Owner`s Manual - Accessories4less

Owner`s Manual - Accessories4less
Digital Sound Projector
Owner’s Manual
Read the supplied booklet “Quick Reference Guide” before using the unit.
English
CONTENTS
Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Preparing remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FEATURES
5
PLAYBACK
22
Basic operation for playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Enjoying sound based on your preference . . . . . . . . . . . . . . . . . . . . . . . . 23
Selecting a surround sound effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
What you can do with this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2-channel playback (stereo playback mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Mastering useful apps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Adjusting volume for each channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Controls and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Viewing audio information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Clear playback of human voices (CLEAR VOICE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11
Wireless playback of audio via Bluetooth connection . . . . . . . . . . . . . . 26
PREPARATIONS
General setup procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
a Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Listening to audio through Bluetooth speakers or headphones (transmitting) . . . . . . . . . . . . . . . . . . . . . . . 29
Listening to music from a Bluetooth device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Terminating Bluetooth connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Raising the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mounting the unit on a wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
b Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
c Connecting playback devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
d Other connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting an external subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wired network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
e Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
f Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NETWORKS
31
Connecting to a network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Wired network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connecting the unit to a wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connecting a mobile device to the unit directly (Wireless Direct) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Playing back music stored on media servers (PCs/NAS) . . . . . . . . . . . . 42
Media sharing setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Displaying the menu screen on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Playing music files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Selecting the language for menu display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Listening to Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Setting a surround sound effect for the installation position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operating the unit by TV’s remote control (HDMI control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Playback of Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Registering favorite Internet radio stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Playing back music with AirPlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Playback of iTunes/iPod music contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Playing back music stored on mobile devices . . . . . . . . . . . . . . . . . . . . . 47
Using a mobile device to play songs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
En
2
SETTINGS
48
APPENDIX
62
Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Setting the setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Setup menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
When surround effect is not enough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
How to install YRB-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Basic Knowledge of Surround Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
What is Surround Sound? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Operating a TV via the TV Remote Repeater function of the unit . . . 58
Updating the unit’s firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
What is a Digital Sound Projector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Using “Network Update” in the setup menu to update firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Updating firmware with connection of a USB flash drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Audio/video information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Yamaha’s Audio Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Initializing the unit’s settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Network information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Initializing basic unit settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Initializing network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Available signal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
En
3
About this manual
• In this manual, operations that can be performed using either the front panel keys or the remote control
are explained using the remote control.
•
indicates supplementary explanations for better use.
•
indicates precautions for use of the unit and its feature limitations.
Preparing remote control
Supplied accessories
Before connecting, make sure you have received all of the following items.
Before installing batteries or using the remote control, be sure to read battery and
remote control precautions in “Quick Reference Guide” (separate booklet).
YSP-1600
The unit
Installing the batteries
Supplied accessories
Remote control
Batteries
(AAA, R03, UM-4; x2)
Optical cable
(1.5 m (4.9 ft))
Peel off the protection sheet
before use.
Battery × 2
(AAA, R03, UM-4)
Accessories for mounting the unit on a wall
Template
Brackets (x2)
Screws (M4 x 12mm; x4)
ANTENNA / ANTENNE
MOUNTING TEMPLATE/GABARIT DE FIXATION
DRILL HERE / PERCER CIC
DRILL HERE / PERCER CIC
457mm (18” )
457mm (18 po)
ZR85910-1
Operation range
Owner’s Manual CD-ROM
Quick Reference Guide
MusicCast Setup Guide
Within 6 m (20 ft)
• The supplied optical cable may not be needed depending upon connections.
➤ Supplied accessories
En
4
FEATURES
What you can do with this unit
Sound beams are reflected off walls using unique
real surround sound formats and techniques,
allowing listeners to enjoy their preferred
acoustic environment.
• Enjoy realistic surround sound
with five surround modes: MOVIE,
MUSIC, SPORTS, GAME, TV
PROGRAM (CINEMA DSP)
• Clear playback of speech (dialog,
narration, etc.; CLEAR VOICE)
Wide variety of supported content
TV
•
•
•
•
. p. 23
. p. 25
Media server (PC/NAS)
Internet radio
AirPlay
Music stored on mobile
devices
.
.
.
.
p. 42
p. 43
p. 45
p. 47
Mastering
dedicated
apps
. p. 6
Sequential operation of a TV,
this unit, and BD/DVD player
(HDMI Control)
TV remote
control
. p. 20
HDMI
Control
Audio
Audio/
Video
Audio
Mobile
devices
Network contents
Control
Control
Plays back audio content
from Bluetooth® devices
The unit
Audio
HDMI Control
Audio/
Video
. p. 27
Mobile
devices
Listen to audio input to
the unit with Bluetooth
headphones or speakers
Audio
BD/DVD player
This unit’s
remote control
Bluetooth
headphones
FEATURES ➤
. p. 29
What you can do with this unit
En
5
Mastering useful apps
You can operate and program the unit, or play streaming services via the unit, by installing the free dedicated apps, MusicCast CONTROLLER and HOME THEATER CONTROLLER
(WLAN) on a mobile device such as a smartphone. For details, search for MusicCast CONTROLLER and HOME THEATER CONTROLLER (WLAN) on the App Store or Google Play.
MusicCast CONTROLLER
This app allows you to play distributed content and streaming services via the unit.
• In this manual, iOS and Android mobile devices are collectively referred to as “mobile devices”. The specific
type of mobile device is noted in explanations as needed.
MusicCast CONTROLLER capabilities
• Play songs stored on computers (servers)
• Select an Internet radio station
• Play music stored on mobile devices
• Distribute and receive audio between the unit and other Yamaha network A/V devices
See MusicCast Setup Guide for details.
HOME THEATER CONTROLLER (WLAN)
This app allows you to configure specific settings such as sound beams.
FEATURES ➤
What you can do with this unit
En
6
Controls and functions
Front panel
1
2
3
4
1 Indicators
Indicate the status of the unit (p. 8). The indicators will dim
automatically if no operations are performed for 5 seconds.
6
7
5 INPUT key
Select an audio input source (p. 22).
6 VOLUME (+/–) keys
Adjust the volume of the unit (p. 22).
• “Dimmer” can adjust the brightness of the front panel display
in the setup menu (p. 52).
5
• When the unit is turned off, this unit consumes a small amount of
power in order to search for HDMI signals or to receive infrared
signals from the remote control.
7 z key
Turn on/off the unit.
2 Dual built-in subwoofers
The built-in subwoofers are located in the top part of the unit.
3 Remote control sensor
Receive infrared signals from the remote control (p. 10).
Receive infrared signals from the TV remote control when the
TV Remote Repeater function is enabled (p. 58).
4 CONNECT key
Use to control the unit using the dedicated MusicCast
CONTROLLER app for mobile devices. See the MusicCast
Setup Guide for details.
FEATURES ➤ Controls and functions
En
7
Indicators
STATUS
TV
HDMI
ANALOG BLUETOOTH
1
1 STATUS indicator
Glows when surround playback is selected and turns off
when stereo playback is selected.
Glows red: The unit is off (with HDMI control or
network standby activated)
STATUS
Off: The unit is off
2 Audio input indicator
The corresponding indicator glows to show the input source
to which audio is selected.
4
Glows
HDMI
ANALOG
BLUETOOTH
NET
SURROUND
Glows when the MOVIE, MUSIC, SPORTS,
GAME, or TV PROGRAM key on the remote
control is pressed (surround playback).
SURROUND
Turns off when the STEREO key on the remote
control is pressed (stereo playback).
indicator
Glows when connected to a wireless network; turns off when
the connection is terminated (p. 32).
Example: when TV is selected
TV
3
3 SURROUND indicator
Glows green: The unit is on
STATUS
SURROUND
2
The STATUS indicator shows the unit’s power status.
STATUS
NET
5
4
5
❑ Other indications
In addition to indications explained 1–5, other indicators
on the front panel may glow or flash to indicate operation and
setting status.
In this manual, illustrations of the nine in-line indicators
are used for explanation.
: Off
: Glows
: Flashes
indicator
Glows blue when connected to a Bluetooth device; turns off
when the Bluetooth connection is terminated (p. 26).
Example: When the STATUS indicator flashes and the TV
indicator glows
Input source to be played back
TV
TV audio
HDMI
Audio from a device connected to the
HDMI IN jack
ANALOG
Audio from a device connected to the
ANALOG input jack
BLUETOOTH
Audio from a Bluetooth device
NET
Audio input via a network
FEATURES ➤ Controls and functions
En
8
Rear panel
4
5
6
7
8
9
0
HDMI
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
HDMI
IN
1
1 Power cable
For connecting to an AC wall outlet (p. 17).
2 TV Remote Repeater
Transmit signals from the TV’s remote control received by the
remote control sensor on the unit’s front panel to the TV
(p. 58).
3 Antenna
Raise the antenna after the unit is installed (p. 13).
4 HDMI IN jack
For connecting an HDMI-compatible playback device such
as a BD/DVD player, a satellite and cable TV tuner, and a
game console (p. 16).
2
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
3
5 HDMI OUT (ARC) jack
For connecting to an HDMI-compatible TV and outputting
video/audio signals (p. 15).
0 UPDATE ONLY jack
Use to update this unit’s firmware (p. 60).
6 NETWORK jack
For connecting to a network with a network cable (p. 17).
7 TV (digital optical) jack
For connecting to a playback device equipped with a digital
optical audio output jack (p. 15).
8 ANALOG jack
For connecting an external device with a 3.5 mm RCA stereo
cable (p. 16).
9 SUBWOOFER OUT jack
For connecting an external subwoofer (p. 17).
FEATURES ➤ Controls and functions
En
9
Remote control
1 Input selector keys
Select an audio input source to be played back (p. 22).
Infrared signal transmitter
8
1
9
2
3
TV
HDMI
Device connected via the HDMI IN jack
ANALOG
Device connected via the ANALOG input
jack
0 CH LEVEL key
BLUETOOTH
Bluetooth device
a STEREO key
NET
Audio last input via a network
2 Surround mode key
Choose a surround playback mode from MOVIE, MUSIC,
SPORTS, GAME, TV PROGRAM (p. 23).
Turns the CLEAR VOICE function on or off (p. 25).
4 S/T/W/X keys, ENTER key
Change the setting (p. 48).
5 SETUP key
4
Displays the setup menu (p. 48).
5
c
d
6
e
Turn on/off the unit (p. 22).
9 NET RADIO (1–3) keys
TV
3 CLEAR VOICE key
0
a
b
8 z key
Register and play streaming services such as Internet radio
stations via the unit (p. 43).
Adjust the volume balance during playback (p. 24).
Switch to stereo playback mode (p. 23).
b INFO key
Use the indicator on the front panel to show information for
audio currently playing (p. 24).
c RETURN key
Return to the previous menu screen.
d MUTE key
Mute the sound (p. 22).
e VOLUME (+/–) key
Adjust the volume of the unit (p. 22).
6 SUBWOOFER (+/–) key
Adjust the volume of the subwoofer (p. 22).
7 POSITION (L/C/R) keys
For optimum surround sound effect, select a preset position
mode according to where the unit is installed (p. 19).
7
FEATURES ➤ Controls and functions
En
10
PREPARATIONS
General setup procedure
Position the unit to achieve the optimal surround sound effects. The unit can also be mounted
on a wall.
1
Installation (p. 12)
2
Connecting a TV (p. 15)
Connect a TV to the unit.
3
Connecting playback devices (p. 16)
Connect video devices (such as BD/DVD players) to the unit.
4
Other connections (p. 17)
5
Connecting the power cable (p. 17)
After all the connections are complete, plug in the power cable.
6
Initial settings (p. 18)
Specify unit settings before use to adjust surround sound effects based on position and
conditions.
Raise the wireless antenna in preparation for network connection using a wireless router
(access point).
Connect an external subwoofer.
Use a network cable to connect the unit to a router in preparation for wired network connection.
This completes all the preparations. Enjoy playing movies, music and other content with the unit!
• See “NETWORKS” (p. 31) for information regarding network connection and audio playback via a network.
PREPARATIONS
➤ General setup procedure
En
11
1 2 3 4 5 6
a Installation
Place the unit on a flat surface. When installing this unit on a rack behind which there is limited space, for example, it may be easier to connect external devices to this unit first. See
pages 15 to 17 for information regarding the connection of external devices.
Notes
• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.
• The unit’s speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the unit.
• Do not stack the unit directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.
Recommended place for installation
• Do not install the unit near a corner of the
room.
• The unit can be mounted on a wall (p. 14)
• When raising the antenna (p. 13), position
the unit so that the antenna does not
obstruct the TV screen.
• The listening position (such as sofa, etc.)
should be located at the front of the unit.
Position the unit and TV so that they are separated
by at least 5 cm (2").
Use the TV Remote Repeater function if the unit
obstructs the remote control sensor on the TV
(p. 58).
To achieve the optimal surround sound
effects, be sure that obstacles such as
furniture may not obstruct the path of
sound beams (p. 13).
• The distance between the listening position
and the unit should be more than 2 m (6.6 ft).
PREPARATIONS
➤ a Installation
En
12
1 2 3 4 5 6
❑ Unit installation position and surround sound effects
Raising the antenna
The unit achieves surround sound by reflecting sound beams off walls.
Raise the antenna on the rear panel of the unit when connecting a wireless router
(access point) to use a network.
Hold the base of the
antenna while raising it
to its upright position.
Effective surround effect may not be achieved in the following environment.
• Sound beams are blocked by obstacles such as furniture.
• The room size is not within the following dimensions;
Width: 3 meters to 7 meters (9.8 ft to 23 ft)
Depth: 3 meters to 7 meters (9.8 ft to 23 ft)
Height: 2 meters to 3.5 meters (6.6 ft to 11.5 ft)
• Listening position is too close to the unit.
• Do not apply excessive force on the antenna. Doing so may damage it.
• Be sure to check the direction in which the antenna moves, and angle it in the proper direction.
• The unit is installed too close to the left or right wall.
• Do not remove the antenna.
• The unit is installed in the corner of the room.
• There is no wall for reflecting sound beam on the path of the sound beams.
• For details on the wireless connection, refer to p. 32.
• The optimum surround sound effect is achieved by setting a position according to the installation position of
the unit. For details, refer to “Setting a surround sound effect for the installation position” (p. 19).
PREPARATIONS
➤ a Installation
En
13
1 2 3 4 5 6
Mounting the unit on a wall
The unit can be mounted on a wall.
If the antenna will be used (p. 13), raise it before
mounting the unit on a wall.
1
Attach the mounting template on a wall
and mark for the screw holes.
3
Tapes or
thumbtacks
Position the
bracket so that
the protrusions
on the side of the
bracket fit into
the grooves on
the unit.
Mounting template (supplied)
ANTENNA / ANTENNE
DRILL HERE / PERCER CIC
MOUNTING TEMPLATE/GABARIT DE FIXATION
DRILL HERE / PERCER CIC
457mm (18” )
457mm (18 po)
Use the screws to attach the brackets
(both supplied).
ZR85910-1
Screw
holes
2
Remove the mounting template from the
wall and install the commercially available
screws at the marks on the wall.
4
ANTENNA / ANTENNE
• When installing the unit on a wall, all installation work must be
performed by a qualified contractor or dealer. The customer must
never attempt to perform this installation work. Improper or
inadequate installation could cause the unit to fall, resulting in
personal injury.
• To prevent the unit from falling, attach it to a wall constructed of
drywall (plasterboard).
• Make sure you use commercially available screws that can support
the weight of the installation (in step 2). Using clamps other than
specified screws, such as short screws, nails, and two-sided tape,
may cause the unit to fall.
DRILL HERE / PERCER CIC
MOUNTING TEMPLATE/GABARIT DE FIXATION
DRILL HERE / PERCER CIC
457mm (18” )
457mm (18 po)
Screws
(supplied)
Brackets
(supplied)
Hang the unit on the screws.
ZR85910-1
ANTENNA / ANTENNE
MOUNTING TEMPLATE/GABARIT DE FIXATION
7 to 9 mm
(1/4" to 3/8")
DRILL HERE / PERCER CIC
DRILL HERE / PERCER CIC
457mm (18” )
457mm (18 po)
4 mm (#8)
20 mm (3/4") or more
ZR85910-1
Bracket
mounting
holes
2 to 4 mm
(1/16" to 3/16")
• Fix the cables in place where they will not become loose. If your foot
or hand accidentally gets caught on a loose cable, the unit may fall.
• Check that the unit is fixed securely after the installation. Yamaha
will bear no responsibility for any accidents caused by improper
installations.
• Do not lean on the unit or apply excessive force to the top of the
unit. Doing so may cause the unit to fall.
PREPARATIONS
➤ a Installation
En
14
1 2 3 4 5 6
b Connecting a TV
Connect a TV to the unit so that video input to the unit can be output to the TV. You can also enjoy playback of TV audio on the unit.
• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is recommended to prevent degradation of signal quality.
• For playback of 3D and 4K video content, use a high-speed HDMI cable.
TVs that support Audio Return Channel (ARC)
Connect the TV to the unit with an HDMI cable (not supplied).
TVs that do not support Audio Return Channel (ARC)
Connect the TV to the unit with an HDMI cable (not supplied) and an optical cable.
HDMI OUT (ARC) jack
• This unit supports HDCP version 2.2, a copy protection technology. To enjoy playback of 4K video, connect
the unit to the HDMI IN jack (one compatible with HDCP 2.2) on an HDCP 2.2-compliant TV.
HDMI input
HDMI
HDMI
HDMI
HDMI
OUT(ARC)
HDMI OUT (ARC) jack
ARC-compatible HDMI input
HDMI
(ARC)
HDMI
HDMI
IN
HDMI
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
HDMI
OUT(ARC)
The unit
(rear)
OPTICAL
O
TV
HDMI
IN
TV
O
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
The unit (rear)
Audio output
(digital optical)
TV jack
TV
1. Remove the cap
When connecting a TV that supports Audio Return Channel (ARC), enable the HDMI
control function (p. 51).
2. Check the direction of
the plug
Audio Return Channel (ARC)
ARC enables input and output of audio signals via a single HDMI cable. If the TV supports ARC, audio
signals from the TV can be input to this unit via the same HDMI cable used to output video signals from
this unit to the TV.
• Use an ARC-compatible HDMI cable.
• If the TV has no optical jack
Use a 3.5 mm stereo mini plug cable to connect the unit to the TV via the ANALOG input jack on the unit
and the audio output jack on the TV. TV audio can be played through this unit by switching input to
ANALOG using the ANALOG key on the remote control.
PREPARATIONS
➤ b Connecting a TV
En
15
1 2 3 4 5 6
c Connecting playback devices
Connect video devices such as BD/DVD players, set-top boxes (STBs) and game consoles to the unit. Depending on the video/audio output jacks available on your video device,
choose one of the following connections. We recommend using an HDMI connection if the video device has an HDMI output jack.
HDMI connection
Analog connection
Connect a video device to the unit with an HDMI cable (not supplied).
HDMI IN jack
Connect a video device to this unit via a 3.5 mm stereo mini plug cable (not supplied).
Next, connect the video device’s video output to the TV’s video input.
HDMI output
HDMI
ANALOG jack
3.5 mm stereo mini
plug cable
HDMI
HDMI
IN
Audio output
(analog)
ANALOG
HDMI
IN
Video device
HDMI
To video
output jack
HDMI
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
Video device
The unit (rear)
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
To video
input jack
The unit (rear)
TV audio can be played through this unit by switching input to HDMI using the HDMI
key on the remote control.
TV
• Once the HDMI control function has been activated (p. 20), video and audio content from playback devices
can be output from the TV even when this unit is off (HDMI signal pass-through).
• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is
recommended to prevent degradation of signal quality.
• For playback of 3D and 4K video content, use a high-speed HDMI cable.
TV audio can be played through this unit by switching input to ANALOG using the
ANALOG key on the remote control.
• If the video device has an HDCP 2.2-compliant HDMI output jack, connect the unit to that jack.
• Audio from the video device can be input via the TV (digital optical) jack, not via the HDMI IN jack. Use an
optical cable to connect the video device to the unit via the digital optical output jack on the video device
and the TV jack on the unit. If the video device is connected to the unit in this way, change the “HDMI”
setting in the setup menu from “Audio Assign” to “Optical”.
PREPARATIONS
➤ c Connecting playback devices
En
16
1 2 3 4 5 6
d Other connections
e Connecting the power cable
After all the connections are complete, plug in the power cable.
Connecting an external subwoofer
The unit has built-in subwoofers. However, you can connect an external subwoofer to
enhance low-frequency sounds. Connect a subwoofer via the SUBWOOFER OUT jack
on this unit.
The unit (rear)
SUBWOOFER OUT jack
SUBWOOFER OUT
Subwoofer pin cable
(not supplied)
INPUT
To an AC wall outlet
HDMI
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
The unit (rear)
Subwoofer
• Use an external subwoofer with a built-in amplifier.
Wired network connections
For a wired connection, connect one end of the network cable to the NETWORK jack on
the rear panel of the unit and the other end to a router. For details, refer to
“NETWORKS” (p. 31).
PREPARATIONS
➤ d Other connections
En
17
1 2 3 4 5 6
f Initial settings
Displaying the menu screen on the TV
Visual operation of this unit is
possible by displaying its menu
screen on the TV.
TV remote control (example)
Initial screen display
Turn on the unit and the TV, and
then use the input button on the
TV’s remote control to switch input
so that video input from this unit is
displayed.
Switch
input
sources
When the unit is turned on for the first time after purchase, the
screen below will be displayed and the
indicator on the front
panel will flash slowly.
Share
Y
(
n
u
l
When this unit and the TV are
connected as shown below,
select “HDMI 1”.
o
W
e
s
a
u
i
t
i
t
w
n
e
c
F
o
g
r
an
i)
rk
a
.
s
s
w
d
Wi-Fi
h
e
i
e
a
t
t
v
Settings
re the wireless
tings of the
h Sound Projector
ice with iOS7 or
[ENTER]:Start
[RETURN]:Cancel
[
]:OSD Language
HDMI
HDMI
RETURN
HDMI
SETUP
Flashes slowly
1
OUT(ARC)
2
3
HDMI INPUT
While this screen is displayed, an iOS device (such as an
iPhone) can be used to easily connect the unit to a wireless
network. See the Quick Reference Guide.
If you will not use an iOS device to connect to a wireless
network, press the RETURN key.
HDMI
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
The unit (rear)
TV
• You can use this function to connect to a wireless network at any time by
selecting “Share Wi-Fi Settings (iOS)” from the setup menu. However, be
aware that if a different wireless network, or a Bluetooth device, has already
been configured, doing so will erase any previous settings.
The menu display
The menu is displayed on the TV screen when the SETUP key is
pressed. When the TV is receiving HDMI signals, the menu is
superimposed over video content. Press the SETUP key twice to
cancel menu display.
• This screen will not be displayed and the
indicator will not flash if the unit
is connected to a router via its NETWORK jack (wired connection).
Setup Menu
Channel Level
Sound
Dynamic Range
HDMI
Audio Delay
Function
Information
PREPARATIONS
➤ f Initial settings
En
18
1 2 3 4 5 6
Selecting the language for menu display
1
2
3
Turn the unit and TV on.
Switch the TV’s input to display video input from this unit (p. 18).
Press and hold the SETUP key until the “OSD Language” menu
appears on the TV.
Setting a surround sound effect for the installation
position
The surround sound is achieved by reflecting the sound beams off walls as shown in
the illustration below. For optimum surround effect, turn on the unit and select the
POSITION key according to the installation position of the unit.
1
Hold down the POSITION key that corresponds to the installation
position of the unit for more than 3 seconds.
The indicators on the front panel flash according to the set position.
OSD Language
Left
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
NEDERLANDS
РУССКИЙ
SVENSKA
TÜRK
Center
Right
L (Left)
When the menu is not displayed
• Confirm the following cases.
Left side of room
– The HDMI input jack of your TV and the HDMI OUT (ARC) jack of the unit are connected.
– The input of your TV is set to “HDMI 1” (example).
4
Use the S/T key to select the desired language and press the
ENTER key.
Settings
C (Center)
(default setting)
, ENGLISH (default), DEUTSCH, FRANÇAIS, ESPAÑOL, ITALIANO, NEDERLANDS,
РУССКИЙ, SVENSKA, TÜRK
5
Center of room
Press the SETUP key to exit the setup menu.
R (Right)
Right side of room
PREPARATIONS
➤ f Initial settings
En
19
1 2 3 4 5 6
Operating the unit by TV’s remote control (HDMI control)
With some TVs, navigating this unit’s menus displayed on the TV can be controlled.
What is the HDMI control function?
HDMI Control allows you to operate external devices via HDMI. If you connect a TV that
supports HDMI Control to the unit with an HDMI cable, you can control the unit (such as
power and volume) with TV remote control operations. You can also control playback
devices (such as HDMI Control-compatible BD/DVD players) connected to the unit with
an HDMI cable.
• Even if your TV supports the HDMI control function, some functions may not be available. For details, refer
to the manual supplied with your TV.
• We suggest using devices (TV, BD/DVD player, etc.) from the same manufacturer.
Coordinated functions via the TV remote control
Remote control of TV (Example)
1. Turn on/off
Both the TV and this unit turn on/off at the same time.
2. Switch input sources
• The input source for this unit switches accordingly when the TV’s
input source is switched. The input source for this unit also switches
when a BD/DVD player is selected as the input source from the TV’s
menu display.
• The input source can be switched while this unit is turned off.
3. Control volume
This unit’s volume can be adjusted when the TV’s audio
output is set to the external device.
4. Switch the audio output device (TV or this unit)
First, try the operations described above with your TV’s remote control. If you are able
to perform these operations, you may continue operating this unit with your TV’s remote
control. The HDMI control function can be used with some HDMI devices by simply
activating the function. If you are not able to perform these operations, configure HDMI
control settings (p. 21).
PREPARATIONS
➤ f Initial settings
En
20
1 2 3 4 5 6
Setting the HDMI control function
1
2
Turn on the unit, TV, and playback devices.
If devices are not coordinated
Be sure that all devices are correctly connected to this unit, and
that settings are properly configured as described below.
– “HDMI Control” (p. 51) is set to “On” in the setup menu.
Activate the HDMI control function on the unit, TV,
and playback devices such as BD/DVD players that
support this function.
– The HDMI control function is enabled on the TV.
The example of TV settings
• From the setup menu on your TV, select “Link setting” “HDMI control setting”, then set a setting such as “HDMI
control function” to “ON”.
For this unit, be sure that “HDMI Control” is set to “On”
(default; p. 51).
For playback devices, refer to the instructions supplied with
each device.
HDMI
• Set audio output to any option other than TV.
3
Turn off the main power of the TV and then turn off
the unit and playback devices.
4
Turn on the unit and playback devices and then turn
on the TV.
5
– Disconnect the power cable of the unit and external devices
connected to the unit via HDMI cable. Plug them in again after
about 30 seconds.
Switch the TV input to display the video from the
unit.
– If devices fail to coordinate after ANALOG is input, repeat
steps 5 and 6 under “Setting the HDMI control function”.
6
Press the HDMI key to select HDMI input, and check
that video from the playback device is properly
displayed.
– Turn off this unit and the TV, and then turn them back on again.
HDMI
Glows (green)
7
If devices fail to coordinate even after the settings described
above have been applied correctly:
Check that the unit is properly coordinated with the
TV by turning off the TV or adjusting the TV volume
with the TV remote control.
Changing the connection method and
connected devices
When the connected devices and jacks are changed, configure the
settings again with the following procedure.
1
Disable the HDMI control function of the TV and BD/
DVD player, turn off all connected devices, and
change the connections.
2
Follow steps 1 to 7 of “Setting the HDMI control
function”.
PREPARATIONS
➤ f Initial settings
En
21
PLAYBACK
Basic operation for playback
1
2
Input
selector
keys
3
Subwoofer volume display
Press the z key to turn on this unit.
The lighted indicator moves to the right when the volume is turned up,
and to the left when the volume is turned down.
Turn on devices (TV, BD/DVD player, game console,
etc.) connected to this unit.
Volume down (–)
Select a device by pressing the input selector key
corresponding to the connection of external
devices.
Volume up (+)
• When audio is output from both TV speaker and this unit,
mute the TV sound.
Press the HDMI key to play audio/video content from a BD/
DVD player connected via the HDMI IN jack.
• When sound input to HDMI IN jack is output from the TV,
the volume level does not change even if you press the
VOLUME (+/–) key or the MUTE key.
Indicator on the front panel
To mute the audio output
HDMI
To mute the sound, press the MUTE key.
Glows
SUBWOOFER
(+/-)
VOLUME
(+/-)
For playback from a Bluetooth device, refer to p. 26. For
audio playback via a network, refer to p. 42 to 47.
4
To resume the volume, press the MUTE key again or press
the VOLUME (+/–) key.
Play back a device selected in step 3.
• The subwoofer volume can be adjusted separately from the whole volume.
MUTE
• When listening to audio or watching video from a playback device
connected to the TV, select the device as the TV's input source.
5
Press the VOLUME (+/–) key to adjust the volume.
Press the SUBWOOFER (+/–) key to adjust the
volume of the subwoofer.
When the volume is adjusted, indicators on the front panel
indicate volume level.
• Lowering the subwoofer volume is recommended at night.
6
Select from surround playback or stereo playback
mode, and configure sound setting according to
your preferences (p. 23).
Press the z key to turn off this unit after use.
Volume display
The number of lighted indicators increases when the volume is turned
up, and decreases when the volume is turned down.
Volume down (–)
Volume up (+)
PLAYBACK
➤ Basic operation for playback
En
22
Enjoying sound based on your preference
Selecting a surround sound effect
2-channel playback (stereo playback mode)
Select the surround mode to enjoy realistic surround effects that
closely resemble a movie theater, the middle of a music concert, or
a sports field event, by Yamaha’s sound field program, “CINEMA
DSP.” You can select a surround mode that best suits the source
from MOVIE, MUSIC, SPORTS, GAME, or TV PROGRAM.
The front channels are the primary channel sources for output of
stereo sound.
1
Surround
mode keys
Press one of the surround mode keys (MOVIE,
MUSIC, SPORTS, GAME, or TV PROGRAM).
1
Press the STEREO key to switch to stereo playback
mode.
Indicator on the front panel
SURROUND
Off
Indicator on the front panel
SURROUND
Glows
STEREO
INFO
Surround mode
The features of surround modes are described below.
Select the surround mode that best suits the playback source and
your personal taste.
Sound field
program
Features
MOVIE
Creates a broad and expansive cinematic space. With
Dolby or DTS surround effects, this program enriches
your cinematic experience.
MUSIC
Creates the palpable excitement, as if you were standing
at the front center of a live concert hall event.
SPORTS
Creates the realistic atmosphere of a live sports event or
talk show.
GAME
Enjoy three-dimensional sound effects with computer or
video games.
TV PROGRAM Creates optimum surround sound for TV programs.
• When the source is a 2-channel stereo signal, the sound is played back as
surround sound.
PLAYBACK ➤ Enjoying sound based on your preference
En
23
Adjusting volume for each channel
3
Adjust the volume of playback for each channel (audio in each
direction) so that sounds are evenly distributed in their respective
directions.
Press the S/T key to adjust the volume.
Display while volume is adjusted
The lighted indicator moves to the right when the volume is turned up,
and to the left when the volume is turned down.
Volume down (T)
• Refer to “Channel Level” (p. 50) when adjusting the volume of each channel with
the test sound.
1
Hold down the CH LEVEL key for more than 3
seconds.
Volume up (S)
Example of volume balance
• If you have problems hearing words: Select C (center) to increase the level.
2
CH LEVEL
INFO
Press the CH LEVEL key to select adjustable
channel from the followings.
The output channel changes as follows each time the CH
LEVEL key is pressed.
When the sound is not like surround sound: Select SL (surround left) and SR
(surround right) to increase the level.
• The volume of the subwoofer also can be adjusted by using the SUBWOOFER (+/
–) key.
• When the position setting is changed (p. 19), the channel level setting will be
overwritten.
Indicators on the front panel
Viewing audio information
Front (left)
/
Information regarding audio currently playing can be viewed.
Center
SUBWOOFER
(+/-)
1
Press the INFO key.
The following information regarding audio currently playing
is displayed via indicators on the front panel while the INFO
key is held down.
Front (right)
Surround (right)
1
2
3
4
5
a Audio from a TV that supports ARC is currently being
input to the unit via the HDMI cable
Surround (left)
b Input signal: DTS
c Input signal: Dolby Digital
Subwoofer
d Dolby Pro Logic II is currently in use (2-channel audio
signal is input)
Returns to Front (left)
e CLEAR VOICE is enabled (p. 25)
• Subwoofer volume can only be adjusted in stereo playback mode (p. 23).
PLAYBACK ➤ Enjoying sound based on your preference
En
24
Clear playback of human voices
(CLEAR VOICE)
Human voices, such as lines in movies and TV shows, or news and
sports commentary, are played back very clearly.
1
Press the CLEAR VOICE key to turn on the CLEAR
VOICE function.
Indicators on the front panel
Flashes three times and then turns off
Press the key again to turn off the function.
CLEAR
VOICE
Flashes once and then turns off
PLAYBACK ➤ Enjoying sound based on your preference
En
25
Wireless playback of audio via Bluetooth connection
You can receive and play audio from a Bluetooth device, such as a mobile device or digital music player, over a wireless connection. Yamaha’s exclusive Compressed Music
Enhancer technology improves sound quality characteristics for the richness and depth of original audio before it is compressed.
You can also transmit audio input to the unit to Bluetooth speakers or headphones.
See documentation supplied with your Bluetooth device for more information.
Receive and play audio with the unit
Perform the following steps on the Bluetooth device to be connected.
For the first Bluetooth connection
For subsequent Bluetooth connection
Bluetooth device
(such as a mobile
device)
Pair the unit and Bluetooth device
Transmit and play audio from the unit
When connecting to a Bluetooth
device for the first time, “pairing”
between the device and unit is
required. Pairing is required for
connecting a Bluetooth device for the
first time.
Bluetooth speakers/
headphones
Connect Bluetooth device and play back
• Audio cannot be received by the unit from mobile devices and the like, and transmitted to speakers or
headphones at the same time.
• “Bluetooth” in the setup menu must be set to “On” (default; p. 57) to use Bluetooth functions.
PLAYBACK
➤ Wireless playback of audio via Bluetooth connection
En
26
Listening to music from a Bluetooth device
Pairing a Bluetooth device with the unit
1
4
Play back a song on the Bluetooth device.
Press the BLUETOOTH key on the remote control.
Bluetooth is selected as the input.
BLUETOOTH
Glows
BLUETOOTH
• If you are unable to select Bluetooth as an input source, be sure that the
following settings have been applied.
• The unit can be paired with up to 20 Bluetooth devices for receiving and
transmitting audio. If a new device is successfully paired with the unit after 20
other devices have already been paired, the device with the earliest connecting
date will have been unpaired to make room for the new device.
– “Bluetooth” in the setup menu is set to “On” (p. 57)
– “Transmission” in the setup menu is set to “Off” (p. 57)
2
3
• Perform pairing with the Bluetooth device and unit within 10 m (33 ft) of each
other.
Turn on the Bluetooth device to be paired, and
perform pairing.
• If a Bluetooth device has been connected before, the unit will connect to the last
connected device when the BLUETOOTH key is pressed with step 1. Terminate
this connection to pair a new device.
The operation varies depending on the device. Refer to the
instruction manual supplied with the device.
• Refer to “Bluetooth” (p. 64) in “Troubleshooting” if paring is not possible.
Select “YSP-1600” in the Bluetooth device list on
the device.
If a passkey (PIN) is required, enter the number “0000”.
PIN 0 0 0 0
YSP-1600
1
4
7
2
5
8
0
3
6
9
When pairing is completed,
or a completion message
appears on the Bluetooth device.
The
indicator on the unit’s front panel flashes while the
unit and Bluetooth device are being paired, and glows
steadily when pairing is complete.
PLAYBACK
➤ Wireless playback of audio via Bluetooth connection
En
27
Playing back audio from a Bluetooth device
on the unit
1
• Perform Bluetooth connection with the device and unit within 10 m (33 ft) of each
other.
• Adjust the volume level of the Bluetooth device as required.
Press the BLUETOOTH key on the remote control
when the unit is turned on.
• If a Bluetooth device has been connected before, the unit will connect to the last
connected device when the BLUETOOTH key is pressed with step 1. Terminate
this connection to connect to a different Bluetooth device.
Bluetooth is selected as the input.
• Setting “Network Standby” in the setup menu to “On” allows the unit to be turned
on and off with Bluetooth device operations.
BLUETOOTH
Terminating Bluetooth connection
Glows
Bluetooth connection is terminated in the following cases.
BLUETOOTH
• If you are unable to select Bluetooth as an input source, be sure that the
following settings have been applied.
– “Bluetooth” in the setup menu is set to “On” (p. 57)
The
indicator on the unit’s front panel turns off when the
connection is terminated.
• The Bluetooth device is turned off.
• The BLUETOOTH key is pressed for more than 3 seconds.
– “Transmission” in the setup menu is set to “Off” (p. 57)
• The unit is turned off.
2
Turn on the Bluetooth device.
Flashes
Connecting
Glows steadily
Connection established
3
Select “YSP-1600” in the Bluetooth device list on
the device.
4
Play back a song on the Bluetooth device.
PLAYBACK
➤ Wireless playback of audio via Bluetooth connection
En
28
Listening to audio through Bluetooth speakers or headphones (transmitting)
Pairing a Bluetooth device with the unit
Input
selector
keys
/
ENTER
1
2
Turn on the Bluetooth device.
3
Press the SETUP key twice.
Use the S/T keys to select a Bluetooth device, and
then press the ENTER key.
Device
Select the input source (other than BLUETOOTH)
with the input selector keys.
The setup menu is displayed on the TV screen.
▲
A
F
a
f
▼
B
G
b
g
C
H
c
h
D
I
d
i
E
J
e
j
Search
1
2
3
4
[ENTER]:Confirm
[RETURN]:Cancel
4
Use the S/T keys to select “Bluetooth”, and then
press the ENTER key.
5
Use the S/T keys to select “Transmission”, and
then press the ENTER key.
6
Use the S/T keys to select “On”, and then press
the ENTER key.
7
Use the S/T keys to select “Device Search”, and
then press the ENTER key.
SETUP
8
When a connection has been established (the device has
been paired with the unit), “Completed” will be displayed on
the TV screen.
The
indicator on the unit’s front panel flashes while the
unit and Bluetooth device are being paired, and glows
steadily when pairing is complete.
• A Bluetooth device that has been assigned a passkey (PIN) other than “0000”
cannot be connected to the unit.
• The unit cannot connect to a Bluetooth device if “Bluetooth” in the setup menu is
not set to “On” (p. 57).
• Perform pairing with the Bluetooth device and unit within 10 m (33 ft) of each
other.
• The unit can be paired with up to 20 Bluetooth devices for receiving and
transmitting audio. If a new device is successfully paired with the unit after 20
other devices have already been paired, the device with the earliest connecting
date will have been unpaired to make room for the new device.
• If a Bluetooth device has been connected before, the unit will connect to the last
connected device when the input source is selected in step 2. Terminate this
connection to pair a new device.
• “Not found” is displayed on the screen with step 8 when the unit cannot recognize
the name of the device.
• Refer to “Bluetooth” (p. 64) in “Troubleshooting” if paring is not possible.
PLAYBACK
➤ Wireless playback of audio via Bluetooth connection
En
29
Terminating Bluetooth connection
Playing back audio input from the unit
through Bluetooth speakers or
headphones
Bluetooth connection is terminated in the following cases.
The
indicator on the unit’s front panel turns off when the
connection is terminated.
• The connection is terminated from the Bluetooth device, or
the Bluetooth device is turned off.
• Be sure that “Transmission” in the setup menu is set to “On” (p. 57).
• Connection to a Bluetooth device is not possible during playback using AirPlay
(p. 45).
• “Transmission” in the setup menu is set to “Off”.
• The unit is turned off.
Input
selector
keys
1
2
Turn on the Bluetooth device.
Select the input source (other than BLUETOOTH)
with the input selector keys.
If a Bluetooth device has been connected before, the unit
will connect to the last connected device. Proceed to step
4.
To connect to a different device, proceed to step 3.
3
Follow steps 3 through 8 under “Pairing a Bluetooth
device with the unit” to pair the device with the unit.
When a connection has been established (the device has
been paired with the unit), “Completed” will be displayed on
the TV screen.
The
indicator on the unit’s front panel flashes while the
unit and Bluetooth device are being paired, and glows
steadily when pairing is complete.
4
Audio from the input source will play.
• Perform Bluetooth connection with the device and unit within 10 m (33 ft) of each
other.
• Adjust Bluetooth device volume as needed.
• Audio will also be output from the unit.
PLAYBACK
➤ Wireless playback of audio via Bluetooth connection
En
30
NETWORKS
Connecting to a network
You can choose between wired network connection and wireless network connection (p. 32) depending upon your network environment.
Network connection allows you to listen to Internet radio stations and play music files with AirPlay or your computer (media service) via this unit. You can operate the unit with a mobile
device to which the MusicCast CONTROLLER app has been installed, allowing you to enjoy listening to a variety of audio sources via this unit.
Wired network connections
• Some security software installed on your computer, or network device settings (such as a firewall), may
block the unit’s access to your computer or Internet radio stations. Should this occur, change security
software and/or network device settings.
To use a wired network connection, connect the unit to a router via an STP network
cable (category 5 or higher straight cable; not supplied).
• A network connection cannot be established if the MAC address filter on your router is enabled. Check your
router’s settings.
Network Attached Storage
(NAS)
• To configure your router’s subnet mask manually, apply the same subnet used by this unit to all devices.
• Use of a broadband connection is recommended when using Internet services.
Internet
• If your router supports DHCP, network settings for the unit need not be configured. Network parameters
(such as the IP address) will be assigned automatically. If your router does not support DHCP, or if you
prefer to configure network parameters manually, you must configure network settings yourself (p. 54).
• You can verify that network parameters (such as the IP address) have been properly assigned to the unit by
selecting “Information” (p. 54) from the setup menu.
WAN
LAN
Modem
• See our website for more information on the MusicCast CONTROLLER app.
PC
Network cable
Router
Mobile device
NETWORK
HDMI
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
The unit (rear)
• If the unit is already connected to a wireless network and you would like to switch to a wired connection,
change “Network” in the setup menu to “Wired”.
NETWORKS ➤ Connecting to a network
En
31
Wireless network
Connecting the unit to a wireless network
Connect the unit to a wireless router (access point).
Select the connection method appropriate for your network environment from “Wireless
(Wi-Fi)” in the setup menu.
Internet
Wireless(Wi-Fi)
Wireless router
(access point)
S
·
·
·
·
·
e
W
S
A
M
P
l
P
h
c
a
I
e
S
a
c
n
N
ct
B
re
es
ua
C
a
ut
W
s
l
od
t
i
P
S
e
s
o
o
e
e
n
F
i
t
tup
method.
i Settings
nt Scan
ting
(iOS)
Modem
[ENTER]:OK
[RETURN]:Cancel
Connection method
Operation
WPS Button
Use the WPS button on your wireless router
(access point) to establish a wireless
connection.
Share Wi-Fi Settings (iOS)
Apply network settings from an iOS device
(such as an iPhone).
Access Point Scan
Select an access point from a list displayed
after a search of available access points.
Manual Setting
Establish a wireless network connection by
entering required information, such as the SSID,
manually.
PIN Code
Establish a wireless connection by registering
the unit’s PIN with your wireless router (access
point). This method can be used if the wireless
router (access point) supports the WPS PIN
feature.
The unit
Mobile device
For details on connection, see “Connecting the unit to a wireless network”.
The
indicator on the front panel glows when the unit is connected to a wireless
network.
Glows (green)
• You cannot use the wireless network connection simultaneously with the wired network connection (p. 31)
or Wireless Direct (p. 40).
• If the unit and the wireless router (access point) are too far apart, the unit may not connect to a wireless
router (access point). In such case, place them close to each other.
• If the unit will not be connected to a wireless router (access point), Wireless Direct (p. 40) can be used to
play music files stored on your mobile device via the unit.
Choosing a connection method
If you want to:
Use this connection method
Use an iOS device to easily connect to a
network
Share Wi-Fi Settings (iOS) (p. 33)
Connect to a wireless router (access point)
that supports the WPS (push button) feature
WPS Button (p. 34)
Connect to a wireless router (access point)
that supports the WPS PIN feature
PIN Code (p. 39)
Connect to a network by search for a nearby
access point
Access Point Scan (p. 35)
Connect directly to an access point that
cannot be located
Manual Setting (p. 37)
NETWORKS ➤ Connecting to a network
En
32
Sharing the iOS device setting
7
You can easily setup a wireless connection by applying the
connection settings on iOS devices (such as an iPhone).
Use the S/T keys to select “Share Wi-Fi Settings
(iOS)”, and then press the ENTER key.
Wireless(Wi-Fi)
Before proceeding, confirm that your iOS device is connected to a
wireless router (access point).
S
·
·
·
·
·
• You need iOS device with iOS 7.1 or later.
e
W
S
A
M
P
l
P
h
c
a
I
e
S
a
c
n
N
ct
B
re
es
ua
C
• The connection settings on iOS devices cannot be applied to the unit to establish
a wireless connection if your wireless router (access point) uses WEP encryption.
See “Searching for a wireless router (access point)” (p. 35) to establish a
connection.
1
2
/
ENTER
RETURN
3
Press the z key to turn on this unit.
8
I
f
i
·
·
·
f
o
n
N
N
A
i
·B
The setup menu is displayed on the TV screen.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
s
o
o
e
e
n
F
i
t
tup
method.
i Settings
nt Scan
ting
(iOS)
When the following screen is displayed, press the
ENTER key.
Press the SETUP key twice.
Use the S/T keys to select “Network”, and then
press the ENTER key.
t
i
P
S
e
[ENTER]:OK
[RETURN]:Cancel
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 18).
4
a
ut
W
s
l
od
l
i
e
E
l
n
l
S
S
l
t
t
T
l
f
u
h
h
o
i
w
a
a
w
a
o
p
m
or
et
r
r
i
l
r
r
u
m
o
e
i
n
i
k
e
s
a
o
[
[R
Wing i
g se
zed.
set
sets
ic s
tion
th s
ENTE
ETUR
Fi Settings
s begun, the
ttings will be
tings
ervice
account
ettings
R]:Start
N]:Cancel
SETUP
• The settings to be deleted (initialized) will be displayed. If you do not want to
delete these settings, press the RETURN key to terminate the connection.
9
When the following screen is displayed, press the
ENTER key.
Share
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
M
c
n
W
y
a
o
e
i
o
k
n
t
u
Wi-Fi
e sure your i
nected to you
work, and the
Fi settings s
r iOS device.
Settings
OS device is
r Wi-Fi
n open the
creen of
[ENTER]:Confirm
[RETURN]:Cancel
NETWORKS ➤ Connecting to a network
En
33
10 Display the Wi-Fi setup screen on the iOS device
and select the unit from “SETUP A NEW AIRPLAY
SPEAKER...”.
7
Use the S/T keys to select “WPS Button”, and then
press the ENTER key.
Wireless(Wi-Fi)
Follow the on-screen instructions displayed on the iOS
device.
S
·
·
·
·
·
Using the WPS push button configuration
You can easily set up a wireless connection with one push of the
WPS button.
1
2
3
/
ENTER
SETUP
Press the z key to turn on this unit.
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 18).
Press the SETUP key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
e
W
S
A
M
P
l
P
h
c
a
I
e
S
a
c
n
N
ct
B
re
es
ua
C
a
ut
W
s
l
od
t
i
P
S
e
s
o
o
e
e
n
F
i
t
tup
method.
i Settings
nt Scan
ting
(iOS)
[ENTER]:OK
[RETURN]:Cancel
8
Push the WPS button on the wireless router (access
point).
9
Press the ENTER key.
When a connection has been established (the device has
been paired with the unit), “Completed” will be displayed on
the TV screen.
If “Not connected” is displayed, press the ENTER key to
repeat the process beginning with step 6, or see the
information below to try another connection method.
• The WPS button cannot be used to establish a wireless connection if your
wireless router (access point) uses WEP encryption, or if the router’s MAC
address filter is enabled. See “Searching for a wireless router (access point)”
(p. 35) to establish a connection.
• The WPS button cannot be used to establish a wireless connection if your
wireless router (access point) is configured so that it does not broadcast its SSID.
See “Setting up the wireless connection manually” (p. 37) to establish a
connection.
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the
Wi-Fi Alliance, which allows easy establishment of a wireless
home network.
NETWORKS ➤ Connecting to a network
En
34
Searching for a wireless router (access
point)
Find and connect to a nearby wireless router (access point).
1
2
Press the z key to turn on this unit.
3
Press the SETUP key twice.
The wireless connection setting screen appears on the TV.
Access
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 18).
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
Network Connection
SETUP
Wired
Wireless(Wi-Fi)
Wireless Direct
7
Use the S/T keys to select the desired access point
and press the ENTER key.
▲
SSID
The setup menu is displayed on the TV screen.
/
/
ENTER
8
Use the S/T keys to select “Access Point Scan”,
and then press the ENTER key.
:
Security:
Security K
:
Connect
▼
[ENT
[RETU
Point
Access
Scan
Point
1
WPA2-PSK(AES)
ey
ER]:Confirm
RN]:Cancel
9 Press the ENTER key.
10 Use the W/X/S/T and ENTER keys to enter the
security key.
*
(
.
0
A
N
a
n
S
O
C
****_
) [
, :
1 2
B C
O P
b c
o p
pace
K
ANCEL
]
;
3
D
Q
d
q
{
_
4
E
R
e
r
BK
}
|
5
F
S
f
s
SP
<
/
6
G
T
g
t
>
\
7
H
U
h
u
DE
*
$
8
I
V
i
v
LE
!
~
9
J
W
j
w
TE
?
^
@
K
X
k
x
#
'
+
L
Y
l
y
CL
%
"
M
Z
m
z
EA
&
`
=
←
→
R
[]/[]: Move the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
Wireless(Wi-Fi)
S
·
·
·
·
·
e
W
S
A
M
P
l
P
h
c
a
I
e
S
a
c
n
N
ct
B
re
es
ua
C
a
ut
W
s
l
od
t
i
P
S
e
s
o
o
e
e
n
F
i
t
tup
method.
i Settings
nt Scan
ting
(iOS)
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen will return to that
displayed in step 8.
[ENTER]:OK
[RETURN]:Cancel
The list of available access points appears on the TV
screen.
NETWORKS ➤ Connecting to a network
En
35
11 Use the S/T keys to select “Connect” and press the
ENTER key to start the connection process.
When a connection has been established (the device has
been paired with the unit), “Completed” will be displayed on
the TV screen.
If “Not connected” is displayed press the ENTER key to
repeat the process beginning with step 6, or see the
information below to try another connection method.
• “Access Point Scan” cannot be used to establish a wireless connection if
your wireless router (access point) is configured so that it does not
broadcast its SSID. See “Setting up the wireless connection manually”
(p. 37) to establish a connection.
12 Press the SETUP key to exit the setup menu.
/
ENTER
SETUP
NETWORKS ➤ Connecting to a network
En
36
Setting up the wireless connection
manually
Use the S/T keys to select “SSID”.
Manual
Setup the SSID (network name), encryption method and security
key for your network manually.
▲
SSID
1
2
Press the z key to turn on this unit.
Security:
Security K
:
Connect
▼
[ENT
[RETU
3
Press the SETUP key twice.
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 18).
The setup menu is displayed on the TV screen.
/
/
ENTER
8
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
SETUP
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
7
Use the S/T keys to select “Manual Setting”, and
then press the ENTER key.
e
W
S
A
M
P
l
P
h
c
a
I
e
S
a
c
n
N
ct
B
re
es
ua
C
a
ut
W
s
l
od
t
i
P
S
e
s
o
o
e
e
n
F
i
t
tup
method.
i Settings
nt Scan
ting
[ENTER]:OK
[RETURN]:Cancel
:
None
ey
ER]:Confirm
RN]:Cancel
Use the W/X/S/T keys and the ENTER key to enter
the SSID of the access point.
a
(
.
0
A
N
a
n
S
O
C
bc_
) [
, :
1 2
B C
O P
b c
o p
pace
K
ANCEL
]
;
3
D
Q
d
q
{
_
4
E
R
e
r
BK
}
|
5
F
S
f
s
SP
<
/
6
G
T
g
t
>
\
7
H
U
h
u
DE
*
$
8
I
V
i
v
LE
!
~
9
J
W
j
w
TE
?
^
@
K
X
k
x
#
'
+
L
Y
l
y
CL
%
"
M
Z
m
z
EA
&
`
=
←
→
R
[]/[]: Move the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen will return to that
displayed in step 8.
10 Use the S/T keys to select “Security” and the W/X
keys to select the encryption method.
Wireless(Wi-Fi)
S
·
·
·
·
·
9
Setting
(iOS)
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
• As communications are not encrypted when “None” is selected, selecting
this option poses the risk that third parties may access the unit without your
permission.
NETWORKS ➤ Connecting to a network
En
37
11 Use the S/T keys to select “Security Key” and
press the ENTER key.
13 Use the S/T keys to select “Connect” and press the
ENTER key to start the connection process.
When a connection has been established (the device has
been paired with the unit), “Completed” will be displayed on
the TV screen.
• If you select “None” in step 10, this item is not available.
12 Use the W/X/S/T and ENTER keys to enter the
security key.
If you select “WEP” in step 10, enter either 5 or 13
character string, or 10 or 26 hexadecimal (base 16) keys.
If “Not connected” is displayed press the ENTER key to
repeat the process beginning with step 6.
14 Press the SETUP key to exit the setup menu.
If you select the method other than “WEP”, enter either 8 to
63 character string, or 64 hexadecimal (base 16) keys.
• Hexadecimal (base 16) keys use combinations of the numbers 0 through 9
and the letters a through f. Letters are not case sensitive.
/
/
ENTER
SETUP
*
(
.
0
A
N
a
n
S
O
C
****_
) [
, :
1 2
B C
O P
b c
o p
pace
K
ANCEL
]
;
3
D
Q
d
q
{
_
4
E
R
e
r
BK
}
|
5
F
S
f
s
SP
<
/
6
G
T
g
t
>
\
7
H
U
h
u
DE
*
$
8
I
V
i
v
LE
!
~
9
J
W
j
w
TE
?
^
@
K
X
k
x
#
'
+
L
Y
l
y
CL
%
"
M
Z
m
z
EA
&
`
=
←
→
R
[]/[]: Move the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CLEAR]: Cancel character entry, and return to the previous screen.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen will return to that
displayed in step 8.
NETWORKS ➤ Connecting to a network
En
38
8
Using the WPS PIN code
Register the unit’s PIN code with your wireless router (access point)
to establish a connection.
1
2
Press the z key to turn on this unit.
3
Press the SETUP key twice.
Use the S/T keys to select the desired access point
and press the ENTER key.
The PIN code of the unit appears on the TV screen.
PIN
PIN
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 18).
E
i
P
t
/
ENTER
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
Network Connection
SETUP
Wired
Wireless(Wi-Fi)
Wireless Direct
7
Wireless(Wi-Fi)
e
W
S
A
M
P
l
P
h
c
a
I
e
S
a
c
n
N
ct
B
re
es
ua
C
a
ut
W
s
l
od
t
i
P
S
e
s
o
o
e
e
n
F
i
t
tup
method.
i Settings
nt Scan
ting
t
h
E
n
he PI
e acc
NTER
necti
N cod
ess p
to st
on pr
e
oint.
art
ocess.
9
Enter the unit’s PIN code into the wireless router
(access point).
For details on settings, refer to the instruction manual of the
wireless router (access point).
10 Press the ENTER key to start the connection
process.
When a connection has been established (the device has
been paired with the unit), “Completed” will be displayed on
the TV screen.
If “Not connected” is displayed press the ENTER key to
repeat the process beginning with step 6, or see the
information below to try another connection method.
Use the S/T keys to select “PIN Code”, and then
press the ENTER key.
S
·
·
·
·
·
ter
to t
ess
e co
[ENTER]:Start
[RETURN]:Cancel
The setup menu is displayed on the TV screen.
4
n
n
r
h
Code
Code:00000000
(iOS)
• The PIN code cannot be used to establish a wireless connection if your
wireless router (access point) uses WEP encryption, or if the router’s MAC
address filter is enabled. See “Searching for a wireless router (access
point)” (p. 35) to establish a connection.
11 Press the SETUP key to exit the setup menu.
[ENTER]:OK
[RETURN]:Cancel
The list of available access points appears on the TV
screen.
NETWORKS ➤ Connecting to a network
En
39
Connecting a mobile device to the unit directly (Wireless Direct)
Connect a mobile device directly to the unit without using a wireless
router (access point).
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless Direct”, and
then press the ENTER key.
Wireless Direct supports the following.
– Operation of the unit using a mobile device to which the
dedicated HOME THEATER CONTROLLER (WLAN) app has
been installed.
– Use of AirPlay to play music files stored on an iOS device.
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
Mobile device
/
/
ENTER
SETUP
The unit
7
• You cannot use Wireless Direct simultaneously with the wired network connection
(p. 31) or the wireless network connection (p. 32).
Settings
None, WPA2-PSK (AES)
• When Wireless Direct is enabled, the unit cannot connect to the Internet.
Therefore, you cannot use any kind of Internet service such as Internet radio.
1
2
3
Use the S/T keys to select “Security” and the W/X
keys to select the encryption method.
In most cases, “WPA2-PSK (AES)” should be selected. If
your mobile device does not support “WPA2-PSK (AES)”,
select “None”.
Press the z key to turn on this unit.
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 18).
• As communications are not encrypted when “None” is selected, selecting
this option poses the risk that third parties may access the unit without your
permission.
Press the SETUP key twice.
The setup menu is displayed on the TV screen.
8
Use the S/T keys to select “Security Key” and
press the ENTER key.
• If you select “None” in step 7, this item is not available.
NETWORKS ➤ Connecting to a network
En
40
9
Use the W/X/S/T and ENTER keys to enter the
security key.
Enter either 8 to 63 character string, or 64 hexadecimal
(base 16) keys.
• Hexadecimal (base 16) keys use combinations of the numbers 0 through 9
and the letters a through f. Letters are not case sensitive.
*
(
.
0
A
N
a
n
S
O
C
/
/
ENTER
SETUP
****_
) [
, :
1 2
B C
O P
b c
o p
pace
K
ANCEL
]
;
3
D
Q
d
q
{
_
4
E
R
e
r
BK
}
|
5
F
S
f
s
SP
<
/
6
G
T
g
t
>
\
7
H
U
h
u
DE
*
$
8
I
V
i
v
LE
!
~
9
J
W
j
w
TE
?
^
@
K
X
k
x
#
'
+
L
Y
l
y
CL
%
"
M
Z
m
z
EA
&
`
=
←
→
R
10 Use the S/T keys to select “Save” and press the
ENTER key to save the setting.
This completes the settings and “Set the mobile device.”
will be displayed on the TV screen. The unit functions as an
access point.
Next, configure the Wi-Fi settings of a mobile device.
11 Configure the Wi-Fi settings of a mobile device.
For details on settings of your mobile device, refer to the
instruction manual of the mobile device.
a Enable the Wi-Fi function on the mobile device.
b Select the SSID displayed in step 9 from the list of available
access points.
c When you are prompted for a password, enter the security key
displayed in step 9.
[]/[]: Moves the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
12 Press the SETUP key to exit the setup menu.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen below will be displayed.
Wireless
▲
SSID
:
Security:
Security K
:
Save
▼
[ENT
[RETU
Direct
YSP-1600
XXXXXX
WPA2-PSK(AES)
ey
*************
ER]:Confirm
RN]:Cancel
• Before proceeding to the next step, record the following information. These
information will be needed to configure the Wi-Fi setting of a mobile device.
– SSID displayed on the TV screen
– Security key you have just entered
NETWORKS ➤ Connecting to a network
En
41
Playing back music stored on media servers (PCs/NAS)
You can play back music files stored on your PC or DLNA-compatible NAS on the unit.
Media sharing setup
To play back music files stored on your PC or DLNA-compatible NAS, first you need to
• To use this function, the unit and your PC must be connected to the same router (p. 31). You can check
whether the network parameters (such as the IP address) are properly assigned to the unit in “Information”
(p. 54) in the setup menu.
configure the media sharing setting on each music server.
• The audio may be interrupted while using the wireless network connection. In this case, use the wired
network connection.
• The following file formats are supported.
– The unit supports playback of WAV (PCM format only), MP3, WMA, MPEG-4 AAC, FLAC and ALAC
(Apple Lossless Audio Codec) files (1- or 2-channel audio only).
– The unit is compatible with sampling rates of up to 192 kHz for WAV and FLAC files, 96 kHz for ALAC
files, and 48 kHz for other files.
– The unit supports gapless playback of WAV, FLAC and ALAC files.
– To play back FLAC files, you need to install server software that supports sharing of FLAC files via DLNA
on your PC or use a NAS that supports FLAC files.
– Digital Rights Management (DRM) contents cannot be played back.
For a PC with Windows Media Player installed
This unit supports Windows Media Player 11 or later. This section explains Windows
Media Player 12 setup as an example.
1
2
3
4
Start Windows Media Player 12 on your PC.
5
Click “OK” to exit.
Select “Stream”, then “Turn on media streaming”.
Click “Turn on media streaming”.
Select “Allowed” from the drop-down list next to the unit’s model
name.
For a PC or a NAS with other DLNA server software
installed
Refer to the instruction manual for the device or software and configure the media
sharing settings.
Playing music files
Use the MusicCast CONTROLLER app installed on your mobile device to play music
files.
• Configure basic settings for the MusicCast CONTROLLER app before playing music files.
• Refer to the supplied "MusicCast Setup Guide" for details.
NETWORKS
➤ Playing back music stored on media servers (PCs/NAS)
En
42
Listening to Internet radio
You can listen to Internet radio stations from all over the world.
• To use this function, the unit must be connected to the Internet (p. 31). You can check whether the network parameters (such as the IP address) are properly assigned to the
unit in “Information” (p. 54) in the setup menu.
• You may not be able to receive some Internet radio stations.
• The unit uses the vTuner Internet radio station database service.
• This service may be discontinued without notice.
NET RADIO
1-3
Playback of Internet radio
Registering favorite Internet radio stations
Use the MusicCast CONTROLLER app installed on your mobile
device to select an Internet radio station.
Assign Internet radio stations to the NET RADIO keys on the remote
control, or save them in the vTuner Bookmarks folder.
Assigning a station to a NET RADIO key
• Configure basic settings for the MusicCast CONTROLLER app before selecting
an Internet radio station.
• Refer to the supplied "MusicCast Setup Guide" for details.
1
2
Select the desired Internet radio station.
Press and hold one of the NET RADIO keys (1–3) for
at least 3 seconds.
❑ Tuning into assigned Internet radio stations
1
Press the NET RADIO key (1–3) to which the desired
Internet radio station has been assigned.
The input source switches to NET, and streaming begins.
STATUS
TV
HDMI
ANALOG
BLUETOOTH
NET
SURROUND
Glows
NETWORKS ➤
Listening to Internet radio
En
43
Registering the station on the vTuner website
You can also register your favorite Internet radio stations on the vTuner website.
1
Select any of Internet radio stations on the unit.
This operation is necessary to register the radio station for the first time.
2
Check the vTuner ID of the unit.
You can find the vTuner ID in “Information” (p. 54) in the setup menu.
3
Access the vTuner website (http://yradio.vtuner.com/) with the web
browser on your PC and enter the vTuner ID.
You can switch the language.
Enter the vTuner ID in this area.
• To use this feature, you need to create your personal account. Create your account using your e-mail
address.
4
Register your favorite radio stations.
Click the “Add” icon (
) next to the station name.
• To remove the station from the “Bookmarks” folder, select “Bookmarks” in the Home screen, and then
click the “Remove” icon (
) next to the station name.
NETWORKS ➤
Listening to Internet radio
En
44
Playing back music with AirPlay
The AirPlay function allows you to play back iTunes or iPod music on the unit via
network.
Playback of iTunes/iPod music contents
Follow the procedure below to play back iTunes/iPod music contents on the unit.
• This section describes “iPod touch”, “iPhone” and “iPad” as the “iPod”. “iPod” refers to “iPod touch”,
“iPhone” and “iPad”, unless otherwise specified.
1
Turn on the unit, and start iTunes on the PC or display the playback
screen on the iPod.
If the iTunes/iPod recognizes the unit, the AirPlay icon (
) appears.
iTunes
iTunes (example)
iPod iOS7/iOS8 (example)
iPod iOS6 (example)
(wired or
wireless)
(wired or
wireless)
Router
The unit
• If the icon does not appear, check whether the unit and PC/iPod are connected to the router properly.
2
On the iTunes/iPod, click (tap) the AirPlay icon and select the unit
(network name of the unit) as the audio output device.
iPod
iTunes (example)
• To use this function, the unit and your PC or iPod must be connected to the same router (p. 31). You can
check whether the network parameters (such as the IP address) are properly assigned to the unit in
“Information” (p. 54) in the setup menu.
• When using a multiple SSID router, access to the unit might be restricted depending on the SSID to
connect. Connect the unit and iPod to the same SSID.
iPod (example)
YSP-1600 XXXX
YSP-1600 XXXX
Network name of the unit
• The AirPlay function can be used with an iPhone, iPad, or iPod touch running iOS 4.3.3 or later, a Mac
running OS X version 10.8 “Mountain Lion” or later, or a Mac or Windows computer with iTunes 10.2.2 or
later installed.
NETWORKS ➤
Playing back music with AirPlay
En
45
3
Select a song and start playback.
To operate playback, use the Music app on the iPod or iTunes on the PC.
The input source switches to NET, and playback begins.
NET
Glows
• You can turn on the unit automatically when starting playback on iTunes or iPod by setting “Network
Standby” (p. 56) in the setup menu to “On”.
• You can edit the network name (the unit’s name on the network) displayed on iTunes/iPod in “Network
Name” (p. 56) in the setup menu.
• You can adjust the unit’s volume from the iTunes/iPod during playback.
Caution
• When you use iTunes/iPod controls to adjust volume, the volume may be unexpectedly loud. This could
result in damage to the unit or speakers. If the volume suddenly increases during playback, stop
playback on the iTunes/iPod immediately.
NETWORKS ➤
Playing back music with AirPlay
En
46
Playing back music stored on mobile devices
Use this function to play music stored on your mobile device over a network.
Using a mobile device to play songs
Use the MusicCast CONTROLLER app installed on your mobile device to operate
playback.
Router
(wired or
wireless)
• Configure basic settings for the MusicCast CONTROLLER app before playing music.
The unit
• Refer to the supplied "MusicCast Setup Guide" for details.
Caution
• When you use mobile device controls to adjust volume, the volume may be unexpectedly loud. This
could result in damage to the unit or speakers. If the volume suddenly increases during playback, stop
playback on the mobile device immediately.
Mobile device
• To use this function, the unit and your PC or mobile device must be connected to the same router (p. 31).
You can check whether the network parameters (such as the IP address) are properly assigned to the unit
in “Information” (p. 54) in the setup menu.
• When using a multiple SSID router, access to the unit might be restricted depending on the SSID to
connect. Connect the unit and mobile device to the same SSID.
NETWORKS
➤ Playing back music stored on mobile devices
En
47
SETTINGS
Setup menu
A variety of settings for this unit can be specified and adjusted from the setup menu. Among the options available are channel volume control,
HDMI settings, and network settings.
The setup menu is displayed on, and operated from, the TV screen. See “Displaying the menu screen on the TV” (p. 18) for instructions on
displaying the setup menu on the TV.
Setting the setup menu
1
/
/
ENTER
2
Press the SETUP key.
To display the Network or Bluetooth menu, press the
SETUP key again.
Repeat these steps to display the desired menu.
Setup menu
Setup Menu
Setup Menu
RETURN
SETUP
Use the S/T key to select a menu and then press
the ENTER key.
Channel Level
Sound
Dynamic Range
HDMI
Audio Delay
Function
Information
Channel Level
Sound
Dynamic Range
HDMI
Audio Delay
Function
Information
The X key can be used in place of the ENTER key.
• Hold down the SETUP key for more than 3 seconds to display “OSD
Language” directly on the screen (p. 19, 52).
• If an update for the unit’s firmware is available, an envelope icon (
displayed in the setup menu (p. 59).
) will be
Press the W key or RETURN key to return to the previous
menu.
3
Use the S/T key to change the setting value of each
menu.
4
Press the SETUP key again to exit the setup menu.
SETTINGS ➤ Setup menu
En
48
Setup menu list
Menu
Item
HDMI
Function
Page
Adjust the volume of each channel.
50
Dynamic Range
Specify dynamic range.
50
Audio Delay
Adjust the delay between video and audio output.
50
HDMI Control
Turn HDMI control on or off.
51
HDMI Audio Out
Choose whether HDMI audio input is played via this unit or the TV.
51
Audio Assign
Specify the audio input from the TV jack or HDMI IN jack when HDMI is selected as
the input source.
51
Dimmer
Adjust the brightness of indicators on the front panel.
52
OSD Language
Change the language used for menus displayed on the TV screen.
52
Auto Power Standby
Turn Auto Power Standby on or off.
52
TV Remote Repeater
Enable/disable the TV Remote Repeater function.
58
Audio
Display audio input signal information.
53
Video
Display video input signal information.
53
System
Display this unit’s firmware version.
53
Information
Display the unit’s network information.
54
Network Connection
Select the network connection method.
54
Channel Level
Sound
Front L, Front R, Center, Surround L, Surround R,
Subwoofer
Function
Information
Network
IP Address
DHCP, IP Address, Subnet Mask, Default
Gateway, DNS Server (P), DNS Server (S)
Configure the network parameters (such as IP address).
55
MAC Address Filter
Filter, MAC Address 1–10
Set the MAC address filter to limit access to the unit from other network devices.
55
Network Standby
Enable/disable the function that turns on the unit from other network devices.
56
Network Name
Edit the network name (the unit’s name on the network) displayed on other network
devices.
56
Update the firmware via the network.
56
Bluetooth
Enable/disable the Bluetooth functions.
57
Transmission
Turn the function that transmits audio to a Bluetooth device, such as Bluetooth
speakers, on or off.
57
Device Search
Search for the Bluetooth device, such as Bluetooth speakers, to which audio will be
transmitted.
57
MAC Address
Display the MAC address for the Bluetooth connection.
57
Network Update
Perform Update
Bluetooth
SETTINGS ➤ Setup menu
En
49
Sound
Channel Level
Setup Menu
Audio Delay
➜
Sound
➜
Channel Level
Setup Menu
➜
Sound
➜
Audio Delay
Adjust the volume of each channel to balance output levels. Use test sounds output
from each channel to adjust volume for optimal balance.
TV images sometimes lag behind the sound. You can use this function to delay the
sound output to synchronize it with the video image.
Item
Front L, Front R, Center, Surround L, Surround R, Subwoofer
Settings
Adjustable range
-10 to +10
0 ms–500 ms
Specify audio output timing in increments of 5 ms.
Auto (default)
Adjust the delay between video and audio output automatically when a TV that
supports an automatic lipsync function is connected to the unit via HDMI.
Dynamic Range
Setup Menu
➜
Sound
➜
Dynamic Range
Adjust this unit’s dynamic range (difference between maximum and minimum volumes).
Settings
Auto (default)
Set dynamic range at a level that supports comfortable listening at low volumes.
Standard
The dynamic range recommended for regular home use.
Max
Output sound without adjusting the dynamic range of the input signals.
SETTINGS ➤ Setup menu
En
50
HDMI
Use to configure the settings related to HDMI signals and the HDMI control function.
HDMI Control
Setup Menu
Audio Assign
➜
HDMI
➜
HDMI Control
Turn HDMI control (p. 20) on or off.
Setup Menu
➜
HDMI
➜
Audio Assign
Specify whether audio is input via the HDMI IN jack or the TV (digital optical) jack of the
unit when HDMI is selected as the input source.
Settings
Off (default)
Disable the HDMI control function. The standby power consumption of this unit
decreases.
On
Enable the HDMI control function.
Settings
HDMI (default), Optical
HDMI Audio Out
This setting can be configured only when “HDMI Control” is set to “Off”.
Setup Menu
➜
HDMI
➜
HDMI Audio Out
Use to select a device to play back HDMI audio signals.
Settings
AMP (default)
Play back the input sound signal.
TV
Plays audio content from the TV connected to the HDMI OUT (ARC) jack.
Volume cannot be adjusted from the unit. Use the TV to adjust volume.
• When “HDMI Control” is set to “On”, select the audio output device based on the settings configured for the
TV connected to this unit.
• HDMI video signals input to the HDMI IN jack of this unit are always output from the HDMI OUT (ARC) jack
of this unit.
SETTINGS ➤ Setup menu
En
51
Function
Dimmer
Auto Power Standby
➜
Setup Menu
Function
➜
Dimmer
Setup Menu
➜
Function
➜
Auto Power Standby
Adjust the brightness of indicators on the front panel.
Turn Auto Power Standby on or off.
Settings
-2 (off), -1 (normal; default), 0 (bright)
When this function is activated, the unit turns off when it is not in use.
• If this function is set to “-2” or “-1”, the display brightens only when operations are performed with this unit.
OSD Language
Setup Menu
Settings
Off (default setting other than U.K., Europe and Russia models), On (default setting for U.K., Europe
and Russia models)
When “Auto Power Standby” is set to “On”, the unit automatically turns off as indicated
below
➜
Function
➜
OSD Language
Use to select the language used for menus displayed on the TV screen.
Settings
Menus are displayed in Japanese.
ENGLISH
(default)
Menus are displayed in English.
DEUTSCH
Menus are displayed in German.
FRANÇAIS
Menus are displayed in French.
ESPAÑOL
Menus are displayed in Spanish.
ITALIANO
Menus are displayed in Italian.
NEDERLANDS
Menus are displayed in Dutch.
РУССКИЙ
Menus are displayed in Russian.
SVENSKA
Menus are displayed in Swedish.
TÜRK
Menus are displayed in Turkish.
• Audio is input to the unit, but no operations have been performed with the unit for
more than 8 hours.
• HDMI, BLUETOOTH or NET is selected as the input source, but no audio has been
input to the unit or no operations have been performed with the unit for more than 20
minutes.
• HDMI is selected as the input source, but no playback device has been connected to
the unit’s HDMI IN jack for more than 20 minutes.
5 minutes before the auto power standby function automatically turns the unit off, the
indicators on the front panel indicate a countdown until the unit is turned off.
5 minutes before
One indicator turns off for every minute that passes.
10 seconds before
The blinking indicator moves to the left for every second that passes.
... 9 seconds before 10 seconds before
• Hold down the SETUP key for more than 3 seconds to display “OSD Language” directly on the TV screen.
• The settings may be changed automatically when using the TV which supports the HDMI control function.
• Auto Power Standby can also be turned on or off using the keys on the front panel (p. 62).
SETTINGS ➤ Setup menu
En
52
Information
TV Remote Repeater
Setup Menu
➜
Function
➜
Display information for the audio and video signal input to this unit.
TV Remote Repeater
Audio
Turn the TV Remote Repeater function on or off.
Setup Menu
Settings
Off (default)
Disable the TV Remote Repeater function.
On
Enable the TV Remote Repeater function.
➜
Information
➜
Audio
The following information on the current audio input signal is displayed.
Format
Digital audio format
Number of channels
The number of channels contained within the input signal—front/
surround/low frequency effects (LFE). Example: “3/2/0.1” means signal
contains 3 front channels, 2 surround channels, and LFE.
If the signal contains channels other than front, surround, and LFE, the
total number of channels may be displayed. Example: “5.1ch”.
Sampling frequency
The sampling frequency of the digital input signal
Bit rate
The per-second bit rate of the input signal
For details, see “Operating a TV via the TV Remote Repeater function of the unit”
(p. 58).
• The audio bit rate or sampling frequency may not be displayed for some input signals.
Video
Setup Menu
➜
Information
➜
Video
The following information on the current video input signal is displayed.
Type
HDMI or DVI
Resolution
Video signal resolution
System
Setup Menu
➜
Information
➜
System
Display the version of firmware currently installed on this unit.
SETTINGS ➤ Setup menu
En
53
Network
Configures the network settings.
• Some menus are not superimposed over video content on the TV screen.
Information
Setup Menu
Network Connection
➜
Network
➜
Information
Display the network information on the unit.
Setup Menu
➜
Network
➜
Network Connection
Select the network connection method.
Settings
• The options displayed vary according to the type of network connection (Wired/Wireless (Wi-Fi)/Wireless
Direct).
Status
The connection status of the NETWORK jack
Connection
Connection method
MC Network
The connection status of MusicCast Network
SSID
The access point to which the unit is connected
Security
The encryption method for your network
MAC Address
MAC address (Ethernet/Wi-Fi)
IP Address
IP address
Subnet Mask
Subnet mask
Default Gateway
The IP address of the default gateway
DNS Server (P)
The IP address of the primary DNS server
DNS Server (S)
The IP address of the secondary DNS server
vTuner ID
The ID of the Internet radio (vTuner)
Wired
Select this option when connecting the unit to a network with a network
cable (not supplied).
Wireless (Wi-Fi)
Select this option when connecting the unit to a network via the wireless
router (access point).
Wireless Direct
Select this option when connecting a mobile device to the unit directly.
SETTINGS ➤ Setup menu
En
54
IP Address
MAC Address Filter
➜
Setup Menu
Network
➜
IP Address
Configure the network parameters (such as IP address).
❑ DHCP
➜
Setup Menu
Network
➜
MAC Address Filter
The MAC address filter limits network devices that can be used to operate the unit.
When operating the unit via an app on a mobile device, specify the MAC address of the
device.
Select whether to use a DHCP server.
Settings
• Operation of the AirPlay function (p. 45) or DLNA-compatible device (p. 42) is not limited by this setting.
Off
The DHCP server is not used. Configure the network parameters
manually. For details, see “Manual network settings”.
❑ Filter
The DHCP server is used to automatically obtain the unit’s network
parameters (such as IP address).
Enable/disable the MAC address filter.
On (default)
Manual network settings
1
2
Set “DHCP” to “Off”.
Settings
Off (default)
Disable the MAC address filter.
On
Enable the MAC address filter. In “MAC Address 1–10”, specify the MAC
addresses of the network devices that will operate the unit.
Use the S/T keys to select a parameter type.
❑ MAC Address 1–10
IP Address
Specify an IP address.
Subnet Mask
Specify a subnet mask.
Specify the MAC addresses (up to 10) of the network devices that will operate the unit
when “Filter” is set to “On”.
Default Gateway
Specify the IP address of the default gateway.
DNS Server (P)
Specify the IP address of the primary DNS server.
DNS Server (S)
Specify the IP address of the secondary DNS server.
3
Use the W/X keys to move the edit position and the S/T keys to
select a value.
4
Press the ENTER key.
1
2
Use the S/T keys to select an MAC address number (1 to 10).
3
Press the ENTER key.
Use the W/X keys to move the edit position and the S/T keys to
select a value.
SETTINGS ➤ Setup menu
En
55
Network Standby
Setup Menu
➜
Network Name
Network
➜
Network Standby
Setup Menu
➜
➜
Network
Network Name
Turn the function that controls the unit’s power (Network Standby) when a network
device or Bluetooth device is operated on or off.
Edit the name displayed for this device (the unit’s name on the network) on other
network devices. A name up to 15 characters in length may be specified.
Settings
1
Off
Disable the network standby function.
Use the W/X keys to move the edit position and the S/T keys to
select a character.
The unit will turn on when the MusicCast CONTROLLER or
HOME THEATER CONTROLLER (WLAN) app installed on
your mobile device is used to initiate playback while the
unit is off.
On (default)
Enable the network
standby function.
The unit will turn on and off in accordance with the
following Bluetooth device operations.
Coordinated power on
When a Bluetooth device is connected to this unit while it is
off, this unit turns on and the input source switches to
BLUETOOTH.
Coordinated power off
When a Bluetooth device is disconnected from this unit
while it is on, this unit turns off.
(Only when BLUETOOTH is selected as the input source.)
• The unit consumes more power when “Network Standby” is set to “On” than when it is set to “Off”.
Network Name
YSP-1600 1B08FA
[RETURN]:Back
• The following alphanumeric characters and symbols may be used.
( ) [ ] { } < > * ! ? # % & . , : ; _ | / \ $ ~ ^ ' " ` 0–9 @ + - = A–Z a–z
2
Press the RETURN key.
Network Update
Setup Menu
➜
Network
➜
Network Update
Update the firmware via the network.
Perform Update
This option is available after firmware has been updated. For details, see “Updating the
unit’s firmware” (p. 59).
SETTINGS ➤ Setup menu
En
56
Bluetooth
Configures the Bluetooth settings.
• Some menus are not superimposed over video content on the TV screen.
Bluetooth
Device Search
➜
Setup Menu
Bluetooth
➜
Bluetooth
Enables/disables the Bluetooth function.
Disable the Bluetooth function.
On (default)
Enable the Bluetooth function.
Setup Menu
➜
Bluetooth
➜
Bluetooth
Device Search
MAC Address
Transmission
Setup Menu
➜
Select the Bluetooth speakers or headphones to which audio will be transmitted, and
the pair the speakers or headphones with the unit to establish a connection.
Settings
Off
Setup Menu
➜
➜
➜
Bluetooth
MAC Address
Display the MAC address for the Bluetooth connection.
Transmission
Transmit audio from the unit to Bluetooth speakers or headphones.
Settings
Off (default)
Audio can not be transmitted.
On
Audio input to the unit can be transmitted to Bluetooth speakers or
headphones.
SETTINGS ➤ Setup menu
En
57
Operating a TV via the TV Remote Repeater function of the unit
When the TV Remote Repeater function is enabled, the unit receives TV remote control signals at the remote control sensor (on front) and
transmits the signals from the TV Remote Repeater (on rear). This function is useful when you cannot operate your TV from the remote control
because the remote control sensor of the TV is blocked by the unit.
• This function can be used while the TV remote control is using infrared signals.
• Position the unit and TV so that they are separated by at least 5 cm (2").
Follow the steps below to enable the TV Remote Repeater function.
1
Press the SETUP key.
The setup menu is displayed.
TV remote control sensor
2
Use S/T key to select “Function”, and then press
the ENTER key.
3
Use S/T key to select “TV Remote Repeater”, and
then press the ENTER key.
4
Use S/T key to select “On”, and then press the
ENTER key.
5
Press the SETUP key to exit the setup menu.
TV remote control
/
ENTER
SETUP
HDMI
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
TV Remote Repeater
SETTINGS
➤ Operating a TV via the TV Remote Repeater function of the unit
En
58
Updating the unit’s firmware
New firmware that provides additional features or product
improvements will be released as needed. If the unit is connected
to the Internet, you can download the firmware via the network and
update it.
When the unit is turned on for the first time after a new version of the
unit’s firmware has been released, a message indicating that a
firmware update is available will be displayed on the TV screen,
and an envelope icon ( ) will be displayed in the setup menu
(p. 48)
2
Use the S/T keys to select “Network”, and then
press the ENTER key.
3
Use the S/T keys to select “Network Update”, and
then press the ENTER key.
The following screen is displayed when firmware updates
are available.
Network Update
The unit’s firmware can be updated as follows.
Perform Update
• Update firmware from “Network Update” in the setup menu.
• Update firmware by connecting a USB flash drive to which the
unit’s firmware update has been saved (p. 60).
/
ENTER
• Update firmware using the dedicated MusicCast CONTROLLER
app installed on a mobile device. Follow MusicCast
CONTROLLER guides to operate the app and update the
firmware.
SETUP
Notes
• To cancel the operation without updating the firmware, press the SETUP
key.
4
Press the ENTER key.
The TV screen goes black and firmware update begins.
The indicators on the front panel glow to indicate progress
during the update.
• Do not operate the unit or disconnect the power cable or network cable during
firmware update. Firmware update takes about 20 minutes or more (depending
on your Internet connection speed).
• If the Internet connection speed is slow, or the unit is connected to the wireless
network, network update may not be possible depending on the condition of
the network connection. In this case, update the firmware using the USB flash
drive (p. 60).
• To perform the following procedure, your TV must be connected to the unit via
HDMI.
Update progress
• If there are multiple firmware updates, the indicators will start glowing as
each firmware update begins.
• For details on update, visit the Yamaha website.
Using “Network Update” in the setup menu
to update firmware
1
Press the SETUP key twice.
The setup menu is displayed on the TV screen.
SETTINGS ➤ Updating the unit’s firmware
En
59
5
When the indicators on the front panel glow alternately as shown
below, press the z (power) key on the unit's front panel.
4
Press the z key on the front panel while pressing the VOLUME – key
on the unit.
The firmware update will begin.
All indicators glow
The indicators on the front panel glow to indicate progress during the update.
Alternates
Update progress
• If there are multiple firmware updates, the indicators will start glowing as each firmware update
begins.
One indicator glows
The firmware update is complete.
5
When the indicators on the front panel glow alternately as shown
below, press the z (power) key on the unit's front panel.
• If the firmware update fails, the indicator at far right will flash blue. Use the z (power) key to turn the unit off
and then on again, and repeat the procedure from step 1 again. If the firmware update fails again, confirm
that the unit is properly connected to a network.
All indicators glow
Updating firmware with connection of a USB flash drive
Alternates
Download the latest firmware version from the Yamaha website to a USB flash drive,
which can then be used to update the unit’s firmware.
See information provided when updating firmware for details.
1
2
3
Save this unit’s firmware to a USB flash drive.
Turn off the unit.
Connect the USB flash drive to the UPDATE ONLY jack on the unit’s
rear panel.
One indicator glows
The firmware update is complete.
• If the firmware update fails, the indicator at far right will flash blue. Use the z (power) key to turn the unit off
and then on again, and repeat the procedure from step 1 again. If the firmware update fails again, confirm
the following.
– The USB flash drive is correctly connected to the UPDATE ONLY jack.
– See information provided as firmware updates are performed, and be sure that the USB flash drive
contains the firmware update for this unit.
– The unit is properly connected to a network.
SETTINGS ➤ Updating the unit’s firmware
En
60
Initializing the unit’s settings
Various settings for the unit can be initialized. You can choose to initialize basic unit settings (does not initialize network settings), or to initialize only network settings.
Initializing basic unit settings
Initializing network settings
The basic unit settings other than network settings will be initialized.
The following settings will be initialized.
1
2
• Settings for “Network” and “Bluetooth” in the setup menu
Turn off the unit.
• Internet radio stations assigned to the NET RADIO 1–3 keys
Hold down the z (power) key for more than 3 seconds on the front
panel of the unit.
Once settings have been initialized, the unit turns on, all indicators on the front
panel flash for a moment, and then the unit can be operated.
• Bluetooth pairing information
1
2
Turn off the unit.
Press the z (power) key while pressing the CONNECT key on the
front panel of the unit.
Once settings have been initialized, the unit turns on, all indicators on the front
panel flash for a moment, and then the unit can be operated.
• In addition to basic unit settings, the following settings will also be initialized.
– Network Standby (p. 56)
– Bluetooth function (p. 57)
• When network settings are initialized, the “Share Wi-Fi Settings (iOS)” screen will be displayed the next
time the unit is turned on (p. 18).
SETTINGS ➤ Initializing the unit’s settings
En
61
APPENDIX
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off the unit,
disconnect the AC power supply cable, and contact the nearest authorized Yamaha dealer or service center.
General
Cause
Remedy
See page
This unit does not operate
properly.
Problem
The internal microcomputer has been frozen by an external electric shock
(such as lightning or excessive static electricity) or by a power supply with
low voltage.
Disconnect the AC power supply cable from the outlet and plug it again in
after 30 seconds.
–
This unit fails to turn on when z
key is pressed (the STATUS
indicator flashes red), or the unit
is turned off soon after the power
has been turned on.
The AC power supply cable is not firmly connected to the AC wall outlet.
Connect the AC power supply cable firmly to the AC wall outlet.
The internal microcomputer has been frozen by an external electric shock
(such as lightning or excessive static electricity) or by a power supply with
low voltage.
Disconnect the AC power supply cable from the outlet and plug it again in
after 30 seconds.
This unit is suddenly turned off.
The internal temperature becomes too high and the overheat protection
circuitry has been activated.
Wait for about 1 hour for this unit to cool down, turn it back on after
confirming an adequate amount of ventilation space and not to cover this
unit with a cloth.
When the Auto Power Standby function is enabled, this unit turns off
automatically in any of the following situations:
– Audio is coming from the selected input source. However, no operations
have been performed for 8 hours or more.
– HDMI, BLUETOOTH or NET is selected as the input source, but no audio
has been input to the unit or no operations have been performed with the
unit for more than 20 minutes.
– HDMI is selected as the input source, but no playback device has been
connected to the unit’s HDMI IN jack for more than 20 minutes.
Turn on the power of the unit and play back the source again. If the Auto
Power Standby function is not used, set “Auto Power Standby” to “Off” from
the setup menu. Auto Power Standby can also be turned on or off using the
keys on the front panel. With the unit turned off, hold down the INPUT key
and press the z key, both on the front panel. The Auto Power Standby
setting will be reversed and the unit will turn on. The
indicator on the
front panel will glow for a few seconds when Auto Power Standby is
switched off, and will not glow when Auto Power Standby is switched on.
The network standby function is enabled, and the Bluetooth connection is
terminated.
Resume the Bluetooth connection using the Bluetooth device, or turn on
this unit and set “Network Standby” to “Off”.
56
Firmware update has failed.
Turn the unit off and then on again, and try updating the firmware again. If
the firmware update fails again, confirm that the unit is properly connected
to a network.
If firmware update using a USB flash drive fails, be sure that the USB flash
drive is properly connected to the UPDATE ONLY jack, and that it contains
the firmware update for this unit.
59
The indicator at far right flashes
blue.
17
–
12
52
APPENDIX ➤ Troubleshooting
En
62
Problem
No sound.
No sound or too small sound from
a specific channel.
Surround sound effects are
insubstantial.
Cause
Remedy
See page
Incorrect input or output cable connections.
Connect the cable properly.
No appropriate input source has been selected.
Select an appropriate input source with the input selector keys.
16
22
The volume is turned down.
Turn up the volume.
22
The sound is muted.
Press the MUTE or VOLUME (+/–) key to resume audio output and adjust
the volume level.
22
There is input signal cannot be played back by this unit.
Play a source whose signals can be reproduced by this unit. Change the
system settings of the source device.
72
“HDMI Audio Out” is set to “TV”.
Set to “AMP”.
51
“HDMI Control” is set to “Off”.
When connecting ARC (Audio Return Channel) supported TV and this unit
using an HDMI cable only, set “HDMI Control” to “On”.
51
To use this unit with “HDMI Control” set to “Off”, connect the TV’s audio
output jack to this unit’s TV (digital optical) jack via the optical cable.
15
Sound from an HDMI control-enabled TV is set for output from the TV’s
built-in speakers.
Use the TV’s HDMI settings to set audio output to any option other than the
TV’s built-in speakers.
The output level of the channel is muted.
Raise the output level of the channel.
Position is not properly specified.
Specify position in accordance with the unit’s installation position.
19
The source is played in stereo playback mode.
Switch to surround playback mode.
23
When connecting this unit with playback device and TV digitally, the output
setting of the playback device and TV is not valid.
Refer to the manual supplied with your device and check the setting.
–
24, 50
The playback device is set for constant output from 2 channels (PCM, etc.). Change the playback device’s audio output setting.
–
–
Position is not properly specified.
Specify position in accordance with the unit’s installation position.
19
There is no wall in the path of the sound beam.
Place the sound reflection board in the path of the sound beam.
68
No sound is coming from the
subwoofer.
The volume of the subwoofer is low.
Increase the volume of the subwoofer with the SUBWOOFER + key.
The volume of low (bass) tones
from the subwoofer is low.
The volume of the subwoofer is low.
Increase the volume of the subwoofer with the SUBWOOFER + key.
Content from an input source with a limited support for low tones is playing. Play content from an input source with broader support for low tones to see
if volume is still low.
22
22
–
APPENDIX ➤ Troubleshooting
En
63
Problem
Cause
Remedy
See page
The image is not displayed on TV
screen.
The HDMI cable is not securely connected.
Connect the HDMI cable properly.
The “This content can not be
viewed on your TV. Please
connect the TV which
corresponds to HDCP2.2 with
HDMI OUT of this unit.” message
is displayed on the TV screen and
the input source does not play.
The HDMI IN jack on the TV, which is connected to the HDMI OUT (ARC)
jack on the unit, is not compatible with HDCP 2.2.
Connect the unit to the HDMI IN jack that is compatible with HDCP 2.2 on a
TV.
Menu screen of this unit is not
displayed.
The input switch of TV is not set correctly.
Set the TV’s input source to this unit.
A digital or high-frequency
equipment produces noises.
The unit may be placed close to digital equipment or high-frequency
equipment.
Move the equipment away from the unit.
The HDMI control function does
not work properly.
“HDMI Control” is set to “Off”.
Set “HDMI Control” to “On”.
The HDMI control function is disabled on your TV.
Refer to the manual supplied with your TV and check the setting.
–
The number of the connected HDMI devices exceeds the limit.
Disconnect some of the HDMI devices.
–
The TV does not support the audio delay auto adjustment feature.
Adjust timing of sound output manually from “Audio Delay”.
Audio delay control function is
not effective even “Audio Delay”
is set to “Auto”.
15, 16
15
18
–
51
50
Bluetooth
Problem
Cause
Remedy
See page
Cannot make the unit paired with the Bluetooth device.
Receiving/transmitting
Receiving
Transmitting
“Bluetooth” is set to “Off”.
Set it to “On”.
57
The device does not support A2DP.
Perform paring operations with a device which supports A2DP.
71
The unit and device are too far apart.
Position the Bluetooth device so that it is less than 10 m (33 ft) from this unit
and pair the device with this unit.
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
Another Bluetooth device is connected.
Terminate current Bluetooth connection, and perform pairing with the new
device.
28
Bluetooth is not selected as the input source.
Select Bluetooth as the input source.
22
A Bluetooth adaptor, etc. that you want to pair with the unit has a password
other than “0000”.
Use a Bluetooth adaptor, etc. whose password is “0000”.
“Transmission” is set to “Off”.
Set it to “On”.
27, 29
–
27
57
APPENDIX ➤ Troubleshooting
En
64
Problem
Cause
Remedy
See page
Cannot make a Bluetooth connection.
Receiving/transmitting
Transmitting
“Bluetooth” is set to “Off”.
Set it to “On”.
57
Another Bluetooth device is connected.
The unit cannot make multiple Bluetooth connections. Terminate current
Bluetooth connection, and make connection for the desired device.
28
More than 20 devices are paired and the oldest pairing information is
deleted.
Perform pairing again. The unit can be paired with up to 20 Bluetooth
devices for receiving and transmitting audio. If a new device is successfully
paired with the unit after 20 other devices have already been paired, the
device with the earliest connecting date will have been unpaired to make
room for the new device.
27
Terminate AirPlay playback and try again to establish a connection.
30
Attempted to establish a connection during playback with AirPlay.
No sound is produced or the sound is intermittent during playback.
Receiving/transmitting
Receiving
Transmitting
The Bluetooth connection of the unit with the device is disconnected.
Perform Bluetooth connection operations again.
The unit and device are too far apart.
Move the Bluetooth device so that it is less than 10 m (33 ft) from this unit.
28
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
The device’s Bluetooth function is off.
Enable the Bluetooth function of the device.
The device’s volume is set to minimum.
Turn up the volume level on the device.
–
The device is not set to send Bluetooth audio signals to the unit.
Check that the Bluetooth function of the device is set properly.
–
Playback on the device has not been performed.
Perform playback on the device.
Transmitted audio does not play.
Play audio from the device selected with the input selector key.
27, 29
–
–
–
30
Remote control
Problem
The remote control does not work
and/or function properly.
The TV cannot be operated
using the TV Remote
Repeater function.
Remedy
See page
The wrong distance or angle.
Cause
The remote control functions within a maximum range of 6 m (20 ft) and no
more than 30 degrees off-axis from the front panel.
4
Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this unit.
Reposition this unit.
–
The batteries are weak.
Replace all batteries.
4
The TV Remote Repeater function is disabled.
Enable the TV Remote Repeater function.
58
A remote control using technology other than infrared is used (this unit may
not support some infrared remote controls).
The TV Remote Repeater function cannot be used. Move the unit so that it
does not block the remote control sensor on the TV, and use the TV’s remote
control to operate the TV.
–
The unit and TV are too close together or too far apart.
Move the unit away from the TV more than 5 cm (2").
12
The unit’s power cable is unplugged.
Plug in the power cable.
17
There is an object, such as a power cable, between the unit and TV.
Remove the obstacle.
–
APPENDIX ➤ Troubleshooting
En
65
Network
Problem
Cause
Remedy
See page
The network feature does not
function.
The network parameters (IP address) have not been obtained properly.
“Not connected” is displayed with
“Wireless (Wi-Fi)” configuration;
unable to connect to wireless
router (access point).
The wireless router’s MAC address filter is enabled.
“Not connected” is displayed with
“Wireless (Wi-Fi)” configuration
using the WPS function (“WPS
Button” and “PIN Code”) and
“Access Point Scan”; unable to
connect to wireless router
(access point).
The wireless router (access point) does not broadcast its SSID.
“Not connected” is displayed with
“Wireless (Wi-Fi)” configuration
using the WPS function (“WPS
Button” and “PIN Code”); unable
to connect to wireless router
(access point).
The wireless router (access point) uses WEP encryption.
Playback stops unexpectedly and
files cannot be played
continuously.
The folder contains some files that cannot be played via the unit.
The unit does not detect the PC.
The media sharing setting is not correct.
Configure the sharing setting and select the unit as a device to which music
contents are shared.
Some security software installed on your PC is blocking the access of the
unit to your PC.
Check the settings of security software installed on your PC.
The unit and PC are not in the same network.
Check the network connections and your router settings, and then connect
the unit and the PC to the same network.
–
The MAC address filter is enabled on the unit.
In “MAC Address Filter” in the setup menu, disable the MAC address filter
or specify the MAC address of your PC to allow it to access to the unit.
55
The files are not supported by the unit or the media server.
Use the file format supported by both the unit and the media server.
The files in the PC cannot be
viewed or played back.
Enable the DHCP server function on your router and set “DHCP” in the
setup menu to “On” on the unit. If you want to configure the network
parameters manually, check that you are using an IP address which is not
used by other network devices in your network.
A connection cannot be established if the wireless router’s MAC address
filter is enabled. Check wireless router (access point) settings and try a
different connection method.
55
31, 32
A connection cannot be established if the wireless router (access point) is
configured so that it does not broadcast its SSID. Check wireless router
(access point) settings and try a different connection method.
34, 35, 39
A connection cannot be established using the WPS function. Try a different
connection method.
34, 39
Delete or move files (including video or hidden files) that cannot be played
via the unit from the folder.
–
42
–
42
APPENDIX ➤ Troubleshooting
En
66
Problem
Cause
Remedy
See page
The selected Internet radio station is currently not available.
There may be a network problem at the radio station, or the service may
have been stopped. Try the station later or select another station.
–
The selected Internet radio station is currently broadcasting silence.
Some Internet radio stations broadcast silence at certain of times of the day.
Try the station later or select another station.
–
Access to the network is restricted by the firewall settings of your network
devices (such as the router).
Check the firewall settings of your network devices. The Internet radio can
be played only when it passes through the port designated by each radio
station. The port number varies depending on the radio station.
–
In “MAC Address Filter” in the setup menu, disable the MAC address filter
or specify the MAC address of your mobile device to allow it to access to
the unit.
55
The unit and mobile device are not in the same network.
Check the network connections and your router settings, and then connect
the unit and mobile device to the same network.
–
Firmware update via the
network (Network Update)
fails.
It may not be possible depending on the condition of the network.
Update the firmware via the network (Network Update) again or use a USB
flash drive.
The iPod does not recognize
the unit when using AirPlay.
The unit and iPod/mobile device are connected to different SSIDs on the
same access point.
The Internet radio cannot be
played.
The MAC address filter is enabled on the unit.
The dedicated apps for
mobile device does not detect
the unit.
Connect them to the same SSID.
–
The app installed on a mobile
device does not recognize the
unit.
The unit cannot connect to
the Internet via a wireless
router (access point).
Wireless network is not
found.
59
The wireless router (access point) is turned off.
Turn on the wireless router (access point).
–
The unit and the wireless router (access point) are too far apart.
Place the unit and the wireless router (access point) closer to each other.
–
There is an obstacle between the unit and the wireless router (access
point).
Move the unit and the wireless router (access point) in a location where
there are no obstacles between them.
–
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
Access to the network is restricted by the firewall settings of the wireless
router (access point).
Check the firewall setting of the wireless router (access point).
–
–
APPENDIX ➤ Troubleshooting
En
67
When surround effect is not enough
The unit achieves its surround sound effects by projecting sound beams which reflect
off walls. The sound beams are not reflected toward to the listening position caused by
furniture, etc., in the path of sound beams, or the room shape. In this case, the sound
may become unbalanced.
How to install YRB-100
The unit outputs sound beams according to the “Position” settings (p. 19) as shown in
the following illustrations.
Install the YRB-100 in the path of the sound beam.
shows the recommended install position.
FL: Front left
FR: Front right
SL: Surround left
SR: Surround right
Figure 1. Ideal condition
Figure 2. Surround right beam is not
being reflected because there
is no wall.
Surround right is quieter than surround
(left), or surround right is in front of its
proper location.
Position: Center
If the sound beams are not reflected toward to the listening position (figure 2), you can
adjust for this by installing the optional sound reflection board YRB-100.
Figure 3. With a sound reflection board
installed
The sound beam for surround right is
reflected correctly, and correct surround
sound effect is achieved.
Position: Left
Position: Right
• After installing the sound reflection board, refer to the YRB-100 owner’s manual to
adjust the height and angle. Playing test-tones from “Channel Level” in the setup
menu is recommended when adjusting the board (p. 50).
• By installing the board close to your listening position, you can achieve clear surround
sound positioning.
Note
• YRB-100 may not be available in some countries or regions.
• This unit does not have the function to automatically adjust sound beam angles. It is not necessary to
adjust the sound beam angles, although the procedure is described in the owner’s manual.
APPENDIX ➤ When surround effect is not enough
En
68
Basic Knowledge of Surround Sound
What is Surround Sound?
What is a Digital Sound Projector?
Yamaha’s Audio Technologies
Surround sound offers the sense of being surrounded by sounds, an
experience common in concert halls and movie theaters. This can be
achieved by surrounding the audience with numerous speakers from
which sound is output uniformly in all directions. This “surround
sound” technology immerses the listener in sound with speakers
positioned not only in front of the listener, but also behind and to the
sides of the listener, making him or her feel as if they are actually in
the situation.
For precise directional control and quality of sound reproduction,
sounds must be split into separate audio channels for output to each
speaker. Surround sound systems for regular home use (5.1-channel
speaker systems) produce surround sound using five speakers and
a subwoofer, as shown below:
A digital sound projector separately controls compact speakers
installed in orderly rows, so that optimized audio signals are output
from each speaker and synthesized as highly focused sounds
(sound beams).
This unit features many more functions based on Yamaha’s superior
audio technologies.
Typical 5.1 channel speaker system
Digital amplifier
Speaker
CINEMA DSP
Sound beams are emitted
in the target direction
Front speakers
Subwoofer
Center
speaker
Compressed Music Enhancer
This technology enhances and extends bass and treble, which tend
to be weak in digitally compressed formats such as MP3 used with
portable digital audio players and computers. This makes
compressed audio sound more musically dynamic.
With this unit, Compressed Music Enhancer is automatically
activated when audio is input from a Bluetooth device.
When these focused sounds hit a hard wall, they are reflected off of
the wall. A digital sound projector outputs sound beams from five
channels, including front (left/right), center, and surround (left/right)
channels, by reflecting these beams off of walls so that sounds reach
the listener from the appropriate direction. It features a technology
that enables true surround sound without requiring the installation of
speakers in front of, or behind, the listener.
This technology enables precise digital recreation of actual acoustic
environments found in well-known concert halls and movie theaters.
This is achieved using Yamaha’s exclusive sound field programs,
which are based on data measured in various sound fields, and with
which the amplitude, depth, and volume of sounds have been
adjusted.
Clear Voice
This technology enables clear playback of speech (dialog,
narrations, etc.) while maintaining the quality of background sound
(music, sound effects, etc.). It enhances the acoustic characteristics
of speech sounds and increases the perceived volume level.
Surround speakers
As explained above, sounds can be reproduced for a great sense of
presence by installing multiple speakers. However, this can be
difficult to do in a living room. This unit utilizes “digital sound
projector” technology to provide a realistic and engaging surround
sound experience using only a slim center unit and subwoofer.
APPENDIX ➤ Basic Knowledge of Surround Sound
En
69
Glossary
Audio/video information
Sampling Frequency and Bit Depth
These are values that represent the amount of information used to convert analog signals to digital signals.
They may be expressed as 48kHz/24bit, for example.
• Sampling Frequency
This defines the number of samples per second (sampling a finite set of discrete values in an analog
signal). The higher the sampling rate, the broader the range of frequencies that can be played back.
• Bit Depth
This defines the amplitude value of sounds when quantifying analog signals as finite values. The higher
the bit depth, the deeper sounds are reproduced.
Deep Color
This is a video technology supported by the HDMI standard. It processes RGB or YCbCr signals at bit
depths of 10, 12, or 16 bits per color, whereas conventional formats utilize only 8-bit processing, enabling
reproduction of more colors. Its gamut is comprised of a billion or more colors, while the gamuts of
conventional formats are comprised of only millions of colors or less. This broader gamut results in more
precise reproduction of colors and greater detail in darker portions.
Dolby Digital
This is a compressed audio format for 5.1 channels. It was developed by Dolby Laboratories, and is widely
used with DVD discs.
MPEG-4 AAC
An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio streaming
services on Internet because it allows a high compression rate of data while maintaining better audio quality
than MP3.
Pulse Code Modulation (PCM)
This technology records analog audio signals in digital form, converts analog audio signals to digital audio
signals, and transmits analog audio signals in digital form. It is the underlying technology for all digital audio
signal systems, and is widely used with CDs, Blu-ray Discs, and many other types of media as a
uncompressed audio format known as Linear PCM.
WAV
Windows standard audio file format, which defines the method of recording the digital data obtained by
converting audio signals. By default, the PCM method (no compression) is used, but you can also use other
compression methods.
WMA (Windows Media Audio)
One of the compressed digital audio formats developed by Microsoft Corporation. With psychoacoustic
technologies, this compression method achieves a high compression rate. Reportedly, it is capable of
compressing data quantity by about 1/20 maintaining a certain level of audio quality.
x.v.Color
This is a color space supported by HDMI. It has become an international standard for video and offers a
broader gamut than does the sRGB standard for expression of colors never before possible. It expands the
color space while ensuring compatibility with the sRGB standard for more natural and vivid images.
Dolby Pro Logic II
This technology converts audio signal recorded in 2 channels to 5-channel signal.
DTS Digital Surround
Network information
This is a compressed audio format for 5.1 channels developed by DTS. It is widely used with DVD discs.
SSID
FLAC
SSID (Service Set Identifier) is a name that identifies a particular wireless LAN access point.
FLAC is a file format for lossless audio data compression. FLAC is inferior to lossy compressed audio
formats in compression rate but provides higher audio quality.
Wi-Fi
HDMI
High-Definition Multimedia Interface (HDMI) is a digital audio/video interface that has become an industry
standard around the world. It is capable of transmitting both digital video and audio signals intact via a
single cable. It is also compliant with the High-bandwidth Digital Content Protection (HDCP) standard. See
http://www.hdmi.org for more information.
MP3
Wi-Fi is a technology that allows an electronic device to exchange data or connect to the Internet wirelessly
using radio waves. Wi-Fi offers the advantage of eliminating the complexity of making connections with
network cables by using wireless connection. Only products that complete Wi-Fi Alliance interoperability
tests can carry the “Wi-Fi Certified” trademark.
WPS
WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance, which allows easy
establishment of a wireless home network.
One of the compressed digital audio format used by MPEG. With psychoacoustic technologies, this
compression method achieves a high compression rate. Reportedly, it is capable of compressing data
quantity by about 1/10 maintaining a certain level of audio quality.
APPENDIX ➤ Glossary
En
70
Specifications
Item
Amplifier
Maximum Rated
Output Power
Type
Array
speakers
Driver
Frequency
Response
Impedance
Type
Driver
Subwoofer
Decoder
Acoustic suspension type
Full range
2.8 cm (1-1/8") cone magnetic shielding type x 8
500 Hz to 22 kHz
Bluetooth version
Ver. 2.1 +EDR
Supported
protocols
A2DP, AVRCP
Supported codecs
Bluetooth
4Ω
Bass reflex type
Receiving: SBC, MPEG-4 AAC
Transmitting: SBC
Wireless output
Bluetooth Class 2
Maximum
communication
distance
10 m ([33 ft] without obstructions)
Supported content
protection method
8.5 cm (3-1/4") cone non-magnetic shielding type x 2
SCMS-T (receiving)
Impedance
6Ω
Power Supply
PCM (5.1ch), Dolby Digital, DTS Digital Surround
Power
Consumption
25 W
Supported audio
signal (TV, BD/
DVD)
Digital (Optical)
Analog
(RCA/monaural)
1 (HDMI IN)
1 (TV)
1 (ANALOG)
1 (SUBWOOFER OUT)
1
UPDATE ONLY
1
Compatible with DLNA ver. 1.5
AirPlay supported
Internet Radio
Wireless LAN
Standards
Dimensions
(W x H x D)
With antenna: 1000 x 134 x 152 mm (39-3/8" x 5-1/4" x 6")
Without antenna: 1000 x 65 x 130 mm (39-3/8" x 2-1/2" x 5-1/8")
4.7 kg (10.4 lbs)
Weight
Specifications are subject to change without notice.
IEEE802.11b/g/n
Radio Frequency
Band
2.4 GHz
WPS (Wi-Fi
Protected Setup)
Push-Button-Method, PIN Method
Security Type
Standby Power
Consumption
• HDMI Control Off, Network Standby Off............... 0.4 W
• HDMI Control On, Network Standby Off .............. 1.5 W
• HDMI Control Off, Network Standby On
(Wired/Wi-Fi/Wireless direct/Bluetooth)
........................................................... 1.9/1.8/2.0/1.9 W
• HDMI Control On, Network Standby On .............. 3.0 W
General
1 (HDMI OUT (ARC))
NETWORK
Network
Wireless LAN
(Wi-Fi)
Subwoofer 30 W x 2
Wireless Direct
U.S.A. and Canada models: AC 120 V, 60 Hz
China model: AC 220 V, 50 Hz
Taiwan model: AC 110-120 V, 50/60 Hz
Other models: AC 220-240 V, 50/60 Hz
HDMI
Other Jacks
Array speakers 2 W x 8
50 Hz to 500 Hz
Analog
(RCA/stereo)
Output Jacks
Direct connection with mobile
devices
Frequency
Response
HDMI
Input Jacks
Specifications
WEP, WPA2-PSK (AES), Mixed Mode
APPENDIX ➤ Specifications
En
71
Available signal information
❑ Repeatable video signals
HDMI signal compatibility
This unit is compatible with the following video signals.
❑ Receivable audio signals
Audio signal types
Audio signal formats
• Deep Color
Compatible media
• x.v.Color
2ch Linear PCM
2ch, 32–192 kHz, 16/20/24 bit
CD, DVD-Video, DVD-Audio, etc.
• 3D video signal
Multi-ch Linear PCM
6ch, 32–192 kHz, 16/20/24 bit
DVD-Audio, Blu-ray disc, HD DVD,
etc.
This unit is compatible with the following resolutions.
Bitstream
Dolby Digital, DTS
DVD-Video, etc.
• VGA
• 720p/60 Hz, 50 Hz
• 480i/60 Hz
• 1080i/60 Hz, 50 Hz
• Refer to the supplied instruction manuals of the input source device, and set the device appropriately.
• 480p/60 Hz
• 1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
• When CPPM copy-protected DVD-Audio is played back, video and audio signals may not be output
depending on the type of the DVD player.
• 576i/50 Hz
• 4K/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
• This unit is not compatible with HDCP-incompatible HDMI or DVI devices. Refer to the supplied instruction
manuals of HDMI or DVI devices for HDCP compatibility.
• 576p/50 Hz
• To decode audio bitstream signals on this unit, set the input source device appropriately so that the device
outputs the bitstream audio signals directly (does not decode the bitstream signals on the device). Refer to
the supplied instruction manuals for details.
• The resolution of transmitted video signal varies according to specifications of the TV connected to this
unit.
Digital audio signal (optical)
Audio signal types
Audio signal formats
Compatible media
2ch Linear PCM
2ch, 32–96 kHz, 16/20/24 bit
CD, DVD-Video, DVD-Audio,
etc.
Bitstream
Dolby Digital, DTS
DVD-Video, etc.
APPENDIX ➤ Specifications
En
72
Windows™
The “
” logo and “Cinema DSP” are registered
trademarks of Yamaha Corporation.
®
The Bluetooth word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha
Corporation is under license.
Bluetooth
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol together are registered
trademarks, and DTS Digital Surround is a trademark of DTS, Inc.
© DTS, Inc. All Rights Reserved.
“HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface”
are trademarks, or registered trademarks of HDMI Licensing LLC.
Bluetooth is a technology for wireless communication employing the
2.4 GHz frequency band, which can be used without a license.
Windows is a registered trademark of Microsoft Corporation in the
United States and other countries.
Internet Explorer, Windows Media Audio and Windows Media Player
are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Android™
Android is a trademark of Google Inc.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a radio
band shared by many types of equipment. While Bluetooth
compatible devices use a technology minimizing the influence of
other components using the same radio band, such influence may
reduce the speed or distance of communications and in some
cases interrupt communications.
• The speed of signal transfer and the distance at which
communications is possible differs according to the distance
between the communicating devices, the presence of obstacles,
radio wave conditions and type of equipment.
• Yamaha does not guarantee all wireless connections between this
unit and devices compatible with Bluetooth function.
iTunes, AirPlay, iPad, iPhone, iPod, and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries.
“x.v.Color” is a trademark of Sony Corporation.
MusicCast is a trademark or registered trademark of Yamaha
Corporation.
The Wi-Fi CERTIFIED Logo is a certification mark of Wi-Fi Alliance.
The Wi-Fi Protected Setup Identifier Mark is a certification mark of
Wi-Fi Alliance.
Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi Protected Setup, WPA
and WPA2 are trademark or registered trademark of Wi-Fi Alliance.
“Blu-ray Disc™”, “Blu-ray™”, and the logos are trademarks of the
Blue-ray Disc Association
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in some
sections. You have the right to obtain, duplicate, modify, and
redistribute this open-source code only. For information on GPL/
LGPL open source software, how to obtain it, and the GPL/LGPL
license, refer to the Yamaha Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
Bluetooth protocol stack (Blue SDK)
DLNA™ and DLNA CERTIFIED™ are trademarks or registered
trademarks of Digital Living Network Alliance. All rights reserved.
Unauthorized use is strictly prohibited.
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
APPENDIX ➤ Specifications
En
73
Index
Numerics
2-channel playback
3D video 15
4K video 15
5.1-channel 69
23
A
Access point scan 35
AirPlay 45
Antenna 9, 13
App HOME THEATER CONTROLLER (WLAN) 6
App MusicCAST CONTROLLER 6
Audio assign 51
Audio information 24
Audio input signal information 53
Audio Return Channel (ARC) 15
Auto power standby 52
Delay between video and audio output 50
DHCP 31, 55
DLNA 42
DNS server (P) 54, 55
DNS server (S) 54, 55
Dolby Digital 70
Dolby Pro Logic II 70
DTS Digital Surround 70
Dynamic range 50
E
Encryption method 34, 37, 39, 40
F
File format (computers/NAS) 42
Firmware update 56, 59
Firmware version 53
B
H
Bit depth 70
Bluetooth 26
Bluetooth (receiving audio) 27
Bluetooth (transmitting audio) 29
Bluetooth function (on/off) 57
Brightness of indicators 52
HDCP version 2.2 15
HDMI 70
HDMI audio out 51
HDMI cable 15, 16
HDMI control 20, 51
I
C
Channel level 50
CINEMA DSP 23
Compressed Music Enhancer 69
D
Deep Color 70
Default gateway 54, 55
Indicators 7, 8
Information (audio/video/firmware) 53
Initialization 61
Installation (Mounting the unit on a wall) 14
Installation position of the unit 19
Internet radio 43
IP address 54, 55
iPod music (AirPlay) 45
iTunes music (AirPlay) 45
L
Language (OSD)
19
M
MAC address 54
MAC address filter 31, 55
Manual setting (wireless connection)
Media sharing setup 42
Menu display 18
Mobile device music 47
MP3 70
MPEG-4 AAC 70
37
N
Network information 54
Network name 56
Network standby 56
O
OSD language
52
P
Pairing 27, 29
Power cable 9, 17
Pulse Code Modulation (PCM)
70
R
Reflection board 68
Remote control 4, 10
Remote control sensor 7
S
Sampling frequency
70
APPENDIX
➤ Index
En
74
Security 54
Security key 38, 40
Security software 31
Setup menu 48
Sharing Wi-Fi settings (iOS device) 18, 33
SSID 34, 36, 54, 70
Stereo playback 23
Subnet mask 31, 54
Subwoofer volume 22, 24
Surround mode 23
Surround sound effect 19
T
Test sounds 50
TV 18, 20, 22
TV Remote Repeater 58
V
Video input signal information 53
Volume 22
Volume for each channel 24, 50
vTuner 43
vTuner ID 54
W
Wi-Fi 70
Wired network connections 17, 31
Wireless Direct 40
Wireless network 32
WPS 70
WPS PIN code 39
X
x.v.Color 70
APPENDIX
➤ Index
En
75
© 2015 Yamaha Corporation YH260A0/EN
UAB
Digital Sound Projector
Quick Reference Guide
For more detailed information, refer to the Owner’s Manual on the
CD-ROM.
Caution: Do not attempt to play this CD-ROM in an audio player.
IMPORTANT SAFETY INSTRUCTIONS
11
12
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
13
14
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert you to the presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert you to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
10
2
En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of
time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain this Owner's Manual in a safe place
for future reference.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group
want you to get the most out of your equipment by playing it at a safe level. One
that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since
hearing damage from loud sounds is often undetectable until it is too late, Yamaha
and the Electronic Industries Association’s Consumer Electronics Group recommend you to
avoid prolonged exposure from excessive volume levels.
FCC INFORMATION (for US customers)
NOTICE
1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual,
meets FCC requirements. Modifications not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
2
IMPORTANT: When connecting this product to accessories and/or another product use only
high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void your FCC authorization to use
this product in the USA.
3
NOTE: This product has been tested and found to comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides
a reasonable level of assurance that your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed and used according to the
instructions found in the users manual, may cause interference harmful to the operation of other
electronic devices.
Compliance with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be determined by
turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America A/V Division, 6600 Orangethorpe Avenue, Buena Park,
CA 90620, USA.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America
or its subsidiaries.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC
radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party:
Yamaha Corporation of America A/V Division
Address:
6600 Orangethorpe Avenue, Buena Park, CA 90620
Telephone:
714-522-9011
Type of Equipment: Digital Sound Projector
Model Name:
YSP-1600
This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS
tandard(s).
Operation is subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired
operation of this device.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert.
CAN ICES-3 (B)/NMB-3 (B)
En
3
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
4
En
To assure the finest performance, please read this manual carefully. Keep it in a safe place for future
reference.
Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight,
heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following
minimum clearances.
Top: 10 cm (4 in), Rear: 10 cm (4 in), Sides: 10 cm (4 in)
Locate this unit away from other electrical appliances, motors, or transformers to avoid humming
sounds.
Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal
injury.
Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be
exposed to liquid dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal
injury.
– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the
user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat
radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are complete.
Do not operate this unit upside-down. It may overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit with a higher voltage than
specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will
not be held responsible for any damage resulting from use of this unit with a voltage other than
specified.
To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a
wall outlet or this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any
service is needed. The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power
plug from the wall outlet.
Be sure to refer to the “Troubleshooting” section of the Owner’s Manual on the CD-ROM for
common operating errors before concluding that this unit is faulty.
Before moving this unit, press A to set it to standby mode and disconnect the AC power plug from the wall
outlet.
Condensation will form when the surrounding temperature changes suddenly. Disconnect the
power cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may become warm. Turn the power off, then leave
this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. When you
dispose of batteries, follow your regional regulations.
22 Excessive sound pressure from earphones and headphones can cause hearing loss.
23 Keep the product out of reach of children to avoid them swallowing small parts.
This unit is not disconnected from the AC power source as long as it is connected to the wall
outlet, even if this unit itself is turned off by A. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or
defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical facilities.
The name plate of YSP-1600 is located on the bottom of the unit.
We, Yamaha Music Europe GmbH hereby declare that this unit is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Yamaha Music Europe GmbH
Siemensstr. 22-34 25462 Rellingen, Germany
Tel: +49-4101-303-0
■ Notes on remote controls and batteries
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places
• Insert the battery according to the polarity markings (+ and -).
• If the batteries grow old, the effective operation range of the remote control decreases considerably.
If this happens, replace the batteries with two new ones as soon as possible.
• If the batteries run out, immediately remove them from the remote control to prevent an explosion or
acid leak.
• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the
leaked material comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and
consult a doctor. Clean the battery compartment thoroughly before installing new batteries.
• Do not use old batteries together with new ones. This may shorten the life of the new batteries or
cause old batteries to leak.
• Do not use different types of batteries (such as alkaline and manganese batteries) together. Danger of explosion may
happen if batteries are incorrectly replaced. Specification of batteries may be different even though they look the
same.
• Before inserting new batteries, wipe the compartment clean.
• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor
immediately.
• When not planning to use the remote control for long periods of time, remove the batteries from the
remote control.
• Do not charge or disassemble the supplied batteries.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it
should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note
Information for Users on Collection and Disposal of Old Equipment and Used
Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical
and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/
EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European
Union]
These symbols are only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies
with the requirement set by the Directive for the chemical involved.
For more detailed information, refer to the Owner’s Manual on the CD-ROM. To view the
Owner’s Manual, click on “English” in the screen displayed automatically when you insert the
CD-ROM into your PC, or click on the model name if the screen to select models is displayed,
and then click on “English” in the next screen. Then, follow the onscreen instructions.
If the screen is not displayed automatically, open the “index.html” in the CD-ROM.
Caution: Do not attempt to play this CD-ROM in an audio player.
The Owner’s Manual contained in the CD-ROM can be downloaded from the following
website.
http://download.yamaha.com/
The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is
hazardous if engaged in a live socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
En
5
About this Quick Reference Guide
The Quick Reference Guide provides instructions for connecting a TV and BD/DVD
player to the unit, applying settings, and playing content. For more information on
operations, refer to the Owner’s Manual in the supplied CD-ROM.
Supplied accessories
Before connecting, make sure you have received all of the following items.
Read the safety instructions described in this booklet before using the unit. For
instructions on how to operate or set the external devices, refer to the owner’s manual
supplied with each devices.
•
indicates supplementary explanations for better use.
•
indicates precautions for use of the unit and its feature limitations.
Remote control
Batteries
Optical cable
(AAA, R03, UM-4; x2)
(1.5 m (4.9 ft))
Accessories for mounting the unit on a wall
Template
Brackets (x2)
Screws (M4 x 12mm; x4)
ANTENNA / ANTENNE
MOUNTING TEMPLATE/GABARIT DE FIXATION
DRILL HERE / PERCER CIC
DRILL HERE / PERCER CIC
457mm (18” )
457mm (18 po)
ZR85910-1
Owner’s Manual CD-ROM
Quick Reference Guide
(this booklet)
MusicCast Setup Guide
Devices and cables required for connection
• TV
6
En
Supplied accessories
• BD/DVD player
• HDMI cables (x2)
Preparing remote control
Before installing batteries or using the remote control, be sure to read battery and remote control precautions in this booklet.
Installing the batteries
Operation range
Peel off the protection sheet
before use.
Battery × 2
(AAA, R03, UM-4)
Within 6 m (20 ft)
Preparing remote control
En
7
1 2 3 4
a Installation
Place the unit on a flat surface. When installing this unit on a rack behind which there is limited space, for example, it may be easier to connect external devices to this unit first. See
page 10 for information regarding the connection of external devices.
Notes
• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.
• The unit’s speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the unit.
• Do not stack the unit directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.
Recommended place for installation
• Do not install the unit near a corner of the
room.
• The unit can be mounted on a wall. See
page 14 in the Owner’s Manual.
Position the unit and TV so that they are separated
by at least 5 cm (2").
Use the TV Remote Repeater function if the unit
obstructs the remote control sensor on the TV.
See page 58 in the Owner’s Manual.
• When raising the antenna (p. 9), position the
unit so that the antenna does not obstruct
the TV screen.
• The listening position (such as sofa, etc.)
should be located at the front of the unit.
• The distance between the listening position
and the unit should be more than 2 m (6.6 ft).
8
En
a Installation
To achieve the optimal surround sound
effects, be sure that obstacles such as
furniture may not obstruct the path of
sound beams (p. 9).
1 2 3 4
❑ Unit installation position and surround sound effects
Raising the antenna
The unit achieves surround sound by reflecting sound beams off walls.
Raise the antenna on the rear panel of the unit when connecting a wireless router
(access point) to use a network.
Hold the base of the
antenna while raising it
to its upright position.
Effective surround effect may not be achieved in the following environment.
• Sound beams are blocked by obstacles such as furniture.
• The room size is not within the following dimensions;
Width: 3 meters to 7 meters (9.8 ft to 23 ft)
Depth: 3 meters to 7 meters (9.8 ft to 23 ft)
Height: 2 meters to 3.5 meters (6.6 ft to 11.5 ft)
• Listening position is too close to the unit.
• Do not apply excessive force on the antenna. Doing so may damage it.
• Be sure to check the direction in which the antenna moves, and angle it in the proper direction.
• The unit is installed too close to the left or right wall.
• Do not remove the antenna.
• The unit is installed in the corner of the room.
• There is no wall for reflecting sound beam on the path of the sound beams.
• For details on the wireless connection, refer to page 32 in the Owner’s Manual.
• The optimum surround sound effect is achieved by setting a position according to the installation position of
the unit. For details, refer to “c Surround sound effect for the installation position” (p. 12).
a Installation
En
9
1 2 3 4
b Connections
Connecting a TV and BD/DVD player
For the cable connection, follow the procedure below. See page 16 in the Owner’s Manual when connecting other playback devices such as a game console.
TV
1
HDMI cable (optional)
The digital audio/video signals from the BD/DVD
player are input to this unit.
Video signals
Audio signals
HDMI INPUT
2
1
OPTICAL
OUTPUT
3
2
HDMI cable (optional)
Digital video from the BD/DVD player is displayed on
the TV.
Use an optical cable
when connecting a TV
that does not support
Audio Return Channel.
BD/DVD player
HDMI
OUTPUT
• This unit supports HDCP version 2.2, a copy protection technology.
To enjoy playback of 4K video, connect the unit to the HDMI IN jack
(one compatible with HDCP 2.2) on an HDCP 2.2-compliant TV.
1. Remove the cap
3
1
2
2. Check the direction of the
plug
To an AC wall outlet
Audio Return Channel (ARC) supported TV
• Connect an HDMI cable to the audio return channel supported jack (the
jack with “ARC” indicated) on TV.
• Enable the HDMI control function of this unit to activate the Audio Return
Channel (ARC). See page 51 in the Owner’s Manual.
What is Audio Return Channel (ARC)?
HDMI
IN
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
HDMI
IN
3
10
En
b Connections
To an AC wall outlet
OUT(ARC)
NETWORK
TV
ANALOG SUBWOOFER OUT UPDATE ONLY
• A function transmits digital audio signal output from TV to this unit through
an HDMI cable. By this function, an optical cable to connect TV and this unit
is not needed.
For a wired network connection, connect one end of the
network cable to the NETWORK jack on the rear panel of the
unit and the other end to a router. For details, see page 31 in
the Owner’s Manual.
1 2 3 4
Turning on the unit
1
Press the z key.
Connecting the unit to a wireless network
When the unit is turned on for the first time after purchase,
the
indicator on the front panel will flash slowly. The
screen below will be displayed on the TV when the TV is
turned on.
1
Press the ENTER key.
The screen below is displayed.
Share
Share
Y
(
n
u
l
Flashes slowly
ENTER
RETURN
o
W
e
s
a
u
i
t
i
t
w
n
e
c
F
o
g
r
an
i)
rk
a
.
s
s
w
d
Wi-Fi
h
e
i
e
a
t
t
v
Wi-Fi
Settings
Settings
M
c
n
W
y
re the wireless
tings of the
h Sound Projector
ice with iOS7 or
[ENTER]:Start
[RETURN]:Cancel
[
]:OSD Language
• When the screen is not displayed, use the input button on the TV’s remote control
to switch input so that video input from this unit is displayed. When this unit is
connected to the TV as shown on page 10, select “HDMI 1”.
• The language used for menu display (OSD Language) can be selected from the
screen shown above. Use the W/X key to select the language, and follow the
on-screen instructions. The OSD language can also be changed from the setup
menu at any time. Press and hold the SETUP key until the “OSD Language” menu
is displayed on the TV, and use the S/T key to select the language. Press the
SETUP key to exit the setup menu.
While this screen is displayed, an iOS device (such as an iPhone)
can be used to easily connect the unit to a wireless network. Follow
the procedure “Connecting the unit to a wireless network” on this
page.
a
o
e
i
o
k
n
t
u
e sure your i
nected to you
work, and the
Fi settings s
r iOS device.
OS device is
r Wi-Fi
n open the
creen of
[ENTER]:Confirm
[RETURN]:Cancel
• You need iOS device with iOS 7.1 or later.
• Before proceeding, confirm that your iOS device is connected to a wireless
router (access point).
2
3
Press the ENTER key.
Display the Wi-Fi setup screen on the iOS device
and select the unit from “SETUP A NEW AIRPLAY
SPEAKER...”.
iOS (an example of English version)
If you will not use an iOS device to connect to a wireless network,
press the RETURN key and proceed to “c Surround sound effect
for the installation position”.
The name of the unit
• This screen will not be displayed and the
indicator will not flash if the unit is
connected to a router via its NETWORK jack (wired connection).
• See page 31 in the Owner’s Manual for wireless network connection methods
other than “Share Wi-Fi Settings”, or for more information regarding wired and
wireless networks.
b Connections
En
11
1 2 3 4
4
Select the network (access point) of which you want to share the
settings with the unit.
c Surround sound effect for the installation
position
iOS (an example of English version)
Tap here to start setup
The network currently selected
The name of the unit
The surround sound is achieved by reflecting the sound beams off walls as shown in
the illustration below. For optimum surround effect, turn on the unit and select the
POSITION key according to the installation position of the unit.
1
Hold down the POSITION key that corresponds to the installation
position of the unit for more than 3 seconds.
The indicators on the front panel flash according to the set position.
Left
Center
• You can use this function to connect to a wireless network at any time by selecting “Share Wi-Fi Settings
(iOS)” from the setup menu. However, be aware that if a different wireless network, or a Bluetooth device,
has already been configured, doing so will erase any previous settings.
12
En
c Surround sound effect for the installation position
Right
L (Left)
C (Center; default setting)
R (Right)
Left side of room
Center of room
Right side of room
1 2 3 4
d Playback
Enjoying TV
1
2
5
The number of lighted indicators increases when the volume is turned
up, and decreases when the volume is turned down.
Press the TV key.
• When audio is output from the TV speaker, set TV’s audio output to any option
other than TV. See the instructions manual of TV for more information.
TV
• HDMI control function
You can use the TV remote control to operate this unit if your TV supports the
HDMI control function. See page 20 in the Owner’s Manual.
Volume down (–)
6
Volume up (+)
Press one of the surround mode keys according to
your preferences.
See page 23 in the Owner’s Manual for details.
Playing a DVD or BD
The following explains the playback procedure when this unit is
connected to the TV and BD/DVD player as shown in “Connecting
a TV and BD/DVD player” (p. 10).
VOLUME
(+/-)
When the volume is adjusted, indicators on the front panel
indicate volume level.
Select the desired TV channel.
HDMI
Surround
mode keys
Press the VOL (+/-) key to adjust the volume.
1
Turn on the TV and BD/DVD player connected to this
unit.
2
Press the HDMI key to select the BD/DVD player as
the input source.
When this unit does not play back, check the following
• The unit and BD/DVD player are connected correctly.
• The audio output settings of the BD/DVD player is set to digital sound output
(bitstream).
• The TV’s input is switched to this unit.
Indicator on the front panel
Glows
3
4
Use the TV’s remote control to switch the TV’s input
to HDMI 1.
Play back a DVD or BD on the BD/DVD player.
The unit is equipped with a number of other functions not
described in this booklet. See the Owner’s Manual for details.
Main features
• The ability to play audio from a Bluetooth device
• The ability to play an audio source over a network
• Dedicated MusicCast CONTROLLER and HOME THEATER
CONTROLLER (WLAN) apps
d Playback
En
13
AVEG1A1102C
Important Notice:Guarantee Information for
customers in EEA* and Switzerland
English
For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland
warranty service, please either visit the website address below (Printable file is available at our
website) or contact the Yamaha representative office for your country. *EEA:European
Economic Area
http://europe.yamaha.com/warranty/
© 2015 Yamaha Corporation
Printed in Indonesia ZS68070
YSP-1600 Firmware Update Version 2.19
Yamaha is pleased to offer the following firmware update to ensure the best possible performance and
latest features for your Digital Sound Projector.
This firmware
1. Enables MusicCast functions. For further information, please visit
http://www.yamaha.com/musiccast/
2. Improves wireless connectivity
CHECK THE UNIT’S FIRMWARE VERSION PRIOR TO THIS UPDATE
On the remote control, press the SETUP button.
Select “Information” > “System”. Your current firmware version is displayed on front window. If your
firmware version is 2.19 or higher, the Digital Sound Projector is already up-to-date.
If not, conduct firmware update by following the instruction.
Registered Date : 9/24/2015
Language : English
Size : 28.13 MB
■ UPDATING THE UNIT’S FIRMWARE
New firmware that provides additional features or product
improvements will be released as needed. If the unit is connected
to the Internet, you can download the firmware via the network and
update it.
4
4
Press the ENTER key.
The TV screen goes black and firmware update begins.
The firmware update will begin.
The indicators on the front panel glow to indicate progress
during the update.
When the unit is turned on for the first time after a new version of the
unit’s firmware has been released, a message indicating that a
firmware update is available will be displayed on the TV screen,
and an envelope icon ( ) will be displayed in the setup menu.
Press the key on the front panel while pressing the VOLUME – key
on the unit.
The indicators on the front panel glow to indicate progress during the update.
Update progress
Update progress
The unit’s firmware can be updated as follows.
• Update firmware from “Network Update” in the setup menu.
• If there are multiple firmware updates, the indicators will start glowing as
each firmware update begins.
• Update firmware by connecting a USB flash drive to which the
unit’s firmware update has been saved.
/
ENTER
• Update firmware using the dedicated MusicCast CONTROLLER
app installed on a mobile device. Follow MusicCast
CONTROLLER guides to operate the app and update the
firmware.
5
• If there are multiple firmware updates, the indicators will start glowing as each firmware update
begins.
5
When the indicators on the front panel glow alternately as shown
below, press the (power) key on the unit's front panel.
When the indicators on the front panel glow alternately as shown
below, press the
(power) key on theunit's front panel.
All indicators glow
All indicators glow
SETUP
Notes
Alternates
• Do not operate the unit or disconnect the power cable or network cable during
firmware update. Firmware update takes about 20 minutes or more (depending
on your Internet connection speed).
Alternates
• If the Internet connection speed is slow, or the unit is connected to the wireless
network, network update may not be possible depending on the condition of
the network connection. In this case, update the firmware using the USB flash
drive.
• To perform the following procedure, your TV must be connected to the unit via
HDMI.
• For details on update, visit the Yamaha website.
Using “Network Update” in the setup menu
to update firmware
1
One indicator glows
One indicator glows
The firmware update is complete.
The firmware update is complete.
• If the firmware update fails, the indicator at far right will flash blue. Use the (power) key to turn the unit off
and then on again, and repeat the procedure from step 1 again. If the firmware update fails again, confirm
that the unit is properly connected to a network.
• If the firmware update fails, the indicator at far right will flash blue. Use the (power) key to turn the unit off
and then on again, and repeat the procedure from step 1 again. If the firmware update fails again, confirm
the following.
– The USB flash drive is correctly connected to the UPDATE ONLY jack
– See information provided as firmware updates are performed, and be sure that the USB flash drive
contains the firmware update for this unit.
– The unit is properly connected to a network.
Press the SETUP key twice.
The setup menu is displayed on the TV screen.
2
Use the / keys to select “Network”, and then
press the ENTER key.
3
Use the / keys to select “Network Update”, and
then press the ENTER key.
The following screen is displayed when firmware updates
are available.
• To cancel the operation without updating the firmware, press the SETUP
key.
Updating firmware with connection of a USB flash drive
Download the latest firmware version from the Yamaha website to a USB flash drive,
which can then be used to update the unit’s firmware.
See information provided when updating firmware for details.
1
2
3
Save this unit’s firmware to a USB flash drive.
Turn off the unit.
Connect the USB flash drive to the UPDATE ONLY jack on the unit’s
rear panel.
MusicCast Setup Guide
Home Audio Network with MusicCast
EN
MusicCast is a brand new wireless musical solution from Yamaha, allowing you to share music
among all of your rooms with a variety of devices. You can enjoy music from your smartphone, PC,
NAS drive and music streaming service anywhere in your house with one easy-to-use app. For more
details and a lineup of MusicCast compatible products, visit our website.
FR
DE
SV
IT
ES
NL
RU
ZH
KO
¢Key features
•
Seamlessly control all MusicCast compatible devices with the dedicated “MusicCast
CONTROLLER” app.
•
Link a MusicCast compatible device to another device in a different room and play them back
simultaneously.
•
Play back music from music streaming services. (The compatible music streaming services may
differ depending on your region and product. Refer to the product information on our website
for details.)
JA
En
1
Setting Up
¢Preparation of the devices
Mobile device (smartphone, etc.)
To use the network features on the MusicCast compatible device, you need the
dedicated app “MusicCast CONTROLLER” for the operation. Search for the free app
“MusicCast CONTROLLER” on App Store (for iOS devices) or Google Play (for Android
devices) and install it to your device.
For details, refer to the instructions for this app in each store.
Connect the mobile device in which MusicCast CONTROLLER has been installed to the wireless
router in your home.
If your router supports multiple SSID’s (network names), connect the mobile device to the first
access point (“SSID 1”, etc.)
¢Setting of the devices and playback
Create the following network (MusicCast Network) using the MusicCast CONTROLLER app.
wireless router
2
En
1 Turn on the MusicCast compatible device.
2 Tap the MusicCast CONTROLLER app icon on your mobile device and tap “Setup.”
Tip
If you have already connected a MusicCast compatible device to the network, tap “Settings” and then “Add New Device.”
3 Operate the MusicCast CONTROLLER app following the onscreen instructions, then
press and hold the CONNECT button of the MusicCast compatible device (or the
remote control) for three seconds.
Refer to the Owner’s Manual of each MusicCast compatible device for the CONNECT
button.
4 Set up the network
Operate the MusicCast CONTROLLER app following the onscreen instructions to set up
the network.
5 Operate the MusicCast CONTROLLER app to playback.
Tip
• If you want to install a MusicCast compatible device to a location that is out of range of the wireless router, connect
another MusicCast support device to the router with a network cable to extend the range (Extend mode).
Standard Mode
Extend Mode
• Depending on where it is placed, the MusicCast compatible device may not be able to play back a high-resolution audio
source. In this case, connect the device directly to the router with a network cable.
En
3
Troubleshooting
Refer also to the troubleshooting section in the relevant Owner’s Manual for the MusicCast
compatible device.
Problem/Cause
Remedy
No sound from the MusicCast compatible device.
The device is turned off.
Turn on the device.
Enable network standby on the device.
The device is not connected to the MusicCast
Connect the device with the MusicCast CONTROLLER
network.
app.
Cannot make the connection settings on the MusicCast app.
The mobile device is not connected to the wireless
router at your home.
Connect the mobile device to the wireless router and
start the MusicCast CONTROLLER app.
Disable the cellular data transmission.
The MusicCast compatible device is turned off.
Turn on the MusicCast compatible device.
Enable network standby on the device.
Cannot connect to the network.
The network parameters (IP address) have not been
obtained properly.
The setting of the wireless router has been changed.
Enable the DHCP server function on your router.
Connect all MusicCast compatible devices to the
network with the MusicCast CONTROLLER app.
The MusicCast CONTROLLER app cannot detect a MusicCast compatible device.
The mobile device is not connected to the wireless
router at your home.
Connect the mobile device to the wireless router,
and set the MusicCast compatible device with the
MusicCast CONTROLLER app again.
The MusicCast compatible device is turned off.
Turn on the device.
Enable network standby on the device.
For further information, please visit our website:
http://www.yamaha.com/musiccast/
MusicCast is a trademark or registered trademark of Yamaha Corporation.
Android and Google Play are trademarks of Google Inc.
iPhone, iPad and AirPlay are trademarks of Apple Inc., registered in the U.S. and other countries.
4
En
トラブルシューティング
取扱説明書に記載のトラブルシューティングもご覧ください。
症状 / 原因
対策
MusicCast 対応機器から音が出ない
MusicCast 対応機器の電源がオフになっている。
MusicCast 対応機器が MusicCast ネットワークに
接続されていない。
MusicCast 対応機器の電源をオンにしてください。
ネットワークスタンバイをオン
(有効)にしてください。
MusicCast CONTROLLER を使い、接続してください。
MusicCast CONTROLLER で接続の設定ができない。
モバイル端末をルーターに接 続した後、MusicCast
モバイル端末がご家庭のルーターに接続されてい
CONTROLLER で設定してください。
ない。
モバイル端末のモバイルデータ通信を無効にしてくだ
さい。
MusicCast 対応機器の電源がオフになっている。
MusicCast 対応機器の電源をオンにしてください。
ネットワークスタンバイをオン
(有効)にしてください。
ネットワークに接続できない
ネットワーク情報
(IP アドレス)が正しく取得されて
いない。
ルーターの設定が変更された。
ルーターの DHCP サーバー機能を有効にしてください。
もう一度、MusicCast CONTROLLER ですべての
MusicCast 対応機器を接続してください。
MusicCast CONTROLLER から MusicCast 対応機器が認識されない。
モバイル端 末をルーターに接 続した後、MusicCast
モバイル端末がご家庭のルーターに接続されてい
CONTROLLER で設定してください。複数の SSID を持
ない。
つルーターに接続する場合は、MusicCast 対応機器と
同じ SSID のネットワークに接続してください。
MusicCast 対応機器の電源をオンにしてください。
MusicCast 対応機器の電源がオフになっている。
ネットワークスタンバイをオン
(有効)に設定してくだ
さい。
更に詳しい情報については、以下のサイトをご覧ください。
http://www.yamaha.com/musiccast/
MusicCast はヤマハ株式会社の商標です。
Android、GooglePlay は Google Inc. の商標です。
iPhone、iPad、AirPlay は、米国およびその他の国々で登録されている Apple Inc. の商標です。iPhone 商標は、アイホン株式会
社のライセンスに基づき使用されています。
4
Ja
© 2015 Yamaha Corporation
ZS47140-1
© 2015 Yamaha Corporation ZS95440
Supplement for Pandora®
The Pandora service is available in the U.S.A., Australia
and New Zealand only.
Notes
• Configure basic settings for the MusicCast
CONTROLLER app before using the service.
• To use this function, the unit must be connected to the
Internet. For detail on connections and network
settings, refer to “Owner’s Manual”.
Pandora is a free, personalized Internet radio
service playing only music you love. Enter your
favorite artists or tracks and Pandora will bring
an effortless personal soundtrack into your living
room. Rate tracks as they play, because Pandora
caters to your tastes and adapts stations to your
feedback on the spot.
Pandora account sign-in
To start using the Pandora service on this unit,
sign in to your account using the MusicCast
CONTROLLER app installed on your mobile
device. Follow the instructions on the app
screen.
Playback of Pandora content
Use the MusicCast CONTROLLER app installed
on your mobile device to select the Pandora
service.
Since all Pandora accounts are portable, you
can always access your own personalized
Pandora stations from any computer or device in
the United States, Australia and New Zealand
that supports Pandora.
Pandora is currently only available within these
countries due to licensing restrictions.
Pandora is always free, with the option to
upgrade to Pandora One which is completely
free of all advertising and comes with additional
features.
For more information, http://www.pandora.com
Pandora, the Pandora logo, and the Pandora trade dress
are trademarks or registered trademarks of Pandora
Media, Inc. Used with permission.
© 2015 Yamaha Corporation ZS95420
Supplement for Rhapsody®
The Rhapsody® service is available in the U.S.A. only.
Prohibition
• It is strictly prohibited to modify, reproduce, reverseengineer or use this unit and/or built-in software for use
other than audiovisual purposes.
Notes
• Configure basic settings for the MusicCast
CONTROLLER app before using the service.
• To use this function, the unit must be connected to the
Internet. For detail on connections and network
settings, refer to “Owner’s Manual”.
Rhapsody® account sign-in
To start using the Rhapsody® service on this unit,
sign in to your account using the MusicCast
CONTROLLER app installed on your mobile
device. Follow the instructions on the app
screen.
Playback of Rhapsody® contents
Use the MusicCast CONTROLLER app installed
on your mobile device to select the Rhapsody®
service.
The Rhapsody® service is the power behind the
Rhapsody® Media Player (the Rhapsody® player
software that you can download to your
computer). Rhapsody® service supplies the
music, keeps My Library up to date, provides
you with Rhapsody® channels, the Playlist
Central online community, and manages your
downloads. Your software connects to
Rhapsody® service through the internet.
Because your account information and
Rhapsody® content are on servers instead of any
individual computer, your music is infinitely
portable. Much of what you see in the Display
area comes from Rhapsody® service. What you
can do with Rhapsody® service depends on your
subscription.
You can use Rhapsody® service for free, or get
even more from a paid membership. The
Rhapsody® service also brings you Rhapsody®
Online, a streamlined, internet version of
Rhapsody® that you can access from almost
anywhere. Just sign in to your Rhapsody®
account to start letting the Rhapsody® service
work for you.
For more information,
http://www.rhapsody.com/
Rhapsody and the Rhapsody logo are registered
trademarks of Rhapsody International, Inc.
© 2015 Yamaha Corporation ZS95430
Supplement to Listen to SiriusXM
Notes
• Configure basic settings for the MusicCast
CONTROLLER app before using the service.
• To use this function, the unit must be connected to the
Internet. For detail on connections and network
settings, refer to “Owner’s Manual”.
• Available functions may vary according to your location.
Service areas of Network Music Services are limited.
Service areas may change without notice.
With SiriusXM, you get over 155 SiriusXM
channels, including commercial-free music from
nearly every genre, plus the best sports, talk,
news and entertainment.
English
2349. See our Customer Agreement for
complete terms at siriusxm.com.
All fees and programming are subject to change.
You may always change your Privacy
Preferences with us. See our Customer
Agreement and Privacy Policy for complete
terms at www.siriusxm.com.
For Canadian customers
During the 30-day free trial period you will only have
access to free trial content; even if you have fully
subscribed during the trial period.
After the 30-day free trial period Canadian-based
subscribers will have access to Canadian content.
How to Access SiriusXM on this unit
Current SiriusXM Subscribers:
If you have a paid All Access subscription, or
a trial subscription to the SiriusXM All Access
package in your vehicle, use your existing
streaming username and password to log in and
listen on this unit. If you have not already set up a
username and password, download the SiriusXM
app to your smartphone or tablet and follow the
instructions to log in, or go to siriusxm.com.
If you do not have a subscription to the
SiriusXM All Access package, follow the
instructions on this unit to set up a username and
password and add streaming to your current
subscription for 30 days, at no cost.
SiriusXM account sign-in
To start using the SiriusXM service on this unit,
sign in to your account using the MusicCast
CONTROLLER app installed on your mobile
device. Follow the instructions on the app
screen.
Playback of SiriusXM content
Use the MusicCast CONTROLLER app installed
on your mobile device to select the SiriusXM
service.
If you do not have a SiriusXM subscription:
You will be offered a 30-day trial subscription to
the SiriusXM streaming service when you provide
your email and zip/postal code.
American and Canadian customers can also
contact SiriusXM by calling 1-888-539-7474 to
subscribe.
Your service will automatically stop at the end of
your trial unless you subscribe. If you do not wish
to enjoy your no-obligation trial, you can cancel it
by calling 1-866-635-2349. If you decide to
continue service after your trial, the
subscription plan you choose will
automatically renew thereafter and you will be
charged according to your chosen payment
method at then-current rates. Fees and taxes
apply. To cancel you must call us at 1-866-635-
SiriusXM and all related marks and logos are trademarks
of Sirius XM Radio Inc. and its subsidiaries. All rights
reserved.
© 2015 Yamaha Corporation ZS95460
English
Supplement for Spotify
Spotify gives you instant access to millions of songs on your mobile devices. Just hit play to stream
anything you like.
The Spotify Connect feature lets you choose music on your Spotify app and listen on your Yamaha
home entertainment system.
See spotify.com for service area information.
Connect your device to your
home Wi-Fi network
Connect the unit and your mobile or tablet to
your home Wi-Fi network as shown in the
illustration below. All devices need to be on the
same network.
Network connection (example)
Internet
Playback of Spotify contents
Start Spotify app on your mobile or tablet device,
log in to Spotify and start playing a track.
1 Tap on the Now Playing bar to reveal extra
controls and tap the Speaker icon.
2 Select the unit (network name of the unit) as
the audio output device.
Spotify app (example)
Wireless
router
Modem
The unit
Mobile or tablet device*
* iOS/Android™ apps are available as of December 2013.
For more details, visit spotify.com
• The playback screen is displayed on the TV connected to
the unit.
• To use this function, this unit and your mobile or tablet must
be connected to the Internet. For detail on connections and
network settings, refer to “Owner’s Manual”.
Get Spotify app and premium
free trial
Download the Spotify app for your mobile or
tablet from your app store, and take the Premium
free trial.
The Spotify Software is subject to third party
licenses found here:
https://developer.spotify.com/esdk-third-party-licenses/
The Spotify app and Premium account are
required. Visit spotify.com for details.
www.spotify.com/connect
Spotify and Spotify logo are registered trademarks of the
Spotify Group.
OYAMAHA
LIMITED WARRANTY ON
HOME AUDIO PRODUCTS
Thank you for selecting a YAMAHA product. YAMAHA products are designed and manufactured to provide a high level of defect-free performance. Yamaha
Corporation of America ("YAMAHA") is proud of the experience and craftsmanship that goes into each and every YAMAHA product. YAMAHA sells its
products through a network of reputable, specially authorized dealers and is pleased to offer you , the Original Owner, the following Limited Warranty, which
applies only to products that have been (1) directly purchased from YAMAHA's authorized dealers in the USA, including Puerto Rico (the "Warranted Area")
and (2) used exclusively in the Warranted Area. YAMAHA suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized
YAMAHA dealer or YAMAHA Customer Service if you have any questions.
THIS WARRANTY COVERS THE LISTED PRODUCTS AGAINST DEFECTS IN MATERIALS OR
WORKMANSHIP FOR THE NUMBER OF YEARS IDENTIFIED BELOW.
Warranty Term
Duration of Warranty from Date of
Purchase by or for the Original Owner
Type of Product
AN and Stereo Receivers, Processor and Integrated Amplifiers,
Separate Amplifiers and Preamplifiers, Tuners, CO Players and
Changers, HOD Players and Recorders, Network Players, Powered
Loudspeakers, Media Controllers and Speaker Systems purchased
individually, as a pair, or as part of an Integrated or Packaged System.
··--·-------·-··- --····- 2 years
Cassette Decks, Btu-ray Disc Players, OVO Players and Changers,
Integrated Systems (Receiver or Amplifier combined or on same
chassis with CD, DVO or Blu-ray Disc Player}, Desktop Audio Systems
(i.e. TSX and POX Series}, Multimedia Speakers, Headphones,
Earphones and Accessories.
........................ 1 year
Coverage: YAMAHA will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or otherwise fails to
conform with this warranty under normal use and service during the term of this warranty, without charge for labor or materials. Repairs may be
performed using new or refurbished parts that meet or exceed YAMAHA specifications for new parts. If YAMAHA elects to replace the product, the
replacement may be a reconditioned unit. You will be responsible for any installation or removal charges and for any initial shipping charges if the
product(s) must be shipped for warranty service. However, YAMAHA will pay the return shipping charges to any destination within the USA if the repairs
are covered by the warranty. This warranty does not cover (a) damage, deterioration or malfunction resulting from accident, negligence, misuse, abuse,
improper installation or operation or failure to follow instructions according to the Owner's Manual for this product; any shipment of the product (claims
must be presented to the carrier); repair or attempted repair by anyone other than YAMAHA or an authorized YAMAHA Service Center; (b) any unit which
has been altered or on which the serial number has been defaced, modified or removed ; (c) normal wear, battery or battery replacement and any periodic
maintenance; (d) deterioration due to perspiration, corrosive atmosphere or other external causes such as extremes in temperature or humidity; (e)
damages attributable to power line surge or related electrical abnormalities, lightning damage or acts of God; (f) RFI/EMI (lnterfererfce/noise) caused by
improper grounding or the improper use of either certified or uncertified equipment, if applicable; or (g) interference arising from the use of wireless
communication devices (e.g. 2.4 gHz cordless telephones), or other radio frequency emitting products such as microwave ovens, whether such
interference impairs the operation of the product or vice-versa. Consult the Owner's Manual for guidance on set-up procedures for minimizing the risks of
interference. Any evidence of alteration, erasing or forgery of proof-of-purchase documents will cause this warranty to be void. This warranty covers only
the Original Owner and is not transferable.
In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area. Contact your
local authorized YAMAHA dealer who will advise you of the procedures to be followed . If this is not successful, contact YAMAHA at the address,
telephone number or website shown below. YAMAHA may request that you send the defective product to a local authorized YAMAHA Servicer or
authorize return of the defective product to YAMAHA for repair. For products requiring in-home service, contact your local authorized Yamaha dealer to
arrange for service. If you are uncertain as to whether a dealer has been authorized by YAMAHA, please contact YAMAHA's Service Department at the
number shown below, or check Yamaha's website at http://usa.yamaha.com. Product(s) shipped for service should be packed securely and must be
accompanied by a detailed explanation of the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other
dated, proof-of-purchase document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be
found ineligible therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and upon receipt of
payment or acceptable arrangement for payment.
Limitation Of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD OF TIME SET
FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON
INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF
PERFORMANCES OR ANY CONSEQUENCES. YAMAHA'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT
OF THE PRODUCT, AT YAMAHA'S OPTION . SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This is the only express
warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty.
If you have any questions about service received or if you need assistance in locating an authorized YAMAHA Servicer, please contact:
OYAMAHA
CUSTOMER SERVICE
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, California 90620-1373
Telephone: 800-292-2982
http://usa.yamaha.com
Do not return any product to the above address without a written Return Authorization issued by YAMAHA.
©201 2 Yamaha Corporation of America
04/20 12 ZE38290
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement