OleXL Installation Manual

Extra Large OLED

Olé

™

XL

PATENT PENDING

Film Interactive Touchpad

Installation Manual

E L A N H O M E S Y S T E M S INSTALLATION MANUAL

Olé™XL

Contents

1. Introduction

................................................................ 3

Film Interactive Technology ........................................... 3

Features ............................................................................. 4

Installation & Usage Tips ................................................ 5

Cleaning The Touch Screen ........................................... 6

Specifications .................................................................... 7

Olé2XL-Front .................................................................... 8

Olé2XL-Rear ...................................................................... 9

Films .................................................................................... 10

2. System Design, Installation and

Connections

..................................................................... 11

Planning .............................................................................. 11

Installation ......................................................................... 11

Pre-Wire .............................................................................. 11

Rough

-

In ............................................................................. 12

Mounting Height ............................................................... 12

Changing Films ................................................................. 13

Connectors/Pinout ........................................................... 14

RJ-45 Connector .............................................................. 14

LOCAL IR Interface Port .................................................. 15

IR-EMITTER OUT .......................................................... 15

IR-RECEIVER IN ............................................................ 16

LOCAL SENSE IN ......................................................... 17

System Connections ........................................................ 18

Stand-Alone/Home Theater ......................................... 18

Stand-Alone/Home Theater - Expanded ..................... 19

ELAN S12/S6 - Z•NET MODE

(w/ SPP)

......................... 20

ELAN S12/S6 - Z•NET MODE

(No SPP)

......................... 20

ELAN S12/S8/S6 - VIA!NET MODE

(w/ SPP)

................. 21

ELAN System6-VIA!NET MODE

(w/ PVIA4/PVIA10)

.......... 22

ELAN Z• System-Z•NET

(w/PZ6-3 or Fewer Touchpads)

.... 23

© 2007 ELAN Home Systems • All Rights Reserved

Page 1

Olé2XL

INSTALLATION MANUAL E L A N H O M E S Y S T E M S

ELAN Z

•

System-Z•NET

(Four or More Touchpads)

........... 23

ELAN Z

•

System-Z•NET

(No PZ6-3 or Fewer Touchpads)

... 24

ELAN Z• System-VIA!NET

(w/ PZ6)

............................... 25

ELAN Z• System-VIA!NET

(No PZ6)

............................... 26

3. Programming

.............................................................. 27

To Download a VIA!TOOLS Project: ............................... 27

Feature Enable/Disable ................................................... 28

Speaker ............................................................................ 28

IR Sensor ......................................................................... 28

Light Sensor Enable/Disable ........................................... 28

4. Troubleshooting

........................................................ 29

Limited Warranty

............................................Back Page

Page 2



Olé2XL

1. Introduction

Olé™2XL

(patent pending)

Film Interactive Touchpad (FIT) is a double-gang, in-wall system controller that uses a touch Film in lieu of hard buttons to perform all functions normally associated with a keypad. Source and system control icons and function names are printed on interchangeable backlit film transparencies. Each icon or function name corresponds to an active “hot spot” that issues a control command and gives both audible and visual confirmation to the user when pressed.

Multiple IR commands, or ‘Sequences’, can be issued from a single press of any button on any template. The touchpad features a 4-line, 2" color

OLED to provide source, system and programming feedback to the user.

Programming is accomplished with ELAN’s VIA!TOOLS Setup Software and is done through a direct link from a computer to the mini-USB Download Port on the front of the unit.

Olé2XL is designed to use easily installed films that are available in a wide variety of configurations in various graphical themes to match any room’s decór.

Film Interactive Technology

Olé2XL utilizes a polyester plastic film suspended over a glass panel, which is placed over a changeable backlit film. Depressing the polyester film with a finger allows the film to touch the glass panel underneath, generating a location signal that is read by the electronics. Each button location (or “hot spot”) is assigned an IR or RS-232 command that controls sources such as

A/V equipment, HVAC systems, drapes, shades, lighting systems, or even fireplaces! Each touchpad is custom-programmed to perform exactly the functions required for each individual home, room, and/or system.


Page 3

Olé2XL


Features

• Full touchpad design, no hard buttons

• Interchangeable control templates

• 2” color OLED (Organic LED)

• Brightness-adjusting light sensor

• Audible ‘click’ to indicate a button press (can be

disabled in software)

• Enhanced VIA!TOOLS programming

• Compatible with all current ELAN multi-room controllers

• Stand-alone use in any IR-based system

• Z•NET/VIA!NET compatibility

• Two-way RS-232 feedback capability

• Built-in IR receiver

• Connectivity for Local IR Output and Remote IR Receiver

• System Sense sequence capability

• Fits in a double-gang electrical box

• Virtually unlimited IR command sequences issued

from any button press

• Multiple wall plate options for enhanced décor-matching

• Patent Pending

Page 4



Olé2XL

Installation & Usage Tips

• When properly installed, nothing should be applying contact pressure

to the touchpad except for the operator’s finger. If something is touch-

ing the touchscreen window a false signal can be generated, causing

the touchpad not to respond a finger press (ELAN does not recom-

mend wrapping the removable frame with wallpaper as this can cause

the aforementioned symptom). Too much force on the front of the

touchpad, or concentrated pressure, can damage the polyester film or

break the underlying glass plate.

• Avoid installation in direct sunlight or strong ultraviolet light (such as

grow lamps, plant lights, or compact flourescent lights). This can

degrade and discolor the polyester film.

