Untitled - auto100.ro

Untitled - auto100.ro
Contents
User's Manual
Reasons to choose Steelmate -----------------------
2
17. Valet (service mode)---------------------------------- 11
Important notice ------------------------------------------
2
18. Emergency override ---------------------------------- 11
Brief look at transmitters ------------------------------
3
19. Turbo timer mode (F1, F19, F21)------------------ 12
About LCD screen ---------------------------------------
4
20. Transmitter operation range indication----------- 12
Battery indicator ------------------------------------------
4
21. Rearming automatically------------------------------ 12
Transmitter charging ------------------------------------
4
22. Ultrasonic sensor (optional)------------------------- 12
System operating-----------------------------------------
5
23. Tamper alert--------------------------------------------- 12
Status indication -----------------------------------------
6
24. Personal code setting--------------------------------- 12
Functions ---------------------------------------------------
7
24.1. How to enter the personal code------------ 13
1. Arming operation ----------------------------------------
7
2. Passive arming ------------------------------------------
7
3. Disarming operation------------------------------------
7
learning -------------------------------------------------- 13
4. Silent arming/disarming--------------------------------
8
26. System programming -------------------------------- 14
5. Mute arming----------------------------------------------
8
6. Car searching (locating)-------------------------------
8
Installation Manual
7. Remote sensor bypass------------------------------
8
System programming table --------------------------- 16
8. Central door lock/unlock (F3/F4/F15/F25) ---
8
Installation instruction---------------------------------- 21
9. Dome light delay-----------------------------------------
9
Door lock wiring diagrams ---------------------------- 24
10. Remote panic ------------------------------------------
9
Optional relay wiring diagrams----------------------- 25
11. Time/ alarm time/W-mode setting -----------------
9
Hood/trunk pin switch relay wiring diagrams--- 25
12. Low battery indicator -------------------------------
9
Wiring diagram--------------------------------------------- 26
13. Trunk release ------------------------------------------
9
Troubleshooting ------------------------------------------ 27
14. Arming without transmitters------------------------- 10
Warranty ----------------------------------------------------- 28
15. Anti-hijack mode --------------------------------------- 10
Steelmate warranty card-------------------------------- 28
24.2. How to change the personal code--------- 13
Car alarm system
25. Transmitter and transponder (optional) code
User's Manual
16. Transponder card (optional) ------------------------ 10
1
Reasons to choose Steelmate
Important notice
1. Professional manufacturer with German quality
standards.
* Please install the system by an authorized
engineer.
2. Complete range of products, you can easily
choose your favorite product.
* Keep the product and the transmitters away from
water.
Brief look at transmitters
Arm
Antenna
CH3
CH2
* It is highly recommended to read this manual
carefully before using this unit.
3. There are agents/distributors in more than 80
countries to supply local service.
* This product will help you reduce the possibility
of losing the car by discouraging theft. It is not a
substitute for owner’s vigilance. Please take the
valuables with you when leaving the car.
4. More than 100 engineers in the company, you
can enjoy the latest technology.
5. More than 300 patents.
* When the transmitter’s operating distance is
shorter or its indicator light turns dark, please
recharge the 2-way LCD transmitter or change the
battery of 1-way transmitter ASAP.
6. Products have international approvals, high
quality guaranteed.
7. Leading manufacturer in automotive industry,
ISO9001, ISO/TS16949, ISO14001 and
OHSAS18001 certified.
F button
CH2 button
Charging
socket
CH3 button
Arm
Disarm
Power ON/OFF
The LCD transmitter needs to be turned on before the first use, the factory setting is OFF.
Turn LCD transmitter ON: press and hold button for 3 seconds till the transmitter is turned on with melody.
Turn LCD transmitter OFF: press and hold button for 5 seconds till the transmitter is turned off with a beep.
Transmitter will be shut down when the battery is used up. If the transmitter cannot be turned on, please
charge it first.
LCD transmitter
is OFF.
2
Disarm
Press button for about
3 seconds till the transmitter
is turned on with melody.
3
The backlight will turn on,
the icons will light up.
About LCD screen
Battery indicator
System operation
The battery status of the LCD transmitter will
be shown on the LCD display.
Button
Button function
Button function optional
Lock doors & arm the system
Press and hold for 2 seconds to arm in mute
mode (with siren turned off for one arm cycle)
Unlock doors & disarm the system
Stop alarm
CH2
Press and hold for 2 seconds to activate
channel CH2
Press twice to cancel the turbo timer
CH3
then CH2
Press to activate channel CH3
Arm with the 1st-stage of shock sensor
bypassed
then CH2 then CH2
Arm with both sensors bypassed
When the battery indicator is empty, the
transmitter needs to be charged immediately.
The transmitting range
will be affected when
the battery is low.
Battery is full Battery is low Battery is empty.
Transmitter charging
Signal bar
Parking lights
flashing
Arming with
door locked
1st-stage shock
sensor bypass
Disarming with
door unlocked
Shock sensor
bypass
Arming in
mute mode
Hoodopened
CH2 then
Silent arming
CH2 then
Silent disarming
CH2 + CH3
Press and hold for 2 seconds for panic
mode
Arming mode
Charge the transmitter when the battery is low
according to the description below. The transmitter's
battery can be charged discontinuously.
Trunk released
+
+ CH2
Press and hold for 2 seconds for antihijack mode
Press and hold for 2 seconds for car
locating
Press and hold for 2 seconds and then
press CH2 for mute arm with the first stage
of shock sensor bypassed
Press and hold for 2 seconds and then
press CH2 twice for mute arm with both
sensors bypassed
Press both buttons in armed status for mute
arming
Press and hold for 2 seconds twice in 7
seconds to cancel passive arming for one
cycle
2-way transmitter
Key
Clock alarm
Ignition ON
System
busy
Transmitter
vibration
Time/Clock
and W-function
Anti-hijack
W-mode
ON
Valet mode
Door opened
Insert the charger’s plug
into transmitter’s battery
charging socket.
4
Insert the charger into the
vehicle’s cigarette lighter socket.
F (2-way transmitter)
Press and hold for 5 seconds for
Time/Alarm time/W-mode setting
F and
(2-way
transmitter)
Vibration on/off mode
F and CH3 (2-way
transmitter)
Turn on/off W-mode
CLOCK SETUP: CH2 = Increase, CH3= Decrease, F = Next,
Start = Beep with button press, hold F for 1 second = Exit
5
Status indication
Functions
LED indicator flashing table
1) Fast flashing---passive arming mode
Parking lights flashing table
1) 1 flash --- system armed
2) Slowly flashing ---armed mode
2) 2 flashes --- system disarmed
3) No flash----system disarmed
3) 3 flashes --- system armed with door, hood or
trunk opened
4) Turn on solid --- valet mode
4) 4 flashes --- warning about system triggered
after disarming
5) 1 flash ... pause --- the first stage shock sensor
triggered
1. Arming operation
To arm the system, press transmitter button :
* The siren will chirp once.
* The parking lights will flash once.
* The doors will be locked.
* The LED will start flashing.
The system is armed with engine immobilized. LCD
transmitter will beep once and display as below:
If the door or trunk is not closed properly after arming
the system, the siren will chirp 3 times with the
parking lights flashing, and transmitter will beep 3
times with door icon flashing.
2. Passive Arming
F23-- set passive arming ON/OFF,
F24-- set door lock/unlock in passive arming
When passive arming function is on, after 30 seconds
(plus F6 arming delay time), the system will be armed
automatically if the car is parked with all the doors
closed, the sire will chirp once and the parking lights
will flash once. The LED will flash.
5) 5 flashes --- car searching
6) 2 flashes ... pause--- the second stage shock
sensor triggered
7) 3 flashes ... pause --- trunk/hood triggered, INST
1 / INST 2 = INST 1
Note: opening the door resets the passive arming timer.
8) 4 flashes ... pause ---door triggered (door (-) or
door (+))
When passive arming function is on, press and hold
button +
twice for 2 sec in 7 seconds after the
car is parked with all doors closed, it will cancel
passive arming for one cycle. If anti-hijack is activated,
it will also be cancelled for one cycle.
While armed, the system will be triggered if:
* The door is opened.
* The trunk/hood is opened.
* The ignition is turned on.
* The shock sensor detects an impact.
* An optional sensor is triggered.
If triggered by the door or trunk/hood input or ignition
ON, the siren will sound and the parking lights will
flash for 30 seconds.
9) 1 long flash and 3 short flashes---transponder
registration confirmed
Siren short chirps table
1) 1 chirp --- system armed
2) 2 chirps --- system disarmed
3) 3 chirps --- system armed with door or trunk
opened.
Factory setting: passive arming OFF.
Note: if the ignition on or trunk is opened in 30 seconds,
the passive arming will be cancelled for one cycle.
3. Disarming operation
To disarm the system press transmitter button
* The siren will chirp twice.
* The parking lights will flash twice.
* The doors will unlock.
The LCD transmitter will beep twice and display as
below:
If the shock sensor detects a light impact to the
vehicle, the system will chirp and the parking lights
will flash 5 times to warn away the potential intruder.
A heavy impact will trigger the alarm system or an
optional sensor is disturbed, the siren will chirp and
the parking lights will flash for 30 seconds.
4) 4 chirps --- warning about system triggered after
disarming
5) 5 chirps --- car searching/locating
6
7
F4/1: Doors will not be unlocked when the ignition
turns off.
4. Silent arming/disarming
Press transmitter button
, then press button
or , the system will arm or disarm without siren
chirp(s).
7. Remote sensor bypass
To arm the system and bypass the 1-stage of the
shock sensor: press button , then press button
in 3 seconds, the siren chirps once and the 1-stage
of the shock sensor will be ignored for one cycle.
5. Mute arming
Press and hold transmitter button for 2 seconds
to arm in mute mode
* The siren will not chirp for one cycle
* The parking lights will flash once.
* The doors will lock.
When the system is triggered, the siren will not chirp.
The LCD transmitter will show as below:
To arm the system with both sensors bypassed: press
button , then press button
twice in 4 seconds,
the siren chirps twice and both sensors will be ignored
for one cycle.
The operation of remote sensor bypass in mute
arming mode is the same.
8. Central door lock/unlock (F3/F4/F15/F25).
F3/1: Doors will not be locked when ignition turns on.
F3/2: Doors will be locked automatically when ignition
is turned on.
F3/3: If you program F15/2 for speedometer input,
doors will be locked automatically when the car speed
reaches the pre-set speed.
F3/4: If you program F25 for "door +" or "door -", and
connect wires to footbrake signal wires, doors are
locked when the foot brake is pressed.
6. Car searching (locating)
Press and hold transmitter button +
for 2
seconds, the siren will chirp and parking lights will
flash 5 times.
Note: If one of the doors are not closed properly, the doors
will not be locked.
8
F4/2: Doors will be unlocked automatically when the
ignition turns off.
once, the hour digit will flash, then press button ,
the flashing icon will change in the sequence below:
time/hour time/minute alarm on/off alarm/hour
alarm/minute W-mode setting exit.
During driving, press button
the doors
Press "
" to increase (+) or press "
decrease (-).
or
to lock or unlock
" to
9. Dome light delay
This function is specifically designed for the vehicle
with dome light function. The system will enter the
arming mode after the dome light turns off. Arming
delay time can be set by F6.
Press and hold button
exit setting.
for 1 second to save and
10. Remote panic:
In the event of an emergency (panic) situation, the
siren can be triggered for 30 seconds to attract
attention. Press and hold transmitter button
+
for 2 seconds to activate the panic function:
* The siren will chirp sharply.
* The parking lights will flash.
"W-mode" means the time of transmitter sending
signals to system can be programmed.The "set"
icon will be shown on the LCD transmitter.
W-mode: Press +
button together shortly to
turn W-mode on/off. According to F21, CH6 can
be activated.
12. Low battery indicator
The battery status of the LCD transmitter will be
shown on the LCD display. When the battery
indicator is empty, the transmitter needs to be
charged immediately.
Press and hold transmitter button
+
for 2
seconds or press valet switch (if a personal code is
set, you should enter the personal code) to exit.
13. Trunk release
Press
or
button to open the trunk. The
shock sensor will bypass when the trunk is opened,
and return to normal when the trunk is closed.
11. Time/ alarm time/W-mode setting
Press button + to turn on/off the LCD transmitter's
vibration mode.
Press and hold button for 5 seconds to activate
time /alarm time /W-mode setting mode.
Press button once, the LCD transmitter beeps
The vehicle must equip with trunk release motor
and select
or
output for trunk release
during installation.
9
14. Arming without transmitters
Press valet switch once, then press and hold it
again for 3 seconds. The siren will chirp once, the
LED will flash rapidly. The system will be armed
after all doors are closed and send the signals to
LCD transmitter. If F24 is on, then the doors will
be locked. This function is only for one operation.
15. Anti-hijack mode
Anti-hijack mode will be activated automatically or
by transmitter (Function F16/F17/F18).
Five anti-hijack modes can be programmed:
1) Anti-hijack off.
2) Active: press and hold transmitter button +
for 3 seconds to activate the anti-hijack function.
3) Full-time: anti-hijack function will be activated
as soon as ignition is turned on.
4) Passive activated with door opened: During
driving, opening the door will activate anti-hijack
function.
5) Passive activated by speed: the pre-set speed
will activate the anti-hijack function.
engine will be blocked periodically.
3) 40 seconds later, the siren will chirp with parking
lights flashing rapidly until the car battery is used
up, the engine will be blocked completely.
If door is opened and stays open, then the system
will delay transponder card searching for 4 minutes.
One more minute later, if transponder card is not
found, the engine will be blocked.
If you place the transponder card in the working
range after 40 seconds when anti-hijack function
is activated, you need to deactivate anti-hijack, by
valet switch or enter personal code.
To deactivate the anti-hijack function:
1) In 40 seconds, press valet switch once.
2) 40 seconds later, to deactivate the anti-hijack
function depends on the setting of F12.
I. F12 is "Valet" - turn ignition OFF/ON and press
valet switch once in 10 seconds.
II. F12 is "Personal code" - enter personal code by
valet switch [24.1].
II. To change this protection mode, change F25 for
"door +" or "door -" and connect corresponding
door trigger wire to the footbrake wire.
17. Valet (service mode)
To activate Valet mode:
Disarm system, turn ignition on for more than 3
seconds then turn off, press the valet switch once
in 5 seconds. The LED will turn on solid. The siren
will chirp once every time when the ignition is turned
off in valet mode.
16. Transponder card (optional)
Please program transponder card into the memory of
the system before use.
3 modes of transponder card can be programmed
(Function F13)
1) F13/1 Transponder card is deactivated.
2) F13/2 Transponder card is activated with engine
block function:
I. Once ignition is turned on, the system starts to
search transponder card in 1 minute. If the system
finds transponder card, the LED indicator flashes
(1 long + 3 short) and the system will send signal
to the LCD transmitter.
ACC off can stop alarm temporarily. Once ACC is
turned on, the system will alarm and block the
engine.
Once the anti-hijack mode is activated:
1) In 20 seconds, the anti-hijack icon flashes on
the transmitter, the siren does not chirp.
2) 20 seconds later, the siren will chirp and the
If system can not find transponder card in 1 minute,
the engine will be blocked.
10
The following will happen:
* If door is opened, the system will search
transponder card when the footbrake is pressed.
* If the footbrake is pressed and transponder card
is not found in 1 minute, engine will be blocked.
* If door is opened, the system will search
transponder card in 4 minutes when the footbrake
is not pressed.
* If transponder card is registered successfully with
door closed, pressing footbrake will not activate
transponder card searching, opening door will
activate transponder card searching.
In valet mode, doors lock/unlock and panic functions
can be operated by transmitter.
To deactivate valet mode:
Turn ignition on for more than 3 seconds then turn
off, press valet switch in 5 seconds.
18. Emergency override
If the transmitter is lost or fails to operate, the system
can be disarmed by using the emergency override
feature. To override the system depends on F12.
3) F13/3 Transponder card is activated with antihijack function: once ignition is turned on, system
will search transponder card. If system does not
find transponder card in 1 minute it will activate
anti-hijack.
F12 -"Valet":
Opening the door with key ( the siren will chirp). Turn
ignition on, press valet switch once in 10 seconds.
F12 -"Personal code":
Enter the personal code [24.1].
If wrong personal code was input three times, you
need to wait for more than 3 minutes to enter personal
code again.
If you place the transponder card in the working
range in 40 seconds when anti-hijack function is
activated, anti-hijack will be stopped.
11
19. Turbo timer mode (F1, F19, F21)
The time can be programmed (F1). Turbo timer
works after the engine runs for more than 60 seconds.
If the turbo timer mode is on, when you take out the
key, the engine will keep running, the parking lights
will flash once every 2 seconds. The remaining time
will be shown on LCD transmitter.
transmitter shows that the transmitter is within the
operation range of the system. The signal icon will
disappear in 2 minutes when the LCD transmitter is
out of the operation range and cannot receive the
signal from the system. At the same time, 2 beeps
will be heard when any LCD transmitter button is
pressed.
Turbo timer mode keeps the engine running after
arriving at you destination for a programmable period
of 1, 3, 10, 15 or 30 minutes (F1). This allows the
system to cool down the turbo after you have left
the vehicle.
When a transmitter sends signal to the system, the
system only send feedback signal to the transmitter.
21. Rearming automatically
When the system is disarmed by pressing button
and the doors are not opened in 20 seconds (plus
F6 arming delay time), the system will rearm with the
doors locked automatically (door lock or unlock is
determined by F5). The siren will beep once with
parking lights flash.
To activate turbo timer mode, "turbo timer output"
(F19/2 or F21/2) needs to be set.
* Turn off the key, the engine will keep running.
* The LCD transmitter will beep 3 times and the
display will show:
* The parking lights will flash once every 2 seconds
to indicate the turbo timer mode is on.
* The engine will turn off after the programmed time
runs out.
22. Ultrasonic sensor (optional)
When the ultrasonic sensor is triggered by detecting
an object movement inside the vehicle, the siren will
alarm for 30 seconds with parking lights flashing. The
engine will be immobilized.
23. Tamper alert
If the alarm was triggered while you are away from
the vehicle, the siren will chirp 4 times with the parking
lights flash on disarming for tamper indication. The
LED will flash the zone that was triggered.
To cancel turbo timer mode:
a) Take the key out
b) Press button
twice
c) Siren will chirp twice and the parking lights will
flash once.
24. Personal code setting
Personal code can be programmed (F12). The factory
setting personal code is 11.
20. Transmitter operation range indication
In armed mode, the signal icon on the operated LCD
12
24.1. How to enter the personal code:
Disarm system, turn ignition off and wait for 5
seconds, then turn ignition ON/OFF/ON.
Press and release the valet switch the number of
times according to the first digit of personal code
in 10 seconds. (eg. The first digit of factory setting
personal code is 1, press and release the valet
switch once).
10 seconds, the siren will chirp accordingly. Turn
ignition on, the siren will send out one short and one
long chirp to confirm the new personal code is set
successfully.
If the changing is not successful, please disarm the
system and repeat the procedure mentioned above.
25. Transmitter and transponder (optional) code
learning
To learn new transmitters, the learning procedures
will be different depending on the settings of F12:
Turn ignition OFF/ON.
Press and release the valet switch the number of
times according to the second digit of personal code
in 10 seconds.
F12 - valet
Switch off the power of the transponder card (if
available)
Turn ignition OFF/ON.
When the input personal code is correct, the system
will send out a "short" chirp and a "long" chirp.
Disarm system, turn ignition on.
Press valet switch 3 times, the siren will chirp once.
Press and hold button on the first transmitter till
one chirp is heard, and then LED will start to flash
slowly.
Press and hold button on the second transmitter
till one chirp is heard, and then LED will start to flash
slowly.
Only 2 transmitters can be programmed for the
system.
24.2. How to change the personal code:
After the correct personal code is entered, turn
ignition off in 5 seconds.
Press valet switch 5 times, the siren will send out
one short and one long chirp to confirm entering the
setting mode.
Press transmitter button once in 5 seconds (the
siren will chirp once).
Press valet switch the number of times according
to the first digit of the personal code (from 1 to 9)
in 10 seconds, the siren will chirp accordingly.
Press transmitter button once in 10 seconds (the
siren will chirp once).
Press valet switch the number of times according
to second digit of personal code (from 1 to 9) in
Switch on the power of transponder card, the
transponder card will be programmed successfully
with one chirp.
Turn ignition off to exit or 10 seconds later to exit
automatically.
13
F12 - personal code
Switch off the power of the transponder card (if
available)
Follow the steps of "How to enter the personal
code" [24.1], the siren will chirp once to confirm if
personal code is correct.
Press valet switch 3 times, the siren will chirp once.
Only 2 transmitters can be programmed for the
system.
Switch on the power of transponder card. The siren
will chirp once to confirm transponder card is
programmed (If available).
Turn ignition off to exit or 10 seconds later to exit
automatically.
System will enter the F1 programming mode (LED
will flash once after one pause).
In programming mode, the number of times LED
flashes is corresponding to the function number.
To change function setting, press transmitter button
(1~5 times). According to the different function
settings, the siren will send out 1/2/3/4/5 chirps.
Press valet switch to go to next function.
If you do not press any button in 10 seconds,
system will exit programming mode.
F12 - Personal code: function programming
Enter the personal code [24.1].
Siren chirp will confirm if personal code is correct.
Press valet switch 3 times in 3 seconds. Siren will
chirp once.
Turn ignition off in 3 seconds. Siren will chirp once.
Turn ignition on in 3 seconds. Siren will chirp once.
System will enter the F1 programming mode (LED
will flash once after a pause).
26. System programming
F1-F10 can be programmed and it is independent
of F12.
F12 - valet
F1-F25 can be programmed.
F12 - personal code
F1-F10 can be programmed without personal code.
F11-F25 can be programmed only after entering
personal code. System will exit programming mode
if there is no button pressed in 10 seconds.
Car alarm system
Installation Manual
In the programming mode, the number of the LED
flashes is corresponding to the function number in
system programming table.
To change function setting, press transmitter button
. According to the different function settings, the
siren will send out 1/2/3/4/5 chirps.
F12-valet: function programming
Disarm system, turn ignition on, press valet switch
3 times in 3 seconds. Siren will chirp once.
Turn ignition off in 3 seconds. Siren will chirp once.
Turn ignition on in 3 seconds. Siren will chirp once.
Press valet switch to program next function.
If you do not press any button in 10 seconds,
system will exit programming mode.
14
15
System programming table
Continued
Function Description
System programming table
Function Description
1 chirp
Press button
once
2 chirps
Press button
twice
3 chirps
Press button
3 times
F1
Turbo timer
1 min
3 min
F2
Limitation of
false alarm
Off
On
F3
Ignition
locking
Off
On
F4
Ignition
unlocking
Off
On
F5
Auto rearm
Off
On with
unlocking
On with
locking
F6
Arming delay
5 sec
35 sec
60 sec
F7
Door locking/
unlocking
pulse
0.5 sec
1 sec
3.5 sec
F8
F9
CH2 output
10 min
4 chirps
5 chirps
Press button
5 times
Press button
4 times
15 min
30 min
Footbrake
Speed locking locking (Ref.F25)
1 sec unlock
pulse ×2
button CH2 again
to stop
Press button CH3, Press button CH3, Press button CH3 Press button CH3, Press button CH3,
signal "-" 3.5 sec 0.4 sec, signal "-" signal "-" 0.4 sec, signal "-" 1 sec,
pause 0.3 sec, pause 0.5 sec,
12 sec
CH3 output signal "-" 1 sec
CH4 output
When armed,
signal "-" 1 sec
When armed,
When armed,
When disarmed,
When armed,
signal "-" 10 sec signal "-" 15 sec signal "-" 30 sec signal "-" 20 sec
Restore
factory setting
Off
2 chirps
4 chirps
5 chirps
On
F12
Valet/Personal
mode setting for
programming
Valet mode
F13
Transponder
card
Off
On
F14
Ignition
warning in
disarmed
mode
Off
On
F15
INST2 (-)
extra input
trigger
F16
Anti-hijack by
transmitter
Off
On
F17
Anti-hijack by
ignition on
Off
On
On by driver
side door
opening (-)
F18
Anti-hijack by
ignition on
Off
On by driver
side door
opening (+)
On by speed
F19
INST2 (-)
extra input
trigger
Personal code
On while antihijack activated
Speedometer
input (-)
Turbo timer
output (-)
To be continued
To be continued
16
3 chirps
Programming the function F12- F25 depends on the mode of F12, "valet mode" or "personal
code mode" are available.
Press button CH2 Press button CH2 Press button CH2, Signal "-" when
signal "-" 30 sec signal "-", press ignition on
signal "-" 1 sec
signal "-" 0.4 sec signal "-" 1 sec
F10
F11
1 chirp
17
Continued
Function Description
1 chirp
2 chirps
F20
CH5 output
F21
When disarmed,
CH6 output:
two blue/black signal "-" 20 sec
wires
F22
Window/
sunroof closer
F23
Passive
arming
Off
On
F24
Door lock if
passive
arming on
Off
On
F25
STOP (-/+)
function of
door trigger
3 chirps
4 chirps
5 chirps
Pager (-)
Off
Off
Turbo timer
(-)
10 sec
W-trigger (start W-trigger (start W-trigger (start
and stop by
for 1 sec by
for 1/0.5/1 sec
real time)
real time)
by real time)
15 sec
22 sec
30 sec
F3/4: the doors will be locked when footbrake is
pressed (by F25) automatically.
The system will not lock the doors if any door is
opened when the ignition is turned on.
to turn on device, such as releasing trunk.
F8/2: the blue wire will output signal (-) for 30
seconds to roll up windows.
F8/3: the blue wire will output signal (-), press CH2
button again to stop output signal (-).
F8/4: the blue wire will always output signal (-) after
ignition on.
F4 Ignition unlocking
F4/1: the doors will not be unlocked when ignition
is off;
F4/2: the doors will be unlocked automatically when
ignition is off;
F9 CH3 output
Press transmitter button CH3 to activate this feature:
F9/1: the green/red wire will output signal (-) 1
second to turn on device, such as releasing trunk.
F9/2: the green/red wire will output signal (-) for 3.5
seconds.
F9/3: the green/red wire will output signal (-) for 12
seconds
F9/4: the green/red wire will output signal (-) for 0.4
seconds, pause 0.3 seconds and then output signal
(-) for 0.4 seconds again.
F9/5: the green/red wire will output signal (-) for 1
second, pause 0.5 seconds and then output signal
(-) for 1 second again.
F5 Auto rearm
Automatically rearms the system in case of
accidental disarming. Select among auto rearm off,
auto rearm without door locking and auto rearm
with door locking.
Door (+)
Door (-)
The shaded options are factory setting
Note:
F1 Turbo timer
Turbo timer function will be activated after ignition
is on for more than 1 minute (F19/2 or F21/2 need
to be programmed). It will keep a turbo vehicle
engine running for 1, 3, 10, and 15 or 30 minutes
according to F1 after you remove the key.
input, keeping the other zones protected until the
next time the system is armed.
F3 Ignition locking
F3/1: the doors will not be locked automatically
when ignition is on;
F3/2: the doors will be locked automatically when
ignition is on;
F3/3: the doors will be locked when the car's speed
reach the pre-set speed (with F15/2)
F2 Limitation of false alarm
If the same input triggers the system 6 times during
a single arming cycle, the system will bypass that
18
F6 Arming delay
This optional arming delay mode allows system to
delay arming for 5, 35 or 60 seconds. This mode
is designed for vehicle with dome light delay.
F7 Door lock/ unlock pulse
Select between a 0.5 second lock/0.5 second unlock,
1 second lock/1 second unlock for standard vehicles,
3.5 seconds lock/3.5 seconds unlock for vacuum
lock system, 1 second lock/1 second unlock 2 times
for some Japanese vehicles.
F10 CH4 output:
F10/1~4: When the system is armed, the
Green/White wire can output signal (-) for different
time to activate other devices: 1 second, 10 seconds,
15 seconds or 30 seconds.
F10/5: when the system is disarmed, the
Green/White wire will output signal (-) for 20 seconds.
F8 CH2 output
Press transmitter button CH2 to activate this feature:
F8/1: the blue wire will output signal (-) for 1 second
19
Installation instruction
F11 Restore factory setting:
This option allows the system to restore the factory
setting rapidly.
F16 Anti-hijack by transmitter
To activate the anti-hijack by pressing transmitter
button and
together when ignition is on.
F12 Valet/Personal mode setting for programming
There are two modes of F12: Valet mode and Personal
code mode.
When F12 is in Valet mode, you can program the
functions/features of F12~25 through Valet switch.
When F12 is in Personal code mode, you can program
the functions/features of F12~25 by input personal
code.
F17 Anti-hijack by ignition on
To activate the anti-hijack by ignition on or by a
door opening (-) while the ignition is on.
F18 Anti-hijack by ignition on
To activate the anti-hijack by a door opening (+)
while the ignition is on or by the speedometer trigger.
F19 Arm (-)
F19/1: The output (-) of Black/White wire is reverse
to the armed output (-) (Orange wire). That means,
when the Orange wire outputs signal (-), the
Black/White wire will not output signal (-), when the
Orange wire does not output signal (-), the
Black/White wire will output signal (-).
F19/2: Black/White wire will output signal (-) for
turbo timer.
F13 Transponder card
The transponder card is an additional upgrade
accessory.
F13/1 Turn off the transponder card detection.
F13/2 Turn on the transponder card detection. If the
transponder card is not found, the engine will be
immobilized.
F13/3 Turn on the transponder card detection and
anti-hijack will be activated automatically when the
transponder card is not detected.
F20 CH5 output
F20/1: The output (-) of Gray wire is reverse to the
armed output (-) (Orange wire).
F20/2: The Gray wire will output a signal (-) to trigger
a pager when the alarm system is triggered.
F14 Ignition warning in disarmed mode
In disarmed mode, when ignition is on, the ignition
icon ( ) will show on the LCD transmitter.
F21 CH6 output: two blue/black wires
Select between turbo timer and W-mode.
F21/1: output signal (-) for 20 seconds after
disarmed. This option is recommended to trigger
the headlight output.
F15 INST2 (-) extra input trigger
Select between an INST2 extra input (-) or a
speedometer input (-).
20
F21/2: output signal (-) for turbo timer according to
the time of the F1 setting.
F21/3/4/5: The channel will activate according to
the W-mode setting. Select among
1 start and stop by real time (according to the Wmode setting to start and stop);
2 start for 1 second by real time (according to the
w-mode setting to start for 1 second signal);
3 start for 1/0.5/1 sec by real time (according to
the w-mode setting start for 1 second and pause
for 0.5 second then a 1 second signal)
Before you begin the installation
* Read the INSTRUCTIONS!
F22 Window/sunroof closer
This option suits for vehicle with automatic
window/sunroof close function. Select for 10
seconds, 15 seconds, 22 seconds or 30 seconds
to close the window/sunroof.
Mounting ECU
Mount the ECU under the dash where it will be
difficult for a potential thief to locate the module,
and away from moving parts such as brake pedals,
etc.
F23 Passive arming
The system will arm automatically 30 seconds after
the car is parked and all doors are closed.
Antenna module
For optimum range and performance, the antenna
module should be located high up on the front
windshield glass. For example: behind the rearview
mirror.
* Always use a multi-meter when verifying vehicle
wiring.
* Before mounting the product, verify with the
customer's desired location for the valet switch and
LED.
* Always look before drilling. Make sure you will not
cause damage to vehicle hoses, electrical looms or
physical damage to vehicle.
F24 Door lock if passive arming on
All doors will lock while passive arming.
Note: Window tints or Films may decrease the range
of the system. The mounting surface for the antenna
should be clean and dry.
F25 STOP (-/+) function of door trigger
F25/1: no change to the door trigger
F25/2: door trigger (+) wire (violet) will be defined
not for door trigger, e.g. it can be defined as a
footbrake trigger (+).
F25/3: door trigger (-) wire (brown) will be defined
not for door trigger, e.g. it can be defined as a
footbrake trigger (-).
Mounting siren
Mount the siren in a suitable place under the hood,
away from hot and moving engine parts. Make sure
the siren cannot be accessed from underneath the
21
vehicle or through the grill. Face the siren down so
that water cannot accumulate inside the siren bell.
Protect wires running through the firewall using
either tape or split loom tubing.
* BLUE/ RED WIRE - INST2 input (-).
* YELLOW WIRE -- IGN1, +12V ignition input.
a. Connect to hood pin switch or trunk switch.
b. Connect to speed sensor of "VAZ" vehicle (F15.
F3).
Connect to a main ignition wire at the ignition switch
harness. This wire shows +12V when the ignition
is on and while cranking. The voltage must not drop
when the car is starting.
IGN1(+)
* RED WIRE -- +12V Battery input. Connect the red
Mounting shock sensor
Secure the shock sensor to the steering column,
thick wire harness or a dash brace, using a wire tie.
fused wire on the main harness to a constant +12V
source.
* BROWN WIRE -- Negative door trigger (-). Connect
Make sure that the adjustment screw is accessible
for later testing and adjustment.
to the door switch circuit wire that shows ground
when the door is open.
20-Pin main harness
* BLACK WIRE -- Ground input (-). Connect to a
solid chassis ground that is clean and free of paint
or dirt.
* WHITE WIRE --Parking lights output (+). Connect
to the vehicle's parking lights wire.
* VIOLET WIRE -- Positive door trigger (+). Connect
* ORANGE WIRE -- Armed output (-) 500mA.
Connect to a relay for optional circuit defeat (See
installation diagrams). The ORANGE wire provides
a ground 40 seconds when the unit is armed to
activate a fuel pump disable relay or other device
(i.e. window control module, etc.).
4-Pin White Connector A: Plug-in connector port
for 2-stage shock sensor.
Contact of additional relay to control
turbo timer mode for channel ARM (-),
CH6 or "TRIGGER" of channel CH2.
* GREEN / RED WIRE -- CH3 output (-) 1A. Please
refer to the System programming table F9.
* BLUE / BROWN WIRE - INST1 input (-). Connect
* GRAY WIRE - CH5 output (-) 500mA. (F20).
to hood pin switch or trunk switch. The BLUE /
BROWN wire provides a ground when the hood or
trunk opened.
* BLACK / WHITE WIRE - ARM (-) 500mA.
* BLUE / BLACK WIRE - CH6 output (-) 1A. ( F21).
* YELLOW / BLACK WIRE -- IGN2, +12V ignition
input. Connect to the wire going to the starter. The
voltage of this wire output can keep engine running
according to the Turbo timer.
22
Output ignition
wire from car
ignition lock
* GREEN / WHITE WIRE - CH4 output (-) 500mA.
* BLUE WIRE - CH2 output (-) 500mA. (F8).
Connect to the siren's red wire. Connect the siren's
black wire to ground.
Wire that
supplies+12 V
to car ignition lock
2-Pin Connector: Plug-in connector port for valet
switch. Mount switch in an area that is easily
accessible from the driver's seat. The switch should
be well hidden. It should be placed so passengers
or stored items (such as in a glove box or central
console cannot accidentally hit it.
IGN2(+)
to the door switch circuit wire that shows +12V when
the door is open. This type of door circuit is usually
found on Ford vehicles.
(F10).
* WHITE / BLACK WIRE -- Siren wire output 5A(+).
Ignition contact
of car ignition
lock
Plug in connectors
2-Pin Connector: Plug-in connector port for LED.
Mount LED in an area where it may be easily seen
from either side of the vehicle.
4-Pin White Connector B: Plug-in connector port
for optional ultrasonic sensor.
6-Pin door lock connector
* BLUE / WHITE WIRE -- Lock relay N/O (87).
* YELLOW WIRE -- Lock relay Common (30).
* GREEN WIRE -- Lock relay N/C (87a).
* ORANGE WIRE -- Unlock relay N/O (87).
* WHITE WIRE -- Unlock relay common (30).
* BLUE WIRE -- Unlock relay N/C (87a).
23
Door lock wiring diagrams
Optional relay wiring diagrams
ADDING ACTUATORS
NEGATIVE PULSE LOCK SYSTEM
L
UL
(-) DOOR LOCK
(-) DOOR UNLOCK
GREEN
NC
YELLOW
COM
BLUE/WHITE
GREEN
NC
YELLOW
COM
BLUE/WHITE
BLUE
NO
NC
WHITE
COM
ORANGE
NO
NO
BLUE
NC
WHITE
COM
ORANGE
NO
+12V
Hood / trunk pin switch relay wiring diagrams
POSITIVE PULSE LOCK SYSTEM
VACUUM LOCK SYSTEM
REVERSE POLARITY LOCK SYSTEM
VACUUM PUMP
UL
GREEN
NC
YELLOW
COM
BLUE/WHITE
BLUE
NO
NC
WHITE
COM
ORANGE
NO
GREEN
NC
YELLOW
COM
BLUE/WHITE
NO
BLUE
NC
WHITE
COM
ORANGE
NO
GREEN
NC
YELLOW
COM
BLUE/WHITE
CUT
BLUE
L
X
(+) DOOR UNLOCK
CUT
NO
COM
ORANGE
NO
Blue
V
NC
WHITE
X
UL
To hood / trunk
release
L
(+) DOOR LOCK
X
L
Hood / trunk
pin switch
CUT
UL
+12V
+12V
+12V
24
25
Wiring diagram
Troubleshooting
Fault
1. The continuous chirping of the siren cannot
be stopped by transmitter after the installation
of ECU.
Blue / Brown
Causes
The plug is improperly inserted.
The wire is improperly connected.
The transmitter does not match the ECU.
The siren is damaged.
The fuse of the ECU is broken
INST1(-)
White / Black
20
Blue / Red
Door trigger wire is not connected properly.
Door switch has problem.
The siren is damaged.
2. Parking lights do not flash after disarming
the system and opening the door, or the siren
does not chirp when the door is opened without
disarming.
5A
INST2(-)
3. When the car parks on roadside and armed,
there are false alarms by passing heavy
vehicles.
The sensitivity of the sensor is too high.
4. The central door lock does not work normally
or does not work at all.
Sensor (optional)
15A
Brown
Parking lights
7.5A
CH3 output (-)
Green / Red
Green / Red
Yellow
IGN2 (+)
Yellow / Black
CH6 output (-)
The siren is damaged.
The wire connection between the siren and ECU
has problem.
6. The siren chirps sharply in 10 seconds after
arming and the same situation happened after
disarming and re-arming it again.
The sensor is damaged.
The doors or trunk is not closed.
The door's pin switch has problem or wiring has
problem.
7. Transmitter is ineffective or the control
distance decreased significantly.
The installation location of the antenna is wrong.
The wiring of the antenna to ECU has problem.
Tall building, radio tower or high frequency
electromagnetic wave may affect the remote range.
Low power of the battery.
The frequency of the transmitter has been
changed.
The transmitter is broken or damaged.
Door trigger (+)
Black / White
IGN1 (+)
5. The siren does not chirp when the alarm
system is triggered.
Door trigger (-)
7.5A
Arm (-)
The motor of central lock is damaged.
The wiring of central lock system is wrong.
Fuse is broken.
Green / White
CH4 output (-)
CH2 output (-)
Blue
5A
Gray
Blue / Black
Blue / Black
26
CH5 output (-)
27
Warranty
Steelmate warranty card
I. The unit is warranted for a limited period from
the date of purchase. In the unlikely event of a
defect arising in this product when used in
accordance with the manufacturer's instructions,
the parts would be repaired or replaced free of
charge.
User:
Tel:
Vehicle Reg No.:
It is required to show warranty card when
making any warranty claims.
Product Model No.:
The model and serial number on unit must be
the same as the information on the warranty card.
Serial No.:
II. This warranty is non-transferable and is
automatically void if:
Date of Installation:
The original purchaser has not completed the
warranty card.
Name of the Retailer:
The unit's serial number is defaced, missing or
altered.
Signed by Retailer:
The unit has been modified or used in a manner
contrary to its intended purpose.
The unit has been damaged by accident,
unreasonable use, neglect, improper installation
or service.
III. The warranty does not cover damage to the
unit caused by installation or removal of the unit.
28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement