Panasonic WV-SF332 Installation Guide

Panasonic WV-SF332 Installation Guide
Installation Guide
Network Camera
WV-SF336, WV-SF335
WV-SF332
WV-SF336E, WV-SF335E
WV-SF332E
Model No.
WV-SF336
(This illustration represents WV-SF336.)
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
WARNING:
• Apparatus shall be connected to a mains socket outlet with a protective earthing connection.
• The mains plug or an appliance coupler shall
remain readily operable.
• To prevent fire or electric shock hazard, do not
expose this apparatus to rain or moisture.
• The apparatus should not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, should be placed
on the apparatus.
• All work related to the installation of this product should be made by qualified service personnel or system installers.
• For PERMANENTLY CONNECTED
APPARATUS provided neither with an all-pole
MAINS SWITCH nor an all-all pole circuit
breaker, the installation shall be carried out in
accordance with all applicable installation
rules.
• The connections should comply with local
electrical code.
UL listed model No:
WV-SF336, WV-SF335, WV-SF332
For Canada
This Class A digital apparatus complies with
Canadian ICES-003.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
For U.S.A
NOTE: This equipment has been tested and
found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area
is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral
devices). Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
Power disconnection. Unit with or without ON-OFF
switches have power supplied to the unit whenever the power cord is inserted into the power
source; however, the unit is operational only when
the ON-OFF switch is in the ON position. Unplug
the power cord to disconnect the main power for
all units.
2
For U.S.A
The serial number of this product may be found
on the surface of the unit.
You should note the model number and serial
number of this unit in the space provided and
retain this book as a permanent record of your
purchase to aid identification in the event of
theft.
Model No.
Serial No.
We declare under our sole responsibility that the product
to which this declaration relates is in conformity with the
standards or other normative documents following the
provisions of Directives 2006/95/EC and 2004/108/EC.
Wir erklären in alleiniger Verantwortung, daß das Produkt,
auf das sich diese Erklärung bezieht, mit den folgenden
Normen oder normativen Dokumenten übereinstimmt.
Gemäß den Bestimmungen der Richtlinie 2006/95/EC
und 2004/108/EC.
Nous déclarons sous notre propre responsabilité que le
produit auquel se réfère la présente déclaration est
conforme aux normes spécifiées ou à tout autre
document normatif conformément aux dispositions des
directives 2006/95/CE et 2004/108/CE.
Nosotros declaramos bajo nuestra única responsabilidad
que el producto a que hace referencia esta declaración
está conforme con las normas u otros documentos
normativos siguiendo las estipulaciones de las directivas
2006/95/CE y 2004/108/CE.
Noi dichiariamo sotto nostra esclusiva responsabilità che
il prodotto a cui si riferisce la presente dichiarazione
risulta conforme ai seguenti standard o altri documenti
normativi conformi alle disposizioni delle direttive
2006/95/CE e 2004/108/CE.
Wij verklaren als enige aansprakelijke, dat het product
waarop deze verklaring betrekking heeft, voldoet aan de
volgende normen of andere normatieve documenten,
overeenkomstig de bepalingen van Richtlijnen 2006/95/
EC en 2004/108/EC.
Vi erklærer os eneansvarlige for, at dette produkt, som
denne deklaration omhandler, er i overensstemmelse
med standarder eller andre normative dokumenter i følge
bestemmelserne i direktivene 2006/95/EC og 2004/108/
EC.
Vi deklarerar härmed vårt fulla ansvar för att den produkt
till
vilken
denna
deklaration
hänvisar
är
i
överensstämmelse med de standarder eller andra
normativa dokument som framställs i direktiv nr 2006/95/
EC och 2004/108/EC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota
tämä ilmoitus koskee, noudattaa seuraavia standardeja
tai muita ohjeellisia asiakirjoja, jotka noudattavat
direktiivien 2006/95/EC ja 2004/108/EC säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse
med følgende normer eller andre normgivende
dokumenter som følger bestemmelsene i direktivene
2006/95/EC og 2004/108/EC.
3
Contents
Important safety instructions.......................................................................................................... 5
Limitation of liability........................................................................................................................ 6
Disclaimer of warranty.................................................................................................................... 6
Preface........................................................................................................................................... 7
Main functions................................................................................................................................ 7
About notations.............................................................................................................................. 7
About the user manuals................................................................................................................. 8
System requirements for a PC....................................................................................................... 9
Trademarks and registered trademarks....................................................................................... 10
About copyright and license........................................................................................................ 10
Network security.......................................................................................................................... 10
Precautions.................................................................................................................................. 11
Precautions for Installation........................................................................................................... 14
Major operating controls.............................................................................................................. 16
Detaching the dome cover........................................................................................................... 18
Preparations................................................................................................................................. 19
Insert/remove an SDHC/SD memory card................................................................................... 22
Connection................................................................................................................................... 23
Installation.................................................................................................................................... 28
Adjustment................................................................................................................................... 29
Attaching the dome cover............................................................................................................ 34
Configure the network settings.................................................................................................... 36
Troubleshooting............................................................................................................................ 38
Specifications............................................................................................................................... 39
Standard accessories................................................................................................................... 42
Optional accessories.................................................................................................................... 42
4
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
5
Limitation of liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Disclaimer of warranty
IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT
OPERATION OF THE USER;
(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE
USER;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION
BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME
REASON, BECOMES PUBLIC OR IS USED FOR THE PURPOSE OTHER THAN
SURVEILLANCE;
(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
6
Preface
The network cameras WV-SF330 series are designed to operate using a PC on a network
(10BASE-T/100BASE-TX).
By connecting to a network (LAN) or the Internet, images and audio from the camera can be monitored on a PC via a network.
WV-SF336
• Maximum image capture size (1 280 x 960 (Aspect ratio of 4:3), 1 280 x 720 (Aspect ratio of
16:9))
• Compatible with the auto focus (AF) function
WV-SF335
• Maximum image capture size (1 280 x 960 (Aspect ratio of 4:3), 1 280 x 720 (Aspect ratio of
16:9))
• Compatible with the focus assist (F. A.) function
WV-SF332
• Maximum image capture size (800 x 600 (Aspect ratio of 4:3), 640 x 360 (Aspect ratio of 16:9))
• Compatible with the focus assist (F. A.) function
Note:
• It is necessary to configure the network settings of the PC and its network environment to
monitor images from the camera on the PC. It is also necessary to install a web browser on the
PC.
About notations
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
SF336
The functions with this notation are available when using the model WV-SF336.
SF335
The functions with this notation are available when using the model WV-SF335.
SF332
The functions with this notation are available when using the model WV-SF332.
Main functions
H.264/MPEG-4 and JPEG triple encoding
H.264/MPEG-4 dual stream output and JPEG output can be simultaneously provided.
* Either H.264 or MPEG-4 is selectable.
Wide dynamic range function
This function compensates brightness so that it produces clearer images even if objects have various illumination intensities.
7
Important:
• When the wide dynamic range function is activated, noise may be increased in the dark area of
the object.
Auto focus (AF) function SF336
It is possible to adjust the focus automatically by moving the focus ring of the lens with the operation button of this camera or the setup menu.
Focus assist (F. A.) function SF335
SF332
During the manual focus adjustment, this function indicates the best focus position.
Power over Ethernet function
When connecting with a PoE (Power over Ethernet) device, power will be supplied by simply connecting a LAN cable. (IEEE802.3af compliant)
Interactive communication with audio
By using the audio output connector and the microphone in connector, receiving audio from the
cameras on a PC and transmitting audio from the PC to the cameras is available.
SDHC/SD memory card slot equipped
It is possible to save H.264 videos and JPEG images on the SDHC/SD memory card manually at
an alarm occurrence or on a web browser.
It is also possible to save JPEG images at a network failure occurrence. (Download is possible.)
* Recommended SDHC/SD memory card (☞ page 42)
About the user manuals
There are 2 sets of operating instructions for the WV-SF336, WV-SF335, WV-SF332 (NTSC model),
WV-SF336E, WV-SF335E, WV-SF332E (PAL model) as follows.
• Installation Guide: Explains how to install and connect devices.
• Operating Instructions (PDF): Explains how to perform the settings and how to operate this
camera.
Adobe® Reader® is required to read these operating instructions (PDF) on the provided CD-ROM.
When the Adobe® Reader® is not installed on the PC, download the latest Adobe® Reader® from
the Adobe web site and install it.
"WV-SF336, WV-SF335, WV-SF332" or "SF336, SF335, SF332" shown in the instructions and illustrations used in these operating instructions indicates the WV-SF336, WV-SF335, WV-SF332,
WV-SF336E, WV-SF335E, WV-SF332E.
The screens used in these operating instructions show the cases of NTSC models.
8
System requirements for a PC
CPU:
Memory:
Network Interface:
Audio Interface:
Monitor:
OS:
Web browser:
Other:
Intel® CoreTM2 Duo 2.4 GHz or faster recommended
512 MB or more (A minimum of 1 GB memory is required when using
Microsoft® Windows® 7 or Microsoft® Windows Vista®.)
10BASE-T/100BASE-TX 1 port
Sound card (when using the audio function)
Image capture size:
1 024 x 768 pixels or more
Color:24-bit True color or better
Microsoft® Windows® 7 Professional (64-bit)
Microsoft® Windows® 7 Professional (32-bit)
Microsoft® Windows Vista® Business SP1 (32-bit)
Microsoft® Windows® XP Professional SP3
Windows® Internet Explorer® 8.0
(Microsoft® Windows® 7 Professional (32-bit/64-bit))
Windows® Internet Explorer® 7.0
(Microsoft® Windows Vista® Business SP1 (32-bit))
Microsoft® Internet Explorer® 6.0 SP3
(Microsoft® Windows® XP Professional SP3)
CD-ROM drive
(It is necessary to read the operating instructions and use the software on
the provided CD-ROM.)
DirectX® 9.0c or later
Adobe® Reader®
(It is necessary to read the operating instructions on the provided
CD-ROM.)
Important:
• When using a PC that does not meet the above requirements, displaying of images may
become slower or the web browser may become inoperable.
• Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted
depending on the network environment.
• Microsoft® Windows® XP Professional 64-bit Edition is not supported.
• When using IPv6 for communication, use Microsoft® Windows® 7 or Microsoft® Windows
Vista®.
Note:
• Refer to "Notes on Windows Vista® / Windows® 7" (PDF) for further information about system
requirements for a PC and precautions when using Microsoft® Windows® 7 or Microsoft®
Windows Vista®.
9
Trademarks and registered trademarks
• Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX and DirectX are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Intel and Intel Core are trademarks or registered trademarks of Intel Corporation in the United
States and other countries.
• Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
• SDHC logo is a trademark.
• Other names of companies and products contained in these operating instructions may be
trademarks or registered trademarks of their respective owners.
About copyright and license
Distributing, copying, disassembling, reverse compiling, reverse engineering, and also exporting in
violation of export laws of the software provided with this unit are expressly prohibited.
Network security
As you will use this unit connected to a network, your attention is called to the following security
risks.
q Leakage or theft of information through this unit
w Use of this unit for illegal operations by persons with malicious intent
e Interference with or stoppage of this unit by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.
• Use this unit in a network secured by a firewall, etc.
• If this unit is connected to a network that includes PCs, make sure that the system is not infected by computer viruses or other malicious entities (using a regularly updated anti-virus program, anti-spyware program, etc.).
• Protect your network against unauthorized access by restricting users to those who log in with
an authorized user name and password.
• Apply measures such as user authentication to protect your network against leakage or theft of
information, including image data, authentication information (user names and passwords),
alarm mail information, FTP server information and DDNS server information.
• After the unit is accessed by the administrator, make sure to close the browser for added security.
• Change the administrator password periodically for added security.
• Do not install the camera in locations where the camera or the cables can be destroyed or
damaged by persons with malicious intent.
10
Precautions
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may cause fire,
electric shock, injury, or damage to the product.
Be sure to consult the dealer.
Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of this product
may occur.
Stop the operation immediately when
something is wrong with this product.
When smoke goes up from this product or the
smell of smoke comes from this product, stop
the operation immediately and contact your
dealer.
Turn the power off immediately and contact
qualified service personnel for service.
The exclusively designed mount bracket
shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for
installation.
Do not attempt to disassemble or modify
this product.
Failure to observe this may cause fire or electric
shock.
Consult the dealer for the repair or inspections.
Do not insert any foreign objects.
This could permanently damage the apparatus.
Turn the power off immediately and contact
qualified service personnel for service.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface
may cause the product to fall down or topple
over, resulting in injury.
Installation work shall be started after sufficient
reinforcement.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a
fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
Do not use this product in an inflammable
atmosphere.
Failure to observe this may cause an explosion
resulting in injury.
The screws and bolts must be tightened to
the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not install this product in locations
subject to vibration.
Loosening of mounting screws or bolts may
cause a fall of the product resulting in injury.
Install this product in a location high
enough to avoid people and objects from
bumping the product.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not strike or give a strong shock to this
product.
Failure to observe this may cause fire or injury.
Do not rub the edges of metal parts with
your hand.
Failure to observe this may cause injury.
Turn the power off when do wiring of this
product.
Failure to observe this may cause electric
shock.
In addition, short circuit or wrong wiring may
cause fire.
11
Turn the power off when cleaning of this
product.
Failure to observe this may cause injury.
[Precautions for use]
This product is designed to be used
indoors. This product is not operable outdoors.
This product has no power switch.
When turning off the power, turn off a circuit
breaker.
To keep on using with stable performance
Do not use this camera in hot and humid conditions for a long time.
Failure to observe this causes component degradation resulting in life shortening of this product.
(Recommended operating temperature: +35 °C
{95 °F} or lower)
Do not expose this camera to direct heat
sources such as a heater.
Do not touch the dome cover with your
bare hands.
A dirty dome cover causes deterioration of picture quality.
Handle this camera with care.
Do not drop this camera, nor apply shock or
vibration to this camera.
Failure to observe this may cause trouble.
About the PC monitor
Displaying the same image on a CRT type
monitor for a long time may damage the monitor. It is recommended to use a screen-saver.
When an error is detected, this product
will restart automatically.
This product will be inoperable for around 2
minutes after the restart just as when the power
is turned on.
12
Product disposal/transfer
Images saved on the SDHC/SD memory card
may lead to personal information leakage.
When it is necessary to dispose or give this
product to someone, even when for repair,
make sure that there is no data on the hard
disk drives.
Cleaning this product body
Be sure to turn off the power before cleaning.
Do not use strong abrasive detergent when
cleaning this camera. Otherwise, it may cause
discoloration. When using a chemical cloth for
cleaning, read the caution provided with the
chemical cloth product.
When the dirt is hard to remove, use a
mild detergent and wipe gently.
When the dirt is hard to remove, use a mild
detergent and wipe gently. Then, wipe off the
remaining detergent with a dry cloth.
Cleaning the lens
Use a lens cleaning paper (used to clean camera lenses or lenses of spectacles). When using
solvent, use an alcohols solvent and do not use
a thinner or a glass cleaner.
Transmission interval
Image transmission interval may become slow
depending on the network environment, PC
performance, shooting subject, access number, etc.
About SDHC/SD memory card
• Before inserting the SDHC/SD memory
card, turn off the power of this product
first. Otherwise, it may cause malfunction
or damage data recorded on the SDHC/
SD memory card. Refer to page 22 for
descriptions of how to insert/remove an
SDHC/SD memory card.
• When using an unformatted SDHC/SD
memory card, format it using this camera.
Recorded data on the SDHC/SD memory
card will be deleted when formatted. If an
unformatted SDHC/SD memory card or an
SDHC/SD memory card formatted with
other devices is used, this product may not
work properly or performance deterioration
may be caused. Refer to the Operating
Instructions (PDF) for how to format a
SDHC/SD memory card.
• When some SDHC/SD memory cards are
used with this product, the product may
not work properly or performance deterioration may be caused. Use the SDHC/SD
memory cards recommended in page 42.
AVC Patent Portfolio License
This product is licensed under the AVC Patent
Portfolio License for the personal and noncommercial use of a consumer to (i) encode video
in compliance with the AVC Standard ("AVC
Video") and/or (ii) decode AVC Video that was
encoded by a consumer engaged in a personal
and non-commercial activity and/or was
obtained from a video provider licensed to provide AVC Video. No license is granted or shall
be implied for any other use. Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
Code label
The code labels (accessory) are required at
inquiry for trouble. Use caution not to lose
these labels. It is recommended to paste one
of the labels onto the CD-ROM case.
Discoloration on the color filter of the
MOS image sensor
When continuously shooting a bright light
source such as a spotlight, the color filter of the
MOS image sensor may have deteriorated and
it may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period,
the discoloration may remain.
MPEG-4 Visual Patent Portfolio License
This product is licensed under the MPEG-4
Visual Patent Portfolio License for the personal
and non-commercial use of a consumer for (i)
encoding video in compliance with the MPEG4 Visual Standard ("MPEG-4 Video") and/or (ii)
decoding MPEG-4 Video that was encoded by
a consumer engaged in a personal and noncommercial activity and/or was obtained from a
video provider licensed by MPEG LA to provide
MPEG-4 Video. No license is granted or shall
be implied for any other use. Additional information including that relating to promotional,
internal and commercial uses and licensing
may be obtained from MPEG LA, LLC. See
http://www.mpegla.com.
13
Precautions for Installation
Installation work shall be performed in accordance with the technology standard of the
electric installation.
This camera is designed to be used
indoors.
This product is not operable outdoors.
Do not expose this camera to direct sunlight for
hours and do not install the product near a
heater or an air conditioner. Otherwise, it may
cause deformation, discoloration and malfunction. Keep this camera away from water and
moisture.
Installing place
Do not place this product in the following places:
• Locations where it may get wet from rain
or water splash
• Locations where a chemical agent is used
such as a swimming pool
• Locations subject to humidity, dust, steam
and oil smoke
• Locations in a specific environment where
a solvent or a flammable atmosphere
exists
• Locations where a radiation, an X-ray, a
strong radio wave or a strong magnetic
field is generated
• Locations where corrosive gas is produced, Locations where it may be damaged by briny air such as seashores
• Locations where the temperature is not
within –10 °C to +50 °C {14 °F to 122 °F}.
• Locations subject to vibrations (This product is not designed for on-vehicle use.)
• Locations subject to condensation as the
result of severe changes in temperature
(In case of installing the camera in such
locations, the dome cover may become
foggy or condensation may be caused on
the cover.)
14
Be sure to remove this product if it is not
in use.
Shielded (STP) LAN cables must be used
with this unit to ensure compliance with
EMC standards. *
* PAL models only
Before installation
• The camera mount bracket described on
page 19 shall be used to mount the camera.
• When this camera and camera mount
bracket are mounted on a ceiling or a wall,
use the screws described on page 19. The
screws to be used are not provided.
Prepare the screws according to the material, structure, strength and other factors of
the mounting area and the total weight of
objects to be mounted.
• Ensure that the mounting surface, anchor
and screws are sufficiently strong.
• Do not mount this product on a plaster
board or a wooden section because they
are too weak. If this product is unavoidably
mounted on such a section, the section
shall be sufficiently reinforced or use an
optional ceiling mount bracket (WV-Q105).
Screw tightening
• The screws and bolts must be tightened
with an appropriate tightening torque
according to the material and strength of
the installation area.
• Do not use an impact driver. Use of an
impact driver may damage the screws or
cause tightening excessively.
• When a screw is tightened, make the
screw at a right angle to the surface. After
tightening the screws or bolts, perform
visual check to ensure tightening is enough
and there is no backlash.
Radio disturbance
When this product is used near TV/radio antenna, strong electric field or magnetic field (near a
motor, a transformer or a power line), images
may be distorted and noise sound may be produced.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with
IEEE802.3af standard.
Router
When connecting this product to the Internet,
use a broadband router with the port forwarding function (NAT, IP masquerade).
Refer to the Operating Instructions (PDF) for
further information about the port forwarding
function.
Time & date setting
It is necessary to set the time & date before
putting this product into operation. Refer to the
Operating Instructions (PDF) for further information about the time & date setting.
15
Major operating controls
Dome cover
Inner dome
Clear dome
(Provided only for service)
Monitor out connector for
service*
Direction marker for installation
Azimuth adjustment ring
Marker
FRONT
TOP
MONITOR
OUT
EXT
Monitor out
connector for
adjustment
(RCA jack)
View from the side
BASE-T/
BASE TX
TOP
LOCK
Tilting table
12V IN
Panning lock screw [LOCK]
12 V DC power supply
terminal
Panning table
* This connector is provided only for service. Do not use the connector for checking the adjustment of the angular field of view on the video monitor.
16
<Side view>
SDHC/SD memory card slot
Access indicator (blinking at accessing)
Link indicator (lighting at linking)
Focus assist (F.A.)
button SF335
SF332
INITIAL SET button
Auto focus (AF)
button SF336
AF
FOCUS
ASSIST
SDHC/SD memory card error
indicator/AF indicator
(Blinks when AF is being
adjusted) SF336
SDHC/SD memory card error
indicator/F.A. indicator
(Lights when the focus assist function
is activated or when the focus ring is
positioned near the best focus position)
Tilting lock screw
SF335
SF332
Audio output connector
External I/O terminals
Microphone/line input connector
NT
FROP
TO
EX
4 3 T I/O
2
1
AUDIO
OUT
MIC/ IN
LINE
SE-T/
10BA ASE-IX
100B
Lens
ITORT
OU
MON
SF336
Network connector
F
Focus lock knob
N
Zoom lock knob
SF335
N
F
About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes
after releasing the button. The camera will start up and the settings including the network settings
will be initialized. Before initializing the settings, it is recommended to write down the settings in
advance.
17
Detaching the dome cover
Important:
• After removal, retain the dome cover fixing screw so as not to lose. The screw is required when
attaching the dome cover. (☞ Page 34)
• Remove the cover film from the dome section of the dome cover after the installation is complete. Do not touch the dome section by hand directly after removing the cover film.
z Remove the dome cover fixing screw (M3,
LOCK OPEN
ADJUST
step screw, x1).
Dome cover fixing screw
(M3, step screw)
x Rotate the dome cover counterclockwise two steps, and align the indication "OPEN" to the
maker of the camera to detach the dome cover.
Marker
OPEN
LOCK
ADJUST
Dome alignment
indication
"OPEN"
LOCK
Dome
cover
Dome section
18
OPEN
ADJUST
Preparations
When installing the camera on a wall or a ceiling, there are four methods as specified below.
(☞ Pages 20 and 21).
• Using the two-gang junction box
• Installing the camera directly on the ceiling or wall
• Using the optional ceiling mount bracket WV-Q168 (for embedded installation on a ceiling)
• Using the optional ceiling mount bracket WV-Q105*1 (for direct mounting on a ceiling)
Important:
• Procure 4 screws (M4) to secure the camera to a wall or a ceiling according to the material of
the installation area. In this case, wood screws and nails should not be used. For mounting a
camera on a concrete wall, use an anchor bolt (for M4) or an AY plug bolt (M4) for securing.
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
• Required pull-out capacity of a single screw/bolt is 196 N {44 lbf} or more.
• If a ceiling board such as plaster board is too weak to support the total weight, the area shall
be sufficiently reinforced or the optional ceiling mount bracket for the camera, WV-Q105, must
be used.
The mounting conditions of the camera are described as follows:
Installation
place
Applicable mount Recommended
bracket
screw
Number of
screw
Minimum pull-out
strength (per 1 pc.)
Ceiling/wall
Two-gang junction
box
M4
4 pcs.
196 N {44 lbf}
Ceiling/wall
(Direct mounting)
M4
4 pcs.
196 N {44 lbf}
Ceiling
WV-Q168 (approx.
280 g {0.8 lbs})
–
–
*2
Ceiling
WV-Q105*1 (approx. –
150 g {0.8 lbs})
–
*2
*1 PAL models only
*2 Make sure that the installed mount bracket can support more than 5 times of the weight of the
camera.
19
Using the side cable access hole
When installing the camera directly on the ceiling or wall with cables exposed or when using the
optional ceiling mount bracket WV-Q168, cut out a portion of the dome cover to open a cable
access hole.
Side cable access hole
Side cable access hole
Method of camera installation
Using the two-gang junction box
Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). (☞ Page 28)
Direction marker for installation
MO
OR
OU
T
I/O
EXT 2 1
4 3
NIT
FR
O
TO NT
P
AU
OUDIO
T
F
E IN 10B
10 AS
0B
A
N
Screws
(locally procured)
MIC
LIN
Two-gang junction box
12
V=
20
IN
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the
cable.
Remove the template label, and mount the camera by fixing 4 screws (locally procured). (☞ Page
28 )
Direction marker for installation
Recommended screw (M4: 4 pcs.)
MO
NIT
OR
OU
T
20 mm {13/16"}
I/O 1
EXT 2
3
Cable access hole for ceiling/wall
4
83.5 mm {3-5/16"}
Side cable access hole
46
{1- mm
13/
40
16"
mm
}
{19/1
6"}
FRO
TO NT
P
AU
D
OU IO
T
N
F
MIC
LIN
E IN 10BA
100BS
A
Screws
(locally procured)
12V
=IN
Installation template label (accessory)
Using the optional ceiling mount bracket WV-Q168
It is possible to reduce the exposed portion of the camera body using the optional ceiling mount
bracket. Refer to WV-Q168 Operating Instructions
or "Installation" (☞ page 28) for how to mount the
camera.
Using the optional ceiling mount
bracket WV-Q105 (PAL models only)
Refer to WV-Q105 Operating Instructions and "Installation" (☞ page 28) for how to mount the camera in case of using the optional ceiling mount bracket.
Roof space
WV-Q105 (option)
Anchor bolt
(4 pcs, WV-Q105 supplied)
Safety wire angle
Cable tie (accessory)
Safety wire
Camera
Ceiling board such
as plaster board
21
Insert/remove an SDHC/SD memory card
Important:
• Before inserting the SDHC/SD memory card, turn off the power of the camera first.
• When inserting an SDHC/SD memory card, make sure the direction.
• Before removing the SDHC/SD memory card, select "Not use" for "SD memory card" on the
[SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and
then unload the SDHC/SD memory card. When the SDHC/SD memory card is inserted or
removed with the power on, data in the SDHC/SD memory card may be damaged.
(☞ Operating Instructions (PDF))
z Detach the dome cover. (☞ Page 18)
SDHC/SD memory card slot
x Insert an SDHC/SD memory card fully into the
SDHC/SD memory card slot.
c Attach the dome cover. (☞ Page 34)
v When
removing the SDHC/SD memory card
from the SDHC/SD memory card slot, detach
the dome cover (☞ page 18), and push the
card until the lock is released. After removal,
attach the dome cover. (☞ Page 34)
Dome cover
Dome cover fixing screw
(M3, step screw)
22
Connection
Caution:
• FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
Before starting the connection, turn off the power of this camera and the devices to be connected.
Check and prepare the required devices and cables for connection.
ø
{1 9 m
1/ m
32
"}
Note:
30
m
• Since the connector storage
m
{1
-3
section does not have a suffi/1
6"
cient space, use audio cables Str
}
S
17 ai
40
30 trai
g
and a LAN cable that do not
m ht
m
m ght
m s
m
m s
{2 ect
exceed the sizes described in
{1
{1 ec
1/ io
-9
-3 tio
32 n
/
/1 n
1
the illustrations.
"}
6"
6"
}
}
Example of
audio cable connector
9 mm
{11/32"}
1/2"}
m{
13 m
Example of LAN cable
connector
z Connect the RCA pin cable to the monitor out connector for adjustment (only used for adjustment of the angular field of view). (☞ Page 16)
Important:
• The monitor out connector for service is provided only for checking the adjustment of the angular field of view on the video monitor when installing the camera or when servicing. It is not provided for recording/monitoring use.
• When checking the adjustment of the angular field of view on the video monitor, be sure to use
the RCA jack of the main body for connection with video monitor.
• Black bands may appear at the top and bottom or right and left of the screen. (That does not
affect the adjustment because the angular field of view is not changed.)
• The video output on the monitor for adjustment does not guarantee the video performance or
image quality.
x Connect
Microphone/line
input connector
T
FRON
TOP
EX
4 3 T I/O
2
1
AUDIO
OUT
MIC/ IN
LINE
-T/
10BASE E-IX
100BAS
OR
MONITOUT
IN
F
the microphone to MIC/LINE IN (for
use of the audio reception function).
Input impedance: Approx. 2 kΩ
Recommended cable length:
1 m {3.3'} or less (for microphone input)
10 m {33'} or less (for LINE input)
Recommended microphone:
Plug-in power type microphone (option)
Connect a monaural mini plug (ø3.5 mm).
• Supply voltage: 2.5 V±0.5 V
• Recommended sensitivity of microphone:
–48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
23
Important:
• Connect/disconnect the audio cables and turn on the power of the camera after turning off the
power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
c Connect
an external speaker with amplifier to
the audio output connector (for use of the audio
transmission function).
Connect a stereo mini plug (ø3.5 mm) (monaural output).
• Recommended cable length: Less than
10 m {33'}
Audio output
connector
T
FRON
TOP
EX
4 3 T I/O
2
1
F
IN
Strip range
the cables of external devices to the
EXT I/O terminal plug (accessory).
q When connecting an external device, remove
8 mm - 9 mm {5/16" - 11/32"} of the outer
jacket of the cable and twist the cable core to
prevent the short circuit first.
Specification of cable (wire): 20 AWG 26 AWG
Single core, twisted
8 mm - 9 mm
{5/16" - 11/32"}
Button
4
3
2
1
e After the cable connection, connect the external I/O terminal plug to the external I/O terminals of the camera.
* Check whether the stripped part of the wire is
not exposed and is securely connected.
External I/O terminal plug
External I/O terminals
<Ratings>
T
FRON
TOP
EX
4 3 T I/O
2
1
r GND
e AUX OUT
-T/
10BASE E-IX
100BAS
OR
MONITOUT
v Connect
w Push down the button of the desired terminal
on the external I/O terminal plug with a ballpoint
pen, and release the button when the cable of
the external device is fully inserted into the terminal hole. Make sure that the cable is firmly
connected to the terminal.
MIC/ IN
LINE
AUDIO
OUT
AUDIO
OUT
OR
MONITOUT
4 3 2 1
24
F
w ALARM OUT
IN
q ALARM IN
MIC/ IN
LINE
-T/
10BASE E-IX
100BAS
Important:
• Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2 wires
or more, use a splitter.
• Connect an external device with verifying that the ratings are within the specifications above.
• When using the EXT I/O terminals as the output terminals, ensure they do not cause signal collision with external signals.
• ALARM OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (50 mA or less)
• ALARM IN
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
b Connect
Network connector
a LAN cable (category 5 or better,
straight, STP*) to the network connector.
* PAL models only
T
FRON
TOP
EX
4 3 T I/O
2
1
AUDIO
OUT
n Connect the power supply.
MIC/ IN
LINE
-T/
10BASE E-IX
100BAS
OR
MONITOUT
Important:
• The 12 V DC power supply shall be insulated
from the commercial AC power.
IN
F
When using 12 V DC power supply
q Loosen the screw of the power cord plug
(accessory).
w Connect the cable of the 12 V DC power supply* to the power cord plug.
Strip 3 mm - 7 mm {1/8" - 9/32"} from the end
of the wire, and twist the stripped part of the
wire sufficiently to avoid short circuit.
Specification of cable (wire):
16 AWG - 24 AWG, Single core, twisted
• Check whether the stripped part of the wire is
not exposed and is securely connected.
e Tighten the screw of the power cord plug.
r Connect the power cord plug to the 12 V DC
power supply terminal.
* FOR UL LISTED MODEL(S), ONLY CONNECT
12 V DC CLASS 2 POWER SUPPLY.
(GND)
(12 V DC)
12 V DC power cord
plug (accessory)
25
Important:
• Be sure to use the power cord plug provided with this product.
• Be sure to fully insert the power cord plug into the 12 V DC power supply terminal (accessory).
Otherwise, it may damage the camera or cause malfunction.
• Be sure to use an AC adaptor compliant with the Specifications regarding power source and
power consumption (☞ page 39).
t Run the 12 V DC output cable through the gap of the cable hook.
12 V DC output cable
Cable hook
12V=
IN
When using PoE (IEEE802.3af compliant)
Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub)
and the network connector of the camera.
* PAL models only
Important:
• Use all 4 pairs (8 pins) of the LAN cable.
• The maximum cable length is 100 m {328'}.
• Make sure that the PoE device in use is compliant with IEEE802.3af standard.
• When connecting both the 12 V DC power supply and the PoE device for power supply, PoE
will be used for power supply.
• When disconnecting the LAN cable once, reconnect the cable after about 2 seconds. When
the cable is quickly connected, the power may not be supplied from the PoE device.
26
Connection example when connecting to a network using a
PoE hub
Speaker with amplifier
(option)
Video monitor
(for adjustment use only)
PoE device (hub)
LAN cable (category 5 or
better, straight, STP*)
Microphone (option)
LAN cable (category 5 or
better, straight, STP*)
Speaker with amplifier
(option)
Microphone (option)
PC
LAN cable (category 5 or
better, straight, STP*)
Video monitor
(for adjustment use only)
<Required cable>
LAN cable (category 5 or better, straight, STP*)
* PAL models only
Important:
• The video monitor is used for checking the adjustment of the angular field of view when installing the camera or when servicing. It is not provided for recording/monitoring use.
• Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
• Power supply is required for each network camera. When using a PoE device (hub), 12 V DC
power supply is unnecessary.
27
Installation
Camera mounting
Installation shall be conducted after turning off each device.
z Detach the dome cover. (☞ Page 18)
x Connect the cables to the camera. (☞ Pages 23 to 27)
As necessary, use a cable tie (accessory) to assemble the cables.
c Mount the camera. (The illustration represents the case in which a two-gang junction box is
installed.)
• Fix the camera with 4 screws (M4, locally procured)
Direction marker for installation
MO
OR
OU
T
I/O
EXT 2 1
4 3
NIT
FR
O
TO NT
P
AU
OUDIO
T
F
E IN 10B
10 AS
0B
A
N
Screws
(locally procured)
MIC
LIN
Two-gang junction box
12
V=
IN
Important:
• When tightening the screws, be careful to ensure that the cables does not tangle the cables.
Note:
• For ceiling mounting
"gFRONT" of direction marker for installation indicates the center of panning. Adjustment of
lens direction will become easier when the camera is mounted with the "gFRONT" marker oriented to the desired shooting area. Refer to the "Adjustment" section (☞ pages 29 to 33) for
further information about adjustment.
• For wall mounting
The camera shall be mounted with the "gFRONT" marker facing upward.
28
Adjustment
z Adjust
the camera angle. When determining the camera angle, repeat fine adjustments by
gradually moving the panning table, tilting table, and azimuth adjustment ring.
Horizontal position (Panning)
Loosen the panning lock screw, rotate the panning table to adjust the pan direction. (Adjustable
range: 350 °)
Panning is possible within the range of 180 ° (when panning clockwise) and 170 ° (when panning
counterclockwise). After adjustment, tighten the panning lock screw to fix the panning table.
(Recommended tightening torque: 0.39 N.m {0.29 lbf·ft})
Home position
* The position where the home
position markers are aligned
FRONT
TOP
EXT
MONITOR
OUT
Home position markers K
Panning table
BASE-T/
BASE TX
Panning lock screw
[LOCK]
TOP
LOCK
12V=IN
Counterclockwise panning
end maker: (Rotation within
the range of 170 °)
Clockwise panning end
marker: (Rotation within the
range of 180 °)
Vertical position (Tilting)
Loosen the tilting lock screws (x2), and rotate
the tilting table to adjust the tilting direction.
(Adjustable range: ±75 °) Since a variable focal
lens is used, it is possible to change the angular field of view. This lens can also be rotated in
the reverse direction, but the image azimuth is
reversed. In this case, the image azimuth can
be modified when the panning table is rotated
to the direction of clockwise panning (180°).
<Lens angular field of view (q Angle)>
Horizontal: 27.7 ° (TELE) to 100.3 ° (WIDE)
Vertical: 20.8 ° (TELE) to 73.5 ° (WIDE)
+75 °
–75 °
Adjustable range
After adjustment, tighten the tilting lock screws (x2) to fix the tilting table.
(Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
29
Note:
• When the camera is used at an angular field of view that is close to horizontal, it must be noted
that the shadow of the dome cover may be projected.
Image tilt adjustment
Rotate the azimuth adjustment ring to adjust the azimuth angle of the image. (Adjustable range:
±100 °)
Adjustable range
–100 °
+100 °
FRONT
TOP
EXT
MONITOR
OUT
BASE-T/
BASE TX
LOCK
12V=IN
x Adjust the angular field of view and the focus.
SF336
Adjust the angular field of view in accordance with the distance between the camera lens and a
photographic subject.
Auto focus (AF)
button
Zoom ring
Zoom lock knob
Focus ring
Loosen
Tighten
q Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appropriate angle of view.
30
w When the auto focus (AF) button on the lateral side of camera is pressed, the auto focus (AF)
indicator will light for around 10 seconds, and the focus is automatically adjusted.
Important:
• Do not move the focus ring.
Note:
• If the zoom lock knob is slightly fastened before the zoom ring is moved, the ring will become
stable to ease the fine adjustment.
• When positioning the zoom ring at a step short of the "T" (or "W") end, the focus adjustment
will be easier.
• When shooting in the following place or the following subjects, focus may not be adjusted
automatically. In this case, adjust the focus manually from the setup menu. Refer to the
Operating Instructions (PDF) for how to perform the manual focus adjustment from the setup
menu.
• Place where the dome easily becomes dirty
• Subj. moving frequently
• Subj. with large illuminance change
• Subj. with low illuminance
• Subj. with reflection or extra brightness
• Subj. through a window
• Subj. with less contrast such as white wall
• Subj. with heavy flicker
31
Adjust the angular field of view and the focus. SF335
SF332
The angular field of view and focus can be adjusted in accordance with the distance between
the camera lens and a photographic subject. These adjustments shall be performed together
with the camera angle adjustment.
FOCUS ADJUSTMENT
Focus assist
(F.A.) button
LOW
HIGH
.......|............
INDICATOR
PEAK HOLD
775
780
BEST
FOCUS
Zoom ring
Zoom lock knob
Focus ring
Focus lock knob
Loosen
Tighten
q Loosen the zoom lock knob and focus lock knob, and adjust the angular field of view in accordance with the photographic subject by moving the zoom lock knob and focus ring.
w Fasten the zoom lock knob.
e Press the focus assist (F.A.) button.
→ "FOCUS ADJUSTMENT" menu will be displayed.
The focus assist function will be activated to perform the optimum adjustment.
r When the focus ring is positioned near the best focus position, the position will automatically
be memorized as the "PEAK HOLD" position. (The closer the focus ring is positioned to the
best focus position, the greater the "PEAK HOLD" value becomes.)
t When the focus ring is moved, the current focus position will be indicated on "INDICATOR".
Adjust the focus position so that the indicator value goes close to the "PEAK HOLD" position.
y When the indicator value goes to the best focus position, "BEST FOCUS" will be displayed in
reverse at the lower right corner of the screen.
u Fasten the focus lock knob so as to fix the best focus position.
i Press the focus assist (F.A.) button again to close the "FOCUS ADJUSTMENT" menu. (No
operation for 3 minutes also closes the menu.)
32
Note:
q When shooting the following subjects, close the "FOCUS ADJUSTMENT" menu by pressing
the focus assist (F.A.) button again, or adjust the focus to obtain the best focus position while
monitoring images from the camera.
• Subj. moving frequently or having large illuminance change
• Subj. with low illuminance
• Subj. with reflection or extra brightness
• Subj. through a window
• Place where the lens easily becomes dirty
• Subj. with less contrast such as white wall
• Subj. with heavy flicker
w If the zoom lock knob is slightly fastened before the zoom ring is moved, the ring will become
stable to ease the fine adjustment.
e If the focus lock knob is slightly fastened before the focus ring is moved, the ring will become
stable to ease the fine adjustment.
r In case the angular field of view has changed during adjustment, close the "FOCUS
ADJUSTMENT" menu once by pressing the focus assist (F.A.) button. (When the angular field
of view changes, the indicator values of "PEAK HOLD" and "INDICATOR" also change.) After
fixing the angular field of view, retry Step 3.
33
Attaching the dome cover
Marker
z Align
the indication "OPEN" to the maker
of the camera to attach the dome cover.
Dome
alignment
indication
"OPEN"
LOCK
OPEN
ADJUST
Dome
cover
Dome section
x Remove
the cover film from the dome
cover except the dome section.
c Adjust
the direction of the inner dome
(☞ page 16).
Rotate the dome cover clockwise to adjust
the marker to "ADJUST". The clear dome
and the inner dome can rotate together in
this state. Rotate the dome section of the
dome cover to adjust the direction so that
no eclipse may be caused.
34
OPEN
LOCK
ST
JU
AD
Important:
• For inner dome adjustments, adjust the marker to the "ADJUST" position. If the dome section
is moved with unreasonable force from the "LOCK" position, this may be a cause of destruction.
v Rotate the dome cover clockwise to adjust
the marker to "LOCK".
OPEN
LOCK
ADJUST
b Fix the dome cover and camera by tightening the dome cover fixing screw (M3, step
screw, x1).
LOCK OPEN
ADJUST
n After
the installation is complete, remove
the cover film, which was removed halfway
in Step 2, completely from the dome section.
Dome cover fixing screw
(M3, step screw)
m Push down the auto focus (AF) button with
a ballpoint pen to adjust the focus again.
SF336
Refer to page 30 for further information
about adjustment.
AF
OPEN
LOCK
ADJUST
Auto focus (AF) button
Important:
• Before pressing the auto focus (AF) button, make sure that the marker is adjusted to the
"LOCK" position. SF336
• When using a model equipped with the focus assist (F. A.) function, defocus may be caused by
the dome cover attached. SF335
SF332
In this case, the focus adjustment will be easier by detaching the dome cover and moving the
focus ring to the "N" direction.
• Before attaching the dome cover, make sure that the subject is present.
35
Configure the network settings
Install the software
Before installing the software, refer to the readme file on the provided CD-ROM first.
Software included on the provided CD-ROM
• Panasonic IP setting software
Configure the network settings of the camera. Refer to the following for further information.
• Viewer Software "Network Camera View 4"
It is necessary to install the viewer software "Network Camera View 4" to display images on a
PC. Install the viewer software by double-clicking the "nwcv4setup.exe" icon on the provided
CD-ROM.
Configure the network settings of the camera using the
Panasonic IP setting software
It is possible to perform the network settings of the camera using the IP setting software on the
provided CD-ROM.
When using multiple cameras, it is necessary to configure the network settings of each camera
independently.
If the Panasonic IP setting software does not work, configure the network settings of the camera
and the PC individually on the "Network" page of the setup menu. Refer to the Operating
Instructions (PDF) for further information.
Important:
• When using Microsoft Windows Vista, the "Windows Security Alert" window may be displayed
when starting the IP setup software. In this case, disable "User Account Control" from the control panel. In this case, disable "User Account Control" from the control panel.
• For the security enhancement, the MAC address/IP address of the camera to be configured will
not be displayed when around 20 minutes have passed after turning on the power of the camera. (When the effective period is set to "20 minutes" in the IP setup)
• Panasonic IP setting software is inoperable in other subnets via the same router.
• This camera cannot be displayed or set with an older version of the IP setting software (version
2.xx).
36
z Start the Panasonic IP setting software.
x Click
the [IP setting] button after selecting the
MAC address/IP address of the camera to be
configured.
Note:
• When using a DHCP server, the IP address
assigned to the camera can be displayed by
clicking the [Refresh] button of the IP setting
software.
• When a duplicate IP address is used, the corresponding MAC address/IP address will be displayed shaded.
c Complete
each network setup item and click
the [Apply] button.
Note:
• When using a DHCP server, it is possible to set
"DNS" to "AUTO".
Important:
• It may take for around 2 minutes to complete to upload the settings to the camera after clicking
the [Apply] button. The settings may be invalidated when the 12 V DC power supply is cut or
when the AC adaptor or the LAN cable is disconnected before completing the upload. In this
case, perform the settings again.
• When using a firewall (including software), allow access to all UDP ports.
37
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the
table or a problem is not described below.
Symptom
Power is not turned on.
38
Cause/solution
When using DC power supply
•Is 12 V DC power supply connect to
the power supply terminal?
→ Check whether the connection is
appropriately established.
•Is the AC adaptor in use compliant with
the Specifications?
→ Check the Specifications regarding
AC adaptor.
When using a PoE device for power
supply
•Are the PoE device and the network
connector on the rear of the camera
connected using a LAN cable (4-pair)?
→ Check whether the connection is
appropriately established.
•Depending on the PoE device, the
power supply will stop when the
demanded power exceeds its total
power limit for all PoE ports.
→ Refer to the operating instructions of
the PoE device in use.
Reference
pages
25 - 26
Specifications
● Basic
Power source:
12 V DC, PoE (IEEE802.3af compliant)
Power consumption:
WV-SF336
12 V DC*: 320 mA, PoE: 4.2 W (Class 2 device)
WV-SF335, WV-SF332
12 V DC*: 280 mA, PoE: 3.5 W (Class 2 device)
* FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC
CLASS 2 POWER SUPPLY.
Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F} (no condensation)
Ambient operating humidity:
Less than 90 %
Monitor output (for adjusting
the angular field of view):
VBS: 1.0 V [p-p]/75 Ω, composite signal, RCA jack
External I/O terminals:
ALARM IN
ALARM OUT
AUX OUT
x1 each
Microphone/Line input:
ø3.5 mm monaural mini jack
Input impedance: Approx. 2 kΩ
For microphone input:
Applicable microphone: Plug-in power type
Supply voltage: 2.5 V ±0.5 V
For line input:
Input level: Approx. –10 dBV
Audio output:
ø3.5 mm stereo mini jack (monaural output)
Output impedance: Approx. 600 Ω
Line level
Dimensions:
ø129.5 mm x 93 mm (H) {5-3/32" x 3-21/32" (H)}
Weight:
WV-SF336: Approx. 410 g {0.82 lbs.}
WV-SF335, WV-SF332: Approx. 370 g {0.82 lbs.}
Finish:
Main body: ABS resin, sail white
Dome section: Clear acrylic resin
● Camera
Image sensor:
1/3 inch-type MOS image sensor
Effective pixels:
Approx. 1.3 megapixels
Scanning area:
4.80 mm (H) × 3.60 mm (V) {3/16" (H) × 5/32" (V)}
Scanning system:
Progressive
Minimum illumination:
WV-SF336 (1 280×960)
WV-SF335 (1 280×960)
Color:0.3 lx {0.03 footcandle} (F1.4, Auto slow shutter: Off
(1/30 s), AGC: High)
0.019 lx {0.0019 footcandle} (F1.4, Auto slow shutter: max. 16/30 s, AGC: High)*
BW:0.2 lx {0.02 footcandle} (F1.4, Auto slow shutter: Off
(1/30 s), AGC: High)
0.013 lx {0.0013 footcandle} (F1.4, Auto slow shutter: max. 16/30 s, AGC: High)*
* Converted value
39
WV-SF332 (800×600)
Color:0.2 lx {0.02 footcandle} (F1.4, Auto slow shutter: Off
(1/30 s), AGC: High)
0.013 lx {0.0013 footcandle} (F1.4, Auto slow shutter: max. 16/30 s, AGC: High)*
BW:0.13 lx {0.013 footcandle} (F1.4, Auto slow shutter:
Off (1/30 s), AGC: High)
0.009 lx {0.0009 footcandle} (F1.4, Auto slow shutter: max. 16/30 s, AGC: High)*
* Converted value
Wide dynamic range:
On/Off
Gain (AGC):
On(Low)/On(Mid)/On(High)/Off
Adaptive black stretch:
On/Off
Light control mode setting:
Indoor scene (50 Hz/60 Hz)/Outdoor scene/Fix shutter
Shutter speed:
Off(1/30), 3/100, 3/120, 2/100, 2/120, 1/100, 1/120, 1/250,
1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000
Auto slow shutter:
Off, Max. 2/30s, Max. 4/30s, Max. 6/30s, Max. 10/30s,
Max. 16/30s
Simple black & white mode:
Off/AUTO
White balance:
ATW1/ATW2/AWC
Digital noise reduction:
High/Low
Video analytics
Face detection:
On/Off (with the XML notification setting)
Privacy zone:
On/Off (up to 2 zones available)
Camera title on screen:
Up to 16 characters (alphanumeric characters, marks)
On/Off
VMD alarm:
On/Off, 4 areas available
● Lens
Focal length:
Maximum aperture ratio:
Angular field of view:
Adjusting angle:
2.8 mm - 10 mm {5/16" - 13/32"}
1:1.3 (WIDE) - 1:3.1 (TELE)
Horizontal: 27.7 ° (TELE) - 100.3 ° (WIDE)
Vertical: 20.8 ° (TELE) - 73.5 ° (WIDE)
Horizontal: 180 ° (clockwise), 170 ° (counterclockwise)
Vertical: ±75 °, Image tilt adjustment range: ±100 °
● Network
Network:
Resolution:
(WV-SF336, WV-SF335)
40
10BASE-T/100BASE-TX, RJ45 connector
Aspect ratio: 4:3
H.2641 280 × 960/VGA (640 × 480)/QVGA (320 × 240),
max. 30 fps
MPEG-4 VGA (640 × 480)/QVGA (320 × 240), max. 30 fps
JPEG1 280 × 960/VGA (640 × 480)/QVGA (320 × 240),
max. 30 fps
Aspect ratio: 16:9
H.264 1 280 × 720/640 × 360/320 × 180, max. 30 fps
JPEG
1 280 × 720/640 × 360/320 × 180, max. 30 fps
* MPEG-4 is not supported.
Resolution:
(WV-SF332)
Aspect ratio: 4:3
H.264800 × 600/VGA (640 × 480)/QVGA (320 × 240), max.
30 fps
MPEG-4 VGA (640 × 480)/QVGA (320 × 240), max. 30 fps
JPEG800 × 600/VGA (640 × 480)/QVGA (320 × 240), max.
30 fps
Aspect ratio: 16:9
H.264 640 × 360/320 × 180, max. 30 fps
JPEG
640 × 360/320 × 180, max. 30 fps
* MPEG-4 is not supported.
Image compression method*1 *2: H.264/MPEG-4
Image quality: Low/Normal/Fine
Transmission type: Unicast/Multicast
Audio bit rate:
Constant bit rate: 64kbps/ 128kbps/ 256kbps/
384kbps/ 512kbps/ 768kbps/ 1024kbps/ 1536kbps/
2048kbps/ 3072kbps/ 4096kbps/ *8192kbps/
Unlimited
* only in H.264 mode
Frame rate priority: 1fps/ 3fps/ 5fps/ 7.5fps/ 10fps/
12fps*/ 15fps/ 20fps/ 30fps
* PAL models only
JPEG
Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/
5 NORMAL/ 6/ 7/ 8/ 9 LOW (10 steps:
0-9)
Transmission type: PULL/PUSH
Transmission interval:
0.1 fps - 30 fps (JPEG frame rate will be restricted when displaying both JPEG and H.264/MPEG-4 images.)
Audio compression method:
G.726 (ADPCM) 32kbps/ 16kbps
Bandwidth control:
Unlimited/ 64kbps/ 128kbps/ 256kbps/ 384kbps/ 512kbps/
768kbps/ 1024 kbps/ 2048kbps/ 4096kbps/ 8192kbps
Protocol:
IPv6: TCP/IP, UDP/IP, HTTP, RTP, FTP, SMTP, DNS, NTP, SNMP
IPv4: TCP/IP, UDP/IP, HTTP, RTSP, RTP, RTP/RTCP, FTP, SMTP,
DHCP, DNS, DDNS, NTP, SNMP
Microsoft Windows 7 Professional (64-bit)
OS*3 *4:
Microsoft Windows 7 Professional (32-bit)
Microsoft Windows Vista Business SP1 (32-bit)
Microsoft Windows XP Professional SP3
Browser:
Windows Internet Explorer 8.0
(Microsoft Windows 7 Professional (32-bit/64-bit))
Windows Internet Explorer 7.0
(Microsoft Windows Vista Business SP1 (32-bit))
Microsoft Internet Explorer 6.0 SP3
(Microsoft Windows XP Professional SP3)
Maximum concurrent access
number:
14 (Depends on network conditions)
FTP client:
Alarm image transmission, FTP periodic transmission (When the
FTP transmission is failed, backup on an optional SDHC/SDC
memory card is available.)
41
Multi-screen:
Compatible SDHC/SD memory
card (option):
Up to 16 camera images can be displayed simultaneously on a
multi-screen.
Manufactured by Panasonic
SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
SD memory card: 256 MB, 512 MB, 1 GB, 2 GB
(except miniSD card and microSD card)
*1 Either H.264 or MPEG-4 is selectable.
*2 Transmission for 2 streams can be individually set in the same compression method.
*3 Refer to "Notes on Windows Vista / Windows 7" (PDF) for further information about system
requirements for a PC and precautions when using Microsoft Windows 7 or Microsoft Windows
Vista.
*4 When using IPv6 for communication, use Microsoft Windows 7 or Microsoft Windows Vista.
Standard accessories
Installation Guide (this document) ............................................... 1 pc.
Warranty card (NTSC model only) ............................................... 1 pc.
CD-ROM*1 ................................................................................. 1 pc.
Code label*2 ............................................................................... 1 pc.
The following parts are used during installation procedures.
Power cord plug ......................................................................... 1 pc.
External I/O terminal plug ........................................................... 1 pc.
Installation template label . .......................................................... 1 pc.
Cable tie ............................................................. 2 pcs. (incl. 1 spare)
*1 The CD-ROM contains the operating instructions (PDFs) and different kinds of tool software
programs.
*2 This label may be required for network management. The network administrator shall retain the
code label.
Optional accessories
Dome cover (Smoke type)
Ceiling Mount Bracket
Ceiling Mount Bracket
*1 PAL models only
42
WV-CF5S
WV-Q168
WV-Q105*1
Information for Users on Collection and Disposal of Old Equipment and used
Batteries
These symbols on the products, packaging, and/or accompanying documents mean that
used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points, in accordance with your national legislation and
the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the environment
which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please
contact your local municipality, your waste disposal service or the point of sale where you
purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or
supplier for further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.
Cd
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies
with the requirement set by the Directive for the chemical involved.
For U.S. and Canadian fields:
For European and other fields:
Panasonic System Networks Company
of America,
Unit of Panasonic Corporation
of North America
Panasonic Corporation
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus,
New Jersey 07094 U.S.A.
http://panasonic.net
Importer's name and address to follow EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg F.R.Germany
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2010
Ns0410-0/1
3TR006433AZA
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement