- No category
advertisement
Connectors
Cable
Inputs
Network
Weight
Marking
TECHNICAL DATA SHEET
Designation
Reference
FUNCTIONS
RS485 4ILT INTERFACE
1870130
05 - 10 - 2009 SDEV-FICA 32 R0
The RS485 4ILT Interface is a motor controller for multi ratio motorized projection screens.
It can control up to 4 Somfy ILT motors. Each motor can be set (no need to use the ILT setting tool) and controlled individually through the interface.
Up to 8 formats can be memorized depending ratio: 4:3, 16:9, 2,35:1 …
A group command (=all motors) is also available to raise or lower screens.
It can be interfaced with infrared remote controls (Somfy or universal IR remotes) or with a RS485 data line (the system integrator must know the specific commands).
The interface has a trigger input, to connect with a video projector’s trigger output:
Video-projector ON : Motors lowers (format # 1)
Video-projector OFF : Motors raises (format # 8)
TECHNICAL SPECIFICATIONS
Box Material
Color
Supply (universal)
Size
Protection factor against solid & splashproof
Nominal (= limits)
Frequency
Electrical protection
Consumption (max.)
Temperature range Storing
Working
ABS
Black
137 x 80 x 40 mm
IP 20
90-255 V
50-60 Hz
Class II product
65mA @ 90V to 30mA @ 255V
-30°C / + 80°C
0°C / + 60 °C
IR Sensor
ILT Motors
Trigger (video projector)
RS-485
Color
Lenght
Connection
1 x R J9 phone plug
4 x R J9 phone plug
1 x Phoenix Contact connector block 3,5mm 2-pins
1 x Phoenix Contact connector block 3,5mm 4-pins
Black
2 meters
Termination free cable (2 wires)
Built in
Trigger 0 to 30V
RS485 Physical Layer + SOMFY RS485 protocol
132 g (without power supply cable)
CE
DIMENSIONS
COMPATIBILITY
IR remote control :
SOMFY IRT 803, 8 channels (Ref: 1870010)
SOMFY IR 8, 8 channels (Ref: 1870132)
Universal IR remote controls
IR sensor :
SOMFY IR3 sensor (Ref: 9154205)
Motor :
SOMFY ILT ( /!\ It’s not possible to set, call or delete a format /!\ )
SOMFY ILT2
SOMFY Sonesse ILT2
Range 1
230V – 50Hz
Range 2
120V – 60Hz
ILT
ILT 2
Yes
Yes Yes
Range 6
230V – 60Hz
Yes
Sonesse ILT2 Yes Yes
Brand having video-projectors in their 2009 products range, with DC 12V trigger output :
BenQ
Epson
Infocus
Mitsubishi
Optoma
Panasonic
Sony
Viewsonic
Yes
Yes
WIRING
KIT
Kit components :
Installation guide
Product with integrated power cable
Minimum needed parts to set up the system :
SOMFY IR3 sensor + ILT data cable 2.5m (Ref : 9154205)
SOMFY 8 channels IR remote (Ref : 1870132)
DATA LINE COMMANDS
Overview
The following paragraph describes the RS485 protocol of SOMFY, which is used to communicate with the RS485
4ILT INTERFACE.
The RS485 protocol supports bi-directional communication between a host and the interface.
The term «Host» refers to the device initiating communication with the interface, usually a computer-based system.
RS485 communication standard
All signals on the physical link between devices should comply with EIA/TIA-485-A standard.
Recommended cable: Shielded, two twisted-pair type 22 - 24 AWG (120 Ω ).
Communication mode: half-duplex. Between two messages, leave 100 ms approx.
Each character is coded as follow:
Warning: Data bits shall be inverted
Message format
See the installation guide.
Message table
See the installation guide.
Development & Engineering Quality Business Unit
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project