Panasonic PT-AE700U User's manual

Panasonic PT-AE700U User's manual
LCD Projector
Operating Instructions
Model No.
PT-AE700U
Before operating this product, please read the instructions carefully and save this
manual for future use.
For assistance, please call : 1-888-View-PTV(843-9788)
or send e-mail to : [email protected]
or visit us at www.panasonic.com
(U.S.A)
For assistance, please call : 787-750-4300
or visit us at www.panasonic.co.jp/global/
(Puerto Rico)
TQBJ 0161-1
ENGLISH
R
This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most out of your new
product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should
note it in the space provided below and retain this booklet in case service is
required.
Model number: PT-AE700U
Serial number:
IMPORTANT SAFETY NOTICE
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only.
CAUTION: The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.
CAUTION: This equipment is equipped with a threepin grounding-type power plug. Do not
remove the grounding pin on the power
plug. This plug will only fit a groundingtype power outlet. This is a safety feature.
If you are unable to insert the plug into
the outlet, contact an electrician. Do not
defeat the purpose of the grounding plug.
Do not remove
WARNING:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when
connecting to computers or peripheral devices.
Any unauthorized changes or modifications to this equipment will void the
users authority to operate.
WARNING:
Not for use in a computer room as defined in the Standard for the Protection
of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
2-ENGLISH
Declaration of Conformity
Model Number:
PT-AE700U
Trade Name:
Panasonic
Responsible party: Matsushita Electric Corporation of America.
Address:
One Panasonic Way Secaucus New Jersey 07094
Telephone number: 1-888-View-PTV(843-9788)
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
ENGLISH-3
Preparation
Dear Panasonic Customer:
Preparation
IMPORTANT SAFETY NOTICE ...2
Precautions with regard to
safety .........................................5
Accessories .................................9
Before use ....................................9
Location and function of each
part...........................................11
Getting started
Setting-up...................................16
Projection methods, Projector
position, Projection distances,
Setting up range using the lens shift
function
Connections...............................20
Connecting to video equipment,
Connecting to equipment
compatible with HDMI,
Connecting to computer
Preparation for the remote
control unit..............................23
Basic operation
Turning on the power................24
Turning off the power................26
Useful functions
Correcting keystone distortion ...28
Pausing a picture.......................28
Selecting the picture mode.......29
Turning on the button lights.....29
Setting the aspect ratio.............30
Using the COLOR MANAGEMENT...32
Retrieving the saved picture
settings....................................35
Adjustments and settings
On-screen menus ......................36
Menu screens, Menu operation
guide, Returning a setting to the
factory default
Adjusting the picture.................40
PICTURE MODE, CONTRAST,
BRIGHT, COLOR, TINT,
SHARPNESS, COLOR TEMP.,
4-ENGLISH
Precautions with regard to safety
DYNAMIC IRIS, ADVANCE MENU,
MEMORY SAVE, MEMORY LOAD,
TV-SYSTEM, SIGNAL MODE,
Projecting sRGB-compatible pictures
Adjusting the position...............44
Horizontal position, Vertical position,
DOT CLOCK, CLOCK PHASE,
ASPECT,AUTO SETUP
Turning off the picture
momentarily (SHUTTER)........45
Changing the display language...45
Option settings ..........................46
OSD, Noise Reduction (NR),
CINEMA REALITY, BACK COLOR,
WSS, FRONT/REAR,
DESK/CEILING, FAN CONTROL,
LAMP POWER, LAMP RUNTIME
Care and maintenance
When the TEMP indicator and the
LAMP indicator are illuminated...48
Cleaning and replacing
the air filter ..............................50
Replacing the lamp unit ............51
Before calling for service..........54
Cleaning and maintenance .......55
Others
Specifications ............................56
Appendix ....................................58
List of compatible signals, General
arrangement of the COLOR
MANAGEMENT menu, Projection
dimensions calculation methods
Dimensions ................................61
Trademark acknowledgements...62
WARNING
If you notice smoke, strange smells or noise coming from the projector,
disconnect the power cord plug from the wall outlet.
B Do not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
B Check that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
B Do not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
B If the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
B If installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, disconnect the power cord plug from
the wall outlet.
B Continued use of the projector in this condition may result in fire or electric
shocks.
B Contact an Authorized Service Center for repairs.
Do not overload the wall outlet.
B If the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
B High voltages can cause fire or electric shocks.
B For any inspection, adjustment and repair work, please contact an
Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming
covered in dust.
B If dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord plug
out from the wall outlet and wipe it with a dry cloth.
B If not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet.
ENGLISH-5
Preparation
Contents
6-ENGLISH
Do not use the projector in a bath or shower.
B Fire or electric shocks can result.
Do not look into the lens while the projector is being used.
B Strong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
B Be especially careful not to let young children look into the lens. In
addition, turn off the power and disconnect the power cord plug when you
are away from the projector.
Do not place your hands or other objects close to the air outlet port.
B Heated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
Replacement of the lamp unit should only be carried out by a qualified
technician.
B The lamp unit has high internal pressure. If improperly handled, explosion
might result.
B The lamp unit can easily become damaged if struck against hard objects
or dropped, and injury or malfunctions may result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
B The lamp cover gets very hot, and touching it can cause burns.
Before replacing the lamp, be sure to disconnect the power cord plug
from the wall outlet.
B Electric shocks or explosions can result if this is not done.
Caution
Do not cover the air inlet port or the air outlet port.
B Doing so may cause the projector to overheat, which can cause fire or
damage to the projector.
B Do not place the projector in narrow, badly ventilated places such as
closets or bookshelves.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
B Using the projector under such conditions may result in fire or electric shocks.
When disconnecting the power cord, hold the plug, not the cord.
B If the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
B Moving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.
Do not place any heavy objects on top of the projector.
B Failure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
ENGLISH-7
Preparation
Do not do anything that might damage the power cord or the power
cord plug.
B Do not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
B If the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
B Ask an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not handle the power cord plug with wet hands.
B Failure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
B If the plug is not inserted correctly, electric shocks or overheating could
result.
B Do not use plugs which are damaged or wall outlets which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
B If the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
B Failure to observe this may result in fire or electric shocks.
Do not place liquid containers on top of the projector.
B If water spills onto the projector or gets inside it, fire or electric shocks
could result.
B If any water gets inside the projector, contact an Authorized Service
Center.
Do not insert any foreign objects into the projector.
B Do not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
Keep the batteries out of the reach of infants.
B If the batteries are swallowed, death by suffocation may result. If you
believe that the batteries may have been swallowed, seek medical advice
immediately.
Do not allow the + and - terminals of the batteries to come into contact
with metallic objects such as necklaces or hairpins.
B Failure to observe this may cause the batteries to leak, overheat, explode
or catch fire.
B Store the batteries in a plastic bag and keep them away from metallic
objects.
During a thunderstorm, do not touch the projector or the cable.
B Electric shocks can result.
NOTICE:
B This product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
8-ENGLISH
Accessories
Check that all of the accessories shown below have been included with your
projector.
Remote control unit
(N2QAEA000025 x1)
Video cable
[3.0 m (9´10˝),
K2KA2FA00003 x1]
AAA batteries for
remote control unit (x2)
Power cord
(K2CG3FR00001 x 1)
Before use
Cautions regarding setting-up
Avoid setting up in places which are subject to vibration or shocks.
The internal parts can be damaged, which may cause malfunctions or
accidents.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
You will need to purchase the separate installation kit (Model No.ET-PKE700).
Furthermore, all installation work should only be carried out by a qualified
technician.
If using this projector at high elevations (above 1 400 m), set the “FAN
CONTROL” to “HIGH”. (Refer to page 47.)
Failure to observe this may result in malfunctions.
ENGLISH-9
Preparation
Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.
B Failure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.
When inserting the batteries, make sure the polarities (+ and -) are
correct.
B If the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Use only the specified batteries.
B If incorrect batteries are used, they may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Do not mix old and new batteries.
B If the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Do not put your weight on this projector.
B You could fall or the projector could break, and injury may result.
B Be especially careful not to let young children stand or sit on the projector.
Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.
B Electric shocks can result if this is not done.
Ask an Authorized Service Center to clean inside the projector at least
once a year.
B If dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation.
B It is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to
clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean
environment. Please take non repairable units back to your dealer or a
recycling company.
Notes on use
In order to get the best picture quality
Draw curtains or blinds over any windows and turn off any lights near the
screen to prevent outside light or light from indoor lamps from shining onto
the screen.
Preparation
Location and function of each part
Projector <Top, right and front>
#
$ % ˛&
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the lens cover.
˛-
'
Screen
Do not apply any volatile substances which may cause discoloration to the
screen, and do not let it become dirty or damaged.
˛*
˛
,
˛(
Lamp
The lamp may need to be replaced earlier due to variables such as individual
lamp characteristics, usage conditions and the installation environment,
especially when the projector is subjected to continuous use for more than
10 hours or the power is frequently turned on and off.
Liquid crystal panel
B Do not project the same image for long periods of time, as this may remain
as an afterimage on the liquid crystal panel.
B The liquid crystal panel of the projector is built with very high precision
technology to provide fine picture details. Occasionally, a few non-active
pixels may appear on the screen as fixed points of blue, green or red.
Please note that this does not affect the performance of your LCD.
˛+
˛*
˛)
# Projector control panel (page 14)
$ Zoom ring (page 25)
% Focus ring (page 25)
& Projection lens
' Air inlet port
Do not cover this port.
( Air filter (page 50)
) Shift lever (page 25)
This lever adjusts the lens direction.
* Front adjustable legs (L/R) (page 25)
+ Lens cover
, Remote control signal receptor (page 23)
- Air outlet port
Do not cover this port.
WARNING
Do not place your hands or other objects close to the air outlet port.
B Heated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
10-ENGLISH
ENGLISH-11
#
Preparation
Projector <Back and bottom>
Connector panel
$
˛%
#
$
%
&
(
&
'
'
(
# Connector panel (page 13)
$ Air inlet port
Do not cover this port.
% Power input socket (AC IN) (page 24)
The accessory power cord is connected here.
Do not use any power cord other than the accessory power cord.
& Security lock
This can be used to connect a commercially-available theft-prevention
cable (manufactured by Kensington). This security lock is compatible with
the Microsaver Security System from Kensington.
' Lamp unit cover (page 51)
( MAIN POWER switch (pages 24 and 26)
12-ENGLISH
# TRIGGER connector (pages 20, 21 and 22)
This connector outputs 12 V when the power is turned on. Connect this
connector to equipment such as an electric screen.
$ HDMI IN connector (page 21)
This connector is used to input HDMI signals.
% PC IN (RGB input) connector (page 22)
This connector is used to input RGB signals from a PC.
& S-VIDEO IN connector (page 20)
This connector is used to input signals from an S-VIDEO-compatible
equipment such as a video deck.
' VIDEO IN connector (page 20)
This connector is used to input video signals from a video equipment such
as a video deck.
( COMPONENT IN [YPBPR(CBCR) input] connectors (page 20)
These connectors are used to input YPBPR signals from compatible
equipment such as a DVD player.
ENGLISH-13
# $%
*
&
) (
'
Remote control unit
*
+
)
(
&
,
'
2
-
1
0
14-ENGLISH
.
/
# Power indicator (pages 24, 26 and 27)
This indicator illuminates red when the main power is switched on (standby
mode), and it illuminates green when a picture starts to be projected.
$ LAMP indicator (page 49)
This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.
% TEMP indicator (page 48)
This indicator illuminates if an abnormally high temperature is detected
inside the projector. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash.
F, G, I and H) buttons (page 38)
& Arrow (F
These buttons are used to select and adjust items in the on-screen menus.
' ENTER button (page 38)
This button is used to accept and to activate items selected in the
on-screen menus.
( MENU button (page 36)
This button is used to display the “MAIN MENU”. When a menu screen is being
displayed, it can be used to return to a previous screen or to clear the screen.
) INPUT select buttons (page 25)
These buttons are used to switch the input signals from the connected equipment.
* POWER button (pages 24 and 26)
+ LIGHT button (page 29)
This button is used to illuminate the buttons on the remote control unit.
, KEYSTONE button (page 28)
This button is used to correct keystone distortion of the projected image
when the projector position is tilted upward or downward.
- FREEZE button (page 28)
This button is used to momentarily freeze projection so that a still picture is
displayed.
. PICTURE MODE button (page 29)
Pressing this button will change the picture mode.
/ USER MEMORY button (page 35)
This button is used to display the “MEMORY LOAD” menu.
0 COLOR MANAGEMENT button (page 32)
This button is used to display the “COLOR MNGMT” menu.
1 ASPECT button (page 30)
This button is used for aspect adjustment (vertical and horizontal
proportions).
2 NORMAL button (page 39)
This button is used to reset the projector adjustment values to the factory
default settings.
ENGLISH-15
Preparation
Projector control panel
Setting-up
BFront-ceiling projection
Screen
L: Projection distance
SH: Image height
SW:Image width
L
Menu items
Setting
Menu items
Setting
FRONT/REAR
FRONT
FRONT/REAR
FRONT
DESK/CEILING
DESK
DESK/CEILING
CEILING
BRear-desk projection
(Using a translucent screen)
BRear-ceiling projection
(Using a translucent screen)
SW
82.9 mm
(3-1/4˝)
BFront-desk projection
SH
In way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the “OPTION” menu. Refer
to page 47 for details.)
L
Screen
Projection distances
Screen size (16:9)
Menu items
Setting
Menu items
Setting
FRONT/REAR
REAR
FRONT/REAR
REAR
DESK/CEILING
DESK
DESK/CEILING
CEILING
NOTE:
B You will need to purchase the separate ceiling bracket (ET-PKE700)
when using the ceiling installation method.
B If you set up the projector vertically, it may cause
damage to the projector.
B It is recommended that you set up the projector
in a place that is tilted at less than ±30°. Setting
Diagonal
length
Height
(SH)
1.01 m(40˝)
1.27 m(50˝)
1.52 m(60˝)
1.77 m(70˝)
2.03 m(80˝)
2.28 m(90˝)
2.54 m(100˝)
3.05 m(120˝)
3.81 m(150˝)
5.08 m(200˝)
0.50 m(1´7˝)
0.62 m(2´)
0.75 m(2´5˝)
0.87 m(2´10˝)
1.00 m(3´3˝)
1.12 m(3´8˝)
1.24 m(4´)
1.49 m(4´10˝)
1.87 m(6´1˝)
2.49 m(8´2˝)
Projection distance (L)
Width
(SW)
0.89 m(2´11˝)
1.11 m(3´7˝)
1.33 m(4´4˝)
1.55 m(5´1˝)
1.77 m(5´9˝)
1.99 m(6´6˝)
2.21 m(7´3˝)
2.66 m(8´8˝)
3.32 m(10´10˝)
4.43 m(14´6˝)
Wide
(LW)
Telephoto
(LT)
1.2 m(3´11˝)
1.5 m(4´11˝)
1.8 m(5´10˝)
2.1 m(6´10˝)
2.4 m(7´10˝)
2.7 m(8´10˝)
3.1 m(10´2˝)
3.7 m(12´1˝)
4.6 m(15´1˝)
6.2 m(20´4˝)
2.4 m(7´10˝)
3.0 m(9´10˝)
3.7 m(12´1˝)
4.3 m(14´1˝)
4.9 m(16´)
5.5 m(18´)
6.2 m(20´4˝)
7.4 m(24´3˝)
9.3 m(30´6˝)
12.4 m(40´8˝)
NOTE:
B The dimensions in the table above are approximate.
B For details about projected image distances, refer to page 60.
up the projector in places that are tilted at more
than ±30° may cause malfunctions.
16-ENGLISH
ENGLISH-17
Getting started
Projector position
Projection methods
Setting up range using the lens shift function
BSetting up range
H
Projector
BHorizontal lens shift
About 25% of the
screen (maximum)
About 25% of the
screen (maximum)
Getting started
This projector can be placed in various places by controlling the shift lever at
the front side of the projector to move the lens in order to adjust the position
of the projected image.
V
Screen
Projector set up range
(center of the lens)
Screen
When shift lever is moved
to the left (full)
When shift lever is moved
to the right (full)
BVertical lens shift
When shift lever is
moved down (full)
About 63% of
the screen
(maximum)
Screen
About 63% of
the screen
(maximum)
When shift lever is
moved up (full)
18-ENGLISH
Vertical (V) Horizontal (H) * The values in the table are for the width and
the height of the screen.
About 63%
About 0%
About 50%
About 8%
About 30%
About 17%
About 10%
About 23%
About 0%
About 25%
NOTE:
B Turn the shift lever right to secure the shift lever.
B When the lens has been shifted fully to the right or left, you will not be
able to shift the lens up or down.
When the lens has been shifted fully up or down, you will not be able to
shift the lens to the right or left.
B Generally, the maximum picture quality is obtained when the lens is
moved to the center (horizontally and vertically).
ENGLISH-19
Connections
Connecting to equipment compatible with HDMI
B Read the instruction manual for each peripheral device carefully before
connecting it.
B Turn off the power supply for all peripheral devices before making any
connections.
B If the cables necessary for connection are not included with the peripheral
device or available as an option, you may need to prepare a proper cable
for the device concerned.
B Refer to the list on page 58 for details on compatible signals which can be
input to the projector.
B An audio system circuit is not provided with this projector. Connect the
audio output of the connected equipment to a separate audio system.
DVD player
Getting started
Notes on connections
To HDMI output
HDMI cable (sold
separately)
Connecting to video equipment
Equipment such as
an electric screen
To S-Video output
DVD player
Equipment such as
an electric screen
To Video output
Video deck
NOTE:
B Use the HDMI cable with the HDMI logo.
B When connecting to equipment compatible with DVI, use the DVI - HDMI
adapter cable (sold separately).
B This projector can be connected to HDMI and DVI equipment, but some
equipment may not operate correctly, for example images may not appear.
Video cable
(accessory)
To YPBPR output
DVD player
20-ENGLISH
ENGLISH-21
Preparation for the remote control unit
Connecting to computer
# Open the cover.
To RGB
output
Getting started
Computer
$ Insert the batteries so that the
polarities are correct, and then close the
cover.
AAA batteries
(two)
NOTE:
B Do not drop the remote control unit.
B Keep the remote control unit away from liquids.
B Remove the batteries if not using the remote control unit for long periods.
B Do not use rechargeable batteries.
Equipment such as
an electric screen
Operating range
If the remote control unit is held so that it is facing directly in front of the
remote control signal receptor, the operating range is within approximately
7 m (23´) from the surfaces of the receptor. Furthermore, the remote control
unit can be operated from an angle of ±30° to the left or right and ±15°
above or below the receptor.
NOTE:
B If there are any obstacles in between the remote control unit and the
receptor, the remote control unit may not operate correctly.
B If strong light is allowed to shine onto the remote control signal receptor,
correct projector operation may not be possible. Place the projector as
far away from light sources as possible.
B If facing the remote control unit toward the screen to operate the projector,
the operating range of the remote control unit will be limited by the amount
of light reflection loss caused by the characteristics of the screen used.
22-ENGLISH
ENGLISH-23
Turning on the power
select button to select the input signal.
& Press the input
Input select
Before turning on the power
1. Ensure that all peripheral
devices are connected properly.
2. Connect the accessory power cord.
3. Remove the lens cover.
button
˛$
Changing
signals
VIDEO
S-VIDEO
HDMI
˛#
Input select
button
Remote
control
unit
˛&
Changing
signals
VI D E O
YPBPR
PC
CMPNT
PC
VIDEO
YPBPR
HDMI
S-VIDEO
BA picture will be projected in accordance with the selected input signal.
˛(
˛'
˛*
˛) ˛(
Power indicator
Lens cover
the MAIN POWER switch to turn on the
# Press
power.
BThe power indicator on the projector will illuminate red.
the POWER button.
$ Press
BThe power indicator on the projector will flash green. After a short
period, the indicator will illuminate green, and a picture will be
projected.
on the power of all connected devices.
% Turn
BStart the play function of a device such as a DVD player.
NOTE:
B A rattling sound may be heard when the power is turned on, and a
tinkling sound may be heard when the lamp unit is turned on, but these
are not signs of malfunctions.
Follow the procedure below when you set the projector up first, and when
you change the setup place.
the lens shift
' Adjusting
BUse the shift lever to adjust the
position of the projected image.
BTurn the shift lever right to secure
the shift lever.
˛'
the angle
( Adjusting
BThe position of the projected image
(upward and downward) can be fine
adjusted by turning the front
adjustable legs.
BIf the projected image contains
keystone distortion, adjust
“KEYSTONE” (refer to page 28 for
details).
the size
) Adjusting
BTurn the zoom ring to adjust
the size of the projected image.
˛(
˛(
˛)Zoom
˛ Focus
*
the focus
* Adjusting
BTurn the focus ring to adjust
the focus of the projected image.
24-ENGLISH
ENGLISH-25
Basic operation
Power cord
Control
panel
Turning off the power
˛#
˛$
Power indicator
the POWER button.
# Press
B“POWER OFF” is displayed on the
screen.
POWER OFF
OK
CANCEL
the I or H button to select “OK”, and
$ Press
then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected.
(The power indicator on the projector will illuminate orange while the
cooling fan is still operating.)
the MAIN POWER switch to turn off the
% Press
power after the power indicator on the
NOTE:
B During projection of an image, the cooling fan will operate, emitting a
small noise as it operates. Turning the lamp on or off will cause this
noise to increase a little.
B By using the “OPTION” menu to set “LAMP POWER” to “LOW”, the
operating sound of the fan can be reduced. (Refer to page 47.)
B You can also turn off the power by pressing the POWER button twice or
by holding it down for at least 0.5 seconds.
B When the projector is in standby mode (the power indicator on the
projector is illuminated red), the projector continues to draw approximately
3.0 W of power even when the cooling fan has stopped.
Power indicator
Power indicator status
Red
Green
projector illuminates red.
Illuminated
Flashing
Illuminated
BDo not cut power to the projector in any way while the cooling fan is
still operating. Be careful not to switch off the MAIN POWER switch
of the projector or unplug the power cord from the wall outlet.
Illuminated
Orange
Flashing
26-ENGLISH
Projector status
The projector is in standby mode and image projection
is possible by pressing the POWER button.
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated red. (After a short period, a picture will be
projected.)
A picture is being projected.
The lamp is cooling down after the power is turned
off. (The cooling fan is operating.)
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated orange. (After a short period, a picture
will be projected.)
ENGLISH-27
Basic operation
˛%
Correcting keystone distortion (KEYSTONE)
Selecting the picture mode (PICTURE MODE)
When either the projector or the screen is tilted, the keystone distortion will
affect the image. You can correct the image proportions by the following
procedure. (Vertical keystone distortion correction only.)
You can select the appropriate picture mode for the type of projected image.
Press the KEYSTONE button.
KEYSTONE
0
NORMAL ............When watching various image sources.
Vertical
keystone
distortion
correction
DYNAMIC ...........When the projector is used in a bright room.
Press the H button.
Press the I button.
NOTE:
B Vertical keystone distortion can be corrected to ±30° of the angle of tilt.
However, the greater the correction amount, the more the picture quality will
deteriorate, and the harder it will become to achieve a good level of focus. To
obtain the best picture quality, set up the projector and screen in such a way
that the amount of keystone correction required is as minimal as possible.
B The picture size will also change when correction of keystone distortion
is carried out.
B You can also correct keystone distortion from the “KEYSTONE” in the
“MAIN MENU”.
B Keystone distortion of the on-screen display will not be corrected.
B Keystone distortion may remain depending on the lens shift adjustment.
Pausing a picture (FREEZE)
Press the FREEZE button.
CINEMA1 ............When watching movies. The projected image will be refined.
This mode was well tuned to the look of Hollywood movie.
CINEMA2 ............When watching movies. The projected image will be clear
and have high contrast.
CINEMA3 ............When watching movies. The projected image will have
deep, rich colors.
VIDEO .................When watching video sources such as music or sports
programs.
NATURAL...........To reproduce the color of the image faithfully from the
image source.
NOTE:
B The picture mode can be also selected in the “PICTURE” menu.
B When the “PICTURE MODE” menu is selected, the settings will switch
automatically to the last “PROFILE” settings (page 32) that were used for
the selected picture mode.
Turning on the button lights (LIGHT)
Still picture
B The picture being projected will be paused.
B Press the FREEZE button again to cancel the
still picture.
28-ENGLISH
Press the LIGHT button.
B The buttons on the remote control unit will be
illuminated.
B Press the LIGHT button again to turn off the
button lights. The button lights will be turned off
automatically when no buttons on the remote
control unit are pressed for 10 seconds.
ENGLISH-29
Useful functions
Operation
Press the PICTURE MODE button.
B Pressing the PICTURE MODE button will
change the picture mode.
Setting the aspect ratio (ASPECT)
ASPECT
This projector allows you to change the aspect ratio to match the type of
input signal.
4:3
4:3 input signal
4:3
Press the ASPECT button.
BPressing the ASPECT button will change the
aspect ratio according to the successive settings
shown below.
BIllustrations for aspect ratio settings are shown
on the next page. Refer to this illustration for
assistance in selecting a suitable aspect ratio.
16:9
Squeezed signal (image
contracted horizontally)
Horizontal expansion of
projected image
JUST\4:3\16:9\14:9\ZOOM1\ZOOM2
[When NTSC, 525i (480i) or 525p (480p) signal is being input]
AUTO\4:3\16:9\JUST\ZOOM
4:3\16:9\V SCROLL
4:3\16:9
[When 525p (480p) or 625p (576p) signal is being input]
4:3\16:9\JUST\ZOOM
14:9
14:9 letterbox signal
Expansion preserves
original ratio
B “AUTO” will be displayed according to the type of the signals being input.
When set to “AUTO”, the projector switches the aspect ratio automatically if
the input signal has a detector signal.
B The aspect ratios for the following signals are fixed, and cannot be
changed. (Refer to page 58.) 1 125 (1 080) /60i, 1 125 (1 080) /50i, 750
(720) /60p, 750 (720) /50p, WIDE 480/600/720/768/768-2
*WIDE768 signals can be set to “V SCROLL”.
JUST
4:3 input signal
Horizontal expansion of projected image
(Center of image is less distorted.)
ZOOM
ZOOM1
ZOOM2*
Letterbox signal
Expansion preserves
original ratio
PC
HDMI
NOTE:
B If a selected mode does not match the aspect ratio of the input signal, it
may affect the quality of viewing of the original picture.
B If using this projector in places such as cafes or hotels to display programs
for a commercial purpose or for public presentation, note that if the aspect
ratio selection function is used to change the aspect ratio of the screen
picture, you may be infringing the rights of the original copyright owner for
that program under copyright protection laws.
B If a 4:3 picture is projected onto a 16:9 screen, distortion may occur around the
edges of the picture so that part of the picture is no longer visible. Programs
which have 4:3 aspect ratios should be viewed in 4:3 mode to give proper
consideration to the aims and intentions of the original program’s creator.
B Image sizes such as Cinema-Vision that project wider than the 16:9
ratio will have narrow black fields at the top and bottom.
B When “WSS” is set to “ON”(page46), the projector switches the aspect ratio
automatically if the input signal has a detector signal.
B “WIDE” is displayed on the screen when “ASPECT” is set automatically (when
“WSS” is set to “ON”). Press the ASPECT button to switch the aspect ratio.
B You can also change the aspect ratio from the “POSITION” menu.
B When set to “V SCROLL”, vertical position can be adjusted by pressing the G and
F buttons (close the “POSITION” menu screen before adjusting vertical position).
30-ENGLISH
V SCROLL
4:3 input signal
(XGA/MXGA/SXGA/
WIDE768 only)
Projected image
A picture is projected without
expansion or reduction.
*“ZOOM2” is for 2.35 : 1 letterbox signals.
ENGLISH-31
Useful functions
S-VIDEO/VIDEO/
YPBPR
Input signal
Using COLOR MANAGEMENT
You can adjust, save, and retrieve the settings for the selected colors of the
projected image based on the selected picture mode to suit your preference.
B Press the F or G button to select an item, press
the I or H button to change the settings, and
press the ENTER button for confirmation.
B When the “PICTURE MODE” menu is selected, the settings will switch
automatically to the last “PROFILE” settings that were used for the
selected picture mode.
B When retrieving a profile, “EDIT” will not be displayed if the picture
mode being selected does not match the picture mode which had been
selected when that profile was saved.
B “LOG” and “PROFILE SAVE” are displayed only when the colors have
been adjusted in “CURSOR” menu.
Press the COLOR MANAGEMENT button.
PROFILE
B Retrieves the saved profile (color settings which have been adjusted).
PROFILE
NORMAL
[
USER1
[
USER2
[
USER3
NORMAL
When projecting images according to the setting of “PICTURE
MODE” (page 29). This setting is the factory default setting.
USER1/2/3 These items are displayed only when “PROFILE SAVE” has
been carried out. Refer to page 35 for details.
CURSOR
Press the ENTER button to display the cursor (B).
# Select the color you want to adjust with the cursor.
B Press the F, G, I and H buttons to move the cursor, and then press
the ENTER button.
B The selected color (C) and the adjustment menu (A) will be displayed.
$ Adjust the items in the adjustment menu.
B The color adjusted in the adjustment menu (D) will be displayed.
COLOR
Adjusts the deepness of the color.
TINT
Adjusts the hue of the color.
BRIGHT
Adjusts the brightness of the color.
% Press the ENTER button to apply the adjusted color.
B The letters PROCESSING and the progress status bar will be displayed
while the adjusted color is applied.
B The adjusted color settings will be saved in the “LOG” menu.
If you would like to continue to adjust another color after adjusting a color,
press the MENU button,and then repeat the steps from step #.
EDIT
CURSOR
B You can edit the settings for the selected color.
EDIT
CURSOR
LOG
PROFILE SAVE
SELECT
ENTER
A
COLOR
TINT
BRIGHT
SELECT
0
0
+2
ESC
ADJ
ESC
B
CURSOR
LOG
PROFILE SAVE
Lets you select a color, and adjust the color settings (page 33).
Lets you adjust the color settings again, or delete the
settings (page 34).
Lets you save the adjusted color settings (page 35).
NOTE:
B Refer to page 59 for the general arrangement of the “COLOR MNGMT”
menu.
B You can enter the “COLOR MNGMT” menu from the “ADVANCE
MENU” in the “PICTURE” menu (page 41).
32-ENGLISH
˛C
˛D
Screen
& Press the MENU button twice, and then save the adjusted color settings.
B Select the “PROFILE SAVE” menu from the “EDIT” menu. The adjusted
color settings will not be saved until you carry out “PROFILE SAVE”.
ENGLISH-33
Useful functions
COLOR MNGMT
PROFILE
NORMAL
EDIT
SELECT
ADJ
ESC
LOG
LOG
PICTURE MODE:CINEMA1
COLOR
TINT
PT.1
0
0
PT.2
-1
0
PT.3
0
+10
PT.4
-10
+10
PT.5
-6
+5
PT.6
+3
-3
PT.7
0
+7
PT.8
-1
+14
SELECT
ENTER
Selected
color
Press the ENTER button to display the
“LOG” menu.
BRIGHT
+4
-2
0
-9
+7
+1
+9
-4
ESC
Adjusted
color
LOG
CHANGE
DELETE
SELECT
ENTER
DELETE
OK
CANCEL
34-ENGLISH
ESC
Press the F or G button to select the
setting you want to adjust, and then
press the ENTER button to display the
selection screen.
CHANGE
The adjustment menu (page 33 A) will
be displayed. You can adjust the color
settings again.
DELETE
The selected color setting will be deleted.
When all of the settings in the “LOG”
menu are deleted, the “PROFILE” setting
will return to “NORMAL”.
The confirmation screen will be
displayed when the ENTER button is
pressed. Select “OK” to delete the
settings.
PROFILE SAVE
PROFILE SAVE
USER 1
USER 2
USER 3
SELECT
ENTER
ESC
PROFILE SAVE
OK
CANCEL
Press the ENTER button to display the
“PROFILE SAVE” menu.
Press the F or G button to select the
number (“USER1/2/3”) in which you
want to save the setting, and then press
the ENTER button. The confirmation
screen will then be displayed. Select
“OK” to save the setings. The letters
“PROFILE SAVE” will flash red while
saving the settings.
NOTE:
B Do not turn off the power while the settings are being saved (it takes
about 5 seconds to save the settings).
B After saving the adjusted settings, the “PROFILE” setting will
automatically change to the setting saved in the “PROFILE SAVE”
menu. If you continue to adjust colors to make other profiles, change
the “PROFILE” setting to “NORMAL” manually.
B When the “COLOR MNGMT” menu is closed, or if the “PROFILE” settings
are changed before the adjusted color settings have been saved, the
“PROFILE SAVE” confirmation screen will be displayed. However, if you
change the input signals, the adjusted color settings will not be saved.
Retrieving the saved picture
settings (USER MEMORY)
If you have saved the adjusted picture settings using the “MEMORY SAVE”
menu, you can retrieve the saved picture settings.
Press the USER MEMORY button.
MEMORY LOAD
MEMORY 1
MEMORY 2
MEMORY 3
SELECT
ENTER
ESC
BPress the F or G button to select the setting
you want to retrieve, then press the ENTER
button.
NOTE:
B Only the settings saved in the “MEMORY SAVE” menu will be
displayed in the “MEMORY LOAD” menu. (Refer to page 42.)
ENGLISH-35
Useful functions
NOTE:
B The projected image will be paused when the cursor is displayed.
Press the MENU button to cancel the still image. (If the adjustment
menu is displayed, press the MENU button twice.)
B When there are same or similar colors in the projected image, these
colors will also be changed.
B The colors white, gray and black cannot be adjusted.
B If the same colors are adjusted separately, these colors may not be
adjusted to suit your preference.
B You can adjust a maximum of 8 colors (“PT.1-8”) for each user
(“USER1/2/3”). The cursor will not be displayed when 8 colors have
already been adjusted.
On-screen menus
Menu screens
The various settings and adjustments for this projector can be carried out by
selecting the operations from on-screen menus.
The general arrangement of these menus is shown below.
MENU
KEYSTONE
PICTURE
POSITION
SHUTTER
LANGUAGE
OPTION
SELECT
ENTER
EXIT
B Press the MENU button to
display the “MAIN MENU”.
Refer to page 38 for details on
how to operate the on-screen
menus.
KEYSTONE correction (page 28)
KEYSTONE
0
PICTURE menu (page 40)
When an S-VIDEO/VIDEO signal
is being input
POSITION menu (page 44)
When an S-VIDEO/VIDEO/HDMI
signal is being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
DYNAMIC IRIS
ON
ADVANCE MENU
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO
SELECT
ADJ
ESC
POSITION
H-POSITION
0
V-POSITION
0
ASPECT
16:9
SELECT
ENTER
ESC
When a YPBPR/PC/HDMI signal
is being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
DYNAMIC IRIS
ON
ADVANCE MENU
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
525p
SELECT
ADJ
ESC
LANGUAGE menu (page 45)
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT
ENGLISH
ENTER
ESC
When a YPBPR signal is being input
POSITION
H-POSITION
0
V-POSITION
0
CLOCK PHASE
0
ASPECT
4:3
SELECT
ENTER
ESC
When a PC signal is being input
POSITION
H-POSITION
0
V-POSITION
0
DOT CLOCK
0
CLOCK PHASE
0
ASPECT
4:3
AUTO SETUP
SELECT
ENTER
ESC
OPTION menu (page 46)
OPTION
OSD
ON
NR
ON
CINEMA REALITY
ON
BACK COLOR
BLUE
WSS
ON
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
5H
SELECT
ADJ
ESC
SHUTTER function (page 45)
36-ENGLISH
ENGLISH-37
Adjustments and settings
MAIN MENU
Menu operation guide
& Press the F or G button to select an
item, and then press the I or H
button to change or adjust the
setting.
An individual adjustment screen such as
the one shown below will be displayed
for bar scale items.
# Press the MENU button.
BRIGHT
EXIT
The “MAIN MENU” will be
displayed.
$ Press the F or G button to select an item.
Projector control panel
MENU
KEYSTONE
PICTURE
POSITION
SHUTTER
LANGUAGE
OPTION
SELECT
ENTER
38-ENGLISH
The bar scale will turn green when any
adjustment changes the setting from the
factory set value.
For items without any selective arrow or
bar scale, press the ENTER button. The
menu screen for the item will then be
displayed.
This projector has
unadjustable items and
unusable functions
depending on the signal
being input.
When an item cannot be
adjusted or a function cannot
be used, the corresponding
on-screen menu display
does not appear, and the
item or function will not work
even if the ENTER button is
pressed.
Returning a setting to the factory default
EXIT
Selected item will be displayed in
blue.
% Press the ENTER button to accept the
selection.
PICTURE
NOTE:
B Press the MENU
button to return to
the previous
screen.
0
Unavailable onscreen menu items
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
DYNAMIC IRIS
ON
ADVANCE MENU
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO
SELECT
ADJ
ESC
The selected menu screen or
adjustment screen will then be
displayed. (Example: “PICTURE”
menu)
If you press the NORMAL button on the remote control unit, you can return
settings to the factory default settings. However, the operation of this function
varies depending on which screen is being displayed.
B When a menu screen is being displayed
All items displayed will be returned to their factory default settings, and the
bar scale will appear white.
B When an individual adjustment screen is being displayed
Only the item displayed will be returned to the factory default setting, and
the bar scale will appear white.
NOTE:
B Triangle symbols above and below the
bar scale indicate the factory default
setting. Items which do not have these
triangle symbols cannot be returned to
the factory default setting.The positions
of triangle symbols vary depending on
the type of signal being input.
Indicates the standard
factory default setting
Indicates the current
adjustment value
ENGLISH-39
Adjustments and settings
MENU
KEYSTONE
PICTURE
POSITION
SHUTTER
LANGUAGE
OPTION
SELECT
ENTER
Adjusting the picture
When an S-VIDEO/VIDEO signal is
being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
DYNAMIC IRIS
ON
ADVANCE MENU
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO
SELECT
ADJ
ESC
When a YPBPR/PC/HDMI signal is
being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
DYNAMIC IRIS
ON
ADVANCE MENU
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
525p
SELECT
ADJ
ESC
40-ENGLISH
PICTURE MODE
TINT
ADVANCE MENU
Refer to page 29 for details.
(NTSC/NTSC 4.43/YPBPR/PC/HDMI)
This adjusts the flesh tones in the
picture.
The flesh tones are greenish: I button
The flesh tones are reddish: H button
Picture settings can be adjusted in
more detail.
Press the ENTER button to display
the “ADVANCE MENU”
CONTRAST
This adjusts the contrast of the
picture. (Adjust the “BRIGHT”
setting first if required before
adjusting the “CONTRAST” setting.)
The picture is bright: I button
The picture is dark: H button
BRIGHT
This adjusts the darker areas (black
areas) in the picture.
Black areas are too light: I button
Dark areas are too solid: H button
COLOR
The color is too deep: I button
The color is too pale: H button
NOTE:
B When PC signals are being
input, adjustment can be made
only when 1 125 (1 080)/60i
and 1 125 (1 080)/50i signals
are being input.
NOTE:
B When PC signals are being
input, adjustment can be made
only when 1 125 (1 080)/60i
and 1 125 (1 080)/50i signals
are being input.
SHARPNESS
To soften the picture details:
I button
To sharpen the picture details:
H button
COLOR TEMP.
GAMMA HIGH/MID/LOW
These items are for adjusting the
gradation of the bright, medium and
dark scenes in the projected image
respectively.
CONTRAST R/G/B
COLOR TEMP.
-2
COLOR TEMP.
-1
[
[
COLOR TEMP.
ADVANCE MENU
GAMMA HIGH
0
GAMMA MID
0
GAMMA LOW
0
CONTRAST R
0
CONTRAST G
0
CONTRAST B
0
BRIGHT R
0
BRIGHT G
0
BRIGHT B
0
COLOR MNGMT
SELECT
ENTER
ESC
0
[
COLOR TEMP.
+1
COLOR TEMP.
+2
[
These items are for adjusting the
color temperature of the white areas
of the projected image by changing
each level.
BRIGHT R/G/B
This is used to adjust the white
areas of the picture if they appear
bluish or reddish.
These items are for adjusting the
color temperature of the black areas
of the projected image by changing
each level.
DYNAMIC IRIS
COLOR MNGMT
DYNAMIC IRIS
ON
[
OFF
ON
The amount of light is controlled to
project the images with high
contrast.
OFF
“DYNAMIC IRIS” is disabled.
This item is for adjusting the
selected colors of the projected
image to suit your preference, and
saving the settings. Refer to page
32 for details.
ENGLISH-41
Adjustments and settings
Press the F or G button to select an
item, and then press the I or H
button to change the setting.
For items with bar scales, press the
ENTER button or the I or H button
to display the adjustment screen,
and then press the I or H button to
make the adjustment.
For items without any selective
arrow or bar scale, press the ENTER
button. The menu screen for the item
will then be displayed.
MEMORY LOAD
Press the ENTER button to display
the “MEMORY SAVE” menu.
Press the ENTER button to display
the “MEMORY LOAD” menu.
(If any setting is not saved in the
“MEMORY SAVE” menu, the
“MEMORY LOAD” menu will not be
displayed.)
Refer to page 35 on how to retrieve
the saved settings.
MEMORY SAVE
MEMORY 1
MEMORY 2
MEMORY 3
SELECT
ENTER
ESC
The settings adjusted in “PICTURE”
menu can be saved. Press the F or
G button to select the number
(“MEMORY 1/2/3”) in which you
want to save the setting, and then
press the ENTER button.
The confirmation screen will then be
displayed. Press the I or H button
to select “OK” and then press the
ENTER button.
The current picture setting will be
saved.
MEMORY SAVE
OK
CANCEL
NOTE:
B You can save up to 3 settings
for each of the 2 signal groups
described below (up to 6
settings can be saved).
S-VIDEO, VIDEO, YPBPR,
HDMI (except for VGA480
signals) and 1 125 (1 080)/60i
and 1 125 (1 080)/50i signals
from PCs
VGA480 HDMI signals and PC
[except for 1 125 (1 080)/60i
and 1 125 (1 080)/50i signals]
42-ENGLISH
TV-SYSTEM
(S-VIDEO/VIDEO only)
TV-SYSTEM
AUTO
[
NTSC
[
NTSC4.43
[
PAL
[
PAL-M
[
PAL-N
[
SECAM
This should normally be set to
“AUTO”. If the signal is of such poor
quality that the correct format
cannot be automatically
distinguished, change the setting
manually to the required TV system.
Projecting sRGBcompatible pictures
sRGB is an international color
reproduction standard (IEC61966-21) established by the International
Electrotechnical Commission (IEC).
If you would like the colors in sRGBcompatible pictures to be
reproduced more faithfully, make
the following settings.
# Press the F or G button to
select “PICTURE MODE”, and
then press the I or H button
to select “NATURAL”.
$ Press the NORMAL button on
the remote control unit.
% Press the F or G button to
select “LAMP POWER” in the
“OPTION” menu, and then
press the I or H button to
select “HIGH”.
Adjustments and settings
MEMORY SAVE
NOTE:
B When set to “AUTO”, the
projector automatically
distinguishes between
NTSC/NTSC 4.43/PAL/PAL60/
PAL-M/PAL-N/SECAM signals.
SIGNAL MODE
(PC/YPBPR/HDMI only)
This displays the type of signal
which is currently being projected.
Refer to the list on page 58 for
details on each type of signal.
ENGLISH-43
Adjusting the position
Press the F or G button to select
an item, and then press the I or H
button to change the setting.
For items with bar scales, press the
ENTER button or the I or H button
to display the adjustment screen,
and then Press the I or H button
to make the adjustment.
When an S-VIDEO/VIDEO/HDMI
signal is being input
Horizontal position
(H-POSITION)
To move the picture to the left: I button
To move the picture to the right: H button
Vertical position
(V-POSITION)
To move the picture down: I button
To move the picture up: H button
DOT CLOCK
(PC only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, press the
I or H button to adjust so that any
such noise is minimised.
POSITION
H-POSITION
0
V-POSITION
0
ASPECT
16:9
SELECT
ENTER
ESC
When a YPBPR signal is being input
POSITION
H-POSITION
0
V-POSITION
0
CLOCK PHASE
0
ASPECT
4:3
SELECT
ENTER
ESC
When a PC signal is being input
POSITION
H-POSITION
0
V-POSITION
0
DOT CLOCK
0
CLOCK PHASE
0
ASPECT
4:3
AUTO SETUP
SELECT
ENTER
ESC
CLOCK PHASE
(PC/YPBPR only)
Adjust the “DOT CLOCK” setting first
before carrying out this adjustment.
Press the I or H button to adjust
so that the noise level is least
noticeable.
NOTE:
B If signals with a dot clock
frequency of 100 MHz or higher
are being input, interference
may not be completely
eliminated when the “DOT
CLOCK” and “CLOCK PHASE”
adjustments are carried out.
B When YPBPR signals are being
input, “CLOCK PHASE” can be
adjusted only when
1 125 (1 080)/60i, 1 125
(1 080)/50i, 750 (720)/60p or 750
(720)/50p signals are being input.
(PC only)
“H-POSITION”, “V-POSITION”,
“DOT CLOCK” and “CLOCK
PHASE” are automatically adjusted
according to the input signal.
NOTE:
B When the “ASPECT” is set to
“V SCROLL” (page 30), “AUTO
SETUP” cannot be performed.
ASPECT
Refer to page 30.
Turning off the picture momentarily
(SHUTTER)
The “SHUTTER” function can be used to momentarily turn off the picture
when the projector is not being used for short periods of time. The projector
uses less power in “SHUTTER” mode than it does in normal projection
mode.
# Select “SHUTTER” from the “MAIN MENU” and then press the
ENTER button.
$ Press any button on either the projector or remote control unit
(except the LIGHT button) to return to normal operating mode.
Changing the display language
# Select “LANGUAGE” from the “MAIN MENU” and then press the
ENTER button.
$ Press the F or G button to select a language and then press the
ENTER button.
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT
44-ENGLISH
AUTO SETUP
ENTER
ENGLISH
Indicates the language which is
currently set
ESC
ENGLISH-45
Adjustments and settings
When the input signal is from a
PC, first select “AUTO SETUP”
and then press the ENTER button
to initiate automatic positioning.
If the optimum setting is not
obtained when “AUTO SETUP” is
carried out, adjust by the following
procedure.
Option settings
OPTION
OSD
ON
NR
ON
CINEMA REALITY
ON
BACK COLOR
BLUE
WSS
ON
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
5H
SELECT
ADJ
ESC
OSD
OSD
ON
[
OFF
ON
The signal name is displayed in the
top-right corner of the screen when
the input signal is changed.
OFF
Use this setting when you do not
want the signal name to be
displayed.
NOTE:
B The setting for “TV-SYSTEM”
will also be displayed when an
S-VIDEO/VIDEO signal is being
input.
Noise Reduction (NR)
NR
ON
[
OFF
If the signal is of such poor quality
that picture interference appears,
set “NR” to “ON”. To turn off the
“NR” feature, set to “OFF”.
CINEMA REALITY
[S-VIDEO/VIDEO/PC/HDMI/525i
(480i), 625i(576i), 1 125(1 080)/60i
and 1 125(1 080)/50i YPBPR only]
CINEMA REALITY
ON
[
OFF
ON
Set to “ON” when you would like 24
frames per second pictures (such as
movies) to project the source
faithfully.
OFF
Set to “OFF” when the projected
pictures have problems with
captions or subtitles when the
setting is “ON”.
BACK COLOR
BACK COLOR
BLUE
[
BLACK
This sets the color which is
projected onto the screen when no
signal is being input to the projector.
WSS
WSS
ON
[
FRONT/REAR
FRONT/REAR
LAMP POWER
FRONT
REAR
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 16.)
FRONT
When the projector is placed in front
of a screen.
REAR
When using a translucent screen.
DESK/CEILING
DESK/CEILING
HIGH
[
CEILING
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 16.)
DESK
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
FAN CONTROL
[
LOW
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced.
The “LOW” setting is recommended
for narrow rooms where a high
picture luminance is not essential or
for watching movies.
DESK
OFF
ON
When WSS (Wide Screen
Signalling) is detected from PAL or
625i(576i) YPBPR signals, the
aspect ratio will also be switched
automatically.
OFF
WSS will not be detected from PAL
or 625i(576i) YPBPR signals.
LAMP POWER
[
NORMAL
[
HIGH
Set “FAN CONTROL” to “HIGH”,
when using this projector at high
elevations (above 1 400 m) only.
NOTE:
B “LAMP POWER” cannot be set
when no signal is being input.
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used. When replacing the
lamp unit, follow the instructions on
page 52, and reset “LAMP
RUNTIME” to “0”.
NOTE:
B The lamp’s operating life varies
depending on the usage
conditions (such as the “LAMP
POWER” setting and the
number of times the power is
turned on and off).
NOTE:
B “NR” cannot be set when HDMI
signals are being input.
46-ENGLISH
ENGLISH-47
Adjustments and settings
Press the F or G button to select
an item, and then press the I or H
button to change the setting.
When the TEMP indicator and the
LAMP indicator are illuminated
There are two indicators on the control panel of the projector which give
information about the operating condition of the projector. These indicators
illuminate or flash to warn you about problems that have occurred inside the
projector, so if you notice that one of the indicators is on, turn off the power
and check the table below for the cause of the problem.
LAMP indicator
TEMP indicator
LAMP indicator
Indicator
display
Illuminated (red)
It is nearly time to
Problem replace the lamp
unit.
Flashing (red)
An abnormality has been detected in the lamp
circuit.
TEMP indicator
Indicator
display
Illuminated (red)
(Lamp unit on)
The surrounding temperature or
the temperature inside the
projector has become unusually
Problem high.
Flashing (red)
(Lamp unit off)
The surrounding temperature or
the temperature inside the
projector has become
dangerously high, causing the
lamp unit to automatically shut
off.
B The ventilation holes may be covered.
Possible
B The ambient temperature in the place of use may be too high.
cause
B The air filter may be blocked.
B Uncover the ventilation holes.
B Set up the projector in a place where the temperature is
between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is
between 20% and 80% (with no condensation). [If you set the
“FAN CONTROL” to “HIGH” (page 47), set up the projector in a
Remedy
place where the temperature is between 0 °C (32 °F) and 35 °C
(95 °F) and the humidity is between 20% and 80% (with no
condensation).]
B Turn off the MAIN POWER switch by following the procedure
on page 26, and then clean the air filter (refer to page 50).
48-ENGLISH
B This occurs when B Wait for a while
B Turn off the MAIN
the operation time
until the lamp unit
POWER switch by
for the lamp unit is
cools down before
following the
nearing 2 700
turning the power
procedure given
hours (when
back on again.
on page 26, and
“LAMP POWER”
then contact an
has been set to
Authorized
“HIGH”
and
when
Service Center.
Remedy
“DYNAMIC IRIS”
has been set to
“ON”). Ask your
dealer or an
Authorized
Service Center to
replace the lamp
unit.
NOTE:
B Be sure to turn off the MAIN POWER switch by following the procedure
given in “Turning off the power” on page 26 before carrying out any of
the procedures in the “Remedy” column.
B If the power turns off after the TEMP indicator has illuminated, it means
an abnormality has occurred. Please contact an Authorized Service
Center so that the necessary repairs can be made.
ENGLISH-49
Care and maintenance
B Does “REPLACE B The power may
B There may be an
LAMP” appear on
have been turned
abnormality in the
Possible
the screen after
on straight away
lamp circuit.
cause
the projector is
after it was turned
turned on?
off.
Cleaning and replacing the air filter
Replacing the lamp unit
If the air filter becomes clogged with dust, the internal temperature of the
projector will rise, the TEMP indicator will illuminate and the projector’s
power will turn off (the TEMP indicator will flash after the power is turned off).
The air filter should be cleaned every 100 hours of use.
Warning
& Clean the air filter.
Use a vacuum cleaner to clean
off any accumulated dust.
Notes on replacing the lamp
unit
' Install the air filter.
NOTE:
B Place the projector on top of a
soft cloth so that it will not
become scratched.
% Remove the air filter.
Put your fingernails under the air
filter and pull the air filter out of
the projector.
Air filter
50-ENGLISH
NOTE:
B Be sure to install the air filter
before using the projector. If
the projector is used without
the air filter installed, dust and
other foreign particles will be
drawn into the projector, and
malfunctions will result.
B If the dust cannot be removed
by cleaning, it is time to
replace the air filter. Please
consult your dealer.
Furthermore, if the lamp unit is
being replaced, replace the air
filter at this time also.
B The light generating lamp is
made of glass, so dropping it or
allowing it to hit hard objects may
cause it to burst. Be careful when
handling the lamp.
B Dispose of the removed old lamp
with the same care that would be
taken with a fluorescent light.
B A Phillips screwdriver is
necessary for removing the lamp
unit.
NOTE:
B The projector is not supplied
with a replacement lamp unit.
Please ask your dealer for
details. Lamp unit product
no.: ET-LAE700
CAUTION:
B Do not use any lamp unit other
than the one with the product
number indicated above.
Lamp unit replacement
period
The lamp is a consumable product.
Even when the full life of the bulb has
not been exhausted, the brightness
of the light will gradually decline.
Therefore periodic replacement of
the lamp is necessary.
The intended lamp replacement
interval is 3 000 hours, but it is
possible that the lamp may need to
be replaced earlier due to variables
such as a particular lamp’s
characteristics, usage conditions and
the installation environment.
Early preparation for lamp
replacement is encouraged.
The lamp will automatically shut off
after approximately 30 minutes when
3 000 hours of use have been
reached because of a much greater
chance of it exploding after this time.
NOTE:
B The usage hours explained
above are for when “LAMP
POWER” in the “OPTION”
menu has been set to “HIGH”
and when “DYNAMIC IRIS” in
the “PICTURE” menu has
been set to “ON”. When
“LAMP POWER” has been set
to “HIGH” and “DYNAMIC
IRIS” has been set to “OFF”,
the usage hours will be 2 000
hours. If “LAMP POWER” is
set to “LOW”, the brightness of
the lamp will be less and life of
the lamp can be extended.
B While 3 000 hours is the
intended replacement interval,
it is not a period of time
covered by warranty.
ENGLISH-51
Care and maintenance
# Turn off the MAIN POWER
switch and disconnect the
power cord plug from the wall
outlet.
Turn off the MAIN POWER switch
according to the procedure given
in “Turning off the power” on page
26 before disconnecting the power
cord plug from the wall outlet.
$ Gently turn the projector
upside down.
The lamp unit should only be
replaced by a qualified
technician.
When replacing the lamp, allow it
to cool for at least one hour
before handling it.
B The lamp cover gets very hot,
and touching it can cause burns.
Displayed for 30
seconds. Pressing any
More than 2 700 hours*
button will clear the
display.
More than 3 000 hours*
Remains displayed until
any button is pressed.
LAMP indicator
Illuminates red during
image projection and
standby mode.
* These periods of time may become shorter according to the settings of the projector.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 3 000 hours (when “LAMP POWER” has been
set to “HIGH” and when “DYNAMIC IRIS” has been set to “ON”), the projector will
switch to standby mode after approximately 30 minutes of operation. The steps
) to - on the next page should thus be completed within 30 minutes.
# Turn off the MAIN POWER
switch according to the
procedure given in “Turning off
the power” on page 26, and
then disconnect the power
cord plug from the wall outlet
and check that the area around
the lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover.
Lamp unit cover
Lamp unit cover fixing screws
52-ENGLISH
% Use a Phillips screwdriver to
loosen the two lamp unit fixing
screws until the screws turn
freely. Then hold the handle of
the lamp unit and gently pull it
out from the projector.
Lamp unit fixing screws
A
B
Handle
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
When inserting the new lamp
unit, be sure to push it in at the
point A and B .
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
( Insert the power cord plug into
the wall outlet and then press
the MAIN POWER switch.
) Press the POWER button so
that a picture is projected onto
the screen.
* Press the MENU button to
display the “MAIN MENU”, and
then press the F or G button
to select “OPTION”.
MENU
KEYSTONE
PICTURE
POSITION
SHUTTER
LANGUAGE
OPTION
SELECT
ENTER
EXIT
+ Press the ENTER button to
display the “OPTION” menu,
and then press the F or G
button to select “LAMP
RUNTIME”.
OPTION
OSD
ON
NR
ON
CINEMA REALITY
ON
BACK COLOR
BLUE
WSS
ON
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
2720H
SELECT
ESC
, Press and hold the ENTER
button for approximately 3
seconds.
OPTION
OSD
ON
NR
ON
CINEMA REALITY
ON
BACK COLOR
BLUE
WSS
ON
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
TIME RESET [POWER OFF]
SELECT
ESC
The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
- Turn off the power.
This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 26 for details on
how to turn off the power.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover
securely. If they are not
securely installed, it may cause
the protection circuit to operate
so that the power cannot be
turned on.
ENGLISH-53
Care and maintenance
On-screen display
Before calling for service
Before calling for service, check the following points.
54-ENGLISH
Page
–
–
–
48
49
–
–
25
40
45
–
25
17
–
17
40,
41
–
–
23
23
Page
Problem
Possible cause
Picture from
–
B The cable may be too long.
computer does B The external video output for the laptop computer
–
not appear.
may not be set correctly.
(You may be able to change the external output
settings by pressing the [Fn]+[F3] or [Fn]+[F10]
keys simultaneously. The actual method varies
depending on the type of computer, so refer to the
documentation provided with your computer for
further details.)
Cleaning and maintenance
Before carrying out cleaning and maintenance, be
sure to disconnect the power cord plug from the
wall outlet.
Wipe the cabinet with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water with a small amount
of neutral detergent in it, squeeze the cloth very well, and then wipe the
cabinet. After cleaning, wipe the cabinet dry with a dry cloth. If using a
chemically-treated cloth, read the instructions supplied with the cloth before
use.
Do not wipe the lens with a cloth that is dusty or which produces lint.
If any dust or lint gets onto the lens, such dust or lint will be magnified and
projected onto the screen. Use a blower to clean any dust and lint from the
lens surface, or use a soft cloth to wipe off any dust or lint.
23
42
–
58
ENGLISH-55
Care and maintenance
Problem
Possible cause
Power does not B The power cord may not be connected.
turn on.
B The MAIN POWER switch is turned off.
B The main power supply is not being supplied to the
wall outlet.
B TEMP indicator is illuminated or flashing.
B LAMP indicator is illuminated or flashing.
B The lamp unit cover has not been securely
installed.
No picture
B The video signal input source may not be
appears.
connected properly.
B The input selection setting may not be correct.
B The “BRIGHT” adjustment setting may be at the
minimum possible setting.
B The “SHUTTER” function may be in use.
The picture is B The lens cover may still be attached to the lens.
fuzzy.
B The lens focus may not have been set correctly.
B The projector may not be at the correct distance
from the screen.
B The lens may be dirty.
B The projector may be tilted too much.
The color is
B “COLOR” or “TINT” adjustment may be incorrect.
pale or grayish.
B The input source which is connected to the
projector may not be adjusted correctly.
The remote
B The batteries may be weak.
control unit
B The batteries may not be inserted correctly.
does not
B The remote control signal receptor on the projector
operate.
may be obstructed.
B The remote control unit may be out of the
operation range.
The picture does B The signal format (“TV-SYSTEM”) may not be set
not display
correctly.
correctly.
B There may be a problem with the video tape or
other signal source.
B A signal which is not compatible with the projector
may be being input.
Specifications
Amps:
LCD panel:
Panel size (diagonal):
Aspect ratio:
Display method:
Drive method:
Pixels:
Lens:
100 V - 240 V ~, 50 Hz/60 Hz
180 W [During standby (when fan is
stopped): Approx. 3.0 W]
2.2 A - 1.1 A
0.7 type (17.78 mm)
16:9
3 transparent LCD panels (RGB)
Active matrix method
921 600 (1 280 x 720) x 3 panels
Manual zoom (1 - 2.0) / Manual focus
F 1.9 - 3.1, f 21.7 mm - 43.1 mm
Lamp:
UHM lamp (130 W)
Luminosity:
1 000 lm
Scanning frequency(for RGB signals):
Horizontal scanning frequency: 30 kHz - 70 kHz
Vertical scanning frequency: 50 Hz - 87 Hz
Dot clock frequency:
Less than 100 MHz
YPBPR signals:
525i (480i), 525p (480p), 625i (576i),
625p (576p), 1 125 (1 080)/60i,
1 125 (1 080)/50i, 750 (720)/60p,
750 (720)/50p
Color system:
7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/
PAL60/SECAM)
Projection size:
1 016 mm - 5 080 mm (40˝ - 200˝)
Throw distance:
1.2 m - 12.4 m (3´11˝ - 40´8˝)
Screen aspect ratio:
16:9
Installation:
Front/Rear/Ceiling/Desk (Menu selection
method)
Connectors
S-VIDEO IN:
Single-line, Mini DIN 4-pin
Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Ω
VIDEO IN:
Single-line, RCA pin jack
1.0 V [p-p], 75 Ω
PC IN:
RGB:
Single-line, D-sub HD 15-pin (female)
R.G.B.:
0.7 V [p-p], 75 Ω
G.SYNC:
1.0 V [p-p], 75 Ω
HD/SYNC:
TTL high impedance, automatic
positive/negative polarity compatible
VD:
TTL high impedance, automatic
positive/negative polarity compatible
56-ENGLISH
COMPONENT IN:
Y, PB/CB, PR/CR
Y:
PB,PR (CB,CR):
HDMI IN:
TRIGGER out:
Cabinet:
Dimensions:
Width:
Height:
Length:
Weight:
Operating environment:
Temperature:
Humidity:
Certifications:
<Remote control unit>
Power supply:
Operating range:
Weight:
Dimensions:
Width:
Length:
Height:
<Options>
Ceiling bracket
Projection Screen
Single-line, RCA pin jack x 3
1.0 V [p-p] (Including sync), 75 Ω
0.7 V [p-p], 75 Ω
Single-line, 19-pin HDMI connector
Single-line, M3 jack
When the power is turned on (during
projection) : 12 V
When the power is turned off : 0 V
Moulded plastic (ABS/PC)
335 mm (13-3/16˝)
104 mm (4-3/32˝)
270 mm (10-5/8˝) (Not including lens)
3.6 kg (7.9 lbs.)
0 °C - 40 °C (32 °F - 104 °F)
[When the “FAN CONTROL” is set to “HIGH”
(page 47): 0 °C - 35 °C (32 °F - 95 °F)]
20% - 80% (no condensation)
UL60950, C-UL
FCC Class B
3 V DC (AAA battery x2)
Approx. 7 m (23´) (when operated directly
in front of signal receptor)
70 g (2.5 ozs.) (including batteries)
43 mm (1-11/16˝)
135 mm (5-5/16˝)
22.3 mm (-7/8˝)
ET-PKE700
ET-SRW90CT [width: 2 000 mm(80˝)]
Others
Power supply:
Power consumption:
ENGLISH-57
Appendix
Mode
NTSC/NTSC4.43/
PAL-M/PAL60
PAL/PAL-N/SECAM
525i (480i)
625i (576i)
525p (480p)
625p (576p)
1 125 (1 080)/60i
1 125 (1 080)/50i
750 (720)/60p
750 (720)/50p
VGA480
WIDE480
SVGA
WIDE600
WIDE720
XGA
WIDE768
MXGA
SXGA
WIDE768-2
Display
resolution
(dots)*1
General arrangement of the COLOR MANAGEMENT menu
Scanning
frequency
H
V
(kHz) (Hz)
Dot clock
Picture
frequency
quality*2
(MHz)
Format
720 x 480i
15.7
59.9
A
Video/S-Video
720 x 576i
720 x 480i
720 x 576i
720 x 483
720 x 576
1 920 x 1 080i
1 920 x 1 080i
1 280 x 720
1 280 x 720
640 x 480
640 x 480
640 x 480
640 x 480
856 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1 072 x 600
1 280 x 720
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768
1 280 x 768
1 152 x 864
1 152 x 864
1 280 x 1 024
1 360 x 768
15.6
15.7
15.6
31.5
31.3
33.8
28.1
45.0
45.0
31.5
37.5
43.3
72.1
30.1
35.2
37.9
48.1
46.9
53.7
37.3
45.1
48.4
56.5
60.0
68.7
72.1
45.3
64.0
67.5
64.0
48.8
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
59.9
75.0
85.0
138.0
60.1
56.3
60.3
72.2
75.0
85.1
59.9
60.1
60.0
70.1
75.0
85.0
89.0
56.5
71.2
74.9
60.0
59.8
A
A
A
A
A
AA
AA
AA
AA
A
A
A
A
A
A
A
A
A
A
A
AA
A
A
A
A
A
A
A
A
A
A
Video/S-Video
YPBPR
YPBPR
YPBPR/HDMI
YPBPR/HDMI
YPBPR/PC/HDMI
YPBPR/PC/HDMI
YPBPR/HDMI
YPBPR/HDMI
PC/HDMI
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
25.2
31.5
36.0
62.3
31.5
36.0
40.0
50.0
49.5
56.3
51.4
76.5
65.0
75.0
78.8
94.5
99.2
76.2
94.2
108.0
108.0
73.8
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2 The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture
is projected.
Select “COLOR MNGMT”
from the “ADVANCE MENU”.
Press the COLOR
MANAGEMENT button.
MENU button
COLOR MNGMT
PROFILE
NORMAL
EDIT
SELECT
ADJ
ESC
ENTER button
“PROFILE”
“EDIT”
PROFILE
<EDIT>
NORMAL
[
USER1
EDIT
CURSOR
LOG
PROFILE SAVE
SELECT
ENTER
“CURSOR”
“LOG”
[
USER2
[
USER3
ESC
“PROFILE SAVE”
Readjusting and deleting
Adjusting
LOG
PICTURE MODE:CINEMA1
COLOR
TINT
PT.1
0
0
PT.2
-1
0
PT.3
0
+10
PT.4
-10
+10
PT.5
-6
+5
PT.6
+3
-3
PT.7
0
+7
PT.8
-1
+14
SELECT
ENTER
Saving
BRIGHT
+4
-2
0
-9
+7
+1
+9
-4
PROFILE SAVE
USER 1
USER 2
USER 3
SELECT
ENTER
ESC
ESC
Screen
“CANCEL”
LOG
CHANGE
DELETE
SELECT
CURSOR
COLOUR
TINT
BRIGHT
SELECT
0
0
+2
ADJ
ESC
ENTER
“CHANGE”
ESC
“DELETE”
PROCESSING
“CANCEL”
PROFILE SAVE
OK
CANCEL
PROFILE SAVE
If “OK” is selected, the screen
display will return to <EDIT>.
DELETE
OK
CANCEL
PROCESSING
If “OK” is selected, the screen
display will return to <EDIT>.
Screen
Others
List of compatible signals
CURSOR
COLOR
TINT
BRIGHT
SELECT
0
0
+2
ADJ
ESC
PROCESSING
58-ENGLISH
ENGLISH-59
Dimensions
Projection dimensions calculation methods
<Units: mm (inch)>
Dimensions such as projection distances can be calculated from the screen
diagonal length. (Units for calculations: m)
84 (3-9/32˝)
104 (4-3/32˝)
SW
Screen Width: SW=SDx0.872
Screen Height: SH=SDx0.490
Minimum Projection Distance: LW=1.2244xSD-0.056
Maximum Projection Distance: LT=2.4449xSD-0.056
*The values obtained from the formulas above are approximate.
270 (10-5/8˝)
LW/LT
54 (2-1/8˝)
SH
SD
255 (10-1/32˝)
16:9
82.9 (3-1/4˝)
Others
335 (13-3/16˝)
60-ENGLISH
ENGLISH-61
Trademark acknowledgements
B VGA and XGA are trademarks of International Business Machines
Corporation.
B S-VGA is a registered trademark of the Video Electronics Standards
Association.
B HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
All other trademarks are the property of the various trademark owners.
These Operating Instructions are printed on recycled paper.
62-ENGLISH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement