Planet Technology POE-400 User's Manual

Planet Technology POE-400 User's Manual
IEEE 802.3af
4-Port Power over Ethernet Injector Hub
POE-400
User’s Manual
-1-
Trademarks
Copyright  PLANET Technology Corp. 2006.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on
the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET IEEE 802.3af Power over Ethernet Injector Hub User’s manual
FOR MODEL: POE-400
REVISION: 1.0 (DECEMBER.2006)
Part No.: EM_POE400v1 (2080-A31120-001)
-2-
TABLE OF CONTENTS
1. INTRODUCTION.......................................................................................................................................... 4
1.1 CHECKLIST ................................................................................................................................................ 4
1.2 ABOUT THE POWER OVER ETHERNET INJECTOR HUB................................................................................... 4
1.3 FEATURES ................................................................................................................................................. 4
1.4 SPECIFICATION .......................................................................................................................................... 5
1.5 PRODUCT OUTLOOK ................................................................................................................................... 5
2. HARDWARE INSTALLATION...................................................................................................................... 6
2.1. Before Installation................................................................................................................................ 6
2.2 POE-400 and POE-152S, the IEEE 802.3af Injector / Splitter and equipment installation ................. 7
3. TROUBLESHOOTING .................................................................................................................................. 8
APPENDIX A NETWORKING CONNECTION.................................................................................................. 9
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS ........................................................................................................... 9
A.2 RJ-45 CABLE PIN ASSIGNMENT ................................................................................................................... 9
-3-
1. INTRODUCTION
1.1 Checklist
Thank you for purchasing our POE-400 IEEE 802.3af Power over Ethernet Injector Hub, your Power over Ethernet Injector
Hub package shall contains following contents:
Check the contents of your package for following parts:
Power over Ethernet Injector Hub x1
User's manual CD x1
Power Adapter x1
Power cord x 1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it to
us for repair.
1.2 About the Power over Ethernet Injector Hub
The PLANET POE-400 is a 4-Port IEEE 802.3af Power over Ethernet injector hub complied with IEEE 802.3, IEEE 802.3u
and IEEE 802.3af standards. Equipped with 4 10/100Base-TX Fast Ethernet ports, the POE-400 supports full 48VDC
power for any remote IEEE 802.3af powered device (PD) like Wireless LAN Access Point, IP phone, and LAN Camera.
Supporting power supply of 70 watts, POE-400 provides sufficient power to the 4 remote devices.
There are 8 RJ-45 STP ports on POE-400. Half of the ports on right panel function as "Data" and the other half on left
panel function as "Data and Power". Each of the "Data and Power" port as an injector which inserts DC Voltage into
the CAT 5 cable allowing the cable between the Injector and Splitter to transfer data and power simultaneously.
1.3 Features
◆ Complies with IEEE 802.3, IEEE 802.3u, 10/100Base-TX
◆ Complies with IEEE 802.3af, 48VDC power over unused twisted-pair wires
◆ 4-Port IEEE 802.3af in-line mid-span power injector box
◆ Full power support for per POE port
◆ Circuit protection prevent power interference between ports
◆ LED indicator power input indication
◆ Desktop palm size
-4-
1.4 Specification
Model
Ethernet Connector
POE-400
8-Port RJ-45 STP with 4-Port "Data" and 4-Port "Data and Power"
Ethernet Data rate
10/100Mbps( vary on Ethernet device attached)
Input voltage
DC 48V, 1.5A
Number of device can be powered
4
Ethernet cable
TIA/EIA-568, Category 5/5e cable
LED indicator
1 x power, 4 x POE ready / in-use
Operating environment
0~50 Degree C, 5%~90%RH
Storage environment
-20~70 Degree C, 5%~90%RH
Dimension (H x W x D)
26 x 70 x 97mm
Weight
220g
Emission
FCC Class B, CE mark
Standard Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3af Power over Ethernet
1.5 Product Outlook
LED definition:
LED
Color
Function
Power
Green
Lights to indicate that the POE-400 has power.
PoE ready / in-use
Green
Lights to indicate the port is providing 48VDC in-line power.
-5-
2. HARDWARE INSTALLATION
This product provides two different running speeds – 10Mbps, 100Mbps, in the same device and automatically distinguishes the speed of incoming connection.
This section describes the hardware features of POE-400. Before connecting any network device to the POE-400, read
this chapter carefully.
2.1. Before Installation
Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices need
to power on, the POE-400 can provide you a way to supply power for this Ethernet device conveniently and easily. The
POE-400 equips with an AC-DC adapter with DC 48V input and injects this DC power into the pin of the twisted pair cable
(pair 4, 5 and pair 7, 8).
If there is very difficult to find a power socket for AC-DC Adapter of your non-IEEE 802.3af networked device, the POE-400
and POE-152S can provide you a way to supply DC power for this Ethernet device conveniently and easily.
The 10Mbps or 100Mbps speed, duplex mode from Data port of POE-400 depends on which Ethernet device attached.
-6-
2.2 POE-400 and POE-152S, the IEEE 802.3af Injector / Splitter and equipment installation
For the places hard to find the power inlet, the POE-400 provide the easiest way to power your Ethernet devices such as
PLANET IEEE 802.3af Power over Ethernet Splitter( POE-152S) with Internet Camera (ICA-210 ) or Wireless Access
Point (WAP-4060PE) installed in the small office.
To control the power system of your networking devices, the POE-400 can directly co-work with PLANET ICA-100PE and
POE IP Phone VIP-153PT to build VoIP telephony network in the office. Besides, the POE-400 can be directly deployed to
connect the third party IEEE 802.3af devices like Cisco AP and POE switches installed 100 meters away.
Figure 1: Connection architecture over POE-400
Notice:
1. According to IEEE 802.3af standard, the POE-400 will not inject power to the cable if not connecting to IEEE 802.3af
devices.
2. Due to the capability of IEEE 802.3af standard, the POE-400 can directly connect with any IEEE 802.3af end-nodes.
-7-
3. TROUBLESHOOTING
This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the
Ethernet Switch was set up according to instructions in this manual.
How to let my non IEEE 802.3af network devices can work with POE-400?
Solution:
You can use PLANET Power over Ethernet Splitter, such as PLANET POE-152S to work as a power
transformer between POE-400 and non IEEE 802.3af devices. Two types of POE-152S are available
for different voltage, 5V DC and 12V DC.
The PoE LED is not lit
Solution:
Check the cable connection between POE-400 and IEEE 802.3af device.
Why I connect my PoE device to POE-400 and it cannot power on?
Solution:
1. Please check the cable type of the connection from POE-400 to the other end. The cable should
be an 8-wire UTP, Category 5/5e, EIA568 cable within 100 meters. A cable with only 4-wire, short
loop or over 100 meters, all will affect the power supply.
2.
Please check and assure the device that fully complied with IEEE 802.3af standard.
-8-
APPENDIX A NETWORKING CONNECTION
A.1 Switch‘s RJ-45 Pin Assignments
10/100Mbps, 10/100Base-TX
RJ-45 Connector pin assignment
MDI
MDI-X
Contact
Media Dependant
Interface
Media Dependant
Interface -Cross
1
Tx + (transmit)
Rx + (receive)
2
Tx - (transmit)
Rx - (receive)
3
Rx + (receive)
Tx + (transmit)
4, 5
6
7, 8
IEEE 802.3af DC 48V
Rx - (receive)
Tx - (transmit)
IEEE 802.3af DC 0V
A.2 RJ-45 cable pin assignment
The standard RJ-45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation
and color of straight cable and crossover cable connection:
Figure A-1: Straight-Through and Crossover Cable
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the
cables into your network.
2080-A31120-001
-9-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement