a
Quick Use
Guide
Connecting Speaker Cable
0.31"
(8mm) front right c
Centre
+
R
SPEAKER SYSTEMS (6 Ω )
L C SR SL
+
FRONT CENTER SURROUND
LX
8200SA
front left
12nc: 3139 115 22491
Helpful Hints:
You can listen to normal TV broadcast channels through the home cinema sound system from such an audio connection.
When listening to TV programmes, you have to set the DVD system to
TV / AV
mode in order for the sound to be heard.
Use this simple and quick way to watch your favourite DVD movie and enjoy your Home Cinema experience!
☞
AUDIO OUT
L
R
Helpful Hints:
If your TV is not equipped with a SCART connector, connect your TV through the corresponding CVBS A or S-Video B output.
Use Pr / Cr Pb /Cb Y jacks C connection if your TV can accept progressive signals (Progressive Scan
TV).
Notes: On the TV
- The CVBS jack may be labeled as Video, Composite or
Baseband and is usually yellow.
- The S-Video In jack may be labeled as Y/C, S-Video or
S-VHS.
- The Pr / Cr Pb / Cb Y jacks may be labeled as
Component Video In or YUV and are usually red, blue and green.
☞
A
CDR
DIGITAL
OUT
CENTER
OUT
AUX
IN
TV
IN
LINE
OUT
L
CVBS
VIDEO OUT
Pr/Cr
Pb/Cb
C
R
FM 75 Ω
Y
DIGITAL
IN
WOOFER
LINE OUT
AUDIO S-VIDEO
MW
FM/MW
ANTENNA
SCART OUT
B
Surround right
Surround left
Subwoofer
AUDIO
INPUT
Recommended Speaker Setup
Connect the DVD system and subwoofer to the power outlets only after you have finished hooking up everything.
AV IN
STANDBY-ON
ECO POWER
DVD VIDEO /SACD DIGITAL SURROUND SYSTEM
OPEN/CLOSE SOURCE
SURROUND
SOUND iR
SENSOR
VOLUME
Make sure your DVD system and TV are connected and turned on!
ö
Turning on the power and listening to preset radio stations
1 “
AUTO INSTALL- PRESS PLAY” will appear on the display. If not, press and hold ÉÅ on the system.
2 Press ÉÅ
on the system again to start installing all available radio stations.
3 Once completed, the last tuned radio station will play. Press
1 2 to select a preset radio station.
To tune to a non-preset radio station, press
S T briefly and repeatedly.
ö
Playing a disc
1 With the DVD system’s power on, press DISC on the remote control.
2
Turn on the TV power and set to the correct Video In channel or
STANDBY-ON
ECO POWER
DVD VIDEO /SACD DIGITAL SURROUND SYSTEM
Audio / Video mode. The DVD system’s blue screen will show on the TV.
The TV’s Video Input channel may be called AUX or AUX ILIARY IN, AUDIO/VIDEO or A /V IN,
EXT 1 or EXT 2, etc. These channels are often near channel 00. See your TV manual for details.
3
Press OPEN / CLOSE on the system and load a disc, then press OPEN / CLOSE again to close the disc tray.
4
Playback will start automatically. If not, press ÉÅ.
If a disc menu appears, use 3 4 1 2 to make the necessary selection, then press OK. Or, use the numeric keypad on the remote control to select features. Follow the instructions given on the disc menu.
5 During playback, you are able to change certain operations or features (for example, change the subtitle language, play in slow motion speed, etc.). Press SYSTEM MENU on the remote control, then use
3 4
1 2 to select your preferred options and press OK to confirm. To remove the menu bar, press
SYSTEM MENU again.
Please refer to the owner’s manual “Special DVD / VCD features” for more information.
6
To stop playback, press Ç.
OPEN/CLOSE SOURCE
POWER ON/OFF
SURROUND
SOUND iR
SENSOR
VOLUME
DISC 3
OPEN/CLOSE
DISC
SYSTEM
MENU
1 2 3 4
OK
Region Codes
DVDs must be labeled for ALL regions or for Region 2 in order to play on this DVD system.
ALL
2
ö
Playing other equipment connected to your DVD system
1 To use your DVD system’s home cinema surround capabilities, connect other
equipment and select the correct input source.
Please refer to the user’s manual “Connecting Additional Equipment” for more information.
2
Turn on and / or press PLAY on the equipment to start playback.
If necessary, connect the Video Output of the connected equipment (VCR or laser disc player) to TV for viewing purposes.
LX8200SA
Connect ...
DIGITAL
IN
AUX
IN
CD Recorder
➜
"DIGITAL OUT"
VCR /
Laser disc player
➜
"AUDIO OUT"
TV
IN Televeision
➜
"AUDIO OUT"
Select input source from the remote control
➜
AUX/DI
Press to select "
DI".
➜
AUX/DI
Press to select "
AUX".
➜
TV/AV
Press .
Detailed playback features and additional functions are described in the accompanying user’s manual.