• Avoid installation over heat generating devices and/or in moist areas

where condensate can form on the polyester film. Both heat and con-

densed moisture can affect touch screen performance.

• Avoid installation next to thermostats. The touch screen generates

heat that can effect thermostat control and readings.

• Avoid applying any foreign objects, such as adhesive labels, on the

touchscreens polyester film. This can release chemicals that can dis-

color the clear film.

• The touchpad should not be mounted near electronics that emit radio

frequencies or electromagnetic interference (such as the deflection

circuits of CRT monitors, light dimmers, and some power supplies)

• The edge of the touchpad has exposed sharp glass. Be careful when

handling the assembly in order to avoid injury.


Page 5

Olé2XL


Cleaning The Touch Screen

To clean the polyester film, first use a soft dry cloth to remove contamination. If dust or smudges are still present, use a damp cloth that has been squeezed of excess water to remove the contaminant. If contaminants are still present, use a non-abrasive cleaner or detergent to clean the polyester film. Use of strong chemicals and/or some cleaning agents may discolor the polyester film. The following cleansers have been tested and approved for cleaning an Olé2XL Touchpad:

• Windex

®

Glass Cleaner

• Formula 409

®

Cleaner

• Mr. Clean

®

The following substances have also been tested and shown to have no adverse effects to the touchpad’s polyester film:

• Coffee

• Tea

• Ketchup

• Mustard

• Tomato Juice

• Lemon Juice

• Hand Lotion

• Parafﬁ n based grease

• Ammonia

• Carbureter cleaner

• Ethanol

• Acetone

• Hydro-seal

®

• Nitric Acid <10%

• Bleach

• 10W40 motor oil

• Turpentine

• Brake Fluid

• Wisk

®

• Toluene

• Hydrochloric Acid <10%

• Methyl ethyl ketone

• Ethyl acetate

• Cyclohexanone

• Diesel oil

• Lube grease

• Copper based grease

• Xylene Dimethyformamide

• 1.1.1 Trichlorethane Diethyl ether

• Sodium hydroxide <10%

Page 6



Olé2XL

Specifications

Viewing Angle

.......................... 180° up/down,180° left/right

Operating Temp.

..................... 32°F-104°F / 0°C-40°C

OLED Display

........................... Type: 2” Organic LED (OLED)

Colors: 252K

Resolution: 160 pixels (W) x 128 pixels (H)

Connections

............................. System Port: RJ-45

Interface Port: 5-position screw terminal

Download Port: Mini USB

Wiring Requirements

............ Cat-5

Power Requirements

............. 12VDC/150mA or 16VDC/150mA

Dimensions

(w/ Wall Plate) ..... ( i n . ) 4 5/8(W) x 4.5/8(H) x 1 3/16(D)

(mm) 117(W) x 117(H) x 30(D)

Dimensions

(w/o Wall Plate) .... ( i n . ) 4 7/16(W) x 4 7/16(H) x 1 1/8(D)

(mm)112(W) x 112(H) x 26(D)

Fits in 32 cu in. double-gang electrical box

Weight

........................................ 14 oz./0.4kg

Shipping Weight

..................... 16 oz./0.45kg

Power Consumption/Maximum Load per ELAN

Multi-Room Controller

Each Olé2XL Touchpad draws 150mA in either 12V or 16V mode. Use the table below to determine the maximum number of touchpads that can be used per ELAN Multi-Room System Controller.

S6

# of

Olé2s Per

Zone

# of

Olé2s Per

S6

S8

# of

Olé2s Per

Zone

# of

Olé2s Per

S8

S12

# of

Olé2s Per

Zone

# of

Olé2s Per

S12

Z•630

# of

Olé2s Per

Zone

# of

Olé2s Per

Z•630

1 6 2 16

2

16 1 3

Note: See System Connections for specific recommendations when an application requires that the above Maximum loads be exceeded.


Page 7

Olé2XL


Olé2XL-Front

1 1

2

2

1

1

1

1

Mounting Screw (x 4)

4

Program Button

(future use)

2

Film Hinge (x 2)

5

Light Sensor

3

Film Screw (x 2)

6

Mini USB Download Port

Page 8


3

6

5

4

3


Olé2XL

Olé2XL-Rear

1 2 3 4 5 6 7 8

1

2 3

1

Z•NET/VIA!NET Switch

2

System RJ-45 Jack

3

Interface Port


Page 9

Olé2XL


Films

Olé2XL utilizes different films in various styles in order to match a wide variety of decors. A few examples are shown below.

Olé2XL Film “Beaches”

Olé2XL Film “Mountains”

Olé2XL Film “Southwest”

Page 10



Olé2XL

2. System Design, Installation and

Connections

Planning

Before installing the Olé2XL, it is essential to have a detailed and accurate system design. Talk with the homeowner to make sure all expectations and design goals are explored. The first step to a good design is to map the system. It is advisable to mark up a copy of the house floor plan with speaker, keypad, touch panel, volume control, and equipment locations etc. Make sure that all locations are decided upon before pre-wiring commences so that all necessary wiring and installation hardware is in place.

It is essential that ALL system components are accounted for prior to the pre-wire stage. After establishing design goals with the homeowner, make a detailed list of all components. Include source equipment, keypads, touch panels, volume controls, amplifiers, communications gear, etc. Gather up any IR remote controls that may be necessary for final programming, or ensure that the IR codes for all equipment to be installed are available in the

VIA!TOOLS IR Library.

Installation

Olé2XL is designed to fit into a standard 32 cu. in. two-gang electrical box.

Consult local building codes for specifics in your geographic area.

Pre-Wire

Olé2XL requires power, control, and status to function correctly. Each

Touchpad has an RJ45 jack on the back to allow for easy connection. Run

Cat-5 wire from the main central equipment location (head-end) to the location where each Touchpad will be installed.

ELAN recommends the use of C45P RJ-45-to-pigtail interface cables when installing Touchpads. The RJ-45 pinout for each ELAN multi-room controller is included in the manual for that particular product.

Note: Use of wire other than Cat-5 may produce undesired results

(IR bandwidth may be narrowed or interference may occur).

Note: Maximum wire run is 500 feet.


Page 11

Olé2XL


Rough-In

Roughing-in the Olé2XL requires careful attention to the design plan made previously. See System Design & Applications for a list of things to factor in to specific mounting locations before deciding exactly where to place the unit. In order to avoid Electro-Magnetic Interference (EMI), do not mount

Touchpads close to light dimmers. Leave at least one stud-bay open between Touchpads and dimmers (leave more space if multiple dimmers are present). Avoid installing Olé™XL Touchpads in areas that will receive direct sunlight. Sunlight can flood the IR receiver and make the system inoperative.

Do not mount Touchpads outdoors! Corrosion will damage them. ELAN does not warrant Olé Touchpads for outdoor use.

Mounting Height

Olé2XL has no viewing angle limitations, so mounting height should be determined by the average height of the user. Typical mounting height is

56-60 inches from the floor to the bottom of the frame. This will provide optimum viewing for the largest number of people.

Page 12



Olé2XL

Changing Films

To change films:

1. Remove the magnetic wall plate from the front of the unit.

2. Remove the two film screws on the right side of the unit.

3. Use the notch located in the upper right-hand corner to open the

touch screen (45° max.).

4. Remove the existing film.

5. Place the new film into the holder of the transparent touch

screen making sure of the proper orientation.

6. Close the touch screen.

7. Replace the two film screws.

8. Replace the wall plate.

Screw

Screw

Film

Touch

Screen

Place Film in Holder on

Touch Screen


Page 13

Olé2XL


Connectors/Pinout

Olé2XL has a System RJ-45 connector and a five pin Interface Port connector which each perform specific functions. All applications will use the RJ-45 connector, while certain situations will require the use of the Local/AUX connector.

RJ-45 Connector

The System RJ-45 provides required functionality for all system types. Use this connector when the Olé2XL is used in an ELAN Multi-Room Controllerbased system (ELAN S or Z• System). This connector must also be used in Stand-Alone systems and systems with Local applications. Use ELAN

Standard Pinout configuration.

S6/S12 and

Z•Systems:

Use ZNET when NOT using a

VIA!-SC4 or SS1

All ELAN

Systems:

Use VIA!NET

when using a

VIA!-SC4 or SS1

S8 Systems:

Always Use

VIA!NET

Insert wires in this order:

Blue

White/Blue

Orange

White/Orange

Green

White Green

Brown

White/Brown

ELAN ZNET RJ-45 Pin-Out

PIN # COLOR CODE

TAB

TAB

CABLE

BLUE N/C

WHITE/BLUE IR OUT

ORANGE Local IR

WHITE/ORANGE RS-485+

GREEN RS-485-

WHITE/GREEN 12VDC+

BROWN GND

WHITE/BROWN N/C

ELAN VIA!NET RJ-45 Pin-Out

PIN # COLOR CODE

CABLE

7

8

5

6

3

4

1

2

6

7

8

3

4

1

2

5

OléXL

RJ-45 Connector

BLUE Sense

WHITE/BLUE IR OUT

ORANGE RS-485-

WHITE/ORANGE RS-485+

GREEN GND

WHITE/GREEN 16VDC+

BROWN GND

WHITE/BROWN 16VDC+

Page 14



Olé2XL

LOCAL IR Interface Port

Use this connector when utilizing the Olé2XL’s Local Control features such as Local source control, Local IR Sensors, or Sense-enabled automated sequences.

IR-EMITTER OUT

The Local IR-EMITTER OUT is typically used to control a device that is not part of the main IR system, such as a TV or DVD player located within the same room as the touchpad or an ELAN Electronic Volume Control such as a VSE100. IR is routed to an emitter or IR distribution block connected to the

Local IR Output in two ways:

1. Any IR signal that is received from the Local IR-RECEIVER IN is sent

out both the Local IR-EMITTER OUT and the System IR Output.

2. IR signals may be specified in programming as “Local” and be routed

through the Local IR-EMITTER OUT. See VIA!TOOLS “Help” file for

specific information about IR routing.

Connect IR-EMITTER OUT and -GROUND as shown below.

Olé2XL

Interface Port

IR Emitter

Olé2XL

Interface Port

IR + = White Stripe

GND = Black

IR Emitters

The Connection Labeled

"+12 VOLTS OUT" is A

Voltage OUTPUT.

DO NOT CONNECT

A POWER SUPPLY

TO THIS CONNECTION!

IR OUT

+12V

GND

ST OUT

IR IN

LP/HP IR OUT

IR

RCVR

STATUS IN

5~24V D C

12V DC

REGULATED

IRD4

Amplified IR

Distribution Block


Page 15

Olé2XL


IR-RECEIVER IN

The Local IR-RECEIVER IN is typically used to connect an external IR sensor to the touchpad. Typical applications include a plasma-friendly IR sensor (ELAN IRS8EP, for example) placed near a TV, or an auxilliary IR sensor placed in an area more convenient than the location of the touchpad. IR signals that are received by the IR Input are sent out both the Local IR-EMITTER

OUT and the System IR Output.

Connect IR-RECEIVER IN, -GROUND and +12VOLTS OUT as shown below.

Note: In certain cases, the built-in IR sensor on the Olé2XL can be flooded with plasma TV interference or other ambient light interference In this case, connect a plasma-friendly IR sensor (ELAN

IRS8EP, for example) to the Local IR Input and disable the built-in IR sensor in VIA!TOOLS.

Olé2XL Interface Port

IR

G

+12VDC

IRS8EP

Extreme Plasma

IR Sensor

Page 16



Olé2XL

LOCAL SENSE IN

The LOCAL SENSE IN port allows a contact-closure to trigger IR or RS-232 sequences programmed in VIA!TOOLS. Use a motion sensor to activate a contact-closure and cause automated actions such as system power on, drapes closed, and lights dimmed, for example.

Connect LOCAL SENSE IN and -GROUND to a contact-closure device as shown below.

Olé2XL Interface Port

Contact-Closure

Device


Page 17

Olé2XL


System Connections

Stand-Alone/Home Theater

Olé2XL is ideal for use as a stand-alone (non-ELAN) system controller or

Home Theater controller. For control of a Home Theater system, the Olé2XL is combined with a method for IR distribution such as ELAN’s IRD4 Amplified

IR Distribution Block. Signals originate at the Olé2XL and travel to the distribution block where they are routed to each component. In this application, power the Olé2XL from the IRD4’s included power supply, as shown. Place the Z•NET/VIA!NET Switch in the “Z•NET” position (to the left).

Stand-Alone IRD4 to Olé2XL Connections

Sources

Olé2XL

ELAN

C45P

White/Brown

Brown

White/Green

N/C

Green

White/Orange

Orange

N/C

N/C

N/C

White/Blue

Blue N/C

IRD4 Amplified IR

Distribution Block

Note: The PWR2 12VDC 200mA Power Supply included with the

IRD4 is capable of supporting one Olé2XL Touchpad. If additional touchpads will be installed, the ELAN PWR3 +12VDC 2.1A power supply should be used. The PWR3 will support up to thirteen

Olé2XL Touchpads. If more than two touchpads will be connected to the IRD4, use jumper wires to connect the additional units prior to the connector locations on the IRD4.

Page 18



Olé2XL

Stand-Alone/Home Theater - Expanded

Stand-alone systems (without an ELAN multi-room controller) can be as simple as one Olé2XL controlling one IR source, or as complex as multiple

Olé2XLs, VIA! Touch Panels, keypads, and IR sensors all controlling many

IR sources. The diagram below shows an Olé2XL and a VIA! Touch Panel controlling a stack of A/V gear. Use an ELAN PVIA4 Precision Panel to interconnect all of the controllers. Place the Z•NET/VIA!NET Switch in the

“VIA!NET” position (to the right).

Note: The PWR4 16VDC 4.3A Power Supply included with the PVIA4 is capable of supporting up to 24 Olé2XL Touchpads in Stand-Alone

Mode, however, each punchdown location will only support one wire. If more than 4 touchpads will be connected to the PVIA4, use jumper wires to connect the additional units prior to the punchdown locations on the PVIA4.

Stand-Alone PVIA4 to Olé2XL & VIA! Connections

VIA!

Olé2XL

ELAN

C45P

ELAN

C45P

Wh/Brown - +16V

Brown - GND

Wh/Green - +16V

Green - GND

Wh/Orange - N/C

Orange - N/C

Wh/Blue - IR OUT

Blue - N/C

G

485+

485-

IR

ST

V+

G

V+

VIA2

Wh/Brown - +16V

Brown - GND

Wh/Green - +16V

Green - GND

Wh/Orange - N/C

Orange - N/C

Wh/Blue - IR OUT

Blue - N/C

G

485+

485-

IR

ST

V+

G

V+

VIA1

XLINK

ST1

ST2

ST3

ST4

-

Z485

SIR

GND

1

Z-BUS

INT

2 EXT

PVIA4 Rear

IR

1

G

IR

2

G

3

G

4

G

V+

G

V+

G

485+

485-

IR

ST

VIA1

V+

G

V+

G

485+

485-

IR

ST

VIA2

V+

G

V+

G

485+

485-

IR

ST

VIA3

V+

G

V+

G

485+

485-

IR

ST

VIA4

-

4

+

-

1

+

-

2

+

-

3

+

PWR

GROUND

CONN

Stand-Alone IRD4 to PVIA4 to Olé2XL & VIA! Connections

Sources

VIA! Touch Panel Olé2XL

Cat-5 Cat-5

PVIA-4

1

1

9 VDC

INPUTS

2

3 4

1

3

ALL

2

4

TO SC-4

2

VIDEO

IN

3 4

3.5mm

Mini-Plug

PVIA4 Front

IRD4 Amplified IR

Connection Block


Page 19

Olé2XL


ELAN S12/S6 - Z•NET MODE (w/ SPP)

ELAN’s SPP Precision Panel for the S Series Multi-Room Controllers (S12, S8 and S6) makes quick work out of configuring Olé2XLs to control zones. Using

Cat-5, connect IR, RS485+/-, GND, and +12VDC as shown below. Place the

Z•NET/VIA!NET Switch in the “Z•NET” position (to the left). When used in

Z•NET mode, Olé2XLs are considered “keypads” for connectivity purposes in the S12/S8/S6 Installation Manuals. Please consult the S12/S8/S6 Installation

Manuals for additional details.

SPP To Olé2XL Connections

SN

IR

V485-

V485+

GND

+12V

GND

+12V

SPP Precision Panel

Zone 1C

12V Olé/ZPAD Connector

Blue

White/Blue

Orange

White/Orange

Green

White/Green

Brown

White/Brown

Cat-5

Butt splice or equivalent

Blue

White/Blue

Orange

White/Orange

Green

White/Green

Brown

White/Brown

Blue (N/C)

White/Blue (IR)

Orange (485-)

White/Orange (485+)

Green (N/C)

White/Green (+12V)

Brown (GND)

White/Brown (N/C)

Olé2XL

ELAN

C45P

Note: It is possible to use a PS12 Precision Panel for System12 applications, however, the SPP Precision Panel is designed for ALL

S Series applications and will be shown throughout this manual.

ELAN S12/S6 - Z•NET MODE (No SPP)

The diagram below shows the necessary connections for wiring an Olé2XL to a System12 or System6 Multi-Room Controller (in Z•NET mode) when NOT using an SPP Precision Panel. Using Cat-5, connect IR, RS485+/-, GND, and

+12VDC as shown below. Place the Z•NET/VIA!NET Switch in the “Z•NET” position (to the left).

S12/S6 to Olé2XL Z•NET Connections (No SPP)

S12/S6

ZONE

KEYPAD

INPUT

ELAN

C45P


Blue

White/Blue

Orange

White/Orange

Green

White/Green

Brown

White/Brown

Blue

White/Blue (IR)

Orange

White/Orange (485+)

Green (485-)

White/Green (+12V)

Brown (GND)

White/Brown

Standard ELAN RJ-45 Pin-Out

PIN # COLOR CODE

TA B

1

6

7

8

4

5

2

3

BLUE

WHITE/BLUE

ORANGE

WHITE/ORANGE

GREEN

WHITE/GREEN

BROWN

WHITE/BROWN

Olé2XL

ELAN

C45P

Page 20



Olé2XL

ELAN S6/S8/S12 - VIA!NET MODE (w/ SPP)

The VIA!NET configuration allows Olé2XL to provide RS-232 control for certain devices when used in conjunction with a VIA!-SC4 System Controller or

SS1 System Station. Use of an SPP Precision Panel in any S Series application that includes a VIA!-SC4 or SS1 is required. Using Cat-5, connect IR,

RS485+/-, GND, and +16VDC as shown below. Place the Z•NET/VIA!NET

Switch in the “VIA!NET” position (to the right). When used in VIA!NET mode,

Olé2XLs are considered “VIA!s” for connectivity purposes in the S6/S8/S12

Installation Manuals. Please consult the appropriate installation manuals for additional details. Please consult VIA!TOOLS “Help” file for specific information about two-way feedback and RS-232 controlled devices.

Note: Use of the SPP Precision Panel is required in any S12/S8 application that includes a VIA!-SC4 or SS1 System Station.

SPP to Olé2XL VIA!NET Connections

SPP Precision Panel

Z1B 16V/12V VIA!/OLÉ

N/C

IR

485-

485+

12V

G

16V

G

16V

16V

Blue

White/Blue

Orange

White/Orange

Green

White/Green

Brown

White/Brown

Cat-5

Blue

White/Blue

Orange

White/Orange

Green

White/Green

Brown

White/Brown


Blue

White/Blue (IR)

Orange (485-)

White/Orange (485+)

Green (GND)

White/Green (+16V)

Brown (GND)

White/Brown (+16V)

Olé2XL

ELAN

C45P


Page 21

Olé2XL


ELAN System6-VIA!NET MODE (w/ PVIA4/PVIA10)

The VIA!NET configuration allows Olé2XL to provide RS-232 control for certain devices when used in conjunction with a VIA!-SC4 System Controller or

SS1 System Station. Use of an ELAN SPP, PVIA4 or PVIA10 Precision Panel is required for this application. The drawing below shows a PVIA4 being utilized, PVIA10 connections are identical. Connect IR OUT, V485+/-, GND, and 16VDC from the Olé2XL to the PVIA4/PVIA10 as shown. Connect Z485+/-

, IR, and Ground from the PVIA4 to the S6. Place the Z•NET/VIA!NET Switch on the Olé2XL in the “VIA!NET” position (to the right). Place the Z-BUS jumper on the PVIA4 or PVIA10 to the INT (top) position as shown. Please consult the S6 Installation Manual for additional details. Please consult VIA!TOOLS

“Help” file for specific information about RS-232 controlled devices.

S6 to PVIA4 to Olé2XL VIA!NET Connections

Blue - N/C

Wh/Blue - IR IN

Orange - N/C

Wh/Orange - RS-485+

Green - RS-485-

Wh/Green - N/C

Brown - GND

Wh/Brown - N/C

ELAN

C4545

XLINK

ST1

ST2

ST3

ST4

-

SIR

GND

1

Z-BUS

INT

2 EXT

PVIA4 Rear

IR

IR

1

G

2

G

IR

3

G

4

G

G

485+

485-

IR

ST

V+

G

V+

VIA1

V+

G

V+

G

485+

485-

IR

ST

VIA2

G

485+

485-

V+

G

V+

IR

ST

VIA3

V+

G

V+

G

485+

485-

3

-

+

1

-

+

2

-

+

IR

ST

VIA4

4

-

+

PWR

GROUND

CONN

Olé2XL

ELAN

C45P

Wh/Brown - +16V

Brown - GND

Wh/Green - +16V

Green - GND

Wh/Orange - V485+

Orange - V485-

Wh/Blue - IR OUT

Blue - N/C

G

485+

485-

IR

ST

V+

G

V+

VIA1

S6

ZONE KEYPAD

INPUT

Page 22



Olé2XL

ELAN Z• System-Z•NET (w/PZ6-Three or Fewer Touchpads)

Use a PZ6 Precision Panel for Z• System when installing Olé2XLs in a

Z• system. Connect IR, RS485+/-, GND, and 12VDC from the PZ6 Precision

Panel to the Olé2XL as shown. Place the Z•NET/VIA!NET Switch in the

“Z•NET” position (to the left). Olé2XLs are considered “keypads” for connectivity purposes in the Z•630 Installation Manual. Please consult the Z•630

Installation Manual for additional details.

PZ6 to Olé2XL Z•NET Connections

PZ6 ZONE

Punchdown

Connector

Olé2XL

ELAN

C45P

Wh/Brown - N/C

Brown - GND

Wh/Green - +12VDC

Green - RS-485-

Wh/Orange - RS-485+

Orange - N/C

Wh/Blue - IR IN

Blue - N/C

ELAN Z

•

System-Z•NET (Four or More Touchpads)

When installing more than two touchpads in a Z• system, a PZ6 Precision

Panel and an ELAN PWR12 external power supply are required in order to provide sufﬁ cient power. Connect IR, RS485+/-, GND, and 12VDC from the PZ6 Precision Panel to the Olé2XL as shown above. Place the Z•NET/

VIA!NET Switch in the “ZNET” position (to the left). Plug an ELAN PWR12 power supply into the jack labelled “Z•025” on the front of the PZ6 Precision

Panel. This will disable the internal +12VDC power from the Z•630 and allow up to fourteen Olé2XL Touchpads to be installed per PZ6. Please consult the

Z•630 Installation Manual for additional details.

PZ6 Power Connection

PZ6 Front

PWR12

+12 VDC

2.1A

Note: The PWR12 has reversed polarity compared to other power supplies and MUST be utilized in this application. Other +12VDC power supplies will not work!


Page 23

Olé2XL


ELAN Z

•

System-Z•NET (No PZ6-Three or Fewer Touchpads)

When installing Olé2XLs in a Z• system and NOT using a PZ6 Precision

Panel, connect IR, RS485+/-, GND, and 12VDC from the Z•630 to the Olé2XL as shown. Place the Z•NET/VIA!NET Switch in the “Z•NET” position (to the left). Olé2XLs are considered “keypads” for connectivity purposes in the

Z•630 Installation Manual. Please consult the Z•630 Installation Manual for additional details.

Z•630 to Olé2XL Z•NET Connections

ELAN

C45P

BLUE

WHITE/BLUE

ORANGE

WHITE/ORANGE

GREEN

WHITE/GREEN

BROWN

WHITE/BROWN

BLUE

WHITE/BLUE

ORANGE

WHITE/ORANGE

GREEN

WHITE/GREEN

BROWN

WHITE/BROWN

ZONE 1

Olé2XL

ELAN

C45P

BLUE

WHITE/BLUE

ORANGE

WHITE/ORANGE

GREEN

WHITE/GREEN

BROWN

WHITE/BROWN

ZONE 2

Olé2XL

ELAN

C45P

BLUE

WHITE/BLUE

ORANGE

WHITE/ORANGE

GREEN

WHITE/GREEN

BROWN

WHITE/BROWN

ZONE 3

Olé2XL

ELAN

C45P

Note: The Z•630 will support a maximum of three Olé Touchpads using internal 12VDC power. A PZ6 Precision Panel and an ELAN

PWR12 external power supply must be used when more than three touchpads are being installed. See ELAN Z• System Z•NET (Four or

More Touchpads) for proper connectivity.

Page 24



Olé2XL

ELAN Z• System-VIA!NET (w/ PZ6)

ELAN recommends the use of a PZ6 Z•System Precision Panel when installing Olé2XLs in a Z•System. A PVIA4 or PVIA10 Precision Panel is required when Olé Touchpads are being used in conjunction with a VIA!-SC4 or SS1

System Station. The drawing below shows a PVIA4 being utilized; PVIA10 connections are identical. Connect IR OUT, V485+/-, GND, and 16VDC from the Olé2XL to the PVIA4/PVIA10 as shown. Connect Z485+/-, IR, and Ground from the PVIA4 to the PZ6. Place the Z•NET/VIA!NET Switch on the Olé2XL in the “VIA!NET” position (to the right). Place the Z-BUS jumper on the PVIA4 or PVIA10 to the INT (top) position as shown. Please consult the Z•630

Installation Manual for additional details.

PZ6 to PVIA4 to Olé2XL VIA!NET Connections

PZ6 ZONE

Punchdown

Connector

Cat-5

Wh/Brown - N/C

Brown - GND

Wh/Green - N/C

Green - RS-485-

Wh/Orange - RS-485+

Orange - N/C

Wh/Blue - IR IN

Blue - N/C

XLINK

ST1

ST2

ST3

ST4

-

SIR

GND

1

Z-BUS

INT

2 EXT

PVIA4 Rear

IR

IR

4

G

IR

3

G

IR

2

G

IR

1

G

V+

G

V+

G

485+

485-

IR

ST

VIA1

485+

485-

IR

ST

V+

G

V+

G

VIA2

485+

485-

IR

ST

V+

G

V+

G

VIA3

V+

G

V+

G

485+

485-

IR

ST

VIA4

4

-

+

3

-

+

2

-

+

1

-

+

PWR

GROUND

CONN

Olé2XL

ELAN

C45P

Wh/Brown - +16V

Brown - GND

Wh/Green - +16V

Green - GND

Wh/Orange - V485+

Orange - V485-

Wh/Blue - IR OUT

Blue - N/C

485+

485-

IR

ST

V+

G

V+

G

VIA1


Page 25

Olé2XL


ELAN Z• System-VIA!NET (No PZ6)

A PVIA4 or PVIA10 Precision Panel is required when Olé Touchpads are being used in conjunction with a VIA!-SC4 or SS1 System Station. The drawing below shows a PVIA4 being utilized; PVIA10 connections are identical.

Connect IR OUT, V485+/-, GND, and 16VDC from the Olé2XL to the PVIA4/

PVIA10 as shown. Connect Z485+/-, IR, and Ground from the PVIA4 to the

Z•630.Place the Z•NET/VIA!NET Switch on the Olé2XL in the “VIA!NET” position (to the right). Place the Z-BUS jumper on the PVIA4 or PVIA10 to the

INT (top) position as shown. Please consult the Z•630 Installation Manual for additional details.

Z•630 to PVIA4 to Olé2XL VIA!NET Connections

Zone 1 Connections Shown

Wh/Brown - N/C

Brown - GND

Wh/Green - N/C

Green - RS-485-

Wh/Orange - RS-485+

Orange - Zone 3 IR IN

Wh/Blue - Zone 2 IR IN

Blue - Zone 1 IR IN

ELAN

C45P

XLINK

ST1

ST2

ST3

ST4

-

SIR

GND

1

Z-BUS

INT

2 EXT

PVIA4 Rear

IR

IR

4

G

IR

3

G

IR

2

G

IR

1

G

V+

G

V+

G

485+

485-

IR

ST

VIA1

485+

485-

IR

ST

V+

G

V+

G

VIA2

485+

485-

IR

V+

G

V+

G

ST

VIA3

V+

G

V+

G

485+

485-

IR

ST

VIA4

4

-

+

3

-

+

2

-

+

1

-

+

PWR

GROUND

CONN

Olé2XL

ELAN

C45P

Wh/Brown - +16V

Brown - GND

Wh/Green - +16V

Green - GND

Wh/Orange - V485+

Orange - V485-

Wh/Blue - IR OUT

Blue - N/C

485+

485-

IR

ST

V+

G

V+

G

VIA1

Z•630

IR INPUTS

Page 26



Olé2XL

3. Programming

Olé2XLs must be programmed with ELAN’s VIA!

®

TOOLS Setup Software using a PC running Windows XP. Downloads are facilitated through the USB

Download port on the front of the unit.

Note: A Standard USB-A to USB-Mini-B cable must be utilized for programming and is not included with the Olé2XL.

To Download a VIA!TOOLS Project:

• Connect a Standard USB-A to USB-Mini-B cable between a USB port

on a PC and the USB Download Port on the front of the Olé2XL

Touchpad.

• Access the VIA!TOOLS Transfer Page and click on the START Button.

• Wait until “DONE OK” is displayed in the window before disconnecting

the USB cable from the USB Download Port.

Please see VIA!TOOLS “Help” file for complete step-by-step information on programming Olé2XL Touchpads.

USB

Download

Port


Page 27

Olé2XL


Feature Enable/Disable

Speaker

Olé2XL features a small speaker that allows audible feedback signals to be heard as a result of button pushes. This feature can be disabled in

VIA!TOOLS setup software. See VIA!TOOLS Help File for specific instructions.

IR Senso

r

Olé2XL’s features a built-in IR Sensor. IR signals from a hand-held IR remote control pass through the IR sensor and travel to the head-end location where they control IR sources located there. These sources may be connected to an ELAN Multi-Zone Controller or an IR distribution network.

The IR Sensor can be disabled in VIA!TOOLS setup software. See VIA!TOOLS

“Help” File for specific instructions.

Light Sensor Enable/Disable

The Light Sensor feature is available on any Olé2XL Touchpad. It will be automatically available once the touchpad is downloaded to using VIA!™TOOLS version 7.1 or higher.

1. Install the unit in the wall, using the Film and wall plate that will be

used in the final installation. The specific Film and Trim Plate utilized

are integral to the Light Sensor functionality.

2. Adjust the room lighting to the brightest setting possible.

3. Select a Source on the touchpad. The Light Sensor function only works

when the unit displays the Source Icon screen.

4. Press and hold the "SELECT" button for five seconds. Depending on

the currect state of the sensor, a message will be displayed:

"Release button to ENABLE sensor” OR

"Release button to DISABLE sensor"

Once the button is released, a confirmation message will be sent:

Either "LIGHT SENSOR ENABLED" OR "LIGHT SENSOR DISABLED"

When the Light Sensor is enabled, the Olé2XL Touchpad's backlight will brighten or dim depending on the room's ambient light conditions. When the sensor is disabled, the Olé2XL remains at full brightness no matter what the ambient light conditions are like.

Page 28



Olé2XL

4. Troubleshooting

Power

Symptom Cause

Olé2XL does not power up.

1. RJ-45 plug crimped incorrectly; or wiring pinout of RJ-45 reversed.

2. Break in Cat-5 between Zone and

“Head-End”.

3. Power Supply not connected; or no longer functioning.

Solution

Verify wiring pinout and RJ-45 crimp. Correct by re-crimping

RJ-45 to Cat-5 cable.

Check RJ-45 to RJ-45 connections with cable tester if possible. Test Precision Panel connections by “Dead-Ending” wires at Precision Panel and testing at the Zone RJ-45 with a

Voltmeter set to “Continuity”.

Check AC outlet for power

(reset breaker if tripped) making sure Power Supply is securely plugged in. Test Power Supply with Voltmeter set to test

DC Volts. ELAN Multi-Room

Controllers Zone power can be tested using a C45P “Pigtail” and Voltmeter set to test for DC

Voltage.


Page 29

Olé2XL


IR

Symptom Cause

No control of

IR sources.

1. Programming: missing or incorrect IR commands.

2. Wiring: Incorrect wiring between Zone and

‘Head-End”.

3. Wiring: IR emitter connected to wrong source IR port of multiroom controller.

IR emitter defective.

IR flooding.

Intermittent source control.

Solution

Verify and correct programming. Test IR commands from

VIA!TOOLS.

Verify and correct wiring.

Verify port connection and correct.

Replace IR emitter.

Check to see if ambient light is shining on built in IR receiver or in direct line with plasma tv noise. If the Olé2XL cannot be relocated, disable the IR receiver in VIA!TOOLS setup software and use a plasma friendly external receiver as shown on page

16 of this manual. If installed in conjunction with an ELAN multi-room controller, check the

IR indicator on the controller. If it flickers or is constantly lit, IR flooding is indicated.

Page 30



Olé2XL

RS-232

Symptom

No serial control of system; “V-

Net RECV error” displayed, no feedback.

Sources select;

“System Off” displayed, no feedback.

No serial control of source;

“Com error, name of device” displayed, no feedback.

Cause

RS-485 signal or wiring between

Zone and “Head-

End” compromised.

V-Net/Z-Net switch set to Z-Net

RS-232 cable between source and SS1 System

Station/SC4 disconnected or connected to wrong port.

Solution

Verify and correct wiring, if using

SPP Precision Panel verify switch is set to SS1/SC4 position. For

PVIA4/10, make sure jumpers are set to INT.

Set switch to V-Net mode, control should resume momentarily.

Verify connection, replace serial cable if needed.


Page 31

Olé2XL


Notes:

Page 32


Limited Warranty

ELAN HOME SYSTEMS L.L.C. ("ELAN") warrants the Olé2XL Film Interactive

Touchpad to be free from defects in materials and workmanship for the period of two years (2 years) from date of purchase. If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly notifies ELAN in writing, ELAN shall repair or replace the item at the company's option. This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment which shall have been installed by other than an ELAN authorized installer, (c) to installed equipment which is not installed to ELAN's specifications, (d) to equipment which shall have been repaired or altered by others than ELAN, (e) to equipment which shall have been subjected to negligence, accident, or damage by circumstances beyond

ELAN's control, including, but not limited to, lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events beyond ELAN's control, or to improper operation, maintenance or storage, or to other than normal use of service. With respect to equipment sold by, but not manufactured by ELAN, the warranty obligations of ELAN shall in all respects conform to the warranty actually extended to ELAN by its supplier. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement.

Except as may be expressly provided and authorized in writing by ELAN,

ELAN shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured by ELAN or services rendered by

ELAN.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL

OTHER EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES

OF TITLE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

ATTENTION: TO OUR VALUED CONSUMERS

To ensure that consumers obtain quality pre-sale and after-sale support and service, ELAN Home Systems products are sold exclusively through authorized dealers. ELAN products are not sold online. The warranties on ELAN products are NOT VALID if the products have been purchased from an unauthorized dealer or an online E-tailer. To determine if your

ELAN reseller is authorized, please contact ELAN Home Systems at

(859) 269-7760.

Lexington, KY

www.elanhomesystems.com

®

P/N 9900877 REV:A

INSTR, INSTL, Olé2XL

LINEAR P/N 9900877 REV:A

INK: BLACK

MATERIAL: 60 LB WHITE COATED PAPER

PAGES: 36 PAGES

SCALE: 1-1

SIZE: 10.000 X 7.000, TOL: +/- .040

FOLDING: ALBUM FOLD CENTER STAPLE

FOLD TO 5.000 X 7.000

NOTE: ARTWORK CREATED BY ELAN HOME SYSTEMS

MANUAL MUST BE RoHS COMPLIANT

OleXL Installation Manual

Extra Large OLED

Olé

XL

Installation Manual

Contents

1. Introduction

2. System Design, Installation and

Connections

-

3. Programming

4. Troubleshooting

Limited Warranty

1. Introduction

Film Interactive Technology

Features

Installation & Usage Tips

Cleaning The Touch Screen

Specifications

Olé2XL-Front

Olé2XL-Rear

Films

2. System Design, Installation and

Connections

Planning

Installation

Pre-Wire

Rough-In

Mounting Height

Changing Films

Connectors/Pinout

3. Programming

To Download a VIA!TOOLS Project:

Feature Enable/Disable

Speaker

IR Senso

Light Sensor Enable/Disable

4. Troubleshooting

Power

IR

RS-232

Notes:

Limited Warranty

Related manuals

Elan

OLEXL

Elan

VIA!4.0-EM

Elan

VIA! VALET100EM

Elan

SS1

Elan

VIA! VALET100EM

Elan

VIA! 4.0

Elan

ViaValet 6.4

Elan

TS2

Elan

VDA16B

Elan

S86A

Table of contents