Philips MIC4013SB/27 User manual

Philips MIC4013SB/27 User manual
VGA Retro Camera
LOCATION OF CONTROLS
1. Shutter 2. Viewfinder 3. Lens
4. USB connector 5. Mode button 6. LED
7. Battery Door 8. LCD display
1.0 GETTING STARTED
1. Open the Battery Door and insert one AAA battery into the battery compartment making sure
that the battery terminals (+ and -) are properly positioned.
2. Close the Battery Door
3. Press the Mode button once, the camera will turn on. The camera will beep once and the
LCD will display the picture counter. The counter shows the number of images that are
stored in the camera. It will display “00” when the camera is first turned on.
2.0 TAKING A PICTURE
1. Verify the LCD is displaying the number of images taken. If the display is other than a
number, press the mode button until a number is displayed. If this is the first time the
camera has been activated, the LCD should display “00”.
. Next, look through the camera Viewfinder. Hold the camera steady and press the Shutter
button until you hear 2 beeps. A photo was taken successfully.
. The counter displayed in the LCD will be increased by one each time an image is captured.
. If the counter did not increase by one it may be because the Shutter button was not pressed
properly.
Ultimately, “FL” will be shown on the LCD display indicating that the camera memory is full.
Го
a so
3.0 The BATTERY and AUTO STAND-BY MODE
1. The camera will switch to stand-by mode after 60 seconds of inactivity. The LCD will go
blank to help conserve battery power.
2. Ifthe camera is in stand-by mode, pressing the Mode button once will bring the camera out
of stand-by mode. Any pictures taken will remain in the memory.
3. Any of the following indicates battery need to be replaced :
a. The LCD display keep flashing
b. When you press the “Mode” button, the LCD turns on once then goes off immediately.
c. When you press the “Mode” button, the LCD display does not turn on at all, it means
the battery power is running out and it is time to replace the battery.
Note: Always upload all images to PC before replacing the battery.
Low battery power will affect image quality & performance of the camera.
4.0 ADDITIONAL FEATURES
Press the mode button repeatedly until the desired features are shown on the LCD. Then press
the shutter button. If the desired feature is not selected in 5 seconds, the display will be
switched back to the Picture Counter.
00
5 E : Self Timer
: Picture Counter
H |: High Resolution (VGA)
39° : Video Clip Recording ! :Low Resolution (QVGA)
L 5 + Continuous Shooting for $ Images PU :1.3M Resolution by Interpolation
С A : Delete All Photos | 9 : Standard Image Quality
С В : Clear Last Photo Hg . High Image Quality
UU o : Mass Storage Device Mode 60 :60Hz
PL: PC Cam Mode
GO :50Hz
4.10 Self-Timer
wn =
. Press the Mode button until “ DE» appears on the LCD.
Press the shutter button to activate a 10 second self-timer.
The camera will issue a series beeping sounds and an image is taken successfully when
the beeping sound stops.
. The picture counter will increase by one to indicate that the image has been taken.
5. The Self Timer mode cannot be selected when the camera memory is full.
(i.e. “FL” displayed on the LCD)
4.20 AVI Video Clip
1.
2. a =. =
3. The camera allows to take video up to 10 seconds for each clip and maximum for 5 clips.
Press the Mode button until “ dB» is displayed on the LCD, then press the Shutter button
to start recording video. | ee
The LCD will display a Timer in seconds, starting from “01”.
The video recording will stop when the LCD shows “10”. Then it will switch back to the
picture counter. The picture counter will be increased by one.
On 4
Note: During the AVI mode, the camera automatically adjusts the exposure. :
‚ Video will be recorded in QVGA format (320 x 240).
If you want to stop the video recording, press the Shutter button once.
. The video recording stops when the memory is full, or if the Shutter button is being
pressed during recording.
#
>
4.30 Continuous Shooting for 3 Images
1.
oi
3.
4.
=
Press the “Mode” button until “ & >” is displayed on the LCD, then press the Shutter
button to begin Continuous mode.
The camera will take 3 images continuously and then stop. The Picture Counter will be
increased by one.
Continuous shooting stops when the memory is full.
