Philips | MZ-1200/22 | User's Manual | Philips MZ1200 User's Manual

owner’s guide
MZ1000
MZ1100
MZ1200
1
3139 115 21641
Hook Up
Guide
12nc : 3139 115 21851
MZ-1000
MZ-1100
MZ-1200
PHONES
AUX IN
R
L
R
L
LINE OUT
1
TO POWER
UNIT
AM
FM
ANTENNA
2
3
Quick Use
Guide
Detailed playback
features and additional
functions are described in
the accompanying
owner’s manual.
õ Listening to radio station
First time power up...
1
2
3
“AUTO INSTALL PRESS PLAY” appears on the display.
Press PLAY•PAUSE ÉÅ on the system.
Once completed, you can listen to the last tuned radio station.
If “P” appears on the display, you can press S T to select the previous/next presetting radio
stations.
When tuning to a weak reception or non-preset radio station, press ÉÅ to deactivate the preset
mode (“P” will disappear from the display), then press S T.
õ Listening to a CD/MP3-CD
1
2
Load in a CD/MP3 CD with the label facing right.
For MP3-CD, press S T to select the album, followed by ÉÅ to confirm, then press
S T again to select the track.
For CD, press S T to select the track.
3
Press ÉÅ to start playback.
During playback, hold down S T to search backward/forward.
During playback, press S T briefly and repeatedly to skip backward/forward.
4
5
Press Ç to stop playback.
Press STOP•EJECT Ç to eject the disc.
õ Setting the Clock
1
2
3
4
In standby mode, press CLK/TIMER.
Press or hold down S T to set minutes and hours.
Press PROGRAM to select 12- or 24-hour clock mode.
Press CLK/TIMER to confirm the clock setting.
õ Switching to or waking up from Eco Power standby mode
1
2
Hold down ECO POWER or B to switch on Eco Power standby mode.
Press ECO POWER on the system or MP3-CD, TUNER or AUX on the remote control to
wake up from Eco Power standby mode.
Important notes for users in the
U.K.
Italia
DICHIARAZIONE DI CONFORMITA’
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
Si dichiara che l’apparecchio MZ1000, MZ1100,
MZ1200, Philips risponde alle prescrizioni dell’art.
2 comma 1 del D.M. 28 Agosto 1995 n. 548.
1
2
Remove fuse cover and fuse.
Fatto a Eindhoven
3
Refit the fuse cover.
Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
Norge
Typeskilt finnes på apparatens underside.
Note: The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
¶ As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
– Connect the blue wire to the terminal
marked N or coloured black.
– Connect the brown wire to the terminal
marked L or coloured red.
– Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous
radiation exposure or other unsafe
operation.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
2
3139 115 21641
DK
SF
Advarsel: Usynlig laserstråling ved åbning
når sikkerhedsafbrydere er ude af funktion.
Undgå utsættelse for stråling.
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen muulla
kuin tässä käyttöohjeessa mainitulla tavalla
saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei
saa olla alttiina tippu-ja roiskevedelle.
Bemærk: Netafbryderen er sekundært
indkoblet og ofbryder ikke strømmen fra
nettet. Den indbyggede netdel er derfor
tilsluttet til lysnettet så længe netstikket
sidder i stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat
sätt än i denna bruksanvisning specificerats,
kan användaren utsättas för osynlig
laserstrålning, som överskrider gränsen för
laserklass 1.
Huom.Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkkoosa on kytkettynä sähköverkkoon aina
silloin, kun pistoke on pistorasiassa.
Observera! Stömbrytaren är sekundärt
kopplad och bryter inte strömmen från
nätet. Den inbyggda nätdelen är därför
ansluten till elnätet så länge stickproppen
sitter i vägguttaget.
3
3139 115 21641
4
3139 115 21641
English
Index
Français
English ------------------------------------------------ 6
Español
Français -------------------------------------------- 24
Deutsch
Español --------------------------------------------- 42
Nederlands
Deutsch --------------------------------------------- 60
Italiano
Nederlands ---------------------------------------- 78
Svenska
Italiano ---------------------------------------------- 96
Dansk
Svenska ------------------------------------------- 114
Suomi
Dansk --------------------------------------------- 132
∂ÏÏËÓÈο Português
Suomi --------------------------------------------- 150
Português ---------------------------------------- 168
Polski
∂ÏÏËÓÈο ----------------------------------------- 186
Polski ---------------------------------------------- 204
5
3139 115 21641
Contents
English
General Information
Clock/Timer
Environmental information ................................ 7
Maintenance .......................................................... 7
Safety information ................................................ 7
About Clock ........................................................ 18
Connections
Supplied accessories ............................................ 8
Rear connections ............................................. 8–9
Setting the clock
About Timer ........................................................ 19
Setting the timer
Cancel/Disable the timer
Activating the timer to the last setting
Other Features
Switching on ........................................................ 20
Preparations
Before using the remote control .................... 10
Replacing battery (lithium CR2025) into
the remote control ............................................ 10
Placing the power box ...................................... 10
Introduction of Features ............... 11
Radio Reception
Plug and Play ........................................................ 12
First time setup/power up
Reinstalling Plug and Play
Switching on to tuner mode ............................ 12
Presetting radio stations ............................ 13–14
Automatic preset programming
Manual preset programming
Listening to the preset radio stations
Deleting a preset radio station
Switching to Eco Power standby mode
Switching to standby mode
Switching to active mode
Sound control ..................................................... 20
Adjusting the Bass/Treble level
Activating/deactivating Incredible Surround effect
Other Connections
Connecting external devices ........................... 21
Connecting an external device for listening
to music/sound
Connecting an external device for analogue
recording
Listening to an external source ...................... 21
Specifications ........................................... 22
Troubleshooting .................................... 23
CD/MP3-CD Operations
Discs for playback .............................................. 15
Loading/Unloading the disc .............................. 15
Inserting the disc
Ejecting the disc
Playing a CD/MP3-CD ....................................... 16
Selecting a desired MP3 Album/Track ............ 17
Programming the disc tracks ........................... 17
MP3-CD programming
6
3139 115 21642
This product complies with the radio
interference requirements of the
European Community.
English
General Information
Safety information
● Place the system on a flat, hard and stable
surface.
The type plate is located at the rear of the
system.
For users in the U.K.: please follow the
instructions on page 2.
● Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
Environmental information
● The lens may cloud over when the system is
suddenly moved from cold to warm
surroundings, making it impossible to play a disc.
Leave the system in the warm environment until
the moisture evaporates.
All unnecessary packaging has been omitted. We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialised company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Maintenance
To clean a CD, wipe it in a straight
line from the centre toward the
edge using a soft, lint-free cloth. A
cleaning agent may damage the
disc! Write only on the printed
side of a disc and only with a soft
felt-tipped pen.
● The mechanical parts of the set contain selflubricating bearings and must not be oiled or
lubricated.
● When the system is switched to Standby mode,
it is still consuming some power. To disconnect
the system from the power supply completely,
remove the AC power plug from the wall socket.
● To avoid overheating of the system, a safety
circuit has been built in. Therefore, your system
may switch to Standby mode automatically
under extreme conditions. If this happens, let
the system cool down before reusing it.
Clean the system with a soft,
slightly dampened, lint-free
cloth. Do not use any
cleaning agents as they may
have a corrosive effect.
Do not expose the system
batteries or discs to
humidity, rain, sand or
excessive heat (caused by
heating equipment or direct
sunlight).
7
3139 115 21642
Connections
English
Rear connections
Supplied accessories
Speakers
WARNING!
– Never make or change any
connections with the power switched on.
– Connect the power cord from the
“power box” to the power outlet only
after you have finished hooking up
everything.
● Adjust the position of the antenna for optimal
reception.
● Position the antenna as far as possible from a TV,
VCR or other radiation source.
● For better FM stereo reception, connect
external FM antenna.
Remote
control
Power box
● It is not possible to connect other than the
supplied speakers.
● The optional equipments and connecting cords
are not supplied.
● If you are connecting to equipment with only
mono output (a single audio out terminal),
connect it to the AUX IN left terminal.
Alternatively, you can use a “single to double”
cinch cable, but the output sounds still remain
mono.
AM antenna
Telescopic
antenna
● Do not connect equipment to both the
LINE OUT and AUX IN terminals at the same
time. Otherwise, noise will be generated and
malfunction might occur.
interconnect
cable
Power cord
FM antenna
8
3139 115 21642
English
Connections
alternative
FM antenna
connection
FM
ANTENNA
AM
PHONES
AUX IN
R
L
R
L
LINE OUT
TO POWER
UNIT
AM
FM
ANTENNA
➠
➠
➠
➠
9
3139 115 21642
Preparations
English
☞
Before using the remote control
1
2
Pull out the plastic protective sheet.
3
Then select the desired function (for exampleÉ,
S, T).
Select the source you wish to control by pressing
one of the source select keys on the remote
control (for example MP3-CD, TUNER).
Replacing battery (lithium
CR2025) into the remote control
1
2
3
plastic
protective
sheet
☞
Pull out the knob A slightly to the left
B
Pull out the battery compartment B.
A
➠
Replace a new battery and fully insert the
battery compartment back to the original
position.
CR 2
02
5
LI
TH
IUM
CAUTION!
Batteries contain chemical substances, so
they should be disposed off properly.
Placing the power box
☞
● Place the power box as close as possible to the
power supply.
● Do not place this unit in closed spaces, cover it
or block the air vents.
● Do not insert or drop anything into this unit
through the air vents as this could cause serious
damage.
10
3139 115 21642
Eco Power standby
ECO POWER or y
Plug and Play
ÉÅ
- in standby mode, press and hold to initiate
Plug and Play mode.
- press briefly to start plug & play installation.
Ç
press to exit.
- press and hold to switch the system to low power
standby mode.
Standby mode
ECO POWER or y
Volume
- press briefly to enter standby mode.
VOL 34, VOLUME +/- press to increase/decease the volume.
Source selection
SOURCE
VOL
MUTE
- press to silence or restore the volume.
VOL
press repeatedly to select :
CD ™ TUNER-FM ™ MW ™
AUX ™ CDR ™ CD ...
SOURCE
ECO
POWER
Sound control
I.S.
8 cm DISC
PLAY•PAUSE
CD GRAPHIC THIS SIDE
MP3-CD / TUNER / AUX
- press to enter the selected source mode.
- in Tuner mode, press TUNER to toggle
between FM and MW band.
- in AUX mode, press AUX to toggle
between AUX and CDR mode.
BASS /
TREBLE
SEARCH
Dimming the display
DIM
press to select half or full
brightness for display screen.
press to switch on/off the
incredible surround sound
effect.
- press to select low tone/high
tone sound effect.
- press VOLUME+/-on the
remote control to change the
tone level.
STOP•EJECT
iR
CD
Clock/Timer
CLK/TIMER
- press to view clock or enter clock setting mode.
- press and hold to enter timer setting mode.
PROGRAM
- in clock setting mode, press to change clock display
mode : 24- or 12- hour.
S T
press to set the minutes and hours.
ÉÅ
press to start or interrupt playback.
S T
- press briefly to select a desired track.
- press and hold to search backward/
forward.
Ç
- in playback mode, press to stop the
disc.
- in stop mode, press to eject the disc.
REPEAT
press to select repeat the current track
or repeat the whole disc or switch off
the repeat mode.
Tuner
MP3-CD
ÉÅ
press to toggle between frequency
tuning and preset number selection
mode.
S T
- press to select a preset radio station.
- press to change the radio frequency.
PROGRAM
- press to start manual preset programming.
- press and hold to start automatic preset
programming.
Ç
press to stop programming or to erase
a selected preset.
ÉÅ
- press to start or interrupt playback.
- press to enter track selection mode.
S T
press to select a desired album/ track.
Ç
- in playback mode, press to stop the
disc.
- in stop mode, press to eject the disc.
- press to enter album selection mode.
REPEAT
press to select repeat the current track
or repeat the whole disc or switch off
the repeat mode.
11
3139 115 21642
English
Introduction of Features
Radio Reception
English
Plug and Play
Plug and Play allows you to store all available
radio stations automatically, starting from FM and
followed by MW band.
When all the available radio stations are stored
or the memory for 40 presets are used, the last
preset radio station will be played.
ö First time setup/power up
☞
PLAY•PAUSE
➠
plug in the
power cord
ö Reinstalling Plug and Play
➜ All previously stored radio stations will be
replaced.
☞
In standby mode,
PLAY•PAUSE
PLAY•PAUSE
Notes:
– If no stereo frequency is detected during Plug
and Play, "CHECK ANTENNA" will be displayed.
– During Plug and Play, if no button is pressed
within 15 seconds, the system will exit Plug and
Play mode.
press and hold
To exit without storing the Plug and Play
● Press Çon the system.
➜ If you do not complete the Plug and Play
installation, the function will be restarted when
you next turn on the main supply again.
VOL
SOURCE
VOL
ECO
POWER
PLAY•PAUSE
➭
CD ➔ TUNER-FM
➠ CDR ➔ AUX ➔ MW
➔
SOURCE
CD GRAPHIC THIS SIDE
☞
SEARCH
MZ 1100
➔
Switching on to tuner mode
● Press SOURCE or TUNER repeatedly to
select FM or MW band.
STOP•EJECT
iR
➭
TUNER
➠ TUNER-FM î MW
12
3139 115 21642
English
Radio Reception
Presetting radio stations
You can preset up to 40 radio stations in the
memory.
IMPORTANT!
When “P” appears on the display, it only
enables preset number selection.
Press ÉÅ to toggle between frequency
tuning and preset number selection.
ö Automatic preset programming
☞
It enables you to programme all available radio
stations automatically from a selected preset
number, starting from FM and followed by MW
band.
In tuner mode,
➠
99 80
make sure “P”
appears, if not
pressÉÅ.
If no preset number is shown, automatic preset
will begin from preset (1) and all your former
presets will be overridden.
/
➠
P 01
press and hold
until “AUTO”
appears
select a preset
number
Note:
– If a radio station has been stored in one of the
presets, it will not be stored again under another
preset number.
To exit programming mode
● Press PROGRAM or Ç.
ö Manual preset programming
It enables you to programme only the favourite
radio stations.
☞
In tuner mode,
PROG
/
99 80
P 01
● Hold down S T for fast tuning, release it
when the frequency indication starts to change.
For tuning to a weak reception radio station,
press S T briefly and repeatedly.
● Repeat the steps again to store other radio
stations.
Notes:
– If you attempt to programme more than 40
preset radio stations, "PROGRAM FULL" is
displayed.
– During programming, if no key is pressed within
20 seconds, the system will exit the programme
mode automatically.
tune to a radio
station
PROG
99 80
/
P 01
select a preset
number
store setting and exit
programming mode
To exit without storing the preset setting
● Press Ç.
13
3139 115 21642
Radio Reception
English
ö Listening to the preset radio
stations
☞
In tuner mode,
➠
99 80
make sure “P”
appears, if not
pressÉÅ.
ö Deleting a preset radio station
☞
/
P 01
select a preset
number
In tuner mode,
STOP•EJECT
When the preset radio station is deleted
➜ The deleted radio frequency remains on the
display until you select another preset number.
➜ The preset numbers of all other preset radio
stations in the band with higher numbers are
also decreased by one.
➠
99 80
/
P 01
make sure “P”
appears, if not
pressÉÅ.
select a preset
number
➠
press and hold
until “PRESET
DELETED”
appears
Note:
– If you press the STOP•EJECT (Ç) button for
less than three seconds, it will eject the disc (if
available) from the disc loader.
14
3139 115 21642
English
CD/MP3-CD Operations
Discs for playback
This system is able to play :
– All pre-recorded audio CDs (8cm/12cm)
– All finalised audio CDR and audio
CDRW discs
– MP3-CDs (CD-ROMs with MP3 tracks)
maximum albums = 99
maximum titles = 999 (depending on filename length)
ISO9660/Joliet or UDF1.5 format
Bitrates = 32-256 kpbs, variable bitrates
ID3 tags = V1.1, V2.2, V2.3, V2.4
Loading/Unloading the disc
WARNING!
– Do not load more than one disc into
the disc loader.
– When loading an 8cm disc, slot into
the middle of the disc loader.
ö Inserting the disc
☞
Slot the disc slightly into the disc loader and
withdraw your fingers immediately.
➜ "READ" is displayed, followed by total number
of tracks and the playing time.
Notes:
– Load the disc with the label side facing right.
– Loading the disc in any source mode will switch
from the current mode to disc mode.
– For MP3 disc, the disc reading time may exceed
10 seconds due to the large number of songs
compiled into one disc.
ö Ejecting the disc
➜ All the programmed tracks will be erased.
☞
In stop mode,
STOP•EJECT
15
3139 115 21642
CD/MP3-CD Operations
English
Playing a CD/MP3-CD
You can also access the functions via the
same buttons on the remote control.
Searching backward/
forward
●
Switching on to disc
mode
●
Press SOURCE (or MP3-CD on the
remote control) to select CD mode.
During playback, hold down the
button until it reaches the desired
passage.
➜ For MP3 disc, it is only possible
to search within the current track.
Selecting a desired
track
●
VOL
VOL
●
Start / Interrupt /
Resume playback
In stop mode, press to start
playback.
During playback, press to pause.
In pause mode, press to resume
playback.
➜ During playback, the track
number and elapsed playing time of
the current track are displayed.
➜ For mixed mode MP3 discs, only
one mode will be selected for
playback depending on the recording
format.
SOURCE
PLAY•PAUSE
ECO
POWER
8 cm DISC
●
●
CD GRAPHIC THIS SIDE
●
Press the button briefly and
repeatedly to go to the beginning
of the current / next/ previous
track.
In stop/programme mode,
hold down the button to increase
the speed of track selection.
SEARCH
Stop playback / Eject
the disc
STOP•EJECT
iR
●
●
During playback, press to stop
playback.
In stop mode, press to eject the
disc.
Repeat play
●
Press REPEAT repeatedly to select :
➜ Repeat the current track – RPT lights up.
➜ Repeat all tracks – RPT ALL lights up.
●
Press REPEAT repeatedly until RPT ALL
disappears from the display.
To stop repeat play
Notes:
– If programme mode is active, it will repeat the
programmed tracks.
– When the disc is being ejected from the disc
slot, it will cancel the repeat mode.
16
3139 115 21642
Selecting a desired MP3 Album/
Track
☞
English
CD/MP3-CD Operations
After inserting the MP3 disc,
/
ALBUM TRACK
01
If you want to change the album after
confirming the selection
1
2
01
select an album
number
Press Ç while TRACK icon is flashing.
Press S T to select the desired album
and repeat steps 3-6.
confirm the
album selection
/
ALBUM TRACK
01 01
select a track
number
Programming the disc tracks
☞
Programming tracks is possible when playback is
stopped. Up to 99 tracks can be stored in the
memory in any order.
In stop mode,
PROG
➠
10:80
/
TRACK
01
select a track
number
If you attempt to programme more than
99 tracks, “PROGRAM FULL” will
appear on the display. In this case :
➜ The system will exit programming mode
automatically.
➜ Pressing Ç button will erase all the
programmed tracks.
➜ Pressing ÉÅ button will start the playback
of the programmed tracks.
ö MP3-CD programming
start playback
repeat steps 2 and
3 to store other
tracks
➠
PROG
98:80
TRACK
20
stop programming
mode
☞
start playback
In stop mode,
ALBUM
Notes:
– During programming, if no button is pressed
within 20 seconds, the system will exit the
programme mode automatically.
– The programme will be erased when the system
exits from CD source.
PROG
➠
10:80
ALBUM TRACK
➠
/
Once the programmed tracks have been erased,
pressing Ç will eject the disc.
10:80
ALBUM TRACK
select an album
number
TRACK
to store other
tracks under the
same album, repeat
steps 4 and 5
/
To erase all the programmed tracks
● In stop mode, press Ç.
PROG
01 01
01 01
select a track
number
to select tracks
from another album,
pressÇ and repeat
steps 2 to 5
stop programming
mode
start playback
17
3139 115 21642
Clock/Timer
English
IMPORTANT!
When in Eco Power standby mode, it is
not possible to view or set the
clock/timer.
Notes:
– The clock/timer setting will be cancelled when
the power cord is disconnected or if a power failure
occurs.
– During clock/timer setting, if no button is
pressed within 90 seconds, the system will exit the
setting mode automatically.
About Clock
The clock can be set in either 12-hour or
24-hour mode ("11:59 PM" or "23:59", for
example).
ö Setting the clock
If you press and hold S T for more than
two seconds, it will change the minutes in faster
speed. The changes in minutes will rollover to
the hours, refer to the example shown below.
AMPM
AMPM
11:59
î12:00 î
23:59
î
☞
In standby mode,
➠
set minutes
and hours
AMPM
12:01
00:00 î 00:01
➠ /
select clock
mode
To check the time in other source mode
● Press CLK/TIMER once.
To exit without storing the setting
● Press Ç.
18
3139 115 21642
English
Clock/Timer
About Timer
The system can switch to CD or TUNER mode
automatically at a preset time, serving as an
alarm to wake you up.
ö Setting the timer
☞
– Before setting the timer, ensure that the clock
is set correctly.
– The timer will always be switched on after it
has been set.
– The volume of the timer will increase
gradually from the minimum level to the last
tuned volume level.
– If the CD source is selected, the timer will
wake you up by playing the first track of the disc
or programmed track. If the disc loader is
empty, it will switch to Tuner mode.
– If the Tuner source is selected, the timer will
wake you up by playing the last tuned radio
station.
ö Cancel/Disable the timer
/
set minutes
and hours
press and hold
5
/
select the wake up
source
press to confirm and back
to the last active mode
☞
➠
press and hold
ö Activating the timer to the last
setting
☞
➠
press and hold
19
3139 115 21642
Other Features
OR
VOL
VOL
CD GRAPHIC THIS SIDE
☞
ö Switching to Eco Power standby
mode
SOURCE
➭
➭
ECO
POWER
PLAY•PAUSE
ECO
POWER
SEARCH
MZ 1100
STOP•EJECT
To save the power consumption, it is advisable to
switch the system to Eco Power standby mode
or disconnect the system from the power supply
completely when not in use.
➜ LED will display a red light.
➜ The display screen will go blank.
iR
press and hold
press and hold
OR
ö Switching to standby mode
☞
VOL
SOURCE
CD GRAPHIC THIS SIDE
➜ LED will display a green light.
VOL
➭
➭
ECO
POWER
PLAY•PAUSE
ECO
POWER
SEARCH
MZ 1100
STOP•EJECT
iR
press briefly
press briefly
☞
VOL
VOL
ECO
POWER
SOURCE
➭
➠
SEARCH
CD ➔ TUNER-FM
➔
CD GRAPHIC THIS SIDE
SOURCE
PLAY•PAUSE
➔
ö Switching to active mode
CDR ➔ AUX ➔ MW
MZ 1100
STOP•EJECT
iR
➭
/
/
Sound control
ö Adjusting the Bass/Treble level
☞
➭
/
To adjust the Bass or Treble tone level, press the
volume buttons on the remote control
immediately after you have selected the Bass or
Treble sound feature. If the volume button is not
used within five seconds, it will resume its normal
volume control function.
ö Activating/deactivating Incredible
Surround effect
☞
/
➠
The BASS (low tone) and TREBLE (high tone)
feature enables you to define the soundprocessor settings.
-3 î -2 î -1
î
English
Switching on
3 î 2 î 1 î 0
➭
IS
The Incredible Surround magnifies the virtual
distance between the front speakers for an
incredibly wide, enveloping, stereo effect.
➜ If the Incredible Surround is activated, IS is
shown on the display.
20
3139 115 21642
English
Other Connections
Connecting external devices
PHONES
ö Connecting an external device for
listening to music/sound
☞
AUX IN
PHONES
AUX IN
R
L
R
R
L
L
LINE OUT
Connect the “AUDIO OUT” terminals of the
external device (TV, VCR, Laser Disc player, DVD
player, for example) to the AUX IN terminals of
your system.
R
TO POWER
UNIT
L
AM
FM
ANTENNA
LINE OUT
AUDIO OUT
L
R
TO POWER
ö Connecting an external device for
analogue recording
☞
AUX IN
R
L
PHONES
AUX IN
R
L
R
Connect the “AUDIO IN” terminals of the
external device (CD/tape recorder, for example)
to the LINE OUT terminals of your system.
L
LINE OUT
R
L
LINE OUT
TO POWER
UNIT
AM
FM
ANTENNA
AUDIO IN
L
TO POWER
UNIT
R
AM
FM
Listening to an external source
● When CDR mode is selected, any audio
equipment connected to the LINE OUT
terminals will be muted. You will not be able to
record or listen to the sound on equipment
connected to the LINE OUT terminals.
VOL
SOURCE
VOL
SOURCE
ECO
POWER
PLAY•PAUSE
➭
CD ➔ TUNER-FM
➠ CDR ➔ AUX ➔ MW
➔
Play the external device.
☞
CD GRAPHIC THIS SIDE
2
Press SOURCE or AUX repeatedly.
➜ Select “AUX” when connecting to a TV, VCR
or Laser Disc player.
➜ Select “CDR” when connecting to a CD
recorder or DVD player.
SEARCH
MZ 1100
➔
1
STOP•EJECT
iR
➭
AUX
➠ AUX î CDR
Notes:
– You are advised not to listen to and record from
the same source simultaneously.
– All the sound control features (IS., BASS/TREBLE,
for example) are available for selection.
– Refer to the operating instructions of the
connected equipment for details.
21
3139 115 21642
Specifications
English
AMPLIFIER
Output power ..................................... 2 x 50 W MPO
................................................................... 2 x 25 W RMS(1)
Signal-to-noise ratio .......................... ≥ 67 dBA (IEC)
Frequency response .......................... 50 – 16000 Hz
Input sensitivity
AUX / CDR In ....................................... 500 mV / 1V
Output
Speakers .................................................................... ≥ 8 Ω
Headphones ...................................... 32 Ω – 1000 Ω
Line Out ...................... 500 mV ±2dB, > 22000 Ω
(1) (8 Ω, 1 kHz, 10% THD)
CD/MP3-CD PLAYER
Number of programmable tracks ......................... 99
Frequency range .................................. 20 – 20000 Hz
Signal-to-noise ratio ....................................... ≥ 80 dBA
Channel separation .......................... ≥ 60 dB (1 kHz)
Total harmonic distortion ........................... < 0.003%
MPEG 1 Layer 3 (MP3-CD) .......... MPEG AUDIO
MP3-CD bit rate ....................................... 32-256 kbps
(128 kbps advised)
Sampling frequencies ....................... 32, 44.1, 48 kHz
TUNER
FM wave range ................................... 87.5 – 108 MHz
MW wave range ................................ 531 – 1602 kHz
Number of presets ........................................................ 40
Antenna
FM ......................... 75 Ω wire /telescopic antenna
AM ............................................................ Loop antenna
POWER UNIT
Material .............................................................. Polystyrene
AC Power ..................................... 220 – 230 V / 50 Hz
Power Consumption
Active .......................................................................... 33 W
Standby ................................................................. < 10 W
Eco Power Standby ............................................ ≤ 1 W
Dimensions (w x h x d) .... 238 x 68 x 158 (mm)
Weight (without speakers) ................................. 1.2 kg
SPEAKERS
System ................................................................ Bass reflex
Impedance ........................................................................ 8 Ω
Woofer ......................................... 2 x 3” polypropylene
Tweeter ........ 1 x 18mm Ferrofluid cooled Dome
Dimensions (w x h x d) . 112 x 245 x 235 (mm)
Weight ................................................................ 2.9 kg each
GENERAL INFORMATION
Material
MZ1000 .......................... Polymethyl methacrylate
MZ1100 ................................................. Rubber/Lucite
MZ1200 ............................................. Aluminium alloy
Main unit
Dimensions (w x h x d)112 x 245 x 235 (mm)
Weight ..................................................................... 2.85 kg
Specifications and external appearance are
subject to change without notice.
22
3139 115 21642
English
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will
invalidate the warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If you
are unable to solve a problem by following these hints, consult your dealer or service centre.
Problem
Solution
The disc is ejected automatically.
✔ Load in the disc with label facing right.
✔ Replace or clean the disc, see “Maintenance”.
✔ Use a finalised CD-RW or a correct MP3-CD format
disc.
Radio reception is poor.
✔ If the signal is too weak, adjust the antenna or connect
an external antenna for better reception.
✔ Increase the distance between the system and your TV
or VCR.
The system does not react when buttons are
pressed.
✔ Remove and reconnect the AC power plug and switch
on the system again.
Sound cannot be heard or is of poor quality.
✔
✔
✔
✔
The left and right sound outputs are reversed.
✔ Check the speaker connections and location.
The remote control does not function
properly.
✔ Select the source (MP3-CD or TUNER, for example)
before pressing the function button (É, S , T).
✔ Reduce the distance between the remote control and
the system.
✔ Replace the battery.
✔ Point the remote control directly toward the IR sensor.
The timer is not working.
✔ Set the clock correctly.
✔ Press and hold CLK/TIMER to switch on the timer.
Adjust the volume.
Disconnect the headphones.
Check that the speakers are connected correctly.
Make sure the MP3-CD was recorded within 32-256
kbps bit rate with sampling frequencies at 48 kHz,
44.1 kHz or 32 kHz.
23
3139 115 21642
Download PDF

advertising