OWNERS MANUAL
®
+
A
RIUMPH
60/120
Ultra Gain Tube Amps
WARNING: TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. BEFORE USING THIS APPLIANCE,
READ THE OPERATING GUIDE FOR FURTHER WARNINGS.
a
„ULTRA GAIN CALINCHGA м CLEAN GAIN —s ue pe M ey ao FE
ULTRA GAN TUBE AP DR
у 3 7 H | + O: sa
2 = E ; E : Ba
1 a 1 8 1 я ©: 1
igo =o! i 0 0 10 D a 1D
IMPLITE
> 15
7
© ©
п
A 10
Lich
y
=
EA FE] ВАМ aR LEA LD FRESEMCE REYES CFF
1 2 3 4 = 6 7 8 8 9 12 13 14 15
INPUTE ¡ULTRA GAN , DAA GAIN Gen GAIN ; E us E UE priv CEC AE ao FER
, a = a 7 ñ Ч
900:0/0:0:/0: , |0:0:0:0:0:| Zi]
Dn on ú mm о 10 1 с ho
CAM at LOY PRETENSE REYERO SPATLS PONER = :
1 2 3 4 5 6 T 8 g 9 9 10 11 12 13 14 15
HIGH GAIN INPUT (1)
Used for most electric guitars. It is 6 dB louder than the Low Gain input.
LOW GAIN INPUT (2)
Provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the High Gain input.
If both inputs are used simultaneously, the output levels are the same (both are Low Gain).
PRE GAIN (3)
Controls the input volume level of the channel.
POST GAIN (4)
Controls the overall volume level of the channel. The final level adjustment should be made after the desired sound has
been achieved.
PRE GAIN (5)
Controls the input volume level of the channel.
POST GAIN (6)
Controls the overall volume level of the channel. The final level adjustment should be made after the desired sound has
been achieved.
GAIN (7)
Controls the channel volume.
BRIGHT SWITCH (8)
Provides a preset boost to treble frequencies. To activate, depress the switch to its “in” position, The bright function
atfects only the normal channel.
LOW, MID, & HIGH EQ (9)
Passive tone controls that regulate the low, mid and high frequencies, respectively.
PRESENCE (10)
An active tone control that boosts the extreme high frequencies by 6 dB.
MASTER REVERB (11)
Reverberation is an echo effect. Rotate clockwise to increase the effect. Remote footswitch can control On/Off.
STATUS LED (12)
llluminates when amp is switched to standby indicating amplifier is not operational.
POWER LED (13)
llluminates when AC power is being supplied to the amp.
STANDBY SWITCH (14)
Allows amp to be placed in standby or active mode. In standby mode the tubes remain hot, but the amplifier is not
operational.
POWER SWITCH (15)
Depress the switch to the “On” position. The red pilot light (LED) will illuminate indicating power is being supplied to the
unit.
i PRODUC TOF PEANEY TLECTADMICE CORP Ea
EIR Rd AO Pi LISTA SPEAREF OUTPYES
TEDW AMET VW RMS
CALTON = ry
TE FRE VENT THE Feist OF FIRE AND SHON HAZARD, DO NOT (O) (O) © © ®
EXP - Cs sivas ÉD Must dé woe Toi DO
FERRE FROWN CASE MOIEER-EEAICEES E PARTE BEDE ay
LEE _
a as ou
REFER GERYEMG ToC a E PERA
AVES peor GE Ces PLE HELE - Ka PAS Caran
PEL ALE EFFECTS FOOT SWITCH
ALLE
à Caire
1 2 3 4 4 5 6 7 8
RETURN En
LINE CORD (120 V products only) (1)
For your safety, we have incorporated a 3-wire line (mains) cable with proper groundina facilities. It is not advisable to
remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding
facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exist when the unit is
operated with the proper grounded receptacles.
GROUND SWITCH (2)
Three position rocker-type switch which, in most applications, should be operated in its center or zero position. There may
be some situations when audible hum and/or noise will come from the loudspeaker, If this situation arises, position the
ground switch to either positive or negative (+ or -) or until the noise is minimized.
NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a qualified
service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS.
HUM BALANCE (3)
A control to minimize hum. To adjust, first make sure that nothing is plugged into the amp but the speaker cabinet. Turn
the unit on and set the Pre Gain, Pump and Post Gain controls at 7. While listening to the speaker closely, gradually
rotate the Hum Balance control using a screwdriver until hum is at a minimum. This procedure is required periodically.
Reset Hum Balance after tube change.
SPEAKER OUTPUTS (4)
Speaker output (1/4") jacks are provided for main and auxiliary. Main jack is 8 chm impedance and auxiliary jack is 4
ohms. When both jacks are engaged, amplifier impedance is 4 ohms.
PREAMP OUT (5)
The preamp output can be used to route the amplified signal to a mixing console, tape recorder, etc. Connect the preamp
output, using a shielded cable, to an input of the tape recorder, mixer, etc. This patch does not affect the operation of the
amplifier.
EFFECTS RETURN (6)
Input for returning signals from external effects or signal processing equipment.
EFFECTS SEND (7)
Qutput for supplying signals to external effects or signal processing equipment.
REMOTE FOOTSWITCH JACK (8)
Provided for the connection of the supplied remote footswitch. Footswitch is used to select the Ultra Gain, Crunch Gain, or
Normal Channels and Defeat Reverb.
BLOCK DIAGRAM
TEHE
TUBE
STAGE
LOW NID HIOH
SUN EFFECTS
BEND RETUAN
WT
REVERE
REYERA REYERN
ORIVE IT RETURN
CRUNCH!
ULTRA
FT. GW
REVERB
This black diagram shows signal flow within the unit. In order to thoroughly understand the unit's functions, please siudy the block diagram carefully.
TONE SETTINGS
BALANCE CLEAN GAIN
ADJUST TO TASTE WITH CRUNCH AND ULTRA ULTRA LEAD
MASTER FINES Ma" x CLEAN GAIN ER GAIN ULTRA GAIN INPUTS
a 56 4 6 а Зв a 3g a 2g 4 56
3 ; 3 ra 7 24 No x 3 7 NU 3 7 3 7 a 7
2 в Ге B 2 B 2 В ox À В BE a | 2 B 2 8 —+ ——
| q 1 a E © 1 a 4 9 g 1 ÿ 1 8 9 g
E iF о 10 о 410 o 10 @ 10
о 10 0 a : LOW HIGH
ВЕМЕЯВ PRESENCE HIGH Mali LOW GAIN POST PRE POST PRE GAIN GAIN
CLEAN AND LEAD CALNCH AMY TRIM
EQUALIZATION
NOTE:
ONLY HIGH AND PRESENCE EQUALIZATION ARE EFFECTIVE IN CRUNCH AND ULTRA CHANNELS.
Tone settings given are general and will vary according to type of guitar, type and gauges of strings, type of pickup and
even type of pick. Personal tasle, playing style and type of music greally contribute lo desired tonality.
SPECIFICATIONS
TRIUMPH 60 TRIUMPH 120
POWER AMPLIFIER SECTION: POWER AMPLIFIER SECTION:
2 - 6L6GC'5 with 12AXT driver 4- ELEGC's with 124X7 driver
RATED POWER £ LOAD: RATED POWER 4 LOAD:
60 W AMS into 8 or 4 ohms 120 W RMS into 8 or 4 ohms
POWER (3 CLIPPING: POWER @ CLIPPING:
(Typically @ 5% THD, 1 kHz, 120 Vac line) (Typleally @ 5% THD, 1 kHz, 120 Vac line)
65 W RMS into 8 or 4 ohms 130 W AMS into 8 or 4 ohms
{Bias must be reduced to measure) {Bias must be reduced to measure)
FREQUENCY RESPONSE: FREQUENCY RESPONSE:
+0, -2 dB 50 Hz to 20 kHz (9 50 Y RMS into 68 ohms +0, -2 de 50 Hz 10 20 kHz 2 100 W RMS into B ohms
HUM 6 NOISE: HUM £ NOISE:
Greater than 83 dB below rated power Greater than 83 dB below rated power
HUM BALANCE CONTROL: HUM BALANCE CONTROL:
Adjust for minimum hum & max gain Adjust for minimum hum & max gain
POWER CONSUMPTION: POWER CONSUMPTION:
200 Watts, 50/60 Hz, 120 Vac (Domestic) 400 Watts, 50/50 Hz, 170 Vac (Domestic)
PREAMP SECTION: PREAMP SECTION:
3 - 12АХ75, 1 - 12АТ7 3 - 12AX75, 1 - 12AT7
The following specs are measured @ 1 kHz with the Tha following specs are measured @ 1 kHz with the
controls preset as follows: controls preset as follows:
Low & High EQ @ 10, Mid EQ @ 0, Presence @ 0 Low & High EQ @ 10, Mid EQ 60, Presence @ 0
Ultra & Crunch Posts @ 10, Master Reverb @ 0 Ultra & Crunch Posts @ 10, Master Reverb @ 0
(Nominal levels are with Pre Gains (? 5) (Nominal levels are with Pre Gains @ 5)
(Minimum levels are with Pre Gains @ 10) (Minimum levels are with Pre Gains @ 10)
PREAMP HIGH GAIN INPUT: PREAMP HIGH GAIN INPUT:
Impedance: Very high Z, 470K ohm Impedance: Very high £, 470K ohm
ULTRA CHANNEL: (default channel) ULTRA CHANNEL: (default channel)
Nominal input Level: - 62 dBV, 0.5 mV RMS Nominal Input Level; - 62 dBY, 0.5 mV AMS
Minimum Input Level: - BO dBY, 0.1 mY AMS Minimum Input Level; - 80 de, 0.1 mY RMS
CAUNCH CHANNEL: (toolswiteh selected) CRUNCH CHANMEL: (footswitch selected)
Nominal Input Level: -62 dBY, 0.8 mV AMS Nominal Input Level; -62 dE Y, 0.B my RMS
Minimum Input Level: -74 dav, 0.2 mv AMS Minimum input Level: -74 dev, 0.2 my AMS
CLEAN CHANNEL: (footswitch selected) CLEAN CHANNEL: (footwitch selected)
: x Nominal Input Level: -20 dBY, 100 my AMS
Nominal Input Level: -20 dBY, 100 mv RMS Minimum Input Level: -42 dBV, 8 mV RMS
Minimum Input Level: -42 dBY, 8 mV AMS : Ea
Maximum Input Level: 0 dBY, 1.0 Y AMS
PREAMP LOW GAIN INPUT: {-6 dB Pad)
Impedance: High £, 44K ohms
All levels are increased by + 6 dB
Maximum Input Level: O dBY, 1.0 Y AMS
PREAMP LOW GAIN INPUT: (-6 dB Pad)
Impedance: High Z, 44K ohms
All levels are increased by + 6 dB
EFFECTS SEND:
EFFECTS SEND: |
Load Impedance: 47K ohms or greater Load impedance: 4715 aims of aa
Nominal Output: -20 d8V, 100 mV RMS diciones oa FORMS
EFFECTS RETURN: | EFFECTS RETUAN:
Impedance: Very high Z, 470K ohm Impedance: Very high Z, 470K ohm м
Designed Level: - 20 dBV, 100 mV RMS Designed Level: - 20 dBV, 100 mV RMS
PREAMP OUTPUT: PREAMP OUTPUT:
Load Impedance: 47K ohms or greater Lead Impedance: 47K ohms or greater
Nominal Output: +10 dBV, 3 V AMS Nari Quip: +18 SOV S 4 Hi
; "и REMOTE FOOTSWITCH:
REMOTE FOOTSWITCH: Special 3 button unit with LED indicators (supplied)
Sadia) 3 bution UniWIth LED Indra eee) SYSTEM HUM & NOISE @ NOMINAL LEVEL: (Clean channel
SYSTEM HUM 4 NOISE @ NOMINAL LEVEL: (Clean channel) 20 H 20 kHz unweighted) i
(20 Hz to 20 kHz unweighted) Les na EE
L Greater than 78 dB below rated power
Greater Ihan 75 de below rated power Cinacial ndi in circuitry for ultra & crunch)
(Special noise gain circuitry for ultra & crunch) ROPA Kin gai Cry
EQUALIZATION: em Les E & High passive type EQ for clean channe!
Custom Low, Mid & High passive type EC for ciean channel EURE 0 DOES YO NO
Special thick EQ actvated for ultra 8 crunch channels Special thick EG activated for ultra & crunch channels
PRESENCE: mu
+6 dB @ 5 kHz
+6 dB @ 5 kHz PUSH BRIGHT:
PUSH BRIGHT: |
+6 dB @ 2 kHz
+5 dB @ 2 kHz
THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO
WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY.
Ces clauses de garantie ne sont vaiables qu'aux Etats-Unis et au Canada. Dans tous les autres pays, les clauses de garantie et de maintenance sont fixees par le distributeur national et
assuree par lul seion la legislation en vigueur.
Diese Garantie ist nur in den USA and Kanada quitig. Alle Export-Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes unierworien.
Esta garantia es vallda solamente cuando el producto es comprado en E.U. continentales 0 en Canada. Todos los productos que sean comprados en el extranjero, estan sujetos alas
garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises.
ONE-YEAR LIMITED WARRANTY/REMEDY
PEAVEY ELECTRONICS CORPORATION (“PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material
and workmanship for a period of one (1) year from date of purchase, PROVIDED, however that this limited warranty is extended only to the original retail purchaser and is subject to the
conditions, exclusions and limitations hereinafter set forth:
PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS
If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90)
days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions and
limitations hereinafter set forth.
CONDITIONS, EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES
These limited warranties shall be void and of no effect if:
a. The first purchase of the product is for the purpose of resale; or
b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or
¢. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in material or
workmanship; or
d. The serial number affixed to the product is altered, defaced or removed.
In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will:
a. In the case of tubes or meters, replace the defective component without charge;
b. In other covered cases (i.e., cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace
the product, at Peavey's option;
and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser.
THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROM THE
DATE OF YOUR PURCHASE.
In order to obtain service under these warranties, you must:
a. Bring the defective item to any AUTHORIZED PEAVEY DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF
PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product.
If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or
AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.
OR
b. Ship the defective item, prepaid, to:
PEAVEY ELECTRONICS CORPORATION
International Service Center
Highway 80 East
MERIDIAN, MS 39301
including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return address. Upon
Peavey's receipt of these items:
If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the necessary
warranty service to repair or replace the product and will return it, FREIGHT COLLECT, to you, the purchaser,
Peavey's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual damages up to the
greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action. Such purchase
price will be that in effect for the specific product when the cause of action arose. This limitation of liability will not apply to claims for personal injury or damage to real property or
tangible personal property allegedly caused by Peavey’s negligence. Peavey does not assume liability for personal injury or property damage arising out of or caused by a non-Peavey
alteration or attachment, nor does Peavey assume any responsibility for damage to interconnected non-Peavey equipment that may result from the normal functioning and
maintenance of the Peavey equipment.
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES OR ANY CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF
THE EXPRESS. LIMITED WARRANTIES. AS HEREINABOVE STATED, HAVE BEEN COMPLIED WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE
APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THEEXCLUSION ORLIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU, THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
THESE LIMITED WARRANTIES ARE THE ONLY EXPRESS WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REFRESENTATION, WARRANTY OR
AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
In the event of any modification or disclaimer of express or implied warranties, or any limitation of remedies, contained herein conflicts with applicable law, then such modification,
disclaimer or limitation, as the case may be, shall be deemed to be modified to the extent necessary to comply with such law.
Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to
equipment purchased in the United States of America.
INSTRUCTIONS — WARRANTY REGISTRATION CARD
1. Mail the completed WARRANTY REGISTRATION CARD to:
PEAVEY ELECTRONICS CORPORATION
POST OFFICE BOX 2898
MERIDIAN, MISSISSIPPI 39302-2898
a. Keep the PROOF OF PURCHASE. In the event warranty service is required during the warranty period, you will need this document. There will be no identification card
issued by Peavey Electronics Corporation.
2. IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESS:
a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may require correction, the REGISTRATION
CARD will help ensure that you are contacted and properly notified.
b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to
facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of
information or correction.
3, You may contact Feavey directly by telephoning (601) 483-5365.
4. Please have the Peavey product name and serial number available when communicating with Peavey Customer Service.
DANGER
EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE A PERMANENT HEARING LOSS INDIVIDUALS VARY CONSIDERABLY IN SUSCEPTIBILITY TO NOISE INDUCED HEARING LOSS, BUT NEARLY
EVERYONE WILL LOSE SOME HEA4AING IF EXPOSED TO SUFFICIENTLY INTENSE NOISE FOR A SUFFICIENT TIME
THE 1.5 GOVERMMENT'S OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION {OSHA} HAS SPECIFIED THE FOLLOWING PERMISSIBLE NOISE LEVEL EXPOSURES:
SOUND LEVEL daa, SLOW RESPONBE
BO
La
a fe
oh
ud
DURATION PER DAY IN HOURS
FIER HAS BEEN DESIGNED
AL PEAK POWER, ADEQUAT
D DAMAGE THE AS SUCIATS
for pis reference.
Obey all cautions in the operating instructions and on the
back of the uni,
All operating instructions should ba followed.
This product should not be used near water, Le à
bathtub, sink, swimming pool, wet basement, atc,
. This product should be located so that its position does
not interfere with its proper ventilation. 11 should not be
placed flat against a wall or placed in a built-in enclosure
that will impede the Now of cooling air.
Thig product should not be placed near a source of neat
such as a stove, radiator or another heal producing
amplifier
power supply Gi
roundin
Far
booklet ‘Shock Hazard and Grounding.”
. Power supply cords should always be handled carefully
Mever walk or place equipment on power supply cords.
Periodically check cords for cuts or signs of stress,
especially al the plug and the point where the cord axils
the unit
- The power supply cord should be UnpRiaded whan the
unit is to be unused for long periods of tim
this product isto be mounted in an equip vr rack, raar
support should be provided.
write for our frae
14.
Care should be taken so thal objects do not fall and
liquids are not spilled into tha unit rough the ventilation
or any ofher openings.
This unit should be checked by a qualified service
technician if.
Á. The power supply cord or plug has been damaged
E. Anything has fallen or been spilled into the unit.
C. The unit doës not operate correctly,
D. Theunil hasbeen dropped or tha enclosure damaged.
The usar should not to attempt to service this equipment
All service work should be done by a qualified service
technician,
ANG
Features and specifications are subject to change without notice.
©1987
PEAVEY ELECTRONICS CORPORATION/711 À Street/Meridian, MS 39301/Phone: (601) 483-5365/Fax (601) 484-4278/Telex. 504115
Printed in U.S.A. 11/87
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021