40 Clearing the stored images
4.41 Delete All Photos
=
Press the Mode button until “ € #» appears on the LCD. Pressing the shutter button
once, you will hear one (1) beep and the picture counter will start flashing.
Press the Shutter button once and it will clear all the photos or AVI movies stored in the
camera and reset the picture counter to “00”.
4.42 Delete Single Photos
Press the Mode button until “CL « appears on the LCD. Press the shutter button once
and it will clear the last picture or the last AVI movie.
4.50 Image Resolutions
1. The camera is defaulted with the setting in “HI” - VGA resolution.
There are two resolutions available to select in the camera:
HI : High Resolution. This option will set the resolution to 640 x 480 VGA
Lo : Low Resolution. This option will set the resolution to 320 x 240 QVGA
PU : 1.3M Resolution by Interpolation. This option will set the resolution to
1280 x 960 1.3M Pixels.
Po
- Press the Mode button until “HI” appears in the LCD display. Then keep pressing the
Shutter button will display the following sequence:
Lo > HI > PU
. Select the desired resolution format then press Mode button to confirm the change.
4.60 Imdge Quality
High Quality and Standard Quality
1.” The camera is defaulted with the setting in * HS. High Quality.
2. To set to Standard Quality LS, press the Mode button until H3 appears in the
LCD. Press the “Shutter” Button once and the LCD will display Lg,
3. Press the Mode button once to confirm the mode change. The © 9 Standard
Quality is being selected.
Below is a table to show the maximum number of images can be taken at different
resolutions with different Image Quality:
4.70 Frequency Selection- when using as a Web camera (Video mode) or
Indoor Image Capturing
50Hz/60Hz Frequency mode
1. Select 50Hz or 60Hz according to the power frequency set in your living country to
avoid flickering under video mode or indoor image capturing.
2. The 60Hz frequency is set as a default. To select 50Hz frequency, press the Mode
button until “60” is displayed on the LCD, then press the Shutter button to confirm
selecting 50Hz.
Remark: It is recommended to choose 60Hz in North America.
5.0 INSTALLING THE SOFTWARE AND UPLOADING IMAGES TO PC
Windows 98 Users
To upload the images to PC, install the camera driver first. After this has been done, the
stored images in the camera can be moved to the PC.
Note: Do NOT connect camera to USB port prior to installing software and drivers.
“1. Insert the CD into the CD-Rom drive. The installation window automatically appears.
Ensure the camera is not connected to your computer.
2. Close out of all programs and disable any background applications such as Anti-Virus
software.
3. If the installation window does not appear, click the Start button on the desktop and
choose Run.
all
. Connect the camera to the PC with the USB cable.
4. When the Run dialog box appears, click the Browse button and navi
| ars, navigate to your CD-
ROM drive directory. Double-click the Setup.exe icon to begin the installation process.
>. An Install shield Wizard will be appeared. Click the “Next” button.
Welcome Lo the [mila heel wird For EZ ai
Ti iran e e rta Tn e pins
compa Teor cok Mend
letal ha fer ar Complète
Te eo ah Wed has gba lly rv Ls £2
Epos peas e ar yor Pres haga e pou But rés
compu
” Na | all plant Dep phen
Rercor any Sehr foe Sar Se aed Wn chek, Eps ne
e ed
“Building Driver Information” &
“New Hardware found” dialogue box will open and the computer will recognize the
camera.
New Hardware Found
pri Le EL |
E
Windows is
Y E TO are Of FOUT Fi By hardware
If you can see “Removable Disk” under “My Computer”, the camera driver installati
successful. on is
Ч [Tate]
LASA Ph eco Dr
ы = | Da 47168
E cel [rh 4066
р ЕСС
A Conbol Panel Spaten Folder
DINA Netrcdro Spetera Folder
Dl Schedule Taca Systems Folder
web Felden Syutera Folder
For Windows ME/2000/XP user
It is not necessary to install the camera driver to upload pictures if your computer runs on
Windows ME/2000/XP. Connect the camera to the computer and it will recognize the device
automatically. If you check the “Removable Disk” under “My Computer” exist, the
camera driver installation is successful.
6.0 UPLOADING STORED PICTURES
1.
2.
3.
Connect the camera to your PC with USB cable.
On your computer desktop display, select “My Computer” or “Windows Explorer” and
double click [Removable Disk] > [DCIM]> [100IMAGE]. The image files will then be
displayed
Use the COPY or MOVE function to download the images to your PC.
7.0 PLAYING AVI VIDEO
Follow the steps in 6.0 to upload all pictures/AVI Video files. Then select and double click
the AVI files in the dialogue box. It will automatically launch your default media player and
play the file.
8.0 DRIVER INSTALLATION TO VIEW LIVE VIDEO
8.10 Driver Installation
To view live video on PC, Windows ME/2000/XP users need to install the driver. Please
follow the steps in section 5.0. Windows 98 user is not required to repeat the installation
process.
1. After installation is completed, the PC cam mode needs to be activated in the camera
in order to view Live Video.
2. Toset to PC Cam mode, hold down the Shutter button first, then plug in the USB
cable.
. Do not release the Shutter button until the “ РС, is displayed in the LCD.
. Double click the icon “EZCam” on the Desktop. Select and double click the “PCCAM”
to start the Live Video Application.
E o
5. Live video will appear in the PCCAM window.
8.20 Video Capture
=
. Please set up the directory to which the file will be saved. Go to File -> select “Set
Capture File". Then select a directory and named a new file to save the video. The
click “Open” to save the link.
You can set the maximum recording file size by selecting the “Allocate File Size”
under the “File” menu.
To set the recording time of the video, go to “Capture” > “Set Time Limit”.
3. Goto “Capture” menu and select “Start Capture” > click OK. It will then start the
video capturing.
4. Press “Esc” on the computer keyboard whenever you want to stop, or go to “Capture”
menu and select “Stop Capture”.
5. Go back to the directory you set and select the saved file to view the video.
6. You can email the captured video to your friends / family by selecting the file you want
to send, then right click your mouse, select “send to” > go to “Mail Recipient”. It will
launch your email application and attaché your selected file to your email accordingly.
ho
8.30 Recording Audio
If your laptop has a built in microphone, or if you had installed a microphone on your
home PC, you are able to capture the audio while recording the video. The audio will be
attached in the same Captured video file.
Remark: External USB microphones are available at most computer stores.
If the microphone has not been built on the PC, it can be added subject to availability of
USB port. The USB ports could be expanded with a simple multi port hub.
5.4U video Lonterencing
You can use the digital camera to work as a Webcam to perform Video conferencing:
1. If the net meeting programs are not included in your Explorer®, download
“NetMeeting” from www.microsoft.com or “Yahoo® Messenger” from www.yahoo.com .
2. Connect your digital camera and start the net meeting programs. You can see your
friends and families if they are on the same net meeting program and have the web
camera set up.
9.0 REMOVING THE REMOVABLE DISK
9.10 Windows 98SE
1. Check that the camera is not transferring any files to the PC. Under transmission of files,
the LED will light up and flash, wait until the LED on the camera turns off.
2. Unplug the USB cable.
9.20 Windows 2000/ME/XP
1. Check whether the camera and PC are transferring a file and check if the LED is flashing,
wait until the LED on the camera turns off.
2. Double click the [Unplug or Eject Hardware] icon on the task bar as show in below :
DeL on
3. The [Unplug or Eject Hardware] window will open. Select the [USB Disk] and click the
i
in
[7 Dp devcs componente De |
[Stop] button.
Port Er TT Tin
= © lar Has clic pena енг К de неся. fe Мао Eid Sep When
‘wine és pots Pl né ae cals fn odo осы Мы фича я НР ри
ariel
mh charac
|
|
|
|
|
|
УЧ бей со ПАО Mars Stones Cirio
. The [Stop a Hardware device] window will open. Select [USB Mass Storage] and click
the [OK] button.
5. [Safe to Remove Hardware] window will open. Click [OK] button and the removable disk
will be removed safely.
RE a 1 RTT =jl
1) The USE Disk 6: * devican ar пет Пе сей некое Воть Не деи
6. Unplug the USB cable.
10.0 HINTS ON SOFTWARE INSTALLATION
The camera driver might share same resource files with other imaging device. In case
user encounter difficulties in software installation, uninstall driver of other imaging device and
reinstall the camera driver from beginning.
Helpful Hints and Camera Maintenance
Troubleshooting:
1. The camera does not work:
Make sure the battery has inserted with the correct polarity.
Check if the battery power is low / run out of battery, replace a new one.
2. “No New Hardware Found” message appears:
- Make sure the camera and PC are connected properly. Go to “My Computer” icon> Right
click your mouse> Choose “Property” > Select "Device Manager" > If you have encounter
below two situations :
(i) “Imaging Device” does not exist under the list
(il) The “Imaging Device” is on the list, check out if the driver named “EZ Cam”
exist, if not ,
unplug the camera and re-connect the camera into your computer's USB port.
Note: If the camera is listed, but other cameras are also installed, disable all other
cameras; make sure your camera is enabled.
3. “Camera not connected” or “Device cannot be detected” message appears:
Try removing the previous driver and reinstalling the software.
Go to “My Computer” icon> Right click your mouse> Choose “Property” > Select “Device
Manager” > “Imaging Device” > select the driver “EZCam” and choose “Remove” to
uninstall the driver:
EOS LA
Geral Device Manage | Harder Profes | Pertarmancs |
er drat By ca 7 ман by onnecion
[5 2 ен a
a
E df Favbosr
| ! x
|) Mos
an MP] Paper Clans
| Ш Невой, обор
Ea 4 LPT
№ он video ar garra conieales of
Poste | Feet | Ae: | Pie |
adi]
Then uninstall the driver program named “EZCam” under the “Add/ Remove program”
from the Windows Control Panel and restart the computer. Reinstall the driver again.
raat Urmnstal | Windoers Seng | Stat Dik |
= Tio erated wuss paras hoe a Sopoy deb. os CO-ADM
= dre, chi ей
=
[pea]
e wird To mare a program or Io mod e tall
gomponents, elect imo Pr he ad Ch К.
AAT rrr.
Char [| cra Language держи! E
[dF 20
After installing the camera software, the camera is not detected by the software:
Some PC's have been shipped without the USB port mode enabled. To enable the USB
Port. You must run the system CMOS setup program. This setup program is only available
when you power up the computer. The procedure is different for each system so you will
need refer to your PC manual for more details.
5. To Uninstall the Camera Driver:
-To uninstall the Camera Driver, go to Windows Start menu --> Programs--> EZCam--> click
“Uninstall”.
10
Camera Maintenance:
Maintaining your camera will ensure longer life and will minimize the chances of causing
damage to your camera and computer.
Keep the camera away from moisture and extreme temperature.
Clean the outside of the camera with a clean, dry cloth.
Never use harsh or abrasive cleaners or organic solvents on camera or on any of its parts.
Never disassemble or touch the inside of the camera.
11.0 ACCESSORIES
Your kit contains the following:
* Installation CD
* USB Cable
* Instruction manual
* 1 AAA battery
* Keychain
Note: Your computer needs a USB port to use your digital camera.
12.0 SYSTEM REQUIREMENTS
PC with Intel Pentium Ill 800MHz or Higher
Microsoft Windows 98SE/ME/2000/XP
128MB RAM or Higher
350MB available hard drive space
Available USB port
24-bit display adaptor
True Color (24-bit) display settings at 1024 X 768 pixels (recommended)
8X or faster CD-ROM drive
Mouse
© ео 8 ее бе #
Note: When using a USB connection, a PC running window 98 is required to upload pictures from
the camera. Window 95 does not support USB connection.
11
13.0 GENERAL SPECIFICATIONS
Resolution: 640 x 480 Pixels VGA resolution
320 x 240 Pixels QVGA resolution
1.3M by Interpolation
Internal Memory: 8MB SDRAM
Store a maximum 70 VGA images, or
170 QVGA images with High Image Quality, or
22 1.3M images by Interpolation
Record up to 5 AVI video clips, each at maximum 10 seconds
Self Timer
Auto Exposure and Auto White Balance
LCD display to show camera status
Video conferencing mode
Twain/VFW driver for Windows 98SE/ME/2000/XP
Use 1 x AAA size Alkaline battery
Fixed Focus
Weight about 30 grams
Dimension: 2.5"(L) x 1.8"('H) x 1.1"(D)
Specifications are subject to change without notice.
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement