advertisement
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 1
Table of contents
2
2.1
2.2
3
3.1
3.2
3.3
3.4
3.5
3.6
1
1.1
1.2
1.3
Important 3
Safety 3
Care of the screen 3
Recycling 3
Your TV 4
Television overview 4
Product highlights 5
Getting started 5
Position the TV 5
Wall mounting - VESA 6
Remote control batteries 9
Antenna cable 9
Connect the mains 9
First time installation 9
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
6
6.1
6.2
6.3
6.4
6.5
Use your TV 10
Switch on or off - Standby 10
Watch TV 11
Watch channels from a digital receiver 11
Watch connected devices 11
Watch a DVD 12
Select a Teletext page 12
Change Ambilight mode 13
5 Use more of your TV 14
5.5
5.6
5.7
5.8
5.1
5.2
5.3
5.4
Remote Control 14
TV menu overview 17
Picture and sound settings 19
Ambilight 23
Teletext 23
Create favourite channel lists 25
Timers and locks 26
Subtitles 27
5.9
View and play photos, MP3... 28
5.10
Software update 30
Channel installation 32
Automatic channel installation 32
Manual channel installation 32
Rearrange stored channels 33
Automatic channel management 34
Factory settings 34
7
7.1
7.2
7.3
7.4
8
9
10
Connections (DVD, receiver, ...) 35
Connections overview 35
About connecting 36
Connect your devices 38
Connections setup 43
Technical data 44
Troubleshooting 45
Index 47
Register your product and get support at www.philips.com/welcome.
Table of contents 1
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 2
2007 © Koninklijke Philips Electronics
N.V. All rights reserved. Specifications are subject to change without notice.
Trademarks are the proper ty of
Koninklijke Philips Electronics N.V. or their respective owners.
Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly.
The material in this manual is believed adequate for the intended use of the system. If the product, or its individual modules or procedures, are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained. Philips warrants that the material itself does not infringe any United States patents.
No fur ther warranty is expressed or implied.
Open source software
This television contains open source software. Philips hereby offers to deliver or make available, upon request, for a charge no more than the cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code on a medium customarily used for software interchange.
This offer is valid for a period of 3 years after the date of purchase of this product. To obtain the source code, write to
Philips Innovative Applications N.V.
Ass. to the Development Manager
Pathoekeweg 11
B-8000 Brugge
Belgium
Copyrights
VESA, FDMI and the VESA
Mounting Compliant logo are trademarks of the Video Electronics
Standards Association.
Manufactured under license from Dolby Laboratories.
‘Dolby’, ‘Pro Logic’ and the double D symbol
G
, are trademarks of Dolby
Laboratories.
Manufactured under license from BBE Sound, Inc.
Licensed by BBE, Inc under one or more of the following US patents: 5510752,
5736897. BBE and BBE symbol are registered trademarks of BBE Sound Inc.
Warranty
No components are user-serviceable.
Do not open or remove covers to the inside of the product. Repairs may only be done by Philips Service Centres and official repairshops. Failure to do so shall void any warranty, stated or implied.
Any operation expressly prohibited in this manual, any adjustments, or assembly procedures not recommended or authorised in this manual shall void the warranty.
Pixel characteristics
This LCD product has a high number of colour pixels. Although it has effective pixels of 99,999% or more, black dots or bright points of light (red, green or blue) may appear constantly on the screen.This
is a structural property of the display
(within common industry standards) and is not a malfunction.
Compliance with EMF
Koninklijke Philips Electronics N.V.
manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.
One of Philips’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.
Philips is committed to develop, produce and market products that cause no adverse health effects.
Philips confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today.
Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardisation for early integration in its products.
Windows Media is either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries
® Kensington and MicroSaver are registered US trademarks of ACCO
World Corporation with issued registrations and pending applications in other countries throughout the world.
All other registered and unregistered trademarks are the proper ty of their respective owners.
2
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 3
1 Important
Read this user manual before you star t to use this product.
Pay attention to this section and closely follow the instructions. The warranty does not apply to damage caused by not taking into account the instructions.
• Stationary images
Avoid stationary images as much as possible. If you can not, reduce screen contrast and brightness to prevent damage to the screen.
Stationary images are images that remain on the screen for a long time. Examples of stationary images are: on screen menus, teletext pages, black bars, stock market information,TV channel logos, time displays, and so on.
1.3
Recycling
1.1
Safety
• To avoid shor t circuit, do not expose the product to rain or water.
• To avoid a risk of fire or electric shock do not place naked flame sources (e.g. lighted candles) close to the TV.
• Leave a space of at least 10cm (4 inches) all around the TV for ventilation.
• Keep away from radiators or other heat sources.
• Do not install the TV in a confined space such as a book case. Make sure that cur tains, cupboards and so on cannot obstruct the air flow through the ventilation slots.
• Make sure the TV can not fall down. Place the TV on a solid and flat surface and only use the stand provided with the TV.
• To prevent damaging the mains cord which may cause a fire or electric shock, do not place the TV on the cord or anything else that can pinch the cord.
• When mounted on a swivel stand or VESA wall bracket avoid force coming on the mains plugs.
Par tly loosened mains plugs can cause arcing or fire.
• Take the packaging to your local recycling centre.
• Dispose old batteries safely according local regulations.
• This product is designed and manufactured for material recycling and re-use.
• This product should not be disposed with other household waste. Inform yourself or ask your dealer about local environmentally safe recycling and local regulations. Uncontrolled waste disposal harms the environment and human health.
(EEC 2002/96/EC)
1.2
Care of the screen
• Unplug the TV before cleaning.
• Clean the surface with a soft damp cloth. Do not apply any other substance (chemical or household cleaning agent). This may damage the screen.
• Do not touch, push or rub or strike the screen with anything hard as this may scratch, mar or damage the screen permanently.
• To avoid deformations and colour fading, wipe off water drops as soon as possible.
Important 3
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 4
2 Your TV
This section gives you an overview of the controls and functions of this TV.
2.1
Television overview
Side controls
3
5-6
B
1 Volume up and down
2 Menu
3 Program or Channel up and down
4 Power switch
5 Led indicator (Blue: On; Red: Standby)
6 Remote control sensor
4
Side connectors
1
2
Remote control
B
INPUT v
TV DVD STB HTS
DEMO
OPTION
GUIDE a
OK
LIST
MENU
BROWSE
+ b
+
¬
4
7 i
-
V
1 2
5
8
0
Ò
®
‡
MHEG CANCEL j
π b
† q
6
9
R
-
3
P
1
2
3
4
5
6
7
8
9
To connect a camera, game console, headphone or a USB memory device.
Back connectors
1 Standby or On
2 DVD, STB, ... device selection
3 Colour keys
4 Navigation key (up, down, left, right) OK
5 Teletext key
6 Menu key
7 Programme up or down
8 Volume up or down
9 Ambilight on or off
Find more on your remote control in section 5.1
Remote control overview.
To connect the antenna, DVD, VCR or other device.
4 Your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 5
2.2
Product highlights
Your new TV is equipped with some of the most modern audio or video innovations.
Your TV offers the following advantages ...
Full High Definition LCD display
A full HD resolution of 1920x1080p, the highest resolution of HD sources. It offers a brilliant flickerfree progressive scan picture with optimum brightness and superb colours.
Ambilight
For a more relaxed viewing experience and improved perceived picture quality.
Perfect Pixel HD
Offers perfect picture quality from any source.
100Hz Clear LCD
100Hz Clear LCD results in superior sharpness of motion reproduction, better black level,high contrast with a flicker-free, quiet image and a larger viewing angle.
HDMI connectors
3 HDMI connectors for highest quality high definition connectivity.
USB connection
Multimedia connection for instantly view or play your photos or music.
3 Getting started
This section helps you with the positioning and the first time installation of the TV.
3.1
Position the TV
) Warning
Carefully read the safety precautions in section 1.1
Safety before you position the TV.
Large screen TVs are heavy. Carry and handle the
TV with at least two persons.
Connect your devices first before you position your
TV or mount it on the wall.
The ideal viewing distance for watching TV is three times its diagonal screensize.
For ideal viewing conditions, position the TV where light does not fall directly on the screen.
Best Ambilight effect is watched in a room with dimmed lighting conditions.
For the best Ambilight effect, position the TV 10 to
20 cm away from the wall. Position the TV where sunlight does not fall directly on the TV.
Kensington Security Slot
Your TV is equipped with a Kensington Security Slot at the back of the TV for an anti-theft lock.
An anti-theft Kensington lock has to be purchased separately.
Your TV 5
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 6
3.2
Wall mounting
3.2.2
Mounting the wall mount bracket
You can wall mount the TV with the supplied wall mount bracket.
3.2.1
Unmounting the TV stand
The TV stand should be unmounted from the TV to allow the TV to be wall mounted.
‡ Unscrew the 4 screws that secure the stand to the TV.
) Caution
Wall mounting the TV requires special skills that should only be performed by qualified personnel.
Wall mounting the TV should meet safety standards according to the TV’s weight.
Koninklijke Philips Electronics N.V. bears no responsibility for improper mounting or mounting that results in accident or injury.
Read also the safety precautions in section
1.1 Safety before you position the TV.
‡ Collect the parts for wall mounting.
® Lift the TV from the stand.
2x A 2x B
® Insert just a little bit both security screws in the wall mount bracket.
2
Ò Verify the presence of the 4 plastic discs at the back of the TV.
6 Your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 7
† Mount the 2 spacers on the 2 lower discs at the back of the TV.
‹ Connect all cables.
See section 7 Connections.
º Calculate your TV’s ideal position.
≈Lift the TV into the wall mount bracket.
42"
1 121m m
260,5 mm
2
30kg
◊Position and level the wall mount bracket and fix the bracket firmly to the wall.
Ú Secure the TV in the bracket by screwing in the
2 already fitted screws .
Your TV 7
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 8
3.2.3
VESA compliant mounting
) Caution
Use a VESA compliant bracket that meets safety standards according to the TV’s weight.
Closely follow the instructions that come with your
VESA compliant bracket to mount the TV.
Koninklijke Philips Electronics N.V. bears no responsibility for improper mounting or mounting that results in accident or injury.
The TV is prepared for VESA compliant mounting.
This bracket is not included.
Use a VESA compliant bracket with code
VESA MIS-F, 600, 400, 8.
Prepare the TV for VESA compliant mounting.
‡ Locate the VESA screwholes on the back of the
TV.
400
M8
600
® Should the plastic discs obstruct the VESA bracket, you can unscrew these 4 discs.
4x
8 Your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 9
3.3
Remote control batteries 3.5
Connect the mains cord
‡ Verify that your mains voltage corresponds with the voltage printed on the sticker at the back of the TV. Do not inser t the mains cord if the voltage is different.
® Insert the mains cord tightly.
‡ Open the battery cover on the back of the remote control.
® Insert the 3 batteries supplied (Type AAA-
LR03-1,5V). Make sure the + and - ends of the batteries line up correctly (inside of case is marked.)
Ò Close the cover.
rNote
Remove the batteries if you don’t use the remote control for a long time.
3.4
Antenna cable
The TV is never powered off completely unless the mains cord is physically unplugged. Therefore the mains plug must be accessible at all time.
ANTENNA
3.6
First time installation
The first time, and only the first time, the mains cord is inser ted, the installation procedures star ts up automatically. Follow the instructions on screen.
Please select your language...
Menu language
English
Français
‡ Locate the antenna connection at the back of the TV.
® Insert the antenna cable tightly into the antenna socket x Antenna.
using cursor up and down
Next
à Tips
• If you notice you have selected a wrong language, press the red key on the remote control to return to the language selection menu.
• To rearrange the stored channels, see section 6.3
Rearrange stored channels.
Your TV 9
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 10
4 Use your TV
Learn how to operate your TV for daily use.
4.1
Switch on or off - Standby
To switch on the TV:
• Press B Power at the right side of the TV if the standby led is off.
• Press B on the remote control if the standby led in on.
To switch to standby:
• Press B on the remote control.
To switch on from standby without remote control:
• Press B Power at the side of the TV to switch off first and press B Power again to switch on.
B
B
INPUT v
TV DVD STB HTS
To switch off:
• Press B Power at the side of the TV.
rNote
Energy consumption contributes to air and water pollution. As long as the mains cord is plugged in, the TV consumes energy. This TV has a very low standby power consumption.
10 Use your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 11
4.2
Watch TV 4.3
Watch channels from a digital receiver
4.2.1
Switch channels
‡ To switch TV channels:
• Press a number or press P+ or P- on your remote control.
• Press Program/Channel - or + on the side controls of the TV.
® Press R to return to the previously viewed TV channel .
b
BROWSE
+ +
+
¬
-
V
-
P
-
1 2 3
P
4 5 6
8 9
0 - 9
7 i 0 R R
‡ Switch on the digital receiver.
The picture from your receiver might appear automatically on your screen.
® Use the remote control of your digital receiver to select TV channels.
If the picture does not appear :
‡ Press v on the remote control.
INPUT v
DEMO
OPTION
GUIDE a
® Press v repeatedly to select the device. Wait a few seconds until the picture appears.
Ò Press OK .
† Use the remote control of the digital receiver to select TV channels.
4.2.2
Adjust volume
‡ To adjust the volume:
• Press V + or - on the remote control
• Press Volume + or - on the side controls of your TV.
® To mute the sound:
• Press ¬ on the remote control
• Press ¬ again to restore the sound.
b
+
MENU
BROWSE
+ +
¬
-
V
¬
-
V
1
4
7
2
5
8
6
9
-
3
P
4.4
Watch connected devices
‡ Switch on the device.
The picture from your device might appear automatically.
If the picture does not appear :
® Press v on the remote control.
Ò Press v repeatedly to select the device. Wait a few seconds until the picture appears.
† Press OK .
º Use the remote control of your device to select
TV channels.
B
INPUT v
TV DVD STB HTS
Use your TV 11
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 12
4.5
Watch a DVD
‡ Insert a DVD disc in your player.
® Press Play π.
The picture from your player appears automatically on your screen.
If the picture does not appear :
‡ Press v on the remote control.
INPUT v
B
INPUT v
TV DVD STB HTS
DEMO
OPTION
GUIDE a
4.6
Select a Teletext page
Most TV channels broadcast information via
Teletext. TV channels often broadcast information via Teletext. If Teletext is available only English
Teletext is suppor ted. China does not suppor t this function due to no Teletext available.
To watch Teletext:
‡ Press b.
The main index page appears.
LIST
® Press v repeatedly to select the DVD player.
Wait a few seconds until the picture appears.
Ò Press OK .
† Press Play π.
b
MENU
BROWSE
+ b
+
¬
-
V
-
P
® To select a page of your choice:
• Enter the page number with the number keys.
• Press P- or P+ or navigation key up or down to view the next or the previous page.
• Press a colour key to select one of the colour coded items at the bottom of the screen.
à Tip
Press R to return to the previously viewed page.
Ò Press b again to switch Teletext off.
For more information on teletext, see section 5.5
Teletext.
12 Use your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 13
4.7
Change Ambilight mode
You can choose among three Ambilight modes and change the light intensity:
• Relaxed
Sets Ambilight to change soft and smoothly with the images on screen.
• Moderate
Sets Ambilight between Relaxed and Dynamic.
• Dynamic
Sets Ambilight to change quick and responsive.
To change the Ambilight mode:
‡ Press Ambilight to switch on or off.
4 5 6
7 i
8
0
9
R
Ò
®
‡
MHEG CANCEL j
π b
† q
® Press Mode repeatedly to toggle through the
Ambilight modes.
Ò Press OK .
For more information on Ambilight, see section 5.4
Ambilight.
à Tip
To fully enjoy Ambilight, switch off or dim the room lights.
To change the light intensity of Ambilight:
‡ Slide the Aurea Ambilight switch up or down to change the light intensity.
TV standby with Ambilight
When the TV is in standby, you can switch
Ambilight on.
‡ Press Ambilight on the remote control when the TV is in standby.
® Press Mode repeatedly to select the available colours.
Use your TV 13
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 14
5 Use more of your TV
This section deals with the more advanced use of your TV:
• how to use the menus
• to adjust the picture, sound and Ambilight settings
• more about Teletext, if available
• how to create favourite channel lists
• how to set locks and timers
• to set subtitles and select a subtitle language
• how you can view your photos or play your favourite music from a USB memory device.
5.1
Remote control
5.1.1
Remote control overview
25
24
23
22
21
20
19
18
B
INPUT v
TV DVD STB HTS
DEMO
OPTION
GUIDE a
OK
LIST
MENU
BROWSE
+ b
+
¬
-
V
7 i
1
4
2
5
8
0
Ò
®
‡
MHEG CANCEL j
π b
† q
6
9
R
-
P
3
6
7
8
9
10
11
12
13
14
15
16
17
1
2
3
4
5
1 Standby B
To switch the TV on or back to standby.
2 Input v
To select a connected device or to return to
TV.
3 TV DVD STB HTS
To control connected devices.
4 Colour keys
• Easy selection of teletext pages.
• Easy selection of tasks.
5 Guide a
No function
6 OK /List
• To display the channel list.
• To activate a setting.
7 Navigation keys (up, down, left, right)
To navigate the menu.
8 Teletext b
To switch teletext on or off, if available
9 +P- Channel up or down
To switch to the next or previous channel in the channel list.
10 Mute ¬
To mute the sound or restore it.
11 Number keys
To select a TV channel.
12 Previous channel R
To return to the previously viewed channel
13 Audio and video keys Ò‡π†®
To use with connected devices.
14 Widescreen Picture format q
To select a picture format.
15 Dual screen b
To show teletext on the right and the picture on the left of the screen.
16 Mode
To toggle through the Ambilight modes
17 Ambilight AUREA
To change the light intensity of Ambilight
14 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 15
18 Ambilight
To switch Ambilight on or off.
19 Subtitles j
To activate or deactivate the subtitle mode.
20 ‡ MHEG cancel (only for UK)
No function
21 On screen information i
To show channel or programme information if available.
22 Volume up or down V
To adjust the volume.
23 Menu
To switch the menu on or off.
24 Option
To switch the Quick access menu on or off.
25 Demo
To switch the Demo menu on and to get a demonstration of the features of the TV.
5.1.2
Operate other Audio/Video devices
This TV remote control can operate DVD devices,
Set-Top Boxes and Home Theater Systems of
Philips and many other brands. If the keys do not operate the selected device, a setup is required to programme the remote control for your specific brand and type of device.
TV DVD STB HTS
B
INPUT v
TV DVD STB HTS
DEMO
OPTION
GUIDE a
See section 10 Index to find the section in the manual about a specific remote control key.
5.1.3
Set to operate a particular device
There are two ways to programme the remote control for a device of a par ticular manufacturer.
You can enter a manufacturer's code or star t an auto-search.
The manufacturer's setup codes contain:
• for DVD: DVD, DVD-R, HDD DVD-R, Blu-ray
• for STB: Satellite tuners, Settop box tuners/decoders, Cable tuners/decoders
• for HTS: Home Theater Systems, Audio/Video systems
The setup codes for most used Philips devices are:
DVD 001 Factory pre-set Philips DVD
DVD-Harddisk 005 Philips DVD-Recorder Harddisk
BluRay
STB (39)
006 Philips HD BluRay player
002 Factory pre-set Philips Set-Top Box
STB (40)
HTS
007 (for some Philips Set-Top Boxes)
003 Factory pre-set Philips Home Theater
System
There is a wider selection of Philips devices that can be programmed.
For other manufacturer's entry codes tables, see the end of this manual.
rNote:
The remote control might not be compatible with all types of DVD, Set-Top Boxes and Home Theater
Systems
Use more of your TV 15
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 16
Enter the setup code directly
‡ Press the DVD, STB or HTS key for 4 seconds to select the device mode you need.
The selected mode key will light up constantly.
® Enter the three-number code for the type and brand of your device. Most brands have more than one entry code.
If you entered the correct code, all mode keys will blink to confirm the selection.
If you entered a wrong code, all mode keys will light up for 2 seconds. Repeat Step 2 with a different code.
Ò Point the remote control at the device, and press B to test if the code is correct for your device.
If successful try whether all functions can be operated. If not succesful, or if not all functions can be operated, repeat Step 1 and 2 with one of the other setup codes for your manufacturer.
correct code for your device or press OK again to continue the automatic search.
5.1.4
Operate DVD, Set-Top Box and
Home Theater devices
‡ Press the DVD, STB or HTS key to set the remote control to operate the device you need.
® Use the TV remote control to operate the device.
If the keys do not operate the selected device, a setup is required to programme the remote control for your specific brand and type of device. See section 5.1.3
Ò Press the TV key to return to normal TV mode.
When not used, the remote control will switch back to TV mode after 30 seconds.
OPTION
DEMO
OPTION
GUIDE a a
Automatic search of all codes
If you are not successful in finding the correct brand or code, you can try an automatic search of all codes. The automatic search might take several minutes.
If after the automatic search no code is successful, the remote control will likely not be able to operate your par ticular device. In such case, use the device's own remote control.
‡ Switch on the device you want the TV remote control to set up for.
®. Point the remote control to the device.
Ò To select the device mode you need, press the
DVD, STB or HTS key for 4 seconds.
The selected mode key will light up constantly.
† Press OK to start the automatic search.
Every two seconds, when a new code is sent, the B key will blink.
Keep pointing the remote control to the device.
º When the device switches off, press OK to stop the search.
◊Press B to switch on your device.
‹ Use the remote control keys to try if all functions can be operated.
If not all functions can be operated, press OK again to continue the automatic search for a correct code.
≈If all functions can be operated, press the currently selected device mode key to confirm and to quit the automatic search.
rNote:
To pause the automatic search, press OK. Press the navigation key up or down to search for the codes one by one backward or forward to locate the
MENU
OK
LIST b
MENU
BROWSE
+ +
+ +
¬
-
V
4
7 i
-
V
1 2
5
8
0
6
9
R
3
-
P
P
-
†
Ò
®
‡
MHEG CANCEL j
π b
† q
When the remote control is selected for a par ticular device all keys have the same function except the keys mentioned here.
Ò
• DVD player, DVD recorder, DVD-HDD
Option key = DVD System menu
Menu key = DVD Disc menu
P+/- = DVD Next/Previous track
• Philips DVD Recorder (setup code 004)
Ò key = DVD previous track
† key = DVD next track
• Philips DVD recorder with HDD (setup code
005)
Option key = DVD-R HDD Disc menu
Menu key = DVD-R HDD browser
Ò key = DVD-R HDD previous track
† key = DVD-R HDD next track
16 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 17
• Philips Blu-ray Disc player (setup code 006)
Option key = BD Home screen a key = BD Content menu
Menu key = BD Disc menu
• Digital or Satellite receiver
No change of functions.
• Home Theatre System
Option key = HTS Set up
Menu key = HTS Disc menu
V key = HTS volume
P+/- = HTS Next/Previous
5.2
TV menu overview
With the on screen menus you install your TV, adjust picture, sound and Ambilight settings and access features. This section gives an overview of the menus and describes how to navigate.
5.2.1
The menu
‡ Press Menu on the remote control to show the main menu.
® Press Menu to quit the menu.
LIST
5.1.5
Keep the remote in the chosen mode permanently
If you operate a device selecting the DVD, STB or
HTS key, the remote control will return to TV mode if you do not use it for 30 seconds.
You can also set up the remote control to stay in the selected mode permanently.
‡ Press the TV key to be in TV mode.
® Press OK and ¬ at the same time for 4 seconds.
The B key will blink for 1 second to confirm.
From now on the remote control will stay in the selected device mode.
Ò Press the TV, DVD, STB or HTS key to operate the device you need.
The B key will blink a few times to confirm the selection.
5.1.6
Remote control entry codes tables
See the end of this manual.
Television
Multimedia
MENU
BROWSE
TV menu
Channel list
MENU
BROWSE
+
-
V
¬ b
+
-
P
The main menu offers the following items:
• TV menu
Select this menu for installation, picture and sound settings, Ambilight and other feature settings.
• Channel list
Select this item to show the Channel list.
Create your Favourite channel lists here.
• Multimedia
Select this item to view photos or play music stored on a USB device. See section 5.10 View and play photos, MP3, ...
Use more of your TV 17
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 18
5.2.2
Use of the menu
Learn to use the menus with this example.
‡ Press Menu on the remote control.
DEMO
OPTION
GUIDE a
®
OK
LIST
MENU
BROWSE b
MENU
BROWSE
The main menu appears on the screen.
Television TV menu
Channel list
Multimedia
® Press navigation key right to enter the TV menu.
TV menu settings
Features
Installation
Software update
TV settings
Settings assistant
Reset to standard
Picture
Sound
Ambilight
Ò Press navigation key right to enter the TV settings menu.
TV settings Settings assistant
Reset to standard
Picture
Sound
Ambilight
Start now
º Press navigation key right to enter the picture settings.
Picture
Contrast
Brightness
Colour
Hue
Sharpness
Tint
...
90
47
52
0
4
Contrast
◊Press navigation key down to select Brightness.
Picture
Contrast
Brightness
Colour
Hue
Sharpness
Tint
...
0
4
98
47
52
Brightness
‹ Press navigation key right to enter the
Brightness setting.
Brightness
≈Press navigation key up or down to adjust the setting.
Ú Press navigation key left to return to the Picture settings or press Menu to quit the menu.
† Press navigation key down to select Picture.
TV settings
Reset to standard
Picture
Sound
Ambilight
Picture
Contrast
Brightness
Colour
Hue
Sharpness
Tint
Perfect Pixel HD
...
18 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 19
5.2.3
Quick access menu
The Quick access menu gives direct access to some often needed menu items.
5.3
Picture and Sound settings
This section describes how to adjust picture and sound in the menus.
‡ Press Option on the remote control.
® Press navigation key up or down to select an option.
Ò Press OK to show the selected option menu.
† Press navigation key up, down, left, right to adjust the settings in the menu.
º Press Option to quit the menu.
OPTION
INPUT v
TV DVD STB HTS
DEMO
OPTION
GUIDE a
OK
• Subtitles
See section 5.9 Subtitles.
• Picture format
See section 5.3.4 Widescreen picture format.
• Equalizer
See section 5.3.5 Adjust sound settings.
• Clock
Not applicable in case of no Teletext present.
Display the clock
‡ Press OK to display the clock permanently.
® Press Option and press navigation key up or down to select Clock again.
Ò Press OK to hide the clock.
5.3.1
Settings assistant
Use the Settings assistant to guide you through basic picture, sound and Ambilight settings in an easy way.
‡ Press Menu on the remote control and select
TV menu > TV settings > Settings assistant and press navigation key right to enter.
® Press OK .
Ò Press the green key on the remote control to star t the assistant.
† Press navigation key left or right to select the left or right side to make your choice.
º Press the green key to go to the next setting.
You will go through several settings. When finished the TV will ask you to store these settings.
◊Press the green key to store all your settings.
‹ Press Menu to quit the menu.
5.3.2
Reset to standards
Sets the TV to one of the predefined settings. Each setting combines picture, sound and Ambilight.
‡ Press Menu on the remote control and select
TV menu > TV settings > Reset to standard and press navigation key right to enter the list.
® Press navigation key up or down to select a setting.
Ò Press the green key to store your selection.
† Press Menu to quit the menu.
Quick access
Subtitle
Picture format
Equalizer
Clock
Standard settings: Current, Natural, Vivid, Movie
Use more of your TV 19
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 20
5.3.3
Picture settings
This section describes how to adjust all picture settings.
‡ Press Menu on the remote control and select
TV menu > TV settings > Picture and press navigation key right to enter the list.
® Press navigation key up or down to select a setting.
TV settings Picture
Settings assistant
Reset to standard
Picture
Sound
Ambilight
Contrast
Brightness
Colour
Hue
Sharpness
Tint
Perfect Pixel HD
HD Natural Motion
100Hz Clear LCD
Dynamic contrast
Noise reduction
MPEG artefact red.
Colour enhanc …
Active control
Picture format
• Contrast
Changes the level of bright par ts in the picture but keeps the dark par ts unchanged.
• Brightness
Changes the level of light of the total picture.
• Colour
Changes the level of saturation.
• Hue
If NTSC is broadcasted, this level compensates the colour variations.
• Sharpness
Changes the level of sharpness of fine details.
• Tint
Sets the colours to Normal, Warm (reddish) or
Cool (bluish). Select Custom to make a setting of your own in the Custom tint menu.
• Custom tint
If Custom is selected in the Tint menu you can make a setting of your own here.
Press the green key to select each bar to change the value of:
- R-WP red whitepoint
- G-WP green whitepoint
- B-WP blue whitepoint
- R-BL red blacklevel
- G-BL green blacklevel
• Perfect Pixel HD
Enables or disables Perfect Pixel HD, the most ideal picture setting.
• HD Natural Motion
Reduces the field and line flicker and reproduces smooth movement especially in movies.
Set the level to Minimum, Maximum or Off.
• 100 Hz Clear LCD
Switches 100 Hz Clear LCD on or off.
• Dynamic contrast
Enhances the contrast in the picture as the image on the screen changes.
Set the level to Minimum, Medium, Maximum or
Off. The level medium is recommended.
• Noise reduction
Filters out and reduces the noise in the picture.
Set the level to Minimum, Medium, Maximum or
Off.
• MPEG artefact reduction
Smoothens the transitions on digital pictures.
Switches MPEG ar tefact reduction on or off.
• Colour enhancement
Makes the colours more vivid and improves the resolution of details in bright colours.
Set the level to Minimum, Medium, Maximum or
Off.
• Active control
Corrects all incoming signals in order to provide the best picture possible.
Switches Active control on or off.
• Picture format
See section 5.3.4 Widescreen picture format.
20 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 21
5.3.4
Widescreen picture format
Avoid black bars on the sides or on top and bottom of the picture. Change the picture format to a format that fills the screen.
‡ Press q to switch on the Picture format menu.
4 5 6
7 i
8
0
9
R
Ò
®
‡
MHEG CANCEL j
π b
† q q
Unscaled
(Only for HD and PC.)
Maximum sharpness.
Distor tion may appear on borders. Black bars may appear with pictures from your PC.
rNote
Do not forget to name the connection in the
Connection menu. See section 7.4.3 Naming your devices.
® Press navigation key up or down to select an available picture format.
Ò Press navigation key up to shift the picture upwards to make par tly covered subtitles visible.
à Tip
The Auto format setting is recommended for minimal distor tion .
Auto format (Not for PC.)
Enlarges the picture automatically to fill the screen. Subtitles remain visible.
Super zoom (Not for HD.)
Removes the black bars on the side of 4:3 broadcasts.
There is a minimal distor tion.
4:3 (Not for HD.)
Shows the classical 4:3 format.
Movie expand 14:9
(Not for HD.)
Scales classical 4:3 format to
14:9.
Movie expand 16:9
(Not for HD.)
Scales classical 4:3 format to
16:9.
Wide screen
Stretches 4:3 format to 16:9.
Use more of your TV 21
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 22
5.3.5
Sound settings
This section describes how to adjust all sound settings.
‡ Press Menu on the remote control and select
TV menu > TV settings > Sound and press navigation key right to enter the list.
® Press navigation key up or down to select a setting.
TV settings
Settings assistant
Reset to standard
Picture
Sound
Sound
Equalizer
Volume
Dual I/II
Mono/Stereo
Surround mode
• Automatic volume leveller
Reduces sudden volume differences like at the beginning of commercials or when switching from one channel to another.
Select on or off.
• Delta volume
Levels out volume differences between channels or connected devices.
‡ Switch to the channel or device you want to level out the volume difference.
® Select Delta volume in the Sound menu and change the volume level.
• Auto surround
Switches the TV automatically to the best surround sound mode broadcasted.
Select on or off.
Delta volume
Auto surround
• Equalizer
Changes the bass and treble of the sound. Select each bar to change the setting. See also section
5.2.3 Quick access menu.
• Volume
Changes the volume.
When adjusting the volume with V a volume bar appears. If you don’t want it to appear go to
TV menu > Installation > Preferences and press navigation key right to enter the list and select
Volume bar off.
‡ Press navigation key up or down to select
Volume bar.
® Press navigation key right to enter.
Ò Select On to activate the temporarily display of the volume bar when adjusting the volume.
• Balance
Sets the balance of the left and right loudspeakers to fit best your listening position.
• Dual I/II
If broadcasted, you can choose between two different languages.
• Mono/stereo
If stereo broadcasting is available, you can select
Mono or Stereo per TV channel.
• Surround mode
To select a more spatial sound if broadcasted or if available from a connected device.
• Headphone volume
Changes the volume of the headphone.
You can mute the TV speakers with ¬ on the remote control.
22 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 23
5.4
Ambilight 5.5
Teletext
This section describes how to adjust Ambilight settings.
‡ Press Menu on the remote control and select
TV menu > TV settings > Ambilight and press navigation key right to enter the list.
® Press navigation key up or down to select a setting.
If available only English Teletext is suppor ted. China does not suppor t this function due to no Teletext available.
Your TV has a 1200 pages memory that stores broadcasted teletext pages and subpages to reduce waiting time.
TV settings
Settings assistant
Reset to standard
Picture
Sound
Ambilight
Ambilight
Ambilight
Brightness
Mode
Separation
Colour boost
• Ambilight
Switches Ambilight on or off.
• Brightness
Changes the light output of Ambilight.
• Mode
You can choose among three Ambilight modes:
Relaxed, Moderate, Dynamic. See section 4.7
Change Ambilight mode.
• Separation
Sets the level of difference in colour between the left, right, top and bottom side of the TV.
Separation off shows a dynamic but mono colour
Ambilight.
• Colour boost
Amplifies the colours for a more dynamic effect.
ç Caution
To avoid bad infrared remote control reception, place your devices out of sight of Ambilight.
To select a teletext page see section 4.6 Select a
Teletext page.
5.5.1
Select pagenumber subpages
A teletext page number can hold several subpages.
The pages are shown on a bar next to the main pagenumber.
‡ Press b.
® Select a teletext page.
Ò Press navigation key left or right to select a subpage.
5.5.2
Dual screen teletext
View the TV channel and teletext next to each other.
‡ Press b for Dual screen teletext.
® Press b again to show normal teletext .
Ò Press b to switch off teletext.
5.5.3
Search teletext
Quickly jump to a subject linked to a series of pagenumbers or search for specific words in teletext pages.
‡ Press b.
® Press OK to highlight the first word or number.
Ò Press navigation key left, right or up, down to jump to the next word or number on the page.
† Press OK to search a page which holds the highlighted word or number.
º Press navigation key up until no word or number is highlighted to quit Search.
Use more of your TV 23
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 24
5.5.4
Enlarge teletext pages
For a more comfor table reading, you can enlarge the teletext page.
‡ Press b and select a teletext page.
® Press Option on the remote control to enlarge the top par t of the page.
Ò Press Option again to view the enlarged lower par t of the page.
† Press navigation key up or down to scroll through the enlarged page.
º Press Option again to return to the normal page size.
INPUT v
TV DVD STB HTS
5.5.6
Teletext 2.5
If broadcasted by the TV channel this teletext offers more colours and better graphics.
Teletext 2.5 is switched on as a factory setting.
‡ Press Menu on the remote control and select
TV menu > Installation > Preferences >
Teletext 2.5 and press navigation key right to enter the list.
® Select on or off.
DEMO
OPTION
GUIDE a
OPTION
OK
5.5.5
Teletext menu
With the options in the teletext menu you can reveal hidden info, let cycle subpages automatically and change the character setting.
• Reveal
Hide or unhide hidden information on a page, such as solutions to riddles or puzzles.
• Cycle subpages
If subpages are available for the selected page, you can make subpages cycle automatically.
• Language
Some languages use a different set of characters.
Switch to the other group to show the text correctly.
‡ Press b.
® Press Menu.
Teletext menu
Reveal
Cycle subpages
Language
Off
Off
Gr. II
Ò Press navigation key up or down to select an option.
† Press OK to change a setting.
º Press Menu to quit the teletext menu.
◊Press b to switch off teletext.
24 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 25
5.6
Create favourite channel lists
View the All channels list or set up a Favourite list of your own with your preferred TV channels. For example, each member of your family can create his or her own favourite list.
5.6.3
Select a channel from a favourite list
‡ Press OK .
The last selected channel list appears.
® Use navigation key up or down to highlight a channel.
Ò Press OK .
The TV tunes to that channel.
5.6.1
Select a favourite list
Learn how to select one of the favourite channel lists.
‡ Press OK .
The first time after you have finished the installation, the All channels list is shown. In other situations, it brings up the last selected favourite list.
All channels
....
AV 3
HDMI ...
1 Channel 1
2 Channel 2
3 Channel 3
4 Channel 4
....
Select list
à Tip
• Use -P+ to go through the TV channels of the selected favourite list.
• With the number keys you can still select channels which are not marked as favourite.
MENU b
BROWSE
+ +
+
¬
-
V
1
4
7 i
8
0
2
5 6
9
R
-
P
3
-
P
0 - 9
Ò ‡ π †
® Press the red key to show all favourite lists.
Ò Press navigation key up or down to select a list.
† Press OK .
The selected favourite list appears.
º Press OK again to quit.
5.6.2
To set up a favourite list
Create or modify your own favourite list.
‡ Press OK .
The last selected list appears.
® Press the red key to show all favourite lists.
Ò Press navigation key up or down to select a list.
† Press OK .
º Press the green key to enter the Edit mode.
The selected list brings up a full channel list.
◊Press navigation key up or down to highlight a channel.
‹ Press OK to mark (or unmark) the highlighted channel. The channel is added to (or removed from) the selected list.
≈Press the green key again to leave the Edit mode.
The modified channel list appears again.
Use more of your TV 25
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 26
5.7
Timers and locks
This section describes how to switch the TV on or off at a specified time and to lock or unlock the TV.
5.7.1
Automatically switch to standby
Sleeptimer switches the TV to standby after a time.
‡ Press Menu on the remote control and select
TV menu > Features > Sleeptimer and press navigation key right to enter the sleeptimer bar.
® Press navigation key up or down to set the time up to 180 minutes in steps of 5 minutes. If set to 0 minutes, the Sleeptimer is switched off.
You can always switch off your TV earlier or reset the time during countdown.
5.7.2
Automatically switch the TV on
Not applicable in case of no Teletext present.
On timer switches the TV on automatically to a specified channel at a specified time, from standby.
‡ Press Menu on the remote control and select
TV menu > Features > On timer and press navigation key right to enter the On timer menu.
® Use navigation key left, right or up, down to select and enter the menu items one by one to set a channel, a day of the week or daily, and a star ting time.
Ò Press OK to confirm.
† Press Menu to quit the menu.
Did you forget your code ?
‡ Select Change code.
® Press navigation key right.
Ò Enter the overriding code 8-8-8-8.
† Enter a new personal code.
º Confirm your new entered code.
The previous code is erased and the new code is stored.
5.7.4
Activate or deactivate Child lock
If your code is set, you can lock all channels and devices, lock a specific channel or device, set a time after which all channels and devices are locked.
‡ Press Menu on the remote control and select
TV menu > Features > Child lock and press navigation key right to enter your code.
® Enter your code with the number keys.
Ò Select one of the options.
† Press navigation key right.
Lock or unlock all channels and connected devices
‡ Select Lock or Unlock.
® Press OK .
Lock a certain programme or all channels from a certain time
Child lock
Lock
Custom lock
Unlock
Custom lock
Lock after
Channel lock
à Tip
To switch off the On timer, select Off in the On timer menu.
5.7.3
Lock TV channels and programmes
Lock TV channels and/or programmes from connected devices to prevent children from watching them. Lock and unlock with a four number code.
Set or change your code
‡ Press Menu on the remote control and select
TV menu > Features > Set or Change code and press navigation key right to enter your code.
® Enter your code with the number keys.
The Features menu reappears with a message confirming that your code has been created or changed.
‡ Select Custom lock.
® Press navigation key right to enter the Custom lock menu.
Ò Press navigation key right again to enter the
Lock after menu.
† Select On to switch on the Timer lock.
º Press navigation key left.
◊Select Time.
‹ Press navigation key right.
≈Enter the time with navigation key up or down and right.
Ú Press OK .
26 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 27
Lock one or more channels and connected devices
‡ Select Custom lock.
® Press navigation key right to enter.
Ò Press navigation key up or down to select
Channel lock.
† Press navigation key right.
º Press navigation key up or down to select the channel(s) you want to lock or unlock.
◊Each time press OK to lock or unlock the channel.
5.8
Subtitles
For each TV channel, subtitles can be set, coming from Teletext.
5.8.1
Subtitling from TV channels
‡ Select a TV channel.
® Press b to switch on Teletext.
Ò Enter the three number pagenumber of the subtitle page.
† Press b to switch off Teletext.
rNote
The Teletext subtitle page must be stored for each
TV channel separately.
5.8.2
Activate or deactivate subtitling
‡ Press Menu on the remote control and select
TV menu > Features > Subtitle and press navigation key right to enter the list.
TV menu
TV settings
Features
Installation
Software update
Features
Subtitle
Sleeptimer
Child lock
Set/Change code
On timer
Demo
® Press navigation key up or down to select On to show the subtitles always or On during mute to show the subtitles only when the sound is muted with the ¬ key on the remote control.
Ò Press navigation key left to return to the
Features menu.
à Tip
Select the Subtitle menu directly with Option on the remote control. See section 5.2.3 Quick access menu.
Use more of your TV 27
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 28
5.9
View and play: photos,
MP3, ...
Watch pictures or listen to music stored on a USB device (not supplied with the TV). Watch your pictures as a slideshow or listen to a self made music playlist.
rNote
Philips can not be held responsible if your USB device is not suppor ted nor shall Philips accept any liability for damage or loss of stored data.
® Press navigation key right to enter the Picture folder.
Ò Press navigation key up or navigation key down to select a picture or a picture album on the
USB device.
Picture
Afrika_2001
Paris_2005
My_car.jpg
Jean.jpg
Mary.jpg
Afrika_2001
Kenya.jpg
Congo.jpg
Victoria.jpg
Cairo.jpg
5.9.1
Insert a USB device
Inser t a device at the side of the TV while the TV is switched on.
The main menu appears automatically and the name of the USB device is highlighted next to
Multimedia.
Television
Multimedia
5.9.2
TV menu
Channel list
Remove the USB device
ç Caution
To avoid damaging the USB device always quit the menu on screen and wait five seconds before you remove the USB device.
‡ Press Menu to quit the menu.
® Remove the USB device.
Afrika_2001
Kenya.jpg
Congo.jpg
Victoria.jpg
Dakar.jpg
Cairo.jpg
Afrika_2001
Kenya.jpg
† Press OK to view the picture or to star t a slideshow of the pictures in the album.
º Press OK to pause the slideshow. Press again to restar t.
◊Press one of the colour keys on the remote control to perform the corresponding function shown at the bottom of the screen.
Press the blue key to stop the show and to see more functions.
If the function bar at the bottom disappeared, press any colour key to let it reappear.
‹ Press navigation key left and select another picture or another album.
5.9.3
View your pictures
The Multimedia menu shows the files you have stored on your USB device.
‡ Press navigation key right to enter the
Multimedia menu.
Picture is highlighted.
USB
Picture
Music
Picture
Afrika_2001
Paris_2006
My_car.jpg
Jean.jpg
Mary.jpg
Slideshow settings
• Details / More details
Shows the picture name, date, size and next picture in the slideshow.
• Transitions
Shows the list of available transition styles of the pictures.
Press navigation key up or down to select and press OK to activate.
• Slide time
Sets the time lag for the picture transitions:
Shor t, Medium or Long.
• Rotate
To rotate a picture.
• Zoom
Show a list of available zoom magnifications to select.
• Start/Show
To stop and restar t the slideshow.
28 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 29
5.9.4
Thumbnails
View the pictures of a selected album in an overview.
‡ Select a picture album.
® Press navigation key right to enter the picture list.
Ò Press the green key.
† Press navigation key up or down, left or right to highlight a picture.
º Press OK to view the picture.
◊Press navigation key left to return to the thumbnail overview.
‹ Press the green key again to go back to the picture list.
5.9.6
Slideshow with background music
Watch a slideshow of your stored pictures accompanied with your stored background music.
‡ Select an album of songs first and press OK .
® Highlight the Picture folder and select an album of pictures and press OK .
USB Afrika_2001 Kenya.jpg
Kenya.jpg
5.9.5
Listen to music
Find your songs in the Music album of the
Multimedia menu.
‡ Highlight Music in the Multimedia menu.
® Press navigation key right to enter the Music folder.
Ò Press navigation key up or down to select a song or a music album.
† Press OK to play the selected song or to play a song followed by the next song in the same album.
Music settings
• Details
Shows the file name.
• Repeat one/all
Repeat all songs in the album until you stop a song or only repeat the one song selected until you stop the song.
• Shuffle
Play songs in a random sequence.
Use more of your TV 29
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 30
5.10 Software update
Philips continuously tries to improve its products. It may be recommended for you to update the TV’s software. To update your TV software you need a
USB Memory device (not supplied).
rNote
The device must have at least 48Mb free space.
Make sure the write protection is turned off.
Some USB devices do not work with our TV.
Contact your dealer.
5.10.2 Software download from the PC to the USB device
‡ Insert the USB memory device into a PC linked to the internet.
® Locate and open the file “update.htm” on your
USB device.
Ò Read the instructions on screen and click on the Send ID button.
The software update is downloaded on the
USB memory device.
† Remove the USB memory device from your
PC.
5.10.1 Update assistant
The Update assistant helps you to update the TV’s software.
TV identification
The TV will identify itself to your USB memory device.
‡ Press Menu.
® Press navigation key right.
Ò Press navigation key up or down to select
Software update.
† Press navigation key right.
TV menu
TV settings
Features
Installation
Software update
Update assistant
Update assistant
Current software...
Local updates
5.10.3 Transfer of the downloaded software update to the TV
The downloaded software on the USB memory device must now be uploaded to your TV.
ç Caution
• Do not remove the USB memory device during the software update.
• If a power drop occurs during the update, do not remove the USB memory device from the TV.
The TV will continue the update as soon as the power comes back.
‡ Insert the USB memory device to the USB connector at the side of the TV.
º Press navigation key up or down to select
Update assistant.
◊Press navigation key right.
‹Press OK to activate.
≈Insert a USB memory device to the USB connector at the side of the TV.
The main menu appears.
Ú Press the green key to proceed.
A message appears the TV has successfully written the identification file to the USB memory device.
œ Press the green key again to finish.
π Remove the USB memory device from the TV.
U S B
® The TV switches off. The screen stays black for about 10 seconds. Wait and do not use the power switch B on the TV.
U S B
30 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 31
Ò The update process starts automatically. Please wait.
◊The TV switches off.The screen stays black for about 10 seconds. Please, wait.
U S B
The update is finished when the message
‘Operation successful’ appears on the screen.
‹The TV switches back on again.The update is done.
Pr g
Operation Successful! Re
U S B
† Remove the USB memory device from the TV.
U S B
º Press B on the remote control.
5.10.4
Verify the current software version
Updating software is only possible if the version of the new available software is different from the current one.You can verify your current software version.
‡ Select Software update in the TV menu.
® Press navigation key right.
Ò Press navigation key up or down to select
Current software info.
The version and the description of the current software appears.
B
B
INPUT v
TV DVD STB HTS rNote
Do not press more than once and do not use the
Power B switch on the TV.
Use more of your TV 31
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 32
6 Channel installation
The first time you switched on your TV you’ve selected the language of the TV menus and all the available channels have been installed.
This chapter will help you if you find it necessary to re-do the initial installation or if you want to tune in a new TV channel.
Ò Press navigation key right to select Start now.
† Press OK .
º Press the green key to start.
The installation may take a few minutes.
◊When the channel search is completed, press the red key to return to the Installation menu.
‹ Press Menu to quit the TV menu.
If you want to rename, reorder or uninstall stored channels, see section 6.3 Rearrange channels.
rNotes:
- You do not have to follow every step described if it is not necessary.
- Re-installation will modify the All channels list and new added channels will not be added to any favourite list.
6.2 Manual installation
You can tune-in TV channels channel by channel manually with Manual installation.
6.1
Automatic installation
This section describes how to search for and store all available channels automatically.
Step 1 Menu language
Sets the language of the TV menus. Go to a next step if your language settings are correct.
‡ Press Menu on the remote control and select
TV menu > Installation > Language.
® Press navigation key right to enter the menu
Language.
Ò Press navigation key up or down to select your language.
† Press OK to confirm.
º Press navigation key left to return to the
Installation menu.
Installation
Language
Channel install...
Preferences
Connections
Factory settings
Language
English
Français
Step 2 Install TV channels
Your TV will search for and store all available TV channels.
‡ Press navigation key down to select Channel installation.
® Press navigation key right to enter the Channel installation menu.
Automatic installation is highlighted.
6.2.1
Select the system
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Manual installation.
® Press navigation key right to enter the Manual installation menu.
System is highlighted.
Ò Press navigation key right to enter the System list.
† Press navigation key up or down to select your
TV system: PAL BG, PAL I, PAL DK or NTSC M.
º Press navigation key left to return to the
Manual installation menu.
Channel install...
Manual installation
Automatic install...
Manual installation
Rearrange
System
Search
Fine tune
Store current ch...
Store as new ch...
6.2.2
Search for and store a new channel
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Manual installation > Search.
® Press navigation key right to enter the Search menu.
Ò Press the red key to enter the frequency yourself or press the green key to search for a next channel.
32 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 33
à Tip
If you know the frequency, enter the three numbers of the frequency with the number keys of the remote control.
† Press navigation key left when the new channel has been found.
º Select Store as new channel to store the new channel under a new channel number.
◊Press navigation key right to enter.
‹ Press OK .
Done appears.
≈Press Menu to quit the channel installation menu.
º Press navigation key left or right to select a character or navigation key up or down to change the characters. Space, numbers and other special characters are located between z and A.
◊Press the green key or OK to finish.
à Tip
With the yellow key all characters can be deleted.
With the blue key you can delete the character which is highlighted.
6.2.3
Fine tune a channel
Fine tune a found channel when the reception is poor.
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Analogue: manual installation > Fine tune.
® Press navigation key right to enter the Fine tune menu.
Ò Press navigation key up or down to adjust the frequency
† Press navigation key left when you finished fine tuning.
º Select Store current channel to store the fine tuned channel under the current channel number.
◊Press navigation key right to enter.
‹ Press OK .
Done appears.
≈Press Menu to quit the Channel installation menu.
6.3
channels.
Rearrange stored channels
To rename, reorder, uninstall or reinstall stored
6.3.1
Rename a channel
Assign or change a channel name to a channel for which a name has not yet been entered.
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Rearrange.
® Press navigation key right to enter the channel list.
Ò Press navigation key up or down in the channel list to select the channel you want to rename.
† Press the red key.
6.3.2
Uninstall or reinstall a channel
To uninstall a stored channel so that it is no longer possible to tune to.
Reinstall an earlier uninstalled channel.
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Rearrange.
® Press navigation key right to enter the channel list.
Ò Press navigation key up or down in the channel list to select the channel you want to uninstall or reinstall.
† Press the green key to uninstall or reinstall the channel.
º Press Menu to quit the menu.
6.3.3
Reorder the channels
Change the order of the stored channels.
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Rearrange.
® Press navigation key right to enter the channel list.
Ò Press navigation key up or down in the channel list to select the channel you want to reorder.
† Press the yellow key to move up the highlighted channel in your channel list.
º Press the blue key to move down the highlighted channel in your channel list.
◊Press Menu to quit the menu.
Use more of your TV 33
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 34
6.4
Automatic channel management
Once a day, at 3 AM, all available TV channels are updated automatically. The update is done if your
TV is in standby.
Earlier stored channels not found by the update will be removed from the channel list.
You can do this update yourself anytime.
‡ Press Menu on the remote control and select
TV menu > Installation > Channel installation >
Installation update.
® Press navigation key right to enter the
Installation update menu.
Ò Press OK .
† Press the green key to start.
The update star ts and may take a few minutes.
º When the update is completed, press the red key to return to the Channel installation menu.
◊Press Menu to quit the menu.
6.5
Factory settings
If you are lost in the picture, sound and Ambilight settings, you can reset the TV to the factory settings of picture, sound and Ambilight
‡ Press Menu on the remote control and select
TV menu > Installation > Factory settings.
® Press navigation key right to enter the Factory settings menu.
Ò Press OK .
† Press Menu to quit the menu.
rNote
The channel installation settings are not changed.
34 Use more of your TV
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 35
7 Connections
7.1
Connection overview
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
1
2
3
4 5 6 7 8 9
MONITOR
OUT
L
R
AUDIO
OUT
DISPLAY
SYNC.
DISPLAY
SYNC.
OUT L
IN
DIGITAL
AUDI O
+
AV 2 HDMI 2
AV 3 HDMI 3
R
ANALOG
AUDIO IN
+
HDMI 1
HDMI 2
HDMI 3
HDMI 1
10 11
HDMI 2 HDMI 3 SERVICE
UART ANTENNA
16
17
12
13
14
15
USB
R
AUDIO
L
VIDEO
S-VIDEO
Back connectors
1 AV3
AV connector for DVD,VCR, digital receiver, game console, etc.
2 AV2
Second AV connector.
3 AV1
Component Video Y Pb Pr and Audio L/R connectors for DVD, digital receiver or game console, etc.
4 Monitor Out
Output connector for daisy chaining or to record programmes from your TV.
5 Audio Out L/R
Sound output cinch connectors for a Home
Theatre System, etc.
6 Digital Audio In (if present)
Sound input cinch connector for use with any of the HDMI connectors with a HDMI to DVI adaptor.
7 Digital Audio Out
Sound output cinch connector for a Home
Theatre System, etc.
8 Analog Audio In
Sound input cinch connectors for use with any of the HDMI connectors with a HDMI to DVI adaptor.
9 HDMI 1 In
HDMI in connector for Blu-ray Disc player, HD digital receiver or HD game console, etc.
10 HDMI 2 In
Second HDMI in connector.
11 HDMI 3 In
Third HDMI in connector.
12 Antenna input
Side connectors
13 USB
USB connector.
14 Headphones
Stereo Mini Jack.
15 Audio L/R in
Audio L/R for camcorder, game console, etc.
16 Video
Video input cinch connector to be used together with Audio L/R connectors for camcorder, game console, etc.
17 S-Video
S-Video input connector to be used together with Audio L/R connectors for camcorder, game console, etc.
Connections 35
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 36
7.2
About connecting
Learn here how to make the best connection for your device.
Six connections are ready to use at the back of the
TV - AV1, AV2, AV3, HDMI1, HDMI2 and HDMI3.
Connect your device with the highest possible quality connection. Look for the highest quality connection on your device. Use that connection to your TV.
Connection set up
When connecting is done the TV needs to know what connections you made, which device is connected to which connector. Use the TV menu to do this. See section 7.4 Connection set up.
7.2.2
HDMI-control (if present)
HDMI with Consumer Electronics Control (CEC) adds to the normal HDMI advantages. It offers easy operation of the TV and connected devices. These devices also have to be equipped with HDMI with
CEC.
‡ Press Menu on the remote control and select
TV menu > Installation > Preferences and press navigation key right to enter the list.
® Press navigation key up or down to select
HDMI-control.
ÒPress navigation key right to enter.
† Select On to activate HDMI with CEC.
rNote
HDMI-control might not work with other brands.
7.2.1
HDMI - Highest quality ★★★★★
A HDMI connection has the best picture and sound quality. One cable combines video and audio signals.
Use HDMI for HD (High Definition) TV signals.
HDMI can offer easy operation of your devices by the touch of one button when these devices have
HDMI with CEC.A device connected with HDMI to the TV can only send out audio and video signals to your TV. The device cannot receive or record audio and video from your TV.
One touch play
Inser t a DVD disc to watch and your TV will switch on from standby and show the DVD programme automatically when you star t playing the disc.
‡ Press Play π on the device.
The TV is switched on from standby.
System standby
Switches off all devices with the TV remote control.
‡ Press B on the TV remote control for a few seconds.
All devices will switch to standby.
7.2.3
YPbPr - Higher quality
★★★★
Use the Component Video YPbPr connections together with the Audio L/R mini jack. Match the cable colours when you connect.
YPbPr can handle HD TV signals.
HDMI cable (max. 5m)
à Tip
Use a HDMI / DVI adaptor in case your device has only a DVI connection. An extra audio cable is needed to complete this connection.
rNote
HDMI suppor ts HDCP (High-bandwidth Digital
Contents Protection). HDCP is a copy protection signal that comes with HD content (DVD disc or
Blu-ray Disc).
Component Video
YPbPr cable
- Red, Green, Blue
Audio L/R to Stereo mini jack cable
36 Connections
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 37
7.2.4
S-Video - Good quality ★★
Use a S-Video cable together with an Audio L/R
(cinch) cable. Match the cable colours when you connect.
An S-Video cable Audio L/R cable
- Red, White
7.2.5
Video - Basic quality
★
Use a Video (cinch) cable together with an Audio
L/R (cinch) cable. Match the cable colours when you connect
Combined Video - yellow and Audio L/R cable
- red and white
7.2.6
Display synchronised audio out
For the best match of image and sound in speech on screen, connect a Home Theatre System to
Audio Out L/R or Digital Audio outputs.
See diagrams 7.3.4 and 7.3.8.
Do not connect the audio signal of a DVD player, digital receiver or other audio/video device directly to the Home Theatre System.
Connections 37
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 38
7.3
Connect your devices
The connections shown in this section are recommendations for the most used cases.
Other solutions may be possible.
7.3.1
DVD player
Use a YPbPr cable and an audio L and R (cinch) cable to connect the device to the AV1 or AV3 input at the back of the TV.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
AV1/AV3
YPbPr
AV1/AV3
AUDIO L + R
7.3.2
DVD Recorder or Digital Receiver
Use a YPbPr cable and an audio L and R (cinch) cable and 2 antenna cables.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
AV1/AV3
YPbPr
AV1/AV3
AUDIO L + R
7.3.3
DVD Recorder and Digital Receiver
Use 3 YPbPr cables and 2 audio L and R (cinch) cables and 3 antenna cables.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
OUT
AV3 : YPbPr
AV3 : AUDIO L + R
AV1 : YPbPr
AV1 : AUDIO L/R
DVD Player
OUT
IN
DVD recorder / Digital receiver
IN OUT IN
DVD Recorder Receiver / Cable box
38 Connections
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 39
7.3.4
DVD Recorder and Home Theatre
System
Use a YPbPr cable and an audio L and R (cinch) cable, 2 antenna cables and 1 digital audio (cinch) cable.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
DIGITAL
AUDIO
OUT
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
AV1/AV3
YPbPr
AV1/AV3
AUDIO L/R
OUT IN
DIGITAL
AUDIO
IN
Home Theatre System
7.3.5
DVD Recorder and DVD Home
Theatre System
Use 2 YPbPr cables and 2 audio L and R (cinch) cables, 2 antenna cables and 1 digital audio (cinch) cable.
DVD Recorder
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
DIGITAL
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
AV1/AV3
YPbPr
AV1/AV3
AUDIO
L/R
DVD Recorder
DIGITAL
AUDIO
IN
OUT IN
Home Theatre System
Connections 39
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 40
7.3.6
Satellite receiver
Use a YPbPr cable and and audio L and R (cinch) cable and 2 antenna cables.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
AV1/AV3
YPbPr
AV1/AV3
AUDIO L + R
7.3.7
HD Digital receiver / HD satellite receiver
Use a HDMI cable and 2 antenna cables.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
AUDIO
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
Satellite receiver
OUT IN
HDMI
HD Digital receiver / HD Satellite receiver
7.3.8
DVD-R, Home Theatre System and
Digital receiver
Use 3 YPbPr cables and 3 audio L and R (cinch) cables, 3 antenna cables and 1 digital audio (cinch) cable.
AV3 : YPbPr
AV3 :
AUDIO
L/R
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
DIGITAL
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
YPbPr
AUDIO L/R
AV1 : YPbPr
AV1 : AUDIO L/R
OUT
DVD Recorder Digital Receiver
IN
DIGITAL
AUDIO
IN
OUT IN
Home Theatre System
40 Connections
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 41
7.3.9
Blu-ray Disc player
Use a HDMI cable.
L
AV 3
AUDIO
R
Y Pb Pr
VIDEO L AUDIO R
AV 2
VIDEO L AUDIO R
S-VIDEO
AV 1
Y Pb Pr
L
MONITOR
OUT
R
AUDIO
OUT
OUT
IN
DIGITAL
AUDIO
L
R
ANALOG
AUDIO IN
HDMI 1 HDMI 2 HDMI 3
ANTENNA
HDMI
Blu-ray Disc player
7.3.10 Game console
The most practical connection for a game console is at the side of the TV. More qualitative connections are at the back of the TV.
Connected at the side of the TV
Use the Video and Audio L/R (cinch) connectors.
Connected at the back of the TV
Use a HDMI or the YPbPr (AV1 or AV3) input for
HD quality.
7.3.11 Camcorder
The most practical connection for a camcorder is at the side of the TV. More qualitative connections are at the back of the TV.
Connected at the side of the TV
Use the Video and Audio L/R (cinch) connectors or use the S-Video and Audio L/R connectors.
Connected at the back of the TV
Use a HDMI or the YPbPr (AV1 or AV3) input for
HD quality.
R
AUDIO
L
VIDEO
S-VIDEO
R
AUDIO
L
VIDEO
S-VIDEO
R
AUDIO
L
VIDEO
S-VIDEO
Connections 41
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 42
7.3.12 Personal Computer
The best connection for a PC is at the back of the
TV. A more practical connection, but only for viewing photos and films from your PC, is the connection at the side of the TV.
ç Caution
Before connecting the PC, set the PC monitor refresh rate to 60Hz.
Connected at the back of the TV
Use the DVI connection of your PC to connect to a HDMI connection of the TV. Use a HDMI to DVI cable or a HDMI-to-DVI-adaptor.
Add an Audio L and R cable and connect it to
Audio L and R jacks of ANALOG AUDIO IN of the
TV.
ANALOG
AUDIO IN
HDMI
DVI
HDMI
DVI
AUDIO OUT
AUDIO
OUT
In the Connections menu, link this AUDIO IN L/R to the HDMI connector you are using.
See section 7.4 Connections setup.
Connected at the side of the TV
If your PC has no DVI connection, use the S-Video and Audio L/R (cinch) connectors at the side of the
TV. This connection is only suited for applications like Windows Media Center or similar.
à Tip
Change the TV picture format to Unscaled in the
Picture format menu for maximal picture sharpness.
See section 5.3.4.Widescreen picture format.
For suppor ted PC monitor resolutions, see section
8 Technical data.
42 Connections
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 43
7.4
Connections setup
When all devices have been connected the TV needs to know what connections you have made, which device is connected to which connector.
7.4.1
Digital Audio In (if present)
If you use the Digital Audio In connection, assign this connection, in the menu, to the device from where the sound comes from.
‡ Press Menu on the remote control and select
TV menu > Installation > Connections > Digital
Audio In.
® Press navigation key right to enter the list.
Ò Press navigation key up or down to select the connector used by the device.
Connections DIGITAL AUDIO IN
...
AV 3
HDMI 1
HDMI 2
HDMI 3
Side
AUDIO IN L/R
DIGITAL AUDIO IN
None
AV 1
AV 2
AV 3
HDMI 1
HDMI 2
HDMI 3
Side
7.4.3
Naming your devices
Name the connected devices for easy selection and best signal handling.
Assign the type of device (DVD, VCR, Game ...) to the connector you use for that device.
‡ Press Menu on the remote control and select
TV menu > Installation > Connections > AV1 .
® Press navigation key right to enter the list.
Ò Press navigation key up or down to select the type of device.
† Press Menu to quit the menu.
Connections
AV 1
AV 2
AV 3
HDMI 1
HDMI 2
HDMI 3
Side
...
AV 1
None
DVD
Blu-ray
HDD/DVDR
HD rec.
Game
VCR
...
7.4.2
Audio In L/R
If you use the Audio In L/R connection, assign this connection, in the menu, to the device from where the sound comes from.
‡ Press Menu on the remote control and select
TV menu > Installation > Connections > Audio
In L/R.
® Press navigation key right to enter the list.
Ò Press navigation key up or down to select the connector used by the device.
Connections
...
AV 3
HDMI 1
HDMI 2
HDMI 3
Side
AUDIO IN L/R
AUDIO IN L/R
None
AV 3
HDMI 1
HDMI 2
HDMI 3
Connections 43
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 44
8 Technical data
Picture / Display
• Display type: LCD Full HD W-UXGA
• Panel resolution: 1920x1080p
• Perfect Pixel HD picture enhancement
• 1080p 24/25/30/50/60Hz processing
• 100 Hz Clear LCD
Supported display resolutions
• Computer formats
Resolution
640 x 480
800 x 600
1024 x 768
Refresh rate
60Hz
60Hz
60Hz
1280 x 768
1360 x 768
• Video formats
Resolution
480i
480p
576i
576p
720p
1080i
1080p
1080p
60Hz
60Hz
1920 x 1080i 60Hz
1920 x1080p 60Hz
Refresh rate
60Hz
60Hz
50Hz
50Hz
50Hz, 60Hz
50Hz, 60Hz
24Hz, 25Hz, 30Hz
50Hz, 60Hz
Sound
• Sound system:
- Vir tual Dolby Digital
- BBE
Multimedia
• Connection: USB
• Playback formats: MP3, LPCM, Slideshow (.alb)
JPEG
Remote control
• Type: RC4490
• Batteries: 3 Size AAA- LR03 type
Connectivity
• AV1: Audio L/R, CVBS in, YPbPr, S-Video
• AV2: Audio L/R, CVBS in
• AV3: YPbPr, Audio L/R in
• HDMI 1
• HDMI 2
• HDMI 3
• HDMI-control 1.3a
• Analog Audio L/R out - display synchronised
• Analog Audio L/R in
• Digital Audio in (coaxial-cinch-S/PDIF) (if present)
• Digital Audio out (coaxial-cinch-S/PDIF) display synchronised
• Monitor out
• Side: Audio L/R in, Video (CVBS) in, S-Video
Headphone out (stereo mini jack), USB
Tuner / Reception / Transmission
• Antenna input: 75ohm coaxial (IEC75)
• TV system: DVD COFDM 2K/8K
• Video playback: PAL BG; PAL I, PAL DK, NTSC M
Dimensions and weights (approx.)
Power
• Mains power : AC 220-240V (±10%)
• Power and standby power consumption:
See technical specification on www.philips.com
• Ambient temperature: 5°C - 35°C
TV model
- width
- height
- depth
- weight
TV + stand
- width
- height
- depth
- weight
42PFL9900/98
1121 mm
715 mm
130 mm
39,2 kg
1121 mm
810 mm
305 mm
48,5 kg
Specifications are subject to change without notice.
For more specification details of this product see www.philips.com/suppor t.
44 Technical data
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 45
TV channels
9 Troubleshooting
Television and remote control
Some TV channels are gone
• Verify if the correct channel list is chosen.
• A channel could be uninstalled in the Rearrange menu
The TV does not switch on
• Verify the mains cord connection.
• Verify if the batteries of the remote control are flat or weak. Verify their + / - orientation.
You can use the keys on the TV to switch the TV on.
• Unplug the mains cord, wait for one minute and plug in the mains again.
The TV does not react on the remote control
• Verify if the batteries of the remote control are not empty or weak. Verify their + / - orientation.
• Clean the remote control and TV sensor lens.
• Use the side control keys to change some of the basic settings of picture and sound.
‡ Press Volume - and + to adjust the volume.
® Press Program/Channel - and + to go through the channels marked as favourites.
Ò Press Menu to show the main menu.
Press Program/Channel - and + to select and adjust picture and sound menu items.
Picture
There is no picture
• Verify if the antenna is connected properly.
• Verify if the correct device is selected.
The sound is on, but there is no picture
• Verify the contrast or brightness setting in the menu.
The TV picture is poor
• Verify if the antenna is connected properly.
• Loudspeakers, non-ear thed audio devices, neon lights, high buildings or mountains can influence the picture quality. Try to improve the picture by changing the antenna direction or place devices away from the TV.
• Verify if the correct TV system is chosen in the
Manual installation menu.
• If only a cer tain channel is poor, try to fine tune this channel in the Fine tune menu. See section
6.2.3.
The red light on the TV blinks
• Unplug the mains cord for half a minute and inser t it again. Verify if there is enough space for ventilation. Wait until the TV has cooled down.
When the TV does not restar t to standby and the blinking occurs again, call our Customer
Suppor t Centre.
You forgot your code to unlock Child lock
• See section 5.8.3 Set code / Change code.
Wrong language in the TV menu ?
Follow these steps to change the language.
‡ Press Menu on the remote control.
® Press navigation key right.
Ò Use navigation down to highlight the third line.
† Press navigation key right three times.
º Press navigation key up or down to select your language.
◊Press OK .
‹Press Menu to quit the menus.
The picture has poor colour
• Verify the colour settings in the Picture menu.
Select any of the Reset to standard settings in the Reset to standard menu. See section 5.3.2.
• Verify the connections and cables of the connected devices.
The TV did not remember my settings when I switch back on
• Verify if the TV is set to Home in the TV menu >
Installation > Preferences > Location menu.
The picture does not fit the screen, it is too big or too small
• Select a more fitting picture format in the Picture format menu.
See section 5.3.4 Widescreen picture format.
• Name your connected device in the Connections menu to obtain the best signal handling.
See section 7.4.3 Naming your devices.
Troubleshooting 45
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 46
The picture position on screen is not correct
• Some picture signals from some devices do not fit the screen correctly. You can shift the picture with the navigation key on the remote control.
Check the signal output of the device.
Sound
There is a picture but no sound
• Verify the volume is not set to 0.
• Verify the sound has not been muted with the
¬ key.
• Verify if all cables are connected properly.
• If no sound signal is detected, the TV automatically switches off the sound.
This is proper operation and does not indicate malfunction.
The sound is poor
• Verify if the sound is set to Stereo.
• Verify the Equalizer settings.
• Select any of the Reset to standards settings in the Reset to standard menu. See section 5.3.2.
The sound comes from one speaker only
• Verify if the Balance is not set to extreme left or right.
HDMI connections
Trouble with devices connected with HDMI
• The HDMI - HDCP procedure might take a few seconds before the TV shows the picture from a device.
• If the TV does not recognise the device and the screen shows no picture, try switching from one device to another and back again to restar t the
HDCP procedure.
• If sound interruptions occur persistently, see the user manual of the device to verify the output settings. If that does not help, connect an additional audio cable.
• If an HDMI-to-DVI adaptor is used, verify if an additional audio connection is in place to complete the DVI connection.
USB connection
The TV does not show the USB device content
• Set your device (camera) to ‘Mass Storage Class’ compliant.
• The USB device may need specific driver software. Unfor tunately this software can not be downloaded to your TV.
I can not see my files in the Multimedia menu.
• Not all audio and picture files are suppor ted. See section 8 Technical data.
Audio and picture files do not playback smoothly
• The transfer performance of the USB device limits the transfer rate.
Personal computer
The PC display on my TV is not stable or is not synchronised
• Verify if the correct resolution mode is selected on your PC. See section 8 Technical data.
If your problem is not solved
Switch your TV off and on again. If the problem is not solved, call the Customer Suppor t Centre or consult our website www.philips.com/suppor t.
See the Customer Suppor t Centre telephone numbers on the last page of this user manual.
Please, have the TV Model and Product Number ready before you call.
You can find these numbers on the packaging label or on the typelabel on the back and bottom of the
TV.
) Warning
Never try to repair the TV yourself.
46 Troubleshooting
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 47
10 Index
100 Hz Clear LCD 20
A
Active Control 20
Ambilight menu / settings 23 modes 23
Antenna cable 9 connect 9 with devices 35
Auto format 21
Automatic installation 32
Auto surround 22
Automatic Volume Leveler 22
B
Balance sound 22
Batteries 3,9
Blacklevel 20
Blu-ray 36,41
Brightness 20 ambilight 23
C
Cable
HDMI 36
YPbPr 36
S-Video 37
Video 37
Camcorder 41
Camera (photo) 41
Care of the screen 3
Change code 26
Channel all channels list 25 favourite list 25 installation 33 lock 27 management 34 previous 14 rearrange 33
Channel store / install 32
Child lock 26
Clock 19
Code 26
Colour enhancement 20
Colour menu 20 keys 4,14
Connection best 36 overview 35 set up 38,43
Contrast 20
Custom lock 27
Custom tint 20
D
Delta volume 22
Device connecting 38 naming 43 watch 11
Digital audio out 37 receiver 38
Dual I/II 22
Dual screen 14
DVD connect 38 playback 11 player 38 recorder 38
Dynamic contrast 20
E
Equalizer 22
External 1,2,3 (AV) 35
F
Factory settings 34
Favourite channel lists 25
Fine tune 33
G
Game console 41
H
HDCP 36
HDMI connection 36
HD digital receiver 40
HD natural motion 20
Headphone connect 4,35 volume 22
Index
Home location 45
Home theatre system 39
Hue 20
I
Installation automatic 32 manual 32 menu 32 update 34
K
Kensington Security Slot 5
Key(s) colour 14 on TV 4 on remote control 4,14
L
Language menu 32
Locks 26
M
Mains cord 10
Menu key 17
Mono 22
Movie expand 21
MPEG ar tefact reduction 20
Music 29
Mute key 14
N
Naming devices 43
Noise reduction 20
O
OK key 14
On timer 26
P
Perfect Pixel HD 20
Personal Computer connect 42 display resolutions 44
Photo viewer 28
Picture format 20 menu 20
47
2664.1 eng_aurea_AP 27-09-2007 12:32 Pagina 48
Position the TV 5
Power 10
Programme up/down 14
Q
Quick access menu 19
R
Rearrange channels 33
Recorder 38
Recycling 3
Remote control batteries 9 overview 14
Rename 33
Reorder 33
Reset to standards 19
S
Safety 3
Satellite receiver 40
Screen cleaning 3
Search channels 32 teletext pages 23
Set code 26
Settings assistant 19
Sharpness 20
Sleeptimer 26
Software update 30
Sound menu 22 surround mode 22
Standby 14,26
Super zoom 21
Stationary images 3
Stereo 22
Subtitle 27 shift 21
Switch on 10
T
Technical data 44
Teletext 23 teletext 2.5 24 dual screen 23 menu 24 page 23
Timers 27
Tint 20
Troubleshooting 45
TV settings menu 17
U
USB connector 35 device 28 photo viewer 28
V
VCR connect 38
Video cable 37
Video formats 44
Volume key 14 menu 22
W
Whitepoint 20
Widescreen picture format 21
Y
YPbPr 36
48 Index
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project