Philips AZ1209 User's manual

Philips AZ1209 User's manual
PHILIPS
AZ 1209 CD Radio Cassette Recorder
~ ^^
= тео по ео и
SL
Instructions for use
Mode d’emploi
Instrucciones de manejo
Bedienungsanleitung
Gebruiksaanwijzing
Istruzioni per uso
Brugsanvisning
Bruksanvisning
Kayttoohje
Manual de utilizacáo
Oonyíec xpijoewc
PHILIPS
= = - + = ————— - -— — ————]]Í— —
Important notes for users in the U.K.
Mains plug
This apparatus 15 fitted with an approved 13 Amp plug.
To change a fuse in this type of plug proceed as follows:
1 Remaove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp,
A S.TA. or BS! approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted in its
place. If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse is used,
the fuse at the distribution board should not be greater
than 5 Amp.
Note: The severed plug must be disposed of to avoid a
possible shock hazard should it be inserted into a
13 Amp socket elsewhere
How to connect a plug
The vares in the mains lead are coloured with the
following code blue = neutral (N), brown = live (L) As
these colours may not correspond with the colour
markings identifymg the terminals in your plug,
proceed as follows:
* Connect the blue wire to the terminal marked N or
coloured black
e Connect the brown wire to the terminal marked L or
coloured red.
e Do not connect either wire to the earth terminal in
the plug, marked E (or 4) or coloured green (or green
and yellow).
Before replacing the plug cover, make certain that the
cord grip is clamped over the sheath of the lead - not
simply over the two vires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The Performer's
Protection Acts 1958 to 1972.
Norge
Typeskilt finnes pa apparatens underside.
Observer: Nettbryteren er sekundert innkoplet.
Den innebygde netdelen er derfor ikke frakoplet
nettet sa lenge apparatet er tilsluttet
nettkontakten.
For 4 redusere faren for brann eller elektrisk stat,
skal apparatet ikke utsettes for regn eller fuktighet.
Deutschland
Hiermit wird bescheinigt, daß dieses Gerät In
Übereinstimmung mit den Bestimmungen der
Amtsblattverfugung 1046/1984 funkentstört Ist.
Der Deutschen Bundespost wurde das
Inverkehrbringen dieses Gerates angezeigt und die
Berechtigung zur Überprüfung der Serie auf
Einhaltung der Bestimmungen eingeraumt
Italia
DICHIARAZIONE Di CONFORMITA
S1 dichiara che l’apparecchio Lettore CD/Radio-
registratore mod. AZ1203 Philips risponde alle
prescrizioni dell'art. Z comma 1 del D. M. 28 Agosto
1995 n. 548.
Fatto a Eindhoven, il 22/07/1997
Philips Sound & Vision
Philips, Glaslaan 2, SFF 19
5616 JB Eindhoven, The Netherlands
É, - Сопго!$ „...енсненноннононнноннннея 4-5 CD player ..........e.ee.————. 9-11
Engl ish Power supply res 6 Cassette recorder .......... 12-13 Ка
Basic functions ..............—...... 7 General information............. 14 =
\_ Radio 8 Troubleshooting ................... 15
@ . Comandes............—........ 16-17 Lecteur de CD................ 21-23 ©
Fran ca IS Alimentation .............—.. 18 Platine cassette............. 24-25 s
Fonctions de base................ 19 Informations général ........... 26 =
O Radio 20 Recherche de pannes.......... 27 =
( - Controles …………………… 28-29 Reproductor CD ............. 33-35 =
Español Fuente de alimentación .......30 Grabadora.................... 36-37 =
Funciones Dásicas................ 31 Información general............. 38 2
\_ Radio 32 Localización de averias .......39
(, Bedienungselemente.....40—41 CD-Spieler ......... 45-47 =
Deutsch Stromversorgung .............. 42 Kassetterecorder ........... 48-49 2
Grundfunktionen .................. 43 — Allgemeine Informationen...59 2
\_ Radio .......—. nene 44 — Fehlerbehebung................... 51
( Bedieningstoetsen......... 52-53 Cd-speler ere 57-59 =
Nederlands Voeding 54 Cassetterecorder …… 60-61 =
Basisfuncties …………….….….… 55 Algemene informatie 62 =
« Radio 56 Problemen oplossen...........- 63 =
(eue Comandi……….…….……--0…- 64-65 | Lettore CD... 69-71 >
Italiano Alimentazione ................. 66 Registratore...........—. 72-73 =
Funzioni principali................ 67 Informazioni generale.......... 74 ©
« Radio 68 Ricerca guasti.........—...———... 75 a
/, Kontroller.......——————. 76-77 CD-spelare.................... 81-83 <
Svenska Stromfársórining............... 78 Kassettspelare,............ 84-85 %
Basfunktioner..............—.. 79 Allmän information.............. 86 ©
« Radio 80 Felsókning.............———e.—. 87 ©
Betjeningsorganer ......... 88-89 CD-afspiller.............. 93-95
Dansk Stromforsyning .............- 90 Kassettebandoptager ....96-97 %
Grundfunktioner.............—..... 91 Generel information............. 98 a
Radio 92 Fejlfinding 99
@ - Saado anne 100-101 CD-soition……………. 105-107 _
Suomi Virtaláhde ............e=e=..... 102 Kasettinauhuri........... 108-109 E
Perustoiminnot............—. 103 Yleistietoja..........— wm... 110 a
O Radio 104 Vianetsintá........—— 111
й a Comandos.........o.... 112-113 Leitor CD... 117-119 æ
Portug ues Alimentacáo............—..—.... 114 Gravador de cassetes..120-121 >
Funcöes bäsiCaS................. 115 Informacdes gerais............ 122 =
\_ Radio... 116 Localizagdo der avarias .....123 a
( < O8nytec ХрПотс........ 124-125 Фортто СО................ 129-131 ча
EAANVIKG TPogpodoacía...................... 126 — Kagetéewvo 132-133 >
Badikéc Asttoupyieg ........ 127 | Evikée TAnpogopies 134 =
9 Pañió 128 Aveúpeon poSMuátwY ..135
CONTROLS
English
CONTROLS
BASIC FUNCTIONS
(1) POWER:
CD, TUNER, TAPE...selects the sound source
(2) INCREDIBLE
SURROUND. .......... creates a phenomenal
stereo effect
(3) DBB.........—..———.mm.m... enhances the bass
(3) VOLUME Y A......adjusts the volume level
6) 3.5mm headphone socket
Note: Connecting the headphones will switch
off the speakers.
(6) Display
(7) REMOTE SENSOR..sensor for the infrared
remote control
CD PLAYER
A OPEN vers opens the CD
compartment
STOP 1... stops CD play and erases
the program
PLAY-PAUSE D{0...starts and interrupts CD
play
SEARCH wa ppi.....skips and searches
forward and backward
PROGRAM ............ programs track numbers
and reviews the program
SHUFFLE ............... plays CD tracks in random
order
REPEAT ................. repeats a track, the entire
CD, or the program
(9) RADIO
SEARCH ra pra .....tunes to radio stations
BAND.......—em.necoos selects the wave band
PROGRAM ............ programs radio preset
stations
PRESET A Y .......selects a radio preset
station
CASSETTE RECORDER
PAUSE ID..........—.... interrupts recording or
playback
STOP-OPEN CJA ...stops the tape and opens
the cassette compartment
SEARCH > ........... rewinds the tape
SEARCH «............ fast forwards the tape
PLAY <l......me—cnmnon.e starts playback
RECORD O............ starts recording
REMOTE CONTROL
VOLUME ¥ A ..... decreases or increases the
volume level
SHUFFLE ..........—.—.. plays CD tracks in random
order
REPEAT ...........—..e.. repeats a track, the entire
CD or the program
| starts and interrupts CD
play
FOD............—..——— selects the beginning of
the current, a previous or a
subsequent track of a CD
N stops CD play and erases
the program
SEARCH << »».....searches backward/forward
in a CD track
PRESET A ¥ .......selects a radio preset
station
TUNING re »» .....tunes to radio stations
English
POWER SUPPLY
ys! Buy
Batteries
For the set (optional)
Open the battery compartment of the set and insert 6 batteries,
type R20, UM-1 or D-cells (preferably alkaline).
For the remote control (supplied)
Open the battery compartment of the remote control and insert ?
batteries, type R03, UM-4 or AAA-cells (preferably alkaline).
—
ji+ +
JR
Remove batteries if they are flat or the set is not going to be used
for a longer period of time.
Batteries contain chemical substances, so they should be
disposed of properly.
Mains
1 Check whether the mains voltage as shown on the type plate
corresponds to your local mains voltage. If it does not, consult
your dealer or service organisation. The type plate is located
on the bottom side of the set.
2 If the set is equipped with a VOLTAGE selector C0, set this
selector to the local mains voltage.
3 Connect the mains cable to the AC MAINS inlet and the wall
socket. This switches on the mains supply. The mains cable is
inside the battery compartment.
The battery supply will be switched off when the set is connected
to the mains. To change over to battery supply, pull out the plug
from the unit's AC MAINS socket.
To disconnect the set from the mains completely, remove the mains
plug from the wall socket.
For users in the U.K: please follow the instructions on page 2.
Environmental information
and polyethylene (bags, protective foam sheet).
batteries and old equipment
All redundant packing material has been omitted. We have done our utmost to make the
packaging easily separable into three mono materials: cardboard (box), polystyrene faam (buffer)
Your set consists of matenals which can be recycled if disassembled by a specialized company.
Please observe the local regulations regarding the disposal of packing materials, exhausted
-
6
——
BASIC FUNCTIONS
¡Switching on and off
Set the POWER slider to the desired sound source:
CD, TUNER, or TAPE.
The set is switched off when the POWER slider is in position
OFF/TAPE and the keys of the tape deck are released.
Note: If you run the set on batteries, always be sure to switch the |"
set off after use. This will avoid unnecessary power
consumption.
Adjusting volume and sound
Adjust the volume using the VOLUME Y A control.
— Display indication: Volume level from 0 to 32.
Increase and decrease the bass level by pressing DBB.
Switch the surround sound effect on and off by pressing
INCREDIBLE SURROUND.
The bass level can also be emphasised if you place the set against
a wall or shelf. Do not cover any vents and leave sufficient room
around the unit for ventilation.
Note: The effect of INCREDIBLE SURROUND may vary with
different types of music.
Improving radio reception
For FM stations, pull out the telescopic antenna. To improve the
signal, incline and turn the antenna. Reduce its length if the signal
is too strong (very close to a transmitter).
For MW and LW stations, direct the built-in antenna by turning the
whole set. The telescopic antenna is not needed.
English
RADIO
ysijbug
Tuning to radio stations
1 Set the POWER slider to TUNER.
2 Select the wave band by using the BAND selector.
— Display indication: the selected waveband.
3 Press SEARCH ww or bi for approx. 1 second and then release
the button.
— The radio automatically tunes to a station with sufficient
strength. Display indication during automatic tuning: 5- = À.
4 Repeat this procedure until you find a station you desire.
To tune to a weak transmitter briefly press SEARCH 144 or bi as
often as necessary for optimum reception, or until the correct
frequency is indicated in the display.
TUNER EM
Programming radio stations (29 preset stations)
You can store up to 29 radio stations in the memory. When
tuning to a preset station, the preset number (1 to 29) is indicated |
in the display.
1 Set the POWER slider to TUNER.
2 Press PROGRAM to enter the programming mode.
— During programming, PROGRAM flashes on the display.
3 Tune to a desired station with SEARCH «or bei, as described
earlier (see “Tuning to radio stations”).
— If the frequency is already stored in the memory, the preset
number will be displayed.
4 Press PRESET ¥ or A to allocate a number from 1 to 29 to the
preset station.
5 Press PROGRAM to confirm the setting.
Tuning to preset stations
Press PRESET V or A until the desired preset number appears +
on the display. C mn an
IL IL
FM
CD PLAYER
Playing a CD |
1 Set the POWER slider to CD. TS J J
NA TN [
2 Press À OPEN to open the CD compartment. = / 7
La _
pee 7 —
3 Insert an audio CD (printed side up) and close the CD ==
compartment.
— The CD player starts and scans the contents list of the CD. Г
Then, the CD player stops. Display indication: the total IZ чп.
number of tracks and the total playing time of the CD. Sra LIO
4 Press the PLAY-PAUSE D>11 button to start CD play.
— Display indication: the current track number.
5 Press the STOP OJ button to stop CD play.
— Display indication: the total number of tracks.
You can interrupt CD play by pressing PLAY-PAUSE P00. Continue Y ZT /
CD play by pressing the button again.
— Display indication: the time of the actual position flashes.
Note: CD play will also stop if:
— you open the CD compartment,
— the end of the CD is reached, or
— you move the POWER slider to TUNER or TAPE.
If you make a mistake when operating the CD player, or the 1
CD player cannot read the CD, the display shows à # £-7.(See LO Г
chapter "TROUBLESHOOTING”.) Eta EC”
If you press PLAY-PAUSE D>11 and there is no CD inserted the
display shows ne & (52. nao NIC
Cra LI 1 JL
English
CD PLAYER
yst6u3
Different playing modes: SHUFFLE / REPEAT
SHUFFLE — Playing in random order
1 Press SHUFFLE before or during CD play.
— All the tracks of the CD (or program if available) will now be
played in random order.
2 Press SHUFFLE again to return to normal CD play.
REPEAT — Repeating the entire CD or one track of the CD
1 Before or during CD play, press REPEAT repeatedly to cause the
display to show the different repeating modes.
— REPEAT: the current track is played repeatedly.
— REPEAT ALL: the entire CD or program is played repeatedly.
2 Press REPEAT until the display indication disappears to return to
normal CD play.
Note: You can activate the different playing modes at the same
time, e. g. you can repeatedly play the entire CD or program
in random order (SHUFFLE REPEAT ALL).
SHUFFLE
REPEAT ALL
Li.
Search backward << and forward >>
Selecting another track
Briefly press the SEARCH wa or >i button once/several times to
skip to the beginning of the current/previous or subsequent
track(s).
During play:
CD play continues automatically with the selected track.
When CD playback is stopped:
Press PLAY-PAUSE D>10 to start CD play.
— Display indication: the selected track number.
Searching for a passage during CD play
1 Hold down the SEARCH i or ei button to find a particular
passage in a forward or backward direction.
— CD play continues at a low volume.
2 Release the button when you have reached the desired passage.
Note: In the SHUFFLE and REPEAT modes or when playing a program,
searching is only possible within the particular track.
10
CD PLAYER
Programming track numbers |
You can select a number of tracks and store these in the memory
in the desired sequence. You can store any track more than once.
A maximum of 20 tracks can be stored in the memory.
1 Select the desired track with SEARCH 144 or bol
2 As soon as the number of the desired track is displayed, press À sem À
the PROGRAM button to store the track in the memory.
— PROGRAM appears in the display and the number of the [Proce
stored track is shown. Then jz = i lights up briefly. aran
Cr Г ou
3 Select and store all desired tracks in this way.
You can review your settings by pressing the PROGRAM button
for more than 2 seconds.
— The display shows all stored track numbers in sequence.
If you try to store more than 20 tracks the display shows # &fà £ . PROGRAM
E
Cra | LILL
If you press PROGRAM and there is no track selected, the display
shows mm SEL.
me CC
Cam LLL
Playing the program |
If you have selected the tracks in the stop position, press [recon
PLAY-PAUSE D0. = =r
| | Cea LI PAL
If you have selected the tracks during CD play, first press STOP CJ,
then press PLAY-PAUSE Din.
Erasing the program when CD playback is stopped |
From the stop position, press STOP Cl.
— ns pres lights up briefly, PROGRAM disappears and your nn
program is erased. Era - PE Ll
Note: The program will also be erased if you
— interrupt the power supply,
— open the CD compartment, or
— move the POWER slider to TUNER or TAPE.
11
English
CASSETTE RECORDER
ys Bu
Playing a cassette
1 Set the POWER slider to TAPE.
2 Press STOP-OPEN OA to open the cassette compartment.
3 Insert a recorded cassette with the open side upwards and close
the cassette compartment.
4 Press PLAY < to start playback.
5 Press >> or << to rewind or fast forward the tape.
6 To stop the tape press STOP-OPEN DA.
Note: The keys are released at the end of the tape.
General information on recording
Recording is permissible insofar as copyright or other rights of
third parties are not infringed upon.
For recording on this set you should use a cassette of the type
NORMAL (IEC type I). This deck is not suitable for recording on
cassettes of the type CHROME (IEC type II) or METAL (IEC
type IV).
The recording level is set automatically. The controls VOLUME,
INCREDIBLE SURROUND and DBB do not affect the recording.
At the very beginning and end of the tape, no recording will take
place in the 7 seconds during which the leader tape passes the
recorder heads.
Protecting tapes from accidental erasure
Keep the cassette side to be protected in front of you and snap off
the left tab. Now, recording on this side is no longer possible.
To record again on this side of the cassette, cover the aperture
with a piece of adhesive tape.
12
CASSETTE RECORDER
Recording from the CD player — CD synchro start
1 Set the POWER slider to CD.
2 Insert a CD and, if desired, program track numbers.
3 Press STOP-OPEN CIA to open the cassette compartment.
4 Insert a blank, unprotected cassette and close the cassette
compartment.
5 Press RECORD O to start recording.
— Playing of the CD or program starts automatically. It is not
necessary to start the CD player separately.
6 For brief interruptions press PAUSE Di. Press the PAUSE 11 key
again to resume recording.
7 To stop recording, press STOP-OPEN OA.
Note: the recording can be started from different positions:
— if the CD player is in pause mode, recording will start
from this very position (use SEARCH Ka orb»i);
— if the CD player is in stop mode, recording will start from
the beginning of the CD or program.
Recording from the radio
1 Set the POWER slider to TUNER.
2 Tune to the desired radio station (see chapter “RADIO”).
3 Press STOP-OPEN CIA to open the cassette compartment.
4 Insert a blank, unprotected cassette and close the cassette
compartment.
5 Press RECORD O to start recording.
6 For brief interruptions press PAUSE 00. To resume recording press
the PAUSE 00 key again.
1 To stop recording, press STOP-OPEN CA.
13
English
GENERAL INFORMATION
m
a
—
| -
¡General maintenance
Do not expose the set, batteries, CDs or tapes to humidity,
rain, sand or excessive heat (caused by heating equipment or direct
sunlight).
The mechanical parts of the set contain self-lubricating bearings
and must not be oiled or lubricated!
You can clean the set with a soft, slightly dampened lint-free cloth.
Do not use any cleaning agents as they may have a corrosive effect.
Tape deck maintenance
To ensure proper recording and playback quality, clean the parts
A), ® and © after approx. 50 hours of operation. Use a cotton
swab slightly moistened with alcohol or head-cleaner fluid.
Press PLAY <1 and clean the rubber pressure rollers ©).
Press PAUSE 11 and clean the capstans €) and the heads (A).
Note: Cleaning of the heads (8) can also be done by playing a
cleaning tape once.
CD player and CD handling |
The lens of the CD player should never be touched. Always |
keep the CD compartment closed to avoid dust on the lens.
The lens may cloud over when the set is suddenly moved from cold — |
to warm surroundings. Playing a CD is not possible then. Leave the - |
|
|
CD player in a warm environment until the moisture evaporates. I. =
To take the CD out of its box easily, press the centre spindle while ZZ |
lifting the CD. Always pick up the CD by the edge and put it back
in its box after use. > * | A ;
| e ‚ | / ft- 7 |, MA В ;
To clean the CD, wipe it in a straight line from the center toward | + ~~ - $
the edge using a soft, lint-free cloth. A cleaning agent may — | |
damage the disc!
Never write on a CD or attach a sticker to it.
This set complies with the radio interference requirements of the
European Community
14
TROUBLESHOOTING
WARNING
Under no circumstance should you try to
repair the set yourself as this will
invalidate the guarantee.
If a fault occurs, first check the points listed
below before taking the set for repair.
If you are unable to solve a problem by
following these hints, consult your dealer or
service center.
Problem Possible cause Solution
No sound, VOLUME is not adjusted. Adjust volume.
no power Headphone is connected. Disconnect headphone.
Mains cable is not securely connected.
Connect mains cable properly.
Batteries are flat.
Insert fresh batteries.
Batteries are inserted incorrectly.
Insert batteries correctly.
Trying to change over from mains to
battery supply without removing the plug.
Remove the mains plug from the
unit's AC MAINS inlet.
No reaction to
operation of any keys
Electrostatic discharge.
Disconnect the set from power supply,
reconnect after a few seconds.
Poor radio reception Weak radio signal.
Direct the antenna for optimum
reception.
Interference caused by vicinity of electrical
equipment like TVs, computers, engines, etc.
Keep the radio away from electrical
equipment.
na € {50 or The CD is badly scratched or dirty. Replace or clean the CD.
Ex Err indication No CD is inserted. Insert a CD.
The CD is inserted upside down. Insert CD with label upwards.
The laser lens is steamed up. Wait until the lens has cleared.
The CD skips tracks The CD is damaged or dirty. Replace or clean the CD.
SHUFFLE Or PROGRAM is active. Switch off SHUFFLE or PROGRAM play.
Poor cassette Dust and dirt on the heads, capstans or Clean heads, capstans, and pressure
sound quality pressure rollers. rollers.
Use of unsultable cassette types
(METAL or CHROME) for recording.
Only use NORMAL type cassettes for
recording.
Recording does
not work
Cassette tabls) may be snapped off.
Apply a piece of adhesive tape over
the aperture.
Remote control does Batteries are inserted incorrectly.
not function properly Batteries are flat.
Insert batteries correctly.
Insert fresh batteries.
Distance to the set is too large.
Reduce distance.
15
English
[ина pia] mos |v smn | soe or] on | nt | es | ne
3140 115 2371.1
Meet Philips at the Internet
http://www. philips.com
CE
CLASS 1
LASER PRODUCT
AZ1208
ViesRP9723
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement