressure. Never change a prescribed
medication without consulting your physician.
•
This unit is not suitable for continuous monitoring
during medical emergencies or operations.
•
If the cuff pressure exceeds 40 kPa (300 mmHg),
the unit will automatically deflate. Should the cuff not
deflate when pressures exceeds 40 kPa (300mmHg),
button
detach the cuff from the wrist and press the
to stop inflation.
•
To avoid measurement errors, carefully read this
manual before using the product.
What is the standard blood pr
Figure 3 illustrates the blood Pre
by World Health Organization
Society of Hypertension (ISH) in
Diastolic blood pressure (mmHg)
SAFETY PRECAUTIONS
3
Grade 3 hyperten
110
100
95
90
85
80
Grade 2 hypertension
Grade 1 hypertension(mil
Subgroup: borderline
High-normal Blood Pressure
Normal Blood Pressure
Optimal Blood
Pressure
120
130
140
Systolic blood pres
Reference material: 1999 Wo
International Society of Hypert
management of hypertension,
1999, 17(2): 151-183.
NOTE
CARING FOR YOUR BLOOD PRESSURE MONITOR
•
To ensure you receive the maximum benefit from using
this product, please observe the following care guidelines.
•
When not in use, store the unit in a dry place away
from direct sunlight.
•
Blood pressure is conside
diastolic or systolic blood pr
normal range. When a patie
blood pressures fall into
higher category should appl
Only a physician can tell
pressure range and the poin
•
•
•
PTION
EXPLANATION
ssure
The highest blood
pressure measured
essure
The lowest blood
pressure measured
minutes)
Current time
al
Average blood
pressure measured
(see “What is Mean
Arterial Pressure
(MAP)?” for more
information)
Pulse rate per
minute
•
•
•
If “MEM” shows,
the displayed
measurement value
is from the memory
and not necessarily
from the last reading
(e.g., the pumping action of the heart).
Batteries are low and
need to be replaced
Blood pressure is the force generated by the blood against the
walls of arteries during cardiac contraction and relaxation
What are systolic pressure and diastolic pressure?
When ventricles contract and pump blood out of the heart,
blood pressure reaches its maximum value. This highest
pressure in the cycle is known as systolic pressure. When
the heart relaxes between heartbeats, the lowest blood
pressure is diastolic pressure.
What is mean arterial pressure (MAP)?
Measurement unit
for blood pressure
The mean arterial pressure (MAP) is the average
pressure that forces blood through the arteries. It is not
the average of the systolic and diastolic blood pressure;
rather, MAP corresponds to a state of balance between the
compressive and expansive forces acting on the arterial
wall when there is no distension outward or inward. MAP is
an excellent way to evaluate the stress on the walls of your
blood vessels, and can be used to evaluate excessive load
on the cardiovascular system. Show your MAP history to
your doctor to provide additional information that may help
him or her understand your situation.
Measurement unit
for blood pressure
Why measure your blood pressure?
Voice announcing
your blood pressure
measured
NSTRUCTIONS
NS
owing safety precautions when
blood pressure monitor.
ed for adult use only.
ded for non-invasive measuring
rterial blood pressure. It is not
extremities other than the wrist
than obtaining a blood pressure
-monitoring with self-diagnosis.
to monitor your blood pressure.
medical treatment based solely on
this device. Consult a physician
dication, consult your physician
st appropriate time to measure
e. Never change a prescribed
onsulting your physician.
able for continuous monitoring
gencies or operations.
exceeds 40 kPa (300 mmHg),
cally deflate. Should the cuff not
es exceeds 40 kPa (300mmHg),
button
he wrist and press the
ment errors, carefully read this
the product.
OOD PRESSURE MONITOR
Consult your physician to obtain these values. If the
measurements taken with these products fall outside
the range, consult your physician.
Why does my blood pressure fluctuate throughout the day?
Individual blood pressure varies greatly both on a daily and
a seasonal or temperature basis. These variations may be
more pronounced in hypertensive patients. Normally the
blood pressure rises while at work and is at its lowest
during sleep.
The graph below illustrates the variations over a single day
with measurement taken every 5 minutes. The thick line
represents sleep time. The rises in blood pressure at 4PM
(A in the graph) and 12AM (Bin the graph) correspond to
an attack of pain and sexual intercourse (Beven, Honour &
Stott, Clin. Sci. 36:329, 1969).
4.
5.
Press SET to accept the cha
setting.
When you are finished, press
POSITIONING THE WRIST C
It is important to properly positio
that you receive an accurate rea
1.
2.
3.
4.
5.
Remove all accessories (w
your left wrist. If your physici
poor circulation in your left a
Roll or push up your sleeve
Apply the cuff to your left wris
Position the edge of the cu
from the bottom of your palm
Fasten the wrist cuff aroun
extra room between the cuf
is too loose, the measureme
HOW THE BLOOD PRESSURE MONITOR WORKS
This product uses the Oscillometric Measuring method to
detect your blood pressure. Before every measurement,
the unit establishes a “zero pressure”equivalent to the air
pressure.
Then it starts inflating the wrist cuff to 180mmHg or higher
until it senses that it has blocked your blood in the artery.
After that, the deflation process starts, during which time
the unit detects pressure oscillations generated by beatto-beat pulsatile, which is used to determine the systolic,
mean and diastolic pressure, and also your pulse rate.
Any motion during this period will result in an incorrect
measurement. After all readings are determined and
displayed on the LCD, the measurement is finished and
the wrist cuff automatically deflates.
GETTING STARTED
INSTALLING AND REPLACING THE BATTERIES
1.
2.
3.
Slide off the battery cover.
Install the batteries by matching the correct polarity, as
shown below. Always use the correct battery type (2
alkaline LR03 AAA-size).
Replace the cover.
NOTE Graphics may not exac
VOICE PLAYBACK OF BLOO
MEASUREMENTS
The BPW810N features voice play
pressure measurement result
instructions to help you prepare
When the unit has finished ta
your blood pressure readings,
classification are announced.
If you want to repeat the ann
TALK / VOLUME.
Blood pressure measurement can highly reflect one’s
health condition. High blood pressure is potentially linked
to serious illnesses such as stroke, heart disease and
kidney failure.
Anytime you recall a measurem
it will also be announced. Press
need to repeat the playback of a
Since there is no symptom most of the time, many
hypertensive people do not realize they are at risk until
their health is seriously threatened.
VOLUME CONTROL
To adjust the volume level:
1. Press and hold TALK / VO
flashes on the LCD.
2. Press TALK / VOLUME to a
What is the standard blood pressure classification?
Figure 3 illustrates the blood Pressure classification made
by World Health Organization (WHO) and International
Society of Hypertension (ISH) in 1999.
Grade 3 hypertension(severe)
110
100
95
90
85
80
Grade 2 hypertension(moderate)
Grade 1 hypertension(mild)
Subgroup: borderline
NOTE Replace the batteries whenever the weak battery
shows, the display is dim, or the display does not
mark
illuminate when the power is on. Replace all the batteries
at the same time - it is dangerous to mix old and new
batteries.
Contact your local waste disposal authority for instructions
on how to dispose of used batteries. Used batteries can be
harmful to the environment, and should not be thrown out
with household trash.
(MUTE)
SETTING DATE, TIME AND MEASUREMENT UNITS
3.
It is important to set the clock before using your blood
pressure monitor, so that a time stamp can be assigned to
each record that is stored in the memory.
NOTE When volume level 0 is s
and you will not hear any voice me
Normal Blood Pressure
120
130
140
150
160
180
Systolic blood pressure (mmHg)
1.
•
when you have fini
TAKING A BLOOD PRESSU
NOTE
Blood pressure is considered high when either the
diastolic or systolic blood pressure value exceeds the
normal range. When a patient’s systolic and diastolic
blood pressures fall into different categories, the
higher category should apply.
Only a physician can tell you your normal blood
pressure range and the point at which you are at risk.
Press
When the unit is off, press and hold SET for 2 seconds
to enter the setting mode.
Reference material: 1999 World Health OrganizationInternational Society of Hypertension Guidelines for the
management of hypertension, Journal of Hypertension,
1999, 17(2): 151-183.
•
1
(VOLUME
LOW)
High-normal Blood Pressure
Optimal Blood
Pressure
he maximum benefit from using
rve the following care guidelines.
ore the unit in a dry place away
•
ABOUT BLOOD PRESSURE
What is blood pressure?
Wrist cuff air is
exhausting or
deflating
tion
•
Shows which user
profile (1 or 2 is
being displayed)
Unit is inflating
with air to obtain
the needed level of
pressure
of
•
Diastolic blood pressure (mmHg)
y
•
Do not immerse the unit in water. If it comes in contact
with water, dry it immediately with a soft lint-free cloth.
Use a soft, slightly moistened cloth to wipe off the unit
and cuff. Do not use abrasive or corrosive cleaning
agents, as these may cause damage.
Remove the batteries whenever you are planning to
store the unit for a long period of time.
When replacing batteries, use new batteries as
specified in this user manual. Do not mix new and old
batteries.
Do not place objects such as stickers on the wrist cuff
or unit, as these may impair the measurement.
Do not subject the unit to excessive force, shock, dust,
temperature changes, or humidity. Such treatment
may result in malfunction, a shorter electronic life
span, damaged batteries, or distorted parts.
Do not tamper with the internal components. Doing
so will terminate the product warranty and may cause
damage.
The unit contains no user- serviceable parts.
If you no longer need to use this product, protect the
environment by bringing it to your dealer or designated
collection point for proper disposal.
2.
3.
The setting order is as follows: 12/24 hour format,
hour, minute, year, month/day or day / month format,
month, date, and measurement unit (kPa or mmHg).
Press
or
to increase / decrease a value or change the
setting.
You can choose to take your blood
down. Below are some helpful tips f
•
Be sure to set the clock
measurement, or whenever
so that the date and time a
with your history. For instruc
time and measurement units
•
It is important to relax when t
Try to take a 15-minute rest
•
Do not lean backward or be
taking a measurement.
•
Avoid talking or moving yo
taking a measurement. Ra
n to obtain these values. If the
with these products fall outside
ur physician.
ure fluctuate throughout the day?
varies greatly both on a daily and
basis. These variations may be
ertensive patients. Normally the
e at work and is at its lowest
s the variations over a single day
every 5 minutes. The thick line
e rises in blood pressure at 4PM
M (Bin the graph) correspond to
al intercourse (Beven, Honour &
69).
4.
5.
Press SET to accept the change and switch to the next
setting.
When you are finished, press to exit the setup menu.
•
•
POSITIONING THE WRIST CUFF
It is important to properly position the wrist cuff to ensure
that you receive an accurate reading.
1.
2.
3.
4.
5.
Remove all accessories (watch, bracelet, etc.) from
your left wrist. If your physician has diagnosed you with
poor circulation in your left arm, use your right wrist.
Roll or push up your sleeve to expose the skin.
Apply the cuff to your left wrist with your palm facing up.
Position the edge of the cuff about 0.4 inches (1cm)
from the bottom of your palm.
Fasten the wrist cuff around your wrist, leaving no
extra room between the cuff and your skin. If the cuff
is too loose, the measurement will not be accurate.
ESSURE MONITOR WORKS
•
•
•
•
•
activities may alter your reading.
Wait at least an hour before taking your blood pressure
if you have just eaten a large meal.
Do not smoke or drink alcohol before taking your blood
pressure.
Do not measure your blood pressure if you are under stress.
Wait at least 3 minutes between measurements. This
allows your blood circulation to recover.
For a meaningful comparison, try to measure under
similar conditions. For example, take daily measurements
at approximately the same time, on the same wrist, or as
directed by a physician.
To stop the measurement process at any time, press .
The unit automatically switches off 1 minute after
taking a measurement. To save the battery life, press
as soon as you are finished to turn off the unit.
To take a measurement:
1. Choose the position from which you wish to
measure - sitting or lying down.
2. Position your body so that your wrist is parallel with your
heart, using the chart and illustrations below as a guide.
IF YOU
ARE...
THEN...
Sitting
d o w n
with an
armrest
Place your elbow on a table, using an object
as a support under your forearm. Your wrist
should be parallel to your heart, with the
palm facing up.
cillometric Measuring method to
re. Before every measurement,
o pressure”equivalent to the air
wrist cuff to 180mmHg or higher
blocked your blood in the artery.
ocess starts, during which time
oscillations generated by beatused to determine the systolic,
ure, and also your pulse rate.
eriod will result in an incorrect
readings are determined and
e measurement is finished and
y deflates.
LACING THE BATTERIES
over.
matching the correct polarity, as
use the correct battery type (2
ze).
Sitting
down
with no
armrest
To view a history of User 2’s reco
NOTE
•
The most recent record (1)
measurement is assigned to th
records are pushed back one d
so on), and the last record (30) i
Press the corresponding user
to see additional records.
Press and hold the correspon
advance to additional records.
The date and time of measu
with each record.
Memory records will be kept
become exhausted and are re
•
•
•
•
DELETING A MEASUREMENT R
You have the option of deleting
record or entire measurement
measurements have not been
need to be recorded again.
DELETING A SINGLE RECOR
1.
3.
4.
5.
VOICE PLAYBACK OF BLOOD PRESSURE
MEASUREMENTS
The BPW810N features voice playback during and after blood
pressure measurement results, as well as general
instructions to help you prepare for taking measurements.
When the unit has finished taking your measurement,
your blood pressure readings, pulse and blood pressure
classification are announced.
Lying
down
Position your wrist on a support, cushion,
or your thigh so that it is parallel to your
heart with the palm facing up.
If you want to repeat the announcement, simply press
TALK / VOLUME.
Anytime you recall a measurement record from memory,
it will also be announced. Press TALK / VOLUME if you
need to repeat the playback of any record.
VOLUME CONTROL
To adjust the volume level:
1. Press and hold TALK / VOLUME until volume level
flashes on the LCD.
2. Press TALK / VOLUME to adjust volume level.
Press
or
to recall the
record for User 1 or User 2.
Press and hold SET until the
Place your arm across your chest with
the wrist parallel to your heart. Hold your
elbow with the other hand.
NOTE Graphics may not exactly match product.
3. Relax your hand and press
to turn on the unit. A voice
will prompt you to sit in the correct position. Press
again. Voice will remind you to relax and remain still.
Wrist cuff will begin inflating automatically to measure
blood pressure.
Press SET. First record will
screen.
Press respective user button
through records and select t
Press and hold SET to delete
NOTE If you decide to abort the
FOR
ACTION
User 1 record Press
twice
User 2 record Press
once
6.
“dEL OnE” will be displayed
and hold SET to confirm.
NOTE Once the pressure reaches a certain level, it will
slowly deflate until the measurement results are displayed
on the LCD.
“dEL dOnE” indicates successful
1
(MUTE)
Press
(VOLUME IS
LOW)
2
(VOLUME IS
HIGH)
when you have finished adjusting the volume.
AND MEASUREMENT UNITS
3.
clock before using your blood
a time stamp can be assigned to
in the memory.
NOTE When volume level 0 is selected, the unit is on mute
and you will not hear any voice messages announced.
ess and hold SET for 2 seconds
ode.
as follows: 12/24 hour format,
onth/day or day / month format,
surement unit (kPa or mmHg).
se / decrease a value or change the
To view a history of User 1’s reco
2.
eries whenever the weak battery
ay is dim, or the display does not
r is on. Replace all the batteries
dangerous to mix old and new
isposal authority for instructions
batteries. Used batteries can be
nt, and should not be thrown out
RECALLING MEASUREMENTS S
NOTE This unit can intelligently adjust the cuff pressure
and inflate to a higher-pressure level (>180 mmHg) when
needed.
Your systolic and diastolic pressure readings flash on the
LCD, followed by MAP and pulse per minute readings
every 2 seconds. At the same time, your measurement
results and the blood pressure classification will also be
announced.
4.
5.
TAKING A BLOOD PRESSURE MEASUREMENT
You can choose to take your blood pressure while sitting or lying
down. Below are some helpful tips for taking a measurement:
•
Be sure to set the clock before taking your first
measurement, or whenever you replace the batteries,
so that the date and time are stored in the memory
with your history. For instructions, refer to "Setting date,
time and measurement units" section.
•
It is important to relax when taking your blood pressure.
Try to take a 15-minute rest before you begin.
•
Do not lean backward or bend your wrist inward while
taking a measurement.
•
Avoid talking or moving your fingers and hand while
taking a measurement. Rapid movements or other
To repeat the announcement, simply press TALK /
VOLUME.
or
If you want to save the record to memory, press
and the results will be saved to User 1’s or User 2’s
memory accordingly.
DELETING ALL RECORDS
1.
2.
3.
Press
or
to recall the
record for User 1 or User 2.
Press and hold SET until the
Press
to select option to
(“dEL ALL”).
The measurement is stored as the first (MEM 1) entry in
the user record you selected; the last entry (MEM 30) is
dropped, and all the entries in between move up 1 digit
(e.g. 28 becomes 29, and so on).
NOTE If you decide to abort the
ur reading.
efore taking your blood pressure
a large meal.
alcohol before taking your blood
d pressure if you are under stress.
s between measurements. This
ulation to recover.
mparison, try to measure under
xample, take daily measurements
me time, on the same wrist, or as
ent process at any time, press .
y switches off 1 minute after
. To save the battery life, press
finished to turn off the unit.
from which you wish to
ng down.
hat your wrist is parallel with your
nd illustrations below as a guide.
bow on a table, using an object
under your forearm. Your wrist
rallel to your heart, with the
p.
RECALLING MEASUREMENTS STORED IN MEMORY
To view a history of User 1’s records, press
.
To view a history of User 2’s records, press
.
NOTE
•
The most recent record (1) is shown first. Each new
measurement is assigned to the first (1) record. All other
records are pushed back one digit (e.g., 2 becomes 3, and
so on), and the last record (30) is dropped from the list.
or
)
Press the corresponding user button again (
to see additional records.
Press and hold the corresponding user button to autoadvance to additional records.
The date and time of measurements taken are shown
with each record.
Memory records will be kept even when the batteries
become exhausted and are replaced.
•
•
•
•
ss
to turn on the unit. A voice
he correct position. Press
you to relax and remain still.
ing automatically to measure
You have the option of deleting your latest measurement
record or entire measurement history. This is useful if
measurements have not been accurately recorded and
need to be recorded again.
User 1 record Press
once User 1 records
displayed
User 2 record Press
twice User 2 records
displayed
4.
Press and hold SET for 2 seconds to delete all
measurement records. After you have confirmed
deleting all records, the screen shows “dEL dOnE”.
The no --- screen indicates successful deletion and there
are no records stored.
no
2.
TECHNICAL SPECIFICATION
Press
or
to recall the latest measurement
record for User 1 or User 2.
Press and hold SET until the LCD shows “dEL OnE”.
Application:
Measuring method
Application
Measurement location
Memory
MEM
TROUBLESHOOTING
This section includes a list of error messages and frequently
asked questions for problems you may encounter with your
blood pressure monitor. If the product is not operating as you
think it should, check here before arranging for servicing.
3.
4.
5.
Press SET. First record will be displayed on LCD
screen.
Press respective user button (
/
) to scroll
through records and select the record to be deleted.
Press and hold SET to delete record.
NOTE If you decide to abort the delete action instead:
FOR
ACTION
RETURN TO SCREEN
DISPLAY
User 1 record Press
twice User 1 records
displayed
User 2 record Press
once User 2 records
displayed
6.
“dEL OnE” will be displayed on LCD screen. Press
and hold SET to confirm.
Problem Symptom
No
power
Check This
Display is Batteries are
dim or will exhausted
not light up
Batteries are
inserted
incorrectly
shows Batteries
Low
batteries on the
are low
display
Remedy
Replace with
new batteries
Insert the
batteries
correctly
Replace
with new
batteries
-
Maximum number of users
Dimensions:
Height x Width x Depth
Weight
Cuff circumference
Measuring range:
Pressure
Osci
For a
Wris
Max
per u
2
3.5 x
(90 x
6.3 o
5.3 t
to 19
Pulse
30 to
(4.0
40 t
Accuracy:
Pressure
Pulse
+/- 3
+/- 5
Power:
Power supply
Power save
3V D
UM4
Auto
minu
Operating environment:
Operation
50°F
Storage / Transport
-4°F
Humidity range
10%
BLOOD PRESSURE LOG BO
“dEL dOnE” indicates successful deletion.
lligently adjust the cuff pressure
ssure level (>180 mmHg) when
DELETING ALL RECORDS
1.
ncement, simply press TALK /
or
record to memory, press
be saved to User 1’s or User 2’s
RETURN TO SCREEN
DISPLAY
DELETING A SINGLE RECORD
1.
eaches a certain level, it will
surement results are displayed
pressure readings flash on the
nd pulse per minute readings
same time, your measurement
ssure classification will also be
ACTION
DELETING A MEASUREMENT RECORD FROM MEMORY
arm across your chest with
allel to your heart. Hold your
e other hand.
r wrist on a support, cushion,
so that it is parallel to your
e palm facing up.
FOR
2.
3.
Press
or
to recall the latest measurement
record for User 1 or User 2.
Press and hold SET until the LCD shows “dEL OnE”.
Press
to select option to delete all records
(“dEL ALL”).
d as the first (MEM 1) entry in
ed; the last entry (MEM 30) is
es in between move up 1 digit
so on).
NOTE If you decide to abort the delete action instead:
To create a log of your blood press
personal information section at the
(date, time, and measurements) fo
To plot your history, use an S (s
M (mean arterial pressure) to ma
measurement falls on the chart, th
view your history over time.
ON
Name:
RETURN TO SCREEN
DISPLAY
Age:
Weight:
(kg/lbs)
(kg/lbs
once User 1 records
displayed
twice User 2 records
displayed
T for 2 seconds to delete all
rds. After you have confirmed
, the screen shows “dEL dOnE”.
ates successful deletion and there
no
TECHNICAL SPECIFICATIONS
Application:
Measuring method
Application
Measurement location
Memory
of error messages and frequently
ms you may encounter with your
he product is not operating as you
before arranging for servicing.
Check This
Remedy
atteries are
xhausted
Replace with
new batteries
atteries are
serted
correctly
Insert the
batteries
correctly
atteries
re low
Replace
with new
batteries
-
Maximum number of users
Dimensions:
Height x Width x Depth
Weight
Cuff circumference
Measuring range:
Pressure
Oscillometric / noninvasive
For adult use only
Wrist section of lower arm
Maximum 30 records
per user
2
3.5 x 3.4 x 1.2 inches
(90 x 86 x 30.8 mm)
6.3 oz (180g) without batteries
5.3 to 7.7 inches (13.5
to 19.5 cm)
Pulse
30 to 280 mmHg
(4.0 to 37.3 kPa)
40 to 200 pulse/min
Accuracy:
Pressure
Pulse
+/- 3 mmHg (+/- 0.4 kPa)
+/- 5%
Power:
Power supply
Power save
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientifi
www.oregonscientific.com
c.com) to learn more
about Oregon Scientific products.
If you’re in the US and would like to contact our Customer
Care department directly, please visit:
www2.oregonscientific.com/service/support.asp
For international inquiries, please visit:
www2.oregonscientific.com/about/international.asp.
c.com/about/international.asp
EU-DECLARATION OF CONFORMITY
Hereby, Oregon Scientific, declares that this Talking Blood
Pressure Monitor(Model: BPW810N) is in compliance with
EMC directive 2004/108/EC. A copy of the signed and
dated Declaration of Conformity is available on request
via our Oregon Scientific Customer Service.
3V DC, 2 LR03 / AAA /
UM4-size 1.5V batteries
Auto power off after 1
minute of non-activity
Operating environment:
Operation
50°F to 104°F (10°C to 40°C)
Storage / Transport
-4°F to 140°F (-20°C to 60°C)
Humidity range
10% to 83% relative humidity
BLOOD PRESSURE LOG BOOK
To create a log of your blood pressure history, complete the
personal information section at the top, then enter the details
(date, time, and measurements) for each reading you take.
To plot your history, use an S (systolic), D (diastolic) and
M (mean arterial pressure) to mark the points where each
measurement falls on the chart, then connect the points to
view your history over time.
Protected by US. Patent no. 7,211,047
© 2009 Oregon Scientific. All rights reserved.
P/N.:300100682-00012-10
Download PDF