Pioneer Elite VSX-59TXi User manual

Pioneer Elite VSX-59TXi User manual
AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-59TXi
Register your product at
www.pioneerelectronics.com
• Protect your new investment
The details of your purchase will be on file for reference in the event of an
insurance claim such as loss or theft.
• Receive free tips, updates and service bulletins on
your new product
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
Operating Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead, within
an equilateral triangle, is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D1-4-2-3_En
Thank you for buying this pioneer product.
Please read through these operating
instructions so you will know how to
operate your model properly. After you
have finished reading the instructions, put
them away in a safe place for future
reference.
WARNING – TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
D1-4-2-1_En
CAUTION
– PREVENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD.
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
ATTENTION – POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER
CETTE FICHE POLARISEE AVEC UN
PROLONGATEUR UNE PRISE DE
COURANT OU UNE AUTRE SORTIE
DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE
D2-4-4-1_EF
A DECOUVVERT.
IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND
D1-4-2-6-1_En
KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
D8-10-1-3_EF
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate
D8-10-2_En
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
D8-10-1-2_En
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and
D8-10-3a_En
televisions, use shielded cables and connectors for connections.
IMPORTANT SAFETY INSTRUCTIONS
READ INSTRUCTIONS — All the safety and
operating instructions should be read before the
product is operated.
RETAIN INSTRUCTIONS — The safety and
operating instructions should be retained for
future reference.
HEED WARNINGS — All warnings on the product
and in the operating instructions should be
adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
CLEANING — The product should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides
or other volatile liquids since they may corrode
the cabinet.
ATTACHMENTS — Do not use attachments not
recommended by the product manufacturer as
they may cause hazards.
WATER AND MOISTURE — Do not use this
product near water — for example, near a
bathtub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming
pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product
and cart combination to overturn.
VENTILATION — Slots and openings in the cabinet
are provided for ventilation and to ensure
reliable operation of the product and to protect
it from overheating, and these openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
POWER SOURCES — This product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your product dealer or local power
company.
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the
appliance should be unplugged from the outlet
when left un-used for a long period of time.
GROUNDING OR POLARIZATION
• If this product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other), it will fit into the
outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
• If this product is equipped with a three-wire
grounding type plug, a plug having a third
(grounding) pin, it will only fit into a grounding
type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding type plug.
POWER-CORD PROTECTION — Power-supply
cords should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
OUTDOOR ANTENNA GROUNDING — If an
outside antenna or cable system is connected to
the product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of
antenna-discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode. See Figure A.
LIGHTNING — For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
POWER LINES — An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can fall into such power
lines or circuits. When installing an outside
antenna system, extreme care should be taken
to keep from touching such power lines or
circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
OBJECT AND LIQUID ENTRY — Never push
objects of any kind into this product through
openings as they may touch dangerous voltage
points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the product.
SERVICING — Do not attempt to service this
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
DAMAGE REQUIRING SERVICE — Unplug this
product from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
• When the power-supply cord or plug is
damaged.
• If liquid has been spilled, or objects have fallen
into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
• If the product has been dropped or damaged in
any way.
• When the product exhibits a distinct change in
performance — this indicates a need for service.
REPLACEMENT PARTS — When replacement parts
are required, be sure the service technician has
used replacement parts specified by the
manufacturer or have the same characteristics
as the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
SAFETY CHECK — Upon completion of any service
or repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
WALL OR CEILING MOUNTING — The product
should not be mounted to a wall or ceiling.
HEAT — The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers)
that produce heat.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Fig. A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRICAL CODE
D1-4-2-2_En
CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION : THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.
D6-8-2-1_En
For U.S. and Australia Model
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to lead, a chemical known to
the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
Wash hands after handling
D36-P4_En
C67-7-3_En
We Want You Listening For A Lifetime
Selecting fine audio equipment such as the unit
you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how
you can maximize the fun and excitement your
equipment offers. This manufacturer and the
Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly,
without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing
“comfort level” adapts to higher volumes of sound.
So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your
hearing adapts.
Used wisely, your new sound equipment will
provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often
undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of
sound levels is included for your protection.
Decibel
Level Example
30
40
50
60
70
80
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock
at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, and without distortion.
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers,
thunderclap
140 Gunshot blast, jet plane
180 Rocket launching pad
Once you have established a comfortable sound
level:
• Set the dial and leave it there.
Information courtesy of the Deafness Research Foundation.
Taking a minute to do this now will help to prevent
hearing damage or loss in the future. After all, we
want you listening for a lifetime.
S001_En
If the socket outlets on the associated equipment
are not suitable for the plug supplied with the
product, the plug must be removed and appropriate
one fitted. Replacement and mounting of an AC plug
on the power supply cord of this unit should be
perfomed only by qualified service personnel. The
cut-off plug must be disposed of as an electrical
shock hazard could exist if connected to a socket
D3-4-2-2-1a_En
outlet.
The STANDBY/ON switch is secondary connected
and therefore, does not separate the unit from mains
power in STANDBY position. Therefore install the
unit suitable places easy to disconnect the MAINS
plug in case of the accident. The MAINS plug of unit
should be unplugged from the wall socket when left
D3-4-2-2-2a_En
unused for a long period of time.
Our philosophy
Dolby Pro Logic IIx and DTS Neo:6 decoders
Pioneer is dedicated to making your home theater
listening experience as close as possible to the vision of
the moviemakers and mastering engineer when they
created the original soundtrack. We do this by focusing
on three important steps:
The built-in Dolby Pro Logic IIx and DTS Neo:6 decoders
not only provide full surround sound decoding for Dolby
Surround sources, but will also generate convincing
surround sound for any stereo source.
1
Achieving the highest possible sound quality
2 Allowing for customized acoustic calibration
according to any listening area
3 Fine-tuning the receiver with the help of worldclass studio engineers1
Features
Easy setup using Advanced MCACC
Setting up for home theater sound is as easy as
connecting your speakers, a DVD player or other source,
and your TV. The Auto Surround Setup provides a quick
but accurate surround sound setup, while for complete
surround sound control you still have access to the full
range of surround sound settings.
In addition, the Profession Acoustic Calibration EQ setup
measures the reverb characteristics of your listening
area, allowing you to customize your system calibration
with the help of a graphical output that can be displayed
on-screen, or using a computer.
i.LINK digital interface
The i.LINK interface makes it possible to connect this
receiver to i.LINK-equipped components, allowing you to
enjoy high sampling rate (up to 192kHz) PCM
multichannel digital audio from DVD-Audio and SACD
discs, as well as digital audio from DVD-Video, CD and
Video CD discs, all with a single cable.
USB digital interface
It is possible to listen to multichannel audio sources from
your computer by connecting to the USB interface on the
rear of this receiver. Depending on your model of
computer and the software installed, you can listen to
any source compatible with your operating system
through the speaker setup connected to this receiver.
Dolby Digital and DTS decoding, including Dolby
Digital EX, DTS 96/24 and DTS-ES
Dolby Digital and DTS decoding brings theater sound
right into your home with up to six channels of surround
sound, including a special LFE (Low Frequency Effects)
channel for deep, realistic sound effects.
With the addition of a surround back speaker, you can
take advantage of the built-in Dolby Digital EX and DTSES decoders for six-channel surround sound.
THX certified design
This receiver is THX Ultra2™ certified, allowing you to
take advantage of new THX technologies such as ASA
(Advanced Speaker Array), which can process any 5.1
channel source for 6.1 channel (THX Surround EX) or 7.1
channel (THX Ultra2™ Cinema and THX MusicMode)
playback. These features are also available when using
the i.LINK interface.
Windows Media® Audio 9 Professional decoding
It is possible to listen to the Windows Media® Audio 9
Professional (WMA9 Pro) discrete surround format using
the on-board WMA9 Pro decoder, or through the USB
connection using a software decoder on your computer.
Seamless video conversion
With the Pioneer video converter, you can use a wide
range of cords interchangeably, giving you more
flexibility when making video connections.
Easy-to-use remote control
The remote control gives you not only complete control
over every function of this receiver, but also over the main
functions for other components in your home theater
system. Using a system of preset codes, you can
program the remote to operate a wide range of other
equipment.
Energy-saving design
This receiver is designed to use less than 0.65 W of
energy when in standby.
1
With the cooperation of AIR Studios, this receiver has
been designated AIR Studios Monitor Reference:
“i.LINK” and the i.LINK logo are trademarks of the Sony
Corporation.
Contents
Our philosophy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
01 Before you start
Checking the supplied accessories . . . . . . . . . . . . . . 8
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using the remote control . . . . . . . . . . . . . . . . . . . . . . 9
Operating range of the remote control . . . . . . . . . . . 9
Recharging the remote control . . . . . . . . . . . . . . . . 9
Setting up the remote control. . . . . . . . . . . . . . . . . . 9
Calibrating the remote control screen . . . . . . . . . . 10
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the button alert volume . . . . . . . . . . . . . . . 11
Setting the time-out setting . . . . . . . . . . . . . . . . . . 11
Resetting the remote control . . . . . . . . . . . . . . . . . 11
Locking the remote control . . . . . . . . . . . . . . . . . . 12
Restarting the remote control . . . . . . . . . . . . . . . . 12
Replacing the lithium-ion batteries . . . . . . . . . . . . 12
02 Connecting your equipment
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
When making cable connections . . . . . . . . . . . . . . . 15
Connecting your TV . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting a DVD player . . . . . . . . . . . . . . . . . . . . . 17
Connecting the multichannel analog outputs . . . . 18
Connecting a satellite/cable receiver or other
set-top box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting a VCR or DVD recorder . . . . . . . . . . . . . 20
Connecting other video sources . . . . . . . . . . . . . . . . 21
Using the component video jacks . . . . . . . . . . . . . . . 22
About the video converter . . . . . . . . . . . . . . . . . . . . . 22
Connecting digital audio sources . . . . . . . . . . . . . . . 23
Connecting analog audio sources . . . . . . . . . . . . . . 24
Connecting a component to the front panel inputs . . 25
Installing your speaker system . . . . . . . . . . . . . . . . . 26
Connecting the speakers . . . . . . . . . . . . . . . . . . . . 26
Placing the speakers . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . 28
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connecting external antennas . . . . . . . . . . . . . . . . 28
Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . 29
About the AC outlet . . . . . . . . . . . . . . . . . . . . . . . . 29
6
En
03 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Basic remote control displays . . . . . . . . . . . . . . . . 33
Remote control displays for the tuner . . . . . . . . . . 35
Remote control displays for other components . . . 36
04 Getting started
Introduction to home theater . . . . . . . . . . . . . . . . . . 39
Automatically setting up for surround sound . . . . . . 39
Other problems when using the Auto Surround
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Checking the settings on your DVD (or other)
player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Playing a source . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
05 Listening to your system
About the listening modes . . . . . . . . . . . . . . . . . . . . 43
Listening in surround sound . . . . . . . . . . . . . . . . . 43
Using the Advanced surround effects . . . . . . . . . . 45
Using the Home THX modes . . . . . . . . . . . . . . . . . 45
Listening in stereo . . . . . . . . . . . . . . . . . . . . . . . . . 46
Listening with headphones . . . . . . . . . . . . . . . . . . . . 46
Using the multichannel analog inputs . . . . . . . . . . . 47
Using the Stream Direct mode . . . . . . . . . . . . . . . . . 47
Listening with Acoustic Calibration EQ . . . . . . . . . . . 48
Selecting the input signal type . . . . . . . . . . . . . . . . . 48
Selecting USB and multichannel analog
input channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Listening to high-sampling formats . . . . . . . . . . . . . 49
Using the surround back channel . . . . . . . . . . . . . . 50
Listening with virtual surround back speakers . . . . . 51
Creating a center speaker effect . . . . . . . . . . . . . . . . 51
Using Hi-bit and Hi-sampling . . . . . . . . . . . . . . . . . . 52
Using Midnight and Loudness listening . . . . . . . . . . 52
Using the tone control . . . . . . . . . . . . . . . . . . . . . . . 52
Switching the tone control on or off . . . . . . . . . . . . 52
Adjusting the bass and treble . . . . . . . . . . . . . . . . 53
Reducing noise during playback. . . . . . . . . . . . . . . . 53
Listening to dual mono soundtracks . . . . . . . . . . . . . 53
06 Using the tuner
Finding a station . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Tuning directly to a station . . . . . . . . . . . . . . . . . . . . 55
MPX mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Memorizing station presets . . . . . . . . . . . . . . . . . . . 55
Naming station presets . . . . . . . . . . . . . . . . . . . . . 56
Listening to memorized station presets . . . . . . . . . 56
07 The Surround Setup menu
Making receiver settings from the Surround
Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Systems . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . .
Acoustic Calibration EQ . . . . . . . . . . . . . . . . . . . .
Professional Acoustic Calibration EQ . . . . . . . . . .
X-Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking your surround settings . . . . . . . . . . . . . . .
57
58
60
61
61
63
65
66
Multi-room setup . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making multi-room connections . . . . . . . . . . . . . .
Using the sub room controls . . . . . . . . . . . . . . . . .
Using the i.LINK interface . . . . . . . . . . . . . . . . . . . .
About i.LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About PQLS rate control . . . . . . . . . . . . . . . . . . . .
Creating an i.LINK network . . . . . . . . . . . . . . . . . .
Using the USB interface . . . . . . . . . . . . . . . . . . . . .
Connecting a PC for Advanced MCACC output . . . .
83
83
84
85
86
86
86
87
88
11 Advanced setup
08 Controlling other equipment
Using the remote control with other components . .
Recalling preset codes . . . . . . . . . . . . . . . . . . . . . .
Programming signals from other remote controls . .
Remote Direct function . . . . . . . . . . . . . . . . . . . . . .
Editing remote control button names . . . . . . . . . . .
Multi Operation and System Off. . . . . . . . . . . . . . . .
Programming a multi operation or a
shutdown sequence . . . . . . . . . . . . . . . . . . . . . . .
Switching components on and off using the
12 volt trigger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating other Pioneer components with this
unit’s sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
67
69
70
70
72
72
74
74
09 Using other functions
Making an audio or a video recording . . . . . . . . . . .
Monitoring your recording. . . . . . . . . . . . . . . . . . .
Reducing the level of an analog signal . . . . . . . . . .
Adjusting the delay of a soundtrack. . . . . . . . . . . . .
Watching video and audio sources independently . .
Enhancing SACD playback . . . . . . . . . . . . . . . . . . .
Using the A/D converters to give greater definition
to 2-channel sound . . . . . . . . . . . . . . . . . . . . . . . . .
Dimming the display . . . . . . . . . . . . . . . . . . . . . . . .
Switching the speaker impedance . . . . . . . . . . . . . .
Checking your system settings . . . . . . . . . . . . . . . .
Resetting the system . . . . . . . . . . . . . . . . . . . . . . . .
Default receiver settings . . . . . . . . . . . . . . . . . . . .
75
75
76
76
76
77
77
77
78
78
79
79
10 Other connections
Using speaker system B . . . . . . . . . . . . . . . . . . . . .
Switching the speaker system . . . . . . . . . . . . . . . .
Using speaker system B in another room . . . . . . .
Alternating surround speaker setups using
speaker system B (ITU-R) . . . . . . . . . . . . . . . . . . .
Bi-amping your front speakers . . . . . . . . . . . . . . . . .
Bi-wiring your speakers . . . . . . . . . . . . . . . . . . . . . .
Adding a second set of surround speakers for
Bi-Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the pre-outs . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting additional amplifiers. . . . . . . . . . . . . .
Connecting an external stereo pre-amplifier . . . . .
80
80
80
80
81
82
82
82
82
83
The Input Assign menu . . . . . . . . . . . . . . . . . . . . . .
Assigning the digital inputs. . . . . . . . . . . . . . . . . .
Assigning the component video inputs . . . . . . . . .
Assigning the i.LINK inputs. . . . . . . . . . . . . . . . . .
Assigning the video inputs . . . . . . . . . . . . . . . . . .
The Expert Setup menu . . . . . . . . . . . . . . . . . . . . . .
OSD Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .
Bass Peak Level . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic Range Control . . . . . . . . . . . . . . . . . . . .
Function Rename . . . . . . . . . . . . . . . . . . . . . . . . .
OSD Overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 Volt Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-Room Setting . . . . . . . . . . . . . . . . . . . . . . . .
THX Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .
THX Ultra2 Subwoofer Setup . . . . . . . . . . . . . . . . .
Surround Back Speaker Position. . . . . . . . . . . . . .
90
90
91
91
92
92
93
93
94
94
94
95
95
96
96
96
12 Additional information
Optimizing your speaker setup . . . . . . . . . . . . . . . . 97
Basic surround setup . . . . . . . . . . . . . . . . . . . . . . 97
THX speaker system setup . . . . . . . . . . . . . . . . . . 98
Speaker system setup for DVD-Audio/
multichannel music sources . . . . . . . . . . . . . . . . . 98
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
No sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Other audio problems . . . . . . . . . . . . . . . . . . . . . 102
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
i.LINK interface . . . . . . . . . . . . . . . . . . . . . . . . . . 106
i.LINK messages . . . . . . . . . . . . . . . . . . . . . . . . . 106
USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Surround sound formats . . . . . . . . . . . . . . . . . . . . 108
Dolby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Windows Media® Audio 9 Professional . . . . . . . 109
PCM (Pulse Code Modulation) . . . . . . . . . . . . . . 109
About THX® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Maintenance of external surfaces . . . . . . . . . . . . . 110
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
7
En
01
Before you start
Chapter 1
Before you start
Checking the supplied accessories
Please check that you've received the following supplied
accessories:
• U-shaped connectors x2 (attached to back of
receiver)
• Microphone
• These operating instructions
• Warranty card
• Remote control unit
Ventilation
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat dispersal
(at least 8 in. (20 cm) at the top). If not enough space is
provided between the unit and walls or other equipment,
heat will build up inside, interfering with performance
and/or causing malfunctions.
• Remote control unit recharger and AC adapter
Receiver
• AM loop antenna
8 inches
(20 cm)
Slot and openings in the cabinet are provided for
ventilation and to protect the equipment from
overheating. To prevent fire hazard, do not place anything
on top of the unit, make sure the openings are never
blocked or covered with items (such as newspapers,
table-cloths and curtains), and do not operate the
equipment on thick carpet or a bed.
• FM wire antenna
• Power cord
Installing the receiver
• When installing this unit, make sure to put it on a
level and stable surface.
Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives off
a magnetic field). This may interfere with the sound.
– in direct sunlight
– in damp or wet areas
8
En
Before you start
– in extremely hot or cold areas
– in places where there is vibration or other movement
– in places that are very dusty
– in places that have hot fumes or oils (such as a kitchen)
01
2 Place the remote control on the recharger,
aligning the indent on the bottom of the remote
with the tabs on the recharger.
Using the remote control
Keep the following in mind when using the remote
control:
Operating range of the remote control
• Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
• The remote has a range of about 23 feet (7 meters).
• When the remote control is recharging, you’ll see the
indicator appear in the upper right corner of the
display:
30
30
Note
23 feet (7m)
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
• Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
• If the remote hasn’t been charged for awhile, the
remote control display may remain blank for several
minutes before the touch screen appears. If it
continues to remain blank, try lifting the remote
control up from the recharger and reseating it on the
recharger. If after several tries, this does not work,
see Replacing the lithium-ion batteries on page 12.
Setting up the remote control
Recharging the remote control
When the battery indicator on the remote control display
shows that the rechargeable battery is almost depleted,
recharge the remote as shown below. To make sure the
battery doesn’t run out completely, simply leave the
remote control in the recharger when not in use.
Caution
• Do not use AC adaptors other than the one supplied.
1 Connect the AC adaptor to the recharger and
plug it into an AC outlet.
After you have calibrated the screen and set the display
clock, use the other settings to customize your remote
control.
Note
• The remote control operations in this section are
accessed from the remote setup menu. To go to the
SETUP
remote setup menu, press
from the remote
control Home menu ( ):
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVR
/ LD
SETUP
9
En
Before you start
01
There are three remote setup menu screens, which
can be navigated by using the touch panel /
(cursor left/right) soft keys:
SETUP
1/3
SETUP
2/3
CALIBRATE
CLOCK DISPLAY : AM/PM
PRESET RECALL
CLOCK SETTING
LEARNING
Setting the clock
The remote control features a clock that shows both 12
and 24 hour formats.
1 Press CLOCK DISPLAY to select either AM/PM or
24H display format.
Each press switches between the two settings. The
current display format is shown after CLOCK DISPLAY.
BEEP :
SETUP
MULTI OPERATION
TIMEOUT
DIRECT FUNCTION
KEY LABEL
2/3
CLOCK DISPLAY : AM/PM
CLOCK SETTING
BEEP :
TIMEOUT
• For more on navigating the remote control menu
screens, see Basic remote control displays on
page 33.
Calibrating the remote control screen
This will make sure the remote control responds correctly
when you touch it.
1
Press CALIBRATE.
KEY LABEL
2 Press CLOCK SETTING to set the date.
Use the + and – buttons to set the year, month and day.
SETUP
2/3
1/2
DATE
CLOCK DISPLAY : AM/PM
SETUP
1/3
CALIBRATE
PRESET RECALL
LEARNING
CLOCK SETTING
+
+
+
2003
/10
/09
TIMEOUT
-
-
-
KEY LABEL
NEXT
BEEP :
CANCEL
MULTI OPERATION
DIRECT FUNCTION
3 Press NEXT to continue and set the time.
Use the + and – buttons to set the hour and minute.
2 Press the center of each cross point to align the
touch screen with the LCD panel underneath.
This adjustment will make sure your remote control is
calibrated correctly.
2/2
TIME
+
17
PLEASE TOUCH
THE UPPER "+" MARK
"MUTE": CANCEL
When you've touched both cross points, PLEASE WAIT is
displayed and you’ll return to the remote setup menu
when calibration is finished.
10
En
ENTER
+
:
08
CANCEL
4 Press ENTER when you’re finished.
You’ll return to the remote setup menu.
Before you start
01
Setting the button alert volume
You can set the volume of the ‘beep’ you hear when you
press a button on the remote.
• Press BEEP to select a setting.
Each press selects between quiet, loud or off. The current
setting is shown on the touch screen.
SETUP
3 Press ENTER when you’re finished.
You’ll return to the remote setup menu.
Resetting the remote control
Use this feature to reset the remote control settings to
the factory defaults.
Important
2/3
• Doing this will erase any of your personalized
settings.
CLOCK DISPLAY : AM/PM
CLOCK SETTING
1
BEEP :
Press RESET TO DEFAULT.
TIMEOUT
SETUP
KEY LABEL
3/3
RESET TO DEFAULT
Setting the time-out setting
• Default setting: 60sec
To save battery life, a timer automatically switches off the
remote control off after a set amount of time if no
commands are entered. You can adjust separate timeout settings for the LCD, and the remote backlight.
1
Press TIMEOUT.
SETUP
2/3
2 Confirm by pressing YES after reading each
screen.
RESET
RESET
CLOCK DISPLAY : AM/PM
CLOCK SETTING
BEEP :
TIMEOUT
KEY LABEL
2 Use the + and – buttons to set the LCD TIMEOUT
and BACKLIGHT TIMEOUT settings.
You can adjust these from 20–120 seconds.
Do you want to reset
the REMOTE to the
DEFAULT settings ?
ALL settings you made
will be ERASED.
Is it all right?
YES
YES
NO
NO
After the screen goes blank, the Home menu appears
within a minute or so, and the remote control will be reset
to the default settings.
• The backlight timeout can’t be longer than the LCD
timeout setting.
TIMEOUT
LCD TIME OUT
-
60 sec
+
BACKLIGHT TIME OUT
ENTER
60 sec
+
CANCEL
11
En
01
Before you start
Locking the remote control
2
Remove the battery cover.
This receiver has a remote control lock feature that
makes the remote control touch screen and hard keys
inoperative.
1 At the same time, press the and hard keys
for about three seconds.
• This is not possible from the remote setup screen.
ENTER
CHANNEL
MENU
VOLUME
3 Use a pen or other sharp instrument to press the
reset button located in the hole to the right (above
the battery).
MUTE
RES
ET
SYSTEM
SETUP
RECEIVER
LOCKED! shows on the touch screen to indicate the
remote control is locked.
2 To unlock the remote control, repeat step 1.
Once the remote control is unlocked, the touch screen
shows the Home menu.
Restarting the remote control
If the remote control display freezes during operation
(none of the buttons seem to work), you may need to
restart the unit.
Important
• Doing this will not erase any of your personalized
settings or presets except for the clock setting.
1 Use a small phillips screwdriver to remove the
screw fixing the battery cover to the back of the
remote.
After restarting the remote control, the touch screen
shows the Home menu.
Replacing the lithium-ion batteries
If you notice that the remote will no longer hold a charge,
you may need to replace the lithium-ion battery cells.
Caution
• The lithium-ion batteries may present a fire or
chemical burn hazard if misused. Do not
disassemble, heat above 100˚C (212˚F), or
incinerate.
• Replacement cells must be of type AZW7264,
manufactured by NEC TOKIN Corporation. Use of any
other battery cells may result in fire or explosion.
Contact the Pioneer Customer Support division to
obtain new batteries. Replacement cells are not
covered under warranty.
• Dispose of used battery cells immediately after
replacement. Keep away from children.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public institution’s rules that apply in your country or
area.
12
En
Before you start
01
1 Use a small phillips screwdriver to remove the
screw fixing the battery cover to the back of the
remote.
2
Remove the battery cover.
3 Disconnect the old battery cell from the unit.
Do not pull the connector out by holding onto the
attached wires. Hold the connector firmly with your
fingers, or use a small screwdriver (or other sharp tool) to
disconnect it.
4 Connect the new battery cell.
Push the connector in until it is fully inserted. Make sure
you keep the wire out of the way and line up the cell
properly so that the battery cover can be closed easily.
13
En
02
Connecting your equipment
Chapter 2
Connecting your equipment
This receiver provides you with almost limitless possibilities for connecting your audio/video system, but it doesn’t
have to be difficult. Depending on your needs, you could be up and running in no time after a few simple connections.
This section has been designed so that you can read through this short introduction, then jump to the specific
connections that you need to make. For a basic home theater setup, you may only need to look through the TV, DVD
and speaker connections.
Rear panel
AC OUTLETT
Hz
00W (0.8A) MAX
R
IN
IN
OUT
DVR/
VCR1
IN
OUT
OUT
OUT
AC IN
N
L
S
SURROUND
IN
RROUND BACK & B )
R
VCR2
L
IN
IN
(Single)
SSUROUT
OUT
VCR3
IN
IN
VIDEO
Caution
• Before making or changing the connections, switch
off the power and disconnect the power cord from the
power outlet. Plugging in components should be the
last connection you make with your system.
1 USB audio input
The USB audio input allows you to use your PC as a
playback source for stereo or multichannel digital audio.
See Using the USB interface on page 87 for connection
details.
2 Digital audio outputs
Two optical digital audio outputs for connecting to a CD,
MD or other digital recorder. See Connecting a VCR or
DVD recorder on page 20 for connection details.
3 Digital audio inputs
Three optical and three coaxial digital audio inputs for
connecting digital audio sources to this receiver. There’s
also a 2 RF IN jack for connection to an LD player with
a 2 RF output.
All the inputs are freely assignable to input functions for
maximum flexibility.
14
En
18
12V TRIGGER
TRI
L
1
DC OUT 12V
TOTAL 100mA MAX
2
SPEAK
SP
• If a connected component does not correspond to
the input function (DVD/LD, etc.), see Assigning the
digital inputs on page 90 to assign it properly.
4 Stereo analog audio source inputs/outputs
Four sets of analog audio jacks for connection to audio
sources such as CD players, tape decks and turntables.
The CD-R/TAPE 1/MD and TAPE 2 MONITOR functions
also feature outputs for recording. See Connecting
analog audio sources on page 24 for connection details.
5 Multichannel analog audio inputs
7.1 channel analog inputs for connection to a DVD player
with multichannel analog outputs. See Connecting the
multichannel analog outputs on page 18 for connection
details.
6 i.LINK connectors
Two S400-type i.LINK connectors allow you to connect
this receiver to other compatible i.LINK audio devices for
high-resolution, multichannel digital audio input/output.
See Using the i.LINK interface on page 85 for connection
details.
7 Turntable ground
A grounding (earth) terminal for use with turntables that
require it. See Connecting analog audio sources on
page 24 for connection details.
Connecting your equipment
8 Pre-amplifier output/power amplifier input
When using this receiver as an integrated amplifier, leave
the pre-amp outputs connected to the power amp inputs
with the supplied U-shaped connectors. Removing these
connectors allows you to use this unit as a pre-amplifier
or power amplifier only, or to integrate another amplifier
into your setup for more inputs. See Using the pre-outs on
page 82 for connection details.
9 Multichannel pre-amplifier outputs
Multichannel pre-amp outputs that you can use to
connect separate amplifiers for center, surround,
surround back and subwoofer channels. See Using the
pre-outs on page 82 for connection details.
10 Control input/output
Mini jack terminals for connection to other Pioneer
components to enable you to control all your equipment
from a single IR remote sensor. See Operating other
Pioneer components with this unit’s sensor on page 74
for connection details.
02
17 Antenna terminals
Connections for AM and FM radio antennas. See
Connecting antennas on page 28 for connection details.
18 12V trigger jacks
These terminals output DC 12V according to the input
functions (total 100 mA max.). See Switching
components on and off using the 12 volt trigger on
page 74 for connection details.
19 Speaker terminals
These are the main speaker terminals for front, center,
surround and surround back speakers. See Installing
your speaker system on page 26 for connection details.
20 AC power outlet
This 120V AC power outlet can be used to power another
component in your setup (up to 100 W). Power to this
outlet is switched off when the receiver is in standby.
21 AC power inlet
Connect the supplied power cord here.
11 Monitor video outputs
Three video outputs consisting of a standard composite
video output and two S-video outputs, for connection to
monitors and TVs. See Connecting your TV on page 16 for
connection details.
22 B speaker terminals
Stereo B speaker terminals that you can use to connect
a second pair of speakers for use in another room, for
example. See Using speaker system B on page 80 for
connection details.
12 Multi-room and source outputs
Outputs for connection to a second amplifier in a
separate room. See Multi-room setup on page 83.
When making cable connections
13 Audio/video source inputs
Each of the seven source input functions has stereo
analog audio jacks, a composite video jack and an Svideo jack for basic connections. On top of these, you can
assign digital audio and component video jacks to input
functions as necessary. As well as audio/video inputs,
the three input functions DVR/VCR 1, VCR 2 and VCR 3
also have audio/video outputs for recording. See
Connecting a VCR or DVD recorder on page 20 for
connection details.
14 Remote input (multi-room and source)
The remote input allows you to connect an external
remote control sensor, for use in a multi-room setup, for
example. See Multi-room setup on page 83 for
connection details.
15 Component video inputs/output
The three component video inputs are freely assignable
to any of the audio/video input functions. The component
video output is for connection to a monitor or TV. See
Using the component video jacks on page 22 for
connection details.
Be careful not to arrange cables in a manner that bends
the cables over the top of this unit. If the cables are laid
on top of the unit, the magnetic field produced by the
transformers in this unit may cause a humming noise to
come from the speakers.
• When connecting optical cables, be careful when
inserting the plug not to damage the shutter
protecting the optical socket.
• When storing optical cable, coil loosely. The cable
may be damaged if bent around sharp corners.
16 RS-232C connector
This port is provided for connecting a personal computer
for graphical output when using Advanced MCACC.
15
En
02
Connecting your equipment
Connecting your TV
This page shows you how to connect your TV to the
receiver. To be able to play the sound from the TV’s builtin tuner, connect the analog audio outputs from your TV
to this receiver.
If your TV has a built-in digital decoder, you can connect
the digital audio output to this receiver to enjoy Dolby
Digital and DTS sound from digital TV broadcasts.
• Use a stereo RCA/phono jack cable for the
connection.
3 Connect a coaxial digital audio output from your
TV to the DIGITAL 2 (TV/DVD) input on this receiver.
• Use a coaxial cable designed for digital audio for the
connection.
• If your TV only has an optical digital output, you can
connect it to one of the optical inputs on this receiver
using an optical cable. When you set up the receiver
you’ll need to tell the receiver which input you
connected the TV to (see also Assigning the digital
inputs on page 90).
1 Connect the MONITOR OUT 1 video jack on this
receiver to a video input on your TV.
• You can use a standard RCA/phono jack video cable
to connect to the composite video jack, or for higher
quality video, you can use an S-video cable to
connect to the S-video jack (S2 VIDEO).
• See Using the component video jacks on page 22 if
you want to use the component video outputs to
connect this receiver to your TV.
Note
• If your TV doesn’t have a digital audio output, omit
step 3 above.
2 Connect the analog audio outputs from your TV
to the TV/DVD AUDIO inputs on this receiver.
• If you use different cord types for the TV and the
source component, overlay information doesn’t
appear.
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
OUT
DVR/
VCR1
IN
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
(Single)
OUT
REC
R
TAPE 2
MONITOR
IN
R
PLAY
FRONT
R
SUB W
R
ASSIGNABLE
SURROUND
L
R
MULTI CH INPUT
Y
PB
SURROUND
SELECTABLE (SURROUND BACK & B )
R
B
PR
VCR2
IN
IN
OUT
OUT
PR
L
ASSIGNABLE
L (Single)
1
IN
IN
L
AUDIO
RS-232C
VIDEO
L
R
R
VCR3
R
(Single)
SURROUND
BACK
(Single)
CENTER
SURROUND
BACK
L
Y
PB
L
OUT
OUT
L
IN
3
IN
2
L
SURROUND
IN
2
OUT
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
2
L
R
ANALOG AUDIO OUT
1
3
OPTICAL
COAXIAL
VIDEO
IN
DIGITAL AUDIO OUT
TV
16
En
S-VIDEO
IN
Connecting your equipment
02
Connecting a DVD player
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
ASSIGNABLE
L
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
OUT
DVR/
VCR1
IN
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
SURROUND
OUT
REC
R
R
PLAY
FRONT
L
SUB W
SURROUND
R
B
PR
IN
IN
OUT
OUT
PR
L
ASSIGNABLE
R
R
VCR3
R
MULTI CH INPUT
L
AUDIO
RS-232C
VIDEO
L
R
1
IN
IN
L (Single)
(Single)
SURROUND
BACK
(Single)
SURROUND
BACK
L
PB
CENTER
SURROUND
R
Y
SELECTABLE (SURROUND BACK & B )
VCR2
L
R
Y
PB
L
OUT
OUT
L
IN
3
IN
2
(Single)
TAPE 2
MONITOR
IN
IN
2
OUT
12V TRIGGER
S2 VIDEO
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
OPTICAL
COAXIAL
DIGITAL OUT
1
R
AUDIO L
ANALOG OUT
2
S-VIDEO
VIDEO OUT
3
DVD player
Different DVD players offer a different selection of
connections, but all should give you at least a digital
audio output, stereo analog audio outputs and a video
output. Additionally, you may have a player with
multichannel analog audio outputs and different kinds of
video outputs to choose from.
1 Connect a coaxial digital audio output on your
DVD player to the DIGITAL 1 (DVD/LD) input on this
receiver.
• Use a coaxial cable designed for digital audio for the
connection.
• If your DVD player only has an optical digital output,
you can connect it to one of the optical inputs on this
receiver using an optical cable. When you set up the
receiver you’ll need to tell the receiver which input
you connected the player to (see also Assigning the
digital inputs on page 90).
2 If your DVD player only has stereo analog audio
outputs, connect these to the DVD/LD AUDIO inputs
on this receiver.
• Use standard RCA/phono jack cables for the
connections.
• If your DVD player has multichannel analog outputs,
see Connecting the multichannel analog outputs
below for how to connect it.
3 Connect a composite or S-video output on your
DVD player to the DVD/LD VIDEO or DVD/LD S2
VIDEO input on this receiver.
• Use a standard video cable or an S-video cable for the
connection.
• If your player also has a component video output, you
can connect this too. See Using the component video
jacks on page 22 for more on this.
17
En
02
Connecting your equipment
Connecting the multichannel analog outputs
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
OUT
AC 120 V 60Hz
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
OUT
DVR/
VCR1
IN
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
(Single)
OUT
REC
TAPE 2
MONITOR
IN
PLAY
FRONT
SURROUND
L
R
L
SUB W
R
L
Y
PB
SURROUND
SELECTABLE (SURROUND BACK & B )
R
B
OUT
PR
VCR2
IN
IN
OUT
OUT
PR
L
ASSIGNABLE
CENTER
L (Single)
MULTI CH INPUT
R
VCR3
L
AUDIO
RS-232C
VIDEO
L
R
1
IN
IN
R
(Single)
SURROUND
BACK
(Single)
SURROUND
BACK
R
Y
PB
L
IN
OUT
L
R
IN
3
IN
2
OUT
2
R
SURROUND
ASSIGNABLE
AC OUTLET
FRONT
COMPONENT VIDEO
CENTER
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
R
FRONT
R
SURR.
L SUB W. CENTER
R
L
MULTI CH
OUTPUT
1
L
SURR.
BACK
MULTI CH. OUT
2
DVD player
For DVD Audio and SACD playback, your DVD player may
have 5.1, 6.1 or 7.1 channel analog outputs (depending
on whether your player supports surround back
channels).
1 Connect the front, surround, center and
subwoofer outputs on your DVD player to the
corresponding MULTI CH INPUTS on this receiver.
• Use standard RCA/phono jack cables for the
connections.
• Take care to connect each output to its
corresponding input on the receiver.
18
En
2 If your DVD player also has outputs for surround
back channels, connect these to the corresponding
MULTI CH INPUTS on this receiver.
• Use standard RCA/phono jack cables for the
connections.
• If there is a single surround back output, connect it to
the SURROUND BACK L (SINGLE) jack on this
receiver.
Note
• To listen to multichannel analog audio you’ll need to
switch the input signal selector to MULTI CH INPUT
(see Playing a source on page 41 for more on this).
See also Selecting USB and multichannel analog input
channels on page 49.
Connecting your equipment
02
Connecting a satellite/cable receiver or other set-top box
• If your set-top box only has a coaxial digital output,
you can connect it to one of the coaxial inputs on this
receiver using a coaxial digital audio cable. When
you set up the receiver you’ll need to tell the receiver
which input you connected the set-top box to (see
also Assigning the digital inputs on page 90).
Satellite and cable receivers, and terrestrial digital TV
tuners are all examples of so-called ‘set-top boxes’.
1 Connect a set of audio/video outputs on the settop box component to the SAT AUDIO and VIDEO
inputs on this receiver.
• Use a stereo RCA/phono jack audio cable for the
audio connection and a video or S-video cable for the
video connection.
Note
• If your satellite/cable receiver doesn’t have a digital
audio output, omit step 2 above.
2 Connect an optical digital audio output from
your set-top box component to the DIGITAL 4 (SAT)
input on this receiver.
• Use an optical cable for the connection.
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
ASSIGNABLE
L
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
OUT
DVR/
VCR1
IN
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
SURROUND
OUT
REC
R
R
L
SUB W
R
B
PR
L
ASSIGNABLE
OUT
R
L (Single)
MULTI CH INPUT
R
VCR3
SURROUND
BACK
R
L
RS-232C
AUDIO
VIDEO
L
R
1
IN
IN
(Single)
SURROUND
BACK
(Single)
L
L
SURROUND
CENTER
SURROUND
R
PB
PR
IN
OUT
R
Y
SELECTABLE (SURROUND BACK & B )
VCR2
IN
PLAY
FRONT
Y
PB
L
OUT
OUT
L
IN
3
IN
2
(Single)
TAPE 2
MONITOR
IN
IN
2
OUT
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
DIGITAL OUT
L
AUDIO
VIDEO
R
S-VIDEO
AV OUT
STB
19
En
02
Connecting your equipment
Connecting a VCR or DVD recorder
3 Connect an optical digital audio output from the
recorder to the DIGITAL 5 (DVR/VCR1) input on this
receiver.
• Use an optical cable for the connection.
This receiver has three sets of audio/video inputs and
outputs suitable for connecting analog or digital video
recorders, including VCRs, DVD-recorders and HDD
recorders.
• If your recorder only has a coaxial digital output, you
can connect it to one of the coaxial inputs on this
receiver using a coaxial digital audio cable. When
you set up the receiver you’ll need to tell the receiver
which input you connected the recorder to (see also
Assigning the digital inputs on page 90).
1 Connect a set of audio/video outputs on the
recorder to the DVR/VCR1 AUDIO and VIDEO inputs
on this receiver.
• Use a stereo RCA/phono jack audio cable for the
audio connection and a video or S-video cable for the
video connection.
• The digital outputs from other recorders can be
connected to any spare digital audio inputs on this
receiver. You can assign them when setting up the
receiver (see also Assigning the digital inputs on
page 90).
• For a second and third recorder, use the VCR2 IN and
VCR3 IN inputs.
2 Connect a set of audio/video inputs on the
recorder to the DVR/VCR1 AUDIO and VIDEO outputs
on this receiver.
• Use a stereo RCA/phono jack audio cable for the
audio connection and a video or S-video cable for the
video connection.
Note
• If your video component doesn’t have a digital audio
output, omit step 3 above.
• For a second and third recorder, use the VCR2 and
VCR3 outputs.
• In order to record, you must connect the analog
audio cables (the digital connection is for playback
only).
VSX-59TXi
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
IN
PHONO
OUT 2
R
AUDIO
L
IN
5
AUDIO
(DVR/
VCR1)
(SAT)
IN
3 IN
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
R
R
(DVD/
LD)
IN
TV/
DVD
IN
IN
SAT
IN
IN
L
L
SUB W.
PRE OUT
1
(Single)
OUT
REC
R
TAPE 2
MONITOR
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
AC 120 V 60Hz
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
SURROUND
L
SUB W
R
L
R
OUT
OUT
IN
3
IN
2
Y
Y
PB
PB
L
SURROUND
IN
SELECTABLE (SURROUND BACK & B )
B
PR
IN
IN
OUT
OUT
R
PR
L
ASSIGNABLE
L (Single)
MULTI CH INPUT
OPTICAL
R
1
IN
IN
L
AUDIO
RS-232C
VIDEO
12V TRIGGER
S2 VIDEO
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
1
COAXIAL
DIGITAL OUT
L
AUDIO
R
VIDEO
AV OUT
DVR, VCR, etc.
L
R
VCR3
R
(Single)
SURROUND
BACK
(Single)
CENTER
SURROUND
BACK
SURROUND
OUT
VCR2
L
R
OUT
DVR/
VCR1
IN
2
L
R
PLAY
FRONT
3
En
AC OUTLET
FRONT
PR
REC
CD-R/
TAPE1/
MD
IN
ASSIGNABLE
20
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
COMPONENT VIDEO
CENTER
OUT
PLAY
(CD)
DVD/
LD
IN
POWER
AMP
IN
IN
(CD-R/
TAPE1/
MD)
IN
4
MONITOR
OUT 2
IN
CD
OUT 1
6
MULTIROOM &
SOURCE
S-VIDEO
L
AUDIO
R
VIDEO
AV IN
S-VIDEO
2
Connecting your equipment
02
Connecting other video sources
• You may need to assign the digital input you used
when setting up the receiver (see also Assigning the
digital inputs on page 90).
You can basically use any of the audio/video inputs on
this receiver for any kind of video source. The example
illustration below shows a component connected to the
VCR2 inputs.
3 If the source component is an LD player with a
2 RF digital audio output, connect this to the 2 RF
input on this receiver.
To ensure compatibility with all laserdiscs, connect both
the PCM and 2 RF outputs from your LD player.
1 Connect the analog audio outputs and a video
output of the source component to a set of spare
audio/video inputs on this receiver.
• Use a stereo RCA/phono jack audio cable for the
audio connection and a video or S-video cable for the
video connection.
• Use a coaxial cable designed for digital audio for the
2 RF connection.
• You may need to assign the 2 RF digital input when
setting up the receiver (see also Assigning the digital
inputs on page 90).
2 If the source component has a digital audio
output, connect it to a spare digital audio input on
this receiver.
• Use a coaxial cable designed for digital audio or an
optical cable for the connection depending on the
type of input you used.
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
OUT
DVR/
VCR1
IN
OUT
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
(Single)
OUT
REC
R
TAPE 2
MONITOR
IN
SURROUND
R
SUB W
L
ASSIGNABLE
R
SURROUND
R
B
PR
PR
L
ASSIGNABLE
IN
OUT
L (Single)
MULTI CH INPUT
R
VCR3
R
L
AUDIO
RS-232C
VIDEO
L
R
1
IN
IN
(Single)
SURROUND
BACK
(Single)
OUT
L
PB
CENTER
SURROUND
BACK
R
Y
SELECTABLE (SURROUND BACK & B )
VCR2
L
R
SURROUND
Y
PB
L
OUT
OUT
L
IN
3
IN
2
IN
PLAY
FRONT
IN
2
12V TRIGGER
S2 VIDEO
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
2
3
DIGITAL OUT
1
PCM
2 RF
L
AUDIO
VIDEO
R
S-VIDEO
AV OUT
LD player, video player, TV game, etc.
21
En
02
Connecting your equipment
Using the component video jacks
2 Connect the COMPONENT VIDEO MONITOR OUT
jacks on this receiver to the component video inputs
on your TV or monitor.
• Use a three-way component video cable.
Component video should deliver superior picture quality
when compared to composite or S-video. A further
advantage (if your source and TV are both compatible) is
progressive-scan video, which delivers a very stable,
flicker-free picture. See the manuals that came with your
TV and source component to check whether they are
compatible with progressive-scan video. Note that it is
not possible to see overlay information when you have
connected using component video cables.
About the video converter
The video converter allows you to connect various video
sources using composite, S-video or component video
connections and the signal will be output through all of
the MONITOR VIDEO OUT jacks. The only exception is
component video input, which is only output from the
component video output. Therefore, if you want to
connect any source using component video, you must
also connect your TV using component video. If several
video components are connected to the same input
function, the converter gives priority to component, Svideo, then composite (in that order).
1 Connect the component video outputs of your
source to a set of component video inputs on this
receiver.
There are three component video inputs; they are all
freely assignable (COMPONENT IN 1, as a default,
should already be assigned to DVD/LD) so that they can
be used in conjunction with any of the audio/video input
functions of the receiver.
Note that in most cases, you’ll need to assign the
component video input (see Assigning the component
video inputs on page 91), or else you may see the S-video
or composite video input instead.
• You can’t see overlay information if you use different
cord types for the TV and the source component.
• Also note that this feature is available with NTSC
signals only. For a PAL signal, make sure you’ve used
the same type of cable for your video component and
monitor connections.
• Use a three-way component video cable for the
connection.
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SAT
IN
IN
OUT
R
CENTER
PB
OUT
DVR/
VCR1
IN
SWITCHED 100W (0.8A) MAX
AC IN
PR
PR
CENTER
OUT
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
(Single)
OUT
REC
TAPE 2
MONITOR
IN
R
L
R
L
SUB W
L
ASSIGNABLE
R
MULTI CH INPUT
R
B
PR
PR
L
ASSIGNABLE
IN
L (Single)
OUT
R
VCR3
L
RS-232C
AUDIO
L
R
1
IN
IN
R
(Single)
SURROUND
BACK
CENTER
SURROUND
BACK
R
SURROUND
SELECTABLE (SURROUND BACK & B )
VCR2
L
R
PB
(Single)
OUT
SURROUND
Y
OUT
OUT
IN
PLAY
FRONT
Y
PB
L
IN
2
SURROUND
IN
3
IN
2
VIDEO
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
1
Y
PB
PR
DVD player
COMPONENT
VIDEO
2
Y
PB
PR
COMPONENT
VIDEO
TV
22
En
Connecting your equipment
02
Connecting digital audio sources
This receiver has both digital inputs and outputs,
allowing you to connect digital components for playback
and for making digital recordings. Many digital
components also have analog connections for recording
analog sources (such as a turntable or tape deck). See
Connecting analog audio sources below for more on this.
2 Connect one of the DIGITAL outputs on this
receiver to a digital input on the component.
• Use an optical cable to connect to the DIGITAL
OUT1 or OUT2 (OUT1 is shown in the illustration
below).
1 Connect an optical digital audio output on your
digital component to the DIGITAL 6 (CD-R/TAPE1/
MD) input on this receiver.
• Use an optical cable for the connection.
Note
• In order to record some digital sources, you must
make analog connections as explained in Connecting
analog audio sources below.
• If your digital component only has a coaxial digital
output, you can connect it to one of the coaxial inputs
on this receiver using a coaxial cable. When you set
up the receiver you’ll need to tell the receiver which
input you connected the component to (see also
Assigning the digital inputs on page 90).
• This unit has an on-board WMA9 Pro decoder, so it is
possible to playback WMA9 Pro-encoded audio using
a coaxial or optical digital connection when
connected to a WMA9 Pro-compatible player.
However, the connected PC, DVD player, set-top box,
etc. must be able to output WMA9 Pro format audio
signals through a coaxial or optical digital output.
• The digital outputs from other components can be
connected to any spare digital audio inputs on this
receiver. You can assign them when setting up the
receiver (see also Assigning the digital inputs on
page 90).
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
IN
PHONO
OUT 2
R
AUDIO
L
6
IN
5
AUDIO
IN
4
(SAT)
IN
3 IN
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
R
R
L
(DVD/
LD)
IN
TV/
DVD
IN
IN
SAT
IN
IN
L
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
(CD)
DVD/
LD
IN
POWER
AMP
IN
IN
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
MONITOR
OUT 2
IN
CD
OUT 1
MULTIROOM &
SOURCE
(Single)
OUT
REC
R
TAPE 2
MONITOR
IN
R
PLAY
FRONT
SUB W
SURROUND
L
R
L
R
OUT
OUT
L
IN
3
IN
2
Y
Y
PB
PB
PR
PR
L
SURROUND
IN
SELECTABLE (SURROUND BACK & B )
IN
IN
OUT
OUT
R
B
VCR2
L
ASSIGNABLE
L (Single)
MULTI CH INPUT
R
VCR3
L
AUDIO
RS-232C
VIDEO
L
R
1
IN
IN
R
(Single)
SURROUND
BACK
(Single)
CENTER
SURROUND
BACK
SURROUND
ASSIGNABLE
OUT
2
L
R
OUT
DVR/
VCR1
IN
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
1
OPTICAL
COAXIAL
DIGITAL OUT
OPTICAL
2
DIGITAL IN
CD-R, MD, DAT, etc.
23
En
02
Connecting your equipment
Connecting analog audio sources
• Use a stereo RCA/phono jack audio cable for the
connections.
This receiver features four stereo audio-only inputs. Two
of these inputs have corresponding outputs for use with
audio recorders.
• If your cassette deck has a monitoring function,
connect it to the TAPE 2 MONITOR jacks on the rear
panel. See Monitoring your recording on page 75 for
more on this.
One of the audio inputs (PHONO) is a dedicated
turntable input which should not be used for any other
type of component. This input also has a grounding
terminal that most turntables require.
2 Turntables only: Connect the stereo audio outputs
to the PHONO inputs on this receiver.
• If your turntable has a grounding wire, secure it to the
ground terminal on this receiver.
1 Connect the analog audio outputs of the source
component to a set of spare audio inputs on this
receiver.
• If you’re connecting a tape deck, MD recorder, etc.,
connect the analog audio outputs (REC) to the analog
audio inputs on the recorder.
• If your turntable has line-level outputs (no grounding
wire), connect them to the CD inputs instead.
1
Turntable
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
AUDIO
R
L
IN
AUDIO
CD
OUT 1
6
(CD-R/
TAPE1/
MD)
IN
5
R
R
L
IN
4
(SAT)
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
OUT
DVR/
VCR1
IN
SUB W.
PRE OUT
1
PLAY
2 IN
AC 120 V 60Hz
AC IN
PR
PR
REC
CD-R/
TAPE1/
MD
IN
IN
(CD)
L
AC OUTLET
FRONT
COMPONENT VIDEO
CENTER
OUT
(DVR/
VCR1)
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
(Single)
OUT
REC
R
TAPE 2
MONITOR
IN
R
PLAY
FRONT
SUB W
SURROUND
L
L
ASSIGNABLE
R
MULTI CH INPUT
Y
PB
SURROUND
SELECTABLE (SURROUND BACK & B )
R
B
PR
VCR2
IN
IN
OUT
OUT
PR
L
ASSIGNABLE
L (Single)
R
VCR3
R
L
AUDIO
RS-232C
VIDEO
L
R
1
IN
IN
(Single)
SURROUND
BACK
(Single)
CENTER
SURROUND
BACK
R
Y
PB
L
OUT
OUT
L
IN
3
IN
2
L
R
SURROUND
IN
2
OUT
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
OUT
PLAY
2
IN
REC
R
AUDIO IN/OUT
24
En
L
Tape deck, etc.
Connecting your equipment
02
Connecting a component to the front panel inputs
video games and portable audio/video equipment.
The front panel inputs include a composite video jack
(VIDEO), an S-video jack (S-VIDEO), stereo analog audio
inputs (AUDIO L/R) and an optical digital audio input
(DIGITAL). You can use these connections for any kind of
audio/video component, but they are especially
convenient for portable equipment such as camcorders,
ACOUSTIC
CAL.
TONE
OPTION
DIGITAL NR
CLASS
• The illustration below shows example connections to
a portable DVD player.
SB CH
MODE
TUNER
MIDNIGHT
• Pull down the front cover where indicated to access
the front panel inputs.
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
VSX-59TXi
COLOR
VIDEO IN/OUT
AUDIO IN/OUT
BRIGHT
MONITOR
PHONES
ON/OFF
HOLD
DIGITAL OUT (OPTICAL)
Portable DVD player, etc.
25
En
02
Connecting your equipment
Installing your speaker system
main surround speakers should always be connected as
a pair, but you can connect just one surround back
speaker if you like (it must be connected to the left
surround back terminal). You can use speakers with a
nominal impedance between 4–16Ω (please see
Switching the speaker impedance on page 78 if you plan
to use speakers with an impedance of less than 6Ω).
To take full advantage of the receiver’s surround sound
capabilities connect front, center, surround and
surround back speakers, as well as a subwoofer.
Although this is ideal, other configurations with fewer
speakers—no subwoofer or no center speaker, or even
no surround speakers—will work. At the very least, front
left and right speakers only are necessary. Note that your
Front
right
Front
left
Subwoofer
Center
LINE LEVEL
INPUT
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
IN
PHONO
OUT 2
R
AUDIO
L
6
IN
5
AUDIO
IN
4
(SAT)
IN
3 IN
2 IN
R
R
L
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
IN
TV/
DVD
IN
IN
SAT
IN
IN
L
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
(CD)
DVD/
LD
IN
POWER
AMP
IN
IN
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
MONITOR
OUT 2
IN
CD
OUT 1
MULTIROOM &
SOURCE
(Single)
OUT
REC
TAPE 2
MONITOR
IN
OUT
DVR/
VCR1
IN
OUT
OUT
OUT
SURROUND
R
L
R
L
SUB W
R
R
R
PB
PR
PR
R
B
L
ASSIGNABLE
IN
L (Single)
OUT
R
1
IN
IN
L
RS-232C
AUDIO
L
R
VCR3
R
(Single)
SURROUND
BACK
CENTER
SURROUND
BACK
L
MULTI CH INPUT
PB
L
SURROUND
(Single)
L
SURROUND
Y
SELECTABLE (SURROUND BACK & B )
VCR2
OUT
ASSIGNABLE
IN
3
Y
IN
2
IN
PLAY
FRONT
IN
2
VIDEO
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
Surround
left
Surround
back left
Connecting the speakers
Each speaker connection on the receiver comprises a
positive (+) red, and negative (–) white terminal. For
proper sound you should take care to match these up
with the terminals on the speakers themselves.
26
En
Surround
back right
Surround
right
Connecting your equipment
Caution
• Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker terminal.
If any of the bare speaker wire touches the back panel
it may cause the power to cut off as a safety measure.
Bare wire connections
Before you start connecting the speakers, make sure that
the speaker cable you’re going to use is properly
prepared with about 0.4 in. of insulator stripped from
each wire, and the exposed wire strands twisted together.
To connect a terminal, unscrew the terminal a few turns
until there is enough space to insert the exposed wire.
Once the wire is in position, tighten the terminal until the
wire is firmly clamped.
02
• Other connections on page 80 provides greater detail
on alternate speaker setups such as using speaker
system B (page 80), bi-surround (page 80), bi-amping
(page 81) and bi-wiring (page 82).
Placing the speakers
Where you put your speakers in the room has a big effect
on the quality of the sound. The following guidelines
should help you to get the best sound from your system.
(see also Optimizing your speaker setup on page 97).
• The subwoofer can be placed on the floor. Ideally, the
other speakers should be at about ear-level when
you’re listening to them. Putting the speakers on the
floor (except the subwoofer), or mounting them very
high on a wall is not recommended.
• For the best stereo effect, place the front speakers
6–9 ft. apart, at equal distance from the TV.
• Install the center speaker above or below the TV so
that the sound of the center channel is localized at
the TV screen.
• When placing speakers near the TV, use magnetically
shielded speakers to prevent possible interference,
such as discoloration of the picture when the TV is
switched on. If you do not have magnetically shielded
speakers and notice discoloration of the TV picture,
move the speakers farther away from the TV.
• If possible, install the surround speakers slightly
above ear level.
Banana plug connections
If you want to use speaker cables terminated with banana
plugs, screw the speaker terminal fully shut then plug the
banana plug into the end of the speaker terminal.
Front L
Front R
Subwoofer
Center
Surround
R
Surround
L
Surround
back L
Note
• Please refer to the manual that came with your
speakers for details on how to connect the other end
of the speaker cables to your speakers.
• The speaker terminals on this receiver can be
connected in a number of ways, depending on your
setup. See Speaker Systems on page 58 for an
overview of the possible configurations.
Surround
back R
Caution
• Make sure that all speakers are securely installed.
This not only improves sound quality, but also
reduces the risk of damage or injury resulting from
speakers being knocked over or falling in the event of
external shocks such as earthquakes.
27
En
Connecting your equipment
02
Connecting antennas
The supplied antennas provide a simple way to listen to
AM and FM radio. If you find that reception quality is
poor, an outdoor antenna should give you better sound
quality—see Connecting external antennas below.
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
AC 120 V 60Hz
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
(Single)
OUT
REC
TAPE 2
MONITOR
IN
PLAY
FRONT
R
R
SURROUND
L
R
L
SUB W
MULTI CH INPUT
OUT
OUT
IN
3
IN
2
Y
Y
PB
PB
L
SURROUND
IN
SELECTABLE (SURROUND BACK & B )
IN
IN
OUT
OUT
R
B
PR
VCR2
PR
L
ASSIGNABLE
L (Single)
R
1
IN
IN
L
AUDIO
L
R
VCR3
R
(Single)
SURROUND
BACK
CENTER
SURROUND
BACK
R
OUT
(Single)
L
L
OUT
DVR/
VCR1
IN
2
R
SURROUND
ASSIGNABLE
AC OUTLET
FRONT
COMPONENT VIDEO
DVD/
LD
IN
CENTER
OUT
PLAY
3 IN
POWER
AMP
IN
IN
MONITOR
OUT 2
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
RS-232C
VIDEO
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
VSX-59TXi
AM loop antenna
1
Note
Assemble the stand as shown in the illustration.
fig. A
fig. B
fig. C
• The signal ground () is designed to reduce noise
that occurs when an antenna is connected. It is not
an electrical safety ground.
FM wire antenna
• Bend the stand in the direction indicated (fig. A).
• Clip the loop into the stand (fig. B).
• It’s possible to fix the AM antenna to a wall (fig. C).
Before fixing, make sure that the reception is
satisfactory.
2 Pull off the protective shields of both AM
antenna wires.
• Connect the FM wire antenna to the FM UNBAL
75Ω in the same way as the AM antenna.
For best results, extend the FM antenna fully and fix to a
wall or door frame. Don’t drape loosely or leave coiled up.
Connecting external antennas
To improve FM reception connect an external FM
antenna to the FM UNBAL 75Ω.
3 Press the AM LOOP antenna terminal tabs to
open and insert one wire into each terminal.
4
Release the tabs to secure the AM antenna wires.
75Ω coaxial cable
5 Place the AM antenna on a flat surface and point
in the direction giving the best reception.
Avoid placing near computers, television sets or other
electrical appliances and do not let it come into contact
with metal objects.
28
En
ANTENNA
AM LOOP
ANTENNA
FM
75Ω UNBAL
Connecting your equipment
02
To improve AM reception, connect a 16–19 ft. length of
vinyl-coated wire to the AM LOOP terminals without
disconnecting the supplied AM loop antenna.
For the best possible reception, suspend horizontally
outdoors.
Outdoor antenna
Indoor antenna
(vinyl-coated wire)
ANTENNA
15–18 ft.
AM LOOP
ANTENNA
FM
75Ω UNBAL
Plugging in the receiver
Only plug in after you have connected all your
components, including the speakers.
Caution
• Handle the power cord by the plug part. Do not pull
out the plug by tugging the cord, and never touch the
power cord when your hands are wet, as this could
cause a short circuit or electric shock. Do not place
the unit, a piece of furniture, or other object on the
power cord or pinch the cord in any other way. Never
make a knot in the cord or tie it with other cables. The
power cords should be routed so that they are not
likely to be stepped on. A damaged power cord can
cause a fire or give you an electric shock. Check the
power cord once in a while. If you find it damaged,
ask your nearest Pioneer authorized service center or
your dealer for a replacement.
1 Plug the supplied power cord into the AC IN
socket on the back of the receiver.
2
Plug the other end into a power outlet.
About the AC outlet
Power supplied through this outlet is turned on and off by
the receiver's power switch. Total electrical power
consumption of connected equipment should not exceed
100 W (0.8 A).
Caution
• Do not connect a monitor, TV set, heater, or similar
appliance to this unit's AC outlet.
• Do not connect appliances with high power
consumption to the AC outlet in order to avoid
overheating and fire risk. This can also cause the
receiver to malfunction.
29
En
03
Controls and displays
Chapter 3
Controls and displays
Front panel
1
2 3
4
5
6 7
8
9
10 11
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-59TXi
LISTENING MODE SELECTOR
TURN/PUSH
STANDBY/ON
STANDBY
VIDEO
OFF
DVD/LD
ON
TV/DVD
SAT
VIDEO
AUDIO
DVR/VCR1
VCR2
VCR3
CD
CD-R/
TAPE1/MD
TUNER
PHONO
MULTI CH
INPUT
INPUT SELECTOR
12
13
MASTER VOLUME
14
ACOUSTIC
CAL.
16
15
17
19
18
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
20
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
21
22
23
24
25
26
1 INPUT SELECTOR dial (page 41)
Turn to select a source component. The input indicators
show the current component.
2 STANDBY/ON and power OFF / ON Press STANDBY/ON to switch the receiver on or into
standby. The OFF / ON switch turns of the main
power (you can’t switch on using the remote when it is in
the OFF position).
3 STANDBY indicator
Lights when the receiver is in standby.
4 Remote sensor
Receives the signals from the remote control.
30
En
27
VIDEO
AUDIO
28
5 Display
See Remote control on page 33.
6 MCACC indicator (page 48)
Lights when Acoustic Calibration EQ is on. Acoustic Cal
EQ is automatically set after the Auto Surround Setup
has been completed.
7 i.LINK indicator (page 85)
Lights when an i.LINK-Audio-equipped component is
selected.
8 MULTI ROOM indicator (page 83)
Shows whether the multi-room function is active or not.
Controls and displays
9 Input indicators
Shows the currently selected source component. The
MULTI CH INPUT indicator lights when a component
connected to the MULTI CH INPUT is selected. Nothing
lights if an unassigned i.LINK-equipped component or
USB connection is selected.
10 LISTENING MODE SELECTOR dial (page 43)
Turn and push to select a listening mode.
11 MASTER VOLUME dial
Adjusts the volume.
12 Front panel controls
To access the front panel controls, push gently on the
lower third portion of the panel with your finger.
03
22 SP SYSTEM A/B (page 82)
Press repeatedly to select speaker system A,B, A/B or off
(in that order). (See Using speaker system B on page 80
for exceptions to this).
23 SIGNAL SELECT (page 48)
Press to select the type of input signal for the current
source (DVD, DVR/VCR, etc.), and also to select the
number of input channels for the USB and analog
multichannel inputs.
24 VIDEO SELECT (page 76)
Press repeatedly to select the video source.
25 TAPE 2 MONITOR (page 75)
Press to monitor recordings on the device connected to
the TAPE 2 MONITOR inputs/outputs as they are being
made.
26 STREAM DIRECT (page 47)
Press to switch on/off Stream Direct.
27 SETUP MIC jack
Use to connect the supplied microphone.
28 VIDEO INPUT jacks (page 25)
• DIGITAL IN – Connect a game console, portable DVD
player, video camera (etc.), that has an optical digital
connection.
13 ACOUSTIC CAL. (page 48)
Press to switch Acoustic Calibration EQ on or off.
• S-VIDEO – Connect a video camera (etc.), that has an
S-video out.
14 MIDNIGHT (page 52)
Press to switch MIDNIGHT mode on/off.
• VIDEO / AUDIO (L/R) – Connect a video camera, etc.
that has standard RCA video/audio outputs.
15 TONE
Press to switch between TONE ON and TONE BYPASS,
which bypasses the tone controls.
16 OPTION (–/+)
Press OPTION repeatedly to select an option menu item,
then use –/+ to adjust the settings.
17 DIGITAL NR (page 53)
Press to switch DIGITAL NR on/off.
18 TUNER controls (page 55)
Use the front panel tuner controls for recalling station
presets.
19 SB CH MODE (page 50)
Use to select the surround/virtual back channel mode.
20 MULTI ROOM & SOURCE controls
If you’ve made multi-room connections (see Multi-room
setup on page 83) use these controls to control the sub
room from the main room (see Using the sub room
controls on page 84).
21 PHONES jack (page 46)
Use to connect headphones (no sound will be heard
through the speakers).
31
En
Controls and displays
03
Display
1
2
3 4
SIGNAL
L
C
R
AUTO
LS
S
RS
RF
DIGITAL
5
6
DIGITAL
LFE
OVER ATT
SP AB
DISC MTRX
ANALOG
TAPE 2
TUNED STEREO MONO
RDS
PRO LOGIC
Neo :6
E ON RF ATT
9
2ch PLAYBACK
87
1 SIGNAL indicators (page 75)
Light to indicate the currently selected input signal.
AUTO lights when the receiver is set to select the input
signal automatically.
•
2 Program format indicators
These change according to which channels are active in
Dolby, DTS, DVD-A and SACD sources.
LS, S and RS will light at the same time to indicate
6.1channel sources.
• L – Left front channel
• C – Center channel
•
PRO LOGIC
– Lights during Dolby Pro Logic II and
Pro Logic IIx processing.
•
Neo :6 – Lights during Neo:6 processing with 2channel sources.
• 2ch PLAYBACK – Lights during two-channel
playback.
7 Speaker indicators
Light to indicate the current speaker system, A and/or B.
8 TAPE 2 (page 75)
Lights when the TAPE 2 monitor is switched on.
• LS – Left surround channel
9
• RS – Right surround channel
• LFE – Low frequency effects channel
Tuner indicators
STEREO (page 55)
Lights when listening to a stereo FM broadcast in
auto/stereo mode.
3 ((( )))
Lights when an LFE signal is being input.
TUNED
Lights when tuned to a broadcast.
4
MONO (page 55)
Lights when the tuner MPX mode is set to mono.
Analog level indicators
OVER indicator
Lights when an analog input signal is too high,
risking distortion. Use the input attenuator to reduce
the level.
ATT indicator (page 76)
Lights when the input attenuator is on.
5
Character display
6
•
Digital format indicators
DIGITAL – Lights when a Dolby Digital signal is
detected.
•
– Lights when a DTS signal is detected.
•
– Lights when one of the Home THX modes is
selected.
•
– Lights during Surround EX matrix processing.
•
– Lights when a decoding DTS-ES audio.
•
En
– Lights during DTS-ES matrix processing.
• R – Right front channel
• S – Surround channel (mono)
32
MTRX
DISC
– Lights during DTS-ES discrete processing.
Controls and displays
03
Remote control
9 Contrast control
Use to adjust the contrast of the LCD touch screen.
10 VOLUME +/–
Use to adjust the volume.
6
07/24
PM 3: 55
HOME
RECEIVER
RECEIVER
INPUT 1
2
11 MUTE
Press to mute all output. Press again (or adjust the
volume using the MASTER VOLUME control) to restore
the sound.
7
8
1/3
2
3
DVR
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
9
– +
CONTRAST
1
12 Servicing terminal
For use by Pioneer service technicians.
Basic remote control displays
The remote control LCD touch screen has a number of
displays from which you can control receiver functions,
as well as control operations for other components. The
basic menu screens are explained here.
SETUP
3
Home menu screens
4
ENTER
CHANNEL
MENU
5
VOLUME
10
There are three Home menu screens, which can be
navigated by using the touch panel / (cursor left/
right) soft keys or INPUT 1, 2 or 3.
MUTE
11
SYSTEM
SETUP
RECEIVER
1/3
HOME
12
1
RECEIVER
INPUT 1
1 Date and time display
See Setting the clock on page 10 to set this to the current
time.
2 LCD touch screen
The LCD touch screen appears when the screen is
touched or a button on the remote control is pressed.
3 Cursor hard keys and ENTER
Use to navigate menus and select options/execute
commands.
4 CHANNEL +/–
Use to select channels.
5 MENU / SYSTEM SETUP
Use to display the System Setup menu (or a menu when
controlling other components, such as a DVD or TV).
6
Displays the rechargeable battery status. The recharge
indicator ( ) shows when the remote is being
recharged.
2
3
4
5
2
3
DVD
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
7
8
SETUP
2/3
HOME
RECEIVER
1
6
RECEIVER
INPUT 2
VCR2
VCR3
VIDEO
MULTI CH
INPUT
TV
CONT
MULTI
OPERATION
SETUP
3
3/3
HOME
RECEIVER
RECEIVER
1
RECEIVER
2
INPUT 3
CD-R
/ TAPE1
i.LINK
USB
PHONO
SYSTEM
OFF
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
SETUP
1 RECEIVER
Press to switch the receiver on or into standby.
7
Press to switch the touch screen backlight on or off.
8 Menu screen number
Displays the screen number in the current menu, as well
as the number of screens.
33
En
03
Controls and displays
2 INPUT 1 / 2 / 3
Press 1, 2 or 3 to find the screen with the input source
you want. After pressing the appropriate button to
choose a source, you are taken to the corresponding
function menu (see Operating menus for additional
components below).
3
Press to return to the main Home menu (see Home menu
screens above).
3 TV CONT
Press to access the TV control menu (see TV control menu
screens below).
5 STREAM DIRECT (page 47)
Press to select a Stream Direct mode.
4 SETUP
Press to access the remote control setup menu (see
Setting up the remote control on page 9).
5 / (soft keys)
Press to go to the previous/next Home menu screen.
4 / (soft keys)
Press to go to the previous/next receiver menu screen.
6 ACOUSTIC CAL. (page 48)
Press to select an acoustic calibration EQ setting.
7
Press to go to the previous screen (or set of screens).
7 SYSTEM OFF (page 72)
Press to switch off all Pioneer components in your
system, or any other component you have also
programmed to switch off using the System Off function.
RECEIVER
TV
CONT
12
8
MIDNIGHT
DIGITAL NR
13
9
10
TONE
LOUDNESS
14
11
8 MULTI OPERATION (page 72)
Use this button to perform multi operations.
2/4
RECEIVER
6 RECEIVER
Press to go to the receiver main menu (see Receiver
menu screens below).
–
OPTION
+
–
CH LEVEL
+
Receiver menu screens
There are four receiver menu screens, which can be
navigated by using the touch panel / (cursor left/
right) soft keys.
8 MIDNIGHT (page 52)
Press to switch on/off Midnight listening.
9 TONE (page 52)
Press to switch the tone controls on/off.
RECEIVER
RECEIVER
1/4
STREAM
DIRECT
5
6
1
SIGNAL
SELECT
ACOUSTIC
CAL.
2
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
3
4
11 CH LEVEL (+/–) (page 60)
Press CH LEVEL repeatedly to select a channel, then use
–/+ to adjust the level.
7
1 SIGNAL SELECT (page 48)
Press to select the type of input signal for the current
source (DVD, DVR/VCR, etc.), and also to select the
number of input channels for the USB and analog
multichannel inputs.
2 LISTENING MODE selector (page 43)
Use to select a listening mode.
34
En
10 OPTION (–/+)
Press OPTION repeatedly to select an option menu item,
then use –/+ to adjust the settings.
12 TV CONT
Press to access the TV control menu (see TV control menu
screens below).
13 DIGITAL NR
Press to switch digital noise reduction on/off (see
Reducing noise during playback on page 53).
14 LOUDNESS (page 52)
Press to switch Loudness on/off.
Controls and displays
03
3/4
RECEIVER
TV
CONT
RECEIVER
15
INPUT
SB CH
MODE
19
16
SPEAKER
A/B
INPUT
ATT
20
17
VIDEO
SELECT
DISPLAY
DIMMER
21
18
TAPE2
MONITOR
STATUS
22
23 Sub Room Control (page 84)
Use this menu screen to control your sub room setup (if
you’ve made multi-room connections). The source and
INPUT buttons select input sources, and VOLUME (+/–)
controls the sub room volume. Press MR&S ON/OFF to
use the buttons on this screen in the sub room.
Remote control displays for the tuner
The functions on these screens are used to control the
tuner (see also Using the tuner on page 54).
TUNER
15 INPUT (page 41)
Press repeatedly to cycle through all possible input
sources.
1
16 SPEAKER A/B (page 82)
Press repeatedly to select speaker system A,B, A/B or off
(in that order). (See Using speaker system B on page 80
for exceptions to this).
3
4
17 VIDEO SELECT (page 76)
Press repeatedly to select the video source.
18 TAPE 2 MONITOR (page 75)
Press to monitor recordings on the device connected to
the TAPE 2 MONITOR inputs/outputs as they are being
made.
19 SB CH MODE (page 50)
Use to select the surround/virtual back channel mode.
20 INPUT ATT (page 76)
Press to switch the input attenuator on/off.
21 DISPLAY DIMMER (page 77)
Use to adjust the brightness of the front panel display.
22 STATUS (page 78)
Press to check selected receiver settings.
RECEIVER
23
4/4
- Sub Room Control – VOLUME +
MR&S
ON/OFF
DVD
/LD
DVR
/VCR1
TUNER
TV
SAT
CD
CD-R
/TAPE1
INPUT
2
5
6
7
1/2
TV
CONT
–
STATION
+
–
TUNING
+
BAND
CLASS
MPX
DISP MODE TUNER EDIT
8
9
10
1 STATION + / – (page 55)
Press to select station presets.
2 TUNING + / – (page 54)
Use to select a listening mode.
3 CLASS (page 55)
Press to switch between the three banks (classes) of
station presets.
4 BAND (page 54)
Press to switch between AM and FM radio bands.
5 DISP MODE (page 56)
Press to switch between the frequency display and the
station name display.
6
Press to return to the main Home menu (see Home menu
screens above).
7 / (soft keys)
Press to go to the previous/next receiver menu screen.
8 MPX (page 55)
Press to listen to a radio broadcast in mono.
9 TUNER EDIT (page 55)
Press to memorize and name a station preset.
10
Press to go to the receiver main menu (see Receiver
menu screens above).
35
En
03
Controls and displays
3 INPUT
Use to select the audio/video input source.
TUNER
4
Press to return to the main Home menu (see Home menu
screens above).
2/2
TV
CONT
11
1
2
3
4
5
6
8
9
7
5 / (soft keys)
Press to go to the previous/next TV control menu screen.
6 SCREEN SIZE
Use to select the screen size on your TV.
0
7 CLR
Press to clear an entry.
DIRECT
ACCESS
12
8
CH ENTER
Use to enter channel selections directly.
CH RETURN
Press to return to the channel last selected.
11 Number buttons (page 56)
Use to input a radio frequency.
12 DIRECT ACCESS (page 55)
After pressing, you can access a radio station directly
using the number buttons.
9
Press to go to the previous screen (or set of screens).
2/4
TV CONTROL
Remote control displays for other
components
TV
The functions on these screens are available once you’ve
programmed the remote to control the appropriate
component (for example, your TV or DVD player). See
Using the remote control with other components on
page 67 for more on this. These screens work in tandem
with the remote control hard keys (see Remote control
above).
10
11
MPX
DISPLAY
SPLIT
SELECT
P in P
SWAP
IN 1
IN 2
IN 3
IN 4
TV control menu screens
1
2
3
4
5
SCREEN
SIZE
TV
DISPLAY
Press to change the display.
2
3
CLR
4
5
6
•
SPLIT
Press to split the screen.
7
8
9
0
SELECT
Press to select items on-screen.
INPUT
CH
ENTER
2 Number buttons
Use to select a channel directly.
En
6
1
1 TV
Press to switch TV power on/off.
36
10 MPX
Press to mute/restore the sound.
1/4
TV CONTROL
CH
RETURN
7
8
9
P in P
Use for picture-in-picture.
SWAP
Press to swap small and large pictures with P in P.
Controls and displays
03
11 IN1 / IN2 / IN3 / IN4
These are unassigned buttons which can be used to
learn new commands. See Programming signals from
other remote controls on page 69 for more on this.
TV
12
13
DTV
ON/OFF
DTV
MENU
DTV
GUIDE
DTV
INFO
DTV
AUDIO
VIEW
MODE
16 AV selection
Press to select the programmed picture quality mode.
17 BLU / GRN / RED / YEL
Use to make selections from a DTV menu.
3/4
TV CONTROL
15 ANT / DTV / i.LINK
Use to select the type of antenna, DTV, or i.LINK
component you’ve connected to your TV.
18 SLEEP
Press to set the TV sleep timer.
19 FREEZE
Press to freeze the picture when using a plasma display.
CC
RETURN
14
Operating menus for additional components
The example below shows the DVD menu screen.
DVD
12 DTV controls
1
DTV ON/OFF
Press to switch the digital TV on/off.
3
DTV GUIDE
Press to access the digital TV guide.
13 DTV AUDIO
Press to switch between DTV audio options.
VIEW MODE
Press to switch between view modes available.
2
17
18
AV
selection
BLU
GRN
SLEEP
TOP MENU
7
Playback buttons
4/4
(backward/forward skip)
Press to jump back to the beginning of the
current chapter or track, then to previous chapters.
Press to jump to the next chapter or track.
i.LINK
(stop)
Press to stop the disc (you can resume playback by
pressing (play)).
FREEZE
RED
DISPLAY
(play)
Press to start or resume playback.
TV
16
SUBTITLE
(backward/forward scan)
Press and hold for fast backward/forward scanning
14 RETURN
Press to return to the DTV main menu.
DTV
AUDIO
6
1 DVD
Press to switch DVD power on/off.
CC
Press to switch close-captioning on/off.
ANT
TV
CONT
4
5
DTV INFO
Press to display the DTV information screen.
15
DVD
2
DTV MENU
Press to display the DTV menu.
TV CONTROL
1/2
19
(pause)
Press to pause playback. Press again to restart.
YEL
3
AUDIO
Press to select the audio channel or language.
SUBTITLE
Press to select a subtitle display.
37
En
03
Controls and displays
DISPLAY
Press to display/change disc information shown onscreen.
TOP MENU
Press to display the top menu of a DVD disc.
4
Press to return to the main Home menu (see Home menu
screens above).
5 / (soft keys)
Press to go to the previous/next TV control menu screen.
6 TV CONT
Press to access the TV control menu (see TV control menu
screens above).
7
Press to go to the receiver main menu (see Receiver
menu screens above).
DVD
2/2
TV
CONT
DVD
8
9
1
2
3
CLR
4
5
6
+10
7
8
9
0
SEARCH
MODE
RETURN
10
11
8 Number buttons
Use to directly access tracks, chapters and titles.
9 SEARCH MODE
Use to access the search mode (to jump to a particular
part of the disc).
10 CLR
Press to clear an entry.
11 RETURN
Press to return to a previous menu screen.
38
En
Getting started
04
Chapter 4
Getting started
Introduction to home theater
You are probably used to using stereo equipment to listen
to music, but may not be used to home theater systems
that give you many more options (such as surround
sound) when listening to soundtracks.
Home theater refers to the use of multiple audio tracks to
create a surround sound effect, making you feel like
you're in the middle of the action or concert. The
surround sound you get from a home theater system
depends not only on the speakers you have set up in your
room, but also on the source and the sound settings of
the receiver.
DVD-Video has become the basic source material for
home theater due to its size, quality, and ease of use. The
true multichannel audio possible using DVD is what
creates a convincing surround sound effect and gives
you the feeling of ‘being there’.
Follow the steps in Automatically setting up for surround
sound below to achieve the best possible surround
sound by calibrating this receiver to your listening area.
1 Switch on the receiver and your TV.
If headphones are connected to the receiver, disconnect
them.
2 Connect the microphone to the SETUP MIC jack
on the front panel.
Make sure there are no obstacles between the speakers
and the microphone.
ACOUSTIC
CAL.
TONE
OPTION
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
If you have a tripod, use it to place the microphone so that
it’s about ear level at your normal listening position.
Otherwise, place the microphone at ear level using a
table or a chair.
3 Using the remote control, press RECEIVER on the
touch screen, then press the SYSTEM SETUP button.
Automatically setting up for
surround sound
1/3
HOME
RECEIVER
The Auto Surround Setup measures the acoustic
characteristics of your listening area, taking into account
ambient noise, speaker size and distance, and tests for
both channel delay and channel level. After you have set
up the microphone provided with your system, the
receiver uses the information from a series of test tones
to optimize the speaker settings and equalization for your
particular room.
Make sure you do this before moving on to Playing a
source on page 41.
SB CH
MODE
TUNER
MIDNIGHT
SP SYSTEM
A/B
VIDEO INPUT
PHONES
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
SETUP
ENTER
CHANNEL
MENU
VOLUME
MUTE
SYSTEM
SETUP
Important
• Make sure the microphone and speakers are not
moved during the Auto Surround Setup.
• Using the Auto Surround Setup will overwrite any
existing speaker settings in the receiver.
• After three minutes of inactivity during the Auto
Surround Setup, the OSD will go to sleep until a
button is pressed.
AV AMPLIFIER
An on-screen display (OSD) appears on your TV. Use the
/// hard keys and ENTER on the remote control
to navigate through the screens and select menu items.
• The / (cursor up/down) hard keys select menu
items and the / (cursor left/right) hard keys
change the setting of the item selected.
Caution
• The test tones used in the Auto Surround Setup are
output at high volume.
39
En
Getting started
04
4 ‘Auto Surround Setup’ should be highlighted.
Press ENTER.
8 Confirm the speaker configuration in the OSD.
The configuration shown on-screen should reflect the
actual speakers you have.
System Setup
[ Auto Surround Setup ]
[1.
[2.
[3.
[4.
• Do not to turn down the volume during the test tones.
This may result in incorrect speaker settings.
Input Assign]
Surround Setup]
Expert Setup]
THX Audio Setup]
Check!!
FRONT
[
CENTER
[
SURROUND [
SURR BACK [
SUB WOOFER [
[Exit]
5 Specify how you are using your speaker system.
Highlight ‘Go Next’ then press ENTER.
If you are using a normal surround setup, or if you’re not
sure, leave the settings at their default:
• Speaker System Select – Normal Surround
• SP-B (speaker system B) – Second Zone
• X-Curve – ON
For settings other than the default, see Speaker Systems
on page 58.
Auto Surround Setup
Speaker System Select
[ Normal Surround ]
SP–B
X–Curve
[ ON ]
Auto Surround Setup
•Connect microphone
•Please be quiet
•Move obstacles away
•If you have a subwoofer
turn power on and
turn volume up
Auto Surround Setup
Now Analyzing •••
Please Wait
• Make sure the microphone is connected.
• If you’re using a subwoofer, switch it on and turn up
the volume.
• See below for notes regarding high background
noise levels and other possible interference.
7 Make sure ‘Start’ is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
Auto Surround Setup
Auto Surround Setup
Please Wait
Environment Check
Ambient Noise
Microphone
Speaker Level
Now Analyzing •••
40
If the configuration is incorrect and you want to input the
settings manually, select ERRFix SP then press
ENTER. Use / (cursor up/down) to select the speaker
then / (cursor left/right) to specify the size (and
number for surround back). When you’re finished, go to
the next step.
Auto Surround Setup
[Start]
[Cancel]
En
If the speaker configuration displayed isn’t correct, use
the / (cursor up/down) buttons to select Retry, then
press ENTER. Follow the instructions from step 6.
9 Make sure ‘OK, Go Next’ is selected, then press
ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, and acoustic calibration EQ.
Follow the instructions on-screen.
Caution!!
Test tone is
output loudly.
[Cancel]
[OK,Go Next]
[Retry]
[ERR Fix SP.]
[Return to Menu]
If you see an ERR message in the right side column, there
may be a problem with the speaker connection. If
selecting Retry (above) doesn’t fix the problem, turn off
the power and check the speaker connections.
[Second Zone]
[Go Next]
[Return]
6
YES ]
YES ]
YES ]
YES X2]
YES ]
[Cancel]
[OK]
[OK]
[OK]
Caution!!
Test tone is
output loudly.
[Cancel]
Surround Analysis
Speaker Systems
Speaker Distance
Channel Level
Acoustic Cal EQ
[OK]
[OK]
[OK]
[OK]
[Cancel]
Again, try to be as quiet as possible while this is
happening. It may take up to 6 minutes.
Getting started
10 The Auto Surround Setup has finished! Press
SYSTEM SETUP to exit the System Setup menu.
Auto Surround Setup
! ! Complete ! !
[Data Copy]
[Check]
04
• Check that your DVD player/satellite receiver is
set to output Dolby Digital, DTS and 88.2/96kHz PCM
(2 channel) audio.
If there is an option for MPEG audio, set this to convert
the MPEG audio to PCM.
If you connected the multichannel analog outputs of the
player to this receiver, make sure that the player is set to
output multichannel analog audio.
[Return]
The settings made in the Auto Surround Setup should
give you excellent surround sound from your system, but
it is also possible to adjust these settings manually using
the Surround Setup menu (starting on page 57).
If you plan to go on and make advanced settings at this
point, you can select Data Copy to start customizing
your surround sound settings. See Acoustic Calibration
EQ on page 61 for more on this.
You can also choose to view all the settings by selecting
Check. See Checking your surround settings on page 66
for more on this.
If you selected Return, you can select Exit to leave the
System Setup menu screen.
Note
• If you select Cancel at any time during the Auto
Surround Setup, the receiver automatically exits and
no settings will be made.
• Remember to disconnect the microphone after
you’ve finished the Auto Surround Setup.
Other problems when using the Auto
Surround Setup
If the room environment is not optimal for the Auto
Surround Setup (too much background noise, echo off
the walls, obstacles blocking the speakers from the
microphone) the final settings may be incorrect. Check
for household appliances (air conditioner, fridge, fan,
etc.), that may be affecting the environment and switch
them off if necessary.
Note
• Depending on your DVD player or source discs you
may only be able to output analog and stereo digital
audio. In this case you need to change the listening
mode to SURROUND if you want multichannel
surround sound.
Playing a source
Here are the basic instructions for playing a source (such
as a DVD disc) with your home theater system.
1 Turn on the power of the playback component
(for example a DVD player), your TV and subwoofer
(if you have one).
• If your source is the TV’s built-in tuner, then switch to
the channel you want to watch, otherwise make sure
that the TV’s video input is set to this receiver. (For
example, if you connected this receiver to the VIDEO
1 jacks on your TV, make sure that VIDEO 1 input is
now selected.)
2 If the receiver isn’t already on, press
RECEIVER to switch it on.
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
SETUP
Some older TVs may interfere with the operation of the
microphone. If this seems to be happening, switch off the
TV when doing the Auto Surround Setup.
Checking the settings on your DVD
(or other) player
Before continuing, you may want to check the digital
audio output settings on your DVD player and digital
satellite receiver.
41
En
04
Getting started
3 Change the receiver input to the source you
want to play.
You can use the front panel INPUT SELECTOR knob or
the dedicated INPUT buttons on the remote control
touch screen Home menu (see Basic remote control
displays on page 33 if your unsure how to do this).
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
SETUP
4 Start playback of the DVD (or other component).
If you’re playing a Dolby Digital or DTS surround sound
DVD disc, you should hear surround sound. If you are
playing a stereo source, you will only hear sound from the
front left/right speakers in the default listening mode.
• See also Listening to your system on page 43 for
more information on different ways of listening to
sources.
5 Use the MASTER VOLUME control (front panel or
remote) to adjust the volume level.
• Turn down the volume of your TV so that all the sound
is coming from the speakers connected to this
receiver.
Note
• If you need to manually switch the input signal type
from digital to analog (stereo or multichannel), press
SIGNAL SELECT on the front panel or from the
remote control receiver menu (see also Using other
functions on page 75).
• For more detailed surround sound setup, see The
Surround Setup menu on page 57.
• With WMA9 Pro, sound problems may occur
depending on your computer system. WMA9 Pro 7.1
channel 96kHz sources will be downsampled to 5.1
channel 48kHz. If sound problems occur please
connect using the USB interface (see Using the USB
interface on page 87).
42
En
Listening to your system
05
Chapter 5
Listening to your system
About the listening modes
Using this receiver you can enjoy listening to sources,
analog or digital, in either stereo or surround sound.
However, the listening mode options and the current
active mode may change depending on your speaker
setup and the type of source you’re listening to.
Note
• The remote control operations in this section are
accessed from the various receiver menus (for a
more detailed explanation, see Receiver menu
screens on page 34). To go to the receiver menu,
press
from the remote control Home menu
RECEIVER
( ) and use the / (cursor left/right) soft keys to
go to the previous/next screen.
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
RECEIVER
RECEIVER
1/4
Tip
• In the steps below, you can also use the front panel
LISTENING MODE SELECTOR dial instead of the
remote control to select listening modes. Simply turn
the dial to cycle through the available options,
pressing forward to select a mode.
• While listening to a source, press STANDARD for
surround sound playback.
RECEIVER
RECEIVER
1/4
STREAM
DIRECT
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
STREAM
DIRECT
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
SETUP
• You can’t select listening modes when the Stream
Direct mode (see page 47) is switched on.
• With the WMA9 Pro format, 2-channel sources can
only be heard in stereo, and you can’t select the
2 Pro Logic IIx modes with multichannel sources.
Listening in surround sound
Using this receiver, you can listen to any source in
surround sound. However, the options available will
depend on your speaker setup and the type of source
you’re listening to.
If you connected surround back speakers, see also Using
the surround back channel on page 50.
See also Using the Advanced surround effects and Using
the Home THX modes below for further stereo and
surround playback options.
With multichannel sources (such as DVDs and digital
satellite broadcasts), the 2 DIGITAL or DTS indicator on
the front panel lights depending on the source format.
Any active Advanced surround or Home THX mode is
canceled.
With two channel sources, press STANDARD repeatedly
to select from:
• 2 Pro Logic IIx MOVIE – Up to 7.1 channel sound,
especially suited to movie sources (the display shows
5CH MOVIE+VSB with the VSB MODE switched on)
• 2 Pro Logic IIx MUSIC – Up to 7.1 channel sound,
especially suited to music sources(the display shows
5CH MUSIC+VSB with the VSB MODE switched on)
• 2 PRO LOGIC – 4.1 channel surround sound with
sound from the surround speakers in mono (the
display shows 5CH SURR+VSB with the VSB MODE
switched on)
7 CH SURROUND is displayed instead of 2 PRO
LOGIC when the SB CH MODE is switched on
• NEO:6 CINEMA – 6.1 channel sound, especially
suited to movie sources
• NEO:6 MUSIC – 6.1 channel sound, especially suited
to music sources
43
En
05
Listening to your system
With multichannel sources, if you have connected
surround back speaker(s) and have selected SB CH MODE
ON, you can press STANDARD repeatedly to select:
• 2 Pro Logic IIx MOVIE – See above
• 2 Pro Logic IIx MUSIC – See above
• SX (Studio extension) – Adds surround back channel
sound (taken from the left/right surround output) to
5.1 channel sources
• EX (Extension decode) – Creates surround back
channel sound for 5.1 channel sources and provides
pure decoding for 6.1 channel sources (like Dolby
Digital Surround EX and DTS-ES)
Note
2 Use the (OPTION) +/– buttons to adjust the
setting.
Center Width is adjustable between 0 and 7 (default : 3);
Dimension between –3 and +3 (default : 0); Panorama is
On or Off (default : Off).
3
Press OPTION again to adjust other settings.
Note
• If the SB CH MODE is switched to OFF, 2 Pro Logic
IIx (above) becomes 2 Pro Logic II (5.1 channel
sound), however the above setting will still be
effective.
Neo:6 Music settings
• If the SB CH MODE is switched to OFF, or the
surround back speakers are set to NO, 2 Pro Logic
IIx (above) becomes 2 Pro Logic II (5.1 channel
sound).
• In modes that give 6.1 channel sound, the same
signal is heard from both surround back speakers.
When listening in Neo:6 Music mode, you can adjust the
center image to create a wider stereo effect with vocals.
1 With NEO:6 MUSIC mode active, press OPTION
repeatedly to select CENTER IMAGE.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
Dolby Pro Logic IIx Music settings
1 With ‘2 Pro Logic IIx MUSIC’ mode active, press
OPTION repeatedly to select CENTER WIDTH,
DIMENSION or PANORAMA.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
2/4
RECEIVER
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
2/4
RECEIVER
When listening in Dolby Pro Logic IIx Music mode, there
are three further parameters you can adjust: Center
Width, Dimension, and Panorama.
ACOUSTIC
CAL.
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
–
OPTION
+
–
CH LEVEL
+
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
DIGITAL NR
CLASS
STATION
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
ACOUSTIC
CAL.
OPTION
+
–
CH LEVEL
+
TONE
OPTION
DIGITAL NR
CLASS
SB CH
MODE
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
• CENTER WIDTH – Makes the center channel wider
(higher settings) or narrower (lower settings)
• DIMENSION – Makes the sound more distant (minus
settings), or more forward (positive settings)
• PANORAMA – Creates more spacious surround
sound
44
En
VIDEO
L
R
AUDIO
2 Use the (OPTION) +/– buttons to adjust the
setting.
Adjust the effect from 0 (no effect) to 10 (most
prominence given to the center channel). The default
setting is 3.
TUNER
MIDNIGHT
ON/OFF
DIGITAL IN
S-VIDEO
–
MULTI ROOM & SOURCE
CONTROL
VIDEO INPUT
Listening to your system
05
Using the Advanced surround effects
Adjusting the Advanced Surround effect level
The Advanced surround effects can be used for a variety
of additional surround sound effects. The Advanced
Cinema modes are designed to be used with movies, and
the Advanced Concert modes are for music.
You can emphasize or reduce the effect of the Advanced
Surround modes as you like. For each Advanced
Surround mode you can set the effect level
independently.
• Press ADVANCED CINEMA or ADVANCED
CONCERT to select a listening mode.
1 With one of the Advanced surround modes
active, press OPTION repeatedly until EFFECT shows
in the front panel display.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
RECEIVER
RECEIVER
1/4
STREAM
DIRECT
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
2/4
RECEIVER
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
–
OPTION
+
–
CH LEVEL
+
Press ADVANCED CINEMA repeatedly to select from:
• ACTION – Designed for action movies with dynamic
soundtracks
• SCI-FI – Designed for science fiction with lots of
special effects
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
• DRAMA – Designed for movies with lots of dialog
• MUSICAL – Creates a concert hall-type sound for
musicals
• MONOFILM – Creates surround sound from mono
soundtracks
• 5/7-D THEATER – Creates an extra wide stereo field
S-VIDEO
VIDEO
AUDIO
2 Use the (OPTION) +/– buttons to adjust the effect
level.
The effect level can be adjusted from 10 (min) to 90
(max).
Press ADVANCED CONCERT repeatedly to select from:
• CLASSICAL – Gives a large concert hall-type sound
Using the Home THX modes
• CHAMBER – Creates a space with alot of reverb
THX and Home THX are technical standards created by
THX, Ltd. for cinema and home theater sound. Home THX
is designed to make home theater audio sound more like
what you hear in a cinema. See About THX® on page 109
for more on this.
• JAZZ – Creates the sound of a small jazz club
• ROCK – Creates a live concert sound for rock music
• DANCE – Designed for music with lots of bass
• 5/7CH STEREO – Allows you to hear stereo sources
from all the speakers in your setup
Different THX options will be available depending on the
source and the SB CH mode setting (see Using the
surround back channel on page 50 for more on this).
•
Press THX to select a THX listening mode.
RECEIVER
RECEIVER
1/4
STREAM
DIRECT
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
45
En
05
Listening to your system
With two channel sources, press THX repeatedly to select
a matrix-decoding process for the THX CINEMA mode
(see Listening in surround sound above for an
explanation of each process):
• 2 Pro Logic IIx MOVIE
• 2 PRO LOGIC
Listening in stereo
You can hear any source through just the front left and
right speakers (and possibly your subwoofer depending
on your speaker settings).
• While listening to a source, press STEREO for
stereo playback.
• NEO:6 CINEMA
With multichannel sources, press THX repeatedly to
select from:
RECEIVER
RECEIVER
• THX CINEMA – Gives you cinema-quality sound from
your home theatre system using all the speakers in
your setup
• THX SURROUND EX – Allows you to hear 6.1 or 7.1
channel playback with 5.1 channel sources
• 2 Pro Logic IIx MOVIE – Allows you to hear 7.1
channel playback with 5.1 channel sources
(especially suited to movie sources)
• THX ULTRA2 CINEMA – Allows you to hear 7.1
channel playback with 5.1 channel sources
• THX MUSICMODE – Allows you to hear 7.1 channel
playback with DVD-A and SACD multichannel music
sources
1/4
STREAM
DIRECT
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
STEREO shows in the front panel display. Any active
Advanced surround or Home THX mode is canceled.
Dolby Digital and DTS multichannel sources are
downmixed to stereo.
Listening with headphones
Note
• If you only have one surround back speaker
connected, THX ULTRA2 CINEMA and THX
MUSICMODE are not available.
• When selecting the Dolby Pro Logic modes above,
the display shows the mode you selected, then after
a few seconds, shows THX CINEMA.
• You won’t be able to use the THX options when
playing two-channel DVD-A and SACD sources.
• With multichannel DVD-A and SACD sources, you
can only select THX MUSICMODE.
When headphones are connected, only the STEREO
(default) and PHONES SURROUND modes are available.
PHONES SURROUND is a virtual surround sound
experience for headphones which provides realistic and
dynamic surround sound.
When you connect a pair of headphones, the listening
mode automatically changes to STEREO or PHONES
SURROUND. When you disconnect them it reverts to the
previous mode.
• With headphones connected, press STANDARD
to select PHONES SURROUND, or STEREO for stereo
sound.
You can also turn the front panel LISTENING MODE
SELECTOR dial to select either STEREO or PHONES
SURROUND.
Note
• Many features of this receiver are not accessible
when the headphones are connected.
• If the U-shaped connectors (on the rear panel) aren’t
in place, you won’t be able to use the headphones.
• When headphones are connected, no sound is heard
from the speakers.
• If you’re listening to a WMA9 Pro format source, only
STEREO is available.
46
En
Listening to your system
Using the multichannel analog inputs
If you’ve connected to the multichannel inputs on the
rear panel (see Connecting the multichannel analog
outputs on page 18), you will be able to select them as
your input source. See Using the Stream Direct mode
below if you want to bypass the signal processing in this
receiver for a pure analog signal.
1 Press ‘Multi-ch in’ on the remote control Home
menu ( ) screen.
You can also use the INPUT SELECTOR dial on the front
panel.
2/3
HOME
RECEIVER
1
RECEIVER
INPUT 2
3
CD-R
/ TAPE1
VCR2
VCR3
VIDEO
MULTI CH
INPUT
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
SETUP
2 If necessary, press SIGNAL SELECT to choose the
number of channels you’ll hear.
See Selecting USB and multichannel analog input
channels on page 49 for more on this.
Note
• The number of channels you hear will depend on the
source and the SB CH mode setting (see Using the
surround back channel on page 50 for more on this).
Using the Stream Direct mode
• Default setting: SD:1 NORMAL (on)
Use the Stream Direct mode when you want to hear the
truest possible reproduction of a source. All unnecessary
signal processing is bypassed, and you’re left with the
pure analog or digital sound source.
1 While listening to a source, press STREAM
DIRECT to switch on or off.
RECEIVER
RECEIVER
1/4
STREAM
DIRECT
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
05
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
2 If you want to change the Stream Direct mode,
press OPTION repeatedly to select Stream Direct
(appears on the front panel as SD:1, 2 or 3) then use
the (OPTION) +/– buttons to adjust the setting.
• SD:1 NORMAL – Analog and digital sources are
heard according to the settings made in the
Surround Setup (speaker setting, channel level,
speaker distance, acoustic calibration EQ, and Xcurve), as well as with dual mono, the input
attenuator, and any sound delay and hi-bit/hisampling settings. You will hear sources according to
the number of channels in the signal.
• SD:2 2CHDIRECT – Use this setting for stereo
analog and digital sources. All processing
unnecessary for 2-channel signals is bypassed (such
as speaker distance and acoustic calibration EQ) and
you will hear the source through the shortest
possible signal path. All sound will be heard through
the front left and right speakers only (no subwoofer
output is heard). With multichannel sources,
playback is the same as the NORMAL setting
(above).
• SD:3 ANADIRECT – All analog sources are heard
without any digital processing. All processing is done
through the analog circuitry and the center channel,
if present, will be sent to the front right and left
speakers (the channel level is adjusted
automatically). With digital sources, playback is the
same as the NORMAL setting (above).
Note
• You can’t use Digital NR, Midnight/Loudness
listening, the SB CH mode, the tone control, or any of
the listening modes when Stream Direct is on.
• If you connect the headphones when SD:3
ANADIRECT is selected, only the front left and
right channels will be heard with multichannel
sources.
• Stereo formats with surround sound information
(such as Dolby Surround) are treated the same as
multichannel sources.
• When the speaker impedance is set to 4Ω in
Switching the speaker impedance on page 78, or
when the Digital Safety is switched on (see
Troubleshooting section on Power on page 99), the
setting is fixed at SD:1 NORMAL.
47
En
05
Listening to your system
Listening with Acoustic Calibration
EQ
You can listen to sources using the Acoustic Calibration
Equalization set in Automatically setting up for surround
sound on page 39 or Acoustic Calibration EQ on page 61.
Refer to these pages for more on acoustic calibration
equalization.
• Press SIGNAL SELECT to select the type of input
signal for the current source.
With the remote, you may need to press
Home menu ( ) first before reaching the receiver menu
screen shown below (use the / (cursor left/right)
soft keys to go to the previous/next menu screen).
• While listening to a source, press ACOUSTIC CAL.
to select an Acoustic Calibration EQ setting.
RECEIVER
RECEIVER
1/4
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
ACOUSTIC
CAL.
1/4
STREAM
DIRECT
RECEIVER
STREAM
DIRECT
RECEIVER
on the
RECEIVER
SIGNAL
SELECT
ACOUSTIC
CAL.
LISTENING
MODE
STEREO
STANDARD
THX
ADVANCED
CINEMA
ADVANCED
CONCERT
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
Press repeatedly to choose between:
VIDEO INPUT
PHONES
VIDEO
ON/OFF
L
AUDIO
R
• ANALOG – Selects an analog signal.
•
Press repeatedly to select between:
• ALL CH ADJ – No special weighting is given to any
one channel.
• FRONT CH ALIGN – All speakers are heard in
accordance with the front speaker settings.
• CUSTOM 1/2 – Custom settings
– Selects an i.LINK signal.
• DIGITAL – Selects an optical or coaxial digital signal.
• 2 RF – Selects a 2 RF signal.
• AUTO – This is the default setting. The receiver
selects the first available signal in the following
order:
; 2 RF; DIGITAL; ANALOG.
• OFF – Switches Acoustic Calibration EQ off.
Note
Selecting the input signal type
Most of the audio inputs have both analog and digital
jacks. You can select the type of signal to be used in each
case.
The input signal type for the current input is indicated in
the display. With digital signals, the signal type (Dolby
Digital or DTS) also shows in the display.
The default AUTO setting is usually sufficient, letting the
receiver decide the most suitable signal type. However, if
you want to record from the DVR/VCR1 IN/OUT jacks,
then you should set the input signal type to analog.
If you have selected the USB interface or the
multichannel analog inputs as your input source, see
Selecting USB and multichannel analog input channels
below.
• If no digital inputs (including the 2 RF input) are
assigned for the current source, the input signal type
will default to ANALOG.
• When using DIGITAL IN terminals the following
digital signal formats are supported: Dolby Digital,
DTS and PCM (32, 44.1, 48, 88.2 and 96 kHz sampling
frequencies). If you are using the i.LINK connectors,
DVD-A (including 176.4/192 kHz) and SACD are also
supported. If your source is not supported, select
ANALOG.
• Some DVD players don’t output DTS signals. For
more details, refer to the instruction manual supplied
with your DVD player.
• Even when i.LINK is selected and the i.LINK indicator
lights, you won’t hear any sound if the output settings
of your i.LINK device are off.
• The audio signal from karaoke microphones and
some LDs is not output from the digital outputs.
Select ANALOG to listen to these formats.
48
En
Listening to your system
• If you want to play DTS-encoded sources, you need to
have digital connections. If ANALOG is selected,
you’ll hear digital noise through your speakers.
• Make sure you connect your DVD/LD or LD players
using the 2 RF jack. If your player has a 2 RF
output this will ensure you can use all LDs. Refer to
Connecting other video sources on page 21.
• The input signal for unassigned i.LINK-equipped
components is fixed to
inputs on page 91.
. See Assigning the i.LINK
Selecting USB and multichannel analog input
channels
When you’ve selected the USB interface or the
multichannel analog inputs as your input source, the
SIGNAL SELECT button is used to specify the number of
input channels.
• After selecting USB or MULTI CH IN as your input
source, press SIGNAL SELECT to choose the number
of input channels.
Select one of the following options:
• 2 CHANNEL
05
• Select the STEREO or STANDARD listening mode
and switch off any other sound processing features.
These features include:
• Real Phantom (page 51)
• Virtual Surround Back (page 51)
• Midnight/Loudness (page 52)
• Digital Noise Reduction (page 53)
• Dynamic Range Control (page 94)
Note that you’ll still be able to use the tone control (see
Using the tone control on page 52).
Note
• You will see the sampling frequency in the display
(with DTS 96kHz (24-bit) sources, 96 is only displayed
when the signal is being processed at 96kHz).
• Even if your DVD player can’t output 96kHz (24-bit)
digital signals, you can still listen to DTS 96/24
sources processed at 96kHz if it has a DTS output
feature. Other formats (such as PCM192/96kHz
sources) are not compatible unless the digital output
of your DVD player supports high-sampling digital
signals.
• 6 CHANNEL
• 7 CHANNEL
• 8 CHANNEL
The 8 CHANNEL setting is the default.
Listening to high-sampling formats
This receiver supports 88.2/96kHz (24-bit) digital formats
(such as DTS 96/24 and PCM 96kHz sources up to 24-bit)
when connected to a compatible DVD player with digital
connections. If you have connected this receiver to an
i.LINK-equipped component, 176.4/192kHz (24-bit) digital
formats (such as DVD-A and SACDs) are also supported.
You can listen to these formats without downsampling in
one of three ways:
• Switch the Stream Direct mode on.
See Using the Stream Direct mode on page 47.
For the following options, the 2 Pro Logic modes cannot
be selected for DTS 96kHz (24-bit) sources without
downsampling:
• Select one of the Home THX modes.
See Using the Home THX modes on page 45.
49
En
05
Listening to your system
Using the surround back channel
• Default setting: SB CH ON
You can have the receiver automatically use 6.1 or 7.1
decoding for 6.1 encoded sources (for example, Dolby
Digital EX or DTS-ES), or you can choose to always use
6.1 or 7.1 decoding with other sources (for example, 5.1
encoded material). With 5.1 encoded sources, a
surround back channel will be generated, but the
material may sound better in the 5.1 format for which it
was originally encoded, in which case you can simply
switch the surround back channel off. The table below
indicates when you will hear the surround back channel
when playing various kinds of sources. (=Sound plays
through surround back channel speaker(s); = 7 CH
SURROUND shows in the display; = Home THX is
selected and two surround back speakers are connected)
Standard / THX
SB CH
mode
Type of source
Dolby Digital EX/DTS-ES encoded
multichannel source with 6.1ch
surround
Stereo sources
Multichannel
sources
2 Pro Logic II x 2 Pro Logic
AUTO
ON
AUTO
ON
AUTO
ON
AUTO
Dolby Digital/DTS encoded stereo
source; other digital stereo source
Analog 2-channel (stereo) source
• Press SB CH MODE repeatedly to cycle through
the surround back channel options.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
TV
CONT
SB CH
MODE
INPUT
ACOUSTIC
CAL.
SPEAKER
A/B
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
SB CH
MODE
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
Each press changes the setting as follows (see the table
above for an explanation of each):
• SB CH AUTO – Automatically switches to 6.1 or 7.1
decoding for 6.1 encoded sources (for example,
Dolby Digital EX or DTS-ES)
• SB CH ON – 6.1 or 7.1 encoding is always used (for
example, on 5.1 encoded material)
50
En
• SB CH OFF – Surround back channel is switched off
Note
• If the surround back speaker is set to NO in Speaker
Systems on page 58, or you have selected SPA+B
as the speaker setting, you can only use the virtual
surround back effect (see next page).
TUNER
MIDNIGHT
• You will only hear the surround back channel when
you’ve selected SPA as the speaker setting (see
Switching the speaker system on page 80). Changing
the speaker system may automatically change this
setting (see notes below).
3/4
RECEIVER
NEO:6
ON
Dolby Digital/DTS encoded
multichannel source
RECEIVER
Advanced
surround
• You can’t select the surround back channel setting (it
is automatically switched off) when you’ve selected
SPB as the speaker setting or when Bi-Surround is
selected in Speaker Systems on page 58.
• You can’t use the surround back channel setting
when Stream Direct is on or when the STEREO mode
is selected.
• When the THX mode is selected, you can’t select SB
CH OFF if you’re listening to DVD-Audio or SACD.
Listening to your system
05
Listening with virtual surround back
speakers
• Default setting: VIRTUAL SB OFF
If you don’t have real surround back speakers connected,
you can use the Virtual Surround Back feature to
simulate one.
Sometimes the material may sound better in the 5.1
format for which it was originally encoded. In this case
you can have the receiver only apply this effect to 6.1
encoded sources like Dolby Digital EX or DTS-ES (VSB
AUTO), or you can simply switch it off (VSB OFF).
Creating a center speaker effect
If you don’t have a center speaker connected, the center
speaker channel is mixed to your two front speakers.
However, using the Real Phantom setting, you can create
a center speaker effect for an effective front surround
effect.
1 Press OPTION repeatedly to select R.PHANTOM.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
See also Using the surround back channel above.
• Press SB CH MODE repeatedly to cycle through
the virtual surround back channel options.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
2/4
RECEIVER
Note that this feature only works when the surround
channels are active and the surround back speaker is set
to NO in Speaker Systems on page 58. It is also available
when the speaker system has been set to SPAB (see
Switching the speaker system on page 80).
ACOUSTIC
CAL.
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
–
OPTION
+
–
CH LEVEL
+
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
3/4
RECEIVER
S-VIDEO
TV
CONT
RECEIVER
TAPE2
MONITOR
INPUT
SB CH
MODE
SPEAKER
A/B
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
VIDEO
AUDIO
2 Use the (OPTION) +/– buttons to change the
setting.
• Mid – A subtle center speaker effect is applied to the
front left and right channels.
• Max – A strong center speaker effect is applied to the
front left and right channels.
• OFF – The center speaker effect is switched off.
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
Note
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
Each press cycles through the options as follows:
• VSB AUTO
• Real Phantom is automatically switched off and
R.PHANTOM won’t appear in the display (in step 1) if
Stream Direct or the STEREO listening mode is
switched on. The center speaker must also be set to
NO in Speaker Systems on page 58.
• VSB ON
• VSB OFF
Note
• You can’t select the virtual surround back setting
when you’ve selected SPB as the speaker setting
(see Using speaker system B on page 80) or when BiSurround is selected in Speaker Systems on page 58.
• You can’t use the virtual surround back setting when
Stream Direct is on or when STEREO, or one of the
THX modes is selected.
51
En
05
Listening to your system
Using Hi-bit and Hi-sampling
You can use both Hi-bit and Hi-sampling to create a wider
dynamic range with digital sources like CDs or DVDs.
1 Press OPTION repeatedly to select HI-BIT or HISAMPLING.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
2/4
RECEIVER
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
–
OPTION
+
–
CH LEVEL
+
Note
• You can’t use the Midnight and Loudness modes at
the same time.
• You can’t use either of these modes when using the
tone controls, or Stream Direct or the Home THX
modes.
• Midnight and Loudness automatically adjust
according to the volume at which you’re listening.
However, the volume must be under -20dB for these
features to take effect.
Using the tone control
You can use the tone control to make customized
settings for the bass and treble.
Switching the tone control on or off
• Default setting: BYPASS
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
You’ll need to switch the tone control on to adjust the
bass and treble below.
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
2 Use the (OPTION) +/– buttons to switch the
selected mode on or off.
• Press TONE to switch the tone control on or off.
When the tone control is switched off, BYPASS shows in
the display. The remote control menu for this step is
shown below (see note at the start of this chapter if you
need help).
Note
2/4
RECEIVER
• Hi-bit and Hi-sampling may not work with Stream
Direct or analog sources.
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
• You can’t use Hi-bit with SACD or sources over
88.2kHz when using one of the digital inputs
(including i.LINK).
TONE
LOUDNESS
–
OPTION
+
–
CH LEVEL
+
Using Midnight and Loudness
listening
• Default setting: Off
ACOUSTIC
CAL.
The Midnight listening feature allows you to hear
effective surround sound of movies at low volume levels.
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
52
En
VIDEO
AUDIO
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
The Loudness feature is useful for listening to music
sources at low volumes.
• Press MIDNIGHT or LOUDNESS to switch the
effect on or off.
LOUDNESS is only available when using the remote
control. The remote menu for this step is shown below
(see note at the start of this chapter if you need help).
SB CH
MODE
TUNER
MIDNIGHT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
Note
• You can’t use the tone control with Stream Direct,
Midnight, Loudness, or any of the Home THX modes.
Listening to your system
05
Adjusting the bass and treble
Listening to dual mono soundtracks
• Default setting: Bass: 0, Treble: 0
You can specify how dual mono encoded Dolby Digital
soundtracks should be played. Dual mono is not widely
used, but is sometimes necessary when two languages
need to be sent to separate channels.
You can adjust the bass and treble controls separately to
adjust the overall tone.
1 Press OPTION repeatedly to select BASS or
TREBLE.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
RECEIVER
TV
CONT
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
MIDNIGHT
DIGITAL NR
LOUDNESS
TONE
LOUDNESS
TONE
–
–
OPTION
CH LEVEL
+
–
OPTION
+
+
–
CH LEVEL
+
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
PHONES
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
• Press the DIGITAL NR button to switch digital
noise reduction on or off.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
SB CH
MODE
TUNER
OPTION
DIGITAL NR
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
ON/OFF
L
R
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
• CH1/CH2 – Both channels are played through the
front speakers
If you have a noisy source (for example, cassette or video
tape with lots of background noise), you may be able to
improve the quality of the sound by switching on digital
noise reduction (DIGITAL NR).
TONE
OPTION
• CH2 – Only channel 2 is played
Reducing noise during playback
MIDNIGHT
TONE
2 Use the (OPTION) +/– buttons to change the
setting.
• CH1 – Only channel 1 is played
Press ENTER to confirm.
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
R
2 Use the (OPTION) +/– buttons to adjust the
sound.
The bass and treble can be adjusted from –6 to +6.
3
ACOUSTIC
CAL.
VIDEO INPUT
VIDEO INPUT
PHONES
2/4
RECEIVER
2/4
RECEIVER
ACOUSTIC
CAL.
1 Press OPTION repeatedly to select DUAL MONO.
The remote control menu for this step is shown below
(see note at the start of this chapter if you need help).
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
Note
• On the CH1 and CH2 settings the sound comes only
from the center speaker (or from the front speakers if
NO was selected for the center speaker setting).
• This setting works only with dual mono encoded
Dolby Digital and DTS soundtracks.
• When listening to a dual mono source, the L and R
indicators on the front panel flash. The channel you
select will light in the display.
VIDEO INPUT
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
Note
• Depending on the source, there may not be a
noticeable improvement in the quality of the sound.
• You can’t use digital noise reduction with Stream
Direct or the Home THX modes.
53
En
06
Using the tuner
Chapter 6
Using the tuner
Finding a station
Note
• The remote control operations in this section are
accessed from the remote control tuner menus. If
you’re not sure how to navigate the touch panel, see
Basic remote control displays on page 33. To go to the
tuner menu, press TUNER on the remote control
Home menu ( ):
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
TUNER
SAT
DVR
/ VCR1
CD
TV
CONT
MULTI
OPERATION
–
STATION
TUNER
–
TUNING
+
SYSTEM
OFF
BAND
CLASS
MPX
1/2
TUNER
2/2
TV
CONT
–
TV
CONT
STATION
+
1
2
3
–
TUNING
+
4
5
6
BAND
CLASS
MPX
7
8
9
DISP MODE TUNER EDIT
+
DISP MODE TUNER EDIT
SETUP
TUNER
1/2
TV
CONT
3
TV
/ DVD
DVD
/ LD
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the
exact frequency of the station you want to listen to, see
Tuning directly to a station below. Once you are tuned to
a station you can memorize the frequency for recall
later—see Memorizing station presets on page 55 for
more on how to do this.
DIRECT
ACCESS
1 Press BAND to change the band (FM or AM), if
necessary.
Each press switches the band between FM and AM.
2
0
Tune to a station using the TUNING +/– buttons.
Automatic tuning
To search for stations in the currently selected band,
press and hold either of the TUNING +/– buttons for
about a second. The receiver will start searching for
the next station, stopping when it has found one.
Repeat this step to search for other stations.
Manual tuning
To change the frequency one step at a time, press the
TUNING +/– buttons repeatedly.
High speed tuning
Press and hold the TUNING +/– buttons for high speed
tuning, releasing the button once you reach the
frequency you want.
54
En
Using the tuner
06
Tuning directly to a station
MPX mode
Sometimes, you'll already know the frequency of the
station you want to listen to. In this case, you can simply
enter the frequency directly using the number buttons on
the remote control.
If there is interference or noise during a stereo FM radio
broadcast (the STEREO indicator is lit), or the radio
reception is weak, press MPX on the tuner touch screen
menu to switch the receiver into mono reception mode
(the MONO indicator lights). This should improve the
sound quality and allow you to enjoy the broadcast.
TUNER
1/2
TV
CONT
–
STATION
+
–
TUNING
+
BAND
CLASS
MPX
DISP MODE TUNER EDIT
TUNER
1/2
TV
CONT
–
STATION
+
–
TUNING
+
BAND
CLASS
MPX
DISP MODE TUNER EDIT
1 On the tuner touch screen menu, press BAND to
change the band (FM or AM), if necessary.
Each press switches the band between FM and AM.
2
Press DIRECT ACCESS.
TUNER
2/2
TV
CONT
1
2
3
4
5
6
8
9
7
0
DIRECT
ACCESS
Memorizing station presets
If you often listen to a particular radio station, it's
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time. The
receiver can memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations each. When
memorizing FM frequencies, the receiver also stores the
MPX setting (see MPX mode above).
TUNER
1/2
TV
CONT
3 Use the number buttons to enter the frequency
of the radio station.
For example, to tune to 106.00 (FM), press 1, 0, 6, 0, 0.
–
STATION
+
–
TUNING
+
BAND
CLASS
MPX
DISP MODE TUNER EDIT
Note
• If you make a mistake while inputting the frequency,
press the DIRECT ACCESS button again to cancel the
frequency and start again.
1 Tune to a station you want to memorize.
See Finding a station on page 54 and Tuning directly to a
station above for more details on how to do this.
2 Press TUNER EDIT.
The display shows MEMORY INPUT then a blinking
memory class (A, B or C).
3 Press CLASS to select one of the three classes.
Press repeatedly to cycle through the three memory
classes, A, B and C.
4 Use the STATION +/– buttons (or number
buttons) to select the station preset you want.
Press STATION +/– repeatedly to select a preset
number.
55
En
Using the tuner
06
5
While the display is blinking, press ENTER.
Listening to memorized station presets
6
Repeat steps 1 – 5 to memorize up to 30 stations.
You can do this from both the remote control and the
front panel.
Naming station presets
You can input a name of up to eight characters for each
preset station in the receiver’s memory. For example, you
could input New Jazz for that station and when you
listen to it the name, rather than the frequency, will
appear in the display.
1 Press CLASS repeatedly to select the class.
Press repeatedly to cycle through the three memory
classes, A, B and C.
2 Use the STATION +/– buttons to select an FM or
AM preset station.
3 Press TUNER EDIT to select the station name
mode (NAME INPUT).
4 Edit the name as necessary and press ENTER.
Use the / (cursor up/down) hard keys to change the
character and the / (cursor left/right) hard keys to
move forward/back a position. The name can be up to
eight characters (the possible characters are listed
below).
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
!”#$%&’()*+,–./:;<=>[email protected][ \ ]
Any time you want to exit the process, press the TUNER
EDIT button.
5
Press ENTER when you’re done.
6 Repeat steps 2 – 5 to memorize up to 30 preset
broadcast station names.
Tip
• To change a station name, just enter the new name
over the top of the old one. To erase a station name,
enter a new name of eight spaces.
• You can switch between the frequency display and
the station name display using the DISP MODE
button.
56
En
TUNER
1/2
TV
CONT
–
STATION
+
–
TUNING
+
BAND
CLASS
MPX
DISP MODE TUNER EDIT
1 Press CLASS to select the class in which the
station is stored.
Press repeatedly to cycle through the three memory
classes, A, B and C.
2 Use the STATION +/– buttons to select the station
memory in which the station is stored.
You can also use the number buttons on the remote
control to recall the station preset.
The Surround Setup menu
07
Chapter 7
The Surround Setup menu
Making receiver settings from the
Surround Setup menu
2 Using the remote control, press RECEIVER on the
touch screen, then press the SYSTEM SETUP button.
This receiver allows you to make detailed settings to
optimize the surround sound performance. You only
need to make these settings once (unless you change the
placement of your current speaker system or add new
speakers.).
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
These settings are designed to fine-tune your system, but
if you’re satisfied with the settings made in Introduction
to home theater on page 39, it isn’t necessary to make all
of these settings.
2
3
DVD
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
SETUP
Important
• For many of the settings below, you’ll have to connect
the setup microphone to the front panel and place it
about ear level at your normal listening position. See
Introduction to home theater on page 39 if you’re
unsure how to do this. Also see Other problems when
using the Auto Surround Setup on page 41 for notes
regarding high background noise levels and other
possible interference.
• If you’re using a subwoofer, switch it on and turn up
the volume to the middle position.
• After three minutes of inactivity during the Auto
setup options (including Professional Acoustic
Calibration EQ measurement), the OSD will go to
sleep until a button is pressed. With other screens,
the receiver automatically exits and no settings will
be made.
ENTER
CHANNEL
MENU
VOLUME
MUTE
SYSTEM
SETUP
AV AMPLIFIER
An on-screen display (OSD) appears on your TV. Use the
/// hard keys and ENTER on the remote control
to navigate through the screens and select menu items.
• The / (cursor up/down) hard keys select menu
items and the / (cursor left/right) hard keys
change the setting of the item selected.
3
Select ‘Surround Setup’ then press ENTER.
System Setup
[Auto Surround Setup]
Caution
• The test tones used in the Surround Setup are output
at high volume (the volume increases to 0db
automatically).
1 Switch on the receiver and your TV.
If headphones are connected to the receiver, disconnect
them.
[1.
[2.
[3.
[4.
Input Assign ]
Surround Setup ]
Expert Setup ]
THX Audio Setup ]
[Exit]
4 Select the setting you want to adjust.
If you are doing this for the first time, you may want to
adjust these settings in order:
2.Surround Setup
[ Check ]
[
[
[
[
[
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
[Return]
• Speaker Systems – Specify the size and number of
speakers you’ve connected (page 58).
57
En
The Surround Setup menu
07
• Channel Level – Adjust the overall balance of your
speaker system (page 60).
3
2.1.Speaker Systems
Manual Free
• Speaker Distance – Specify the distance of your
speakers from the listening position (page 61).
Speaker System Select
• Acoustic Cal EQ – Adjust overall equalization
depending on your room characteristics (page 61).
• X-Curve – Adjust the amount of ‘re-equalization’
necessary to achieve a flat frequency response from
your home theater system (page 65).
5 Make the adjustments necessary for each
setting, pressing ENTER to confirm after each screen.
When you’re finished, you can check through your
settings screen by screen by selecting Check from the
Surround Setup menu (see Checking your surround
settings on page 66 for more on this).
[Normal Surround ]
_
SP B:
[ Second Zone
1
]
[ Next]
Use / (cursor left/right) to cycle through the
following options:
• Normal Surround – Select for normal home theater
use.
• Front Bi-Amp – Select this setting if you’re biamping your front speakers (see Bi-amping your front
speakers on page 81).
• Bi-Surround – Select if you’re using two sets of
surround speakers (see Adding a second set of
surround speakers for Bi-Surround on page 82).
Speaker Systems
You need to specify the number of speakers you have in
your system, and how you want to route the sound. It is a
good idea to make sure that the settings made in
Introduction to home theater on page 39 are correct.
Specify how your speakers are configured.
If you selected Normal Surround, you’ll also have to
select the speaker system B setting:
Select ‘Speaker Systems’ then press ENTER.
2.1.Speaker Systems
Manual Free
Speaker System Select
2.Surround Setup
[Normal Surround ]
_
[ Check ]
[
[
[
[
[
SP B:
[ Second Zone
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
]
[ Next]
• Second Zone – Select if you want to hear speaker
system B in a separate room.
[Return]
2 Select how you want to set up your speakers
then press ENTER.
• ITU-R – Select this setting to use two switchable
main speaker systems using speaker system B (see
Alternating surround speaker setups using speaker
system B (ITU-R) on page 80).
2.1. Speaker Systems
[Manual Free]
[Manual THX]
(all small)
[Auto]
• OFF – Select if no speakers are connected to the B
terminals.
[Return]
4
• Manual Free – Manually set all speakers.
• Manual THX – All speakers are set to SMALL. You
can only select the number of surround back
speakers.
• Auto – All speakers are set automatically. (The
microphone must be hooked up to the front panel to
do this.)
58
En
Press ENTER to go to the next screen.
• If you selected Auto in step 2, you will have to select
Next and then press ENTER to continue to the auto
(test tone) setup.
Select Start and press ENTER to start the test tones
when you’ve made sure the room is free of ambient noise.
Go to step 8 when you see OK appear on the OSD.
The Surround Setup menu
07
• If you select SMALL for the front speakers the
subwoofer will automatically be fixed to YES. Also,
the center and surround speakers can’t be set to
LARGE if the front speakers are set to SMALL. In this
case, all bass frequencies are sent to the subwoofer.
5 Choose the set of speakers that you want to set
then select a speaker size.
2.1. Speaker Systems
Manual Free
” Normal Surround ”
FRONT
CENTER
SURROUND
SURR BACK
SUB WOOFER
[ LARGE ]
[ LARGE ]
[ LARGE ]
[LARGE X2]
[ YES ]
• If the surround speakers are set to NO, the surround
back speakers will automatically be set to NO.
• If you select one surround back speaker only, make
sure that speaker is hooked up to the left surround
back terminal.
( NEXT)
Use / (cursor left/right) to select the size (and
number) of each of the following speakers:
• FRONT – Select LARGE if your front speakers
reproduce bass frequencies effectively, or if you
didn’t connect a subwoofer. Select SMALL to send
the bass frequencies to the subwoofer.
• CENTER – Select LARGE if your center speaker
reproduces bass frequencies effectively, or select
SMALL to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect a center
speaker, choose NO (the center channel is sent to
the front speakers).
• SURROUND – Select LARGE if your surround
speakers reproduce bass frequencies effectively.
Select SMALL to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect
surround speakers choose NO (the sound of the
surround channels is sent to the front speakers or a
subwoofer).
• SURR BACK – Select the number of surround back
speakers you have (one, two or none). Select LARGE
if your surround back speakers reproduce bass
frequencies effectively. Select SMALL to send bass
frequencies to the other speakers or subwoofer. If
you didn’t connect surround back speakers choose
NO.
• SUBWOOFER – LFE signals and bass frequencies of
channels set to SMALL are output from the
subwoofer when YES is selected (see notes below).
Choose the PLUS setting if you want the subwoofer to
output bass sound continuously or you want deeper
bass (the bass frequencies that would normally come
out the front and center speakers are also routed to
the subwoofer). If you did not connect a subwoofer
choose NO (the bass frequencies are output from
other speakers).
6
Press ENTER to go to the next screen.
7 Choose a crossover frequency.
This setting decides the cutoff between bass sounds
playing back from the speakers selected as LARGE, or
the subwoofer, and bass sounds playing back from those
selected as SMALL. It also decides where the cutoff will
be for bass sounds in the LFE channel.
2.1. Speaker Systems
Manual Free
” Normal Surround ”
Crossover
[ 80Hz ]
Normal Surround
(THX Speaker = 80Hz)
SP-B : Second Zone
[Return]
Use / (cursor left/right) to select the crossover
frequency:
• 50Hz – Sends bass frequencies below 50 Hz to the
subwoofer (or LARGE speakers).
• 80Hz – Sends bass frequencies below 80 Hz to the
subwoofer (or LARGE speakers).
• 100Hz – Sends bass frequencies below 100 Hz to the
subwoofer (or LARGE speakers).
• 150Hz – Sends bass frequencies below 150 Hz to the
subwoofer (or LARGE speakers).
• 200Hz – Sends bass frequencies below 200 Hz to the
subwoofer (or LARGE speakers).
Note
• If you selected Manual THX (in step 2) the crossover
frequency is set to 80Hz and this screen doesn’t
appear.
8 Select ‘Return’ and press ENTER to return to the
Surround Setup menu.
Note
• If you selected Manual THX (in step 2) you can only
adjust the surround back settings.
• If you selected Front Bi-Amp (in step 3) you can’t
adjust the surround back settings.
Tip
• If you have a subwoofer and like lots of bass, it may
seem logical to select LARGE for your front speakers
and PLUS for the subwoofer. This may not, however,
yield the best bass results. Depending on the speaker
placement of your room you may actually experience
59
En
The Surround Setup menu
07
a decrease in the amount of bass due low frequency
cancellations. In this case, try changing the position
or direction of speakers. If you can’t get good results,
listen to the bass response with it set to PLUS and
YES or the front speakers set to LARGE and SMALL
alternatively and let your ears judge which sounds
best. If you’re having problems, the easiest option is
to route all the bass sounds to the subwoofer by
selecting SMALL for the front speakers.
3 If you selected ‘Manual’ or ‘Semi Auto’, adjust
the level of each channel using the / (cursor left/
right) hard keys.
If you selected Manual, use / (cursor up/down) to
switch speakers. The Semi Auto setup will output test
tones in the order shown on-screen:
2.2. Channel Level
Semi Auto
LEFT
[ + 1. 5dB ]
CENTER
[ + 1. 5dB ]
RIGHT
[ + 2. 0dB ]
SURROUND R [ - 3. 5dB ]
SURR BACK R [ - 1. 5dB ]
SURR BACK L [ + 3. 0dB ]
SURROUND L [ + 2. 0dB ]
SUB WOOFER [+ 10. 0dB ]
Return = Push Enter
Channel Level
Using the channel level settings, you can adjust the
overall balance of your speaker system, an important
factor when setting up a home theater system. If you’re
unsure of the best channel level settings, simply select
Auto from the setup options below.
1
Adjust the level of each speaker as the test tone is
emitted.
Select ‘Channel Level’ then press ENTER.
Note
2.Surround Setup
[ Check ]
[
[
[
[
[
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
[Return]
2 Select a setup option and press ENTER to start
the test tones.
2.2. Channel Level
[Manual]
[Semi Auto]
[Auto]
Normal Surround
[Return]
• If you are using a Sound Pressure Level (SPL) meter,
take the readings from your main listening position
and adjust the level of each speaker to 75 dB SPL (Cweighting/slow reading).
• The subwoofer test tone is output at low volumes. You
may need to adjust the level after testing with an
actual soundtrack.
4 If you selected ‘Manual’ or ‘Auto’, select ‘Return’
then press ENTER to finish. With ‘Semi Auto’, simply
press ENTER.
With the Auto setup, !! Complete !! is displayed onscreen after the channel levels are set.
2.2. Channel Level
Your Speaker Systems
” Normal Surround ”
[Manual]
[Semi Auto]
[Auto]
Normal Surround
[Return]
• Manual – Move the test tone manually from speaker
to speaker and adjust individual channel levels.
Your Speaker Systems
” Normal Surround ”
• Semi Auto – Adjust channel levels as the test tone
moves from speaker to speaker automatically.
• Auto – The levels are set automatically by the
receiver as it outputs the test tones. (For this setup
you must have the mic connected.)
To check the settings, select Check and press ENTER
instead of selecting Return above. When you’re finished
select Return then press ENTER.
Tip
• You can change the channel levels at any time by
using CHANNEL +/– on the front panel or from the
remote control receiver menu (see Basic remote
control displays on page 33 for more on this). You can
set separate levels for each listening mode
(Standard/Home THX, Advanced Cinema/Advanced
Concert and Stereo) as well as for SB CH ON.
However, these settings will be cleared if you use the
Surround Setup or Auto Surround Sound Setup to set
the channel levels at a later date.
60
En
The Surround Setup menu
Speaker Distance
07
5
For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
1
Tip
• For best surround sound, make sure the surround
back speakers are the same distance.
Select ‘Speaker Distance’ then press ENTER.
2.Surround Setup
[ Check ]
[
[
[
[
[
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
[Return]
2 Choose a unit of measurement and press ENTER.
Speaker distance can be expressed in either feet or
meters.
2.3. Speaker Distance
Unit
[Manual]
[Auto]
[Return]
feet
Your Speaker Systems
Normal Surround ”
Select ‘Return’ then press ENTER to finish.
Acoustic Calibration EQ
Acoustic Calibration Equalization is a kind of room
equalizer for your speakers (excluding the subwoofer). It
works by measuring the acoustic characteristics of your
room and neutralizing the ambient characteristics that
can color the original source material. You can also make
these settings manually to get a frequency balance that
suits your tastes. A more advanced setup is also
available, where you can make detailed settings
according to your room’s reverb characteristics (see
Professional Acoustic Calibration EQ on page 63). You
should have the mic connected when using any of the
setup options.
Setting the Acoustic Calibration EQ automatically
1
Select ‘Acoustic Cal EQ’ then press ENTER.
2.Surround Setup
3
Select a setup option and press ENTER.
[ Check ]
[Manual]
[Auto]
[
[
[
[
[
[Return]
[Return]
2.3. Speaker Distance
Your Speaker Systems
Normal Surround ”
2
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
Select ‘Auto’ then press ENTER.
2. 4. Acoustic Cal EQ
[Data Copy]
[Manual]
CUSTOM1 , CUSTOM2
[Auto]
ALL ADJ & FRONT ALIGN
• Manual – Select each speaker in turn and adjust the
distance manually.
• Auto – The speaker distances are set automatically
by the receiver as it outputs test tones. (For this setup
you must have the mic connected.)
4 If you selected ‘Auto’, select ‘Start’ and press
ENTER. If you selected ‘Manual’, adjust the distance
of each speaker using the / (cursor left/right)
hard keys.
Using the Manual setup, you can adjust the distance of
each speaker in 0.2 feet (0.05 meter) increments.
With the Auto setup, !! Complete !! is displayed onscreen after the speaker distances are set. If you want to
check the settings, select Check and press ENTER.
[Professional]
[Return]
As the receiver outputs test tones, the frequency balance
is adjusted automatically for the following settings:
• ALL CH ADJ – All the speakers are set individually so
no special weighting is given to any one channel.
• FRONT CH ALIGN – All speakers are set in
accordance with the front speaker settings.
!! Complete !! is displayed on-screen after the acoustic
calibration equalization is set. If you want to check the
settings, select Check and press ENTER.
3
Select ‘Return’ then press ENTER to finish.
61
En
The Surround Setup menu
07
Setting the Acoustic Calibration EQ manually
Tip
Before manually adjusting the Acoustic Calibration EQ,
we recommend copying the ALL CH ADJ or the FRONT
CH ALIGN settings from the Auto setup above (or from
Introduction to home theater on page 39) to one of the
custom settings. Instead of just a flat EQ curve, this will
give you a reference point from which to start (see
Copying your Acoustic Calibration EQ settings below for
how to do this).
1
• Changing the frequency curve of one channel too
drastically will affect the overall balance. If the
speaker balance seems uneven, you can raise or
lower channel levels using test tones with the TRIM
feature. Use (cursor right) to move to the far right
side of the OSD, then use / (cursor up/down) to
raise or lower the channel level for the current
speaker.
Select ‘Acoustic Cal EQ’ then press ENTER.
2.Surround Setup
5 When you’re done, press (cursor down) to
select ‘Return’ then press ENTER to finish.
[ Check ]
[
[
[
[
[
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
Note
• If the message OVER !! appears on-screen, it means
the frequency curve may result in distortion from the
speaker. Adjust the frequency curve accordingly.
[Return]
2
Select ‘Manual’ then press ENTER.
Copying your Acoustic Calibration EQ settings
2. 4. Acoustic Cal EQ
[Data Copy]
[Manual]
CUSTOM1 , CUSTOM2
[Auto]
ALL ADJ & FRONT ALIGN
[Professional]
[Return]
3
Select CUSTOM1 or CUSTOM2 then press ENTER.
If you want to manually adjust the Acoustic Calibration
EQ (see Setting the Acoustic Calibration EQ manually
above), we recommend copying the ALL CH ADJ or the
FRONT CH ALIGN settings from the Auto setup above
(or from Introduction to home theater on page 39) to one
of the custom settings. Instead of just a flat EQ curve, this
will give you a reference point from which to start.
1
2.4. Acoustic Cal EQ
Manual
Select ‘Acoustic Cal EQ’ then press ENTER.
2.Surround Setup
[ Check ]
[ CUSTOM1 ]
A[ CUSTOM2 ]
[
[
[
[
[
[Return]
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
[Return]
4 Select the channel you want, adjust the
frequency curve to your liking, then move to the
next speaker.
2.4. Acoustic Cal EQ
Manual
Target Curve : CUSTOM1
Channel [L•SMALL]
2
Select ‘Data Copy’ then press ENTER.
2. 4. Acoustic Cal EQ
[Data Copy]
[Manual]
CUSTOM1 , CUSTOM2
[Auto]
ALL ADJ & FRONT ALIGN
[Professional]
63
125
250
500
1k
2k
4k
8k
16k
[Return]
TRIM
[Return]
Use the / (cursor left/right) hard keys to select the
channel, then ENTER to select it.
Use the / (cursor left/right) hard keys to select the
frequency and / (cursor up/down) to boost or cut the
EQ. When you’re finished, press ENTER to move to the
next channel.
62
En
The Surround Setup menu
3 Select CUSTOM1 or CUSTOM2 then use the /
(cursor left/right) hard keys to select the setting you
want to copy.
2.4. Acoustic Cal EQ
Manual
2.4. Acoustic Cal EQ
A.Cal EQ Data Copy
[ CUSTOM1 ]
A[ CUSTOM2 ]
[Return]
To
←
From
CUSTOM1
[ ALL ADJ ]
CUSTOM2
[CUSTOM2 ]
[Copy OK]
[Cancel]
• You can also copy from one custom setting to
another. For more on the ALL CH ADJ and FRONT CH
ALIGN settings, see Setting the Acoustic Calibration
EQ automatically above.
4 Select ‘Copy OK’ and press ENTER to confirm.
You will be taken to the Acoustic Calibration EQ settings
menu. Select Return then press ENTER to go back to the
Surround Setup menu.
Professional Acoustic Calibration EQ
This setup minimizes the unwanted effects of room
reverberation by calibrating your system based on the
direct sound coming from the speakers. It can also
provide you with a graphical output of the frequency
response of your room.
07
By analyzing the graph, you should be able to see how
your room is responding to certain frequencies.
Differences in channel level and speaker distance are
taken into account automatically (compensation is
provided for comparison purposes), but the frequency
measurements are always shown without the
equalization performed by this receiver.
Note that due to an effect known as ‘group delay’, lower
frequencies will take longer to be generated than higher
frequencies (this is most obvious when comparing the
frequencies at 0ms). This initial slope is not a problem
(i.e. excessive reverb) with your listening room.
Setting Professional Acoustic Calibration EQ
according to your room characteristics
Using the manual setup, you can set the time period at
which the frequency response is analyzed for calibration.
You can pinpoint the time that is best for calibration of
the system for your particular room characteristics. The
graph below shows the difference between standard
acoustic calibration and professional calibration (the
gray circles represent the point at which the microphone
captures the sound for frequency analysis).
Level
Test tone
Acoustic Cal. EQ Pro
calibration range
Note
• Before setting up with Professional Acoustic
Calibration EQ, you should finish calibrating using
the Auto Surround Setup on page 39.
How to use Professional Acoustic Calibration EQ
If you find that lower frequencies seem overly reverberant
in your listening room (i.e. it sounds ‘boomy’), or that
different channels seem to exhibit different reverb
characteristics, use the auto pro setup to calibrate the
room automatically. This should provide a more balanced
calibration than simply using the standard Acoustic
Calibration EQ. The manual setup allows you to
customize your system calibration with the help of a
graphical output that can be displayed on-screen, or
using a computer (with software available from
Pioneer—see Connecting a PC for Advanced MCACC
output on page 88 for more on this).
0
80
Standard Acoustic Cal.
EQ calibration range
160
As soon as audio is output from your speaker system, it
is influenced by room characteristics, such as walls,
furniture, and the dimensions of the room. The sooner
the frequency analysis, the less it is influenced by the
room. We recommend an earlier time setting of 20–40ms
to compensate for two major factors that will influence
the sound of most rooms:
• Reverberance of high vs. low frequencies –
Depending on your room, you may find that lower
frequencies seem overly reverberant compared to
higher frequencies (i.e. your room sounds ‘boomy’).
This may result in a skewed frequency analysis if the
measurement is done too late.
Low
frequencies
Level
High
frequencies
How to interpret the graphical output
The graph shows decibels on the vertical axis and time
(in milliseconds) on the horizontal axis. A straight line
indicates a flat-response room (no reverb), whereas a
sloping line indicates the presence of reverberation when
outputting test tones. The sloping line will eventually
flatten out when the reverberant sound stabilizes (this
usually takes about 100ms or so).
Time
(in msec.)
Acoustic Cal. EQ Pro
calibration range
0
80
Standard Acoustic Cal.
EQ calibration range
160
Time
(in msec.)
63
En
The Surround Setup menu
07
• Reverb characteristics for different channels –
Reverb characteristics can be somewhat different for
each channel. Since this difference increases as the
sound is influenced by the various room
characteristics, it is often better to capture a
frequency analysis early on for smoother mixing of
channel frequencies/sounds.
• Auto Pro. – The receiver automatically sets an early
time period (20–40 ms or 60–80 ms) for reverb
measurement, giving you a system calibration based
on the direct sound coming from the speakers. The
frequency balance for each channel is then adjusted
to minimize the effect of the room characteristics on
the overall sound.
• Manual Pro. – You can set an early time period for
reverb measurement manually, giving you the
flexibility to choose the direct sound calibration that
works best with your listening area. After you have
made this setting, the frequency balance for each
channel is adjusted automatically, calibrating your
system according to your custom setting.
Left
surround
Level
Right
Surround
Acoustic Cal. EQ Pro
calibration range
0
Standard Acoustic Cal.
EQ calibration range
80
160
Time
(in msec.)
If your room isn’t affected by the factors above, it is often
not necessary to make a 20–40ms setting. Later time
settings may provide a more detailed sound experience
with your speaker system. It is best to try and see what
works best for your particular room.
4 If you selected ‘Auto Pro.’, select ‘Start’ and press
ENTER.
2.4. Acoustic Cal EQ Pro.
Auto Pro
•Connect microphone
•Please be quiet
•Move obstacles away
•If you have a subwoofer
turn power on and
turn volume up
Note that changing the room (for example, moving
furniture or paintings) will affect the calibration results.
In such cases, you should recalibrate your system.
Using Professional Acoustic Calibration EQ
1
Select ‘Acoustic Cal EQ’ then press ENTER.
2.Surround Setup
[ Check ]
[
[
[
[
[
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
[Return]
2
Select ‘Professional’ then press ENTER.
2. 4. Acoustic Cal EQ
[Data Copy]
[Manual]
CUSTOM1 , CUSTOM2
[Auto]
ALL ADJ & FRONT ALIGN
[Professional]
[Return]
3
Select a setup option and press ENTER.
2.4. Acoustic Cal EQ Pro.
” Professional ”
[Auto Pro. ]
Acou. Cal EQ Setup
[Manual Pro. ]al Surround
Reverb Measurement
Reverb View
Advanced EQ Setup
[Return]
64
En
[Start]
[Cancel]
!! Complete !! is displayed on-screen after the acoustic
calibration equalization is set. Select Return to return to
the professional acoustic calibration equalization menu.
5
Select a manual setup option and press ENTER.
2.4. Acoustic Cal EQ Pro.
Manual Pro.
[ Reverb Measurement ]
[ Reverb View ]
[ Advanced EQ Setup ]
[Return]
• Reverb Measurement – Use this to measure the
reverb characteristics of your room for separate
channels in select frequency ranges.
• Reverb View (Normal) – You can check the reverb
measurements made for specified frequency ranges
in each channel. PC Output will also show as an
option after you’ve completed the reverb
measurement. See Connecting a PC for Advanced
MCACC output on page 88 for more on this option.
• Advanced EQ Setup – Use this to select the time
period that will be used for frequency adjustment and
calibration, based on the reverb measurement of
your listening area. Note that using this setup will
alter the settings you made in Automatically setting
up for surround sound on page 39.
The Surround Setup menu
6 If you selected ‘Reverb Measurement’, select
‘Start’ and press ENTER.
2.4. Acoustic Cal EQ Pro.
Reverb
•Connect microphone
•Please be quiet
•Move obstacles away
•If you have a subwoofer
turn power on and
turn volume up
[Start]
[Cancel]
07
You can switch between your connected speakers
(excluding the subwoofer), and display the
measurements for the following frequencies: 63Hz, 125
Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz and 16kHz.
Select the setting from the following time periods (in
milliseconds): 0–20ms, 10–30ms, 20–40ms, 30–50ms,
40–60ms, 50–70ms and 60–80ms. This setting will be
applied to all channels during calibration.
When you’re finished, select Go. It will take about 2–11
minutes for the calibration to finish.
!! Complete !! is displayed on screen when the reverb
measurement is finished (this may take 2–6 minutes).
You can select Reverb View (above) to see the results
on-screen. See Connecting a PC for Advanced MCACC
output on page 88 for more on setting up your computer
for the graphical output.
7 If you selected ‘Reverb View’, you can use the
cursor buttons (hard keys) to check the reverb
characteristics for each channel. Select ‘Return’ and
press ENTER when you’re done.
2.4. Acoustic Cal EQ Pro.
Reverb View
[ C ]
dB
[ 500Hz ]
!! Complete !! is displayed on-screen after the acoustic
calibration equalization is set. If you want to check the
settings, select Check and press ENTER.
X-Curve
Most soundtracks mixed for cinema sound too bright
when played back in large rooms. The X-Curve setting
acts as a kind of re-equalization for home theater
listening, and restores proper tonal balance of movie
soundtracks.
1
Select ‘X-Curve’ then press ENTER.
2. Surround Setup
[ Check ]
0
80
[
[
[
[
[
160ms
[Return]
Use the / (cursor left/right) buttons to select the
channel and the frequency you want to check. Use the
/ (cursor up/down) buttons to go back and forth
between the two. Note that the markers on the vertical
axis indicate decibels in 2dB steps.
1.
2.
3.
4.
5.
Speaker Systems ]
Channel Level ]
Speaker Distance ]
Acoustic Cal EQ ]
X-Curve ]
[ Return ]
2 Use the / (cursor left/right) hard keys to
switch the X-Curve ON or OFF.
2. 5. X-Curve
8 If you selected ‘Advanced EQ Setup’, input the
time setting you want to use for calibration, then
select ‘Go’. Select ‘Start’ from the next screen.
Based on the reverb measurement above, you can
manually choose the time period that will be used for the
final frequency adjustment and calibration. Even though
you can make this setting without reverb measurement,
it is best to use the measurement results as a reference
for your time setting. For an optimal system calibration
based on the direct sound coming from the speakers, we
recommend using the 20–40ms setting.
X-Curve
[ ON ]
[ Manual ]
[ Semi Auto ]
[ Return ]
Your X-Curve
" –0.5dB/oct
"
If you select OFF, the frequency curve will be flat and you
won’t be able to adjust the X-Curve.
3
Select a setup option and press ENTER.
2. 5. X-Curve
2.4. Acoustic Cal EQ Pro.
dB
[ C ]
[ 500Hz ]
X-Curve
[ ON ]
[ Manual ]
[ Semi Auto ]
[ Return ]
0
80
160ms
[20~40ms]
[Go]
[Return]
Use the / (cursor left/right) buttons to select the
channel, frequency, and time setting. Use the /
(cursor up/down) buttons to switch between them.
Your X-Curve
" –0.5dB/oct
"
• Manual – Adjust the X-Curve manually.
65
En
The Surround Setup menu
07
• Semi Auto – The X-Curve is calculated automatically.
The larger your listening area (as determined by the
speaker distance setting), the greater the X-Curve
slope (see the following step for more on this).
4 Check the X-Curve setting. If you selected
‘Manual’, make any adjustments necessary to the XCurve.
2.5. X-Curve Manual
63
12
25
50
1k
2k
4k
8k
16
X-Curve
[ –2.0dB/oct ]
[ Return ]
Use the / (cursor left/right) hard keys to adjust the
setting. The X-Curve is expressed as a downwards slope
in decibels per octave, starting at 2kHz. The sound
becomes less bright as the slope increases (to a
maximum of -3.0dB/oct). Use the following guidelines to
set the X-Curve according to your room size:
Room size (m2)
≤36
≤48
≤60
≤72
≤300 ≤1000
X-Curve (dB/oct) –0.5
–1
–1.5
–2
–2.5
5
–3
Select ‘Return’ then press ENTER to finish.
Note
• Since the principal is the same, X-Curve isn’t applied
when you’re using any of the Home THX modes (see
Using the Home THX modes on page 45).
Checking your surround settings
You can check through the receiver settings screen by
screen after you’re finished using the Surround Setup.
1 Select ‘Check’ from the Surround Setup menu
and press ENTER.
2.Surround Setup
[ Check ]
[
[
[
[
[
1.Speaker Systems ]
2.Channel Level ]
3.Speaker Distance ]
4.Acoustic Cal EQ ]
5.X-Curve ]
[Return]
2 Use the / (cursor left/right) hard keys to
cycle through the settings screen by screen.
These appear in the same order as the Surround Setup
menu. Select Return then press ENTER to go back to the
Surround Setup menu.
66
En
Controlling other equipment
08
Chapter 8
Controlling other equipment
Using the remote control with other
components
The supplied remote control can operate not only this
receiver, but also your TV, DVD player and other
components. If the component is listed in the remote
control's memory, simply follow the steps in Recalling
preset codes below. If the component is not listed, or if
you want the remote to learn additional operations, see
Programming signals from other remote controls on
page 69.
Recalling preset codes
The following steps show you how to recall preset codes
for each input source. Use the remote control touch
screen to do this.
1 Make sure the component you want to control is
switched on.
2
Press PRESET RECALL on the remote setup menu.
SETUP
1/3
CALIBRATE
Note
PRESET RECALL
• The remote control operations in this section are
accessed from the remote setup menu. To go to the
remote setup menu, press
from the remote
SETUP
control Home menu (
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
3
DVR
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
LEARNING
MULTI OPERATION
DIRECT FUNCTION
):
SETUP
1/3
CALIBRATE
PRESET RECALL
LEARNING
3 From the ‘Select Function’ screen, choose the
input function which matches the connection for the
component you want to control.
For example, press DVD/LD if you want to control the
DVD player that you connected to the DVD/LD terminals.
MULTI OPERATION
DIRECT FUNCTION
Select Function
PRESET RECALL
SETUP
DVD/LD
• For more on navigating the remote control menu
screens, see Basic remote control displays on
page 33. See also TV control menu screens on page 36
and Operating menus for additional components on
page 37.
• When using a TV, it is often best to use the TV/DVD
input for the TV source, and TV CONT for the TV
screen or monitor.
TV/DVD
SAT
CANCEL
• Use the / (cursor up/down) buttons to scroll
through the component options.
• You can select any button, but choosing a button
that’s already assigned will overwrite the old preset
(and any other operations you may have
programmed).
67
En
08
Controlling other equipment
4 From the ‘Replacing Device’ screen choose the
type of component that you’ve connected.
In this example, we’re setting the remote to control a
DVD player, so we’ll select DVD.
7 Point the remote at the component and press
TRY to test if you've set it up properly.
If the component you are trying to control turns on/off,
the setup for this component is complete and you can go
to step 8.
Replacing Device
PRESET RECALL
Following Setting?
PRESET RECALL
DVD
device : DVD
TV
maker :
Pioneer
DVD recorder
type :
Pioneer-1
CANCEL
• It is best to have the input source button (DVD/LD)
match the component.
5 From the ‘Setting Makers’ screen, select the
name of the company that makes your component.
Use the / (cursor up/down) buttons to scroll through
the available manufacturers. Here we’ll select PIONEER
as an example.
Setting Makers
PRESET RECALL
Pioneer
AKAI
DENON
BACK
CANCEL
6 Select a setting type.
There may be only one option listed, or there may be
several. Start with the first button available, which will
show the makers name and 1 (in this case Pioneer-1).
Setting Type
INSTALL
TRY
BACK
CANCEL
If the component doesn’t respond, it’s possible that:
• Your component manufacturer has several preset
codes for the same component. Press BACK to go
back and select another number (if there is one) from
the list.
• Your component doesn't have a standby mode (and
therefore won’t switch on/off).
• There is something blocking the path between the
remote control and the remote sensor of the
component you’re trying to control.
• The preset code is unavailable for your component.
Press CANCEL to exit, then try using the method
described in Programming signals from other remote
controls below to program the component into the
remote control. If your component type is different
from the set of controls associated with the input
source (for example you want to control an LD with
the DVD/LD button), it is useful to choose INSTALL
in the next step to change the screen to control the
component you’ve connected.
8 Press INSTALL to confirm and go back to the
‘Select Function’ screen to control another
component.
PRESET RECALL
Pioneer-1
Pioneer-2
Following Setting?
PRESET RECALL
device : DVD
maker :
Pioneer
type :
Pioneer-1
BACK
CANCEL
INSTALL
TRY
BACK
CANCEL
PLEASE WAIT
From the Select Function screen (step 3), you can press
to exit and return to the remote control Home menu
screen.
68
En
Controlling other equipment
To exit without saving the preset you have assigned,
press CANCEL instead of INSTALL above.
Tip
• Pioneer DVD recorders fall into the following setting
types:
Pioneer-1 – DVR-7000
08
• Use the / (cursor up/down) buttons to scroll
through the component options (the RECEIVER and
TUNER screens are not available).
3 On the touch screen, press the button that
corresponds to the command you want to teach the
remote control.
For example, choose the (play) button to program this
remote control to start playback on your DVD player.
Pioneer-2–4 – DVR-310, DVR-510H
Pioneer-5 – DVR-57H, DVR-810H
LEARN
DVD
If you have more than one Pioneer DVD recorder of
setting type 2–4, you can select different setting types
for each (allowing for separate control).
DVD
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code in Recalling preset codes above.
Press LEARNING on the remote setup menu.
SETUP
1/3
CALIBRATE
PRESET RECALL
LEARNING
MULTI OPERATION
DIRECT FUNCTION
2 From the ‘Select Function’ screen, choose the
input function which matches the connection for the
component you want to control.
For example, press DVD/LD if you want to program
signals for the DVD player that you connected to the
DVD/LD terminals.
END
LEARN
1/2
DVD
TV
CONT
AUDIO
SUBTITLE
DISPLAY
TOP MENU
2/2
TV
CONT
DVD
1
2
3
CLR
4
5
6
+10
7
8
9
0
SEARCH
MODE
RETURN
A remote icon shows in the top right corner of the touch
screen after you’ve selected a button (you can deselect it
by pressing it again).
• Remote control soft keys such as
,
, /
(cursor left/right) and TV CONT are used to select
menu screens (even in learning mode), so therefore
cannot be programmed.
• The Learn and L buttons that appear on some
component screens are unassigned buttons which
can be used to learn new commands. See Editing
remote control button names on page 70 to change
the name once you’ve programmed a command.
• You can program the remote control hard keys
(VOLUME +/– and MUTE are only available with TV
CONTROL), but the command will remain the same
for all screens of the component selected.
• Press END to go back without making any changes.
4 While the icon is displayed, point the two
remote controls toward each other and press the
button on the other remote control corresponding
to the operation you want to program.
REMOTE CONTROL UNIT
DIGITAL MULTI PROCESSING AMPLIFIER
SELECT
ENTER
TV/VCR
FUNCTION
MUTE
MENU
ATT
9
SIGNAL
6
TV FUNC
0
3
8
VOLUME
DISC
5
2
TV
TV CONTROL
7
4
1
+10
TV VOL
CLASS
Î
GUIDE
VCR2
TV/VCR
RECEIVER
OFF
3
7
- CHANNEL +
¢
4
- STATION +
VCR1
TUNER
SYSTEM
MULTI
SWAP
TV/SAT
MD/TAPE
OPERATION
CD
8
¶
- SUB CH +
¡
1
- TUNING +
SETUP
DSP
SYSTEM
P IN P
THX
DVD/LD
CHANNEL LEVEL
ENTER
EFFECT LEVEL
CH SEL
CANCEL
SETUP
VOLUME
SAT
STEREO
MUTE
TV/DVD
EFFECT
ENTER
AV AMPLIFIER
DVD/LD
REMOTE
MENU
SYSTEM
SETUP
LEARNING
DTV MENU
CHANNEL
Select Function
S0URCE
1
END
12 – 30 cm
(5–12 inches)
When the command has been learned, OK! shows on
the remote control touch screen and the remote control
returns to the command learning screen (step 3). Repeat
steps 3 and 4 to program additional commands.
If you want to learn signals for additional components,
press END to go back to the Select Function screen and
start again from step 2.
69
En
08
Controlling other equipment
Note
• If you see Failed (or OK! doesn’t appear) on the
touch panel, or OK! is displayed, but you find that the
command wasn't learned, try teaching the command
again, but vary the distance (closer or farther)
between the remote controls. Some signals may be
stronger than others and require more distance (a
projector’s remote signal, for example).
2 Choose the setting of an input by pressing the
ON/OFF button on the touch screen.
Each press switches between ON and OFF.
DIRECT FUNCTION
DVD/LD : ON
TV/DVD : ON
SAT : ON
• There may be certain remote signals that can’t be
programmed correctly.
OK
• The remote control has a limited memory. If you see
Memory Full appear in the display, use the PRESET
RECALL feature in Recalling preset codes on page 67
to overwrite any programmed buttons that you aren’t
using. This will free up memory to program additional
remote signals.
• Use the / (cursor up/down) buttons to scroll
through the component options.
3
Press OK to confirm the settings.
Remote Direct function
• Default setting: All inputs – ON
On the default setting, when you press an input select
button (DVD/LD, DVR/VCR1, etc.), both the receiver
input source and the remote control change to the
selected function.
When an input select button is set to OFF, pressing that
button changes the function of the remote control only.
This can be useful when you want to operate one
component without interrupting playback of another.
1 Press DIRECT FUNCTION on the remote setup
menu.
Editing remote control button names
You can rename the buttons on the remote control menu
screens for different input sources (such as DVD/LD or
SAT). You may want to do this if you taught the remote
control a new command in Programming signals from
other remote controls above, but the command doesn’t
correspond with the button name.
1
Press KEY LABEL on the remote setup menu.
SETUP
2/3
CLOCK DISPLAY : AM/PM
CLOCK SETTING
SETUP
1/3
CALIBRATE
PRESET RECALL
LEARNING
BEEP :
TIMEOUT
KEY LABEL
MULTI OPERATION
DIRECT FUNCTION
2 From the ‘Select Function’ screen, select the input
source menu that contains the button you want to
rename.
For example, press DVD/LD if you taught the DVD/LD
remote screen a new command from your DVD player.
Select Function
KEY LABEL
DVD/LD
TV/DVD
SAT
CANCEL
70
En
Controlling other equipment
3 Select the button you want to rename.
For example, choose the SEARCH MODE button if it was
programmed with the ‘eject’ command from your DVD
player’s remote.
08
5 Edit the button as necessary.
If you selected the text input method:
DVD/LD
KEY LABEL
KEY LABEL
END
DVD
1
A B C D E F G H I
TV
CONT
DVD
2
3
J K L M N O P Q R
CLR
S T U V W X Y Z
4
5
6
+10
7
8
9
0
SPACE
SEARCH
MODE
CLEAR
OK
RETURN
• Use the letter and number buttons to spell out the
name you want.
• Remote control soft keys such as
,
, /
(cursor left/right) and TV CONT are used to select
menu screens (even in learning mode), so therefore
cannot be renamed.
• Press END to go back without making any changes.
4 Choose how you want to change the look of the
button.
• Press SPACE to add a space in the name.
• Press CLEAR to delete characters one at a time.
• Press (small text only) to go to the next line.
• Use the / (cursor left/right) soft keys to go
forward/back a screen.
If you selected the graphic input method:
DVD / LD
KEY LABEL
DVD / LD
KEY LABEL
SEARCH
MODE
SELECT LABEL TYPE
TEXT : LARGE
TEXT : SMALL
CLEAR
OK
GRAPHIC
Select one of the following options:
• TEXT : LARGE – Select this if you want to input a
short name, such as EJECT.
• TEXT : SMALL – Select this if the name is fairly long,
for example, DVD Tray Eject.
• GRAPHIC – Select this if you want to replace the
button name with an icon, such as .
• Use the icon buttons to select a graphic.
• Press CLEAR to return to the original button
appearance.
• Press
to go back without editing the button.
6 Press OK when you’ve finished.
PLEASE WAIT shows in the remote display while the
name or graphic is input and you’ll return to step 3.
Note
• With power buttons, you won’t be able to delete the
‘’ graphic. These buttons are best left for switching
the component on or off.
• After confirming, you won’t be able to return to the
original button appearance without resetting the
remote control (as described on page 11).
71
En
08
Controlling other equipment
Multi Operation and System Off
The Multi Operation feature allows you to program a
series of commands for the components in your system.
For example, you could turn on your TV, turn on your DVD
player and start playing the loaded DVD using only two
buttons on the remote control.
If you are programming a shutdown (system off)
sequence, select RECEIVER from the end of the list.
Select Function
MULTI OPERATION
DVD/LD
Similar to multi operations, System Off allows you to use
one button to stop and switch off a series of components
in your system at the same time.
TV/DVD
SAT
CANCEL
Note
• Before Multi Operation and System Off will work
correctly, you must setup the remote to work with
your TV and other components (see Recalling preset
codes on page 67 and Programming signals from
other remote controls on page 69 for more on this).
• Power on and off commands only work with
components that have a standby mode.
Programming a multi operation or a
shutdown sequence
• Use the / (cursor up/down) buttons to scroll
through the component options.
3 Press ‘Add’ to choose an operation in the
sequence.
If this is the first command in the sequence, the
operation you’re adding will be placed at the top.
Otherwise, the command will simply take the next place
in the sequence.
DVD/LD
1 Press MULTI OPERATION on the remote setup
menu.
SETUP
MULTI OPERATION
1/3
CALIBRATE
PRESET RECALL
Add
Replace
Run
Delete
Delay
OK
LEARNING
MULTI OPERATION
DIRECT FUNCTION
2 From the ‘Select Function’ screen, choose the
input function.
This will be the one that starts the multi operation when
you select it as an input source. For example, press DVD/
LD if the multi operation is being used to switch on the
DVD player connected to the DVD/LD terminals.
4 Choose the component and command you want
to add to the multi operation or shutdown
sequence.
For example, choose DVD/LD from the select function
menu (this now takes the name of the multi-operation
component), then (play) or (stop) from the DVD
menu to start (or stop) playback on your DVD player.
MULTI OPERATION
DVD/LD
MULTI OPERATION
DVD/LD
DVD
DVD
END
1/2
TV
CONT
TV/DVD
SAT
CANCEL
AUDIO
SUBTITLE
DISPLAY
TOP MENU
• Press END to go back without making any changes.
72
En
Controlling other equipment
• You don't need to program the receiver to switch to
the input function selected in step 2, or to switch on
or off. This is done automatically.
08
• To add a new command above another command,
press the existing command before pressing Add.
With Pioneer components, you don’t need to:
• To erase a command, select the operation you want
to erase and press Delete.
• program the power to switch off in a shutdown
sequence;
• Commands will be stored regardless of how you exit
from this screen.
• program the power to switch on if it’s the source
component selected in step 2;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
5 If necessary, add a delay between operations by
pressing ‘Delay’.
Some components may take a few seconds to switch on
or off, or perform certain operations. In these cases, you
may want to add a slight delay (up to sixty seconds is
possible) between commands.
Use the + and – buttons on the Delay Time screen to
adjust the delay time then press OK.
7 Press OK when you’re finished.
PLEASE WAIT shows in the remote display while the
multi operation is stored and you’ll return to step 2.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 From the remote control Home menu
MULTI OPERATION.
1/3
HOME
RECEIVER
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
press
DVD/LD
MULTI OPERATION
Delay Time
SETUP
0.1 sec
–
OK
+
CANCEL
• If you want to change the delay time after it’s been
set, press the delay time, then press SET to come
back to this screen.
6 Repeat steps 3 to 5 for additional commands.
As each command is entered, they will appear in order on
the remote touch screen.
DVD/LD
MULTI OPERATION
2 Press a function button that has been set up with
a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
MULTI OPERATION
Select Function
DVD
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
VCR2
VCR3
CD-R
/ TAPE1
VIDEO
MULTI CH
INPUT
TV
CONT
CANCEL
DVD PLAY
Delay -
2.0sec
Add
Replace
Run
Delete
Delay
OK
• To test the sequence before confirming it, press Run.
• To replace a command in the sequence, select the
command then press Replace. Add the operation as
shown in the steps above.
73
En
08
Controlling other equipment
Using System off
• From the remote control Home menu
press
SYSTEM OFF.
The command sequence you programmed will run, then
all Pioneer components will switch off, followed by this
receiver.
2 Connect the CONTROL OUT jack of that
component to the CONTROL IN jack of another
Pioneer component.
Use a cable with a mono mini-plug on each end for the
connection.
CONTROL
RECEIVER
IN
RECEIVER
INPUT 1
2
OUT
IN
OUT
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
CONTROL
1/3
HOME
VSX-59TXi
CONTROL
SETUP
OUT
S400
(AUDIO)
AUDIO
Switching components on and off
using the 12 volt trigger
You can connect components in your system (such as a
screen or projector) to this receiver so that they switch on
or off using a 12 volt trigger when you select an input
function. However, you must specify which input
functions switch on which trigger(s) using the Expert
Setup menu (see 12 Volt Trigger on page 95 to do this).
Note that this will only work with components that have a
standby mode.
• Connect the 12V TRIGGER jack of this receiver to
the 12V TRIGGER of another component.
Two connections are possible. Use a cable with a mono
mini-plug on each end for each connection.
After you’ve specified the input functions that will switch
on the trigger(s), you’ll be able to switch the component
on or off just by pressing the input function(s) you’ve set
on page 95.
Operating other Pioneer components
with this unit’s sensor
Many Pioneer components have SR CONTROL jacks
which can be used to link components together so that
you can use just the remote sensor of one component.
When you use a remote control, the control signal is
passed along the chain to the appropriate component.
Note that if you use this feature, make sure that you also
have at least one set of analog audio jacks connected to
another component for grounding purposes.
1 Decide which component you want to use the
remote sensor of.
When you want to control any component in the chain,
this is the remote sensor at which you’ll point the
corresponding remote control.
74
En
R
POWER
AMP
IN
L
MONITOR
OUT 1
IN
MULTIROOM &
SOURCE
REMOTE IN
MULTI ROOM &
SOURCE
MONITOR
OUT 2
ANTENNA
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
PB
PR
PR
3 Continue the chain in the same way for as many
components as you have.
Note
• If you want to control all your components using this
receiver’s remote control, refer to Using the remote
control with other components on page 67 and
Programming signals from other remote controls on
page 69.
Using other functions
09
Chapter 9
Using other functions
Making an audio or a video recording
Monitoring your recording
You can make an audio or a video recording from the
built-in tuner, or from an audio or video source
connected to the receiver (such as a CD player or TV).
You can listen to (monitor) the recording as it’s being
made if you’ve connected a cassette deck with a
monitoring function to the TAPE 2 MONITOR jacks on
the rear panel.
Keep in mind you can't make a digital recording from an
analog source or vice-versa, so make sure the
components you are recording to/from are hooked up in
the same way (see Connecting your equipment on
page 14 for more on connections).
You can record using composite and S-video
connections interchangeably, but you won’t be able to
record sources connected to the component video
inputs. See About the video converter on page 22 for more
on this.
• Press TAPE 2 MONITOR to switch between the
recorded signal and the original source signal.
With the remote, you may need to press
Home menu ( ) first before reaching the receiver menu
screen shown below (use the / (cursor left/right)
soft keys to go to the previous/next menu screen).
3/4
RECEIVER
For more information about video connections, see
Connecting a VCR or DVD recorder on page 20 and
Connecting other video sources on page 21.
TV
CONT
RECEIVER
1 Select the source you want to record.
Use the INPUT buttons (or the INPUT SELECTOR dial on
the front panel).
2 Select the input signal (if necessary).
Press SIGNAL SELECT to select the input signal
corresponding to the source component (see Selecting
the input signal type on page 48 for more on this).
on the
RECEIVER
ACOUSTIC
CAL.
INPUT
SB CH
MODE
SPEAKER
A/B
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
3 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component's instruction manual if you're unsure.
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
Tip
• To record the tape 2 monitor signal to a recorder
connected to the CD-R/TAPE 1 inputs, select any
input (except CD-R/TAPE 1) and switch the tape 2
monitor on.
5 Start recording, then start playback of the source
component.
Note
• The receiver's volume, tone (bass, treble, Midnight,
Loudness), and surround effects have no effect on
the recorded signal.
• Some digital sources are copy-protected, and can
only be recorded in analog.
• Some video sources are copy-protected. These
cannot be recorded.
75
En
09
Using other functions
Reducing the level of an analog
signal
ACOUSTIC
CAL.
• From the remote control receiver menu, press
INPUT ATT to switch the input attenuator on or off.
You may need to press RECEIVER on the Home menu ( )
first before reaching the receiver menu screen shown
below (use the / (cursor left/right) soft keys to go to
the previous/next menu screen).
INPUT
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
ON/OFF
L
R
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
2 Use the (OPTION) +/– buttons to adjust the
amount of delay.
The delay can be adjusted from 0.0–6.0 frames (in 0.1
frame steps).
3
Press ENTER to confirm.
Note
• One second is equal to 30 frames of NTSC format
video, and 25 frames of PAL.
TV
CONT
SB CH
MODE
SPEAKER
A/B
OPTION
• When listening to an analog source, you can’t use
sound delay when Stream Direct is on.
3/4
RECEIVER
TONE
VIDEO INPUT
PHONES
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
the that the OVER indicator is lights often, or you can
hear distortion in the sound.
RECEIVER
SB CH
MODE
TUNER
MIDNIGHT
Watching video and audio sources
independently
You can listen to a sound source and select a different
video source on your TV.
• While listening to a source, press VIDEO SELECT
to select the video source you want to watch.
Note
With the remote, you may need to press
• The attenuator isn’t available with digital sources, or
when using Stream Direct modes 2 or 3.
on the
RECEIVER
Home menu ( ) first before reaching the receiver menu
screen shown below (use the / (cursor left/right)
soft keys to go to the previous/next menu screen).
Adjusting the delay of a soundtrack
Some monitors have a slight delay when showing video,
so the soundtrack will be slightly out of sync with the
picture. By adding a bit of delay, you can adjust the sound
to match the presentation of the video.
1 Press OPTION repeatedly until SOUND DELAY
shows in the display.
With the remote, you may need to press
RECEIVER
3/4
RECEIVER
TV
CONT
RECEIVER
on the
INPUT
SB CH
MODE
SPEAKER
A/B
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
Home menu ( ) first before reaching the receiver menu
screen shown below (use the / (cursor left/right)
soft keys to go to the previous/next menu screen).
ACOUSTIC
CAL.
2/4
RECEIVER
76
En
RECEIVER
TV
CONT
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
–
OPTION
+
–
CH LEVEL
+
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
VIDEO INPUT
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
Press repeatedly to cycle through the possible video
sources. You can select DVD/LD, TV, SAT, VIDEO, DVR/
VCR1, VCR2, VCR3 or OFF (no video signal).
Using other functions
09
Note
• If you change the source using the input buttons (or
front panel INPUT SELECTOR dial), the system
returns to normal playback.
Enhancing SACD playback
You can get more detail from SACDs by maximizing the
dynamic range (during digital processing) using the
SACD gain feature.
1 Press OPTION repeatedly until SACD GAIN shows
in the display.
With the remote, you may need to press
on the
RECEIVER
Home menu ( ) first before reaching the receiver menu
screen shown below (use the / (cursor left/right)
soft keys to go to the previous/next menu screen).
Using the A/D converters to give
greater definition to 2-channel sound
This receiver has high-quality 192kHz (24bit) A/D
converters that can be used in parallel to provide greater
resolution of DSP processing with analog 2-channel
sources. There are two ways to get 192kHz A/D
conversion:
1 Switch the SD:1 NORMAL Stream Direct mode
on.
See Using the Stream Direct mode on page 47 for more on
this.
2 Select the STEREO listening mode and switch off
any other sound processing features.
These features include:
• Midnight/Loudness (page 52)
• Digital Noise Reduction (page 53)
• Dynamic Range Control (page 94)
Receiver
ACOUSTIC
CAL.
MIDNIGHT
DIGITAL NR
TONE
LOUDNESS
OPTION
+
–
CH LEVEL
+
–
Also, make sure you also switch the multichannel input
to 2 CHANNEL in Selecting USB and multichannel analog
input channels on page 49.
Dimming the display
You can choose between four brightness for the front
panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
• From the remote control receiver menu, press
DISPLAY DIMMER repeatedly to change the
brightness of the front panel display.
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
2 Use the (OPTION) +/– buttons to switch the SACD
gain between 0dB and 6dB.
For most SACD sources, selecting 6dB will result in high
sound quality and greater detail. The level will be
adjusted automatically for playback at the same volume.
3
Press ENTER to confirm.
Note
• You shouldn’t have any problems using this feature
with most SACD discs, but if the sound distorts, it is
best to switch the gain setting back to 0dB.
You may need to press RECEIVER on the Home menu ( )
first before reaching the receiver menu screen shown
below (use the / (cursor left/right) soft keys to go to
the previous/next menu screen).
RECEIVER
RECEIVER
3/4
TV
CONT
INPUT
SB CH
MODE
SPEAKER
A/B
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
77
En
09
Using other functions
Switching the speaker impedance
Ω
• Default setting: Speaker 6Ω
We recommend using speakers of 6Ω to 16Ω with this
system, but it is possible to switch the impedance setting
if you plan to use speakers with a lower impedance rating
(for example, less than 6Ω).
• With the receiver in standby, press STANDBY/
ON while holding down the OPTION – button.
Checking your system settings
Use the status display screen to check the various
settings you’ve made for features such as sound delay,
digital noise reduction, and high-sampling.
1 From the remote control receiver menu, press
STATUS to check the system settings.
You may need to press RECEIVER on the Home menu ( )
first before reaching the receiver menu screen shown
below (use the / (cursor left/right) soft keys to go to
the previous/next menu screen).
STANDBY/ON
VIDEO
DVD/LD
ON
3/4
RECEIVER
STANDBY
OFF
TV/DVD
SAT
VIDEO
AUDIO
DVR/VCR1
VCR2
VCR3
CD
CD-R/
TAPE1/MD
TUNER
TV
CONT
P
RECEIVER
INPUT SELECTOR
SB CH
MODE
INPUT
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
VIDEO
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
ON/OFF
These appear on both the OSD and the front panel
display.
DIGITAL IN
S-VIDEO
INPUT
ATT
VIDEO
SELECT
MULTI ROOM & SOURCE
CONTROL
VIDEO INPUT
PHONES
SPEAKER
A/B
L
AUDIO
R
SB CH MODE
ACOUS. CAL EQ
DIGITAL NR
MIDNIGHT
LOUDNESS
TONE CONTROL
VIDEO SELECT
DUAL MONO
SOUND DELAY
HI-BIT
HI-SAMPLING
REAL PHANTOM
Each time you do this, you switch between the
impedance settings:
Ω – Use this setting if your speakers are
• Speaker 4Ω
rated lower than 6Ω.
Ω – Use this setting if your speakers are
• Speaker 6Ω
rated 6Ω or more.
Note
Ω above, the Stream Direct
• If you select Speaker 4Ω
setting is fixed at SD:1 NORMAL (see Using the
Stream Direct mode on page 47).
:
:
:
:
:
:
:
:
:
:
:
:
OFF
ALL ADJ
OFF
ON
OFF
OFF
DVD/LD
CH1
0.0frame
OFF
OFF
OFF
The front panel display shows each of the following
settings for two seconds each:
Surround back speaker/
Virtual back speaker
Video select
Acoustic calibration EQ
Dual mono
Digital noise reduction
Sound delay
Midnight
Hi-bit
Loudness
High-sampling
Tone
Real phantom
Note
• If the Stream Direct mode is switched on, some
settings above will show OFF, even though they are
switched on.
2 When you’re finished, press STATUS again to
switch off the display.
78
En
Using other functions
09
Resetting the system
Setting type
Default setting
Page ref.
Use this feature to reset the system to its factory default
settings (see Default receiver settings below).
Tone
BYPASS
page 52
Digital NR
OFF
page 53
Dual mono
CH1
page 53
Speakers Systems
Normal Surround
page 58
Speaker B setting
Second Zone
page 58
1
Switch the receiver into standby.
2 While holding down the front panel DIGITAL NR
button, press and hold STANDBY/ON for about
three seconds.
The display shows RESET?.
3 Press the front panel OPTION + button.
The display shows OK?.
Speakers (front,
All SMALL
center, surround,
surround back) setting
page 59
Subwoofer setting
YES
page 59
Crossover frequency
80Hz
page 59
Channel levels
All 0 dB (no adjustment)
page 60
Speaker distance
settings
All 10 ft.
page 61
Acoustic Calibration
0dB (no calibration)
page 61
X-Curve
OFF (switches to ON after the page 61
Auto Surround Setup)
Default receiver settings
Tape 2 monitor
OFF
page 75
The table below shows the factory default settings. When
you reset the system, the receiver reverts to these
defaults:
Input attenuator
OFF (all inputs)
page 76
Sound delay
0.0 frames
page 76
Setting type
SACD gain
0dB
page 77
Speaker A/B setting
A
page 80
Digital jack
assignment
Digital-1 (coaxial) – DVD/LD page 90
Digital-2 (coaxial) – TV/DVD
Digital-3 (coaxial) – CD
Digital-4 (optical) – SAT
Digital-5 (optical) – DVR/VCR1
Digital-6 (optical) –
CD-R/TAPE1/MD
2 RF (coaxial) – DVD/LD
4 Within 5 seconds, press OPTION –.
The receiver should now be reset.
Note
• This doesn’t affect the presets that you have
programmed into the remote control (see Using the
remote control with other components on page 67).
See Resetting the remote control below to do this.
Default setting
Page ref.
Input
DVD/LD
Master volume
– – – dB (no sound)
Listening mode
STANDARD (video inputs,
multichannel inputs, USB)
STEREO (audio inputs)
page 43
Advanced surround
effect level
90 (5/7CH STEREO)
50 (all other modes)
page 45
Listening mode (w/
headphones)
STEREO
page 46
USB / multichannel
input channel setting
8 channels
page 47
Stream Direct mode
SD:1 NORMAL (ON)
Acoustic Calibration
EQ
OFF (switches to ALL CH ADJ page 48
after the Auto Surround Setup)
Input signal select
AUTO except multichannel
inputs (ANALOG) and USB
(DIGITAL)
page 48
ON (with surround back
speaker(s) connected)
page 50
Surround Back
Channel mode
Component video jack Component1 – DVD/LD
assignment
Component2 – OFF
Component3 – OFF
page 91
Video input
assignment
MULTI IN – OFF
USB – OFF
page 92
Bass Peak Level
OFF (No limit)
page 93
Dynamic range
control
OFF
page 94
OSD overlay
ON
page 94
12 volt trigger
OFF · OFF
page 95
page 47
Virtual Surround Back OFF
mode
page 51
Hi-bit/Hi-sampling
OFF
page 52
Midnight/Loudness
OFF
page 52
THX Ultra2 subwoofer NO
Surround back
speaker position
0–1ft
page 96
page 96
79
En
10
Other connections
Chapter 10
Other connections
Using speaker system B
You can connect a pair of speakers to the B speaker
terminals on the rear panel to listen to stereo playback in
another room, or you can also use these terminals to
hear surround sound when playing DVD-Audio sources.
Once you’ve made these connections, you’ll have to
change the speaker setting in Speaker Systems on
page 58 to specify how you’re using speaker system B.
• SPAB – Sound is output from speaker system A (up
to 5 channels, depending on the source), the two
speakers in speaker system B, and the subwoofer.
The sound from speaker system B will be the same as
the sound from speaker system A (multichannel
sources will be downmixed to 2 channels). The same
signal as speaker A is output from the pre-out
terminals, except for the surround back pre-outs,
which output the same signal as speaker B.
Switching the speaker system
• SP (off) – No sound is output from the speakers. The
same sound is output from the pre-out terminals as
when selecting speaker system A (above).
This unit has three speaker system settings which allow
you to select the speaker system(s) you want to use.
What you will hear depends on the settings you made in
Speaker Systems on page 58. If you selected Normal
Surround for speaker system A, and Second Zone for
speaker system B, sound is output according to the
explanations below.
• Use the SPEAKER A/B button on the remote
control receiver menu screen to select a speaker
system setting.
You can also use the SP SYSTEM A/B button on the front
panel.
TV
CONT
RECEIVER
ACOUSTIC
CAL.
INPUT
SB CH
MODE
SPEAKER
A/B
INPUT
ATT
VIDEO
SELECT
DISPLAY
DIMMER
TAPE2
MONITOR
STATUS
Using speaker system B in another room
Connect a pair of speakers to the speaker B terminals on
the rear panel the same way you connected your
speakers in Connecting the speakers on page 26. Make
sure to review Placing the speakers on page 27 when
placing the speakers in another room.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
DIGITAL NR
CLASS
• Depending on the settings in Speaker Systems on
page 58 and Using the Stream Direct mode on
page 47, output from the surround back pre-out
terminals may change.
• All speaker systems are switched off when
headphones are connected.
3/4
RECEIVER
Note
• The subwoofer output depends on the settings you
made in Speaker Systems on page 58. However, if
SPB is selected above, no sound is heard from the
subwoofer (the LFE channel is not downmixed).
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
L
R
We recommend using speakers with a nominal
impedance between 6–16Ω (please see Switching the
speaker impedance on page 78 if you plan to use speakers
with a lower impedance).
VIDEO INPUT
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
AUDIO
Press repeatedly to cycle through the speaker system
options:
• SPA – Sound is output from speaker system A and
the same signal is output from the pre-out terminals.
• SPB – Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will be downmixed to these two speakers.
The same signal is output from the surround back
channel pre-out terminals.
80
En
Alternating surround speaker setups using
speaker system B (ITU-R)
After you connect an alternate set of surround speakers,
you can use speaker system B to provide surround sound
when listening to sources like DVD-Audio discs. This will
give you a setup of 9 speakers where the front and center
speakers can be used with normal 7.1 surround (speaker
system A), or 5.1 surround with DVD-Audio sources
(speaker system B in ITU-R setting).
Other connections
1 Connect an alternate (ITU-R) set of surround
speakers as shown below.
Connect the ITU-R surround left speaker to the left
speaker terminal of speaker system B. Connect the ITU-R
surround right speaker in the same way.
A
10
• SPB: ITU-R – ITU-R surround setup for DVD-Audio
and other multichannel music sources. See Speaker
system setup for DVD-Audio/multichannel music
sources on page 98 for more on this.
ITU-R surround
left speaker
L
FRONT
R
CENTER
L
SURROUND
ITU-R surround
right speaker
R
B
L
(Single)
L
• SPOFF– No sound is output from the speakers.
SURROUND
BACK
R
R
• Make sure that the + / – connections are properly
inserted.
2 Select the ‘ITU-R’ setting from the Speaker
Systems menu.
See Speaker Systems on page 58 to specify how you’re
using speaker system B. Normal Surround should be
selected to make this setting.
3 Use the SPEAKER A/B button on the remote
control receiver menu screen to select a speaker
system setting.
You can also use the SP SYSTEM A/B button on the front
panel.
Choose between the following settings (the shaded
boxes indicate the active speakers in each setup):
• SPA: Normal – Normal surround (for movies, etc.)
Note
• Depending on the Stream Direct mode, the surround
channel signal(s) will be output from either the
surround, or surround back channel pre-outs when
SPB: ITU-R is selected.
Bi-amping your front speakers
Bi-amping is when you connect the high frequency driver
and low frequency driver of your speakers to different
amplifiers (in this case, to both front and surround back
terminals) for better crossover performance. Your
speakers must be bi-ampable to do this (having separate
terminals for high and low) and the sound improvement
will depend on the kind of speakers you’re using.
1 Connect your speakers as shown below.
This illustration below shows the connections for biamping your front left speaker. Hook up your front right
speaker in the same way.
A
L
FRONT
Front left
speaker
R
CENTER
L
Hi
SURROUND
R
B
L
(Single)
L
Lo
SURROUND
BACK
R
R
Since both front and surround back speaker terminals
output the same audio, it doesn’t matter which set (front
or surround back) is powering which part (Hi or Low) of
the speaker.
• Make sure that the + / – connections are properly
inserted.
81
En
10
Other connections
2 Select the ‘Front Bi-Amp’ setting from the
Speaker Systems menu.
See Speaker Systems on page 58 to specify how you’re
using the surround back speaker terminals.
Note
• For 7.1 surround sound with this configuration, you
must connect an additional amplifier to the surround
back channel pre-outs. See Connecting additional
amplifiers on page 82 for more on this.
Caution
• Most speakers with both Hi and Low terminals have
two metal plates that connect the Hi to the Low
terminals. These must be removed when you are biamping the speakers or you could severely damage
the amplifier. See your speaker manual for more
information.
• If your speakers have a removable crossover network,
make sure you do not remove it for bi-amping. Doing
so may damage your speakers.
Adding a second set of surround
speakers for Bi-Surround
If your listening area is quite long, and you are seated far
from the front speakers, you may want to add an extra set
of left and right surround speakers instead of your
surround back speakers. These should be placed
between the front speakers and your existing surround
speakers (which should already be placed on either side
of your listening position).
1 Connect a second set of surround speakers as
shown below.
Connect the second surround left speaker to the
surround back left speaker terminal. Connect the second
surround right speaker in the same way.
A
2nd surround
left speaker
L
FRONT
R
CENTER
L
SURROUND
2nd surround
right speaker
R
B
Bi-wiring your speakers
The reasons for bi-wiring are basically the same as biamping, but additionally, interference effects within the
wire could be reduced, producing better sound. Again, to
do this your speakers must be bi-wireable (that is they
must have separate terminals for the high and low
frequencies). When bi-wiring, make sure you’ve selected
Normal Surround in Speaker Systems on page 58.
• To bi-wire a speaker, connect two speaker cords
to each speaker terminal on the receiver.
L
(Single)
L
SURROUND
BACK
R
R
• Make sure that the + / – connections are properly
inserted.
2 Select the ‘Bi-Surround’ setting from the Speaker
Systems menu.
See Speaker Systems on page 58 to specify how you’re
using the surround back speaker terminals.
Using the pre-outs
Connecting additional amplifiers
Caution
• Make sure you use a parallel (not series, which are
fairly uncommon) connection when bi-wiring your
speakers.
• Don't connect different speakers from the same
terminal in this way.
82
En
This receiver has more than enough power for any home
use, but it’s possible to add additional amplifiers to every
channel of your system using the pre-outs. If you use
additional amps for the front channels take out the Ushaped connectors (see item 8 in Rear panel on page 14).
Make the connections shown below to add amplifiers to
power your speakers.
Other connections
10
Multi-room setup
Note
• Before making or changing the connections, switch
off the power and disconnect the power cord from the
AC outlet.
ANALOG
INPUT
L
R
DIGITAL
S400
USB AUDIO
IN
PHONO
OUT 2
OUT 1
ANALOG
R AUDIO L
INPUT
6
AUDIO
CD
IN
(DVR/
VCR1)
(SAT)
IN
ANALOG
R
R
L
OUT
(CD)
2 IN
(TV/
DVD)
INPUT
Powered subwoofer
SUB W.
IN
PLAY
PRE OUT
1
OUT
2
SURROUND
R
R
1 IN
(DVD/
LD)
FRONT
(DVD/
LD)
SURROUND
R
R
L
INPUT
SURROUND
BACK
IN
PLAY
SUB W.
L
L
R
(Single)
CENTER
L
SURROUND
BACK
L
R
MULTI CH INPUT
L (Single)
Making multi-room connections
ANALOG
REC
TAPE2
MONITOR
2RF
IN
ASSIGNABLE
L
CENTER
REC
CD-R/
TAPE1
/MD
(Single)
3 IN
L
POWER
AMP
IN
FRONT
(CD-R/
TAPE1/
MD)
IN
4
Center channel
amplifier (mono)
IN
R
IN
5
Front channel
amplifier
(AUDIO)
When used together with an optional IR receiver, this
receiver can power two independent systems in separate
rooms. Different sources can be playing in both rooms at
the same time or, depending on your needs, the same
source can also be used. The main and sub rooms have
independent power (the main room power can be off
while the sub room is on) and the sub room can be
controlled by this unit's remote control. You may need to
specify your volume setting and IR receiver type in MultiRoom Setting on page 95.
Surround
channel
amplifier
ANALOG
INPUT
L
R
Surround back
channel amplifier
• You can use the additional amplifier on the surround
back channel pre-outs for a single speaker as well. In
this case plug the amplifier into the left (L (Single))
terminal only.
Connecting an external stereo pre-amplifier
It’s possible to use a separate stereo pre-amp with this
receiver if necessary. You might want to do this if you
need to connect more sources than this receiver can
accommodate, or if you prefer to use a specific pre-amp
for sound quality reasons. You can connect sources to
either this receiver or to the external pre-amp (giving you
a greater number of input possibilities).
It is possible to make these connections if you have a
separate amplifier, speakers, TV and an IR receiver (such
as the Pioneer MR-100) for your sub room.
1 Connect the IR receiver sensor to the green
MULTI-ROOM & SOURCE REMOTE IN jack on the rear
of this receiver.
2 Connect a separate amplifier and TV monitor to
the MULTI-ROOM & SOURCE OUT jacks on the rear of
this receiver.
You should have a pair of speakers attached to the sub
room amplifier as shown in the illustration below.
CONTROL
Sub room
Note that with sources connected this receiver, any
signal sent to the two front channels will be sent to the
pre-amplifier before being heard through the front
speakers in your system.
2 Use a stereo RCA audio cable to connect the
FRONT PRE OUT jacks of this receiver to a stereo
input on the pre-amp.
For example, connect to the CD or tape inputs on the rear
of the pre-amp. You’ll have to select that source if you
want to hear the stereo signal from this receiver.
3 Use a stereo RCA audio cable to connect the
stereo pre-out jacks of the pre-amp to the POWER
AMP IN jack of this receiver.
This will allow you to hear the stereo source from the
external pre-amp through this receiver. For stereo
sources connected directly to the external pre-amp, this
receiver acts as a standard power amplifier. For digital
sources connected to this receiver, the receiver acts as a
digital decoder/digital-to-analog converter and as a
power amplifier.
MONITOR
OUT 2
DVD/
LD
IN
IN
TV/
DVD
IN
IN
REMOTE IN
MULTI ROOM &
SOURCE
COMPONENT VIDEO
(DVD/
LD)
IN
1 Y
A
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
MULTIROOM &
SOURCE
IN
PHONO
OUT 2
R
AUDIO
L
IN
AUDIO
CD
OUT 1
6
IN
5
IN
(CD-R/
TAPE1/
MD)
(DVR/
VCR1)
IN
4
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
L
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
MONITOR
OUT 2
AC OUTLET
FRONT
AC 120 V 60Hz
COMPONENT VIDEO
DVD/
LD
IN
IN
TV/
DVD
IN
IN
SAT
IN
IN
OUT
DVR/
VCR1
IN
OUT
OUT
OUT
(DVD/
LD)
IN
1 Y
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
SWITCHED 100W (0.8A) MAX
R
CENTER
PB
AC IN
PR
PR
CENTER
OUT
REC
CD-R/
TAPE1/
MD
IN
SUB W.
PRE OUT
1
PLAY
3 IN
POWER
AMP
IN
Y
MONITO
OUT
PB
PB
Main room
ASSIGNABLE
1 Remove the U-shaped connectors that connect
the FRONT PRE OUT jacks to the POWER AMP IN
jacks.
MONITOR
OUT 1
IN
MULTIROOM &
SOURCE
(Single)
OUT
REC
TAPE 2
MONITOR
IN
L
R
SUB W
R
SELECTABLE (SURROUND BACK & B )
R
B
PR
L
L (Single)
OUT
R
L
AUDIO
RS-232C
VIDEO
L
R
1
IN
IN
R
(Single)
SURROUND
BACK
VCR3
SURROUND
BACK
L
SURROUND
PB
ASSIGNABLE
IN
CENTER
L
MULTI CH INPUT
L
Y
PR
VCR2
(Single)
OUT
R
IN
3
Y
PB
SURROUND
L
SURROUND
IN
2
IN
2
R
R
IN
PLAY
FRONT
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
SPEAKERS
IR receiver
(MR-100, etc.)
Note
• It is not possible to hear the digital output of a
component in the sub room. However, you can
connect the analog outputs of your digital
component into the receiver’s (analog) input
terminals to hear the component in the sub room.
• You can't use sound controls (such as the tone
controls or Midnight listening) or any surround
modes in the sub room. You can, however, use the
features available with your sub room amplifier.
83
En
10
Other connections
• When selected in the main room, i.LINK sources
can’t be heard in the sub room unless they can
output both i.LINK and analog signals at the same
time. Also, the sound from an i.LINK source selected
in the sub room switches off if the same source is
selected as an i.LINK source in the main room.
Tip
• Press MR&S ON/OFF to use the buttons on the Sub
Room Control screen in the sub room.
RECEIVER
Using the sub room controls
You can use the remote to adjust the sub room volume
and select sources from either the main room or the sub
room. You can also do this using the front panel controls.
DVD
/LD
DVR
/VCR1
TV
SAT
CD
CD-R
/TAPE1
TUNER
Important
4/4
- Sub Room Control MR&S
– VOLUME +
ON/OFF
INPUT
• The receiver must be switched on (or in standby) in
the main room to control the sub room.
Using the remote control in the main room
Using the remote control in the sub room
1 Point the remote control at the IR receiver and
press RECEIVER.
This switches on the multi-room feature (MULTI
ROOM&SOURCE).
2 Use the Home menu screen buttons to control
the sub room.
The INPUT buttons work for the sub room the same way
they would for the main room (see Home menu screens
on page 33 for more detail), and the hard-key volume
controls adjust the volume in the sub room.
1 From the receiver menu screens on the remote
control, select the Sub Room Control screen.
If you’re unsure how to do this, see Receiver menu
screens on page 34.
RECEIVER
DVD
/LD
DVR
/VCR1
TUNER
1/3
HOME
RECEIVER
2
3
RECEIVER
1
SAT
CD
CD-R
/TAPE1
INPUT
RECEIVER
INPUT 2
DVD
/ LD
TV
/ DVD
SAT
VCR2
VCR3
DVR
/ VCR1
CD
TUNER
VIDEO
MULTI CH
INPUT
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
TV
CONT
MULTI
OPERATION
SETUP
TV
2/3
HOME
RECEIVER
INPUT 1
4/4
- Sub Room Control MR&S
– VOLUME +
ON/OFF
SETUP
3
CD-R
/ TAPE1
SYSTEM
OFF
2 Press MR&S ON/OFF to switch on the multi-room
feature.
You can also press the MULTI ROOM & SOURCE ON/
OFF button on the front panel.
The MULTI ROOM indicator lights on the front panel to
indicate the multi-room feature has been switched on.
3 Use the Sub Room Control screen buttons the
same way you control this receiver from the main
Home menu.
The source input buttons work the same way as the
controls listed in Home menu screens on page 33, and
the on-screen volume control adjusts the sub room.
84
En
Other connections
10
Using the i.LINK interface
Using the front panel multi-room controls
ACOUSTIC
CAL.
SB CH
MODE
TUNER
MIDNIGHT
TONE
OPTION
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
DIGITAL NR
CLASS
STATION
MULTI ROOM & SOURCE
CONTROL
ON/OFF
VIDEO INPUT
PHONES
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
1 Press the MULTI ROOM & SOURCE ON/OFF
button on the front panel.
The MULTI ROOM indicator lights on the front panel to
indicate the multi-room control has been switched on.
2 Press CONTROL.
Make sure that any operations for the sub room are done
while MULTI ROOM shows in the display. If MULTI
ROOM is not showing, the front panel controls affect the
main room only.
3 Use the INPUT SELECTOR dial to select the source.
Select between DVD/LD, TV/DVD, SAT, DVR/VCR 1, CD,
CD-R/TAPE 1 or TUNER (in that order).
If you select TUNER, you can use the front panel TUNER
controls to select a preset station (see Listening to
memorized station presets on page 56 if you’re unsure
how to do this).
4 Use the MASTER VOLUME dial to adjust the
volume.
This is only possible if you selected the VARIABLE
volume control in Multi-Room Setting on page 95.
5 When you’re finished, press CONTROL again to
return to the main room controls.
You can also press the MULTI ROOM & SOURCE ON/
OFF button on the front panel to switch off all output to
the sub room.
Note
• Multi-room can’t be used when you’re setting up the
system (from the on-screen System Setup menu).
If you have a component with an i.LINK connector, you
can connect it to this receiver using an i.LINK cable.
Since the i.LINK interface does not transmit video
signals, the video signal of i.LINK-connected components must be connected with other cables (see
Connecting your equipment on page 14 for more on
making video connections). If you’ve already hooked up
the video signal from the component, assign the i.LINK
input to the input function to which you’ve connected the
video signals (see Assigning the i.LINK inputs on
page 91).
The two i.LINK connectors on the rear of your receiver are
4-pin connectors. Use a 4-pin, S400 i.LINK cable to
connect i.LINK-equipped components.
Important
• Please use 4-pin, S400 cables less than 3.5 meters
long. Although longer ones are available, they may
not work reliably.
• If your i.LINK connector comes into contact with
metallic parts of the receiver other than the i.LINK
terminal, an electrical short may occur. Some cables
have metal parts that may touch the unit when
connected. Please take care to use a suitable i.LINK
cable only.
• There may be cases where the PQLS/rate control
function and/or the i.LINK audio does not work properly even when connected to i.LINK Audio-compatible equipment.
• During playback through an i.LINK connection, do
not disconnect i.LINK cables or switch off any
components connected using i.LINK.
• Copy-protected 96kHz DVD-Video discs can be heard
through the i.LINK connection, but they will be downsampled to 48kHz.
• If you’re using a Pioneer amplifier in the sub room,
you may want to cover the remote sensor so that this
remote control doesn’t accidently control the sub
room amplifier.
• You won’t be able to switch the main room off
completely unless you’ve switched off the multi-room
control first.
• When someone is controlling the system from the
main room, you won’t be able to operate the sub
room controls.
85
En
10
Other connections
• Use an i.LINK cable to connect one of the i.LINK
connectors on this receiver to an i.LINK connector on
your i.LINK component.
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
IN
PHONO
OUT 2
R
AUDIO
L
AUDIO
CD
6
R
(SAT)
R
L
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
L
Y
MONITOR
OUT
PB
PB
SAT
IN
IN
OUT
DVR/
VCR1
IN
OUT
OUT
OUT
PR
PR
SUB W.
PRE OUT
1
PLAY
(TV/
DVD)
IN
REC
CD-R/
TAPE1/
MD
IN
(Single)
OUT
(CD)
2 IN
TV/
DVD
IN
REMOTE IN
MULTI ROOM &
SOURCE
COMPONENT VIDEO
(DVD/
LD)
IN
1 Y
CENTER
OUT
(DVR/
VCR1)
IN
3 IN
IN
POWER
AMP
IN
IN
(CD-R/
TAPE1/
MD)
IN
4
MONITOR
OUT 2
DVD/
LD
IN
IN
OUT 1
IN
5
MULTIROOM &
SOURCE
REC
R
TAPE 2
MONITOR
IN
R
PLAY
FRONT
SUB W
L
L
R
MULTI CH INPUT
IN
PB
PR
VCR2
IN
IN
OUT
OUT
PR
ASSIGNABLE
Pioneer's PQLS (Precision Quartz Lock System)
technology provides high-precision digital audio from
DVD-A, SACD and audio CD sources when you use the
i.LINK interface. A precision quartz controller in this
receiver eliminates distortion caused by timing errors
(jitter), giving you the best possible digital-to-analog
conversion from the digital source.
To take advantage of PQLS, you must have a player
compatible with rate-control, and it must be switched on
and connected to this receiver through the i.LINK
network.
(Single)
CENTER
VCR3
SURROUND
BACK
R
Y
PB
SURROUND
L
IN
3
Y
2
L
R
SURROUND
ASSIGNABLE
IN
2
About PQLS rate control
L (Single)
IN
IN
R
L
AUDIO
RS-232C
VIDEO
12V TRIGGER
Creating an i.LINK network
S2 VIDEO
S400
(AUDIO)
i.LINK-equipped component
• The arrow on the cable connector body should be
face down for correct alignment with the connector
on the player. When properly connected, the i.LINK
plug will snap into the connector. If not connected
properly the receiver will not be able to recognize any
connected components.
Using i.LINK it is possible to chain up to 17 components
together so that the digital audio and control signals
from each component is available to other components
in the network. With the addition of an i.LINK repeater,
it’s possible to connect up to 63 components.
i.LINK connectors come in 4-pin and 6-pin configurations. This player uses the 4-pin connection, but the two
types can be mixed on a network.
This receiver is compatible with i.LINK Audio (A&M
protocol) components, such as DVD players. Note that
when connected to i.LINK MPEG-II TS equipment (such
as a digital satellite tuner), i.LINK DV equipment (such as
a DVD recorder or DV camcorder), or an i.LINK-equipped
personal computer, audio and video signals are not
transmitted, and connecting to these devices sometimes
causes network interruptions. Check the operating
instructions supplied with your other i.LINK components
for compatibility information.
This receiver is DTCP (Digital Transmission Content
Protection) compliant, so you can play DVD-A, DVDVideo, and SACD i.LINK audio.
When setting up an i.LINK network, it’s important that
the components form an open ended chain (fig. 1), or a
tree (fig. 2).
Note
fig. 1
i.LINK cable
• You can connect several components together using
i.LINK. See Creating an i.LINK network below.
About i.LINK
i.LINK is a trademark name for IEEE1394, a high-speed
interface for digital audio, video and other data found on
personal computers, digital camcorders, and other kinds
of audio and audio/visual equipment. A single i.LINK
connector can both send and receive data at the same
time, so only one cable is required to connect components for two-way communication.
“i.LINK” and the “i.LINK” logo are trademarks of Sony
Corporation.
86
En
fig. 2
i.LINK cable
Other connections
10
The system will not work if the connected components
form a loop. If a loop is detected, the message LOOP
CONNECT shows in the display. Figs. 3 and 4 show
connections that form a loop.
fig. 3
fig. 4
i.LINK cable
i.LINK cable
Using the USB interface
It is possible to listen to multichannel audio sources from
your computer by connecting to the USB interface on the
rear of this receiver. Depending on your model of
computer and the software installed, you can listen to
any source compatible with your operating system
through the speaker setup you’ve connected to this
receiver.
1 Connect your computer’s USB terminal to the
USB terminal on the rear panel of this receiver.
CONTROL
MONITOR
OUT 1
DIGITAL
OUT
USB AUDIO
S400
IN
(AUDIO)
IN
PHONO
OUT 2
R
AUDIO
L
Another consideration when connecting i.LINK devices
is the speed of the interface. At present there are three
speeds; S100 (slowest), S200 and S400 (fastest). This
receiver uses the S400 type. Although you can use
components with different speeds together, we
recommend connecting slower-speed components at
the edge of the network if possible (shown by the shaded
boxes in figs. 1 and 2). This will keep the network free of
bottlenecks.
When used within an i.LINK network, this receiver must
be on for the i.LINK connection to be maintained. Other
components in the network may or may not maintain the
connection in standby (none will when the power is
completely off)—check the operating instructions
supplied with individual components. Note that the audio
may be momentarily interrupted if a component in the
i.LINK network is switched on/off, or its i.LINK
connection is switched on/off.
This product complies with the following i.LINK interface
specifications:
1) IEEE Std. 1394a-2000, Standard for a High Performance
Serial Bus
2) Audio and Music Data Transmission Protocol 2.0
Following the standard for AM824 sequence adaptation
layers, the product is compatible with IEC60958 bitstream,
DVD-A and SACD.
IN
5
AUDIO
(DVR/
VCR1)
(SAT)
IN
R
R
L
(CD)
2 IN
(TV/
DVD)
1 IN
(DVD/
LD)
2RF
IN
(DVD/
LD)
TV/
DVD
IN
IN
SAT
IN
IN
L
Y
AM LOOP
ANTENNA
MONITOR
OUT
PB
FM
75Ω UNBAL
PB
PR
PR
REC
SUB W.
PRE OUT
1
(Single)
OUT
REC
R
TAPE 2
MONITOR
IN
R
PLAY
FRONT
R
SUB W
R
R
OUT
OUT
OUT
IN
2
L
L
IN
3
Y
Y
IN
PB
SURROUND
PB
PR
VCR2
IN
IN
OUT
OUT
PR
ASSIGNABLE
(Single)
CENTER
VCR3
SURROUND
BACK
L
MULTI CH INPUT
OUT
DVR/
VCR1
IN
2
L
SURROUND
ASSIGNABLE
ANTENNA
REMOTE IN
MULTI ROOM &
SOURCE
COMPONENT VIDEO
(DVD/
LD)
IN
1 Y
CENTER
OUT
CD-R/
TAPE1/
MD
IN
PLAY
3 IN
IN
POWER
AMP
IN
IN
(CD-R/
TAPE1/
MD)
IN
4
MONITOR
OUT 2
DVD/
LD
IN
IN
CD
OUT 1
6
MULTIROOM &
SOURCE
L (Single)
1
IN
IN
R
L
AUDIO
RS-232C
VIDEO
S2 VIDEO
12V TRIGGER
DC OUT 12V
TOTAL 100mA MAX
2
VSX-59TXi
Personal computer
2
Switch on your computer and this receiver.
3 If you’re connecting for the first time, wait for
the USB driver installation to finish.
The installation may take a minute or two to complete.
Make sure you leave the USB cable connected until the
dialog box indicates that the USB setup is finished. Note
that some older operating systems may require a disc for
installation.
4 Press ‘USB’ on the remote control Home menu
( ) screen.
You can also use the INPUT SELECTOR dial on the front
panel to select USB.
5 Make any necessary settings required to select
the USB interface as your computer audio output.
You will need to access your speaker settings from the
Control Panel of your operating system:
• Windows® XP – Select Sound, Speech, and Audio
Devices, and then select Change the speaker
settings. Select Audio, then PIONEER AV Receiver/
Amplifier from the drop down menu.
87
En
Other connections
10
• Windows® 98SE – Select Multimedia, and then
select Audio. Choose PIONEER AV Receiver/
Amplifier from the drop down menu.
•
Windows®
Me/Windows®
2000 – Select Sound
and Multimedia and then select Audio. Choose
PIONEER AV Receiver/Amplifier from the drop
down menu.
You will also need to make sure the correct speaker
setting is selected with the audio software you’re using.
Please refer to the manual that came with the software to
make these settings.
6 Turn up the volume control on your computer
and this receiver.
You may want to start with a fairly low volume on this
receiver and turn it up as necessary after you’ve checked
your levels.
7
Start playback of a source on your computer.
8 If necessary, press SIGNAL SELECT to choose the
number of channels you’ll hear.
See Selecting USB and multichannel analog input
channels on page 49 for more on this.
Note
• Windows® XP, Windows® 2000, Windows®
Millennium Edition and Windows® 98 Second
Edition operating systems have been tested for
compatibility with this interface, but depending on
your computer setup, you may find that your system
is not compatible.
• This USB interface supports up to 8 channels of
audio.
• Make sure you use a USB cable that connects from
an A-type connector (from your PC) to a 4-pin B-type
connector (to the receiver).
• The USB specification is version 1.1 compatible, and
the USB Audio Class specification is 1.0 compatible.
• You won’t be able to control this receiver using your
computer (and vice-versa).
• Sampling formats up to 48kHz can be heard using
the USB connection (formats above 48kHz sampling
must be downsampled).
• Any computer alert sounds will also be heard
through the speakers unless you switch them off
from the computer’s control panel.
• You won’t be able to hear the audio from the USB
connection through the digital outputs of this
receiver.
• Even when the receiver is switched off, it will remain
selected in your speaker settings.
• Note that using hubs or extensions may cause
connection problems.
88
En
Caution
• Make sure you don’t switch off the computer or
unplug the USB cable during playback.
• To prevent noise being output, don’t use other
software on your computer during playback.
• Pioneer is not responsible for computer system
damage, software crashes or failures, or any other
possible computer problems due to this
configuration.
Microsoft Windows® XP, Windows® 2000, Windows®
Millennium Edition and Windows® 98 Second Edition are
registered trademarks of Microsoft Corporation, Inc.
Connecting a PC for Advanced
MCACC output
If you used the Professional Acoustic Calibration EQ on
page 63 to measure the reverb characteristics of your
listening room, you’ll be able to connect a computer
using the RS-232C jack on the back panel to check the
results graphically. Use a commercially-available RS232C cable to connect the RS-232C jack on your
computer to the 9-pin RS-232C jack on this receiver (the
cable must be cross type, female–female).
To obtain the software to output the results, please
register this unit online as instructed on the front cover
of the manual. After registering, you will be able to
access the download area from the Pioneer website,
where both the software and instruction manual will be
available. If you have any questions regarding, please
contact the Customer Support Division of Pioneer.
Please make sure your system meets the following
requirements:
• Operating system must be Windows® XP, Windows®
2000, Windows® Millennium Edition, Windows® 98
Second Edition, or Windows® NT 4.0 (Service pack 6).
• CPU must be at least Pentium 3 / 300MHz or AMD K6
/ 300MHz (or equivalent) with at least 128MB of
memory, and your monitor must be able to display a
minimum resolution of 800x600.
• An RS-232C port connector is necessary for
graphical output. Refer to the operating instructions
and/or the PC manufacturer for more information on
making the proper port settings.
• System must have internet access.
Before doing these steps, make sure you complete steps
1–6 in Using Professional Acoustic Calibration EQ on
page 64.
Other connections
10
1 Select ‘PC Output’ and press ENTER.
When the receiver is ready for transmission, Operate a
PC shows on the OSD.
2.4. Acoustic Cal EQ Pro.
Manual Pro.
2.4. Acoustic Cal EQ Pro.
[ Reverb Measurement ]
_
Operate a PC
[ Reverb View ]
[ PC Output ]
[ Advanced EQ Setup ]
[Return]
[Return]
• If PC Output isn’t displayed, the receiver probably
doesn’t have any transmission data. Make sure you
have completed steps 1–6 in Using Professional
Acoustic Calibration EQ on page 64.
2 Connect your computer to the RS-232C jack on
the rear panel of the receiver.
Use a commercially-available cable to connect the RS232C jack on your computer to the 9-pin RS-232C jack on
this receiver. See the documentation provided with the
Advanced MCACC application for more information.
RS-232C
PC
3 Start the MCACC application on your computer.
Follow the instructions provided with the application. It
will take about ten seconds for the transmission to
complete, then you will be able to analyze the output on
your computer. Since the data will be cleared from the
receiver when you restart reverb measurement or turn off
the receiver, you might want to save the information on
your PC after measurement.
4 When you’re finished, select ‘Return’ on the onscreen display.
You’ll be taken to the Advanced EQ Setup. Depending on
the results, you may want to continue with the Advanced
EQ setup (see Setting Professional Acoustic Calibration
EQ according to your room characteristics on page 63 for
more on this). You can also simply press Return again to
exit the Professional Acoustic Calibration EQ setup.
89
En
11
Advanced setup
Chapter 11
Advanced setup
The Input Assign menu
Assigning the digital inputs
You only need to make settings in the Input Assign menu
if you didn’t hook up your digital equipment according to
the default settings for the digital inputs, or if you have
connected equipment using component video or i.LINK
cables.
• Default settings:
Digital-1 (coaxial) – DVD/LD
Digital-2 (coaxial) – TV/DVD
Digital-3 (coaxial) – CD
To access the Input Assign menu, follow the steps below.
Digital-4 (optical) – SAT
1 Make sure your receiver and TV are both
switched on.
Digital-6 (optical) – CD-R (/TAPE1/MD)
2 Using the remote control, press RECEIVER on the
touch screen, then press the SYSTEM SETUP button.
1/3
HOME
RECEIVER
Digital-5 (optical) – DVR (/VCR1)
2 RF (coaxial) – DVD/LD
You only need to do this if you didn’t hook up your digital
equipment according to the default settings for the
digital inputs (see above). This setting tells the receiver
what digital equipment is hooked up to which terminal so
the buttons on the remote correspond to what you have
hooked up.
RECEIVER
INPUT 1
2
1 Select ‘Digital In’ from the Input Assign menu
and press ENTER.
3
DVD
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
1.Input Assign
[
[
[
[
SETUP
1.Digital In ]
2.Component Video In ]
3.i.LINK In ]
4.Video Assign ]
[Return]
ENTER
CHANNEL
VOLUME
MENU
MUTE
SYSTEM
SETUP
AV AMPLIFIER
An on-screen display (OSD) appears on your TV. Use the
/// hard keys and ENTER on the remote control
to navigate through the screens and select menu items.
• The / (cursor up/down) hard keys select menu
items and the / (cursor left/right) hard keys
change the setting of the item selected.
3 Select ‘Input Assign’ then press ENTER.
The Input Assign menu appears on screen:
System Setup
1.Input Assign
[Auto Surround Setup]
[1.
[2.
[3.
[4.
Input Assign ]
Surround Setup ]
Expert Setup ]
THX Audio Setup ]
[
[
[
[
1.Digital In ]
2.Component Video In ]
3.i.LINK In ]
4.Video Assign ]
[Return]
[Exit]
90
En
2 Select the number of the digital input to which
you’ve connected your digital component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
1.1. Digital-In
Digital-1
Digital-2
Digital-3
Digital-4
Digital-5
Digital-6
RF IN
[ DVD/LD ]
[ TV/DVD ]
[ CD ]
[ SAT ]
[ DVR ]
[ CD-R ]
[ DVD/LD ]
[Return]
3 Use the / (cursor left/right) hard keys to
select the component that corresponds with the one
you connected to that input.
Select between DVD/LD, TV/DVD, SAT, DVR/VCR 1,
VCR 2, VCR 3 or CD-R (however, the RF IN setting doesn't
include CD-R).
• If you assign a digital input to a certain function (for
example, DVD/LD) then any digital inputs previously
assigned to that function will automatically be
switched off.
Advanced setup
4 When you're finished, select RETURN and press
ENTER.
You will return to the Input Assign menu.
Assigning the component video inputs
• Default settings:
Component 1 – DVD/LD
Component 2 – OFF
Component 3 – OFF
If you used component video cords to connect your video
equipment you must tell the receiver which device it is, or
else you may see the S-video or composite video input
instead of the component video signal.
1 Select ‘Component Video In’ from the Input
Assign menu and press ENTER.
1.Input Assign
[
[
[
[
1.Digital In ]
2.Component Video In ]
3.i.LINK In ]
4.Video Assign ]
[Return]
2 Select the number of the component video input
to which you’ve connected your video player.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
1.2. Component Video In
Component 1 [DVD/LD ]
Component 2 [ OFF ]
Component 3 [ OFF ]
[Return]
3 Use the / (cursor left/right) hard keys to
select the component that corresponds with the one
you connected to that input.
• If you connect the TV monitor with component video
cord, and the DVD player with composite or S video
cord then you should set that terminal to OFF.
4 When you're finished, select RETURN and press
ENTER.
You will return to the Input Assign menu.
11
Assigning the i.LINK inputs
If you assign i.LINK-equipped components to an input
(for example DVD/LD), you will be able to select both
audio and video signals from i.LINK-equipped
components using the INPUT button (or INPUT
SELECTOR dial on the front panel). Assigning i.LINK
sources also allows you to keeps the sound settings
you’ve made for other input functions.
1 Select ‘i.LINK Input’ from the Input Assign menu
and press ENTER.
If no i.LINK-equipped components are connected i.LINK
Input cannot be selected.
1.Input Assign
[
[
[
[
1.Digital In ]
2.Component Video In ]
3.i.LINK In ]
4.Video Assign ]
[Return]
2 Select an i.LINK-equipped component.
When a number of i.LINK-equipped components are
connected to your receiver, the i.LINK-equipped
component you are looking for might be listed on
additional display screens.
• i.LINK is displayed after unassigned device names
(e.g. DV-59AVi [i.LINK]).
• If a connected devices cannot output (playback) a
source using the i.LINK connection, [- - - -] is
displayed after the input device name (e.g. DV-59AVi
[- - - -]). Non-compatible devices cannot be assigned
to inputs.
• When the cables for an assigned input device
become loose or the power is cut to the device, an
asterisk (*) appears before the device name (e.g.
*DV-59AVi [CD]).
3 Use the / (cursor left/right) hard keys to
select the component that you want to assign.
When you assign an i.LINK-equipped video component,
select the input source to which you have connected the
video signal from the component.
• If you assign an i.LINK input to a certain function (for
example DVD/LD) then any digital inputs previously
assigned to that function will automatically be set to
i.LINK (not assigned).
• TUNER and PHONO inputs cannot be assigned.
4 When you're finished, select RETURN and press
ENTER.
You will return to the Input Assign menu.
91
En
11
Advanced setup
Assigning the video inputs
• Default settings:
MULTI IN – OFF
USB – OFF
You can choose to watch a video source at the same time
as you listen to the audio source from the multichannel
analog inputs or USB connector. To do this, you must let
the receiver know which video component you want to
watch. After making the settings below, the
corresponding video input is selected at the same time
that you choose either MULTI IN or USB as the input
source.
1 Select ‘Video Assign’ from the Input Assign menu
and press ENTER.
The Expert Setup menu
The settings in the Expert Setup menu are more
advanced features of this receiver that you can use to
make detailed adjustments when you’re more familiar
with the system.
You only need to make these settings once (unless you
change the placement of your current speaker system or
add new speakers.).
1 Make sure your receiver and TV are both
switched on.
2 Using the remote control, press RECEIVER on the
touch screen, then press the SYSTEM SETUP button.
1.Input Assign
[
[
[
[
1/3
HOME
RECEIVER
1.Digital In ]
2.Component Video In ]
3.i.LINK Input ]
4.Video Assign ]
RECEIVER
INPUT 1
2
3
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
DVD
/ LD
[Return]
2 Select which input to which you want to assign a
video source.
Choose either MULTI IN or USB.
SETUP
3 Use the / (cursor left/right) hard keys to
select the video source you want to assign.
Any video source available on the receiver can be
assigned, and you can also assign the same video source
to both inputs.
4 When you're finished, select RETURN and press
ENTER.
You will return to the Input Assign menu.
ENTER
CHANNEL
MENU
VOLUME
MUTE
SYSTEM
SETUP
AV AMPLIFIER
An on-screen display (OSD) appears on your TV. Use the
/// hard keys and ENTER on the remote control
to navigate through the screens and select menu items.
• The / (cursor up/down) hard keys select menu
items and the / (cursor left/right) hard keys
change the setting of the item selected.
3
Select ‘Expert Setup’ then press ENTER.
System Setup
[Auto Surround Setup]
[1.
[2.
[3.
[4.
Input Assign ]
Surround Setup ]
Expert Setup ]
THX Audio Setup ]
[Exit]
92
En
Advanced setup
4
Select the setting you want to adjust.
3.Expert Setup
[1. OSD Adjustment ]
[2. Bass Peak Level ]
[3. D-Range Control ]
[4. Function Rename ]
[5. OSD Overlay ]
[6. 12V Trigger ]
[7. Multi-Room Setting ]
[Return]
11
Bass Peak Level
Some audio sources (for example, Dolby Digital and DTS)
include ultra-low bass tones. Set the bass attenuator as
needed to prevent the ultra-low bass from distorting the
sound.
1 Select ‘Bass Peak Level’ from the Expert Setup
menu.
The current setting is displayed.
• When [- - -] is displayed, no bass is output.
• OSD Adjustment – Adjust the position of the onscreen display on your TV.
• Bass Peak Level – Prevent bass tones from distorting
the sound from your speakers.
• D-Range Control – Specify the amount of dynamic
range adjustment to Dolby Digital soundtracks.
• Function Rename – Change the names that appear
on the receiver display and on-screen display.
• OSD Overlay – Switch the on-screen display (for
basic functions) on or off.
• 12V Trigger – Specify which components are
switched on or off using the 12 volt trigger.
• Multi-Room Setting – Specify your volume setting
and IR receiver type for a multi-room setup.
5 Make the adjustments necessary for each
setting, pressing ENTER to confirm after each screen.
When you’re finished, you can select Return, then press
ENTER to go back to the System Setup menu.
• When [OFF] is displayed the attenuator is off (bass
output is not affected).
2
Select a setup option.
3.2. Bass Peak Level
Manager
[Setting Start]
[Setting Cancel]
[Return]
Present Level [OFF]
• Setting Start – The volume is set to MIN (----dB), a
test tone plays back and you make the setting.
• Setting Cancel – Switches the attenuator off.
3 If you selected ‘Setting Start’, use the /
(cursor left/right) hard keys to adjust the test tones
and specify the bass peak level then press ENTER.
3.2. Bass Peak Level
Manager
OSD Adjustment
Use this feature to adjust your TV display if it seems
difficult to see all the instructions on the screen.
[Setting OK]
Bass Peak Level
[–10]
[Setting Cancel]
1 Select ‘OSD Adjustment’ from the Expert Setup
menu.
2 Use the /// hard keys to move the
display field around until you get one that you feel
best suits your TV.
You can move the screen displays up or down and left or
right to get the best match for your TV.
Set the bass peak level gradually, then press ENTER at
the point just before the tone starts to distort. When
you’re finished, the display on the receiver will show
RESUME and the volume will return to its original
position.
• The test tones are output at loud volumes.
3.1. OSD Adjustment
[Return]
3 Press ENTER.
You will return to the Expert Setup menu.
• If the YES or PLUS setting on the subwoofer is
selected (in Speaker Systems on page 58), the test
tone will only play back from the subwoofer. If not, the
test tone will play back from all speakers set to
LARGE (except for the subwoofer).
4 When you're finished, select RETURN and press
ENTER.
You will return to the Expert Setup menu.
93
En
Advanced setup
11
3
Note
Edit the name as necessary and press ENTER.
• Since the THX Ultra2 feature has a bass limiter to
control bass peaks, the bass attenuator is
automatically switched off if you set up your system
using the THX Ultra2 Subwoofer Setup on page 96.
3.4. Function Rename
DVR
[
DVR
]
VIDEO
DVR
VCR2
VCR3
[
[
[
[
VIDEO
DVR
VCR2
VCR3
]
]
]
]
Dynamic Range Control
• Default setting: OFF
This setting specifies the amount of dynamic range
adjustment to movie soundtracks. You may want to use
this when listening to surround sound at low volumes.
Use the / (cursor up/down) hard keys to change the
character and the / (cursor left/right) hard keys to
move forward/back a position. The name can be up to ten
characters (the possible characters are listed below).
1 Select ‘D-Range Control’ from the Expert Setup
menu.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
2
0123456789
abcdefghijklmnopqrstuvwxyz
Choose the setting that you want.
!”#$%&’()*+,–./:;<=>[email protected][ \ ]
3.3. Dynamic Range
Control
Compression Level
[MID]
[OFF]
3.4. Function Rename
dts
[Return]
• OFF – No dynamic range adjustment (use when
listening at higher volume).
• MID – Mid setting.
• MAX – Dynamic range is reduced (loud sounds are
reduced in volume while quieter sounds are
increased)
3 When you're finished, select RETURN and press
ENTER.
You will return to the Expert Setup menu.
Function Rename
You can customize the names that appears on the
display when you select an input source (for example,
you could change the name of VCR1/DVR to DVR-310).
1 Select ‘Function Rename’ from the Expert Setup
menu.
2 Select the name of the input you want to rename
and press ENTER.
The functions are divided into three different on-screen
displays so you may have to move through them to find
the function you want to rename.
DVR
[
DVR-310
]
VIDEO
DVR
VCR2
VCR3
[
[
[
[
VIDEO
DVR
VCR2
VCR3
]
]
]
]
4 Select another name to edit, or select ‘Return’
from the bottom of the list if you’re done. Press
ENTER.
If you’ve selected another name, repeat step 3, otherwise
you’ll return to the Expert Setup menu.
OSD Overlay
• Default setting: ON
You can choose whether or not you want to see basic
functions (such as selecting input sources) using the onscreen display. Only the System Setup menu and Status
screen (Checking your system settings on page 78)
appear on the OSD.
1 Select ‘OSD Overlay’ from the Expert Setup
menu.
2
Choose the setting that you want.
3. 5. OSD Overlay
Overlay
[ON ]
3.4. Function Rename
DVD/LD
[
DVD/LD
]
DVD/LD
TV
SAT
[
[
[
DVD/LD
TV/DVD
SAT
]
]
]
[Return]
• OFF – The on-screen display is switched off except for
the System Step menu and Status screens.
• ON – The on-screen display is switched on for basic
functions.
94
En
Advanced setup
11
3 When you're finished, select RETURN and press
ENTER.
You will return to the Expert Setup menu.
2
12 Volt Trigger
Select the volume level setting.
• VARIABLE – Use this setting if you’ve connected a
power amplifier in the sub room (this receiver is
simply being used as a pre-amp) and you will be
using this receiver’s controls to adjust the volume.
• FIXED – Use this setting if you’ve connected a fully
integrated amplifier (such as another Pioneer VSX
receiver) in the sub room and want to use that
receiver’s volume controls.
• Default setting: OFF · OFF (all components)
After connecting a component to one of the 12 volt
triggers (see Switching components on and off using the
12 volt trigger on page 74), it switches on automatically
when you select an input function set to switch the
trigger on. Specify which input functions switch on
which trigger(s) below.
3.7. Multi-Room Setting
Volume Level
[VARIABLE]
IR Receiver
[PIONEER ]
[Return]
1 Select ‘12 Volt Trigger’ from the Expert Setup
menu.
2 Select an input function and choose the setting
that you want.
This should be the input function, that when selected,
switches on one (or both) of the 12 volt triggers.
3.6. 12V Trigger
DVD/LD
TV/DVD
SAT
VIDEO
DVR/VCR1
VCR2
VCR3
( Next)
3.6. 12V Trigger
1
2
[OFF . OFF ]
[OFF . OFF ]
[OFF . OFF]
[OFF . OFF]
[OFF . OFF]
[OFF . OFF]
[OFF . OFF]
DVD/LD
TV/DVD
SAT
VIDEO
DVR/VCR1
VCR2
VCR3
( Next)
1
2
[ON . OFF ]
[OFF . OFF ]
[OFF . OFF]
[OFF . OFF]
[OFF . OFF]
[OFF . OFF]
[OFF . OFF]
CAUTION: If the "FIXED"
position is chosen,the
volume will be loud.
With the FIXED setting, the source is sent from this
receiver at maximum volume, so make sure the volume is
quite low in the sub room at first and then experiment to
find the correct level.
3
Select the type of IR receiver you’re using.
• PIONEER – Use this setting if you’re using a Pioneer
MR-100 (or if the IR receiver you’re using doesn’t
seem to work after selecting others).
• OTHERS – Use this setting for all other IR receivers.
• OFF · OFF – 12 volt triggers 1 and 2 are switched off.
3.7. Multi-Room Setting
• OFF · ON – 12 volt trigger 1 is switched off; 12 volt
trigger 2 is switched on.
Volume Level
[VARIABLE]
IR Receiver
[ OTHERS ]
[Return]
• ON · OFF – 12 volt trigger 1 is switched on; 12 volt
trigger 2 is switched off.
CAUTION: If the "FIXED"
position is chosen,the
volume will be loud.
• ON · ON – 12 volt triggers 1 and 2 are switched on.
3 Repeat for as many input functions as you would
like to set.
4 When you're finished, select RETURN and press
ENTER.
You will return to the Expert Setup menu.
Multi-Room Setting
4 Select ‘Return’ then press ENTER to finish.
You will return to the Expert Setup menu.
Note
• Some IR receivers may not work with this receiver.
Check with your audio dealer for more information.
• Default setting: VARIABLE / PIONEER
If you’ve made multi-room connections (see Multi-room
setup on page 83) you may need to specify your volume
setting and IR receiver type.
1
Select ‘Multi-Room Setting’ then press ENTER.
3.Expert Setup
[1. OSD Adjustment ]
[2. Bass Peak Level ]
[3. D-Range Control ]
[4. Function Rename ]
[5. OSD Overlay ]
[6. 12V Trigger ]
[7. Multi-Room Setting ]
[Return]
95
En
Advanced setup
11
THX Audio Setup
THX Ultra2 Subwoofer Setup
The settings in the THX Audio Setup menu allow you to
get optimum sound from the Home THX modes (on
page 45) if you’re using a subwoofer and surround back
speakers with your home theater system. See THX
speaker system setup on page 98 for more on this.
With some speaker setups, depending on the position of
the subwoofer and the walls in your listening area, you
may experience overly resonant frequencies in the bass.
If you have this problem use the THX Ultra2 subwoofer
setup to switch on boundary gain compensation (see
About THX® on page 109 for more on this).
To access the THX Audio Setup menu, follow the steps
below.
1 Make sure your receiver and TV are both
switched on.
2 Using the remote control, press RECEIVER on the
touch screen, then press the SYSTEM SETUP button.
RECEIVER
RECEIVER
INPUT 1
2
4 When you're finished, select RETURN and press
ENTER.
You will return to the THX Audio Setup menu.
3
DVD
/ LD
TV
/ DVD
SAT
DVR
/ VCR1
CD
TUNER
TV
CONT
MULTI
OPERATION
SYSTEM
OFF
Surround Back Speaker Position
SETUP
ENTER
CHANNEL
MENU
VOLUME
Note
AV AMPLIFIER
An on-screen display (OSD) appears on your TV. Use the
/// hard keys and ENTER on the remote control
to navigate through the screens and select menu items.
• The / (cursor up/down) hard keys select menu
items and the / (cursor left/right) hard keys
change the setting of the item selected.
Select ‘THX Audio Setup’ then press ENTER.
System Setup
[Auto Surround Setup]
[1.
[2.
[3.
[4.
Input Assign ]
Surround Setup ]
Expert Setup ]
THX Audio Setup ]
[Exit]
96
En
For the most effective results when using the THX Ultra2
Cinema and THX MusicMode listening modes (see Using
the Home THX modes on page 45) with the Advanced
Speaker Array (ASA) system (see About THX® on
page 109), it is required that you make the setting below.
MUTE
SYSTEM
SETUP
3
2 Specify whether your subwoofer is THX Ultra2
certified or not.
If your subwoofer isn’t THX Ultra2 certified, but you still
want to switch boundary gain compensation on, select
YES here, but the effect might not work properly.
3 Select either ON or OFF for the Boundary Gain
Compensation setting.
1/3
HOME
1 Select ‘Ultra2 SW Setup’ from the THX Audio
Setup menu.
• If you don't have surround back speakers, or just have
one, you won't be able to select this setting.
1 Select ‘SB SP Position’ from the THX Audio Setup
menu.
2 Specify the distance of your surround back
speakers from each other.
• 0–1 ft – Surround speakers within 1 foot apart (best
for THX surround sound).
• <1–4 ft – Surround speakers between 1 and 4 feet
apart.
• 4 ft< – Surround speakers more than 4 feet apart.
3 When you're finished, select RETURN and press
ENTER.
You will return to the THX Audio Setup menu.
Additional information
12
Chapter 12
Additional information
Optimizing your speaker setup
In addition to the speaker placement tips outlined in
Placing the speakers on page 27, you can use the
diagrams and explanations provided below as a
reference for optimum placement of each set of
speakers.
Basic surround setup
If you're using a center speaker, place the front speakers
at a wider angle. If not, place them at a narrower angle.
Surround and surround back speakers should be
positioned a foot-and-a-half to three feet (60 cm–90 cm)
higher than your ears and titled slight downward. Make
sure the speakers don't face each other. For DVD-Audio,
the speakers should be more directly behind the listener
than for home theater playback.
No surround back speakers
90~120
C
FR
FL
LS
RS
LS
RS
45~60
Make sure the center speaker does not cross the line
formed by the leading edge of the front left and right
speakers.
One surround back speaker
90~120
C
FR
FL
LS
RS
LS
RS
SB
It is best to angle the speakers towards the listening
position. The angle depends on the size of the room. Use
less of an angle for bigger rooms.
Two surround back speakers
C
FL
FR
RS
LS
0~60
SBL
SBL
SBR
SBR
97
En
12
Additional information
THX speaker system setup
If you have a complete THX speaker system, follow the
diagram below to place your speakers. Note that the
surround speakers ( indicates bi-polar radiating
speakers) should output at an angle parallel to the
listener.
FL
C
FR
LS
RS
Surround
Surround
SBL
SBR
Surround back
If you have two surround back speakers THX
recommends placing them together and the same
distance from your listening position so you can take
advantage of the ASA feature. For more details see
Advanced Speaker Array™ (ASA) on page 110.
See also THX Audio Setup on page 96 to make the settings
that will give you the best sound experience when using
the Home THX modes (on page 45).
Speaker system setup for DVD-Audio/
multichannel music sources
The best speaker placement for DVD-Audio (and other
multichannel music sources) may be different than for
regular DVD discs. For these formats, some sound
studios use the setup shown in the diagram below (as
recommended by ITU-R) instead of the setups in Basic
surround setup on page 97.
98
En
Note
• If you connect an alternate set of surround speakers,
you can use speaker system B to provide additional
surround sound options when listening to
multichannel music sources. See Alternating
surround speaker setups using speaker system B (ITUR) on page 80 for how to set it up.
• If you’re using two surround back speakers, you can
select the STANDARD SX listening mode during
DVD-Audio playback to simulate the sound achieved
from the setup shown in the diagram above. The
sound from the surround and surround back
speakers are combined to create a virtual surround
speaker.
Additional information
12
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Power
Symptom
Cause
The power does not turn on.
• The power plug is disconnected.
Remedy
• Connect the power plug to the wall outlet.
• The protection circuit may have been
activated.
• Disconnect the power plug from the outlet, and insert
again.
• Something is obstructing the rear panel fan. • Unplug the receiver from the wall and call a Pioneerauthorized independent service company.
The receiver suddenly switches
off.
• The speaker wires are frayed or sticking out • Reinsert the speaker wires, making sure there are no
of the jack, and are touching the back of the stray strands of wire and that they are inserted fully.
receiver or another set of wires.
• The receiver has a serious problem.
• Unplug the receiver from the wall and call a Pioneerauthorized independent service company.
During loud playback the power
suddenly switches off.
• The protection circuit has been activated
because the lowest actual impedance of the
speakers (as opposed to the speakers rated
impedance) is dangerously low.
• Turn down the volume.
• When its convenient, go to Acoustic Calibration EQ on
page 61 and lower the 63 Hz and 125 Hz equalizer levels
using the manual setting.
• Turning the digital safety feature on may allow you to
turn up the volume a little more. To switch between
SAFETY 1 (medium effect), SAFETY 2 (more effect) and
SAFETY OFF, put the receiver into standby, then press the
STANDBY/ON button while holding down the OPTION
button on the front panel. If the power switches off even
with SAFETY 2 switched on, turn down the volume.
AMP ERR blinks in the display,
then the power automatically
switches off.
• The receiver has a serious problem.
• After about a minute (you won’t be able to switch the
unit on during this time), switch the receiver back on. If
the message persists, call a Pioneer-authorized
independent service company.
FAN STOP blinks in the display,
then the power automatically
switches off.
• Something is obstructing the rear panel fan. • Remove the obstruction and try switching the receiver
back on. If the fan is still not working, or you can’t remove
the object, unplug the receiver from the wall and call a
Pioneer-authorized independent service company.
• The fan is malfunctioning.
OVERHEAT blinks in the display • The internal temperature of the unit has
and no sound is output.
become too high.
• Unplug the receiver from the wall and call a Pioneerauthorized independent service company.
• After allowing the unit to cool down in a well-ventilated
place, try switching the receiver back on. Make sure you
follow the guidelines for improving heat dispersal in
Ventilation on page 8.
99
En
12
Additional information
No sound
Symptom
Cause
Remedy
No sound is output when an
input source is selected.
• Improper connections.
• Make sure you have properly connected the component
to the corresponding input on the back of the receiver
(see Connecting your equipment on page 14).
• Sound is muted or the volume is turned
down.
• Press MUTE or adjust the volume accordingly.
• The TAPE 2 monitoring feature is on.
• Press TAPE 2 MONITOR to switch it off (see Monitoring
your recording on page 75).
• Speakers are turned off or selected
improperly with the SP SYSTEM A/B switch.
• Press SP SYSTEM A/B to select the proper speaker set
(see Switching the speaker system on page 80).
• The input signal type is incorrect.
• Press SIGNAL SELECT to select the proper input signal
(see Selecting the input signal type on page 48).
• The i.LINK source selected for the main
room has also been selected as a source in
the sub room.
• Choose a different source or choose a different input
signal for the main room, such as DIGITAL or ANALOG
(see Selecting the input signal type on page 48).
• The U-shaped connectors that connect the
POWER AMP IN terminals to the front
channel pre outs are not connected.
• Reconnect the POWER AMP IN terminals to the front
channel pre-outs using the supplied U-shaped connectors
(see item 8 in Rear panel on page 14).
• The front speakers are connected to the B
speaker system jack.
• Connect the front speakers to the A speaker system
jacks (see Installing your speaker system on page 26).
• Speaker settings are incorrect. (for
example, they have been set to NO).
• Check you speaker settings in Speaker Systems on
page 58.
• The surround and/or center levels are
turned down.
• Check the levels in Channel Level on page 60.
• The surround and/or center speakers are
disconnected.
• Check Installing your speaker system on page 26 to
make sure the speakers are connected correctly.
• The STEREO listening mode has been
selected.
• Choose a surround listening mode (see Listening in
surround sound on page 43).
• Speaker system B is selected.
• Select speaker system A (see Switching the speaker
system on page 80).
• The 2 channel input setting is selected
when using the multichannel analog inputs
or the USB interface.
• Change the setting accordingly (see Selecting USB and
multichannel analog input channels on page 49).
• Surround back speakers are set to NO.
• Set the surround back speakers to LARGE or SMALL
(see Speaker Systems on page 58).
• The SB CH mode is switched off.
• Set the surround back channel to SB CH ON (see
page 50).
• The source is not a 6.1 channel playback
source.
• Choose an Advanced surround listening mode (see
Listening in surround sound on page 43).
• The surround back speakers are
disconnected.
• Check Installing your speaker system on page 26 to
make sure the speakers are connected correctly.
• The surround back channel is on the 1
speaker setting, and your speaker is
connected to the right channel output.
• Connect the speaker to the surround back left channel
output (Installing your speaker system on page 26).
• The wrong input setting is selected when
using the multichannel analog inputs or the
USB interface.
• Change the setting accordingly (see Selecting USB and
multichannel analog input channels on page 49).
No sound output from the front
speakers.
No sound from the surround or
center speakers.
No sound from surround back
speakers.
• The SB CH MODE is switched to AUTO and • You can still listen with surround back sound by setting
the Dolby Surround EX / DTS ES software
the surround back channel to SB CH ON (page 50).
you’re playing has no flag to indicate it is 6.1
compatible.
100
En
Additional information
12
Symptom
Cause
No sound from subwoofer.
• The subwoofer is disconnected or switched • Connect or switch on the subwoofer (see Installing your
off.
speaker system on page 26).
• The subwoofer's settings are incorrect.
Remedy
• Set the subwoofer (see Speaker Systems on page 58).
• Set the front speakers to SMALL (see Speaker Systems
on page 58).
No sound from one speaker.
The program indicator lights for
a channel, but no sound is
output from the corresponding
speaker.
• The crossover frequency is set too low.
• Set the crossover frequency to a (higher) frequency that
matches your speaker characteristics (see Speaker
Systems on page 58)
• The bass attenuator is set too low.
• See Bass Peak Level on page 93 to adjust the setting.
• The subwoofer's levels are too low.
• See Channel Level on page 60 to check the speaker
levels.
• Check the volume control on the subwoofer to make
sure it is turned up.
• The speaker setting has been set to NO.
• Change the setting in Speaker Systems on page 58.
• The speaker level is too low.
• Check the level in Channel Level on page 60.
• The speaker isn’t connected properly.
• Check Installing your speaker system on page 26 to
make sure the speaker is connected correctly.
• The source has no sound output for that
channel.
• By choosing an Advanced surround listening mode (see
Listening in surround sound on page 43), you may be able
to create an extra channel for the speaker.
• A mute signal is recorded on the channel.
Sound is produced from analog • The digital input assignment is wrong.
components, but not from digital
ones (DVD, LD, CD-ROM etc.).
• The digital components aren't connected
properly.
• Assign the digital inputs correctly (see Assigning the
digital inputs on page 90).
• Make sure you have properly connected the digital
component to the corresponding input on the back of the
receiver (see Connecting your equipment on page 14).
• The player is not compatible with the source • Choose a compatible source, or check the component’s
you're using, or the player settings are
manual for the correct settings.
incorrect.
• The digital output level has been turned
• Set the digital volume level of the player to full, or to the
down on a CD player or other component
neutral position.
equipped with digital output level adjustment
capability.
• Analog input has been selected.
• Select digital input (see Selecting the input signal type
on page 48).
When playing an LD the input
signal type is 2RF but there is
still no sound.
The LD is not a Dolby Digital compatible disc. • Set the input signal to AUTO (see Selecting the input
signal type on page 48). Also make sure your LD player is
hooked up with analog connections in addition to digital
and 2RF connections (see Connecting other video
sources on page 21).
No sound output from the
headphones.
The U-shaped connectors that connect the
POWER AMP IN terminals to the front
channel pre-outs are not connected.
• Reconnect the POWER AMP IN terminals to the front
channel pre-outs using the supplied U-shaped connectors
(see item 8 in Rear panel on page 14).
No sound is output or a noise is
output when Dolby Digital/DTS
software is played back.
• A DVD player not compatible with Dolby
Digital/DTS is being used.
• Make sure your DVD player is compatible with Dolby
Digital/DTS.
• The settings on the DVD player are incorrect • Make sure the player's settings are correct and/or the
and/or the DTS signal output is turned off.
DTS signal out is on. Refer to the instruction manual
supplied with the DVD player.
• The digital output level is turned down on a • Set the digital volume level of the player to full, or to the
CD player or other component equipped with neutral position.
digital output level adjustment capability. (The
DTS signal has been altered by the player, and
cannot be read.)
No sound is output when the
AM/FM is selected.
• Incorrect frequency.
• Tune into the correct frequency.
• The antenna is not connected.
• Connect the antenna (see Connecting antennas on
page 28).
101
En
12
Additional information
Symptom
Cause
Remedy
No digital output from the DVD
player when playing a
multichannel DVD-Audio or
SACD disc.
• DVD players do not output digital audio
when playing these kinds of discs.
• To enjoy fully multichannel DVD-Audio and SACD discs,
connect your DVD player to this receiver through the
multichannel analog inputs. See Connecting the
multichannel analog outputs on page 18 and also the
operating instructions that came with your DVD player.
No digital output when playing a • DVD players do not output digital audio at
192/176.4 kHz sampling rate
these sampling rates. Usually, players output
DVD-Audio disc.
the audio from these discs at a downsampled
rate of 96/88.2 kHz or 48/44.1 kHz. Some discs
prohibit all digital output.
• This is not a malfunction. To enjoy fully these discs,
connect your DVD player to this receiver through the
multichannel analog inputs. See Connecting the
multichannel analog outputs on page 18 and also the
operating instructions that came with your DVD player.
During playback of a Dolby
Surround EX / DTS ES
soundtrack, the LS, S and RS
indicators light but there is no
surround back channel sound.
• The listening mode is not set correctly.
• Set the surround back channel to SB CH AUTO (see
Using the surround back channel on page 50).
Symptom
Cause
Remedy
Broadcast stations cannot be
selected automatically, or there
seems to be considerable noise
in radio broadcasts.
FM broadcasts
• The FM antenna is not fully extended or is
poorly positioned.
• Fully extend the FM wire antenna, position for best
reception, and secure to a wall.
• Weak radio signals.
• Connect an outdoor FM antenna (see page 28).
Other audio problems
AM broadcasts
• The AM antenna is poorly positioned.
• Adjust the direction and position for best reception.
• Weak radio signals.
• Connect an additional internal or external AM antenna
(see page 28).
• Interference caused by other equipment
(fluorescent lamp, motor, etc.).
• Turn off the equipment causing the noise or move it
away from the receiver.
• Place the antenna farther away from the equipment
causing the noise.
Noise is output when scanning a • The scan function performed by the player
DTS CD.
slightly alters the digital information, making
it unreadable.
• This is not a malfunction, but be sure to turn the volume
down to prevent the output of loud noise from your
speakers.
When playing a 96 kHz/24bit disc • Different discs have different recording
the sound is too loud.
levels so some may be louder than others.
• Turn the volume down.
When playing a DTS format LD
there is audible noise on the
soundtrack.
• The input signal type is set to ANALOG.
• Set the input signal type to DIGITAL (see Selecting the
input signal type on page 48)
Can't record audio.
• You are trying to make an analog recording •You can only record analog to analog, or digital to digital.
from a digital signal, or a digital recording of
an analog source.
• The digital source is copy protected.
• You can't record digital sources that have been copy
protected.
• The analog REC jacks have not been
connected properly.
• Check your analog connections (see Connecting analog
audio sources on page 24).
The sound distorts and/or the
OVER indicator won’t stop
lighting.
• The analog signal is too strong.
• Turn on input attenuator (see Reducing the level of an
analog signal on page 76).
• If the source has an analog output setting, lower it as
necessary.
You can only hear treble from
speakers.
• The front speakers are set to SMALL.
• Set the front speakers to LARGE (see Speaker Systems
on page 58).
Subwoofer output is very low.
• The speaker settings result in very little
audio signal being sent to the subwoofer.
• To route more audio signal to the subwoofer, set it to
PLUS, or select SMALL for the front speaker setting (see
Speaker Systems on page 58).
Everything seems to be set up
• The speakers are out of phase.
correctly, but the playback sound
is odd.
• Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding
terminals on the speakers (page 26).
Noise or hum can be heard even • There is electrical interference from another • Check that personal computers or other digital
when there is no sound being
component or appliance.
components connected to the same power source are not
input.
causing interference.
102
En
Additional information
12
Video
Symptom
Cause
Remedy
No image is output when an
input is selected.
• The video connections are incorrect.
• Make sure the video component is connected correctly
(see pages 17–21).
• You are using component video
connections for your source, but not for your
TV.
• Using the video converter, video signals can be
converted from a composite or S-video input to a
component video output, but not vice-versa. See About the
video converter on page 22 for more on this.
• You are using component video
• Check Assigning the component video inputs on page 91
connections and the component video inputs to make sure you’re assigned the correct input.
are assigned incorrectly.
• The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied
with the DVD/video player.
• The video input selected on the TV monitor
is incorrect.
• Set correctly. Refer to the instruction manual supplied
with the TV.
• The MONITOR OUT jack hasn't been
connected.
• Connect the MONITOR OUT jack to the TV monitor (see
Connecting your TV on page 16).
• Some TVs connected to the receiver with
component video cords do not display the
System Setup screen when the Color Burst
feature is on.
• When the receiver is in standby, switch to COLOR
BURST OFF by holding down the VIDEO SELECT button
and pressing STANDBY/ON. (the current setting
appears in the display). The multi-room control must be
switched off to do this.
Color noise appears on the
System Setup screen.
• Some TVs connected to the receiver with
composite video cords display color noise on
the System Setup screen when the Color
Burst feature is off.
• When the receiver is in standby, switch to COLOR
BURST ON by holding down the VIDEO SELECT button
and pressing STANDBY/ON (the current setting
appears in the display). The multi-room control must be
switched off to do this.
Overlay information doesn’t
appear on your TV or monitor.
• Overlay information doesn’t appear when
you are using different types of video cords for
source and TV connections, or when using
component video connections.
• Do not use component video cables if you would like to
see overlay information and use the same type of video
cable (for example, only composite, or only S-video) for
both source and TV connections.
Can’t see or hear television
programs.
• The video input selected on the TV monitor
is incorrect.
• Set the TV input to the channel you want to watch,
instead of the receiver input.
There is residual screen noise
after an overlay message
disappears.
• Some TVs exhibit this display problem.
• This is not a malfunction with this receiver.
Can’t record video.
• You are trying to record a source connected • Connect the source component to either the composite
to the component video jacks.
video or the S video jacks (see Connecting your equipment
on page 14).
The System Setup screen
doesn't appear.
• The source is copy protected.
• You can't record sources that have been copy protected.
Symptom
Cause
Remedy
The Auto Surround Setup
continually shows an error.
• The ambient noise level in the room is too
high.
• Keep the noise level in the room as low as possible
when using the Auto Surround Setup. If the noise cannot
be kept low enough, you will have to set up the surround
sound manually (page 57).
After using the Auto Surround
Setup, the subwoofer distance
setting is set further than the
actual measured distance.
• The low-pass filter found in subwoofers can • This is not a malfunction. The Auto Surround Setup has
introduce a delay in the playback sound.
compensated for the delay caused by the filter.
After using the Auto Surround
Setup, the speaker size setting
(LARGE or SMALL) is incorrect.
• There was some inaudible low-frequency
noise in the room.
• The low-frequency noise could have been caused by an
air conditioner or motor. Switch off all appliances in the
room and rerun the Auto Surround Setup.
The display shows KEY LOCK
ON when you try to make
settings.
• Your Pioneer dealer has enabled the key
lock feature.
• Ask your Pioneer dealer to disable the key lock.
Settings
103
En
12
Additional information
Remote control
Symptom
Cause
Remedy
The receiver cannot be remote
controlled.
• You are too far away or at a bad angle for
operation.
• Operate within 23 ft., 30° of the remote sensor on the
front panel (see Using the remote control on page 9).
• There is an obstacle between the receiver
and the remote control.
• Remove the obstacle or operate from another angle of
position.
• Strong light such as fluorescent light.
• Avoid exposing the remote sensor on the front panel to
direct light.
• The remote control has a weak charge.
• Recharge the remote control (see Recharging the remote
control on page 9). You can also use the remote while it’s
placed on the recharger.
• The remote control is locked.
• Unlock the remote control (see Locking the remote
control on page 12).
• The CONTROL IN jack has been hooked up. • Disconnect the CONTROL IN jack (see Operating other
Pioneer components with this unit’s sensor on page 74).
Other components cannot be
remote controlled.
• The IR-receiver does not correspond with
the type specified in the multi-room settings.
• Change the setting to correspond with your IR-receiver
(Multi-Room Setting on page 95).
• The proper code hasn't been input into the
remote control to control that component.
• Input the proper code into the remote control (see
page 67).
• Something is plugged into the CONTROL IN • Either point remote at the remote sensor of the unit that
jack.
is plugged into the CONTROL IN jack or unplug the cable
from the CONTROL IN jack and use remote normally (see
Operating other Pioneer components with this unit’s
sensor on page 74).
The remote control doesn’t seem • The remote control hasn’t been seated
to recharge properly (the
properly on the recharger.
recharge indicator doesn’t light),
or it won’t hold a charge.
• The battery cells need to be replaced.
• Reseat it on the recharger, making sure to align the
indent on the bottom of the remote with the tabs on the
recharger.
The remote control display is
flashing LOW BATTERY or is
blank.
• The remote control needs to be recharged.
• Place the remote control on the recharger. If the remote
hasn’t been charged for awhile, the remote control display
may remain blank for several minutes before the touch
screen appears. See Recharging the remote control on
page 9 for more on this.
The remote control display is
blank or very hard to see.
• The remote control contrast needs to be
adjusted.
• Use the contrast control on the right-hand side of the
remote to adjust the contrast as necessary.
• See Replacing the lithium-ion batteries on page 12.
• The remote control backlight is switched on • Switch the backlight off.
in a bright room.
When you press an input select • The Direct Function feature for the
• See Remote Direct function on page 70 to switch it on
button on the Home menu
component you want to select is switched off. again.
screen, the receiver input source
doesn’t change to the selected
function.
Can’t program certain buttons
with remote signals when using
the learning feature.
The display changes after
selecting a button when using
the learning feature.
• You have selected a button that cannot
learn commands.
• Select another button that can learn commands (see
Programming signals from other remote controls on
page 69).
• You have already selected a button for
learning.
• Press the same button again to deselect it or press END
to go back a screen (see Programming signals from other
remote controls on page 69).
• You have selected a button that accesses a • These buttons cannot be programmed (see
menu.
Programming signals from other remote controls on
page 69).
The SR cable is connected, but • The SR cable hasn't been connected
the connected components can’t properly.
be operated with the remote.
• The rest of the component connections
have not been made.
• Reinsert the SR cable, making sure it’s connected to the
right jack (see Operating other Pioneer components with
this unit’s sensor on page 74).
• Make sure an analog connection has been made
between the units.
• The component you have hooked up is not a • This feature only works with Pioneer products.
Pioneer product.
The remote control touch screen • The remote control display has frozen
doesn’t respond.
(stopped operating).
104
En
• Restart the remote control (see Restarting the remote
control on page 12).
Additional information
Symptom
Cause
The date and time have suddenly • The remote control is low on batteries and
changed.
reset the date automatically.
12
Remedy
• Reset the clock (see Setting the clock on page 10).
• The date was cleared after restarting the
remote control.
• Reset the clock (see Setting the clock on page 10).
Symptom
Cause
Remedy
The display is dark or off.
• The display is set to dark or off.
• Press DIMMER on the remote control repeatedly to
select a different brightness.
After making an adjustment the
display goes off.
• The display is set to off.
• Press DIMMER on the remote control repeatedly to
select a different brightness.
Display
You can't get DIGITAL or 2RF to • There is a problem with the digital
display when using the SIGNAL connections or the digital input is assigned
SELECT button.
incorrectly.
• Check your digital connections and/or assign the digital
inputs correctly (see Assigning the digital inputs on
page 90).
• The TAPE 2 monitoring feature is on.
• Press TAPE 2 MONITOR to switch it off (see Monitoring
your recording on page 75).
• You’ve selected an unassigned i.LINK
source input.
• Select the correct source input or assign your i.LINK
connections correctly (see Assigning the i.LINK inputs on
page 91).
The Dolby/DTS indicator doesn't
light when playing Dolby/DTS
software.
• The player is paused.
• Press play.
• The player's sound output settings are
wrong.
• Set the player correctly (consult the manual that came
with the player, if necessary).
When playing a DVD-Audio CD,
the DVD player display shows 96
kHz. However, the receiver’s
display does not.
• The audio from these discs is output from
• This is not a malfunction. See also the operating
the analog audio jacks of the DVD player only; instructions that came with your DVD player.
the receiver does not show the sampling rate
of the input signal through the analog inputs.
During playback of a DTS 96/24 • The source is being downsampled.
source, the display doesn't show
96kHz.
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light.
• See Listening to dual mono soundtracks on page 53 for
several different ways listen to sources without
downsampling.
• One of the DIGITAL NR, MIDNIGHT or
LOUDNESS features are switched on.
• Turn it/them off by pressing the corresponding button
on the remote control or front panel.
• No digital connection, or the digital
connection is incorrect.
• Check the digital audio connection (page 17).
• The receiver’s input signal type is set to
analog.
• Set the receiver to AUTO or DIGITAL (see Selecting the
input signal type on page 48).
• The DVD player is set to output Dolby Digital • Check the settings on the player. Set the output for
and/or DTS audio as PCM.
Dolby Digital and DTS (no PCM conversion). See also the
operating instructions that came with your DVD player.
• The disc has several playback audio tracks; • Switch the playback audio channel on your DVD player.
the one currently playing is actually PCM.
See the operating instructions that came with your DVD
player.
When playing certain discs,
none of the receiver’s format
indicators light.
• The audio format of the disc is not 5.1/6.1
channel.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
When playing a disc, the
2 Pro Logic II or Neo:6
indicator lights on the receiver.
• The input signal type is set to analog.
• Set the receiver to AUTO or DIGITAL (see Selecting the
input signal type on page 48).
• A 2 channel soundtrack is currently playing. • This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• The soundtrack currently playing is
encoded using Dolby Surround.
During playback of a Surround
•The source may be Dolby Surround EX / DTS
EX or DTS ES source on the
ES software, but it has no flag to indicate it is
Stream Direct or SB CH AUTO
6.1 compatible.
setting, the EX and ES indicators
don’t light, or the signal is not
properly processed.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• Switch the surround back channel setting (page 50) to
SB CH ON then switch to the THX Surround EX or
Standard EX listening mode (see Listening in surround
sound on page 43).
105
En
12
Additional information
i.LINK interface
Symptom
Cause
Remedy
No sound is output.
• An output signal is not produced from the
i.LINK connector on the source player.
• Refer to the manual that came with the source player.
• The selected component is not compatible
with i.LINK audio.
• Refer to the manual that came with the source player.
• The input signal is set to 2RF, DIGITAL or • Select i.LINK or AUTO using the SIGNAL SELECT
ANALOG.
button (see Selecting the input signal type on page 48).
i.LINK indicator does not light up • The 2RF, DIGITAL or ANALOG input
even when an i.LINK-equipped
signal is selected.
component is selected.
• Select i.LINK or AUTO using the SIGNAL SELECT
button (see Selecting the input signal type on page 48).
The program format indicators
don’t disappear when SACD
playback stops.
• This is not a malfunction.
• The program format indicators remain lit
until another format source is input.
You cant get i.LINK to display
• i.LINK-equipped component(s) are not
when using the SIGNAL SELECT ready.
button.
• i.LINK input setting is incorrect.
After upgrading a component, it
is not recognized and cannot be
selected using the i.LINK
connection.
• Turn on the component(s).
• Select the correct i.LINK input setting (see Assigning
the i.LINK inputs on page 91).
• Depending on the upgrade process, certain • You may need to reset the i.LINK database memory in
components may cease to be recognized by the receiver:
the receiver.
With the receiver in standby, press STANDBY/ON
while holding down OPTION+. When you see DB CLEAR?
appear in the display, press OPTION–, then OPTION+
again to confirm. When you’ve reset the i.LINK database
memory, DB CLEAR SET shows in the display.
i.LINK messages
You may see the following messages displayed in the front panel display when using the i.LINK interface.
106
En
Message
Explanation
BUS FULL
The i.LINK bus has reached its capacity and cannot transmit any more data.
CANNOT LINK 1
The connection between the receiver and the selected i.LINK-equipped component is unstable. If the
i.LINK cables appear to be connected properly and both the receiver and i.LINK-equipped component are
on, switch both units off, then on again to re-establish the connection between them.
CANNOT LINK 2
The receiver can’t identify the selected i.LINK-equipped component. For example, the receiver may not be
able to identify an i.LINK-equipped personal computer.
LINK CHECK
The receiver is checking the i.LINK network. It does this when components are added to, or removed from
the network. The sound may be interrupted if this happens during playback.
LOOP CONNECT
The i.LINK network cannot function because the connected components form a loop. See Creating an
i.LINK network on page 86 for more on this.
NO NAME
When an i.LINK-equipped component has no name, this message is displayed instead of the proper
component name.
NO SIGNAL
A component is outputting an i.LINK signal that the receiver cannot reproduce. This receiver can only
reproduce signals from i.LINK-Audio-equipped components. See About i.LINK on page 86 for more on
this.
PQLS OFF
This is displayed when PQLS turns off during playback. The sound may be interrupted momentarily when
this happens.
PQLS ON
This is displayed when PQLS turns on during playback. The sound may be interrupted momentarily when
this happens.
UNKNOWN
When an i.LINK-equipped component name cannot be recognized, this message is displayed instead of
the proper component name.
Additional information
12
USB interface
Symptom
Cause
Remedy
No sound.
• The computer settings are incorrect.
• Make sure you have set up your computer system to
output through the USB interface (see Using the USB
interface on page 87).
• The software or source material you are
using is not compatible with USB output.
• Update to a more recent version of your existing
software, try a different audio program, or try a different
source.
• The volume control on your computer is set • Turn up the volume on your computer.
too low.
No sound from one or more
channels.
• The software settings are incorrect, or the
program you are using cannot output
multichannel audio.
• Try changing the software settings. If this doesn’t work,
update to a more recent version of your existing software,
or try a different audio program.
• The wrong input setting is selected for the
USB interface.
• Change the setting accordingly (see Selecting USB and
multichannel analog input channels on page 49).
Symptom
Cause
Remedy
The receiver doesn’t seem to
respond when the buttons are
pressed.
• Static electricity caused by dry air.
• Switch the power off then on again. If this doesn’t seem
to work, try disconnecting the power plug from the outlet,
and insert again.
One of the Home THX 7.1
channel modes is selected, but
there are certain options that
can't be chosen.
• There is only one surround back speaker
• Make sure there are two surround back speakers
connected or the current settings are for only connected (see Connecting the speakers on page 26) and
one surround back speaker.
make the necessary settings in Speaker Systems on
page 58.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• The subwoofer channel can be delayed
slightly if run through a low-pass filter.
• See Automatically setting up for surround sound on
page 39 to set up your system again using MCACC (this
will automatically compensate for a delay in the
subwoofer output).
The receiver doesn’t memorize
the last volume level you used
before switching it off.
• The receiver was switched off immediately
after changing the volume level.
• Make sure to switch off the receiver two seconds or
more after changing the volume.
The receiver doesn’t memorize
the last adjustments you made
before switching it off.
• The receiver was switched off immediately
after changing the receiver status.
• Make sure to switch off the receiver two seconds or
more after changing the receiver status.
Miscellaneous
Note
• If the unit does not operate normally due to external
effects such as static electricity, disconnect the
power plug from the outlet and insert again to return
to normal operating conditions.
107
En
12
Additional information
Surround sound formats
Below is a brief description of the main surround sound
formats you’ll find on DVDs, satellite, cable and
terrestrial broadcasts, and video cassettes.
Dolby
The Dolby technologies are explained below. See
www.dolby.com for more detailed information.
Dolby Surround is an encoding system which embeds
surround sound information within a stereo soundtrack,
which a Dolby Pro Logic decoder can then use for
enhanced surround listening with greater sound detail.
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic", “Surround EX” and the double-D
symbol are trademarks of Dolby Laboratories.
DTS
The DTS technologies are explained below. See
www.dtstech.com for more detailed information.
Dolby Digital
Dolby Digital is a multichannel digital audio coding
system widely used in cinemas, and in the home for DVD
and digital broadcast soundtracks. It can deliver up to six
discrete audio channels, comprising five full range
channels and a special LFE (low frequency effects)
channel used mainly for deep, rumbling sound effects;
hence the term “5.1-channel” Dolby Digital.
In addition to the format features above, Dolby Digital
decoders offer downmixing for compatibility with mono,
stereo and Dolby Pro Logic audio from a number of bit
rates and channels. Another feature, called Dialog
Normalization, attenuates programs based on the
average level of dialog in a program relative to its peak
level (also known as Dialnorm) in order to achieve
uniform playback level.
Dolby Digital Surround EX
Dolby Digital Surround EX (the EX stands for EXtended)
is an extension of Dolby Digital encoding whereby a
surround back channel is matrixed into the surround left/
right channels for 6.1 channel playback. This allows for
compatibility with Dolby Digital 5.1 channel decoding, as
well as for pure decoding using Dolby Digital EX.
Dolby Pro Logic IIx and Dolby Surround
Dolby Pro Logic IIx is an improved version of the Dolby
Pro Logic II (and Dolby Pro Logic) decoding system. Using
the innovative “steering logic” circuit, this system
extracts surround sound from sources as follows:
• Dolby Pro Logic – 4.1 channel sound (mono
surround) from any stereo source
• Dolby Pro Logic II – 5.1 channel sound (stereo
surround) from any stereo source
• Dolby Pro Logic IIx – 6.1 or 7.1 channel sound
(stereo surround and surround back) from two
channel or 5.1 channel sources
With two channel sources, the “.1” subwoofer channel is
generated by bass management in the receiver.
108
En
DTS Digital Surround
DTS Digital Surround is a 5.1-channel audio coding
system from Digital Theater Systems Inc. now widely
used for DVD-Video, DVD-Audio, 5.1 music discs, digital
broadcasts, and video games. It can deliver up to six
discrete audio channels, comprising five full range
channels, including an LFE channel. Higher sound
quality is achieved through the use of a low compression
rate, and high rates of transmittance during playback.
DTS-ES
DTS-ES (the ES stands for Extended Surround) is a
decoder that is capable of decoding both DTS-ES
Discrete 6.1 and DTS-ES Matrix 6.1 encoded sources.
DTS-ES Discrete 6.1 gives ‘true’ 6.1 channel sound, with
a completely separate (discrete) surround back channel.
DTS-ES Matrix 6.1 has a surround back channel matrixed
into the surround left/right channels. Both sources are
also compatible with a conventional DTS 5.1 channel
decoder.
DTS Neo:6
DTS Neo:6 can generate 6.1 channel surround sound
from any matrixed stereo source (such as video or TV)
and from 5.1 channel sources. It uses both the channel
information already encoded into the source, as well as
its own processing to determine channel localization
(with two channel sources, the “.1” subwoofer channel is
generated by bass management in the receiver). Two
modes (Cinema and Music) are available using DTS
Neo:6 with two channel sources.
Additional information
12
DTS 96/24
THX Cinema™ processing
DTS 96/24 is an extension of the original DTS Digital
Surround which offers high quality 96 kHz / 24-bit audio
using a DTS 96/24 decoder. This format is also fully
backward compatible with all existing decoders. This
means that DVD players can play this software using a
conventional DTS 5.1 channel decoder.
THX engineers developed patented technologies to
accurately translate the sound from the movie theater
environment into the home, correcting the tonal and
spatial errors that occur. When the THX indicator shows
in the display, THX features are automatically added in
Cinema modes (see Using the Home THX modes on
page 45).
“DTS”, “DTS-ES Extended Surround”, “DTS 96/24” and
“Neo:6” are trademarks of Digital Theater Systems, Inc.
Windows Media® Audio 9 Professional
Windows Media® Audio 9 Professional (WMA9 Pro) is a
discrete surround format developed by Microsoft
Corporation.
Re-Equalization™
The tonal balance of a film soundtrack will be excessively
bright and harsh when played back over audio
equipment in the home because film soundtracks were
designed to be played back in large movie theaters using
very different professional equipment. Re-Equalization
restores the correct tonal balance for watching a movie
soundtrack in a small home environment.
Timbre Matching™
WMA9 Pro can support up to 5.1/7.1 channel playback
with sampling rates up to 24-bit/96kHz. Using the unique
WMA compression techniques, WMA9 Pro can deliver
multichannel music and soundtracks over high-speed
internet networks at low bit rates with minimal audio
degradation. Playback may be enjoyed with the Windows
Media® Player 9 Series (or other third-party media player)
on a personal computer, or with an AV amplifier with onboard WMA9 Pro decoding.
Windows Media® and the Windows logo are trademarks or
registered trademarks of Microsoft Corporation in the
United States and/or other countries.
This feature filters the sound going to the surround
speakers so that it more closely matches the sound
coming from the front speakers. This ensures seamless
panning between the front and surround speakers.
Adaptive Decorrelation™
By slightly changing one surround channel's time and
phase relationship with respect to the other surround
channel, Adaptive Decorrelation expands the listening
position and creates the same spacious surround
experience as in a movie theater using only two speakers.
THX Ultra2™
PCM (also known as Linear PCM) is a digital audio
coding system that does not use compression to reduce
the amount of data needed to represent the analog audio.
PCM audio can be found on CDs and some DVDs.
Before any home theater component can be THX Ultra2™
certified, it must incorporate all the features described
here and also pass a rigorous series of quality and
performance tests. THX Ultra2™ requirements cover
every aspect of the product including pre-amplifier
performance and operation, and hundreds of other
parameters in both the digital and analog domain.
About THX®
THX Surround EX™
PCM (Pulse Code Modulation)
THX is an exclusive set of standards and technologies
established by the world-renowned film production
company, Lucasfilm Ltd. These were designed to make
film soundtracks, in both movie theaters and in your
home theater, as faithful as possible to what the director
intended.
THX Surround EX-Dolby Digital Surround EX is a joint
development of THX Ltd. and Dolby Laboratories, Inc.
This technology reproduces an additional surround back
channel, bringing greater depth, spacious ambience,
sound localization and detailed imaging behind the
listener.
The THX technologies are explained below. See
www.thx.com for more detailed information.
This product may also engage the THX Surround EX
mode during the playback of 5.1 channel material that is
not Dolby Digital Surround EX encoded. In such case the
information delivered to the surround back channel may
have unpredictable results.
109
En
12
Additional information
Advanced Speaker Array™ (ASA)
When you set up your home theater system using all
eight speaker outputs and the two surround back
speakers are placed close together as shown in the
diagram in THX speaker system setup on page 98, the
surround sound experience is optimized for THX Ultra2™
Cinema and THX MusicMode.
THX's ASA circuitry will automatically detect DTS-ES
(Matrix and 6.1Discrete) and Dolby Digital Surround EX
encoded soundtracks for correct playback using all 8
speakers.
Please note that some Dolby Digital Surround EX
soundtracks are missing the digital flag that allows ASA
to switch automatically. Therefore, if you know that the
movie that you are watching is encoded in Surround EX,
you may manually select the THX Surround EX playback
mode.
THX Ultra2™ Cinema mode
This mode plays 5.1 movies using all 8 speakers giving
you the best possible movie watching experience. In this
mode ASA processing blends the side surround
speakers and back surround speakers giving you the
optimal mix of ambient and directional surround sounds.
THX MusicMode™
ASA technology optimizes playback of 5.1 encoded
music sources such as DTS and Dolby Digital using all 8
speakers in your setup.
Boundary Gain Compensation™
Depending on the listener’s and the subwoofer’s
position, the listener may experience an excessive bass
effect. This feature compensates for excessive bass
resulting from a boundary gain effect. This feature is
designed to operate when used with a subwoofer
certified to THX Ultra2™ specifications.
THX and Ultra 2 are trademarks or registered trademarks of
THX Ltd. Surround EX is a jointly developed technology of
THX Ltd. and Dolby Laboratories, Inc. and is a trademark of
Dolby Laboratories, Inc. Used under authorization. All
rights reserved.
Maintenance of external surfaces
• Use a polishing cloth or dry cloth to wipe off dust and
dirt.
• When the surfaces are dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six
times with water, and wrung out well, and then wipe
again with a dry cloth. Do not use furniture wax or
cleaners.
• Never use thinners, benzine, insecticide sprays or
other chemicals on or near this unit, since these will
corrode the surfaces.
110
En
Additional information
Specifications
Amplifier section
Continuous average power output of 160 watts* per
channel, min., at 6 ohms, from 20 Hz to 20,000 Hz with
no more than 0.09%** total harmonic distortion (front).
Continuous Power Output (6 Ω)
Front. . . . . . . . . . . . . 160 W + 160 W (20 Hz-20 kHz, 0.09%)
Center . . . . . . . . . . . . . . . . . . . 160 W (20 Hz-20 kHz, 0.09%)
Surround . . . . . . . . . 160 W + 160 W (20 Hz-20 kHz, 0.09%)
Surr. back . . . . . . . . 160 W + 160 W (20 Hz-20 kHz, 0.09%)
Continuous Power Output (8 Ω)
Front. . . . . . . . . . . . . 130 W + 130 W (20 Hz-20 kHz, 0.09%)
Center . . . . . . . . . . . . . . . . . . . 130 W (20 Hz-20 kHz, 0.09%)
Surround . . . . . . . . . 130 W + 130 W (20 Hz-20 kHz, 0.09%)
Surr. back . . . . . . . . 130 W + 130 W (20 Hz-20 kHz, 0.09%)
Audio Section
Input (Sensitivity/Impedance)
PHONO MM . . . . . . . . . . . . . . . . . . . . . . . . 4.7 mV/47 kΩ
LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 mV/47 kΩ
Phono Overload level (T.H.D.0.1%, 1kHz)
PHONO MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mV
Frequency Response
PHONO MM . . . . . . . . . . . .20 Hz to 20,000 Hz ± 0.3 dB
LINE. . . . . . . . . . . . . . . . . . . . . .5 Hz to 100,000 Hz dB
Output (Level/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 mV/2.2 kΩ
Tone Control
BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (100 Hz)
TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz)
LOUDNESS. . . . . . . . . . . . . . +4/+2 dB (100Hz/10 kHz)
(at volume position -40dB)
Signal-to-Noise Ratio (IHF, short circuited, A network)
PHONO MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 dB
LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
PHONO MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 dB
LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 dB
* Measured pursuant to the Federal Trade Commission’s
Trade Regulation rule on Power Output Claims for Amplifiers
** Measured by Audio Spectrum Analyzer
Video Section
Input (Sensitivity/Impedance) . . . . . . . . . . . . . . 1 Vp-p/75 Ω
Output (Level/Impedance) . . . . . . . . . . . . . . . . . 1 Vp-p/75 Ω
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB
Frequency Response . . . . . . . . . . . . . 5 Hz to 10 MHz dB
12
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB
Frequency Response . . . . . . . . . . . . . 5 Hz to 100 MHz dB
FM Tuner Section
Frequency Range . . . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Usable Sensitivity . . . . . .Mono: 13.2 dBf, IHF (1.3 µV/75 Ω)
50 dB Quieting Sensitivity . . . . . . . . . . . . . . Mono: 20.2 dBf
Stereo: 38.6 dBf
Signal-to-Noise Ratio . . . . . . . . . . . Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Distortion . . . . . . . . . . . . . . . . . . . . . . . . Stereo: 0.5% (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . .60 dB (400 kHz)
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . .40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . 30 Hz to 15 kHz ± 1dB
Antenna Input . . . . . . . . . . . . . . . . . . . . . . 75 Ω unbalanced
AM Tuner Section
Frequency Range . . . . . . . . . . . . . . . . 530 kHz to 1,700 kHz
Sensitivity (IHF, Loop antenna) . . . . . . . . . . . . . . . 350 µV/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Miscellaneous
Power Requirements. . . . . . . . . . . . . . . . . . .AC 120 V, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . 735 W, 970 VA
Power Consumption in Standby mode . . . . . . . . . . . 0.65 W
AC Outlet
SWITCHED . . . . . . . . . . . . . . . . . . . . 100 W (0.8 A) MAX
Dimensions . . . . . . . . . . . . 440 (W) × 204 (H) × 476 (D) mm
(17-5/16 (W) × 8 (H) × 18-3/4 (D) in.)
Weight (without package). . . . . . . . . . . 31.0 kg (68.4 lb 6 oz)
Furnished Parts
Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control unit recharger. . . . . . . . . . . . . . . . . . . . . . . 1
AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
U-shaped connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
These operating instructions . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Note
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
• This product includes FontAvenue® fonts licensed by
NEC corporation. FontAvenue is a registered trademark
of NEC corporation.
Component Video Section
Input (Sensitivity/Impedance) . . . . . . . . . . . . . . 1 Vp-p/75 Ω
Output (Level/Impedance) . . . . . . . . . . . . . . . . . 1 Vp-p/75 Ω
111
En
Published by Pioneer Corporation.
Copyright © 2003 Pioneer Corporation.
All rights reserved.
<03J00001>
Printed in Japan
<ARB7290-A>
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement