Brocade Communications Systems POWEREDGE 840 Reference Manual

53-1001156-01

24 November 2008

Fabric OS

MIB Reference

Supporting Fabric OS v3.1.x, v3.2.x, v4.1.x, v4.2.x, v4.4.x, v5.0.x, v5.1.x, v5.2.x, v5.3.x, v6.0.0, v6.1.0, v6.2.0

Copyright © 2007-2008 Brocade Communications Systems, Inc. All Rights Reserved.

Brocade, Fabric OS, File Lifecycle Manager, MyView, and StorageX are registered trademarks and the Brocade B-wing symbol,

DCX, and SAN Health are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries.

All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability.

Export of technical data contained in this document may require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other open source license agreements. To find-out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit

http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Corporate Headquarters

Brocade Communications Systems, Inc.

1745 Technology Drive

San Jose, CA 95110

Tel: 1-408-333-8000

Fax: 1-408-333-8101

Email: [email protected]

Asia-Pacific Headquarters

Brocade Communications Singapore Pte. Ltd.

30 Cecil Street

#19-01 Prudential Tower

Singapore 049712

Singapore

Tel: +65-6538-4700

Fax: +65-6538-0302


European and Latin American Headquarters

Brocade Communications Switzerland Sàrl

Centre Swissair

Tour A - 2ème étage

29, Route de l'Aéroport

Case Postale 105

CH-1215 Genève 15

Switzerland

Tel: +41 22 799 56 40

Fax: +41 22 799 56 41


Document History

Document Title

Brocade MIB Reference Manual v2.3

Brocade MIB Reference Manual v3.0

Brocade MIB Reference Manual v3.0, 4.0

Brocade MIB Reference Manual

(v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)

Publication Number

53-0000069-02

53-0000134-03

53-0000184-02

53-0000521-02


(v4.1.2, v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)


(v4.1.2, v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)


(v4.2.0, v4.1.2, v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)

Brocade Fabric OS MIB Reference Manual

53-0000521-03

53-0000521-04

53-0000521-06

Brocade Fabric OS MIB Reference Manual

53-0000521-08

53-0000521-09

Brocade Fabric OS MIB Reference Manual 53-1000045-01

Brocade Fabric OS MIB Reference





53-1000241-01

53-1000439-01

53-1000602-01

53-1000602-02

53-1001156-01

Summary of Changes Publication Date

December 2000

July 2001

Added Brocade-specific

Entity and

HA-MIBs.

March 2002

April 2003

Added FICON information. May 2003

Revised FICON information.

October 2003

Update to support the

Brocade 3250, 3850, and

24000 switches.

December 2003

September 2004 Updated to support the

Brocade 4100.

Updated to support the

Brocade 48000 and

200E.

April 2005



FR4-18i blade.

January 2006

Changed name, updated to support Fabric OS 5.2.x

September 2006

New branding, updated to support Fabric OS 5.3.0

June 2007


Brocade DCX Data Center

Backbone Director

October 2007



5300 switches.

March 2008


Brocade DCX-4S and

Brocade Encrytion Switch.

November 2008

Contents

Fabric OS MIB Reference

53-1001156-01

About This Document

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . xii

What’s new in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Document conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

Getting technical help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi

Chapter 1 Understanding Brocade SNMP

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Setting the SNMP Security Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Understanding SNMP Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Understanding MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Understanding SNMP Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Object Instances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Loading Brocade MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Brocade MIB Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before Loading MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

MIB Loading Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SNMP CLI usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Brocade 7500 / FR4-18i and Brocade MIBs . . . . . . . . . . . . . . . . . . 11

Access Gateway and Brocade MIBs. . . . . . . . . . . . . . . . . . . . . . . . . . 11

Firmware Upgrades and Enabled Traps. . . . . . . . . . . . . . . . . . . . . . . 11

Fabric OS Commands for Configuring SNMP . . . . . . . . . . . . . . . . . .12

Support for Administrative Domains . . . . . . . . . . . . . . . . . . . . . . . . .12

Support for Role Based Access Control. . . . . . . . . . . . . . . . . . . . . . .12

Support for IP V6 Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Support for Virtual Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

v

vi

Chapter 2

Chapter 3

Chapter 4

MIB-II (RFC1213-MIB)

MIB II Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

System Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Interfaces Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

AT Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

IP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

ICMP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110

TCP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137

UDP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160

EGP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168

Transmission Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168

SNMP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168

ifMIB Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196

FE MIB Objects

FE MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .219

FIBRE-CHANNEL-FE-MIB (MIB-II branch) . . . . . . . . . . . . . . . . . . . . .219

Definitions for FIBRE-CHANNEL-FE-MIB. . . . . . . . . . . . . . . . . . . . . .224

fcFeConfig Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226

fcFeStatus Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254

fcFeError Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .282

feFcAccounting Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .296

fcFeCapability Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324

FCFABRIC-ELEMENT-MIB (Experimental Branch) . . . . . . . . . . . . . .340

fcFeConfig Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .347

fcFeOp Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .382

fcFeError Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

fcFeAcct Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433

fcFeCap Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433

Entity MIB Objects

Entity MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .453

Entity MIB System Organization of MIB Objects . . . . . . . . . . .454

Definitions for Entity MIB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .455

Textual Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .457

Entity MIB Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .459

Physical Entity Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460


53-1001156-01


53-1001156-01

Chapter 5

Chapter 6

Chapter 7

Logical Entity Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .480

Entity Mapping Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .490

General Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500

Entity MIB Trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .501

Entity MIB Conformance Information. . . . . . . . . . . . . . . . . . . . . . . .502

SW-MIB Objects

SW MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .511

SW-MIB System Organization of MIB Objects . . . . . . . . . . . . .511

Textual Conventions for SW-MIB . . . . . . . . . . . . . . . . . . . . . . . .519

sw Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .522

swSystem Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .532

Flash Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .541

swFabric Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .568

SW Agent Configuration Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . .593

Fibre Channel Port Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .598

Name Server Database Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . .639

Event Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .656

Fabric Watch Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .666

End Device Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711

Switch Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .721

ASIC Performance Monitoring Group . . . . . . . . . . . . . . . . . . . . . . . .732

Trunking Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .753

High-Availability MIB Objects

HA MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .775

High-Availability Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .777

FRU Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .779

FRU History Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .788

CP Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .797

HA-MIB Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .803

HA-MIB Traps and Sample Triggers. . . . . . . . . . . . . . . . . . . . . .806

FICON MIB Objects

FICON MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .807

SNMP Traps for FICON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .807

FICON MIB System Organization of MIB Objects . . . . . . . . . . .807

Textual Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .809

vii

viii

Chapter 8

Chapter 9

Chapter 10

Appendix A

ficonRNID Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .811

ficonLIRR Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .841

ficonRLIR Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .851

linkIncidentMIBTraps Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .867

FibreAlliance MIB Objects

FibreAlliance MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .873

FCMGMT-MIB System Organization of MIB Objects . . . . . . . . 874

Definitions for FCMGMT-MIB. . . . . . . . . . . . . . . . . . . . . . . . . . .879

ConnSet Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .881

Statistics Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .982

Service Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1034

SNMP Trap Registration Group. . . . . . . . . . . . . . . . . . . . . . . . . . . 1053

Revision Number Scalar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1061

Unsupported Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1061

FibreAlliance MIB Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1062

FCIP MIB Objects

FCIP MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067

FCIP MIB System Organization of MIB Objects . . . . . . . . . . 1068

fcipEntityInstanceTable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1070

fcipLinkTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1079

FCIP Extended Link Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1092

iSCSI MIB Objects

iSCSI MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1107

iSCSI MIB System Organization of MIB Objects . . . . . . . . . . 1108

iscsiInstanceAttributesTable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1111

iscsiNodeAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125

iscsiSessionAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145

iscsiSessionStatsTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1168

iscsiConnectionAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . .1176

MIB Object Groupings

Switch Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195

Sensor Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195

Port Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195

Event Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196


53-1001156-01

Appendix B

Index

ISL and End Device Variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196

SNMP Configuration Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196

iSCSI Instance Information Variables . . . . . . . . . . . . . . . . . . . . . .1197

MIB OIDs and Their Matching Object Names

MIB OIDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199


53-1001156-01 ix

x Fabric OS MIB Reference

53-1001156-01

About This Document

In this chapter

•

How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

•

Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

•

What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

•

Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

•

Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

•

Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

•

Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi

How this document is organized

This document is organized to help you find the information that you want as quickly and easily as possible.

The document contains the following components:

•

Chapter 1, “Understanding Brocade SNMP”

provides an introduction to Brocade SNMP and

MIBs.

•

Chapter 2, “MIB-II (RFC1213-MIB)”

provides information for MIB-II.

•

Chapter 3, “FE MIB Objects”

provides information for FE MIB object types.

•

Chapter 4, “Entity MIB Objects” provides information for Entity MIB object types.

•

Chapter 5, “SW-MIB Objects”

provides information for FC Switch MIB (SW-MIB) object types.

•

Chapter 6, “High-Availability MIB Objects”

provides information for High-Availability MIB object types.

•

Chapter 7, “FICON MIB Objects” provides information for FICON MIB (LINK-INCIDENT-MIB)

object types.

•

Chapter 8, “FibreAlliance MIB Objects” provides information for FibreAlliance MIB

(FCMGMT-MIB) object types.

•

Chapter 9, “FCIP MIB Objects” provides information on FCIP MIB support for 7500 switches and

FC4-18i blades.

•

Chapter 10, “iSCSI MIB Objects” provides information on iSCSI MIB support for 7500 switches

and FC4-18i blades.

•

Appendix A, “MIB Object Groupings”

is a function-based listing of MIB objects.

•

Appendix B, “MIB OIDs and Their Matching Object Names” provides a listing of the MIB object

names and the corresponding MIB Object ID (OID) associated with each.


53-1001156-01 xi

Supported hardware and software

In those instances in which procedures or parts of procedures documented here apply to some switches but not to others, this guide identifies exactly which switches are supported and which are not.

Although many different software and hardware configurations are tested and supported by

Brocade Communications Systems, Inc. for 6.2.0, documenting all possible configurations and scenarios is beyond the scope of this document.

This document supports Brocade Fabric OS versions v6.2.0 and earlier versions, v6.1.0, v6.0.0, v5.3.x, v 5.2.x, v5.1.x, v5.0.x, v4.4.0, v4.2.x, v4.1.x, v3.2.x, v3.1.x and all switches supporting these

Fabric OS versions, including:

•

Brocade 200E Switch

•

Brocade 300 switch

•

Brocade 3014 Switch

•

Brocade 3016 Switch

•

Brocade 3200 Switch

•

Brocade 3250 Switch

•

Brocade 3800 Switch

•

Brocade 3850 Switch

•

Brocade 3900 Switch

•

Brocade 4012 Switch

•

Brocade 4100 Switch

•

Brocade 4020 Switch

•

Brocade 4900 Switch

•

Brocade 5000 Switch

•

Brocade 5100 switch

•

Brocade 5300 switch

•

Brocade 7500 Switch

•

Brocade 7600 Switch

•

Brocade 12000 Director

•


•


•

Brocade DCX

•

Brocade DCX-4S

•

FA4-16 Blade

•

FC10-6 Blade

•

FC4-16IP Blade

•

FC4-48C Blade

•

FR4-18i Blade

•

FC8-16 Blade

xii Fabric OS MIB Reference

53-1001156-01

•

FC8-32 Blade

•

FC8-48 Blade

What’s new in this document

The following changes have been made since this document was last released:

•

Information that was added:

-

Support for Brocade DCX-4S and Brocade Encrytion Switch

swTopTalker MIB

-

Support for Virtual Fabric

-

New attributes added to the following:

• fcipExtendedLinkTable

• swFCport Hierarchy

• swfabric Hierarchy

• swSystem Hierarchy

• swTrapsV2

•

Information that was changed:

-

Miscellaneous additions and corrections have been made throughout

For further information about new features and documentation updates for this release, refer to the release notes.

Document conventions

This section describes text formatting conventions and important notices formats.

Text formatting

The narrative-text formatting conventions that are used in this document are as follows: bold text Identifies command names

Identifies the names of user-manipulated GUI elements

Identifies keywords and operands

Identifies text to enter at the GUI or CLI

italic text code

text

Provides emphasis

Identifies variables

Identifies paths and Internet addresses

Identifies document titles

Identifies CLI output

Identifies syntax examples


53-1001156-01 xiii

For readability, command names in the narrative portions of this guide are presented in mixed lettercase: for example, switchShow. In actual examples, command lettercase is often all lowercase. Otherwise, this manual specifically notes those cases in which a command is case sensitive.

Notes, cautions, and warnings

The following notices and statements are used in this manual. They are listed below in order of increasing severity of potential hazards.

NOTE

A note provides a tip, guidance or advice, emphasizes important information, or provides a reference to related information.

ATTENTION

An Attention statement indicates potential damage to hardware or data.

CAUTION

A Caution statement alerts you to situations that can be potentially hazardous to you or cause damage to hardware, firmware, software, or data.

DANGER

A Danger statement indicates conditions or situations that can be potentially lethal or extremely hazardous to you. Safety labels are also attached directly to products to warn of these conditions or situations.

Key terms

For definitions specific to Brocade and Fibre Channel, see the technical glossaries on Brocade

Connect. See “Brocade resources” on page xv for instructions on accessing Brocade Connect.

For definitions of SAN-specific terms, visit the Storage Networking Industry Association online dictionary at:

http://www.snia.org/education/dictionary

Notice to the reader

This document may contain references to the trademarks of the following corporations. These trademarks are the properties of their respective companies and corporations.

These references are made for informational purposes only.

xiv Fabric OS MIB Reference

53-1001156-01

Corporation

Microsoft Corporation

Sun Microsystems, Inc.

Referenced Trademarks and Products

Windows, Windows NT, Internet Explorer

Sun, Solaris

Additional information

This section lists additional Brocade and industry-specific documentation that you might find helpful.

Brocade resources

To get up-to-the-minute information, join Brocade Connect. It’s free! Go to

http://www.brocadeconnect.com

to register at no cost for a user ID and password.

For practical discussions about SAN design, implementation, and maintenance, you can obtain

Building SANs with Brocade Fabric Switches through: http://www.amazon.com

For additional Brocade documentation, visit the Brocade SAN Info Center and click the Resource

Library location: http://www.brocade.com

Other industry resources

For information about the Fibre Channel industry, visit the Fibre Channel Industry Association Web site: http://www.fibrechannel.org

Getting technical help

Contact your switch supplier for hardware, firmware, and software support, including product repairs and part ordering. To expedite your call, have the following information immediately available:

1. General Information

•

Technical Support contract number, if applicable

•

Switch model

•

Switch operating system version

•

Error numbers and messages received

• supportSave command output

•

Detailed description of the problem, including the switch or fabric behavior immediately following the problem, and specific questions


53-1001156-01 xv

•

Description of any troubleshooting steps already performed and the results

•

Serial console and Telnet session logs

•

Syslog message logs

2. Switch Serial Number

The switch serial number and corresponding bar code are provided on the serial number label, as shown here:

*FT00X0054E9*

FT00X0054E9

The serial number label is located as follows:

•

Brocade 200E—On the nonport side of the chassis

•

Brocade 300, 4100, 4900, 5100, 5300, and 7500—On the switch ID pull-out tab located inside the chassis on the port side on the left

•

Brocade 5000—On the switch ID pull-out tab located on the bottom of the port side of the switch

•

Brocade 7600—On the bottom of the chassis

•

Brocade 48000, Brocade DCX, Brocade DCX-4S—Inside the chassis next to the power supply bays.

3. World Wide Name (WWN)

•

Use the wwn command to display the switch WWN. If you cannot use the wwn command because the switch is inoperable, you can get the WWN from the same place as the serial number.

Document feedback

Because quality is our first concern at Brocade, we have made every effort to ensure the accuracy and completeness of this document. However, if you find an error or an omission, or you think that a topic needs further development, we want to hear from you. Forward your feedback to:

[email protected]

Provide the title and version number and as much detail as possible about your comment, including the topic heading and page number and your suggestions for improvement.

xvi Fabric OS MIB Reference

53-1001156-01

Understanding Brocade SNMP

Chapter

1

In this chapter

•

Setting the SNMP Security Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

•

Understanding SNMP Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•

Loading Brocade MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

•

Brocade 7500 / FR4-18i and Brocade MIBs. . . . . . . . . . . . . . . . . . . . . . . . . 11

•

Firmware Upgrades and Enabled Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

•

Fabric OS Commands for Configuring SNMP. . . . . . . . . . . . . . . . . . . . . . . . . 12

Setting the SNMP Security Level

The Simple Network Management Protocol (SNMP) is an industry-standard method of monitoring and managing network devices. This protocol promotes interoperability because SNMP-capable systems must adhere to a common set of framework and language rules.

Understanding the components of SNMP makes it possible to use third-party tools to view, browse, and manipulate Brocade switch variables (MIBs) remotely as well as to set up an enterprise-level management process. Every Brocade switch and director supports SNMP.

Recipients for SNMP traps are restricted according to security levels. Security levels are selected and set for a switch using the snmpconfig --set seclevel command. To select and set SNMP security levels, issue the command snmpconfig --set seclevel after having logged in to the switch as admin.

The following example sets the SNMP security level to 1 (authentication only). This setting allows all

SNMPv1 users to perform GET and SET operations on MIBs, but creates an exception for SNMPv3 users that do not have authentication and privacy privileges (noAuthnoPriv).

switch:admin> snmpconfig --set seclevel

Select SNMP Security Level

(0 = No security, 1 = Authentication only, 2 = Authentication and Privacy, 3 = sxNo Access): (0..3) [0]

Select SNMP SET Security Level

(0 = No security, 1 = Authentication only, 2 = Authentication and Privacy, 3 =

No Access): (0..3) [0]

TABLE 1

security level

Security Level Options

Protocol

No security [0]

(noAuthnoPriv)

Authentication only [1]

(authNoPriv)

SNMPv1

SNMPv3

SNMPv1

SNMPv3

Query Behavior

Allowed.

Allowed.

Allowed.

All SNMPv3 users allowed except noAuthNoPriv users.

Traps

Sent.

Sent.

Sent.

Sent for all SNMPv3 users except noAuthNoPriv users.


53-1001156-01

1

2

1

Understanding SNMP Basics

TABLE 1

security level

Security Level Options (Continued)

Protocol Query Behavior

Authentication and

Privacy [2]

(authPriv)

No Access [3]

SNMPv1

SNMPv3

SNMPv1

SNMPv3

Not allowed.

Only SNMPv3 users with authPriv privilege are allowed.

Not allowed.

Traps

Not Sent.

Sent only for authPriv users.

Not Sent.


Every Brocade switch carries an agent and management information base (MIB), as shown in

Figure 1 . The agent accesses information about a device and makes it available to an SNMP

network management station.

SNMP

Management Station

Agent

MIB

FIGURE 1

SNMP Structure

When active, the management station can get information or set information when it queries an agent. SNMP commands, such as get, set, getnext, setnext, and getresponse, are sent from the

management station, and the agent replies once the value is obtained or modified ( Figure 2 ).

Agents use variables to report such data as the number of bytes and packets in and out of the device, or the number of broadcast messages sent and received. These variables are also known as managed objects. All managed objects are contained in the MIB.

get, getnext, set

Management Station Agent reply

FIGURE 2

SNMP Query

The management station can also receive traps, unsolicited messages from the switch agent if an unusual event occurs. Refer to

“Understanding SNMP Traps” on page 4 for more information.

Management Station

TRAP

Agent

FIGURE 3

SNMP Trap

The agent can receive queries from one or more management stations and can send traps to up to

six management stations.


53-1001156-01


53-1001156-01


1

Understanding MIBs

The management information base (MIB) is a database of monitored and managed information on a device, in this case a Brocade switch. The MIB structure can be represented by a tree hierarchy.

The root splits into three main branches: International Organization for Standardization (ISO),

Consultative Committee for International Telegraph and Telephone (CCITT), and joint ISO/CCITT.

These branches have short text strings and integers (OIDs) to identify them. Text strings describe

object names, while integers allow software to create compact, encoded representations of the names.

Each MIB variable is assigned an object identifier (OID). The OID is the sequence of numeric labels on the nodes along a path from the root to the object. For example, as shown in

Figure 4 , the

Brocade SW.MIB OID is:

1.3.6.1.4.1.1588

The corresponding name is: iso.org.dod.internet.private.enterprise.bsci

The other branches are part of the standard MIBs, and the portions relevant to configuring SNMP on a Brocade switch are referenced in the remainder of this reference.

iso (1) org (3)

Brocade SW MIB

1.3.6.1.4.1.1588

dod (6) internet (1) directory (1) mgmt (2) experimental (3) private (4) mib-2 (1) fibreChannel (42) enterprise (1) system (1) interface (2) fcFe (1) bcsi (1588) sysDescr (1) sysObjectID (2) fcFabric (2)

FIGURE 4

Brocade MIB Tree Location

Use a MIB browser to access the MIB variables: all MIB browsers perform queries and load MIBs.

Since different vendors vary the information in their private enterprise MIBs, it is necessary to verify their information. The Fibre Channel MIB standards dictate that certain information be included in all MIBs: it is the vendors’ responsibility to follow the standards. The standards are:

•

FibreAlliance (FA) MIB: Brocade supports version 3.0.

•

Fabric Element (FE) MIB: accepted by the Internet Engineering Task Force (IETF).

3

4

1


Brocade supports FE_RCF2837.mib under the MIB-II branch in Fabric OS v6.2.0, v6.1.0, v6.0.0, v4.x, v3.2.0, and v3.1.x and the experimental version, FE_EXP.mib, in Fabric OS v2.6.x and 3.0.x. This latest version of the FE MIB references the FRAMEWORK.MIB and, based on

the MIB browser, it is necessary to load this MIB before the FE.MIB. Refer to “Loading Brocade

MIBs” on page 6 for more information.

Once loaded, the MAX-ACCESS provides access levels between the agent and management station.

The access levels are as follows:

• not-accessible

You cannot read or write to this variable.

• read-create

Specifies a tabular object that can be read, modified, or created as a new row in a table.

• read-only - Public

You can only monitor information.

• read-write - Private

You can read or modify this variable.

Understanding SNMP Traps

An unsolicited message that comes to the management station from the SNMP agent on the device is called a trap. Brocade switches send traps out on UDP port 162 and to any configured port. In order to receive traps, the management station IP address and severity level must be configured on the switch. Up to six trap recipients can be configured using Web Tools or the snmpConfig command. You can define a different message severity level for each recipient so that some recipients receive all trap messages and others receive only the most critical.

There are two main MIB trap choices:

•

FibreAlliance MIB trap - Associated with the Fibre Alliance MIB (FA-MIB), this MIB manages SAN switches and devices from any company that complies with Fibre Alliance specifications.

•

Brocade-specific MIB trap - Associated with the Brocade-specific Brocade MIB (SW-MIB), manages Brocade switches only.

There is some overlap in the functionality of these MIBs. If you enable both SW-MIB and FA-MIB traps, you could receive duplicate messages for the switch events that trigger the trap.

You can also use these additional MIBs and their associated traps: HA-MIB; FICON-MIB; and

SW-EXTTRA. You can use the snmpConfig command to disable the FA-MIB, HA-MIB, FICON-MIB, and

SW_EXTTRA; but neither the SW-MIB or the FE-MIB can be disabled.

An event trap (swEventTrap, connUnitEventTrap, or swFabricWatchTrap) is basically an error message (errShow output) that is SNMP-formatted and delivered.

FA Traps

Consider enabling the FA traps if you want to use SNMP to monitor multiple connectivity units, including Brocade switches.

The switchStatusPolicySet command determines the FA-TRAP switch status-related outputs:

• connUnitStatusChange

• connUnitSensorStatusChange


53-1001156-01


53-1001156-01


1

• connUnitPortStatusChange

• connUnitEventTrap

The MIB-II system description swEventTrapLevel determines the output for the connUnitEventTrap.

Events in the Error Log of a severity at or above the configured threshold will generate SNMP traps.

The Fibre Alliance Trap (FA-TRAP) can be configured to send traps using the snmpConfig command.

Refer to the Fabric OS Command Reference for more information on this command.

HA Traps

Consider enabling these traps to monitor field-replaceable unit (FRU) status and control processor

(CP) status when you have a Brocade director in your environment:

• fruStatusChanged

This trap is generated by a FRU status change, such as a switch reboot or disabling or enabling a FRU component such as (fandisable/fanenable, etc).

• cpStatusChanged

This trap is generated by a change in the status of a CP, including a reboot or firmware download.

• fruHistoryTrap

This trap is generated when a FRU is added or removed. fruHistoryTrap is not generated when standby CP is removed.

The high availability trap (HA-TRAP) can be configured to send traps using the snmpConfig command. Refer to the Fabric OS Command Reference for more information on this command.

SW Traps

There are six specific traps defined in Brocade SW-TRAP.

1. swfault (no longer supported)

2. swSensorScn (no longer supported)

3. swFCPortScn

This trap is generated by a port state change.

4. swEventTrap

This trap is generated by any switch event reported to the system error log.

5. swFabricWatchTrap

This trap is generated when any Fabric Watch threshold is reached.

6. swTrackChangesTrap

This trap is generated by a login or a logout.

The Brocade trap (SW-TRAP) can be configured to send traps using the snmpConfig command.

Refer to the Fabric OS Command Reference for more information on this command.

5

6

1

Loading Brocade MIBs

Object Instances

MIB objects are defined by the OID, which is the type of object, and by the instance number, which is an instance of that MIB object. A Fibre Channel port is a MIB object, and port 0 is an instance of that object. The following is an OID number and an instance number:

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11.5

where:

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11

is the OID (of swFCPortTxWords) and 5 is the instance

ID for port 4.

You must add 1 to the port number to get its instance number in SNMP because SNMP numbering starts at 1; switch port numbering starts at 0.


The Brocade MIB is a set of variables that are private extensions to the Internet standard MIB-II.

The Brocade agents support many other Internet-standard MIBs. These standard MIBs are defined in RFC publications. To find specific MIB information, examine the Brocade proprietary MIB structure and the standard RFC MIBs supported by Brocade.

Brocade MIB Files

The Brocade MIB files are as follows:

•

BRCD_v5_0.mib

• brcdfcip.mib

•

CPQ_HOST.mib

•

CPQ_RACK.mib

•

ENTITY_RFC2737.mib

•

FA_v3_0.mib

• fcip.mib

•

FE_RFC2837.mib

•

FICON_v5_0.mib

•

HA_v5_1.mib

•

IF.mib

•

IF_TYPE.mib

•

INET_ADDR.mib

•

ISCSI_RFC4544.mib

•

SW_v5_7.mib

Before Loading MIBs

Before loading Brocade MIB files, ensure that you have the correct version of SNMP for your Fabric

OS version (

Table 2 ).


53-1001156-01


53-1001156-01


1

TABLE 2

Firmware

Fabric OS Supported SNMP Versions

SNMPv1

Fabric OS v2.6.2 and previous



Fabric OS v4.4.0

Fabric OS v5.x

Fabric OS v6.0.0

Fabric OS v6.1.0

Fabric OS v6.2.0

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

SNMPv2

No

1

No

1

No

1

No

1

Yes

3

Yes

Yes

Yes

SNMPv3

Yes

Yes

Yes

No

No

No

Yes

2

Yes

2

1.

The corresponding Fabric OS has SNMPv2 capabilities, but it is not officially supported by Brocade.

2.

Fabric OS v4.4.0 and v5.x support SNMPv3-USM MIB (snmpUsmMIB), which is available as

RFC 3414.

3.

SNMPv2 is supported from Fabric OS v5.0.4 and higher, but SNMP v2 traps are not supported.

MIB Loading Order

Many MIBs use definitions that are defined in other MIBs. These definitions are listed in the

IMPORTS section near the top of the MIB. When loading the Brocade MIBs, refer to Figure 5

to ensure any MIB dependencies are loading in the correct order.

7

1


8

RFC1213-MIB

MIB-II

RFC1155-SMI

Select one

FA_v2_2.mib

FCMGMT-MIB

FOS 2.6.x

FA_v3_0.mib

FCMGMT-MIB

FOS 3.x, 4.x, 5.x

Select one or both

FE_EXP.mib

FCFABRIC-ELEMENT-MIB

FE_RFC2837.mib

FIBRE-CHANNEL-FE-MIB

FOS 3.1.x, 4.x, 5.x

FICON_v5_0.mib

FICON-MIB

FOS 4.x, 5.x

SNMPv2-SMI

SMNPv2-TC

BRCD_v5_0.mib

Brocade-REG-MIB

Brocade-TC

FOS 2.6.x, 3.x, 4.x, 5.x

INET-ADDRESS-MIB snmpUsmMIB

User-based Security Model

SW_v5_5.mib

FOS 2.6.x, 3.x, 4.x, 5.x

ENTITY_RFC2737.mib

ENTITY-MIB

FOS 4.x, 5.x

HA_v5_1.mib

HA-MIB

FOS 4.x, v5.x

SNMPv2-CONF

RFC2571

SNMP-FRAMEWORK-MIB fcip.mib

brcdfcip.mib

Legend

ISCSI_RFC4544.mib

Standard MIB File

Module name

Dependency

Brocade MIB

Module name

FOS supported

NOTE

FA_v3_0.mib obsoletes the use of the connUnitPortStatFabricTable used in the FA_v2_2.mib.

FA_v3_0.mib now uses the connUnitPortStatTable for port statistics. The FA_v3_0.mib and the

FA_v2_2.mib cannot be loaded concurrently on the same SNMP management system.

The FE_RFC2837.mib and the FE_EXP.mib can be loaded concurrently on the same SNMP management system. The FE_EXP.mib was listed in the experimental OID section. The

FE_RFC2837.mib has subsequently been ratified by the standards organizations.|

All versions of Fabric OS support SNMPv1. Fabric v2.6.x and v3.2.x partially support SNMPv2. Fabric

OS v4.4.0 and v5.0.1 support SNMPv3-USM (snmpUsmMIB) MIB. Fabric OS version 5.3.0 supports the FCIP MIB and ifXtable.

FIGURE 5

Brocade SNMP MIB Dependencies and Advised Installation Order

SNMP CLI usage

An example of the SNMPv3 User/Traps configuration is provided below.


53-1001156-01


53-1001156-01


1

Configuring SNMPv3 User/Traps

1. Create user on switch using CLI userconfig, with the required role.

switch:admin> userconfig --add fa_adm -r fabricadmin -h0 -a 0-255

Setting initial password for fa_adm

Enter new password:********

Re-type new password:********

Account fa_adm has been successfully added.

switch:admin>

Create user on switch in VF Context using CLI userconfig, with the required role.

switch:admin> userconfig --add sa_user -r switchadmin -l 1-128 -h1 -c admin

Setting initial password for sa_user

Enter new password:********

Re-type new password:********

Account sa_user has been successfully added.

switch:admin>

2. Create the SNMPv3 user as shown below.

switch:admin> snmpconfig --set snmpv3

SNMPv3 user configuration(snmp user not configured in FOS user database will have physical AD and admin role as the default):

User (rw): [snmpadmin1] fa_adm

Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] 1

New Auth Passwd:********

Verify Auth Passwd:********

Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]):

(1..6) [2] 1

New Priv Passwd:********

Verify Priv Passwd:********

User (rw): [snmpadmin2]

Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3]


(2..2) [2]

User (rw): [snmpadmin3]



(2..2) [2]

User (ro): [snmpuser1]



(2..2) [2]




(2..2) [2]




(2..2) [2]

SNMPv3 trap recipient configuration:

Trap Recipient's IP address : [0.0.0.0] 10.202.95.70

UserIndex: (1..6) [1]

Trap recipient Severity level : (0..5) [0] 5

Trap recipient Port : (0..65535) [162] 65000

Trap Recipient's IP address : [0.0.0.0]

9

10

1






Committing configuration...done.

switch:admin> switch:admin> snmpconfig --show snmpv3

SNMPv3 USM configuration:

User 1 (rw): fa_adm

Auth Protocol: MD5

Priv Protocol: DES

User 2 (rw): snmpadmin2

Auth Protocol: noAuth

Priv Protocol: noPriv

User 3 (rw): snmpadmin3



User 4 (ro): snmpuser1









SNMPv3 Trap configuration:

Trap Entry 1: 10.202.95.70

Trap Port: 65000

Trap User: fa_adm

Trap recipient Severity level: 5

Trap Entry 2: No trap recipient configured yet




Trap Entry 6: No trap recipient configured yet switch:admin>

3. Set the security level.

switch:admin> snmpconfig --set secLevel

Select SNMP GET Security Level


No Access): (0..3) [0] 2

Select SNMP SET Security Level


No Access): (2..3) [2] 2 switch:admin> snmpconfig --show secLevel

GET security level = 2, SET level = 2

SNMP GET Security Level: Authentication and Privacy

SNMP SET Security Level: Authentication and Privacy

4. In the Manager (SNMP Browser), create a user fa_adm with Authentication protocol as MD5,

Privacy protocol as DES, set the password and set the trap port as 65000. (Same values are set as in the switch SNMPv3 configuration.)


53-1001156-01

Brocade 7500 / FR4-18i and Brocade MIBs

1

Brocade 7500 / FR4-18i and Brocade MIBs

Beginning with release Fabric OS 5.3.0, statistics are available for FCIP tunnels, VEX_Ports, or

VE_Ports through the portstatsshow command.

The changes in the sensor details for FR4-18i Blade has been incorporated into SNMP. The

“connUnitSensorTable 1.3.6.1.3.94.1.8” on page 920 and

“swSensorTable

1.3.6.1.4.1.1588.2.1.1.1.1.22” on page 552 display information consistent with the Fabric OS

sensorShow command.

Access Gateway and Brocade MIBs

Brocade Access Gateway supports the following MIBs.

TABLE 3

Access Gateway MIB Support

MIB Name Supported Description

Updated to support Access Gateway in v5.2.1.

MIB-2

Entity-MIB

HA MIB

SW-MIB

Yes

Yes

Yes

No

FA-MIB

FE-MIB

CPQ-Rack MIB

FCIP MIB iSCSI MIB

Yes

No

Limited

Limited

Limited

Disabled in Access Gateway because the conventions are specific to fabric switches.

The connUnitSnsTable is not supported because a switch in Access

Gateway does support name server services.

Disabled in Access Gateway because the conventions are specific to fabric switches.

Supported on embedded switches only.

Implemented to support WAN interfaces in Fabric OS v5.3.0

Supports displaying information about virtual targets (VTs), iSCSI sessions, and TCP connection tables, as derived from specific MIB tables

Firmware Upgrades and Enabled Traps

Prior to Fabric OS v4.4, traps were turned on and off as a group (for example, the SW-Trap, or

FA-Trap). In these versions of the Fabric OS it was not possible to set individual traps (such as, swSensorStatusChangeTrap, swTrackChangesTrap, or connUnitEventTrap).

In Fabric OS v4.4 or above you can to turn on and off traps individually within a trap group. After the trap group is enabled, the individual traps need to be enabled explicitly.

Because the pre- Fabric OS v4.4 firmware only has trap group level settings, when you upgrade to the Fabric OS v4.4 firmware or above, individual traps are turned off by default even if the corresponding trap group was enabled before upgrading. When moving from a downlevel version to

Fabric OS v4.4 or above you must use the snmpconfig command to turn on explicitly the individual traps within each trap group.


53-1001156-01

11

1

Fabric OS Commands for Configuring SNMP

Fabric OS Commands for Configuring SNMP

Use the following commands to configure MIBs in the Fabric OS. Refer to the Fabric OS

Administrator’s Guide for procedures for configuring SNMP on the Brocade switches.

TABLE 4

Commands for Configuring SNMP

Command Description snmpConfig snmpMibCapSet snmpMibCapShow agtcfgDefault agtcfgSet agtcfgShow

SNMPMibCapSet

SNMPMibCapShow

This command has all the features of the existing the agtcfg* commands; in addition, it has SNMPv3 configuration parameters.

Enhanced in Fabric OS v4.4 to provide a filter facility at the trap level (previously the filter facility was at MIB level for traps).

Enhanced in Fabric OS 5.3.0 to support enabling and disabling of MIBs and traps for the FCIP MIB and the ifTable and ifXTable for FC ports (MIB II Intefaces group).

Enhanced in Fabric OS 6.2.0, where FCIP is enabled by default.

Displays the snmpMibCapSet command settings.

This command is deprecated. Only the snmpConfig command is working.





Support for Administrative Domains

Administrative Domains are supported in Fabric OS Version 5.3.0 and later releases. An

Administrative Domain (AD) is a domain within a fabric. Administrative domains can be used to limit administrator access within a fabric, and to provide service providers with a means to assign portions of a fabric to individual consumers. An AD may contain switches, devices, and ports. An AD may also limit access to a configured set of users.

Support for Role Based Access Control

Role Based Access Control (RBAC) is supported in Fabric OS Version 5.3.0 and later releases. RBAC applies a fixed set of roles that address the access control needs of a majority of customers. Each role is a set of permissions that can be applied to a user that controls the kinds of jobs and tasks the user can perform on a fabric or fabric element.

Support for IP V6 Addressing

IP V6 addressing is supported in Fabric OS Version 5.3.0 and later releases.

Support for Virtual Fabric

Virtual Fabric is supported in Fabric OS Version 6.2.0.

12 Fabric OS MIB Reference

53-1001156-01

MIB-II (RFC1213-MIB)

Chapter

2

This chapter provides descriptions and other information specific to MIB-II, and includes the following sections:

•

MIB II Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

•

System Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

•

Interfaces Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

•

AT Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

•

IP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

•

ICMP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

•

TCP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

•

UDP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

•

EGP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

•

Transmission Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

•

SNMP Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

•

ifMIB Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

MIB II Overview

The descriptions of each of the MIB variables in this chapter come directly from the MIB-II itself.

The notes that follow the descriptions refer to Brocade-specific information and are provided by

Brocade.


53-1001156-01

13

2

MIB-II Object Hierarchy


Figure 6 through

Figure 15

depicts the organization and structure of MIB-II.

- iso

- org

- dod

- internet

- directory

- mgmt

- mib-2

- system

- interfaces

- at

- ip

- icmp

- tcp

- udp

- egp

- transmission

- snmp

- iFMIB

FIGURE 6

MIB-II Overall Hierarchy

- system (1.3.6.1.2.1.1)

- sysDescr 1.3.6.1.2.1.1.1

- sysObjectID 1.3.6.1.2.1.1.2

- sysUpTime 1.3.6.1.2.1.1.3

- sysContact 1.3.6.1.2.1.1.4

- sysName 1.3.6.1.2.1.1.5

- sysLocation 1.3.6.1.2.1.1.6

- sysServices 1.3.6.1.2.1.1.7

FIGURE 7

System Hierarchy


53-1001156-01


53-1001156-01

- interfaces (1.3.6.1.2.1.2)

- ifNumber 1.3.6.1.2.1.2.1

- ifTable 1.3.6.1.2.1.2.2

- ifEntry 1.3.6.1.2.1.2.2.1

- ifIndex 1.3.6.1.2.1.2.2.1.1

- ifDescr 1.3.6.1.2.1.2.2.1.2

- ifType 1.3.6.1.2.1.2.2.1.3

- ifMtu 1.3.6.1.2.1.2.2.1.4

- ifSpeed 1.3.6.1.2.1.2.2.1.5

- ifPhysAddress 1.3.6.1.2.1.2.2.1.6

- ifAdminStatus 1.3.6.1.2.1.2.2.1.7

- ifOperStatus 1.3.6.1.2.1.2.2.1.8

- ifLastChange 1.3.6.1.2.1.2.2.1.9

- ifInOctets 1.3.6.1.2.1.2.2.1.10

- ifInUcastPkts 1.3.6.1.2.1.2.2.1.11

- ifInNUcastPkts 1.3.6.1.2.1.2.2.1.12

- ifInDiscards 1.3.6.1.2.1.2.2.1.13

- ifInErrors 1.3.6.1.2.1.2.2.1.14

- ifInUnknownProtos 1.3.6.1.2.1.2.2.1.15

- ifOutOctets 1.3.6.1.2.1.2.2.1.16

- ifOutUcastPkts 1.3.6.1.2.1.2.2.1.17

- ifOutNUcastPkts 1.3.6.1.2.1.2.2.1.18

- ifOutDiscards 1.3.6.1.2.1.2.2.1.19

- ifOutErrors 1.3.6.1.2.1.2.2.1.20

- ifOutQLen 1.3.6.1.2.1.2.2.1.21

- ifSpecific 1.3.6.1.2.1.2.2.1.22

- ifOutUcastPkts 1.3.6.1.2.1.2.2.1.17

- ifOutNUcastPkts 1.3.6.1.2.1.2.2.1.18

- ifOutDiscards 1.3.6.1.2.1.2.2.1.19

- ifOutErrors 1.3.6.1.2.1.2.2.1.20

- ifOutQLen 1.3.6.1.2.1.2.2.1.21

- ifSpecific 1.3.6.1.2.1.2.2.1.22

FIGURE 8

Interfaces Hierarchy

- at (1.3.6.1.2.1.3)

- atTable 1.3.6.1.2.1.3.1

- atEntry 1.3.6.1.2.1.3.1.1

- atIfIndex 1.3.6.1.2.1.3.1.1.1

- atPhysAddress 1.3.6.1.2.1.3.1.1.2

- atNetAddress 1.3.6.1.2.1.3.1.1.3

FIGURE 9

AT Hierarchy


2

15

16

2


- ip (1.3.6.1.2.1.4)

- ipForwarding 1.3.6.1.2.1.4.1

- ipDefaultTTL 1.3.6.1.2.1.4.2

- ipInReceives 1.3.6.1.2.1.4.3

- ipInHdrErrors 1.3.6.1.2.1.4.4

- ipInAddrErrors 1.3.6.1.2.1.4.5

- ipForwDatagrams 1.3.6.1.2.1.4.6

- ipInUnknownProtos 1.3.6.1.2.1.4.7

- ipInDiscards 1.3.6.1.2.1.4.8

- ipInDelivers 1.3.6.1.2.1.4.9

- ipOutRequests 1.3.6.1.2.1.4.10

- ipOutDiscards 1.3.6.1.2.1.4.11

- ipOutNoRoutes 1.3.6.1.2.1.4.12

- ipReasmTimeout 1.3.6.1.2.1.4.13

- ipReasmReqds 1.3.6.1.2.1.4.14

- ipReasmOKs 1.3.6.1.2.1.4.15

- ipReasmFails 1.3.6.1.2.1.4.16

- ipFragOKs 1.3.6.1.2.1.4.17

- ipFragFails 1.3.6.1.2.1.4.18

- ipFragCreates 1.3.6.1.2.1.4.19

- ipAddrTable 1.3.6.1.2.1.4.20

- ipAddrEntry 1.3.6.1.2.1.4.20.1

- ipAdEntAddr 1.3.6.1.2.1.4.20.1.1

- ipAdEntIfIndex 1.3.6.1.2.1.4.20.1.2

- ipAdEntNetMask 1.3.6.1.2.1.4.20.1.3

- ipAdEntBcastAddr 1.3.6.1.2.1.4.20.1.4

- ipAdEntReasmMaxSize 1.3.6.1.2.1.4.20.1.5

- ipRouteTable 1.3.6.1.2.1.4.21

- ipRouteEntry 1.3.6.1.2.1.4.21.1

- ipRouteDest 1.3.6.1.2.1.4.21.1.1

- ipRouteIfIndex 1.3.6.1.2.1.4.21.1.2

- ipRouteMetric1 1.3.6.1.2.1.4.21.1.3

- ipRouteMetric2 1.3.6.1.2.1.4.21.1.4

- ipRouteMetric3 1.3.6.1.2.1.4.21.1.5

- ipRouteMetric4 1.3.6.1.2.1.4.21.1.6

- ipRouteNextHop 1.3.6.1.2.1.4.21.1.7

- ipRouteType 1.3.6.1.2.1.4.21.1.8

- ipRouteProto 1.3.6.1.2.1.4.21.1.9

- ipRouteAge 1.3.6.1.2.1.4.21.1.10

- ipRouteMask 1.3.6.1.2.1.4.21.1.11

- ipRouteMetric5 1.3.6.1.2.1.4.21.1.12

- ipRouteInfo 1.3.6.1.2.1.4.21.1.13

- ipNetToMediaTable 1.3.6.1.2.1.4.22

- ipNetToMediaEntry 1.3.6.1.2.1.4.22.1

- ipNetToMediaIfIndex 1.3.6.1.2.1.4.22.1.1

- ipNetToMediaPhysAddress 1.3.6.1.2.1.4.22.1.2

- ipNetToMediaNetAddress 1.3.6.1.2.1.4.22.1.3

- ipNetToMediaType 1.3.6.1.2.1.4.22.1.4

- ipRoutingDiscards 1.3.6.1.2.1.4.23

FIGURE 10

IP Hierarchy


53-1001156-01


53-1001156-01

- icmp (1.3.6.1.2.1.5)

- icmpInMsgs 1.3.6.1.2.1.5.1

- icmpInErrors 1.3.6.1.2.1.5.2

- icmpInDestUnreachs 1.3.6.1.2.1.5.3

- icmpInTimeExcds 1.3.6.1.2.1.5.4

- icmpInParmProbs 1.3.6.1.2.1.5.5

- icmpInSrcQuenchs 1.3.6.1.2.1.5.6

- icmpInRedirects 1.3.6.1.2.1.5.7

- icmpInEchos 1.3.6.1.2.1.5.8

- icmpInEchoReps 1.3.6.1.2.1.5.9

- icmpInTimestamps 1.3.6.1.2.1.5.10

- icmpInTimestampReps 1.3.6.1.2.1.5.11

- icmpInAddrMasks 1.3.6.1.2.1.5.12

- icmpInAddrMaskReps 1.3.6.1.2.1.5.13

- icmpOutMsgs 1.3.6.1.2.1.5.14

- icmpOutErrors 1.3.6.1.2.1.5.15

- icmpOutDestUnreachs 1.3.6.1.2.1.5.16

- icmpOutTimeExcds 1.3.6.1.2.1.5.17

- icmpOutParmProbs 1.3.6.1.2.1.5.18

- icmpOutSrcQuenchs 1.3.6.1.2.1.5.19

- icmpOutRedirects 1.3.6.1.2.1.5.20

- icmpOutEchos 1.3.6.1.2.1.5.21

- icmpOutEchoReps 1.3.6.1.2.1.5.22

- icmpOutTimestamps 1.3.6.1.2.1.5.23

- icmpOutTimestampReps 1.3.6.1.2.1.5.24

- icmpOutAddrMasks 1.3.6.1.2.1.5.25

- icmpOutAddrMaskReps 1.3.6.1.2.1.5.26

- icmpOutSrcQuenchs 1.3.6.1.2.1.5.19

- icmpOutRedirects 1.3.6.1.2.1.5.20

- icmpOutEchos 1.3.6.1.2.1.5.21

- icmpOutEchoReps 1.3.6.1.2.1.5.22

- icmpOutTimestamps 1.3.6.1.2.1.5.23

- icmpOutTimestampReps 1.3.6.1.2.1.5.24

- icmpOutAddrMasks 1.3.6.1.2.1.5.25

- icmpOutAddrMaskReps 1.3.6.1.2.1.5.26

FIGURE 11

ICMP Hierarchy


2

17

18

2


- tcp (1.3.6.1.2.1.6)

- tcpRtoAlgorithm 1.3.6.1.2.1.6.1

- tcpRtoMin 1.3.6.1.2.1.6.2

- tcpRtoMax 1.3.6.1.2.1.6.3

- tcpMaxConn 1.3.6.1.2.1.6.4

- tcpActiveOpens 1.3.6.1.2.1.6.5

- tcpPassiveOpens 1.3.6.1.2.1.6.6

- tcpAttemptFails 1.3.6.1.2.1.6.7

- tcpEstabResets 1.3.6.1.2.1.6.8

- tcpCurrEstab 1.3.6.1.2.1.6.9

- tcpInSegs 1.3.6.1.2.1.6.10

- tcpOutSegs 1.3.6.1.2.1.6.11

- tcpRetransSegs 1.3.6.1.2.1.6.12

- tcpConnTable 1.3.6.1.2.1.6.13

- tcpConnEntry 1.3.6.1.2.1.6.13.1

- tcpConnState 1.3.6.1.2.1.6.13.1.1

- tcpConnLocalAddress 1.3.6.1.2.1.6.13.1.2

- tcpConnLocalPort 1.3.6.1.2.1.6.13.1.3

- tcpConnRemAddress 1.3.6.1.2.1.6.13.1.4

- tcpConnRemPort 1.3.6.1.2.1.6.13.1.5

- tcpInErrs 1.3.6.1.2.1.6.14

- tcpOutRsts 1.3.6.1.2.1.6.15

FIGURE 12

TCP Hierarchy

- udp (1.3.6.1.2.1.7)

- udpInDatagrams 1.3.6.1.2.1.7.1

- udpNoPorts 1.3.6.1.2.1.7.2

- udpInErrors 1.3.6.1.2.1.7.3

- udpOutDatagrams 1.3.6.1.2.1.7.4

- udpTable 1.3.6.1.2.1.7.5

- udpEntry 1.3.6.1.2.1.7.5.1

- udpLocalAddress 1.3.6.1.2.1.7.5.1.1

- udpLocalPort 1.3.6.1.2.1.7.5.1.2

FIGURE 13

udp Hierarchy


53-1001156-01


53-1001156-01

- egp (1.3.6.1.2.1.8)

- Transmission Group

- egpInErrors

- egpOutMsgs

- egpOutErrors

- egpNeighTable

- egpNeighEntry

- egpNeighState

- egpNeighAddr

- egpNeighAs

- egpNeighInMsgs

- egpNeighInErrs

- egpNeighOutMsgs

- egpNeighOutErrs

- egpNeighInErrMsgs

- egpNeighOutErrMsgs

- egpNeighStateUps

- egpNeighStateDowns

- egpNeighIntervalHello

- egpNeighIntervalPoll

- egpNeighMode

- egpNeighEventTrigger

- egpAs

FIGURE 14

egp Hierarchy

- snmp (1.3.6.1.2.1.11)

- snmpInPkts 1.3.6.1.2.1.11.1

- snmpOutPkts 1.3.6.1.2.1.11.2

- snmpInBadVersions 1.3.6.1.2.1.11.3

- snmpInBadCommunityNames 1.3.6.1.2.1.11.4

- snmpInBadCommunityUses 1.3.6.1.2.1.11.5

- snmpInASNParseErrs 1.3.6.1.2.1.11.6

- snmpInTooBigs 1.3.6.1.2.1.11.8

- snmpInNoSuchNames 1.3.6.1.2.1.11.9

- snmpInBadValues 1.3.6.1.2.1.11.10

- snmpInReadOnlys 1.3.6.1.2.1.11.11

- snmpInGenErrs 1.3.6.1.2.1.11.12

- snmpInTotalReqVars 1.3.6.1.2.1.11.13

- snmpInTotalSetVars 1.3.6.1.2.1.11.14

- snmpInGetRequests 1.3.6.1.2.1.11.15

- snmpInGetNexts 1.3.6.1.2.1.11.16

- snmpInSetRequests 1.3.6.1.2.1.11.17

- snmpInGetResponses 1.3.6.1.2.1.11.18

- snmpInTraps 1.3.6.1.2.1.11.19

- snmpOutTooBigs 1.3.6.1.2.1.11.20

- snmpOutNoSuchNames 1.3.6.1.2.1.11.21

- snmpOutBadValues 1.3.6.1.2.1.11.22

- snmpOutGenErrs 1.3.6.1.2.1.11.24

- snmpOutGetRequests 1.3.6.1.2.1.11.25

- snmpOutGetNexts 1.3.6.1.2.1.11.26

- snmpOutSetRequests 1.3.6.1.2.1.11.27

- snmpOutGetResponses 1.3.6.1.2.1.11.28

- snmpOutTraps 1.3.6.1.2.1.11.29

- snmpEnableAuthenTraps 1.3.6.1.2.1.11.30

FIGURE 15

snmp Hierarchy


2

19

20

2


- ifMIB (1.3.6.1.2.1.31)

- ifXTable 1.3.6.1.2.1.31.1.1

- ifXentry 1.3.6.1.2.1.31.1.1.1

- ifName 1.3.6.1.2.1.31.1.1.1.1

- ifInMulticastPkts 1.3.6.1.2.1.31.1.1.1.2

- ifInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.3

- ifOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.4

- ifOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.5

- ifHCInOctets 1.3.6.1.2.1.31.1.1.1.6

- ifHCInUcastPkts 1.3.6.1.2.1.31.1.1.1.7

- ifHCInMulticastPkts 1.3.6.1.2.1.31.1.1.1.8

- ifHCInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.9

- ifHCOutOctets 1.3.6.1.2.1.31.1.1.1.10

- ifHCOutUcastPkts 1.3.6.1.2.1.31.1.1.1.11

- ifHCOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.12

- ifHCOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.13

- ifLinkUpDownTrapEnable 1.3.6.1.2.1.31.1.1.1.14

- ifHigfSpeed 1.3.6.1.2.1.31.1.1.1.15

- ifPromiscuousMode 1.3.6.1.2.1.31.1.1.1.16

- ifConnectorPresent 1.3.6.1.2.1.31.1.1.1.17

- ifAlias 1.3.6.1.2.1.31.1.1.1.18

- ifCounterDiscontinuityTime 1.3.6.1.2.1.31.1.1.1.17

FIGURE 16

ifMIB Hierarchy


53-1001156-01

Textual Conventions

Table 5

lists the textual conventions used for MIB-II.

TABLE 5

Type Definition

MIB-II Textual Conventions

Value

DisplayString

PhysAddress

Octet String of size 0 to 255

Octet String

Objects and Types Imported

The following objects and types are imported from RFC1155-SMI:

• mgmt

•

NetworkAddress

•

IpAddress

•

Counter

•

Gauge

•

TimeTicks

Textual Conventions

2


53-1001156-01

21

2

System Group

System Group

All systems must implement the System Group. If an agent is not configured to have a value for any of the System Group variables, a string of length 0 is returned.

sysDescr 1.3.6.1.2.1.1.1

Format

Set command

Default

A textual description of the entity. This value should include the full name and version identification of the hardware type, software operating system, and networking software.

This must contain only printable ASCII characters.

Set this value using the snmpconfig command.

The switch type. The default value is either Fibre Channel Switch or Access Gateway.


53-1001156-01

sysObjectID 1.3.6.1.2.1.1.2

2 sysObjectID 1.3.6.1.2.1.1.2

Example

Default

The vendor’s authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining what kind of device is being managed.

If a vendor “NetYarn, Inc.” was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier

1.3.6.1.4.1.4242.1.1 to its “Knit Router”.

The device type. The default value is either:

•

Fibre Channel Switches: iso.org.dod.internet.private.enterprises.bcsi.commDev.fibrechannel.fcSwitch.sw

•

Brocade Access Gateway: iso.org.dod.internet.private.enterprises.bcsi.commDev.fibrechannel.fcSwitch.sw


53-1001156-01

23

2 sysUpTime 1.3.6.1.2.1.1.3

sysUpTime 1.3.6.1.2.1.1.3

Set command

The time (in hundredths of a second) since the network management portion of the system was last reinitialized.

Set this value using the switchuptime command.


53-1001156-01

sysContact 1.3.6.1.2.1.1.4

2 sysContact 1.3.6.1.2.1.1.4

Default

Set command

The textual identification of the contact person for this managed node, together with information on how to contact this person.

Field Support



53-1001156-01

25

2 sysName 1.3.6.1.2.1.1.5

sysName 1.3.6.1.2.1.1.5

Default

Set command

An administratively assigned name for this managed node. By convention, this is the node’s fully qualified domain name.

Preassigned name of the logical switch.



53-1001156-01

sysLocation 1.3.6.1.2.1.1.6

2 sysLocation 1.3.6.1.2.1.1.6

Default

Set command

The physical location of this node (for example, telephone closet, 3rd floor).

End User Premise



53-1001156-01

27

2 sysServices 1.3.6.1.2.1.1.7

sysServices 1.3.6.1.2.1.1.7

Calculate

A value that indicates the set of services that this entity primarily offers.The value is a sum. This sum initially takes the value 0. Then, for each layer, L, in the range 1 through 7, for which this node performs transactions, 2 raised to (L - 1) is added to the sum. For example, a node that primarily performs routing functions has a value of 4 (2 application services has a value of 72 (2

4-1

3-1

+ 2

). In contrast, a node that is a host and offers

7-1

).

In the context of the Internet suite of protocols, values should be calculated accordingly:

Layer functionality

1 = physical (for example, repeaters)

2 = datalink/subnetwork (for example, bridges)

3 = internet (for example, IP gateways)

4 = end-to-end (for example, IP hosts)

7 = applications (for example, mail relays)

For systems including OSI protocols, layers 5 and 6 also can be counted. The return value is always

79.


53-1001156-01

Interfaces Group

2

Interfaces Group

Implementation of the Interfaces group is mandatory for all systems. FCIP tunnel support is added in Fabric OS 5.3.0 and higher. To support FCIP tunneling, entries are created in the ifTable for each

WAN interface (GbE port), each FC port, and each FCIP tunnel (transport interface).

Logical Inter Switch Link (LISL) is an FC interface.


53-1001156-01

29

2 ifNumber 1.3.6.1.2.1.2.1

ifNumber 1.3.6.1.2.1.2.1

The number of network interfaces and existing FC ports present on this system, regardless of their current state. This number will vary across platforms (switches).

The return value is dynamic for all Brocade switches and depends on the number of GbE ports, FC ports and transport interfaces.


53-1001156-01

ifTable 1.3.6.1.2.1.2.2

2 ifTable 1.3.6.1.2.1.2.2

A list of interface entries. The number of entries is given by the value of ifNumber.

The Interfaces table contains information on the entity’s interfaces. Each interface is thought of as being attached to a subnetwork. Note that this term should not be confused with subnet, which refers to an addressing partitioning scheme used in the Internet suite of protocols.


53-1001156-01

31

2 ifEntry 1.3.6.1.2.1.2.2.1

ifEntry 1.3.6.1.2.1.2.2.1

Index

An interface entry containing objects at the subnetwork layer and below, for a particular interface. ifIndex


53-1001156-01

ifIndex 1.3.6.1.2.1.2.2.1.1

2 ifIndex 1.3.6.1.2.1.2.2.1.1

A unique value for each interface.

The values range between 1 and the value of ifNumber. The value for each interface must remain constant, at least from one reinitialization of the entity's network management system to the next reinitialization.

For Network Interface, the number starts from 805306369 and increments with the interface count. For FC Ports, the number starts from 1073741824 and increments with the existing FC

Ports.


53-1001156-01

33

2 ifDescr 1.3.6.1.2.1.2.2.1.2

ifDescr 1.3.6.1.2.1.2.2.1.2

Values

A textual string containing information about the interface. The ifDescr for non-bladed switches includes: lo, eth0, and fc0. The ifDescr for Brocade 12000, 24000, and 48000 directors includes: lo, eth0, fc0, and sit0, as well as fc1, eth0:1, and eth0:2.

•

For WAN interface- GigE port for FCIP

•

For transport interface- fcip tunnel ID

•

For FC ports- Port name (if set), otherwise, FC Port <slot/port>


53-1001156-01

ifType 1.3.6.1.2.1.2.2.1.3

2 ifType 1.3.6.1.2.1.2.2.1.3

Values

The type of interface, designated by the physical/link protocol(s) immediately below the network layer in the protocol stack.

•

For WAN interface, FCIP Link- ethernetCsmacd (6)

•

For transport interface-fcipLink(224)

•

For FC ports- fibre channel (56)


53-1001156-01

35

2 ifMtu 1.3.6.1.2.1.2.2.1.4

ifMtu 1.3.6.1.2.1.2.2.1.4

Values

The size of the largest datagram that can be sent/received on the interface, specified in octets.

For interfaces that are used to transmit network datagrams, the value is the size of the largest network datagram that can be sent on the interface (these values are different for Fabric OS v4.x).

• eth0 returns 1500

• lo returns 16436

• fc0 returns 2024

•

FCIP GIGE returns 1500

• sit0 returns 1480

• fc0 returns 2024

• port0 returns 2112


53-1001156-01

ifSpeed 1.3.6.1.2.1.2.2.1.5

2 ifSpeed 1.3.6.1.2.1.2.2.1.5

Values

An estimate (in bits per second) of the interface's current bandwidth.

For interfaces that do not vary in bandwidth or interfaces for which no accurate estimation can be made, this object should contain the nominal bandwidth. For Fabric OS v4.x, 2 Gbps returns.

• eth0 returns null

• lo returns 1,000,000,000 for 1G

• fc0 returns 2000000000 for 2Gbps port

• fc0 returns 4000000000 for 4Gbps port

•

For 10G: Value displayed will be 4294967295

•

For 8G: Value displayed will be 4294967294


53-1001156-01

37

2 ifPhysAddress 1.3.6.1.2.1.2.2.1.6

ifPhysAddress 1.3.6.1.2.1.2.2.1.6

Values

The interface's address at the protocol layer immediately below the network layer in the protocol stack.

For interfaces that do not have such an address (for example, a serial line), this object should contain an octet string of zero length.

• eth0 returns the Mac address for GiGE ports

• lo returns null

• fc0 returns the Fibre Channel address ID (24-bit Domain:Area:Port format) which is PID


53-1001156-01

ifAdminStatus 1.3.6.1.2.1.2.2.1.7

2 ifAdminStatus 1.3.6.1.2.1.2.2.1.7

Values

The desired state of the interface.

• up (1)

• down (2) or

• testing (3)

Supports Read only, should return same value with ifOperStatus for WAN and FC ports interfaces.

NOTE

The 3 state (testing) indicates that no operational packets can be passed. This object is read-only in

Fabric OS v4.x and above.


53-1001156-01

39

2 ifOperStatus 1.3.6.1.2.1.2.2.1.8

ifOperStatus 1.3.6.1.2.1.2.2.1.8

Values

The current operational state of the interface.

• up (1)

• down (2) or

• testing (3?)

Active tunnels will be up; inactive tunnels will be down (configured but not online).

NOTE

.The 3 state (testing) indicates that no operational packets can be passed.


53-1001156-01

ifLastChange 1.3.6.1.2.1.2.2.1.9

2 ifLastChange 1.3.6.1.2.1.2.2.1.9

The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.


53-1001156-01

41

2 ifInOctets 1.3.6.1.2.1.2.2.1.10

ifInOctets 1.3.6.1.2.1.2.2.1.10

The total number of octets received on the interface, including framing characters.


53-1001156-01

ifInUcastPkts 1.3.6.1.2.1.2.2.1.11

2 ifInUcastPkts 1.3.6.1.2.1.2.2.1.11

The number of subnetwork-unicast packets delivered to a higher-layer protocol.

Not supported.


53-1001156-01

43

2 ifInNUcastPkts 1.3.6.1.2.1.2.2.1.12

ifInNUcastPkts 1.3.6.1.2.1.2.2.1.12

The number of nonunicast packets (for example, subnetwork-broadcast or subnetwork-multicast) delivered to a higher-layer protocol.

Not supported.


53-1001156-01

ifInDiscards 1.3.6.1.2.1.2.2.1.13

2 ifInDiscards 1.3.6.1.2.1.2.2.1.13

The number of inbound packets that were chosen to be discarded (even though no errors had been detected) to prevent their being deliverable to a higher-layer protocol.

One possible reason for discarding such a packet could be to free buffer space.


53-1001156-01

45

2 ifInErrors 1.3.6.1.2.1.2.2.1.14

ifInErrors 1.3.6.1.2.1.2.2.1.14

The number of inbound packets that contained errors, which thereby prevented them from being deliverable to a higher-layer protocol.


53-1001156-01

ifInUnknownProtos 1.3.6.1.2.1.2.2.1.15

2 ifInUnknownProtos 1.3.6.1.2.1.2.2.1.15

The number of packets received by way of the interface that were discarded because of an unknown or unsupported protocol.

Not supported.


53-1001156-01

47

2 ifOutOctets 1.3.6.1.2.1.2.2.1.16

ifOutOctets 1.3.6.1.2.1.2.2.1.16

The total number of octets transmitted out of the interface, including framing characters.


53-1001156-01

ifOutUcastPkts 1.3.6.1.2.1.2.2.1.17

2 ifOutUcastPkts 1.3.6.1.2.1.2.2.1.17

The total number of packets that were requested, by higher-level protocols, to be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.

Not supported.


53-1001156-01

49

2 ifOutNUcastPkts 1.3.6.1.2.1.2.2.1.18

ifOutNUcastPkts 1.3.6.1.2.1.2.2.1.18

The total number of packets that were requested, by higher-level protocols, to be transmitted to a nonunicast address (for example, a subnetwork-broadcast or subnetwork-multicast), including those that were discarded or not sent.

Not supported.


53-1001156-01

ifOutDiscards 1.3.6.1.2.1.2.2.1.19

ifOutDiscards 1.3.6.1.2.1.2.2.1.19

The number of outbound packets that were chosen to be discarded (even though no errors had been detected) to prevent their being transmitted. One possible reason for discarding such a packet could be to free buffer space.

2


53-1001156-01

51

2 ifOutErrors 1.3.6.1.2.1.2.2.1.20

ifOutErrors 1.3.6.1.2.1.2.2.1.20

The number of outbound packets that could not be transmitted because of errors.


53-1001156-01

ifOutQLen 1.3.6.1.2.1.2.2.1.21

The length of the output packet queue (in packets).

Not supported.

ifOutQLen 1.3.6.1.2.1.2.2.1.21

2


53-1001156-01

53

2 ifSpecific 1.3.6.1.2.1.2.2.1.22

ifSpecific 1.3.6.1.2.1.2.2.1.22

Returns

A reference to MIB definitions specific to the particular media being used to realize the interface.

If the interface is realized by an Ethernet, then the value of this object refers to a document defining objects specific to Ethernet. If this information is not present, its value should be set to the

Object Identifier 0 0, which is a syntactically valid object identifier, and any conferment implementation of ASN.1 and BER must be able to generate and recognize this value.

• eth0 returns null OID

• lo returns null OID

• fc0 returns null OID


53-1001156-01

AT Group

2

AT Group

Implementation of the Address Translation group is mandatory for all systems. Note, however, that this group is deprecated by MIB-II. From MIB-II onward, each network protocol group contains its own address translation tables.


53-1001156-01

55

2 atTable 1.3.6.1.2.1.3.1

atTable 1.3.6.1.2.1.3.1

The Address Translation group contains one table, which is the union across all interfaces of the translation tables for converting a network address (for example, an IP address) into a subnetwork-specific address. This document refers to such a subnetwork-specific address as a

physical address.

For example, for broadcast media, where ARP is in use, the translation table is equivalent to the

ARP cache; on an X.25 network, where non-algorithmic translation to X.121 addresses is required, the translation table contains the network address to X.121 address equivalences.

The Address Translation tables contain the network address to physical address equivalences.

Some interfaces do not use translation tables for determining address equivalences (for example,

DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty.


53-1001156-01

atEntry 1.3.6.1.2.1.3.1.1

2 atEntry 1.3.6.1.2.1.3.1.1

Index

Each entry contains one network address to physical address equivalence.

atIfIndex, atNetAddress


53-1001156-01

57

2 atIfIndex 1.3.6.1.2.1.3.1.1.1

atIfIndex 1.3.6.1.2.1.3.1.1.1

The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.


53-1001156-01

atPhysAddress 1.3.6.1.2.1.3.1.1.2

The media-dependent physical address.

atPhysAddress 1.3.6.1.2.1.3.1.1.2

2


53-1001156-01

59

2 atNetAddress 1.3.6.1.2.1.3.1.1.3

atNetAddress 1.3.6.1.2.1.3.1.1.3

The network address (for example, the IP address) corresponding to the media-dependent physical address.


53-1001156-01

IP Group

Implementation of the IP group is mandatory for all systems.

IP Group

2


53-1001156-01

61

2 ipForwarding 1.3.6.1.2.1.4.1

ipForwarding 1.3.6.1.2.1.4.1

The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams; IP hosts do not (except those source-routed through the host).


53-1001156-01

ipDefaultTTL 1.3.6.1.2.1.4.2

2 ipDefaultTTL 1.3.6.1.2.1.4.2

The default value inserted into the time-to-live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.


53-1001156-01

63

2 ipInReceives 1.3.6.1.2.1.4.3

ipInReceives 1.3.6.1.2.1.4.3

The total number of input datagrams received from interfaces, including those received in error.


53-1001156-01

ipInHdrErrors 1.3.6.1.2.1.4.4

2 ipInHdrErrors 1.3.6.1.2.1.4.4

The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, and so on.


53-1001156-01

65

2 ipInAddrErrors 1.3.6.1.2.1.4.5

ipInAddrErrors 1.3.6.1.2.1.4.5

The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (for example, 0.0.0.0) and addresses of unsupported classes (for example, Class E). For entities that are not IP gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.


53-1001156-01

ipForwDatagrams 1.3.6.1.2.1.4.6

2 ipForwDatagrams 1.3.6.1.2.1.4.6

The number of input datagrams for which this entity was not final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities that do not act as IP gateways, this counter includes only those packets that were source-routed through this entity, and the Source-Route option processing was successful.


53-1001156-01

67

2 ipInUnknownProtos 1.3.6.1.2.1.4.7

ipInUnknownProtos 1.3.6.1.2.1.4.7

The number of locally addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.


53-1001156-01

ipInDiscards 1.3.6.1.2.1.4.8

2 ipInDiscards 1.3.6.1.2.1.4.8

The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (for example, for lack of buffer space).

This counter does not include any datagrams discarded while awaiting reassembly.


53-1001156-01

69

2 ipInDelivers 1.3.6.1.2.1.4.9

ipInDelivers 1.3.6.1.2.1.4.9

The total number of input datagrams successfully delivered to IP user protocols (including ICMP).


53-1001156-01

ipOutRequests 1.3.6.1.2.1.4.10

ipOutRequests 1.3.6.1.2.1.4.10

The total number of IP datagrams that local IP user protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.

2


53-1001156-01

71

2 ipOutDiscards 1.3.6.1.2.1.4.11

ipOutDiscards 1.3.6.1.2.1.4.11

The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (for example, for lack of buffer space).

NOTE

This counter would include datagrams counted in ipForwDatagrams if any such packets met this

(discretionary) discard criterion.


53-1001156-01

ipOutNoRoutes 1.3.6.1.2.1.4.12

2 ipOutNoRoutes 1.3.6.1.2.1.4.12

The number of IP datagrams discarded because no route could be found to transmit them to their destination.

NOTE

This counter includes any packets counted in ipForwDatagrams that meet this “no-route” criterion.

Note that this includes any datagrams that a host cannot route because all of its default gateways are down.


53-1001156-01

73

2 ipReasmTimeout 1.3.6.1.2.1.4.13

ipReasmTimeout 1.3.6.1.2.1.4.13

The maximum number of seconds that received fragments are held while they are awaiting reassembly at this entity.


53-1001156-01

ipReasmReqds 1.3.6.1.2.1.4.14

2 ipReasmReqds 1.3.6.1.2.1.4.14

The number of IP fragments received that needed to be reassembled at this entity.


53-1001156-01

75

2 ipReasmOKs 1.3.6.1.2.1.4.15

ipReasmOKs 1.3.6.1.2.1.4.15

The number of IP datagrams successfully reassembled.


53-1001156-01

ipReasmFails 1.3.6.1.2.1.4.16

2 ipReasmFails 1.3.6.1.2.1.4.16

The number of failures detected by the IP reassembly algorithm (for whatever reason: timed out, errors, and so on).

NOTE

This is not necessarily a count of discarded IP fragments, because some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.


53-1001156-01

77

2 ipFragOKs 1.3.6.1.2.1.4.17

ipFragOKs 1.3.6.1.2.1.4.17

The number of IP datagrams that have been successfully fragmented at this entity.


53-1001156-01

ipFragFails 1.3.6.1.2.1.4.18

2 ipFragFails 1.3.6.1.2.1.4.18

The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be (for example, because their Don't Fragment flag was set).


53-1001156-01

79

2 ipFragCreates 1.3.6.1.2.1.4.19

ipFragCreates 1.3.6.1.2.1.4.19

The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.


53-1001156-01

ipAddrTable 1.3.6.1.2.1.4.20

2 ipAddrTable 1.3.6.1.2.1.4.20

The table of addressing information relevant to this entity's IP addresses.


53-1001156-01

81

2 ipAddrEntry 1.3.6.1.2.1.4.20.1

ipAddrEntry 1.3.6.1.2.1.4.20.1

Index

The addressing information for one of this entity's IP addresses.

ipAdEntAddr


53-1001156-01

ipAdEntAddr 1.3.6.1.2.1.4.20.1.1

2 ipAdEntAddr 1.3.6.1.2.1.4.20.1.1

The IP address to which this entry's addressing information pertains.


53-1001156-01

83

2 ipAdEntIfIndex 1.3.6.1.2.1.4.20.1.2

ipAdEntIfIndex 1.3.6.1.2.1.4.20.1.2

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.


53-1001156-01

ipAdEntNetMask 1.3.6.1.2.1.4.20.1.3

2 ipAdEntNetMask 1.3.6.1.2.1.4.20.1.3

The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.


53-1001156-01

85

2 ipAdEntBcastAddr 1.3.6.1.2.1.4.20.1.4

ipAdEntBcastAddr 1.3.6.1.2.1.4.20.1.4

The value of the least-significant bit in the IP broadcast address used for sending datagrams on the

(logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.


53-1001156-01

ipAdEntReasmMaxSize 1.3.6.1.2.1.4.20.1.5

2 ipAdEntReasmMaxSize 1.3.6.1.2.1.4.20.1.5

The size of the largest IP datagram that this entity can reassemble from incoming IP fragmented datagrams received on this interface.


53-1001156-01

87

2 ipRouteTable 1.3.6.1.2.1.4.21

ipRouteTable 1.3.6.1.2.1.4.21

The IP routing table contains an entry for each route currently known to this entity.


53-1001156-01

ipRouteEntry 1.3.6.1.2.1.4.21.1

Index

A route to a particular destination.

ipRouteDest ipRouteEntry 1.3.6.1.2.1.4.21.1

2


53-1001156-01

89

2 ipRouteDest 1.3.6.1.2.1.4.21.1.1

ipRouteDest 1.3.6.1.2.1.4.21.1.1

The destination IP address of this route.

An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.


53-1001156-01

ipRouteIfIndex 1.3.6.1.2.1.4.21.1.2

2 ipRouteIfIndex 1.3.6.1.2.1.4.21.1.2

The index value that uniquely identifies the local interface through which the next hop of this route should be reached.

The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex.


53-1001156-01

91

2 ipRouteMetric1 1.3.6.1.2.1.4.21.1.3

ipRouteMetric1 1.3.6.1.2.1.4.21.1.3

The primary routing metric for this route.

The semantics of this metric are determined by the routing protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.


53-1001156-01

ipRouteMetric2 1.3.6.1.2.1.4.21.1.4

2 ipRouteMetric2 1.3.6.1.2.1.4.21.1.4

An alternate routing metric for this route.



53-1001156-01

93

2 ipRouteMetric3 1.3.6.1.2.1.4.21.1.5

ipRouteMetric3 1.3.6.1.2.1.4.21.1.5




53-1001156-01

ipRouteMetric4 1.3.6.1.2.1.4.21.1.6

2 ipRouteMetric4 1.3.6.1.2.1.4.21.1.6




53-1001156-01

95

2 ipRouteNextHop 1.3.6.1.2.1.4.21.1.7

ipRouteNextHop 1.3.6.1.2.1.4.21.1.7

The IP address of the next hop of this route. (In the case of a route bound to an interface that is realized through a broadcast media, the value of this field is the agent’s IP address on that interface.)


53-1001156-01

ipRouteType 1.3.6.1.2.1.4.21.1.8

2 ipRouteType 1.3.6.1.2.1.4.21.1.8

Valid values

The type of route. Setting this object to 2 (invalid) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.

The values direct (3) and indirect (4) refer to the notion of direct and indirect routing in the IP architecture.

other (1) invalid (2) direct (3) indirect (4)

None of the following

An invalidated route—route to directly

Connected (sub)network—route to a non-local

Host/network/subnetwork


53-1001156-01

97

2 ipRouteProto 1.3.6.1.2.1.4.21.1.9

ipRouteProto 1.3.6.1.2.1.4.21.1.9

The routing mechanism by which this route was learned.

Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.


53-1001156-01

ipRouteAge 1.3.6.1.2.1.4.21.1.10

2 ipRouteAge 1.3.6.1.2.1.4.21.1.10

The number of seconds since this route was last updated or otherwise determined to be correct.

Older semantics cannot be implied except through knowledge of the routing protocol by which the route was learned.


53-1001156-01

99

2 ipRouteMask 1.3.6.1.2.1.4.21.1.11

ipRouteMask 1.3.6.1.2.1.4.21.1.11

The mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of the following: mask

255.0.0.0 network class-A

255.255.0.0 class-B

255.255.255.0 class-C

NOTE

If the value of the ipRouteDest is 0.0.0.0 (default route), then the mask value is also 0.0.0.0.

All IP routing subsystems implicitly use this mechanism.


53-1001156-01

ipRouteMetric5 1.3.6.1.2.1.4.21.1.12

2 ipRouteMetric5 1.3.6.1.2.1.4.21.1.12




53-1001156-01

101

2 ipRouteInfo 1.3.6.1.2.1.4.21.1.13

ipRouteInfo 1.3.6.1.2.1.4.21.1.13

A reference to MIB definitions specific to the particular routing protocol that is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the Object Identifier { 0 0 }, which is a syntactically valid object identifier; any conferment implementation of ASN.1 and BER must be able to generate and recognize this value.


53-1001156-01

ipNetToMediaTable 1.3.6.1.2.1.4.22

2 ipNetToMediaTable 1.3.6.1.2.1.4.22

The IP Address Translation table used for mapping from IP addresses to physical addresses.

NOTE

The IP address translation table contains the IP address to physical address equivalences. Some interfaces do not use translation tables for determining address equivalences. For example,

DDN-X.25 has an algorithmic method; if all interfaces are of this type, then the Address Translation table is empty.


53-1001156-01

103

2 ipNetToMediaEntry 1.3.6.1.2.1.4.22.1

ipNetToMediaEntry 1.3.6.1.2.1.4.22.1

Index

Each entry contains one IP address to physical address equivalence.

ipNetToMediaIfIndex, ipNetToMediaNetAddress


53-1001156-01

ipNetToMediaIfIndex 1.3.6.1.2.1.4.22.1.1

2 ipNetToMediaIfIndex 1.3.6.1.2.1.4.22.1.1

The interface on which this entry's equivalence is effective.

The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex.


53-1001156-01

105

2 ipNetToMediaPhysAddress 1.3.6.1.2.1.4.22.1.2

ipNetToMediaPhysAddress 1.3.6.1.2.1.4.22.1.2

The media-dependent physical address.


53-1001156-01

ipNetToMediaNetAddress 1.3.6.1.2.1.4.22.1.3

2 ipNetToMediaNetAddress 1.3.6.1.2.1.4.22.1.3

The IpAddress corresponding to the media-dependent physical address.


53-1001156-01

107

2 ipNetToMediaType 1.3.6.1.2.1.4.22.1.4

ipNetToMediaType 1.3.6.1.2.1.4.22.1.4

The type of mapping.


53-1001156-01

ipRoutingDiscards 1.3.6.1.2.1.4.23

2 ipRoutingDiscards 1.3.6.1.2.1.4.23

The number of routing entries discarded even though they are valid. One possible reason for discarding such an entry could be to free buffer space for other routing entries.


53-1001156-01

109

2

ICMP Group

ICMP Group

Implementation of the ICMP group is mandatory for all systems.


53-1001156-01

icmpInMsgs 1.3.6.1.2.1.5.1

2 icmpInMsgs 1.3.6.1.2.1.5.1

The total number of ICMP messages that the entity received.

This counter includes all ICMP messages counted by icmpInErrors.


53-1001156-01

111

2 icmpInErrors 1.3.6.1.2.1.5.2

icmpInErrors 1.3.6.1.2.1.5.2

The number of ICMP messages that the entity received but determined to have ICMP-specific errors

(bad ICMP checksums, bad length, and so on).


53-1001156-01

icmpInDestUnreachs 1.3.6.1.2.1.5.3

2 icmpInDestUnreachs 1.3.6.1.2.1.5.3

The number of ICMP Destination Unreachable messages received.


53-1001156-01

113

2 icmpInTimeExcds 1.3.6.1.2.1.5.4

icmpInTimeExcds 1.3.6.1.2.1.5.4

The number of ICMP Time Exceeded messages received.


53-1001156-01

icmpInParmProbs 1.3.6.1.2.1.5.5

2 icmpInParmProbs 1.3.6.1.2.1.5.5

The number of ICMP Parameter Problem messages received.


53-1001156-01

115

2 icmpInSrcQuenchs 1.3.6.1.2.1.5.6

icmpInSrcQuenchs 1.3.6.1.2.1.5.6

The number of ICMP Source Quench messages received.


53-1001156-01

icmpInRedirects 1.3.6.1.2.1.5.7

The number of ICMP Redirect messages received.

icmpInRedirects 1.3.6.1.2.1.5.7

2


53-1001156-01

117

2 icmpInEchos 1.3.6.1.2.1.5.8

icmpInEchos 1.3.6.1.2.1.5.8

The number of ICMP Echo (request) messages received.


53-1001156-01

icmpInEchoReps 1.3.6.1.2.1.5.9

The number of ICMP Echo Reply messages received.

icmpInEchoReps 1.3.6.1.2.1.5.9

2


53-1001156-01

119

2 icmpInTimestamps 1.3.6.1.2.1.5.10

icmpInTimestamps 1.3.6.1.2.1.5.10

The number of ICMP Timestamp (request) messages received.


53-1001156-01

icmpInTimestampReps 1.3.6.1.2.1.5.11

2 icmpInTimestampReps 1.3.6.1.2.1.5.11

The number of ICMP Timestamp Reply messages received.


53-1001156-01

121

2 icmpInAddrMasks 1.3.6.1.2.1.5.12

icmpInAddrMasks 1.3.6.1.2.1.5.12

The number of ICMP Address Mask Request messages received.


53-1001156-01

icmpInAddrMaskReps 1.3.6.1.2.1.5.13

2 icmpInAddrMaskReps 1.3.6.1.2.1.5.13

The number of ICMP Address Mask Reply messages received.


53-1001156-01

123

2 icmpOutMsgs 1.3.6.1.2.1.5.14

icmpOutMsgs 1.3.6.1.2.1.5.14

The total number of ICMP messages that this entity attempted to send.

NOTE

This counter includes all those counted by icmpOutErrors.


53-1001156-01

icmpOutErrors 1.3.6.1.2.1.5.15

2 icmpOutErrors 1.3.6.1.2.1.5.15

The number of ICMP messages that this entity did not send due to problems discovered within

ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there might be no types of error that contribute to this counter's value.


53-1001156-01

125

2 icmpOutDestUnreachs 1.3.6.1.2.1.5.16

icmpOutDestUnreachs 1.3.6.1.2.1.5.16

The number of ICMP Destination Unreachable messages sent.


53-1001156-01

icmpOutTimeExcds 1.3.6.1.2.1.5.17

2 icmpOutTimeExcds 1.3.6.1.2.1.5.17

The number of ICMP Time Exceeded messages sent.


53-1001156-01

127

2 icmpOutParmProbs 1.3.6.1.2.1.5.18

icmpOutParmProbs 1.3.6.1.2.1.5.18

The number of ICMP Parameter Problem messages sent.


53-1001156-01

icmpOutSrcQuenchs 1.3.6.1.2.1.5.19

2 icmpOutSrcQuenchs 1.3.6.1.2.1.5.19

The number of ICMP Source Quench messages sent.


53-1001156-01

129

2 icmpOutRedirects 1.3.6.1.2.1.5.20

icmpOutRedirects 1.3.6.1.2.1.5.20

The number of ICMP Redirect messages sent. For a host, this object is always 0, since hosts do not send redirects.


53-1001156-01

icmpOutEchos 1.3.6.1.2.1.5.21

The number of ICMP Echo (request) messages sent.

icmpOutEchos 1.3.6.1.2.1.5.21

2


53-1001156-01

131

2 icmpOutEchoReps 1.3.6.1.2.1.5.22

icmpOutEchoReps 1.3.6.1.2.1.5.22

The number of ICMP Echo Reply messages sent.


53-1001156-01

icmpOutTimestamps 1.3.6.1.2.1.5.23

2 icmpOutTimestamps 1.3.6.1.2.1.5.23

The number of ICMP Timestamp (request) messages sent.


53-1001156-01

133

2 icmpOutTimestampReps 1.3.6.1.2.1.5.24

icmpOutTimestampReps 1.3.6.1.2.1.5.24

The number of ICMP Timestamp Reply messages sent.


53-1001156-01

icmpOutAddrMasks 1.3.6.1.2.1.5.25

2 icmpOutAddrMasks 1.3.6.1.2.1.5.25

The number of ICMP Address Mask Request messages sent.


53-1001156-01

135

2 icmpOutAddrMaskReps 1.3.6.1.2.1.5.26

icmpOutAddrMaskReps 1.3.6.1.2.1.5.26

The number of ICMP Address Mask Reply messages sent.


53-1001156-01

TCP Group

2

TCP Group

Implementation of the TCP group is mandatory for all systems that implement the TCP.

Instances of object types that represent information about a particular TCP connection are transient; they persist only as long as the connection in question.


53-1001156-01

137

2 tcpRtoAlgorithm 1.3.6.1.2.1.6.1

tcpRtoAlgorithm 1.3.6.1.2.1.6.1

The algorithm used to determine the time-out value used for retransmitting unacknowledged octets.


53-1001156-01

tcpRtoMin 1.3.6.1.2.1.6.2

2 tcpRtoMin 1.3.6.1.2.1.6.2

The minimum value permitted by a TCP implementation for the retransmission time-out, measured in milliseconds.

More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission time-out. In particular, when the time-out algorithm is 3 (rsre), an object of this type has the semantics of the LBOUND quantity described in RFC 793.


53-1001156-01

139

2 tcpRtoMax 1.3.6.1.2.1.6.3

tcpRtoMax 1.3.6.1.2.1.6.3

The maximum value permitted by a TCP implementation for the retransmission time-out, measured in milliseconds.

More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission time-out. In particular, when the time-out algorithm is 3 (rsre), an object of this type has the semantics of the UBOUND quantity described in RFC 793.


53-1001156-01

tcpMaxConn 1.3.6.1.2.1.6.4

2 tcpMaxConn 1.3.6.1.2.1.6.4

The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1.


53-1001156-01

141

2 tcpActiveOpens 1.3.6.1.2.1.6.5

tcpActiveOpens 1.3.6.1.2.1.6.5

The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.


53-1001156-01

tcpPassiveOpens 1.3.6.1.2.1.6.6

2 tcpPassiveOpens 1.3.6.1.2.1.6.6

The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.


53-1001156-01

143

2 tcpAttemptFails 1.3.6.1.2.1.6.7

tcpAttemptFails 1.3.6.1.2.1.6.7

The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.


53-1001156-01

tcpEstabResets 1.3.6.1.2.1.6.8

tcpEstabResets 1.3.6.1.2.1.6.8

The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.

2


53-1001156-01

145

2 tcpCurrEstab 1.3.6.1.2.1.6.9

tcpCurrEstab 1.3.6.1.2.1.6.9

The number of TCP connections for which the current state is either ESTABLISHED or CLOSE-WAIT.


53-1001156-01

tcpInSegs 1.3.6.1.2.1.6.10

2 tcpInSegs 1.3.6.1.2.1.6.10

The total number of segments received, including those received in error. This count includes segments received on currently established connections.


53-1001156-01

147

2 tcpOutSegs 1.3.6.1.2.1.6.11

tcpOutSegs 1.3.6.1.2.1.6.11

The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets.


53-1001156-01

tcpRetransSegs 1.3.6.1.2.1.6.12

tcpRetransSegs 1.3.6.1.2.1.6.12

The total number of segments retransmitted; that is, the number of TCP segments transmitted containing one or more previously transmitted octets.

2


53-1001156-01

149

2

TCP Connection Table

TCP Connection Table

The TCP connection table contains information about this entity's existing TCP connections.


53-1001156-01

tcpConnTable 1.3.6.1.2.1.6.13

A table containing TCP connection-specific information.

tcpConnTable 1.3.6.1.2.1.6.13

2


53-1001156-01

151

2 tcpConnEntry 1.3.6.1.2.1.6.13.1

tcpConnEntry 1.3.6.1.2.1.6.13.1

Index

Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.

tcpConnLocalAddress, tcpConnLocalPort, tcpConnRemAddress, tcpConnRemPort


53-1001156-01

tcpConnState 1.3.6.1.2.1.6.13.1.1

2 tcpConnState 1.3.6.1.2.1.6.13.1.1

Values

The state of this TCP connection.

The only value that might be set by a management station is deleteTCB (12). Accordingly, it is appropriate for an agent to return a badValue response if a management station attempts to set this object to any other value.

If a management station sets this object to the value delete12 (TCB), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection.

As an implementation-specific option, a RST segment might be sent from the managed node to the other TCP endpoint (note, however, that RST segments are not sent reliably).

Possible values are:

• closed

• listen

• synSent (3)

• synReceived (4)

• established (5)

• finWait1 (6)

• finWait2 (7)

• closeWait (8)

• lastAck (9)

• closing (10)

• timeWait (11)

• deleteTCB (12)

NOTE

Fabric OS v3.1.x and v4.x do not allow the SET operation on this variable.


53-1001156-01

153

2 tcpConnLocalAddress 1.3.6.1.2.1.6.13.1.2

tcpConnLocalAddress 1.3.6.1.2.1.6.13.1.2

The local IP address for this TCP connection. In the case of a connection in the listen state that is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.


53-1001156-01

tcpConnLocalPort 1.3.6.1.2.1.6.13.1.3

The local port number for this TCP connection.

tcpConnLocalPort 1.3.6.1.2.1.6.13.1.3

2


53-1001156-01

155

2 tcpConnRemAddress 1.3.6.1.2.1.6.13.1.4

tcpConnRemAddress 1.3.6.1.2.1.6.13.1.4

The remote IP address for this TCP connection.


53-1001156-01

tcpConnRemPort 1.3.6.1.2.1.6.13.1.5

The remote port number for this TCP connection.

tcpConnRemPort 1.3.6.1.2.1.6.13.1.5

2


53-1001156-01

157

2 tcpInErrs 1.3.6.1.2.1.6.14

tcpInErrs 1.3.6.1.2.1.6.14

The total number of segments received in error (for example, bad TCP checksums).


53-1001156-01

tcpOutRsts 1.3.6.1.2.1.6.15

The number of TCP segments sent containing the RST flag.

tcpOutRsts 1.3.6.1.2.1.6.15

2


53-1001156-01

159

2

UDP Group

UDP Group

Implementation of the UDP group is mandatory for all systems that implement the UDP.


53-1001156-01

udpInDatagrams 1.3.6.1.2.1.7.1

2 udpInDatagrams 1.3.6.1.2.1.7.1

The total number of UDP datagrams delivered to UDP users.


53-1001156-01

161

2 udpNoPorts 1.3.6.1.2.1.7.2

udpNoPorts 1.3.6.1.2.1.7.2

The total number of received UDP datagrams for which there was no application at the destination port.


53-1001156-01

udpInErrors 1.3.6.1.2.1.7.3

2 udpInErrors 1.3.6.1.2.1.7.3

The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.


53-1001156-01

163

2 udpOutDatagrams 1.3.6.1.2.1.7.4

udpOutDatagrams 1.3.6.1.2.1.7.4

The total number of UDP datagrams sent from this entity.


53-1001156-01

udpTable 1.3.6.1.2.1.7.5

udpTable 1.3.6.1.2.1.7.5

The UDP listener table contains information about this entity’s UDP end-points on which a local application is currently accepting datagrams.

2


53-1001156-01

165

2 udpEntry 1.3.6.1.2.1.7.5.1

udpEntry 1.3.6.1.2.1.7.5.1

Index

Information about a particular current UDP listener.

udpLocalAddress, udpLocalPort


53-1001156-01

udpLocalAddress 1.3.6.1.2.1.7.5.1.1

udpLocalAddress 1.3.6.1.2.1.7.5.1.1

The local IP address for this UDP listener. In the case of a UDP listener that is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used.

2


53-1001156-01

167

2 udpLocalPort 1.3.6.1.2.1.7.5.1.2

udpLocalPort 1.3.6.1.2.1.7.5.1.2

The local port number for this UDP listener.

EGP Group

Brocade does not support the EGP Group. This section is not applicable. Refer to the RFC1213 for complete information regarding the EGP Group.

Transmission Group

Brocade does not support the Transmission Group. This section is not applicable. Refer to the

RFC1213 for complete information regarding the Transmission Group.

SNMP Group

Implementation of the SNMP group is mandatory for all systems that support an SNMP protocol entity. Some of the objects defined next are zero-valued in those SNMP implementations that are optimized to support only those functions specific to either a management agent or a management station. All of the objects that follow refer to an SNMP entity, and there might be several SNMP entities residing on a managed node (for example, if the node is acting as a management station).


53-1001156-01

snmpInPkts 1.3.6.1.2.1.11.1

2 snmpInPkts 1.3.6.1.2.1.11.1

The total number of messages delivered to the SNMP entity from the transport service.


53-1001156-01

169

2 snmpOutPkts 1.3.6.1.2.1.11.2

snmpOutPkts 1.3.6.1.2.1.11.2

The total number of SNMP messages that were passed from the SNMP protocol entity to the transport service.


53-1001156-01

snmpInBadVersions 1.3.6.1.2.1.11.3

2 snmpInBadVersions 1.3.6.1.2.1.11.3

The total number of SNMP messages that were delivered to the SNMP protocol entity and were for an unsupported SNMP version.


53-1001156-01

171

2 snmpInBadCommunityNames 1.3.6.1.2.1.11.4

snmpInBadCommunityNames 1.3.6.1.2.1.11.4

The total number of SNMP messages delivered to the SNMP protocol entity that used a SNMP community name not known to said entity.


53-1001156-01

snmpInBadCommunityUses 1.3.6.1.2.1.11.5

2 snmpInBadCommunityUses 1.3.6.1.2.1.11.5

The total number of SNMP messages delivered to the SNMP protocol entity that represented an

SNMP operation that was not allowed by the SNMP community named in the message.


53-1001156-01

173

2 snmpInASNParseErrs 1.3.6.1.2.1.11.6

snmpInASNParseErrs 1.3.6.1.2.1.11.6

The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP messages.

NOTE

1.3.6.1.2.1.11.7 is not supported.


53-1001156-01

snmpInTooBigs 1.3.6.1.2.1.11.8

2 snmpInTooBigs 1.3.6.1.2.1.11.8

The total number of SNMP PDUs that were delivered to the SNMP protocol entity and for which the value of the error-status field is “tooBig.”


53-1001156-01

175

2 snmpInNoSuchNames 1.3.6.1.2.1.11.9

snmpInNoSuchNames 1.3.6.1.2.1.11.9

The total number of SNMP PDUs that were delivered to the SNMP protocol entity and for which the value of the error-status field is “noSuchName.”


53-1001156-01

snmpInBadValues 1.3.6.1.2.1.11.10

2 snmpInBadValues 1.3.6.1.2.1.11.10

The total number of SNMP PDUs that were delivered to the SNMP protocol entity and for which the value of the error-status field is “badValue.”


53-1001156-01

177

2 snmpInReadOnlys 1.3.6.1.2.1.11.11

snmpInReadOnlys 1.3.6.1.2.1.11.11

The total number valid SNMP PDUs that were delivered to the SNMP protocol entity and for which the value of the error-status field is “readOnly.”

It is a protocol error to generate an SNMP PDU that contains the value “readOnly” in the error-status field; as such, this object is provided as a means of detecting incorrect implementations of the SNMP.


53-1001156-01

snmpInGenErrs 1.3.6.1.2.1.11.12

2 snmpInGenErrs 1.3.6.1.2.1.11.12

The total number of SNMP PDUs that were delivered to the SNMP protocol entity and for which the value of the error-status field is “genErr.”


53-1001156-01

179

2 snmpInTotalReqVars 1.3.6.1.2.1.11.13

snmpInTotalReqVars 1.3.6.1.2.1.11.13

The total number of MIB objects that have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs.


53-1001156-01

snmpInTotalSetVars 1.3.6.1.2.1.11.14

2 snmpInTotalSetVars 1.3.6.1.2.1.11.14

The total number of MIB objects that have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs.


53-1001156-01

181

2 snmpInGetRequests 1.3.6.1.2.1.11.15

snmpInGetRequests 1.3.6.1.2.1.11.15

Status Mandatory

The total number of SNMP Get-Request PDUs that have been accepted and processed by the

SNMP protocol entity.


53-1001156-01

snmpInGetNexts 1.3.6.1.2.1.11.16

2 snmpInGetNexts 1.3.6.1.2.1.11.16

The total number of SNMP Get-Next PDUs that have been accepted and processed by the SNMP protocol entity.


53-1001156-01

183

2 snmpInSetRequests 1.3.6.1.2.1.11.17

snmpInSetRequests 1.3.6.1.2.1.11.17

The total number of SNMP Set-Request PDUs that have been accepted and processed by the SNMP protocol entity.


53-1001156-01

snmpInGetResponses 1.3.6.1.2.1.11.18

snmpInGetResponses 1.3.6.1.2.1.11.18

The total number of SNMP Get-Response PDUs that have been accepted and processed by the

SNMP protocol entity.

2


53-1001156-01

185

2 snmpInTraps 1.3.6.1.2.1.11.19

snmpInTraps 1.3.6.1.2.1.11.19

The total number of SNMP Trap PDUs that have been accepted and processed by the SNMP protocol entity.


53-1001156-01

snmpOutTooBigs 1.3.6.1.2.1.11.20

2 snmpOutTooBigs 1.3.6.1.2.1.11.20

The total number of SNMP PDUs that were generated by the SNMP protocol entity and for which the value of the error-status field is too large.


53-1001156-01

187

2 snmpOutNoSuchNames 1.3.6.1.2.1.11.21

snmpOutNoSuchNames 1.3.6.1.2.1.11.21

The total number of SNMP PDUs that were generated by the SNMP protocol entity and for which the value of the error-status field is “noSuchName.”


53-1001156-01

snmpOutBadValues 1.3.6.1.2.1.11.22

2 snmpOutBadValues 1.3.6.1.2.1.11.22

The total number of SNMP PDUs that were generated by the SNMP protocol entity and for which the value of the error-status field is “badValue.”

NOTE

1.3.6.1.2.1.11.23 is not supported.


53-1001156-01

189

2 snmpOutGenErrs 1.3.6.1.2.1.11.24

snmpOutGenErrs 1.3.6.1.2.1.11.24

The total number of SNMP PDUs that were generated by the SNMP protocol entity and for which the value of the error-status field is “genErr.”


53-1001156-01

snmpOutGetRequests 1.3.6.1.2.1.11.25

snmpOutGetRequests 1.3.6.1.2.1.11.25

The total number of SNMP Get-Request PDUs that have been generated by the SNMP protocol entity.

2


53-1001156-01

191

2 snmpOutGetNexts 1.3.6.1.2.1.11.26

snmpOutGetNexts 1.3.6.1.2.1.11.26

The total number of SNMP Get-Next PDUs that have been generated by the SNMP protocol entity.


53-1001156-01

snmpOutSetRequests 1.3.6.1.2.1.11.27

snmpOutSetRequests 1.3.6.1.2.1.11.27

The total number of SNMP Set-Request PDUs that have been generated by the SNMP protocol entity.

2


53-1001156-01

193

2 snmpOutGetResponses 1.3.6.1.2.1.11.28

snmpOutGetResponses 1.3.6.1.2.1.11.28

The total number of SNMP Get-Response PDUs that have been generated by the SNMP protocol entity.


53-1001156-01

snmpOutTraps 1.3.6.1.2.1.11.29

2 snmpOutTraps 1.3.6.1.2.1.11.29

The total number of SNMP Trap PDUs that have been generated by the SNMP protocol entity.


53-1001156-01

195

2 snmpEnableAuthenTraps 1.3.6.1.2.1.11.30

snmpEnableAuthenTraps 1.3.6.1.2.1.11.30

Values

Indicates whether the SNMP agent process is permitted to generate authentication-failure traps.

The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps might be disabled.


• enabled (1)

• disabled (2)

This object is stored in nonvolatile memory so that it remains constant between reinitializations of the switch. This value can be changed with the snmpconfig command.

ifMIB Group

The ifMIB group is implemented in Fabric OS 5.3.0 and higher to support FCIP tunnels. There are entries in the ifXTable for each WAN interface (GbE port), each FC port, and each FCIP tunnel

(transport interface). The ifXtable is used to support 64 bit FC statistics counters.


53-1001156-01

ifXTable 1.3.6.1.2.1.31.1.1

2 ifXTable 1.3.6.1.2.1.31.1.1

A list of interface entries. The number of entries is given by the value of ifNumber. This table contains additional objects for the interface table.


53-1001156-01

197

2 ifXentry 1.3.6.1.2.1.31.1.1.1

ifXentry 1.3.6.1.2.1.31.1.1.1

An entry in the ifXtable containing additional management information applicable to a particular interface.


53-1001156-01

ifName 1.3.6.1.2.1.31.1.1.1.1

2 ifName 1.3.6.1.2.1.31.1.1.1.1

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the devices console. This might be a text name, such as `le0 or a simple port number, such as `1, depending on the interface naming syntax of the device. If several entries in the iftable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied devices local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.


53-1001156-01

199

2 ifInMulticastPkts 1.3.6.1.2.1.31.1.1.1.2

ifInMulticastPkts 1.3.6.1.2.1.31.1.1.1.2

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and

Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

Not supported.


53-1001156-01

ifInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.3

2 ifInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.3

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

Not supported.


53-1001156-01

201

2 ifOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.4

ifOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.4

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent.

For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime

.

Not supported.


53-1001156-01

ifOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.5

2 ifOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.5

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a Broadcast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime

Not supported.


53-1001156-01

203

2 ifHCInOctets 1.3.6.1.2.1.31.1.1.1.6

ifHCInOctets 1.3.6.1.2.1.31.1.1.1.6

The total number of octets received on the interface, including framing characters. This object is a

64-bit version of ifInOctets. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime


53-1001156-01

ifHCInUcastPkts 1.3.6.1.2.1.31.1.1.1.7

2 ifHCInUcastPkts 1.3.6.1.2.1.31.1.1.1.7

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. This object is a 64-bit version of ifInUcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.


53-1001156-01

205

2 ifHCInMulticastPkts 1.3.6.1.2.1.31.1.1.1.8

ifHCInMulticastPkts 1.3.6.1.2.1.31.1.1.1.8

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and

Functional addresses. This object is a 64-bit version of ifInMulticastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

Not supported.


53-1001156-01

ifHCInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.9

2 ifHCInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.9

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. This object is a 64-bit version of ifInBroadcastPkts.

Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime

Not supported.


53-1001156-01

207

2 ifHCOutOctets 1.3.6.1.2.1.31.1.1.1.10

ifHCOutOctets 1.3.6.1.2.1.31.1.1.1.10

The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit version of ifOutOctets. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.


53-1001156-01

ifHCOutUcastPkts 1.3.6.1.2.1.31.1.1.1.11

2 ifHCOutUcastPkts 1.3.6.1.2.1.31.1.1.1.11

.

The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of ifOutUcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.


53-1001156-01

209

2 ifHCOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.12

ifHCOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.12

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent.

For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of ifOutMulticastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime

Not supported.


53-1001156-01

ifHCOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.13

2 ifHCOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.13

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.

This object is a 64-bit version of ifOutBroadcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

Not supported.


53-1001156-01

211

2 ifLinkUpDownTrapEnable 1.3.6.1.2.1.31.1.1.1.14

ifLinkUpDownTrapEnable 1.3.6.1.2.1.31.1.1.1.14

Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled (1) for interfaces which do not operate on any other interface

(as defined in the ifStackTable), and disabled (2) otherwise.


53-1001156-01

ifHigfSpeed 1.3.6.1.2.1.31.1.1.1.15

2 ifHigfSpeed 1.3.6.1.2.1.31.1.1.1.15

An estimate of the current operational speed of the interface in millions of bits per second. A unit of

1000 equals 1,000,000 bps. For 1 Gbps, the value is 1000, for 2 Gbps, the value 2000, etc.


53-1001156-01

213

2 ifPromiscuousMode 1.3.6.1.2.1.31.1.1.1.16

ifPromiscuousMode 1.3.6.1.2.1.31.1.1.1.16

This object has a value of false(2) if this interface only accepts packets/frames that are addressed to this station. This object has a value of true(1) when the station accepts all packets/frames transmitted on the media. The value true(1) is only legal on certain types of media. If legal, setting this object to a value of true(1) may require the interface to be reset before becoming effective. The value of ifPromiscuousMode does not affect the reception of broadcast and multicast packets/frames by the interface.

Hard-coded to false.


53-1001156-01

ifConnectorPresent 1.3.6.1.2.1.31.1.1.1.17

2 ifConnectorPresent 1.3.6.1.2.1.31.1.1.1.17

Set to true when media is connected, otherwise false. For virtual FC ports, it is always false.


53-1001156-01

215

2 ifAlias 1.3.6.1.2.1.31.1.1.1.18

ifAlias 1.3.6.1.2.1.31.1.1.1.18

This object is an alias name for the interface as specified by a network manager, and provides a non-volatile handle for the interface. On the first instantiation of an interface, the value of ifAlias associated with that interface is the zero-length string. As and when a value is written into an instance of ifAlias through a network management set operation, then the agent must retain the supplied value in the ifAlias instance associated with the same interface for as long as that interface remains instantiated, including across all re-initializations/reboots of the network management system, including those which result in a change of the interfaces ifIndex value. An example of the value which a network manager might store in this object for a WAN interface is the

(Telcos) circuit number/identifier of the interface. Some agents may support write-access only for interfaces having particular values of iftype. An agent which supports write access to this object is required to keep the value in non-volatile storage, but it may limit the length of new values depending on how much storage is already occupied by the current values for other interfaces."

Not supported.


53-1001156-01

ifCounterDiscontinuityTime 1.3.6.1.2.1.31.1.1.1.17

2 ifCounterDiscontinuityTime 1.3.6.1.2.1.31.1.1.1.17

The value of sysUpTime on the most recent occasion at which any one or more of this interfaces counters suffered a discontinuity. The relevant counters are the specific instances associated with this interface of any Counter32 or Counter64 object contained in the iftable or ifXTable. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.

Not supported.


53-1001156-01

217

2 ifCounterDiscontinuityTime 1.3.6.1.2.1.31.1.1.1.17


53-1001156-01

FE MIB Objects

Chapter

3

This chapter provides descriptions and other information specific to FE MIB object types and includes the following information:

•

FE MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219

•

FIBRE-CHANNEL-FE-MIB (MIB-II branch) . . . . . . . . . . . . . . . . . . . . . . . . . . . 219

•

FCFABRIC-ELEMENT-MIB (Experimental Branch) . . . . . . . . . . . . . . . . . . . . 340

FE MIB Overview

Brocade supports two versions of the FE MIB:

•

FIBRE-CHANNEL-FE-MIB (RFC2837) in the MIB-II branch.

•

FCFABRIC-ELEMENT-MIB in the experimental branch.

The version of the FE MIB supported depends on the version of the Fabric OS. Table 6 lists which

FE MIB is supported in which Fabric OS version.

TABLE 6

MIB

FE MIBs and supported Fabric OS versions v6.2.0

v6.1.0

v6.0.0

v5.x

FCFABRIC-ELEMENT-MIB (experimental branch)

Yes Yes Yes

No No No

Yes

No v4.x

Yes

No v3.1.x

Yes

No v3.0.x

Yes

Yes v2.6.x

No

Yes

FIBRE-CHANNEL-FE-MIB (MIB-II branch)

This section contains descriptions and other information specific to FIBRE-CHANNEL-FE-MIB (in the

MIB-II branch), including:

•

FIBRE-CHANNEL-FE-MIB Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221

•

Definitions for FIBRE-CHANNEL-FE-MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224

•

fcFeConfig Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226

•

fcFeStatus Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254

•

fcFeError Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282

•

feFcAccounting Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296

•

fcFeCapability Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324

The descriptions of each of the MIB variables in this chapter come directly from the

FIBRE-CHANNEL-FE-MIB itself. The notes that follows the descriptions typically pertain to

Brocade-specific information and are provided by Brocade.


53-1001156-01

219

3

FIBRE-CHANNEL-FE-MIB (MIB-II branch)

NOTE

Brocade does not support the settable “Write” function for any of the Fibre Channel FE MIB objects except fcFxPortPhyAdminStatus.

The object types in FIBRE-CHANNEL-FE-MIB are organized into the following groupings:

•

Configuration

•

Operational

•

Error

•

Accounting

•

Capability


53-1001156-01

FIBRE-CHANNEL-FE-MIB Organization

3


Figures

17 through

21 depict the organization and structure of FIBRE-CHANNEL-FE-MIB.

- iso

- org

- dod

- internet

- mgmt

- mib-2

- fcFeMIB

- fcFeMIBObjects

- fcFeConfig

- fcFeStatus

- fcFeError

- fcFeAccounting

- fcFeCapabilities

- fcFeMIBConformance

- fcFeMIBCompliances

- fcFeMIBGroups

FIGURE 17

fcFeMIB Hierarchy

- fcFeConfig

- fcFeFabricName 1.3.6.1.2.1.75.1.1.1

- fcFeElementName 1.3.6.1.2.1.75.1.1.2

- fcFeModuleCapacity 1.3.6.1.2.1.75.1.1.3

- fcFeModuleTable 1.3.6.1.2.1.75.1.1.4

- fcFeModuleEntry 1.3.6.1.2.1.75.1.1.4.1

- fcFeModuleIndex 1.3.6.1.2.1.75.1.1.4.1.1

- fcFeModuleDescr 1.3.6.1.2.1.75.1.1.4.1.2

- fcFeModuleObjectID 1.3.6.1.2.1.75.1.1.4.1.3

- fcFeModuleOperStatus 1.3.6.1.2.1.75.1.1.4.1.4

- fcFeModuleLastChange 1.3.6.1.2.1.75.1.1.4.1.5

- fcFeModuleFxPortCapacity 1.3.6.1.2.1.75.1.1.4.1.6

- fcFeModuleName 1.3.6.1.2.1.75.1.1.4.1.7

- fcFxPortTable 1.3.6.1.2.1.75.1.1.5

- fcFxPortEntry 1.3.6.1.2.1.75.1.1.5.1

- fcFxPortIndex 1.3.6.1.2.1.75.1.1.5.1.1

- fcFxPortName 1.3.6.1.2.1.75.1.1.5.1.2

- fcFxPortFcphVersionHigh 1.3.6.1.2.1.75.1.1.5.1.3

- fcFxPortFcphVersionLow 1.3.6.1.2.1.75.1.1.5.1.4

- fcFxPortBbCredit 1.3.6.1.2.1.75.1.1.5.1.5

- fcFxPortRxBufSize 1.3.6.1.2.1.75.1.1.5.1.6

- fcFxPortRatov 1.3.6.1.2.1.75.1.1.5.1.7

- fcFxPortEdtov 1.3.6.1.2.1.75.1.1.5.1.8

- fcFxPortCosSupported 1.3.6.1.2.1.75.1.1.5.1.9

- fcFxPortIntermixSupported 1.3.6.1.2.1.75.1.1.5.1.10

- fcFxPortStackedConnMode 1.3.6.1.2.1.75.1.1.5.1.11

- fcFxPortClass2SeqDeliv 1.3.6.1.2.1.75.1.1.5.1.12


- fcFxPortHoldTime 1.3.6.1.2.1.75.1.1.5.1.14


53-1001156-01

221

222

3


FIGURE 18

fcFeConfig Hierarchy

- fcFeStatus

- fcFxPortStatusTable 1.3.6.1.2.1.75.1.2.1

- fcFxPortStatusEntry 1.3.6.1.2.1.75.1.2.1.1

- fcFxPortID 1.3.6.1.2.1.75.1.2.1.1.1

- fcFxPortBbCreditAvailable 1.3.6.1.2.1.75.1.2.1.1.2

- fcFxPortOperMode 1.3.6.1.2.1.75.1.2.1.1.3

- fcFxPortAdminMode 1.3.6.1.2.1.75.1.2.1.1.4

- fcFxPortPhysTable 1.3.6.1.2.1.75.1.2.2

- fcFxPortPhysEntry 1.3.6.1.2.1.75.1.2.2.1

- fcFxPortPhysAdminStatus 1.3.6.1.2.1.75.1.2.2.1.1

- fcFxPortPhysOperStatus 1.3.6.1.2.1.75.1.2.2.1.2

- fcFxPortPhysLastChange 1.3.6.1.2.1.75.1.2.2.1.3

- fcFxPortPhysRttov 1.3.6.1.2.1.75.1.2.2.1.4

- fcFxloginTable 1.3.6.1.2.1.75.1.2.3

- fcFxloginEntry 1.3.6.1.2.1.75.1.2.3.1

- fcFxPortNxLoginIndex 1.3.6.1.2.1.75.1.2.3.1.1

- fcFxPortFcphVersionAgreed 1.3.6.1.2.1.75.1.2.3.1.2

- fcFxPortNxPortBbCredit 1.3.6.1.2.1.75.1.2.3.1.3

- fcFxPortNxPortRxDataFieldSize 1.3.6.1.2.1.75.1.2.3.1.4

- fcFxPortCosSuppAgreed 1.3.6.1.2.1.75.1.2.3.1.5

- fcFxPortIntermixSuppAgreed 1.3.6.1.2.1.75.1.2.3.1.6

- fcFxPortStackedConnModeAgreed 1.3.6.1.2.1.75.1.2.3.1.7

- fcFxPortClass2SeqDelivAgreed 1.3.6.1.2.1.75.1.2.3.1.8


- fcFxPortNxPortName 1.3.6.1.2.1.75.1.2.3.1.10

- fcFxPortConnectedNxPort 1.3.6.1.2.1.75.1.2.3.1.11

- fcFxPortBbCreditModel 1.3.6.1.2.1.75.1.2.3.1.12

FIGURE 19

fcFeStatus Hierarchy

- fcFeError

- fcFxPortErrorTable 1.3.6.1.2.1.75.1.3.1

- fcFxPortErrorEntry 1.3.6.1.2.1.75.1.3.1.1

- fcFxPortLinkFailures 1.3.6.1.2.1.75.1.3.1.1.1

- fcFxPortSyncLosses 1.3.6.1.2.1.75.1.3.1.1.2

- fcFxPortSigLosses 1.3.6.1.2.1.75.1.3.1.1.3

- fcFxPortPrimSeqProtoErrors 1.3.6.1.2.1.75.1.3.1.1.4

- fcFxPortInvalidTxWords 1.3.6.1.2.1.75.1.3.1.1.5

- fcFxPortInvalidCrcs 1.3.6.1.2.1.75.1.3.1.1.6

- fcFxPortDelimiterErrors 1.3.6.1.2.1.75.1.3.1.1.7

- fcFxPortAddressIdErrors 1.3.6.1.2.1.75.1.3.1.1.8

- fcFxPortLinkResetIns 1.3.6.1.2.1.75.1.3.1.1.9

- fcFxPortLinkResetOuts 1.3.6.1.2.1.75.1.3.1.1.10

- fcFxPortOlsIns 1.3.6.1.2.1.75.1.3.1.1.11

- fcFxPortOlsOuts 1.3.6.1.2.1.75.1.3.1.1.12

FIGURE 20

fcFeError Hierarchy


53-1001156-01


53-1001156-01


3

- fcFeAccounting

- fcFxPortC1AccountingTable 1.3.6.1.2.1.75.1.4.1

- fcFxPortC1AccountingEntry 1.3.6.1.2.1.75.1.4.1.1

- fcFxPortC1InFrames 1.3.6.1.2.1.75.1.4.1.1.1

- fcFxPortC1OutFrames 1.3.6.1.2.1.75.1.4.1.1.2

- fcFxPortC1InOctets 1.3.6.1.2.1.75.1.4.1.1.3

- fcFxPortC1OutOctets 1.3.6.1.2.1.75.1.4.1.1.4

- fcFxPortC1Discards 1.3.6.1.2.1.75.1.4.1.1.5

- fcFxPortC1FbsyFrames 1.3.6.1.2.1.75.1.4.1.1.6

- fcFxPortC1FrjtFrames 1.3.6.1.2.1.75.1.4.1.1.7

- fcFxPortC1InConnections 1.3.6.1.2.1.75.1.4.1.1.8

- fcFxPortC1OutConnections 1.3.6.1.2.1.75.1.4.1.1.9

- fcFxPortC1ConnTime 1.3.6.1.2.1.75.1.4.1.1.10








- fcFxPortC2FbsyFrames 1.3.6.1.2.1.75.1.4.2.1.6

- fcFxPortC2FrjtFrames 1.3.6.1.2.1.75.1.4.2.1.7








FIGURE 21

fcFeAccounting Hierarchy

- fcFeCabilities

- fcFxPortCapTable 1.3.6.1.2.1.75.1.5.1

- fcFxPortCapEntry 1.3.6.1.2.1.75.1.5.1.1

- fcFxPortCapFcphVersionHigh 1.3.6.1.2.1.75.1.5.1.1.1

- fcFxPortCapFcphVersionLow 1.3.6.1.2.1.75.1.5.1.1.2

- fcFxPortCapBbCreditMax 1.3.6.1.2.1.75.1.5.1.1.3

- fcFxPortCapBbCreditMin 1.3.6.1.2.1.75.1.5.1.1.4

- fcFxPortCapRxDataFieldSizeMax 1.3.6.1.2.1.75.1.5.1.1.5

- fcFxPortCapRxDataFieldSizeMin 1.3.6.1.2.1.75.1.5.1.1.6

- fcFxPortCapCos 1.3.6.1.2.1.75.1.5.1.1.7

- fcFxPortCapIntermix 1.3.6.1.2.1.75.1.5.1.1.8

- fcFxPortCapStackedConnMode 1.3.6.1.2.1.75.1.5.1.1.9

- fcFxPortCapClass2SeqDeliv 1.3.6.1.2.1.75.1.5.1.1.10


- fcFxPortCapHoldTimeMax 1.3.6.1.2.1.75.1.5.1.1.12

- fcFxPortCapHoldTimeMin 1.3.6.1.2.1.75.1.5.1.1.13

FIGURE 22

fcFeCabilities Hierarchy

223

3

Definitions for FIBRE-CHANNEL-FE-MIB


Table 7

lists the definitions for fcFeMIB.

TABLE 7

Type Definition

Display string

FIBRE-CHANNEL-FE-MIB Definitions

Value

Octet string of size 0 to 255

Milliseconds

Microseconds

FcNameId

FabricName

FcPortName

FcAddressId

FcRxDataFieldSize

FcBbCredit

FcphVersion

FcStackedConnMode

FcCosCap

Integer from 0 to 2147383647


Octet string of size 8







Integer from 1 to 3


Description

Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854.

Represents time unit value in milliseconds.

Represents time unit value in microseconds.

World Wide Name or Fibre Channel name associated with an

FC entity. It is a Network_Destination_ID or Network_Source_ID composed of a value up to 60 bits wide, occupying the remaining 8 bytes while the first nibble identifies the format of the Name_Identifier.

Name_Identifier hex values:

0 (ignored)

1 (IEEE 48-bit address)

2 (IEEE extended)

3 (locally assigned)

4 (32-bit IP address)

The name identifier of a fabric. Each fabric provides a unique fabric name.

Valid formats include:

IEEE 48

Local

The name identifier associated with a port.

Valid formats include:

IEEE 48

IEEE extended

Local

A 24-bit value unique within the address space of a fabric.

Receive data field size of an Nx_Port or Fx_Port.

Buffer-to-buffer credit of an Nx_Port or Fx_Port.

Version of FC-PH supported by an Nx_Port or Fx_Port.

Indicates the Class 1 Stacked Connect Mode supported by an

Nx_Port or Fx_Port.

1 (none)

2 (transparent)

3 (lockedDown)

Class of service capability of an Nx_Port or Fx_Port.

bit 0 (Class F) bit 1 (Class 1) bit 2 (Class 2) bit 3 (Class 3) bit 4 (Class 4) bit 5 (Class 5) bit 6 (Class 6) bit 7 (reserved for future)


53-1001156-01


3

TABLE 7

Type Definition

Fc0BaudRate

FIBRE-CHANNEL-FE-MIB Definitions (Continued)

Value

Integer according to FC-0 baud rates

Fc0BaudRateCap

Fc0MediaCap

Fc0Medium

Fc0TxType

Fc0Distance

FcFeModuleCapacity



Integer

Integer

Integer


Description

1 (other) None of below

2 (one-eighth) 155 Mbaud (12.5 MB/s)

4 (quarter) 266 Mbaud (25.0 MB/s)

8 (half) 532 Mbaud (50.0 MB/s)

16 (full) 1 Gbaud (100 MB/s)

32 (double) 2 Gbaud (200 MB/s)

64 (quadruple) 4 Gbaud (400 MB/s) bit 0 (other) bit 1 (one-eighth) bit 2 (quarter) bit 3 (half) bit 4 (full) bit 5 (double) bit 6 (quadruple) bit 7 (Reserved for future) bit 0 (unknown) bit 1 (single mode fibre (sm)) bit 2 (multimode fibre 50 micron (m5)) bit 3 (multimode fibre 62.5 micron (m6)) bit 4 (video cable (tv)) bit 5 (miniature cable (mi)) bit 6 (shielded twisted pair (stp)) bit 7 (twisted wire (tw)) bit 8 (long video (lv)) bits 9-15 (Reserved for future use)

1 (unknown)

2 (sm)

4 (m5)

8 (m6)

16 (tv)

32 (mi)

64 (stp)

128 (tw)

256 (lv)

1 (unknown)

2 (longWaveLaser (LL))

3 (shortWaveLaser (SL))

4 (longWaveLED (LE))

5 (electrical (EL))

6 (shortWaveLaser-noOFC (SN))

The FC-0 distance range associated with a port transmitter:

1 (unknown)

2 (long)

3 (intermediate)

4 (short)

Maximum number of modules within a fabric element; returns

1 for all devices.


53-1001156-01

225

3 fcFeConfig Group

TABLE 7

FIBRE-CHANNEL-FE-MIB Definitions (Continued)

Type Definition

FcFeFxPortCapacity

Value


FcFeModuleIndex

FcFeFxPortIndex

FcFeNxPortIndex

FcFxPortMode

FcBbCreditModel




Integer

Integer

Description

Maximum number of Fx_Ports within a module.

For the Brocade 3250, this value is 8.


For the Brocade 200E and 3850, this value is 16.

For the Brocade 3900 and 4100, this value is 32.


For the Brocade 5000, this value is 32




For the Brocade DCX, this value is 384.




For the Brocade Encryption switch, this value is 32.

For the Brocade DCX-4S, this value is 192.

Module index within a conceptual table.

Fx_Port index within a conceptual table.

Nx_Port index within a conceptual table.

1 (unknown)

2 (F_Port)

3 (FL_Port)

BB_Credit model of an Fx_Port.

1 (regular)

2 (alternate)

fcFeConfig Group

This group consists of scalar objects and tables. It contains the configuration and service parameters of the fabric element and the Fx_Ports.

The group represents a set of parameters associated with the fabric element or an Fx_Port to support its Nx_Ports.


53-1001156-01

fcFeFabricName 1.3.6.1.2.1.75.1.1.1

3 fcFeFabricName 1.3.6.1.2.1.75.1.1.1

Returns

The Name_Identifier of the Fabric to which this Fabric Element belongs.

Displays the WWN of the primary switch in the fabric.


53-1001156-01

227

3 fcFeElementName 1.3.6.1.2.1.75.1.1.2

fcFeElementName 1.3.6.1.2.1.75.1.1.2

Returns

The Name_Identifier of the fabric element.

Displays the WWN of the switch.


53-1001156-01

fcFeModuleCapacity 1.3.6.1.2.1.75.1.1.3

3 fcFeModuleCapacity 1.3.6.1.2.1.75.1.1.3

Value

The maximum number of modules in the fabric element, regardless of their current state.

The valid value for all Brocade switches is 1.


53-1001156-01

229

3 fcFeModuleTable 1.3.6.1.2.1.75.1.1.4

fcFeModuleTable 1.3.6.1.2.1.75.1.1.4

A table that contains information about the modules, one entry for each module in the fabric element.


53-1001156-01

fcFeModuleEntry 1.3.6.1.2.1.75.1.1.4.1

3 fcFeModuleEntry 1.3.6.1.2.1.75.1.1.4.1

Index

An entry containing the configuration parameters of a module.

1: fcFeModuleIndex


53-1001156-01

231

3 fcFeModuleIndex 1.3.6.1.2.1.75.1.1.4.1.1

fcFeModuleIndex 1.3.6.1.2.1.75.1.1.4.1.1

Identifies the module within the fabric element for which this entry contains information. This value is never greater than fcFeModuleCapacity. This entry never shows any value as it is shown as non accessible in the browser.


53-1001156-01

fcFeModuleDescr 1.3.6.1.2.1.75.1.1.4.1.2

3 fcFeModuleDescr 1.3.6.1.2.1.75.1.1.4.1.2

A textual description of the module. This value should include the full name and version identification of the module. It should contain printable ASCII characters.

Refer to “sysDescr 1.3.6.1.2.1.1.1” on page 22.


53-1001156-01

233

3 fcFeModuleObjectID 1.3.6.1.2.1.75.1.1.4.1.3

fcFeModuleObjectID 1.3.6.1.2.1.75.1.1.4.1.3

The vendor’s authoritative identification of the module. This value might be allocated within the

SMI enterprises subtree (1.3.6.1.4.1) and provides a straightforward and unambiguous means for determining what kind of module is being managed.

For example, this object could take the value 1.3.6.1.4.1.99649.3.9 if vendor “Neufe Inc.” was assigned the subtree 1.3.6.1.4.1.99649 and had assigned the identifier 1.3.6.1.4.1.99649.3.9 to its “FeFiFo-16 PlugInCard.”

Refer to “sysObjectID 1.3.6.1.2.1.1.2” on page 23.


53-1001156-01

fcFeModuleOperStatus 1.3.6.1.2.1.75.1.1.4.1.4

3 fcFeModuleOperStatus 1.3.6.1.2.1.75.1.1.4.1.4

Values

Indicates the operational status of the module.

1 - online, module functioning properly

2 - offline, module not available

3 - testing, module in test mode

4 - faulty, module is defective


53-1001156-01

235

3 fcFeModuleLastChange 1.3.6.1.2.1.75.1.1.4.1.5

fcFeModuleLastChange 1.3.6.1.2.1.75.1.1.4.1.5

Contains the value of sysUpTime when the module entered its current operational status. A value of 0 indicates that the operational status of the module has not changed since the agent last restarted.


53-1001156-01

fcFeModuleFxPortCapacity 1.3.6.1.2.1.75.1.1.4.1.6

3 fcFeModuleFxPortCapacity 1.3.6.1.2.1.75.1.1.4.1.6

Values

The number of Fx_Ports that can be contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to fcFeModuleFxPortCapacity, inclusive. However, the numbers are not required to be contiguous.

Valid values are:

Brocade 3200, 3250

Brocade 4012

Brocade 200E, 3800, 3850

Brocade 3900, 4100

Brocade 4900,

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000 / 24000

Brocade 48000

Brocade DCX

Brocade DCX-4S

Brocade Encryption Switch

8 ports

12 ports

16 ports

32 ports

50 ports

32 ports

16 ports

16 ports

128 ports

448 ports

384 ports

192 ports

32 ports


53-1001156-01

237

3 fcFeModuleName 1.3.6.1.2.1.75.1.1.4.1.7

fcFeModuleName 1.3.6.1.2.1.75.1.1.4.1.7

Return

The Name_Identifier of the module.

Displays the WWN of the switch.


53-1001156-01

fcFxPortTable 1.3.6.1.2.1.75.1.1.5

fcFxPortTable 1.3.6.1.2.1.75.1.1.5

A table that contains configuration and service parameters of the Fx_Ports, one entry for each

Fx_Port in the fabric element.

3


53-1001156-01

239

3 fcFxPortEntry 1.3.6.1.2.1.75.1.1.5.1

fcFxPortEntry 1.3.6.1.2.1.75.1.1.5.1

Index

An entry containing the configuration and service parameters of an Fx_Port.

1: fcFeModuleIndex

2: fcFxPortIndex


53-1001156-01

fcFxPortIndex 1.3.6.1.2.1.75.1.1.5.1.1

3 fcFxPortIndex 1.3.6.1.2.1.75.1.1.5.1.1

Identifies the Fx_Port within the module. This number ranges from 1 to the value of fcFeModulePortCapacity for the associated module. The value remains constant for the identified

Fx_Port until the module is reinitialized.


53-1001156-01

241

3 fcFxPortName 1.3.6.1.2.1.75.1.1.5.1.2

fcFxPortName 1.3.6.1.2.1.75.1.1.5.1.2

Return

The World Wide Name of this Fx_Port. Each Fx_Port has a unique port World Wide Name within the fabric.

Displays the WWN of the port.


53-1001156-01

fcFxPortFcphVersionHigh 1.3.6.1.2.1.75.1.1.5.1.3

3 fcFxPortFcphVersionHigh 1.3.6.1.2.1.75.1.1.5.1.3

The highest or most recent version of FC-PH that the Fx_Port is configured to support. This value is always 32.


53-1001156-01

243

3 fcFxPortFcphVersionLow 1.3.6.1.2.1.75.1.1.5.1.4

fcFxPortFcphVersionLow 1.3.6.1.2.1.75.1.1.5.1.4

The lowest or earliest version of FC-PH that the Fx_Port is configured to support. This value is always 6,


53-1001156-01

fcFxPortBbCredit 1.3.6.1.2.1.75.1.1.5.1.5

3 fcFxPortBbCredit 1.3.6.1.2.1.75.1.1.5.1.5

The total number of receive buffers available for holding Class 1 connect-request, and Class 2 or 3 frames from the attached Nx_Port. It is for buffer-to-buffer flow control in the direction from the attached Nx_Port (if applicable) to Fx_Port.


53-1001156-01

245

3 fcFxPortRxBufSize 1.3.6.1.2.1.75.1.1.5.1.6

fcFxPortRxBufSize 1.3.6.1.2.1.75.1.1.5.1.6

The largest Data_Field Size (in octets) for an FT_1 frame that can be received by the Fx_Port.


53-1001156-01

fcFxPortRatov 1.3.6.1.2.1.75.1.1.5.1.7

3 fcFxPortRatov 1.3.6.1.2.1.75.1.1.5.1.7

The Resource_Allocation_Timeout value configured for the Fx_Port. This is used as the time-out value for determining when to reuse an Nx_Port resource such as a Recovery_Qualifier. It represents E_D_TOV (Refer to

“fcFxPortEdtov 1.3.6.1.2.1.75.1.1.5.1.8” on page 248) plus twice the

maximum time that a frame might be delayed within the fabric and still be delivered.


53-1001156-01

247

3 fcFxPortEdtov 1.3.6.1.2.1.75.1.1.5.1.8

fcFxPortEdtov 1.3.6.1.2.1.75.1.1.5.1.8

The E_D_TOV value configured for the Fx_Port. The Error_Detect_Timeout value is used as the time-out value for detecting an error condition.


53-1001156-01

fcFxPortCosSupported 1.3.6.1.2.1.75.1.1.5.1.9

3 fcFxPortCosSupported 1.3.6.1.2.1.75.1.1.5.1.9

A value indicating the set of Classes of Service supported by the Fx_Port.


53-1001156-01

249

3 fcFxPortIntermixSupported 1.3.6.1.2.1.75.1.1.5.1.10

fcFxPortIntermixSupported 1.3.6.1.2.1.75.1.1.5.1.10

A flag indicating whether the Fx_Port supports an Intermixed Dedicated Connection.

1 - true

2- false


53-1001156-01

fcFxPortStackedConnMode 1.3.6.1.2.1.75.1.1.5.1.11

3 fcFxPortStackedConnMode 1.3.6.1.2.1.75.1.1.5.1.11

A value indicating the mode of Stacked Connect supported by the Fx_Port.

1 - none

2 - transparent

3 - locked down


53-1001156-01

251

3 fcFxPortClass2SeqDeliv 1.3.6.1.2.1.75.1.1.5.1.12

fcFxPortClass2SeqDeliv 1.3.6.1.2.1.75.1.1.5.1.12

A flag indicating whether Class 2 Sequential Delivery is supported by the Fx_Port.

1 - true

2- false


53-1001156-01



A flag indicating whether Class 3 Sequential Delivery is supported by the Fx_Port.

1 - true

2- false


53-1001156-01

253

3 fcFxPortHoldTime 1.3.6.1.2.1.75.1.1.5.1.14

fcFxPortHoldTime 1.3.6.1.2.1.75.1.1.5.1.14

The maximum time (in microseconds) that the Fx_Port holds a frame before discarding the frame if it is unable to deliver the frame. The value 0 means that the Fx_Port does not support this parameter.

fcFeStatus Group

This group consists of tables that contain operational status and established service parameters for the fabric element and the attached Nx_Ports.


53-1001156-01

fcFxPortStatusTable 1.3.6.1.2.1.75.1.2.1

3 fcFxPortStatusTable 1.3.6.1.2.1.75.1.2.1

A table that contains operational status and parameters of the Fx_Ports, one entry for each Fx_Port in the fabric element.


53-1001156-01

255

3 fcFxPortStatusEntry 1.3.6.1.2.1.75.1.2.1.1

fcFxPortStatusEntry 1.3.6.1.2.1.75.1.2.1.1

Augments

An entry containing operational status and parameters of an Fx_Port.

1: fcFxPortEntry


53-1001156-01

fcFxPortID 1.3.6.1.2.1.75.1.2.1.1.1

3 fcFxPortID 1.3.6.1.2.1.75.1.2.1.1.1

The address identifier by which this Fx_Port is identified within the fabric. The Fx_Port might assign its address identifier to its attached Nx_Port(s) during fabric login.


53-1001156-01

257

3 fcFxPortBbCreditAvailable 1.3.6.1.2.1.75.1.2.1.1.2

fcFxPortBbCreditAvailable 1.3.6.1.2.1.75.1.2.1.1.2

The number of buffers currently available for receiving frames from the attached port in the buffer-to-buffer flow control. The value should be less than or equal to fcFxPortBbCredit.


53-1001156-01

fcFxPortOperMode 1.3.6.1.2.1.75.1.2.1.1.3

3 fcFxPortOperMode 1.3.6.1.2.1.75.1.2.1.1.3

Values

The current operational mode of the Fx_Port.


1: unknown(1)

2: fPort(2)

3: flPort(3)


53-1001156-01

259

3 fcFxPortAdminMode 1.3.6.1.2.1.75.1.2.1.1.4

fcFxPortAdminMode 1.3.6.1.2.1.75.1.2.1.1.4

The desired operational mode of the Fx_Port.


53-1001156-01

Fx_Port Physical Level Table

Fx_Port Physical Level Table

This table contains the physical level status and parameters of the Fx_Ports, one entry for each


3


53-1001156-01

261

3 fcFxPortPhysTable 1.3.6.1.2.1.75.1.2.2

fcFxPortPhysTable 1.3.6.1.2.1.75.1.2.2

A table that contains the physical level status and parameters of the Fx_Ports, one entry for each



53-1001156-01

fcFxPortPhysEntry 1.3.6.1.2.1.75.1.2.2.1

3 fcFxPortPhysEntry 1.3.6.1.2.1.75.1.2.2.1

An entry containing physical level status and parameters of an Fx_Port.


53-1001156-01

263

3 fcFxPortPhysAdminStatus 1.3.6.1.2.1.75.1.2.2.1.1

fcFxPortPhysAdminStatus 1.3.6.1.2.1.75.1.2.2.1.1

Values

The desired state of the Fx_Port. A management station might place the Fx_Port in a desired state by setting this object accordingly.


1: online(1)

2: offline(2)

3: testing(3)

The testing state (3) indicates that no operational frames can be passed. When a fabric element initializes, all Fx_Ports start with fcFxPortPhysAdminStatus in the offline state (2). As the result of either explicit management action or per configuration information accessible by the fabric element, fcFxPortPhysAdminStatus is then changed to either the online (1) or testing (3) states or remains in the offline state (2).


53-1001156-01

fcFxPortPhysOperStatus 1.3.6.1.2.1.75.1.2.2.1.2

3 fcFxPortPhysOperStatus 1.3.6.1.2.1.75.1.2.2.1.2

Values

The current operational status of the Fx_Port.


1: online(1)

2: offline(2)

3: testing(3)

4: linkFailure(4)

The testing state (3) indicates that no operational frames can be passed. If fcFxPortPhysAdminStatus is offline (2), then fcFxPortPhysOperStatus should be offline (2). If fcFxPortPhysAdminStatus is changed to online (1), then fcFxPortPhysOperStatus should change to online (1) if the Fx_Port is ready to accept fabric login request from the attached Nx_Port; it should proceed and remain in the linkFailure (4) state only if there is a fault that prevents it from going to the online state (1).


53-1001156-01

265

3 fcFxPortPhysLastChange 1.3.6.1.2.1.75.1.2.2.1.3

fcFxPortPhysLastChange 1.3.6.1.2.1.75.1.2.2.1.3

The value of sysUpTime at the time the Fx_Port entered its current operational status. A value of 0 indicates that the Fx_Port operational status has not changed since the agent last restarted.


53-1001156-01

fcFxPortPhysRttov 1.3.6.1.2.1.75.1.2.2.1.4

3 fcFxPortPhysRttov 1.3.6.1.2.1.75.1.2.2.1.4

The Receiver_Transmitter_Timeout value of the Fx_Port. This is used by the receiver logic to detect loss of synchronization. This value is displayed in milliseconds.

NOTE

This object is read-only. It is listed incorrectly in the MIB definition as read-write.


53-1001156-01

267

3

Fx_Port Fabric Login Table


This table contains one entry for each Fx_Port in the fabric element and the service parameters that have been established from the most recent fabric login, whether implicit or explicit.


53-1001156-01

fcFxloginTable 1.3.6.1.2.1.75.1.2.3

3 fcFxloginTable 1.3.6.1.2.1.75.1.2.3

A table that contains services parameters established from the most recent fabric login, explicit or implicit, one entry for each Fx_Port in the fabric element.


53-1001156-01

269

3 fcFxloginEntry 1.3.6.1.2.1.75.1.2.3.1

fcFxloginEntry 1.3.6.1.2.1.75.1.2.3.1

Indexes

An entry containing service parameters established from a successful fabric login.

1: fcFeModuleIndex

2: fcFxPortIndex

3: fcFxPortNxLoginIndex


53-1001156-01

fcFxPortNxLoginIndex 1.3.6.1.2.1.75.1.2.3.1.1

3 fcFxPortNxLoginIndex 1.3.6.1.2.1.75.1.2.3.1.1

The associated Nx_Port in the attachment for which the entry contains information.


53-1001156-01

271

3 fcFxPortFcphVersionAgreed 1.3.6.1.2.1.75.1.2.3.1.2

fcFxPortFcphVersionAgreed 1.3.6.1.2.1.75.1.2.3.1.2

The version of FC-PH that the Fx_Port has agreed to support from the fabric login.


53-1001156-01

fcFxPortNxPortBbCredit 1.3.6.1.2.1.75.1.2.3.1.3

3 fcFxPortNxPortBbCredit 1.3.6.1.2.1.75.1.2.3.1.3

The total number of buffers available for holding Class 1 connect-request, and Class 2 or Class 3 frames to be transmitted to the attached Nx_Port. It is for buffer-to-buffer flow control in the direction from Fx_Port to Nx_Port. The buffer-to-buffer flow control mechanism is indicated in the respective fcFxPortBbCreditModel.


53-1001156-01

273

3 fcFxPortNxPortRxDataFieldSize 1.3.6.1.2.1.75.1.2.3.1.4

fcFxPortNxPortRxDataFieldSize 1.3.6.1.2.1.75.1.2.3.1.4

The Receive Data Field Size of the attached Nx_Port. This is a binary value that specifies the largest

Data Field Size for an FT_1 frame that can be received by the Nx_Port. The value is a number of bytes in the range 128 to 2112, inclusive.


53-1001156-01

fcFxPortCosSuppAgreed 1.3.6.1.2.1.75.1.2.3.1.5

3 fcFxPortCosSuppAgreed 1.3.6.1.2.1.75.1.2.3.1.5

Indicates that the attached Nx_Port has requested the Fx_Port for the support of classes of services and the Fx_Port has granted the request.


53-1001156-01

275

3 fcFxPortIntermixSuppAgreed 1.3.6.1.2.1.75.1.2.3.1.6

fcFxPortIntermixSuppAgreed 1.3.6.1.2.1.75.1.2.3.1.6

A variable indicating that the attached Nx_Port has requested the Fx_Port for Intermix support, and the Fx_Port has granted the request. This flag is only valid if Class 1 service is supported.


53-1001156-01

fcFxPortStackedConnModeAgreed 1.3.6.1.2.1.75.1.2.3.1.7

3 fcFxPortStackedConnModeAgreed 1.3.6.1.2.1.75.1.2.3.1.7

Indicates whether the Fx_Port has agreed to support stacked connect from the fabric login. This is only meaningful if Class 1 service has been agreed to.


53-1001156-01

277

3 fcFxPortClass2SeqDelivAgreed 1.3.6.1.2.1.75.1.2.3.1.8

fcFxPortClass2SeqDelivAgreed 1.3.6.1.2.1.75.1.2.3.1.8

Values

Indicates whether the Fx_Port has agreed to support Class 2 sequential delivery from the fabric login. This is only meaningful if Class 2 service has been agreed to.


• yes (1) The Fx_Port has agreed to support Class 2 sequential delivery from the fabric login.

• no (2) The Fx_Port has not agreed to support Class 2 sequential delivery from the fabric login.


53-1001156-01



Values

A flag indicating whether the Fx_Port has agreed to support Class 3 sequential delivery from the fabric login. This is only meaningful if Class 3 service has been agreed to.


• yes (1) The Fx_Port has agreed to support Class 3 sequential delivery from the fabric login.

• no (2) The Fx_Port has not agreed to support Class 3 sequential delivery from the fabric login.


53-1001156-01

279

3 fcFxPortNxPortName 1.3.6.1.2.1.75.1.2.3.1.10

fcFxPortNxPortName 1.3.6.1.2.1.75.1.2.3.1.10

The port name of the attached Nx_Port, if applicable. If the value of this object is

‘0000000000000000’H, this Fx_Port has no Nx_Port attached to it.

If the Fx_Port has no attached Nx_Port then the instance of the port is not displayed.


53-1001156-01

fcFxPortConnectedNxPort 1.3.6.1.2.1.75.1.2.3.1.11


The address identifier of the destination Fx_Port with which this Fx_Port is currently engaged in either a Class 1 or loop connection. If the value of this object is ‘000000’H, this Fx_Port is not engaged in a connection.

If the Fx_Port has no attached Nx_Port then the instance of the port is not displayed.

3


53-1001156-01

281

3 fcFxPortBbCreditModel 1.3.6.1.2.1.75.1.2.3.1.12

fcFxPortBbCreditModel 1.3.6.1.2.1.75.1.2.3.1.12

Identifies the BB_Credit model used by the Fx_Port. The regular model refers to the buffer-to-buffer flow control mechanism defined in FC-PH [1] used between the F_Port and the N_Port. For

FL_Ports, the alternate buffer-to-buffer flow control mechanism as defined in FC-AL [4] is used between the FL_Port and any attached NL_Ports.

fcFeError Group

This group consists of tables that contain information about the various types of errors detected.

The management station might use the information in this group to determine the quality of the link between the Fx_Port and its attached Nx_Port.

Implementation of this group is optional.


53-1001156-01

fcFxPortErrorTable 1.3.6.1.2.1.75.1.3.1

3 fcFxPortErrorTable 1.3.6.1.2.1.75.1.3.1

A table that contains counters that record the numbers of errors detected, one entry for each

Fx_Port.

This table contains counters recording numbers of errors detected since the management agent reinitialized, one entry for each Fx_Port in the fabric element.

The first six columnar objects after the port index correspond to the counters in the link error status block.


53-1001156-01

283

3 fcFxPortErrorEntry 1.3.6.1.2.1.75.1.3.1.1

fcFxPortErrorEntry 1.3.6.1.2.1.75.1.3.1.1

Augments

An entry containing error counters of a Fx_Port.

1: fcFxPortEntry


53-1001156-01

fcFxPortLinkFailures 1.3.6.1.2.1.75.1.3.1.1.1

3 fcFxPortLinkFailures 1.3.6.1.2.1.75.1.3.1.1.1

The number of link failures detected by this Fx_Port.


53-1001156-01

285

3 fcFxPortSyncLosses 1.3.6.1.2.1.75.1.3.1.1.2

fcFxPortSyncLosses 1.3.6.1.2.1.75.1.3.1.1.2

The number of loss of synchronization errors detected by the Fx_Port.


53-1001156-01

fcFxPortSigLosses 1.3.6.1.2.1.75.1.3.1.1.3

3 fcFxPortSigLosses 1.3.6.1.2.1.75.1.3.1.1.3

The number of loss of signal errors detected by the Fx_Port.


53-1001156-01

287

3 fcFxPortPrimSeqProtoErrors 1.3.6.1.2.1.75.1.3.1.1.4

fcFxPortPrimSeqProtoErrors 1.3.6.1.2.1.75.1.3.1.1.4

The number of primitive sequence protocol errors detected by the Fx_Port.


53-1001156-01

fcFxPortInvalidTxWords 1.3.6.1.2.1.75.1.3.1.1.5

3 fcFxPortInvalidTxWords 1.3.6.1.2.1.75.1.3.1.1.5

The number of invalid transmission word errors detected by the Fx_Port.


53-1001156-01

289

3 fcFxPortInvalidCrcs 1.3.6.1.2.1.75.1.3.1.1.6

fcFxPortInvalidCrcs 1.3.6.1.2.1.75.1.3.1.1.6

The number of invalid cyclic redundancy checks (CRC) detected by this Fx_Port.


53-1001156-01

fcFxPortDelimiterErrors 1.3.6.1.2.1.75.1.3.1.1.7

3 fcFxPortDelimiterErrors 1.3.6.1.2.1.75.1.3.1.1.7

The number of delimiter errors detected by this Fx_Port.


53-1001156-01

291

3 fcFxPortAddressIdErrors 1.3.6.1.2.1.75.1.3.1.1.8

fcFxPortAddressIdErrors 1.3.6.1.2.1.75.1.3.1.1.8

The number of address identifier errors detected by this Fx_Port.


53-1001156-01

fcFxPortLinkResetIns 1.3.6.1.2.1.75.1.3.1.1.9

3 fcFxPortLinkResetIns 1.3.6.1.2.1.75.1.3.1.1.9

The number of Link Reset Protocol errors received by this Fx_Port from the attached Nx_Port.


53-1001156-01

293

3 fcFxPortLinkResetOuts 1.3.6.1.2.1.75.1.3.1.1.10

fcFxPortLinkResetOuts 1.3.6.1.2.1.75.1.3.1.1.10

The number of Link Reset Protocol errors issued by this Fx_Port to the attached Nx_Port.


53-1001156-01

fcFxPortOlsIns 1.3.6.1.2.1.75.1.3.1.1.11

3 fcFxPortOlsIns 1.3.6.1.2.1.75.1.3.1.1.11

The number of Offline Sequence errors received by this Fx_Port.


53-1001156-01

295

3 fcFxPortOlsOuts 1.3.6.1.2.1.75.1.3.1.1.12

fcFxPortOlsOuts 1.3.6.1.2.1.75.1.3.1.1.12

The number of Offline Sequence issued by this Fx_Port.

feFcAccounting Group

The Accounting group is supported only in Fabric OS v4.x.

The Accounting group consists of the following tables:

•

Class 1 accounting table

•


•


Each table contains accounting information for the Fx_Ports in the fabric element.


53-1001156-01

fcFxPortC1AccountingTable 1.3.6.1.2.1.75.1.4.1

3 fcFxPortC1AccountingTable 1.3.6.1.2.1.75.1.4.1

A table that contains Class 1 accounting information recorded since the management agent reinitialized, one entry for each Fx_Port in the fabric element.


53-1001156-01

297

3 fcFxPortC1AccountingEntry 1.3.6.1.2.1.75.1.4.1.1

fcFxPortC1AccountingEntry 1.3.6.1.2.1.75.1.4.1.1

Augments:

An entry containing Class 1 accounting information for each Fx_Port.

1: fcFxPortEntry


53-1001156-01

fcFxPortC1InFrames 1.3.6.1.2.1.75.1.4.1.1.1

3 fcFxPortC1InFrames 1.3.6.1.2.1.75.1.4.1.1.1

The number of Class 1 frames (other than Class 1 connect-request) received by this Fx_Port from its attached Nx_Port.


53-1001156-01

299

3 fcFxPortC1OutFrames 1.3.6.1.2.1.75.1.4.1.1.2

fcFxPortC1OutFrames 1.3.6.1.2.1.75.1.4.1.1.2

The number of Class 1 frames (other than Class 1 connect-request) delivered through this Fx_Port to its attached Nx_Port.


53-1001156-01

fcFxPortC1InOctets 1.3.6.1.2.1.75.1.4.1.1.3

3 fcFxPortC1InOctets 1.3.6.1.2.1.75.1.4.1.1.3

The number of Class 1 frame octets, including the frame delimiters, received by this Fx_Port from its attached Nx_Port.


53-1001156-01

301

3 fcFxPortC1OutOctets 1.3.6.1.2.1.75.1.4.1.1.4

fcFxPortC1OutOctets 1.3.6.1.2.1.75.1.4.1.1.4

The number of Class 1 frame octets, including the frame delimiters, delivered through this Fx_Port its attached Nx_Port.


53-1001156-01

fcFxPortC1Discards 1.3.6.1.2.1.75.1.4.1.1.5

3 fcFxPortC1Discards 1.3.6.1.2.1.75.1.4.1.1.5

The number of Class 1 frames discarded by this Fx_Port.


53-1001156-01

303

3 fcFxPortC1FbsyFrames 1.3.6.1.2.1.75.1.4.1.1.6

fcFxPortC1FbsyFrames 1.3.6.1.2.1.75.1.4.1.1.6

The number of F_BSY frames generated by this Fx_Port against Class 1 connect-request.


53-1001156-01

fcFxPortC1FrjtFrames 1.3.6.1.2.1.75.1.4.1.1.7

3 fcFxPortC1FrjtFrames 1.3.6.1.2.1.75.1.4.1.1.7

The number of F_RJT frames generated by this Fx_Port against Class 1 connect-request.


53-1001156-01

305

3 fcFxPortC1InConnections 1.3.6.1.2.1.75.1.4.1.1.8

fcFxPortC1InConnections 1.3.6.1.2.1.75.1.4.1.1.8

The number of Class 1 connections successfully established in which the attached Nx_Port is the source of the connect-request.


53-1001156-01

fcFxPortC1OutConnections 1.3.6.1.2.1.75.1.4.1.1.9

3 fcFxPortC1OutConnections 1.3.6.1.2.1.75.1.4.1.1.9

The number of Class 1 connections successfully established in which the attached Nx_Port is the destination of the connect-request.


53-1001156-01

307

3 fcFxPortC1ConnTime 1.3.6.1.2.1.75.1.4.1.1.10

fcFxPortC1ConnTime 1.3.6.1.2.1.75.1.4.1.1.10

The cumulative time that this Fx_Port has been engaged in Class 1 connection. The amount of time is counted from after a connect-request has been accepted until the connection is disengaged, either by an EOFdt or Link Reset.


53-1001156-01



A table that contains Class 2 accounting information recorded since the management agent has reinitialized, one entry for each Fx_Port in the fabric element.


53-1001156-01

309



Augments:


1: fcFxPortEntry


53-1001156-01



The number of Class 2 frames received by this Fx_Port from its attached Nx_Port.


53-1001156-01

311



The number of Class 2 frames delivered through this Fx_Port to its attached Nx_Port.


53-1001156-01





53-1001156-01

313



The number of Class 2 frame octets, including the frame delimiters, delivered through this Fx_Port to its attached Nx_Port.


53-1001156-01





53-1001156-01

315

3 fcFxPortC2FbsyFrames 1.3.6.1.2.1.75.1.4.2.1.6

fcFxPortC2FbsyFrames 1.3.6.1.2.1.75.1.4.2.1.6

The number of F_BSY frames generated by this Fx_Port against Class 2 frames.


53-1001156-01

fcFxPortC2FrjtFrames 1.3.6.1.2.1.75.1.4.2.1.7

3 fcFxPortC2FrjtFrames 1.3.6.1.2.1.75.1.4.2.1.7

The number of F_RJT frames generated by this Fx_Port against Class 2 frames.


53-1001156-01

317



A table that contains Class 3 accounting information recorded since the management agent has reinitialized, one entry for each Fx_Port in the fabric element.


53-1001156-01



Augments:


1: fcFxPortEntry


53-1001156-01

319



The number of Class 3 frames received by this Fx_Port from its attached Nx_Port.


53-1001156-01



The number of Class 3 frames delivered through this Fx_Port to its attached Nx_Port.


53-1001156-01

321





53-1001156-01



The number of Class 3 frame octets, including the frame delimiters, delivered through this Fx_Port to its attached Nx_Port.


53-1001156-01

323




fcFeCapability Group

This group consists of a table describing information about what each Fx_Port is inherently capable of operating or supporting. A capability might be used, as expressed in its respective object value in the Configuration group.



53-1001156-01

fcFxPortCapTable 1.3.6.1.2.1.75.1.5.1

3 fcFxPortCapTable 1.3.6.1.2.1.75.1.5.1

A table that contains the capabilities of the port within the fabric element, one entry for each

Fx_Port.


53-1001156-01

325

3 fcFxPortCapEntry 1.3.6.1.2.1.75.1.5.1.1

fcFxPortCapEntry 1.3.6.1.2.1.75.1.5.1.1

Augments:

An entry containing the capabilities of a Fx_Port.

1: fcFxPortEntry


53-1001156-01

fcFxPortCapFcphVersionHigh 1.3.6.1.2.1.75.1.5.1.1.1

3 fcFxPortCapFcphVersionHigh 1.3.6.1.2.1.75.1.5.1.1.1

The highest or most recent version of FC-PH that the Fx_Port is capable of supporting.


53-1001156-01

327

3 fcFxPortCapFcphVersionLow 1.3.6.1.2.1.75.1.5.1.1.2

fcFxPortCapFcphVersionLow 1.3.6.1.2.1.75.1.5.1.1.2

The lowest or earliest version of FC-PH that the Fx_Port is capable of supporting.


53-1001156-01

fcFxPortCapBbCreditMax 1.3.6.1.2.1.75.1.5.1.1.3

3 fcFxPortCapBbCreditMax 1.3.6.1.2.1.75.1.5.1.1.3

The maximum number of receive buffers available for holding Class 1 connect-request, and Class 2 or Class 3 frames from the attached Nx_Port.


53-1001156-01

329

3 fcFxPortCapBbCreditMin 1.3.6.1.2.1.75.1.5.1.1.4

fcFxPortCapBbCreditMin 1.3.6.1.2.1.75.1.5.1.1.4

The minimum number of receive buffers available for holding Class 1 connect-request, and Class 2 or Class 3 frames from the attached Nx_Port.


53-1001156-01

fcFxPortCapRxDataFieldSizeMax 1.3.6.1.2.1.75.1.5.1.1.5

3 fcFxPortCapRxDataFieldSizeMax 1.3.6.1.2.1.75.1.5.1.1.5

The maximum size (in bytes) of the data field in a frame that the Fx_Port is capable of receiving from its attached Nx_Port.


53-1001156-01

331

3 fcFxPortCapRxDataFieldSizeMin 1.3.6.1.2.1.75.1.5.1.1.6

fcFxPortCapRxDataFieldSizeMin 1.3.6.1.2.1.75.1.5.1.1.6

The minimum size (in bytes) of the data field in a frame that the Fx_Port is capable of receiving from its attached Nx_Port.


53-1001156-01

fcFxPortCapCos 1.3.6.1.2.1.75.1.5.1.1.7

3 fcFxPortCapCos 1.3.6.1.2.1.75.1.5.1.1.7

A value indicating the set of Classes of Service that the Fx_Port is capable of supporting.


53-1001156-01

333

3 fcFxPortCapIntermix 1.3.6.1.2.1.75.1.5.1.1.8

fcFxPortCapIntermix 1.3.6.1.2.1.75.1.5.1.1.8

A flag indicating whether the Fx_Port is capable of supporting the intermixing of Class 2 and Class

3 frames during a Class 1 connection. This flag is only valid if the port is capable of supporting

Class 1 service.


53-1001156-01

fcFxPortCapStackedConnMode 1.3.6.1.2.1.75.1.5.1.1.9

3 fcFxPortCapStackedConnMode 1.3.6.1.2.1.75.1.5.1.1.9

A value indicating the mode of Stacked Connect request that the Fx_Port is capable of supporting.


53-1001156-01

335

3 fcFxPortCapClass2SeqDeliv 1.3.6.1.2.1.75.1.5.1.1.10

fcFxPortCapClass2SeqDeliv 1.3.6.1.2.1.75.1.5.1.1.10

A flag indicating whether the Fx_Port is capable of supporting Class 2 Sequential Delivery.


53-1001156-01





53-1001156-01

337

3 fcFxPortCapHoldTimeMax 1.3.6.1.2.1.75.1.5.1.1.12

fcFxPortCapHoldTimeMax 1.3.6.1.2.1.75.1.5.1.1.12

The maximum holding time (in microseconds) that the Fx_Port is capable of supporting.


53-1001156-01

fcFxPortCapHoldTimeMin 1.3.6.1.2.1.75.1.5.1.1.13

3 fcFxPortCapHoldTimeMin 1.3.6.1.2.1.75.1.5.1.1.13

The minimum holding time (in microseconds) that the Fx_Port is capable of supporting.


53-1001156-01

339

3

FCFABRIC-ELEMENT-MIB (Experimental Branch)

FCFABRIC-ELEMENT-MIB (Experimental Branch)

NOTE

The FCFABRIC-ELEMENT-MIB is supported only in Fabric OS v2.6.x and v3.0.x.

This section contains descriptions and other information that is specific to FCFABRIC-ELEMENT-MIB

(in the experimental branch), including the following:

•

FCFABRIC-ELEMENT-MIB Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341

•

Definitions for FCFABRIC-ELEMENT-MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . 345

•

fcFeConfig Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347

•

fcFeOp Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382

•

fcFeError Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

•

fcFeAcct Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

•

fcFeCap Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

NOTE

Brocade does not support the settable “Write” function for any of the Fibre Channel FE MIB objects except

“fcFxPortPhysAdminStatus 1.3.6.1.2.1.75.1.2.2.1.1” .

The descriptions of each of the MIB variables in this chapter come directly from the

FCFABRIC-ELEMENT-MIB itself. The notes that follow the descriptions typically pertain to

Brocade-specific information and are provided by Brocade.

The object types in FCFABRIC-ELEMENT-MIB are organized into the following groups:

•

Configuration

•

Operational

•

Error

•

Accounting (not supported)

•

Capability


53-1001156-01

FCFABRIC-ELEMENT-MIB Organization

3


Figures

23 through

28

depict the organization and structure of FCFABRIC-ELEMENT-MIB.

- iso

- org

- dod

- internet

- experimental

- fibreChannel

- fcFabric

- fcFe

- fcFeConfig

- fcFabricName

- fcElementName

- fcFeModuleCapacity

- fcFeModuleTable

- fcFxConfTable

- fcFeOp

- fcFxPortOperTable

- fcFxPortPhysTable

- fcFxlogiTable

- fcFeError

- fcFxPortErrorTable

- fcFeAcct

- fcFxPortC1AcctTable



- fcFeCap

- fcFxPortCapTable

FIGURE 23

FCFABRIC-ELEMENT-MIB Overall Tree Structure


53-1001156-01

341

342

3


- fcFeConfig

- fcFabricName 1.3.6.1.3.42.2.1.1.1

- fcElementName 1.3.6.1.3.42.2.1.1.2

- fcFeModuleCapacity 1.3.6.1.3.42.2.1.1.3

- fcFeModuleTable 1.3.6.1.3.42.2.1.1.4

- fcFeModuleEntry 1.3.6.1.3.42.2.1.1.4.1

- fcFeModuleIndex 1.3.6.1.3.42.2.1.1.4.1.1

- fcFeModuleDescr 1.3.6.1.3.42.2.1.1.4.1.2

- fcFeModuleObjectID 1.3.6.1.3.42.2.1.1.4.1.3

- fcFeModuleOperStatus 1.3.6.1.3.42.2.1.1.4.1.4

- fcFeModuleLastChange 1.3.6.1.3.42.2.1.1.4.1.5

- fcFeModuleFxPortCapacity 1.3.6.1.3.42.2.1.1.4.1.6

- fcFeModuleName 1.3.6.1.3.42.2.1.1.4.1.7

- fcFxConfTable 1.3.6.1.3.42.2.1.1.5

- fcFxConfEntry 1.3.6.1.3.42.2.1.1.5.1

- fcFxConfModuleIndex 1.3.6.1.3.42.2.1.1.5.1.1

- fcFxConfFxPortIndex 1.3.6.1.3.42.2.1.1.5.1.2

- fcFxPortName 1.3.6.1.3.42.2.1.1.5.1.3

- fcFxPortFcphVersionHigh 1.3.6.1.3.42.2.1.1.5.1.4

- fcFxPortFcphVersionLow 1.3.6.1.3.42.2.1.1.5.1.5

- fcFxPortBbCredit 1.3.6.1.3.42.2.1.1.5.1.6

- fcFxPortRxBufSize 1.3.6.1.3.42.2.1.1.5.1.7

- fcFxPortRatov 1.3.6.1.3.42.2.1.1.5.1.8

- fcFxPortEdtov 1.3.6.1.3.42.2.1.1.5.1.9

- fcFxPortCosSupported 1.3.6.1.3.42.2.1.1.5.1.10

- fcFxPortIntermixSupported 1.3.6.1.3.42.2.1.1.5.1.11

- fcFxPortStackedConnMode 1.3.6.1.3.42.2.1.1.5.1.12



- fcFxPortHoldTime 1.3.6.1.3.42.2.1.1.5.1.15

- fcFxPortBaudRate 1.3.6.1.3.42.2.1.1.5.1.16

- fcFxPortMedium 1.3.6.1.3.42.2.1.1.5.1.17

- fcFxPortTxType 1.3.6.1.3.42.2.1.1.5.1.18

- fcFxPortDistance 1.3.6.1.3.42.2.1.1.5.1.19

FIGURE 24

fcFeConfig Hierarchy


53-1001156-01


53-1001156-01


3

- fcFeOp

- fcFxPortOperTable 1.3.6.1.3.42.2.1.2.1

- fcFxPortOperEntry 1.3.6.1.3.42.2.1.2.1.1

- fcFxPortOperModuleIndex 1.3.6.1.3.42.2.1.2.1.1.1

- fcFxPortOperFxPortIndex 1.3.6.1.3.42.2.1.2.1.1.2

- fcFxPortID 1.3.6.1.3.42.2.1.2.1.1.3

- fcFPortAttachedPortName 1.3.6.1.3.42.2.1.2.1.1.4

- fcFPortConnectedPort 1.3.6.1.3.42.2.1.2.1.1.5

- fcFxPortBbCreditAvailable 1.3.6.1.3.42.2.1.2.1.1.6

- fcFxPortOperMode 1.3.6.1.3.42.2.1.2.1.1.7

- fcFxPortAdminMode 1.3.6.1.3.42.2.1.2.1.1.8

- fcFxPortPhysTable 1.3.6.1.3.42.2.1.2.3

- fcFxPortPhysEntry 1.3.6.1.3.42.2.1.2.3.1

- fcFxPortPhysModuleIndex 1.3.6.1.3.42.2.1.2.3.1.1

- fcFxPortPhysFxPortIndex 1.3.6.1.3.42.2.1.2.3.1.2

- fcFxPortPhysAdminStatus 1.3.6.1.3.42.2.1.2.3.1.3

- fcFxPortPhysOperStatus 1.3.6.1.3.42.2.1.2.3.1.4

- fcFxPortPhysLastChange 1.3.6.1.3.42.2.1.2.3.1.5

- fcFxPortPhysRttov 1.3.6.1.3.42.2.1.2.3.1.6

- fcFxlogiTable 1.3.6.1.3.42.2.1.2.4

- fcFxlogiEntry 1.3.6.1.3.42.2.1.2.4.1

- fcFxlogiModuleIndex 1.3.6.1.3.42.2.1.2.4.1.1

- fcFxlogiFxPortIndex 1.3.6.1.3.42.2.1.2.4.1.2

- fcFxlogiNxPortIndex 1.3.6.1.3.42.2.1.2.4.1.3

- fcFxPortFcphVersionAgreed 1.3.6.1.3.42.2.1.2.4.1.4

- fcFxPortNxPortBbCredit 1.3.6.1.3.42.2.1.2.4.1.5

- fcFxPortNxPortRxDataFieldSize 1.3.6.1.3.42.2.1.2.4.1.6

- fcFxPortCosSuppAgreed 1.3.6.1.3.42.2.1.2.4.1.7

- fcFxPortIntermixSuppAgreed 1.3.6.1.3.42.2.1.2.4.1.8

- fcFxPortStackedConnModeAgreed 1.3.6.1.3.42.2.1.2.4.1.9



- fcFxPortNxPortName 1.3.6.1.3.42.2.1.2.4.1.12

- fcFxPortConnectedNxPort 1.3.6.1.3.42.2.1.2.4.1.13

- fcFxPortBbCreditModel 1.3.6.1.3.42.2.1.2.4.1.14

FIGURE 25

fcFeOp Hierarchy

- fcFeError (1.3.6.1.3.42.2.1.3)

- fcFxPortErrorTable 1.3.6.1.3.42.2.1.3.1

- fcFxPortErrorEntry 1.3.6.1.3.42.2.1.3.1.1

- fcFxPortErrorModuleIndex 1.3.6.1.3.42.2.1.3.1.1.1

- fcFxPortErrorFxPortIndex 1.3.6.1.3.42.2.1.3.1.1.2

- fcFxPortLinkFailures 1.3.6.1.3.42.2.1.3.1.1.3

- fcFxPortSyncLosses 1.3.6.1.3.42.2.1.3.1.1.4

- fcFxPortSigLosses 1.3.6.1.3.42.2.1.3.1.1.5

- fcFxPortPrimSeqProtoErrors 1.3.6.1.3.42.2.1.3.1.1.6

- fcFxPortInvalidTxWords 1.3.6.1.3.42.2.1.3.1.1.7

- fcFxPortInvalidCrcs 1.3.6.1.3.42.2.1.3.1.1.8

- fcFxPortDelimiterErrors 1.3.6.1.3.42.2.1.3.1.1.9

- fcFxPortAddressIdErrors 1.3.6.1.3.42.2.1.3.1.1.10

- fcFxPortLinkResetIns 1.3.6.1.3.42.2.1.3.1.1.11

- fcFxPortLinkResetOuts 1.3.6.1.3.42.2.1.3.1.1.12

- fcFxPortOlsIns 1.3.6.1.3.42.2.1.3.1.1.13

- fcFxPortOlsOuts 1.3.6.1.3.42.2.1.3.1.1.14

343

344

3


FIGURE 26

fcFeError Hierarchy

- fcFeAcct

(-- Not Supported --)

FIGURE 27

fcFeAcct Hierarchy

- fcFeCap

- fcFxPortCapTable 1.3.6.1.3.42.2.1.5.1

- fcFxPortCapEntry 1.3.6.1.3.42.2.1.5.1.1

- fcFxPortCapModuleIndex 1.3.6.1.3.42.2.1.5.1.1.1

- fcFxPortCapFxPortIndex 1.3.6.1.3.42.2.1.5.1.1.2

- fcFxPortCapFcphVersionHigh 1.3.6.1.3.42.2.1.5.1.1.3

- fcFxPortCapFcphVersionLow 1.3.6.1.3.42.2.1.5.1.1.4

- fcFxPortCapBbCreditMax 1.3.6.1.3.42.2.1.5.1.1.5

- fcFxPortCapBbCreditMin 1.3.6.1.3.42.2.1.5.1.1.6

- fcFxPortCapRxDataFieldSizeMax 1.3.6.1.3.42.2.1.5.1.1.7

- fcFxPortCapRxDataFieldSizeMin 1.3.6.1.3.42.2.1.5.1.1.8

- fcFxPortCapCos 1.3.6.1.3.42.2.1.5.1.1.9

- fcFxPortCapIntermix 1.3.6.1.3.42.2.1.5.1.1.10

- fcFxPortCapStackedConnMode 1.3.6.1.3.42.2.1.5.1.1.11



- fcFxPortCapHoldTimeMax 1.3.6.1.3.42.2.1.5.1.1.14

- fcFxPortCapHoldTimeMin 1.3.6.1.3.42.2.1.5.1.1.15

- fcFxPortCapBaudRates 1.3.6.1.3.42.2.1.5.1.1.16

- fcFxPortCapMedia 1.3.6.1.3.42.2.1.5.1.1.17

FIGURE 28

fcFeCap Hierarchy


53-1001156-01

Definitions for FCFABRIC-ELEMENT-MIB

3


TABLE 8

Type Definition

FCFABRIC-ELEMENT-MIB Definitions

Value

Display string Octet string of size 0 to 255

Milliseconds

Microseconds

FcNameId

FabricName

FcPortName

FcAddressId

FcRxDataFieldSize

FcBbCredit

FcphVersion

FcStackedConnMode

FcCosCap

The following definitions are used for FCFABRIC-ELEMENT-MIB.




FcNameId

FcNameId





Integer from 1 to 3


Description

Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854.

Represents time unit value in milliseconds.

Represents time unit value in microseconds.

World Wide Name or Fibre Channel name associated with an FC entry. This is a Network_Destination_ID or Network_Source_ID composed of a value up to 60 bits wide, occupying the remaining 8 bytes while the first nibble identifies the format of the Name_Identifier.

Name_Identifier hex values:

0 (Ignored)

1 (IEEE 48-bit address)

2 (IEEE extended)

3 (Locally assigned)

4 (32-bit IP address)

The name identifier of a fabric. Each fabric provides a unique fabric name.

Only the following formats are allowed:

IEEE48

Local

The name identifier associated with a port.

Only the following formats are allowed:

IEEE48

IEEE extended

Local

A 24-bit value unique within the address space of a fabric.

Receive Data_Field size.

Buffer-to-buffer credit.

Represents the version of FC-PH supported by an NxPort or FxPort.

1 (none)

2 (transparent)

3 (lockedDown) bit 0 (Class F) bit 1 (Class 1) bit 2 (Class 2) bit 3 (Class 3) bit 4 (Class 4) bit 5 (Class 5) bit 6 (Class 6) bit 7 (reserved for future)


53-1001156-01

345

3


TABLE 8

Type Definition

Fc0BaudRate

Fc0BaudRateCap

Fc0MediaCap

Fc0Medium

Fc0TxType

Fc0Distance

FCFABRIC-ELEMENT-MIB Definitions (Continued)

FcFeModuleCapacity

FcFeFxPortCapacity

FcFeModuleIndex

FcFeFxPortIndex

Value

Integer according to FC-0 baud rates



Integer

Integer

Integer





Description

1 (other) None of below

2 (one-eighth) 155 Mbaud (12.5 MB/s)

4 (quarter) 266 Mbaud (25.0 MB/s)

8 (half) 532 Mbaud (50.0 MB/s)

16 (full) 1 Gbaud (100 MB/s)

32 (double) 2 Gbaud (200 MB/s)

64 (quadruple) 4 Gbaud (400 MB/s)

8 Gbaud (800 MB/s) bit 0 (other) bit 1 (one-eighth) bit 2 (quarter) bit 3 (half) bit 4 (full) bit 5 (double) bit 6 (quadruple) bit 7 (reserved for future) bit 0 (unknown) bit 1 (single mode fibre (sm)) bit 2 (multimode fiber 50 micron (m5)) bit 3 (multimode fiber 62.5 micron (m6)) bit 4 (video cable (tv)) bit 5 (miniature cable (mi)) bit 6 (shielded twisted pair (stp)) bit 7 (twisted wire (tw)) bit 8 (long video (lv)) bits 9-15 (reserved for future use)

1 (unknown)

2 (sm)

4 (m5)

8 (m6)

16 (tv)

32 (mi)

64 (stp)

128 (tw)

256 (lv)

1 (unknown)

2 (longWaveLaser (LL))

3 (shortWaveLaser (SL))

4 (longWaveLED (LE))

5 (electrical (EL))

6 (shortWaveLaser-noOFC (SN))

The FC-0 distance range associated with a port transmitter:

1 (unknown)

2 (long)

3 (intermediate)

4 (short)

Represents the maximum number of modules within a Fabric Element.

Represents the maximum number of FxPorts within a module.

Represents the module index within a conceptual table.

Represents the FxPort index within a conceptual table.


53-1001156-01

fcFeConfig Group

3

TABLE 8

FCFABRIC-ELEMENT-MIB Definitions (Continued)

Type Definition

FcFeNxPortIndex

FcFxPortMode

FcBbCreditModel

Value


Integer

Integer

Description

Represents the NxPort index within a conceptual table.

1 (unknown)

2 (fPort)

3 (flPort)

1 (regular)

2 (alternate)

fcFeConfig Group

This group consists of scalar objects and tables. It contains the configuration and service parameters of the fabric element and the Fx_Ports.

The group represents a set of parameters associated with the fabric element or an Fx_Port to support its Nx_Ports.

Implementation of this group is mandatory.


53-1001156-01

347

3 fcFabricName 1.3.6.1.3.42.2.1.1.1

fcFabricName 1.3.6.1.3.42.2.1.1.1

Return

The Name_Identifier of the fabric to which this fabric element belongs.

Returns the WWN of the primary switch in the fabric.


53-1001156-01

fcElementName 1.3.6.1.3.42.2.1.1.2

Return

The Name_Identifier of the fabric element.

Returns the WWN of the switch.

fcElementName 1.3.6.1.3.42.2.1.1.2

3


53-1001156-01

349

3 fcFeModuleCapacity 1.3.6.1.3.42.2.1.1.3

fcFeModuleCapacity 1.3.6.1.3.42.2.1.1.3

The maximum number of modules in the fabric element, regardless of their current state.

The Brocade 12000, 24000, and 48000 directors do not support this MIB variable.

The Value for fcFeModuleCapacity is always 1 for all the supported switches.


53-1001156-01

fc Fabric Element Module Table

3 fc Fabric Element Module Table

This table contains one entry for each module, information of the modules.


53-1001156-01

351

3 fcFeModuleTable 1.3.6.1.3.42.2.1.1.4

fcFeModuleTable 1.3.6.1.3.42.2.1.1.4

A table that contains, one entry for each module in the fabric element, information of the modules.


53-1001156-01

fcFeModuleEntry 1.3.6.1.3.42.2.1.1.4.1

3 fcFeModuleEntry 1.3.6.1.3.42.2.1.1.4.1

Status

Index

An entry containing the configuration parameters of a module.

Mandatory fcFeModuleIndex


53-1001156-01

353

3 fcFeModuleIndex 1.3.6.1.3.42.2.1.1.4.1.1

fcFeModuleIndex 1.3.6.1.3.42.2.1.1.4.1.1

Identifies the module within the fabric element for which this entry contains information. This value is never greater than fcFeModuleCapacity.


53-1001156-01

fcFeModuleDescr 1.3.6.1.3.42.2.1.1.4.1.2

3 fcFeModuleDescr 1.3.6.1.3.42.2.1.1.4.1.2

A textual description of the module. This value should include the full name and version identification of the module. It should contain printable ASCII characters.

Refer to “sysDescr 1.3.6.1.2.1.1.1” on page 22.


53-1001156-01

355

3 fcFeModuleObjectID 1.3.6.1.3.42.2.1.1.4.1.3

fcFeModuleObjectID 1.3.6.1.3.42.2.1.1.4.1.3

The vendor’s authoritative identification of the module. This value might be allocated within the

SMI enterprises subtree (1.3.6.1.4.1) and provides a straight-forward and unambiguous means for determining what kind of module is being managed.

For example, this object could take the value 1.3.6.1.4.1.99649.3.9 if vendor “Neufe Inc.” was assigned the subtree 1.3.6.1.4.1.99649, and had assigned the identifier 1.3.6.1.4.1.99649.3.9 to its ‘FeFiFo-16 PlugInCard.’

Refer to “sysObjectID 1.3.6.1.2.1.1.2” on page 23.


53-1001156-01

fcFeModuleOperStatus 1.3.6.1.3.42.2.1.1.4.1.4

3 fcFeModuleOperStatus 1.3.6.1.3.42.2.1.1.4.1.4

Indicates the operational status of the module:

• online (1) The module is functioning properly.

• offline (2) The module is not available.

• testing (3) The module is under testing.

• faulty (4) The module is defective in some way.


53-1001156-01

357

3 fcFeModuleLastChange 1.3.6.1.3.42.2.1.1.4.1.5

fcFeModuleLastChange 1.3.6.1.3.42.2.1.1.4.1.5

Contains the value of

“sysUpTime 1.3.6.1.2.1.1.3”

when the module entered its current operational status. A value of 0 indicates that the operational status of the module has not changed since the agent last restarted.


53-1001156-01

fcFeModuleFxPortCapacity 1.3.6.1.3.42.2.1.1.4.1.6

3 fcFeModuleFxPortCapacity 1.3.6.1.3.42.2.1.1.4.1.6

The number of Fx_Port that can be contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to fcFeModuleFxPortCapacity, inclusive; however, the numbers are not required to be contiguous.


53-1001156-01

359

3 fcFeModuleName 1.3.6.1.3.42.2.1.1.4.1.7

fcFeModuleName 1.3.6.1.3.42.2.1.1.4.1.7

The Name_Identifier of the module.

The return value is the WWN of the switch.


53-1001156-01

Fx_Port Configuration Table

3

Fx_Port Configuration Table

This table contains, one entry for each Fx_Port, the configuration parameters of the ports.


53-1001156-01

361

3 fcFxConfTable 1.3.6.1.3.42.2.1.1.5

fcFxConfTable 1.3.6.1.3.42.2.1.1.5

A table that contains, one entry for each Fx_Port in the fabric element, configuration and service parameters of the Fx_Ports.


53-1001156-01

fcFxConfEntry 1.3.6.1.3.42.2.1.1.5.1

3 fcFxConfEntry 1.3.6.1.3.42.2.1.1.5.1

Index

An entry containing the configuration and service parameters of an Fx_Port.

FcFxConfModuleIndex, fcFxConfFxPortIndex


53-1001156-01

363

3 fcFxConfModuleIndex 1.3.6.1.3.42.2.1.1.5.1.1

fcFxConfModuleIndex 1.3.6.1.3.42.2.1.1.5.1.1

Identifies the module containing the Fx_Port for which this entry contains information.


53-1001156-01

fcFxConfFxPortIndex 1.3.6.1.3.42.2.1.1.5.1.2

3 fcFxConfFxPortIndex 1.3.6.1.3.42.2.1.1.5.1.2




53-1001156-01

365

3 fcFxPortName 1.3.6.1.3.42.2.1.1.5.1.3

fcFxPortName 1.3.6.1.3.42.2.1.1.5.1.3

The name identifier of this Fx_Port. Each Fx_Port has a unique port name within the address space of the fabric.

The return value is the WWN of the port.


53-1001156-01

fcFxPortFcphVersionHigh 1.3.6.1.3.42.2.1.1.5.1.4

3 fcFxPortFcphVersionHigh 1.3.6.1.3.42.2.1.1.5.1.4

The highest or most recent version of FC-PH that the Fx_Port is configured to support.


53-1001156-01

367

3 fcFxPortFcphVersionLow 1.3.6.1.3.42.2.1.1.5.1.5

fcFxPortFcphVersionLow 1.3.6.1.3.42.2.1.1.5.1.5

The lowest or earliest version of FC-PH that the Fx_Port is configured to support.


53-1001156-01



The total number of receive buffers available for holding Class 1 connect-request Class 2 or 3 frames from the attached Nx_Port. It is for buffer-to-buffer flow control in the direction from the attached Nx_Port (if applicable) to Fx_Port.

3


53-1001156-01

369

3 fcFxPortRxBufSize 1.3.6.1.3.42.2.1.1.5.1.7

fcFxPortRxBufSize 1.3.6.1.3.42.2.1.1.5.1.7

The largest Data_Field Size (in octets) for an FT_1 frame that can be received by the Fx_Port.


53-1001156-01

fcFxPortRatov 1.3.6.1.3.42.2.1.1.5.1.8

3 fcFxPortRatov 1.3.6.1.3.42.2.1.1.5.1.8

The Resource_Allocation_Timeout Value configured for the Fx_Port. This is used as the time-out value for determining when to reuse an Nx_Port resource such as a Recovery_Qualifier. It represents E_D_TOV (Refer to

“fcFxPortEdtov 1.3.6.1.2.1.75.1.1.5.1.8” on page 248) plus twice the

maximum time that a frame might be delayed within the fabric and still be delivered.


53-1001156-01

371

3 fcFxPortEdtov 1.3.6.1.3.42.2.1.1.5.1.9

fcFxPortEdtov 1.3.6.1.3.42.2.1.1.5.1.9

The E_D_TOV value configured for the Fx_Port. The Error_Detect_Timeout Value is used as the time-out value for detecting an error condition.


53-1001156-01

fcFxPortCosSupported 1.3.6.1.3.42.2.1.1.5.1.10

3 fcFxPortCosSupported 1.3.6.1.3.42.2.1.1.5.1.10

Values

A value indicating the set of Classes of Service supported by the Fx_Port.


•

Class F (0)

•

Class 1 (1)

•

Class 2 (2)

•

Clas 3 (3)

•

Class 4 (4)

•

Class 5 (5)

•

Class 6 (6)


53-1001156-01

373

3 fcFxPortIntermixSupported 1.3.6.1.3.42.2.1.1.5.1.11

fcFxPortIntermixSupported 1.3.6.1.3.42.2.1.1.5.1.11

Values

A flag indicating whether the Fx_Port supports an Intermixed Dedicated Connection.


• yes (1)

• no (2)


53-1001156-01

fcFxPortStackedConnMode 1.3.6.1.3.42.2.1.1.5.1.12

3 fcFxPortStackedConnMode 1.3.6.1.3.42.2.1.1.5.1.12

A value indicating the mode of stacked connect supported by the Fx_Port.


53-1001156-01

375



Values

A flag indicating whether Class 2 sequential delivery is supported by the Fx_Port.


• yes (1)

• no (2)


53-1001156-01



Values

A flag indicating whether Class 3 sequential delivery is supported by the Fx_Port.


• yes (1)

• no (2)


53-1001156-01

377

3 fcFxPortHoldTime 1.3.6.1.3.42.2.1.1.5.1.15

fcFxPortHoldTime 1.3.6.1.3.42.2.1.1.5.1.15

The maximum time (in microseconds) that the Fx_Port holds a frame before discarding the frame if it is unable to deliver the frame. The value 0 means that the Fx_Port does not support this parameter.


53-1001156-01

fcFxPortBaudRate 1.3.6.1.3.42.2.1.1.5.1.16

3 fcFxPortBaudRate 1.3.6.1.3.42.2.1.1.5.1.16

The FC-0 baud rate of the Fx_Port.

The Brocade 12000, 24000, 48000 , and DCX directors do not support this MIB variable.


53-1001156-01

379

3 fcFxPortMedium 1.3.6.1.3.42.2.1.1.5.1.17

fcFxPortMedium 1.3.6.1.3.42.2.1.1.5.1.17

The FC-0 medium of the Fx_Port.


53-1001156-01

fcFxPortTxType 1.3.6.1.3.42.2.1.1.5.1.18

The FC-0 transmitter type of the Fx_Port.

fcFxPortTxType 1.3.6.1.3.42.2.1.1.5.1.18

3


53-1001156-01

381

3 fcFxPortDistance 1.3.6.1.3.42.2.1.1.5.1.19

fcFxPortDistance 1.3.6.1.3.42.2.1.1.5.1.19

The FC-0 distance range of the Fx_Port transmitter.

fcFeOp Group

This group consists of tables that contain operational status and established service parameters for the fabric element and the attached Nx_Ports.

NOTE

Implementation of this group is mandatory.


53-1001156-01

fcFxPortOperTable 1.3.6.1.3.42.2.1.2.1

fcFxPortOperTable 1.3.6.1.3.42.2.1.2.1

A table that contains one entry for each Fx_Port in the fabric element, operational status, and parameters of the Fx_Ports.

3


53-1001156-01

383

3 fcFxPortOperEntry 1.3.6.1.3.42.2.1.2.1.1

fcFxPortOperEntry 1.3.6.1.3.42.2.1.2.1.1

Index

An entry containing operational status and parameters of an Fx_Port.

fcFxPortOperModuleIndex, fcFxPortOperFxPortIndex


53-1001156-01

fcFxPortOperModuleIndex 1.3.6.1.3.42.2.1.2.1.1.1

3 fcFxPortOperModuleIndex 1.3.6.1.3.42.2.1.2.1.1.1



53-1001156-01

385

3 fcFxPortOperFxPortIndex 1.3.6.1.3.42.2.1.2.1.1.2

fcFxPortOperFxPortIndex 1.3.6.1.3.42.2.1.2.1.1.2




53-1001156-01

fcFxPortID 1.3.6.1.3.42.2.1.2.1.1.3

3 fcFxPortID 1.3.6.1.3.42.2.1.2.1.1.3

The address identifier by which this Fx_Port is identified within the fabric. The Fx_Port might assign its address identifier to its attached Nx_Port(s) during fabric login.


53-1001156-01

387

3 fcFPortAttachedPortName 1.3.6.1.3.42.2.1.2.1.1.4

fcFPortAttachedPortName 1.3.6.1.3.42.2.1.2.1.1.4

The port name of the attached N_Port, if applicable. If the value of this object is

‘0000000000000000’H, this Fx_Port has no Nx_Port attached to it. This variable has been deprecated and might be implemented for backward compatibility.


53-1001156-01

fcFPortConnectedPort 1.3.6.1.3.42.2.1.2.1.1.5

fcFPortConnectedPort 1.3.6.1.3.42.2.1.2.1.1.5

The address identifier of the destination Fx_Port with which this Fx_Port is currently engaged in either a Class 1 or loop connection. If the value of this object is ‘000000’H, this Fx_Port is not engaged in a connection. This variable has been deprecated and might be implemented for backward compatibility.

3


53-1001156-01

389

3 fcFxPortBbCreditAvailable 1.3.6.1.3.42.2.1.2.1.1.6

fcFxPortBbCreditAvailable 1.3.6.1.3.42.2.1.2.1.1.6

The number of buffers currently available for receiving frames from the attached port in the buffer-to-buffer flow control. The value should be less than or equal to fcFxPortBbCredit.


53-1001156-01

fcFxPortOperMode 1.3.6.1.3.42.2.1.2.1.1.7

3 fcFxPortOperMode 1.3.6.1.3.42.2.1.2.1.1.7

The current operational mode of the Fx_Port.


53-1001156-01

391

3 fcFxPortAdminMode 1.3.6.1.3.42.2.1.2.1.1.8

fcFxPortAdminMode 1.3.6.1.3.42.2.1.2.1.1.8

The desired operational mode of the Fx_Port.


53-1001156-01

fcFxPortPhysTable 1.3.6.1.3.42.2.1.2.3

3 fcFxPortPhysTable 1.3.6.1.3.42.2.1.2.3

A table that contains, one entry for each Fx_Port in the fabric element, physical level status and parameters of the Fx_Ports.


53-1001156-01

393

3 fcFxPortPhysEntry 1.3.6.1.3.42.2.1.2.3.1

fcFxPortPhysEntry 1.3.6.1.3.42.2.1.2.3.1

Index

An entry containing physical level status and parameters of an Fx_Port.

fcFxPortPhysModuleIndex, fcFxPortPhysFxPortIndex


53-1001156-01

fcFxPortPhysModuleIndex 1.3.6.1.3.42.2.1.2.3.1.1

3 fcFxPortPhysModuleIndex 1.3.6.1.3.42.2.1.2.3.1.1



53-1001156-01

395

3 fcFxPortPhysFxPortIndex 1.3.6.1.3.42.2.1.2.3.1.2

fcFxPortPhysFxPortIndex 1.3.6.1.3.42.2.1.2.3.1.2




53-1001156-01

fcFxPortPhysAdminStatus 1.3.6.1.3.42.2.1.2.3.1.3

3 fcFxPortPhysAdminStatus 1.3.6.1.3.42.2.1.2.3.1.3

The desired state of the Fx_Port:

• online (1) Place port online

• offline (2) Take port offline

• testing (3) Initiate test procedures

A management station might place the Fx_Port in a desired state by setting this object accordingly.

The testing state (3) indicates that no operational frames can be passed. When a fabric element initializes, all Fx_Ports start with fcFxPortPhysAdminStatus in the offline state (2). As the result of either explicit management action or per configuration information accessible by the fabric element, fcFxPortPhysAdminStatus is then changed to either the online (1) or testing (3) states or remains in the offline state (2).


53-1001156-01

397

3 fcFxPortPhysOperStatus 1.3.6.1.3.42.2.1.2.3.1.4

fcFxPortPhysOperStatus 1.3.6.1.3.42.2.1.2.3.1.4

The current operational status of the Fx_Port:

• online (1) Log in might proceed.

• offline (2) Log in cannot proceed.

• testing (3) Port is under test.

• link-failure (4) Failure after online/testing.

The testing state (3) indicates that no operational frames can be passed. If fcFxPortPhysAdminStatus is offline (2), then fcFxPortPhysOperStatus should be offline (2). If fcFxPortPhysAdminStatus is changed to online (1), then fcFxPortPhysOperStatus should change to

1 (online) if the Fx_Port is ready to accept fabric login request from the attached Nx_Port; it should proceed and remain in the link-failure state (4) if and only if there is a fault that prevents it from going to the online state (1).


53-1001156-01

fcFxPortPhysLastChange 1.3.6.1.3.42.2.1.2.3.1.5

3 fcFxPortPhysLastChange 1.3.6.1.3.42.2.1.2.3.1.5

The value of sysUpTime at the time the Fx_Port entered its current operational status. A value of 0 indicates that the Fx_Port’s operational status has not changed since the agent last restarted.


53-1001156-01

399

3 fcFxPortPhysRttov 1.3.6.1.3.42.2.1.2.3.1.6

fcFxPortPhysRttov 1.3.6.1.3.42.2.1.2.3.1.6

The Receiver_Transmitter_Timeout value of the Fx_Port. This is used by the receiver logic to detect

Loss of Synchronization.


53-1001156-01


3


This table contains one entry for each Fx_Port in the fabric element, and the Service Parameters that have been established from the most recent fabric login, whether implicit or explicit.


53-1001156-01

401

3 fcFxlogiTable 1.3.6.1.3.42.2.1.2.4

fcFxlogiTable 1.3.6.1.3.42.2.1.2.4

A table that contains, one entry for each Fx_Port in the fabric element, services parameters established from the most recent fabric login, explicit or implicit.


53-1001156-01

fcFxlogiEntry 1.3.6.1.3.42.2.1.2.4.1

3 fcFxlogiEntry 1.3.6.1.3.42.2.1.2.4.1

Index

An entry containing service parameters established from a successful fabric login.

fcFxloginModuleIndex, fcFxloginFxPortIndex, fcFxloginNxPortIndex


53-1001156-01

403

3 fcFxlogiModuleIndex 1.3.6.1.3.42.2.1.2.4.1.1

fcFxlogiModuleIndex 1.3.6.1.3.42.2.1.2.4.1.1



53-1001156-01

fcFxlogiFxPortIndex 1.3.6.1.3.42.2.1.2.4.1.2

3 fcFxlogiFxPortIndex 1.3.6.1.3.42.2.1.2.4.1.2




53-1001156-01

405

3 fcFxlogiNxPortIndex 1.3.6.1.3.42.2.1.2.4.1.3

fcFxlogiNxPortIndex 1.3.6.1.3.42.2.1.2.4.1.3

The object identifies the associated Nx_Port in the attachment for which the entry contains information.


53-1001156-01

fcFxPortFcphVersionAgreed 1.3.6.1.3.42.2.1.2.4.1.4

3 fcFxPortFcphVersionAgreed 1.3.6.1.3.42.2.1.2.4.1.4

The version of FC-PH that the Fx_Port has agreed to support from the fabric login.


53-1001156-01

407

3 fcFxPortNxPortBbCredit 1.3.6.1.3.42.2.1.2.4.1.5

fcFxPortNxPortBbCredit 1.3.6.1.3.42.2.1.2.4.1.5

The total number of buffers available for holding Class 1 connect-request Class 2 or Class 3 frames to be transmitted to the attached Nx_Port. It is for buffer-to-buffer flow control in the direction from

Fx_Port to Nx_Port. The buffer-to-buffer flow control mechanism is indicated in the respective fcFxPortBbCreditModel.


53-1001156-01

fcFxPortNxPortRxDataFieldSize 1.3.6.1.3.42.2.1.2.4.1.6

3 fcFxPortNxPortRxDataFieldSize 1.3.6.1.3.42.2.1.2.4.1.6

The Receive Data Field Size of the attached Nx_Port. This is a binary value that specifies the largest

Data Field Size for an FT_1 frame that can be received by the Nx_Port. The value is a number of bytes in the range 128 to 2112, inclusive.


53-1001156-01

409

3 fcFxPortCosSuppAgreed 1.3.6.1.3.42.2.1.2.4.1.7

fcFxPortCosSuppAgreed 1.3.6.1.3.42.2.1.2.4.1.7

Indicates that the attached Nx_Port has requested the Fx_Port for the support of classes of services and the Fx_Port has granted the request.


53-1001156-01

fcFxPortIntermixSuppAgreed 1.3.6.1.3.42.2.1.2.4.1.8

3 fcFxPortIntermixSuppAgreed 1.3.6.1.3.42.2.1.2.4.1.8

Values

A variable indicating that the attached Nx_Port has requested the Fx_Port for Intermix support and the Fx_Port has granted the request. This flag is only valid if Class 1 service is supported.


• yes (1)

• no (2)


53-1001156-01

411

3 fcFxPortStackedConnModeAgreed 1.3.6.1.3.42.2.1.2.4.1.9

fcFxPortStackedConnModeAgreed 1.3.6.1.3.42.2.1.2.4.1.9

Indicates whether the Fx_Port has agreed to support stacked connect from the fabric login. This is only meaningful if Class 1 service has been agreed to.


53-1001156-01



Values

A variable indicating whether the Fx_Port has agreed to support Class 2 sequential delivery from the fabric login. This is only meaningful if Class 2 service has been agreed.


• yes (1)

• no (2)


53-1001156-01

413



Values

A flag indicating whether the Fx_Port has agreed to support Class 3 sequential delivery from the fabric login. This is only meaningful if Class 3 service has been agreed to.


• yes (1)

• no (2)


53-1001156-01

fcFxPortNxPortName 1.3.6.1.3.42.2.1.2.4.1.12

3 fcFxPortNxPortName 1.3.6.1.3.42.2.1.2.4.1.12

The port name of the attached Nx_Port, if applicable. If the value of this object is

‘0000000000000000’H, this Fx_Port has no Nx_Port attached to it.


53-1001156-01

415

3 fcFxPortConnectedNxPort 1.3.6.1.3.42.2.1.2.4.1.13


The address identifier of the destination Fx_Port with which this Fx_Port is currently engaged in either a Class 1 or loop connection. If the value of this object is ‘000000’H, this Fx_Port is not engaged in a connection.


53-1001156-01

fcFxPortBbCreditModel 1.3.6.1.3.42.2.1.2.4.1.14

3 fcFxPortBbCreditModel 1.3.6.1.3.42.2.1.2.4.1.14

Identifies the BB_Credit model used by the Fx_Port. The regular model refers to the buffer-to-buffer flow control mechanism defined in FC-PH [1] used between the F_Port and the N_Port. For

FL_Ports, the alternate buffer-to-buffer flow control mechanism as defined in FC-AL [4] is used between the FL_Port and any attached NL_Ports.

fcFeError Group

This group consists of tables that contain information about the various types of errors detected.

The management station might use the information in this group to determine the quality of the link between the Fx_Port and its attached Nx_Port.



53-1001156-01

417

3 fcFxPortErrorTable 1.3.6.1.3.42.2.1.3.1

fcFxPortErrorTable 1.3.6.1.3.42.2.1.3.1

This table contains one entry for each Fx_Port in the fabric element, and counters recording numbers of errors detected since the management agent reinitialized.

The first six columnar objects after the port index correspond to the counters in the Link

ErrorStatus Block.


53-1001156-01

fcFxPortErrorEntry 1.3.6.1.3.42.2.1.3.1.1

3 fcFxPortErrorEntry 1.3.6.1.3.42.2.1.3.1.1

Index

An entry containing error counters of an Fx_Port.

fcFxPortErrorModuleIndex, fcFxPortErrorFxPortIndex


53-1001156-01

419

3 fcFxPortErrorModuleIndex 1.3.6.1.3.42.2.1.3.1.1.1

fcFxPortErrorModuleIndex 1.3.6.1.3.42.2.1.3.1.1.1



53-1001156-01

fcFxPortErrorFxPortIndex 1.3.6.1.3.42.2.1.3.1.1.2

3 fcFxPortErrorFxPortIndex 1.3.6.1.3.42.2.1.3.1.1.2




53-1001156-01

421

3 fcFxPortLinkFailures 1.3.6.1.3.42.2.1.3.1.1.3

fcFxPortLinkFailures 1.3.6.1.3.42.2.1.3.1.1.3

The number of link failures detected by this Fx_Port.


53-1001156-01

fcFxPortSyncLosses 1.3.6.1.3.42.2.1.3.1.1.4

3 fcFxPortSyncLosses 1.3.6.1.3.42.2.1.3.1.1.4

The number of loss of synchronization errors detected by the Fx_Port.


53-1001156-01

423

3 fcFxPortSigLosses 1.3.6.1.3.42.2.1.3.1.1.5

fcFxPortSigLosses 1.3.6.1.3.42.2.1.3.1.1.5

The number of loss of signal errors detected by the Fx_Port.


53-1001156-01

fcFxPortPrimSeqProtoErrors 1.3.6.1.3.42.2.1.3.1.1.6

3 fcFxPortPrimSeqProtoErrors 1.3.6.1.3.42.2.1.3.1.1.6

The number of primitive sequence protocol errors detected by the Fx_Port.


53-1001156-01

425

3 fcFxPortInvalidTxWords 1.3.6.1.3.42.2.1.3.1.1.7

fcFxPortInvalidTxWords 1.3.6.1.3.42.2.1.3.1.1.7

The number of invalid transmission word errors detected by the Fx_Port.


53-1001156-01

fcFxPortInvalidCrcs 1.3.6.1.3.42.2.1.3.1.1.8

3 fcFxPortInvalidCrcs 1.3.6.1.3.42.2.1.3.1.1.8

The number of invalid Cyclic Redundancy Checks (CRCs) detected by this Fx_Port.


53-1001156-01

427

3 fcFxPortDelimiterErrors 1.3.6.1.3.42.2.1.3.1.1.9

fcFxPortDelimiterErrors 1.3.6.1.3.42.2.1.3.1.1.9

The number of Delimiter errors detected by this Fx_Port.


53-1001156-01

fcFxPortAddressIdErrors 1.3.6.1.3.42.2.1.3.1.1.10

3 fcFxPortAddressIdErrors 1.3.6.1.3.42.2.1.3.1.1.10

The number of address identifier errors detected by this Fx_Port.


53-1001156-01

429

3 fcFxPortLinkResetIns 1.3.6.1.3.42.2.1.3.1.1.11

fcFxPortLinkResetIns 1.3.6.1.3.42.2.1.3.1.1.11

The number of Link Reset Protocol errors received by this Fx_Port from the attached Nx_Port.


53-1001156-01

fcFxPortLinkResetOuts 1.3.6.1.3.42.2.1.3.1.1.12

3 fcFxPortLinkResetOuts 1.3.6.1.3.42.2.1.3.1.1.12

The number of Link Reset Protocol errors issued by this Fx_Port to the attached Nx_Port.


53-1001156-01

431

3 fcFxPortOlsIns 1.3.6.1.3.42.2.1.3.1.1.13

fcFxPortOlsIns 1.3.6.1.3.42.2.1.3.1.1.13

The number of Offline Sequence errors received by this Fx_Port.


53-1001156-01

fcFxPortOlsOuts 1.3.6.1.3.42.2.1.3.1.1.14

3 fcFxPortOlsOuts 1.3.6.1.3.42.2.1.3.1.1.14

The number of Offline Sequence errors issued by this Fx_Port.

fcFeAcct Group

Brocade supports fcFxPortC2AccountingTable and fcFxPortC3AccountingTable.

fcFeCap Group

This group consists of a table describing information about what each Fx_Port is inherently capable of operating or supporting. A capability might be used or not, as expressed in its respective object value in the Configuration group.



53-1001156-01

433

3 fcFxPortCapTable 1.3.6.1.3.42.2.1.5.1

fcFxPortCapTable 1.3.6.1.3.42.2.1.5.1

A table that contains one entry for each Fx_Port, and the capabilities of the port within the fabric element.


53-1001156-01

fcFxPortCapEntry 1.3.6.1.3.42.2.1.5.1.1

3 fcFxPortCapEntry 1.3.6.1.3.42.2.1.5.1.1

Index

An entry containing the capabilities of a Fx_Port.

fcFxPortCapModuleIndex, fcFxPortCapFxPortIndex


53-1001156-01

435

3 fcFxPortCapModuleIndex 1.3.6.1.3.42.2.1.5.1.1.1

fcFxPortCapModuleIndex 1.3.6.1.3.42.2.1.5.1.1.1



53-1001156-01

fcFxPortCapFxPortIndex 1.3.6.1.3.42.2.1.5.1.1.2

3 fcFxPortCapFxPortIndex 1.3.6.1.3.42.2.1.5.1.1.2




53-1001156-01

437

3 fcFxPortCapFcphVersionHigh 1.3.6.1.3.42.2.1.5.1.1.3

fcFxPortCapFcphVersionHigh 1.3.6.1.3.42.2.1.5.1.1.3

The highest or most recent version of FC-PH that the Fx_Port is capable of supporting.


53-1001156-01

fcFxPortCapFcphVersionLow 1.3.6.1.3.42.2.1.5.1.1.4

3 fcFxPortCapFcphVersionLow 1.3.6.1.3.42.2.1.5.1.1.4

The lowest or earliest version of FC-PH that the Fx_Port is capable of supporting.


53-1001156-01

439

3 fcFxPortCapBbCreditMax 1.3.6.1.3.42.2.1.5.1.1.5

fcFxPortCapBbCreditMax 1.3.6.1.3.42.2.1.5.1.1.5

The maximum number of receive buffers available for holding Class 1 connect-request Class 2 or

Class 3 frames from the attached Nx_Port.


53-1001156-01

fcFxPortCapBbCreditMin 1.3.6.1.3.42.2.1.5.1.1.6

3 fcFxPortCapBbCreditMin 1.3.6.1.3.42.2.1.5.1.1.6

The minimum number of receive buffers available for holding Class 1 connect-request Class 2 or

Class 3 frames from the attached Nx_Port.


53-1001156-01

441

3 fcFxPortCapRxDataFieldSizeMax 1.3.6.1.3.42.2.1.5.1.1.7

fcFxPortCapRxDataFieldSizeMax 1.3.6.1.3.42.2.1.5.1.1.7

The maximum size (in bytes) of the Data Field in a frame that the Fx_Port is capable of receiving from its attached Nx_Port.


53-1001156-01

fcFxPortCapRxDataFieldSizeMin 1.3.6.1.3.42.2.1.5.1.1.8

3 fcFxPortCapRxDataFieldSizeMin 1.3.6.1.3.42.2.1.5.1.1.8

The minimum size (in bytes) of the Data Field in a frame that the Fx_Port is capable of receiving from its attached Nx_Port.


53-1001156-01

443

3 fcFxPortCapCos 1.3.6.1.3.42.2.1.5.1.1.9

fcFxPortCapCos 1.3.6.1.3.42.2.1.5.1.1.9

A value indicating the set of Classes of Service that the Fx_Port is capable of supporting.


53-1001156-01

fcFxPortCapIntermix 1.3.6.1.3.42.2.1.5.1.1.10

3 fcFxPortCapIntermix 1.3.6.1.3.42.2.1.5.1.1.10

Values

A flag indicating whether the Fx_Port is capable of supporting the intermixing of Class 2 and Class

3 frames during a Class 1 connection. This flag is only valid if the port is capable of supporting

Class 1 service.


• yes (1)

• no (2)


53-1001156-01

445

3 fcFxPortCapStackedConnMode 1.3.6.1.3.42.2.1.5.1.1.11

fcFxPortCapStackedConnMode 1.3.6.1.3.42.2.1.5.1.1.11

A value indicating the mode of Stacked Connect request that the Fx_Port is capable of supporting.


53-1001156-01



Values



• yes (1)

• no (2)


53-1001156-01

447



Values



• yes (1)

• no (2)


53-1001156-01

fcFxPortCapHoldTimeMax 1.3.6.1.3.42.2.1.5.1.1.14

3 fcFxPortCapHoldTimeMax 1.3.6.1.3.42.2.1.5.1.1.14

The maximum holding time (in microseconds) that the Fx_Port is capable of supporting.


53-1001156-01

449

3 fcFxPortCapHoldTimeMin 1.3.6.1.3.42.2.1.5.1.1.15

fcFxPortCapHoldTimeMin 1.3.6.1.3.42.2.1.5.1.1.15

The minimum holding time (in microseconds) that the Fx_Port is capable of supporting.


53-1001156-01

fcFxPortCapBaudRates 1.3.6.1.3.42.2.1.5.1.1.16

3 fcFxPortCapBaudRates 1.3.6.1.3.42.2.1.5.1.1.16

A value indicating the set of baud rates that the Fx_Port is capable of supporting. This variable has been deprecated and might be implemented for backward compatibility.


53-1001156-01

451

3 fcFxPortCapMedia 1.3.6.1.3.42.2.1.5.1.1.17

fcFxPortCapMedia 1.3.6.1.3.42.2.1.5.1.1.17

A value indicating the set of media that the Fx_Port is capable of supporting. This variable has been deprecated and might be implemented for backward compatibility.


53-1001156-01

Entity MIB Objects

Chapter

4

This chapter provides descriptions and other information specific to Entity MIB object types and includes the following information:

•

Entity MIB Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453

•

Textual Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457

•

Entity MIB Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459

•

Physical Entity Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460

•

Logical Entity Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480

•

Entity Mapping Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490

•

General Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

•

Entity MIB Trap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501

•

Entity MIB Conformance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502

Entity MIB Overview

Entity MIB is the module for representing multiple logical entities supported by a single SNMP agent. This MIB is supported only in Fabric OS v4.x, v5.x, v6.0, and v6.1.

The descriptions of each of the MIB variables in this chapter come directly from Entity MIB itself.

The notes that follow the descriptions typically pertain to Brocade-specific information and are provided by Brocade.

The object types in Entity MIB are organized into the following groupings:

•

Entity MIB Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459

•

Entity MIB Trap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501

•

Entity MIB Conformance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502


53-1001156-01

453

454

4

Entity MIB Overview

Entity MIB System Organization of MIB Objects

Figure 29 through

Figure 36

depict the organization and structure of the Entity MIB file system.

- iso

- org

- dod

- internet

- mgmt

- mib-2

- entityMIB

- entityMIBObjects

- entityPhysical

- entityLogical

- entityMapping

- entityGeneral

- entityMIBTraps

- entityMIBTrapPrefix

- entityConformance

- entityCompliances

- entityGroups

FIGURE 29

Overall Tree Structure for Entity MIB

- entityPhysical

- entPhysicalTable 1.3.6.1.2.1.47.1.1.1

- entPhysicalEntry 1.3.6.1.2.1.47.1.1.1.1

- entPhysicalIndex 1.3.6.1.2.1.47.1.1.1.1.1

- entPhysicalDescr 1.3.6.1.2.1.47.1.1.1.1.2

- entPhysicalVendorType 1.3.6.1.2.1.47.1.1.1.1.3

- entPhysicalContainedIn 1.3.6.1.2.1.47.1.1.1.1.4

- entPhysicalClass 1.3.6.1.2.1.47.1.1.1.1.5

- entPhysicalParentRelPos 1.3.6.1.2.1.47.1.1.1.1.6

- entPhysicalName 1.3.6.1.2.1.47.1.1.1.1.7

- entPhysicalHardwareRev 1.3.6.1.2.1.47.1.1.1.1.8

- entPhysicalFirmwareRev 1.3.6.1.2.1.47.1.1.1.1.9

- entPhysicalSoftwareRev 1.3.6.1.2.1.47.1.1.1.1.10

- entPhysicalSerialNum 1.3.6.1.2.1.47.1.1.1.1.11

- entPhysicalMfgName 1.3.6.1.2.1.47.1.1.1.1.12

- entPhysicalModelName 1.3.6.1.2.1.47.1.1.1.1.13

- entPhysicalAlias 1.3.6.1.2.1.47.1.1.1.1.14

- entPhysicalAssetID 1.3.6.1.2.1.47.1.1.1.1.15

- entPhysicalIsFRU 1.3.6.1.2.1.47.1.1.1.1.16

FIGURE 30

entityPhysical Hierarchy

- entityLogical

- entLogicalTable 1.3.6.1.2.1.47.1.2.1

- entLogicalEntry 1.3.6.1.2.1.47.1.2.1.1

- entLogicalIndex 1.3.6.1.2.1.47.1.2.1.1.1

- entLogicalDescr 1.3.6.1.2.1.47.1.2.1.1.2

- entLogicalType 1.3.6.1.2.1.47.1.2.1.1.3

- entLogicalCommunity 1.3.6.1.2.1.47.1.2.1.1.4

- entLogicalTAddress 1.3.6.1.2.1.47.1.2.1.1.5

- entLogicalTDomain 1.3.6.1.2.1.47.1.2.1.1.6

- entLogicalContextEngineID 1.3.6.1.2.1.47.1.2.1.1.7

- entLogicalContextName 1.3.6.1.2.1.47.1.2.1.1.8

FIGURE 31

entityLogical Hierarchy


53-1001156-01


53-1001156-01

Entity MIB Overview

4

- entityMapping

- entLPMappingTable 1.3.6.1.2.1.47.1.3.1

- entLPMappingEntry 1.3.6.1.2.1.47.1.3.1.1

- entLPPhysicalIndex 1.3.6.1.2.1.47.1.3.1.1.1

- entAliasMappingTable 1.3.6.1.2.1.47.1.3.2

- entAliasMappingEntry 1.3.6.1.2.1.47.1.3.2.1

- entAliasLogicalIndexOrZero 1.3.6.1.2.1.47.1.3.2.1.1

- entAliasMappingIdentifier 1.3.6.1.2.1.47.1.3.2.1.2

- entPhysicalContainsTable 1.3.6.1.2.1.47.1.3.3

- entPhysicalContainsEntry 1.3.6.1.2.1.47.1.3.3.1

- entPhysicalChildIndex 1.3.6.1.2.1.47.1.3.3.1.1

FIGURE 32

entityMapping Hierarchy

- entityGeneral

- entLastChangeTime 1.3.6.1.2.1.47.1.4.1

FIGURE 33

entityGeneral Hierarchy

- entityMIBTraps

- entityMIBTrapPrefix (1.3.6.1.2.1.47.2.0)

- entConfigChange 1.3.6.1.2.1.47.2.0.1

FIGURE 34

entityMIBTrapPrefix Hierarchy

- entityConformance

- entityCompliances (1.3.6.1.2.1.47.3.1)

- entityCompliance 1.3.6.1.2.1.47.3.1.1

- entity2Compliance 1.3.6.1.2.1.47.3.1.2

- entityGroups (1.3.6.1.2.1.47.3.2)

- entityPhysicalGroup 1.3.6.1.2.1.47.3.2.1

- entityLogicalGroup 1.3.6.1.2.1.47.3.2.2

- entityMappingGroup 1.3.6.1.2.1.47.3.2.3

- entityGeneralGroup 1.3.6.1.2.1.47.3.2.4

- entityNotificationsGroup 1.3.6.1.2.1.47.3.2.5

- entityPhysical2Group 1.3.6.1.2.1.47.3.2.6

- entityLogical2Group 1.3.6.1.2.1.47.3.2.7

FIGURE 35

entityConformance Hierarchy

Definitions for Entity MIB

Table 9

lists the objects or definitions that are imported into the Entity MIB and the modules from which they are imported.

TABLE 9

Object

Objects Imported into the Entity MIB

Imported from this module

MODULE-IDENTITY

OBJECT-TYPE

NOTIFICATION-TYPE mib-2

SNMPv2-SMI

455

4

Entity MIB Overview

TABLE 9

Object

Objects Imported into the Entity MIB (Continued)

Imported from this module

SNMPv2-TC TDomain

TAddress

TEXTUAL-CONVENTION

AutonomousType

RowPointer

TimeStamp

TruthValue

MODULE-COMPLIANCE

OBJECT-GROUP

NOTIFICATION-GROUP

SnmpAdminString

SNMPv2-CONF

SNMP-FRAMEWORK-MIB


53-1001156-01

Textual Conventions

4

Textual Conventions

PhysicalIndex

Syntax

Arbitrary value that uniquely identifies the physical entity. Value should be a small positive integer; index values for different physical entities are not necessarily contiguous.

Integer (1... 2147483647)


53-1001156-01

457

4

PhysicalClass

PhysicalClass

Syntax

An enumerated value that provides an indication of the general hardware type of a particular physical entity. There are no restrictions as to the number of entPhysicalEntries of each entPhysicalClass, which must be instantiated by an agent.

Integer

TABLE 10

Possible Values for PhysicalClass

Values Description other (1) unknown (2) chassis (3) backplane (4) container (5) powerSupply (6) fan (7) sensor (8) module (9) port (10) stack (11)

The physical entity class is known but does not match any of the supported values.

The physical entity class is unknown to the agent.

The physical entity class is an overall container for networking equipment. Any class of physical entity except a stack can be contained within a chassis, and a chassis might be contained only within a stack.

The physical entity class is a device for aggregating and forwarding networking traffic, such as a shared backplane in a modular Ethernet switch. Note that an agent might model a backplane as a single physical entity, which is actually implemented as multiple discrete physical components (within a chassis or stack).

The physical entity class is capable of containing one ore more removable physical entities, possibly of different types (such as a chassis slot or daughter-card holder). For example, each

(empty or full) slot in a chassis is modeled as a container. Note that all removable physical entities should be modeled within a container entity, such as field-replaceable modules, fans, or power supplies. Note that all known containers, including empty containers, should be modeled by the agent.

The physical entity class is a power-supplying component.

The physical entity class is a fan or other heat-reduction component.

The physical entity class is a sensor, such as a temperature sensor within a router chassis.

The physical entity class is a self-contained subsystem (such as a plug-in card or daughter-card). If it is removable, then it should be modeled within a container entity; otherwise, it should be modeled directly within another physical entity (for example, a chassis or another module).

The physical entity class is a networking port, capable of receiving or transmitting networking traffic.

The physical entity class is a super-container (possibly virtual), intended to group together multiple chassis entities (such as a stack of multiple chassis entities). A stack might be realized by a virtual cable or a real interconnect cable attached to multiple chassis, or it can comprise multiple interconnect cables. A stack should not be modeled within any other physical entities, but a stack might be contained within another stack. Only chassis entities should be contained within a stack.


53-1001156-01

SnmpEngineIdOrNone

4

SnmpEngineIdOrNone

Syntax

A specially formatted SnmpEngineID string for use with the Entity MIB.

If an instance of an object with syntax SnmpEngineIdOrNone has a non-zero length, then the object encoding and semantics are defined by the SnmpEngineID textual convention (Refer to RFC 2571

[RFC2571]).

If an instance of an object with syntax SnmpEngineIdOrNone contains a zero-length string, then no appropriate SnmpEngineID is associated with the logical entity (that is, SNMPv3 not supported).

•

For the Brocade 3016 or Brocade 4020 blades, the snmpEngineID takes the UUID value. For example, if the UUID value is A9914D56-1E5A-0E59-C51E-528802B06E4F, the snmpEngineID displays

80.00.06.34.B1.A9.91.4D.56.1E.5A.0E.59.C5.1E.52.88.02.B0.6E.4F (hex)

•

For other switches, the snmpEngineID takes the WWN. For example, if the WWN value is

10:00:00:05:1e:35:d5:ee, the snmpEngineID displays

80.00.06.34.B2.10.00.00.05.1E.35.D5.EE (hex)

•

If the WWN cannot be taken, the snmpEngineID takes the IP address + port number along with the private enterprise number and algorithm type used. An example of this type of snmpEngineID would be

00.00.06.34.00.00.00.A1.0A.20.93.CA (hex)

OCTET STRING (SIZE(0..32)) Empty string or SnmpEngineID

Entity MIB Objects

The Entity MIB objects are divided into the following groups:

•

Physical Entity Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460

•

Logical Entity Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480

•

Entity Mapping Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490

•

General Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

The following sections list the MIBs in each group.


53-1001156-01

459

4

Physical Entity Group

Physical Entity Group

entPhysicalTable 1.3.6.1.2.1.47.1.1.1

This table contains one row per physical entity ( Figure 36 ). The table always contains at least one

row for an “overall” physical entity.

This object is implemented for Fabric OS v6.2.0. The “overall” physical entry for Brocade is the chassis, and in Fabric OS v6.2.0 it is marked as a FRU.

TABLE 11

entPhysicalTable Entries for Brocade Switches

Platform Blades Fans Power Supply WWN Card

Brocade 200E

Brocade 3016

Brocade 3250

Brocade 3850

Brocade 3900

Brocade 4012

Brocade 4100

Brocade 4900

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000 / 24000

Brocade 48000

Brocade DCX

Brocade DCX-4S

Brocade Encrytion Switch

Brocade 300

1

1

1

1

1

NA

1

1

1

1

1

10 blades

10 blades

8 blades

4 blades

NA

1 blade

3 fans not a FRU

NA

3 fans not a FRU

4 fans not a FRU

6 fans in 3 FRUs

NA

3 FRUs

3 FRUs

3 FRUs

3 FRUs

3 FRUs

3 fans

3 fans

3 fans

2 fans

3 fans

3 fans

1 PS not a FRU

NA

4 PS

2 PS

2 PS

1 PS

1 PS not a FRU

2 PS not a FRU

2 PS

NA

2 PS

2 PS

2 PS

2 PS

2 PS

4 PS

4 PS

1 WWN unit not a FRU





NA






2 WWN units in 1

FRU

2 WWN units in 1

FRU

2 WWN units

1 WWN unit

1 WWN unit

1 WWN unit. Not a

FRU.


53-1001156-01


53-1001156-01

entPhysicalTable 1.3.6.1.2.1.47.1.1.1

4

TABLE 11

entPhysicalTable Entries for Brocade Switches

Platform Blades Fans

Brocade 5100 1 blade 2 fans

Brocade 5300 1 blade 3 fans

Power Supply

2 PS

2 PS

WWN Card

1 WWN unit. Not a

FRU.

1 WWN unit. Not a

FRU.

Chassis: one entry

Container: one entry for each FRU slot

Power supply if the PS is not a FRU, it will be directly below the chassis

Module if the Module is not a FRU, it will be directly below the chassis

Fan

If the Fan is not a

FRU, it will be directly below the chassis

FIGURE 36

entPhysicalTable Containment Hierarchy (entPhysicalContainsTable)

461

4 entPhysicalEntry 1.3.6.1.2.1.47.1.1.1.1

entPhysicalEntry 1.3.6.1.2.1.47.1.1.1.1

Index

Information about a particular physical entity.

Each entry provides objects (entPhysicalDescr, entPhysicalVendorType, and entPhysicalClass) to help an NMS identify and characterize the entry, and objects (entPhysicalContainedIn and entPhysicalParentRelPos) to help an NMS relate the particular entry to other entries in this table.

1: entPhysicalIndex


53-1001156-01

entPhysicalIndex 1.3.6.1.2.1.47.1.1.1.1.1

4 entPhysicalIndex 1.3.6.1.2.1.47.1.1.1.1.1

The index for this entry. This object is not accessible.


53-1001156-01

463

4 entPhysicalDescr 1.3.6.1.2.1.47.1.1.1.1.2

entPhysicalDescr 1.3.6.1.2.1.47.1.1.1.1.2

A textual description of the physical entity (physical name of the entity, such as chassis, blade, port, and so on). This object should contain a string that identifies the entity manufacturer’s name and should be set to a distinct value for each version or model of the physical entity.

The name provides the entity type and number (for example, slot 1, power supply, and so on). The description gives the textual description of the type of the entry (for example, power supply, module, and so on).


53-1001156-01

entPhysicalVendorType 1.3.6.1.2.1.47.1.1.1.1.3

4 entPhysicalVendorType 1.3.6.1.2.1.47.1.1.1.1.3

Returns

An indication of the vendor-specific hardware type of the physical entity. Note that this is different from the definition of MIB-II sysObjectID.

An agent should set this object to an enterprise-specific registration identifier value, indicating the specific equipment type in detail. The associated instance of entPhysicalClass indicates the general type of hardware device.

If no vendor-specific registration identifier exists for this physical entity, or if the value is unknown by this agent, then the value { 0, 0 } is returned.

Currently, NULL OID { 0, 0 } is returned.


53-1001156-01

465

4 entPhysicalContainedIn 1.3.6.1.2.1.47.1.1.1.1.4

entPhysicalContainedIn 1.3.6.1.2.1.47.1.1.1.1.4

The value of entPhysicalIndex for the physical entity that “contains” this physical entity. A value of

0 indicates this physical entity is not contained in any other physical entity. Note that the set of containment relationships define a strict hierarchy; that is, recursion is not allowed.

In the event a physical entity is contained by more than one physical entity (for example, double-wide modules), this object should identify the containing entity with the lowest value of entPhysicalIndex.

Value 0 for chassis entry. All containers have ContainedIn set to 1. All FRUs are contained in their respective slot container entries.


53-1001156-01

entPhysicalClass 1.3.6.1.2.1.47.1.1.1.1.5

4 entPhysicalClass 1.3.6.1.2.1.47.1.1.1.1.5

An indication of the general hardware type of the physical entity.

An agent should set this object to the standard enumeration value that most accurately indicates the general class of the physical entity, or the primary class if there is more than one.

If no appropriate standard registration identifier exists for this physical entity, then the value other(1)

is returned. If the value is unknown by this agent, then the value unknown(2)

is returned.

Brocade 300 switches can have the following hierarchy of physical objects:

•

Chassis: One entry (one row)

•

Container: One entry for each FRU slot (one blade, one power supply, three fans)

•

Module: one entry for blades, one entry for power supply, and three entries for fans.


•


•

Container: One entry for each FRU slot (one blade, two power supplies, two fans)

•

Module: One entry for blades, two entries for power supplies, and two entries for fans.


•


•

Container: One entry for each FRU slot (one blade,two power supplies, three fans)

•

Module: One entry for blades, two entries for power supplies, and three entries for fans.

Brocade DCX directors can have the following hierarchy of physical objects:

•


•

Container: One entry for each FRU slot (eight port blades, two CPs, four power supplies, three fans)

•

Module: Eight entries for port blades, two entries for CPs, four entries for power supplies, and three entries for fans.

Brocade DCX-4S directors can have the following hierarchy of physical objects:

•


•

Container: One entry for each FRU slot (four port blades, two CPs, two power supplies, two fans)

•


Brocade 12000, 24000, and 48000 directors can have the following hierarchy of physical objects:

•


•

Container: One entry for each FRU slot (eight port blades, two CPs, four power supplies, three fans)

•



•


•

Container: One entry for each FRU slot (one switch blade, two power supplies, six fans)


53-1001156-01

467

4 entPhysicalClass 1.3.6.1.2.1.47.1.1.1.1.5

•

Module: One entry for switch blade, up to two entries for power supplies, and up to six entries for fans.


•


•

Container: One entry for each FRU slot (one switch blade, two power supplies, three fans)

•

Module: 1 entry for switch blade, up to two entries for power supplies, and up to three entries for fans.

Brocade 7500 and 7600 switches can have the following hierarchy of physical objects:

•


•

Container: One entry for each FRU slot (one switch blade, two power supplies, three fans)

-

Module: 1 entry for switch blade, up to two entries for power supplies, and up to three entries for fans.


53-1001156-01

entPhysicalParentRelPos 1.3.6.1.2.1.47.1.1.1.1.6

4 entPhysicalParentRelPos 1.3.6.1.2.1.47.1.1.1.1.6

An indication of the relative position of this child component among all its sibling components.

Sibling components are defined as entPhysicalEntries that share the same instance values of each of the entPhysicalContainedIn and entPhysicalClass objects.

For chassis entry, this value is -1; for containers, it is the sequential number of the container from the first one; for all FRUs, it is always 1.

An NMS can use this object to identify the relative ordering for all sibling components of a particular parent (identified by the entPhysicalContainedIn instance in each sibling entry).

This value should match any external labeling of the physical component if possible. For example, for a container (such as a card slot) labeled slot #3, entPhysicalParentRelPos should have the value 3. Note that the entPhysicalEntry for the module plugged into slot 3 should have an entPhysicalParentRelPos value of 1.

If the physical position of this component does not match any external numbering or clearly visible ordering, then user documentation or other external reference material should be used to determine the parent-relative position. If this is not possible, then the agent should assign a consistent (but possibly arbitrary) ordering to a given set of sibling components, perhaps based on internal representation of the components.

If the agent cannot determine the parent-relative position for some reason, or if the associated value of entPhysicalContainedIn is 0, then the value -1 is returned; otherwise, a non-negative integer is returned, indicating the parent-relative position of this physical entity.

Parent-relative ordering normally starts from 1 and continues to n, where n represents the highest-positioned child entity. However, if the physical entities (for example, slots) are labeled from a starting position of zero, then the first sibling should be associated with an entPhysicalParentRelPos value of 0. Note that this ordering might be sparse or dense, depending on agent implementation.

The actual values returned are not globally meaningful, as each parent component might use different numbering algorithms. The ordering is meaningful only among siblings of the same parent component.

The agent should retain parent-relative position values across reboots, either through algorithmic assignment or use of nonvolatile storage.


53-1001156-01

469

4 entPhysicalName 1.3.6.1.2.1.47.1.1.1.1.7

entPhysicalName 1.3.6.1.2.1.47.1.1.1.1.7

The textual name of the physical entity (physical name of the entity such as chassis, blade, port, and so on). The value of this object should be the name of the component as assigned by the local device and should be suitable for use in commands entered at the device’s “console.” This might be a text name, such as “console,” or a simple component number (for example, port or module number) such as 1, depending on the physical component naming syntax of the device.

If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

Note that the value of entPhysicalName for two physical entities is the same in the event that the console interface does not distinguish between them (for example, slot-1 and the card in slot-1).

The name provides the type of the entry and its number (for example, slot 1, power supply, and so on). The description gives the textual description of the type of the entry (for example, power supply, module, and so on)


53-1001156-01

entPhysicalHardwareRev 1.3.6.1.2.1.47.1.1.1.1.8

4 entPhysicalHardwareRev 1.3.6.1.2.1.47.1.1.1.1.8

The vendor-specific hardware revision string for the physical entity. The preferred value is the hardware revision identifier actually printed on the component itself (if present).

Note that if revision information is stored internally in a nonprintable (for example, binary) format, then the agent must convert such information to a printable format, in an implementation-specific manner.

If no specific hardware revision string is associated with the physical component, or if this information is unknown to the agent, then this object will contain a zero-length string.

Set to an empty string.


53-1001156-01

471

4 entPhysicalFirmwareRev 1.3.6.1.2.1.47.1.1.1.1.9

entPhysicalFirmwareRev 1.3.6.1.2.1.47.1.1.1.1.9

The vendor-specific firmware revision string for the physical entity.


If no specific firmware programs are associated with the physical component, or if this information is unknown to the agent, then this object will contain a zero-length string.

Set to an empty string.


53-1001156-01

entPhysicalSoftwareRev 1.3.6.1.2.1.47.1.1.1.1.10

4 entPhysicalSoftwareRev 1.3.6.1.2.1.47.1.1.1.1.10

The vendor-specific software revision string for the physical entity.


If no specific software programs are associated with the physical component, or if this information is unknown to the agent, then this object will contain a zero-length string.

Set to empty string.


53-1001156-01

473

4 entPhysicalSerialNum 1.3.6.1.2.1.47.1.1.1.1.11

entPhysicalSerialNum 1.3.6.1.2.1.47.1.1.1.1.11

The vendor-specific serial number string for the physical entity. The preferred value is the serial number actually printed on the component (if present).

On the first instantiation of a physical entity, the value of entPhysicalSerialNum associated with that entity is set to the correct vendor-assigned serial number, if this information is available to the agent. If a serial number is unknown or nonexistent, the entPhysicalSerialNum is set to a zero-length string instead.

Note that implementations that can correctly identify the serial numbers of all installed physical entities do not need to provide write access to the entPhysicalSerialNum object. Agents that cannot provide nonvolatile storage for the entPhysicalSerialNum strings are not required to implement write access for this object.

Not every physical component has a serial number or even needs one. Physical entities for which the associated value of the entPhysicalIsFRU object is equal to “false(2)” (for example, the repeater ports within a repeater module), do not need their own unique serial number. An agent does not have to provide write access for such entities and might return a zero-length string.

If write access is implemented for an instance of entPhysicalSerialNum and a value is written into the instance, the agent must retain the supplied value in the entPhysicalSerialNum instance associated with the same physical entity for as long as that entity remains instantiated. This includes instantiations across all reinitializations/reboots of the network management system, including those that result in a change of the physical entity’s entPhysicalIndex value.

Set to serial number and part number (if available), respectively.

NOTE

For the Brocade 4024 blade, entPhysicalSerialNum displays the vendor-specific serial number; for other switches it displays the factory serial number.


53-1001156-01

entPhysicalMfgName 1.3.6.1.2.1.47.1.1.1.1.12

4 entPhysicalMfgName 1.3.6.1.2.1.47.1.1.1.1.12

The name of the manufacturer of this physical component. The preferred value is the name actually printed on the component (if present).

Note that comparisons between instances of the entPhysicalModelName, entPhysicalFirmwareRev, entPhysicalSoftwareRev, and the entPhysicalSerialNum objects are meaningful only amongst entPhysicalEntries with the same value of entPhysicalMfgName.

If the manufacturer name string associated with the physical component is unknown to the agent, then this object contains a zero-length string.



53-1001156-01

475

4 entPhysicalModelName 1.3.6.1.2.1.47.1.1.1.1.13

entPhysicalModelName 1.3.6.1.2.1.47.1.1.1.1.13

The vendor-specific model name associated with this physical component. The preferred value is the customer-visible part number, which might be printed on the component.

If the model name string associated with the physical component is unknown to the agent, then this object contains a zero-length string.

Set to serial number and part number (if available) respectively.


53-1001156-01

entPhysicalAlias 1.3.6.1.2.1.47.1.1.1.1.14

4 entPhysicalAlias 1.3.6.1.2.1.47.1.1.1.1.14

This object is an alias name for the physical entity as specified by a network manager; it provides a nonvolatile handle for the physical entity.

On the first instantiation of a physical entity, the value of entPhysicalAlias associated with that entity is set to the zero-length string. However, the agent might set the value to a locally unique default value instead of a zero-length string.

If write access is implemented for an instance of entPhysicalAlias and a value is written into the instance, the agent must retain the supplied value in the entPhysicalAlias instance associated with the same physical entity for as long as that entity remains instantiated. This includes instantiations across all reinitializations/reboots of the network management system, including those that result in a change of the physical entity’s entPhysicalIndex value.



53-1001156-01

477

4 entPhysicalAssetID 1.3.6.1.2.1.47.1.1.1.1.15

entPhysicalAssetID 1.3.6.1.2.1.47.1.1.1.1.15

This object is a user-assigned asset tracking identifier for the physical entity as specified by a network manager; it provides nonvolatile storage of this information.

On the first instantiation of a physical entity, the value of entPhysicalAssetID associated with that entity is set to the zero-length string.

Not every physical component has an asset tracking identifier or even need one. Physical entities for which the associated value of the entPhysicalIsFRU object is equal to “false(2)” (for example, the repeater ports within a repeater module) do not need their own unique asset tracking identifier.

An agent does not have to provide write access for such entities and might instead return a zero-length string.

If write access is implemented for an instance of entPhysicalAssetID and a value is written into the instance, the agent must retain the supplied value in the entPhysicalAssetID instance associated with the same physical entity for as long as that entity remains instantiated. This includes instantiations across all re-initializations/reboots of the network management system, including those that result in a change of the physical entity’s entPhysicalIndex value.

If no asset tracking information is associated with the physical component, then this object contains a zero-length string.



53-1001156-01

entPhysicalIsFRU 1.3.6.1.2.1.47.1.1.1.1.16

4 entPhysicalIsFRU 1.3.6.1.2.1.47.1.1.1.1.16

The entPhysicalIsFRU object indicates whether this physical entity is considered a field replaceable unit by the vendor. If this object contains the value “true(1),” then this entPhysicalEntry identifies a field replaceable unit. For all entPhysicalEntries representing components that are permanently contained within a field replaceable unit, the value “false(2)” should be returned for this object.

Set to True (1) for FRU entries (port blades, CPs, sensors, power supplies, and fans; False (2) for container and chassis type entries.


53-1001156-01

479

4

Logical Entity Group

Logical Entity Group

entLogicalTable 1.3.6.1.2.1.47.1.2.1

This table contains one row per logical entity. For agents that implement more than one naming scope, at least one entry must exist. Agents that instantiate all MIB objects within a single naming scope are not required to implement this table.


53-1001156-01

entLogicalEntry 1.3.6.1.2.1.47.1.2.1.1

entLogicalEntry 1.3.6.1.2.1.47.1.2.1.1

Index

Information about a particular logical entity. Entities might be managed by this agent or other

SNMP agents in the same chassis.

entLogicalIndex

4


53-1001156-01

481

4 entLogicalIndex 1.3.6.1.2.1.47.1.2.1.1.1

entLogicalIndex 1.3.6.1.2.1.47.1.2.1.1.1

The value of this object uniquely identifies the logical entity. The value should be a small positive integer; index values for different logical entities are not necessarily contiguous.


53-1001156-01

entLogicalDescr 1.3.6.1.2.1.47.1.2.1.1.2

4 entLogicalDescr 1.3.6.1.2.1.47.1.2.1.1.2

A textual description of the logical entity. This object should contain a string that identifies the manufacturer’s name for the logical entity and should be set to a distinct value for each version of the logical entity.


53-1001156-01

483

4 entLogicalType 1.3.6.1.2.1.47.1.2.1.1.3

entLogicalType 1.3.6.1.2.1.47.1.2.1.1.3

An indication of the type of logical entity. This is typically the Object Identifier name of the node in the SMI’s naming hierarchy that represents the major MIB module, or the majority of the MIB modules, supported by the logical entity.

• a logical entity of a regular host/router -> mib-2

• a logical entity of a 802.1d bridge -> dot1dBridge

• a logical entity of a 802.3 repeater -> snmpDot3RptrMgmt

If an appropriate node in the SMI’s naming hierarchy cannot be identified, the value mib-2 should be used.


53-1001156-01

entLogicalCommunity 1.3.6.1.2.1.47.1.2.1.1.4

4 entLogicalCommunity 1.3.6.1.2.1.47.1.2.1.1.4

An SNMPv1 or SNMPv2C community string, which can be used to access detailed management information for this logical entity. The agent should allow read access with this community string

(to an appropriate subset of all managed objects) and might also return a community string based on the privileges of the request used to read this object.

Note that an agent might return a community string with read-only privileges, even if this object is accessed with a read-write community string. However, the agent must take care not to return a community string that allows more privileges than the community string used to access this object.

A compliant SNMP agent might want to conserve naming scopes by representing multiple logical entities in a single default naming scope. This is possible when the logical entities represented by the same value of entLogicalCommunity have no object instances in common. For example,

“bridge1” and “repeater1” might be part of the main naming scope, but at least one additional community string is needed to represent “bridge2” and “repeater2.”

Logical entities “bridge1” and “repeater1” would be represented by sysOREntries associated with the default naming scope.

For agents not accessible through SNMPvl or SNMPv2C, the value of this object is the empty string.

This object might also contain an empty string if a community string has not yet been assigned by the agent, or no community string with suitable access rights can be returned for a particular

SNMP request.

Note that this object is deprecated. Agents that implement SNMPv3 access should use the entLogicalContextEngineID and entLogicalContextName objects to identify the context associated with each logical entity. SNMPv3 agents might return a zero-length string for this object or might continue to return a community string (for example, tri-lingual agent support).


53-1001156-01

485

4 entLogicalTAddress 1.3.6.1.2.1.47.1.2.1.1.5

entLogicalTAddress 1.3.6.1.2.1.47.1.2.1.1.5

The transport service address by which the logical entity receives network management traffic, formatted according to the corresponding value of entLogicalTDomain.

For snmpUDPDomain, a TAddress is 6 octets long, the initial 4 octets containing the IP-address in network-byte order and the last 2 containing the UDP port in network-byte order. Refer to Transport

Mappings for Version 2 of the Simple Network Management Protocol (RFC1906) for further information on snmpUDPDomain.


53-1001156-01

entLogicalTDomain 1.3.6.1.2.1.47.1.2.1.1.6

4 entLogicalTDomain 1.3.6.1.2.1.47.1.2.1.1.6

Indicates the kind of transport service by which the logical entity receives network management traffic. Possible values for this object are currently found in the Transport Mappings for SNMPv2 document (RFC1906).


53-1001156-01

487

4 entLogicalContextEngineID 1.3.6.1.2.1.47.1.2.1.1.7

entLogicalContextEngineID 1.3.6.1.2.1.47.1.2.1.1.7

The authoritative contextEngineID that can be used to send an SNMP message concerning information held by this logical entity to the address specified by the associated entLogicalTAddress/entLogicalTDomain pair.

This object, together with the associated entLogicalContextName object, defines the context associated with a particular logical entity; it allows access to SNMP engines identified by a contextEngineId and contextName pair.

If no value has been configured by the agent, a zero-length string is returned, or the agent might choose not to instantiate this object at all.


53-1001156-01

entLogicalContextName 1.3.6.1.2.1.47.1.2.1.1.8

4 entLogicalContextName 1.3.6.1.2.1.47.1.2.1.1.8

The contextName that can be used to send an SNMP message concerning information held by this logical entity to the address specified by the associated entLogicalTAddress/entLogicalTDomain pair.

This object, together with the associated entLogicalContextEngineID object, defines the context associated with a particular logical entity and allows access to SNMP engines identified by a contextEngineId and contextName pair.

If no value has been configured by the agent, a zero-length string is returned, or the agent might choose not to instantiate this object at all.


53-1001156-01

489

4

Entity Mapping Group

Entity Mapping Group

entLPMappingTable 1.3.6.1.2.1.47.1.3.1

This table contains zero or more rows of logical entity to physical equipment associations. For each logical entity known by this agent, there are zero or more mappings to the physical resources used to realize that logical entity.

An agent should limit the number and nature of entries in this table such that only meaningful and nonredundant information is returned. For example, in a system that contains a single power supply, mappings between logical entities and the power supply are not useful and should not be included.

Also, only the most appropriate physical component that is closest to the root of a particular containment tree should be identified in an entLPMapping entry.

Suppose a bridge is realized on a particular module and all ports on that module are ports on this bridge. A mapping between the bridge and the module would be useful, but additional mappings between the bridge and each of the ports on that module would be redundant (since the entPhysicalContainedIn hierarchy can provide the same information). If, however, more than one bridge was utilizing ports on this module, then mappings between each bridge and the ports it used would be appropriate.

Also, in the case of a single backplane repeater, a mapping for the backplane to the single repeater entity is not necessary.


53-1001156-01

entLPMappingEntry 1.3.6.1.2.1.47.1.3.1.1

entLPMappingEntry 1.3.6.1.2.1.47.1.3.1.1

Index

Information about a particular logical entity to physical equipment association. Note that the nature of the association is not specifically identified in this entry. It is expected that sufficient information exists in the MIBs used to manage a particular logical entity to infer how physical component information is utilized.

entLogicalIndex entLPPhysicalIndex

4


53-1001156-01

491

4 entLPPhysicalIndex 1.3.6.1.2.1.47.1.3.1.1.1

entLPPhysicalIndex 1.3.6.1.2.1.47.1.3.1.1.1

The value of this object identifies the index value of a particular entPhysicalEntry associated with the indicated entLogicalEntity.


53-1001156-01

entAliasMappingTable 1.3.6.1.2.1.47.1.3.2

4 entAliasMappingTable 1.3.6.1.2.1.47.1.3.2

This table contains zero or more rows, representing mappings of logical entity and physical component to external MIB identifiers. Each physical port in the system might be associated with a mapping to an external identifier, which itself is associated with a particular logical entity’s naming scope. A wildcard mechanism is provided to indicate that an identifier is associated with more than one logical entity.


53-1001156-01

493

4 entAliasMappingEntry 1.3.6.1.2.1.47.1.3.2.1

entAliasMappingEntry 1.3.6.1.2.1.47.1.3.2.1

Index

Information about a particular physical equipment, logical entity to external identifier binding. Each logical entity/physical component pair might be associated with one alias mapping. The logical

entity index might also be used as a wildcard (Refer to “entAliasLogicalIndexOrZero

1.3.6.1.2.1.47.1.3.2.1.1” on page 495 for details.)

Note that only entPhysicalIndex values that represent physical ports (that is, associated entPhysicalClass value is “port(10)”) are permitted to exist in this table.

entPhysicalIndex entAliasLogicalIndexOrZero


53-1001156-01

entAliasLogicalIndexOrZero 1.3.6.1.2.1.47.1.3.2.1.1

4 entAliasLogicalIndexOrZero 1.3.6.1.2.1.47.1.3.2.1.1

The value of this object identifies the logical entity that defines the naming scope for the associated instance of the entAliasMappingIdentifier object.

If this object has a nonzero value, then it identifies the logical entity named by the same value of entLogicalIndex.

If this object has a value of zero, then the mapping between the physical component and the alias identifier for this entAliasMapping entry is associated with all unspecified logical entities. That is, a value of zero (the default mapping) identifies any logical entity that does not have an explicit entry in this table for a particular entPhysicalIndex/entAliasMappingIdentifier pair.

For example, to indicate that a particular interface (such as “physical component 33”) is identified by the same value of ifIndex for all logical entities, the following instance might exist: entAliasMappingIdentifier.33.0 = ifIndex.5

In the event an entPhysicalEntry is associated differently for some logical entities, additional entAliasMapping entries might exist:

entAliasMappingIdentifier.33.0 = ifIndex.6




Note that entries with nonzero entAliasLogicalIndexOrZero index values have precedence over any zero-indexed entry. In this example, all logical entities except 4, 5, and 10 associate physical entity

33 with ifIndex.6.


53-1001156-01

495

4 entAliasMappingIdentifier 1.3.6.1.2.1.47.1.3.2.1.2

entAliasMappingIdentifier 1.3.6.1.2.1.47.1.3.2.1.2

The value of this object identifies a particular conceptual row associated with the indicated entPhysicalIndex and entLogicalIndex pair.

Since only physical ports are modeled in this table, only entries that represent interfaces or ports are allowed. If an ifEntry exists on behalf of a particular physical port, then this object should identify the associated ifEntry. For repeater ports, the appropriate row in the rptrPortGroupTable should be identified instead.

For example, suppose a physical port was represented by entPhysicalEntry.3, entLogicalEntry.15 existed for a repeater, and entLogicalEntry.22 existed for a bridge. Then there might be two related instances of entAliasMappingIdentifier: entAliasMappingIdentifier.3.15 == rptrPortGroupIndex.5.2

entAliasMappingIdentifier.3.22 == ifIndex.17

It is possible that other mappings (besides interfaces and repeater ports) might be defined in the future, as required.

Bridge ports are identified by examining the Bridge MIB and appropriate ifEntries associated with each dot1dBasePort and are thus not represented in this table.


53-1001156-01

entPhysicalContainsTable 1.3.6.1.2.1.47.1.3.3

4 entPhysicalContainsTable 1.3.6.1.2.1.47.1.3.3

A table that exposes the container/containee relationships between physical entities. This table provides all the information found by constructing the virtual containment tree for a given entPhysicalTable, but in a more direct format.

In the event a physical entity is contained by more than one other physical entity (for example, double-wide modules), this table should include these additional mappings, which cannot be represented in the entPhysicalTable virtual containment tree.


53-1001156-01

497

4 entPhysicalContainsEntry 1.3.6.1.2.1.47.1.3.3.1

entPhysicalContainsEntry 1.3.6.1.2.1.47.1.3.3.1

Indexes

A single container / containee relationship.

1: entPhysicalIndex

2: entPhysicalChildIndex


53-1001156-01

entPhysicalChildIndex 1.3.6.1.2.1.47.1.3.3.1.1

4 entPhysicalChildIndex 1.3.6.1.2.1.47.1.3.3.1.1

The value of entPhysicalIndex for the contained physical entity.


53-1001156-01

499

4

General Group

General Group

entLastChangeTime 1.3.6.1.2.1.47.1.4.1

The value of sysUpTime at the time a conceptual row is created, modified, or deleted in any of the following tables:

• entPhysicalTable

• entLogicalTable

• entLPMappingTable

• entAliasMappingTable

• entPhysicalContainsTable


53-1001156-01

Entity MIB Trap

4

Entity MIB Trap

This section lists the entityMIBTrap objects. entConfigChange 1.3.6.1.2.1.47.2.0.1

An entConfigChange notification is generated when the value of entLastChangeTime changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls.

An agent should not generate more than one entConfigChange notification event in a given time interval (five seconds is the suggested default). A notification event is the transmission of a single trap or inform PDU to a list of notification destinations.

If additional configuration changes occur within the throttling period, then notification events for these changes should be suppressed by the agent until the current throttling period expires. At the end of a throttling period, one notification event should be generated if any configuration changes occurred since the start of the throttling period; in such a case, another throttling period is started right away.

An NMS should periodically check the value of entLastChangeTime to detect any missed entConfigChange notification events, for example, due to throttling or transmission loss.


53-1001156-01

501

4

Entity MIB Conformance Information

Entity MIB Conformance Information

This section lists the entityConformance MIBs.

Figure 35 on page 455 shows the structure of the

entityConformance group.

entityCompliance 1.3.6.1.2.1.47.3.1.1

Status

Mandatory

Groups

The compliance statement for SNMP entities that implement version 1 of the Entity MIB.

Deprecated

1: entityPhysicalGroup

2: entityLogicalGroup

3: entityMappingGroup

4: entityGeneralGroup

5: entityNotificationsGroup


53-1001156-01

entity2Compliance 1.3.6.1.2.1.47.3.1.2

4 entity2Compliance 1.3.6.1.2.1.47.3.1.2

Mandatory

Groups

Components

The compliance statement for SNMP entities that implement version 2 of the Entity MIB.

1: entityPhysicalGroup

2: entityPhysical2Group

3: entityGeneralGroup

4: entityNotificationsGroup

1. Type: Group

Group: entityLogical2Group

Description: Implementation of this group is not mandatory for agents which model all MIB object instances within a single naming scope.

2. Type: Group

Group: entityMappingGroup

Description: Implementation of the entPhysicalContainsTable is mandatory for all agents.

Implementation of the entLPMappingTable and entAliasMappingTables are not mandatory for agents which model all MIB object instances within a single naming scope. Note that the entAliasMappingTable may be useful for all agents, however implementation of the entityLogicalGroup or entityLogical2Group is required to support this table.

3. Type: Object

Object: entPhysicalSerialNum

Min access: not-accessible

Description: Read and write access is not required for agents which cannot identify serial number information for physical entities, and/or cannot provide non-volatile storage for

NMS-assigned serial numbers. Write access is not required for agents which can identify serial number information for physical entities, but cannot provide non-volatile storage for

NMS-assigned serial.


53-1001156-01

503

4 entityPhysicalGroup 1.3.6.1.2.1.47.3.2.1

entityPhysicalGroup 1.3.6.1.2.1.47.3.2.1

Objects

The collection of objects used to represent physical system components, for which a single agent provides management information.

1: entPhysicalDescr

2: entPhysicalVendorType

3: entPhysicalContainedIn

4: entPhysicalClass

5: entPhysicalParentRelPos

6: entPhysicalName


53-1001156-01

entityLogicalGroup 1.3.6.1.2.1.47.3.2.2

4 entityLogicalGroup 1.3.6.1.2.1.47.3.2.2

Objects

Status

The collection of objects used to represent the list of logical entities, for which a single agent provides management information.

1: entLogicalDescr

2: entLogicalType

3: entLogicalCommunity

4: entLogicalTAddress

5: entLogicalTDomain

Deprecated


53-1001156-01

505

4 entityMappingGroup 1.3.6.1.2.1.47.3.2.3

entityMappingGroup 1.3.6.1.2.1.47.3.2.3

Objects

The collection of objects used to represent the associations between multiple logical entities, physical components, interfaces, and port identifiers, for which a single agent provides management information.

1: entLPPhysicalIndex

2: entAliasMappingIdentifier

3: entPhysicalChildIndex


53-1001156-01

entityGeneralGroup 1.3.6.1.2.1.47.3.2.4

4 entityGeneralGroup 1.3.6.1.2.1.47.3.2.4

Objects

The collection of objects that are used to represent general entity information for which a single agent provides management information.

1: entLastChangeTime


53-1001156-01

507

4 entityNotificationsGroup 1.3.6.1.2.1.47.3.2.5

entityNotificationsGroup 1.3.6.1.2.1.47.3.2.5

Notifications

The collection of notifications used to indicate Entity MIB data consistency and general status information.

1: entConfigChange


53-1001156-01

entityPhysical2Group 1.3.6.1.2.1.47.3.2.6

4 entityPhysical2Group 1.3.6.1.2.1.47.3.2.6

Objects

The collection of objects used to represent physical system components, for which a single agent provides management information. This group augments the objects contained in the entityPhysicalGroup.

1: entPhysicalHardwareRev

2: entPhysicalFirmwareRev

3: entPhysicalSoftwareRev

4: entPhysicalSerialNum

5: entPhysicalMfgName

6: entPhysicalModelName

7: entPhysicalAlias

8: entPhysicalAssetID

9: entPhysicalIsFRU


53-1001156-01

509

4 entityLogical2Group 1.3.6.1.2.1.47.3.2.7

entityLogical2Group 1.3.6.1.2.1.47.3.2.7

Objects

The collection of objects used to represent the list of logical entities, for which a single SNMP entity provides management information.

1: entLogicalDescr

2: entLogicalType

3: entLogicalTAddress

4: entLogicalTDomain

5: entLogicalContextEngineID

6: entLogicalContextName


53-1001156-01

SW-MIB Objects

Chapter

5

This chapter contains descriptions and other information specific to FC Switch MIB (SW-MIB) object types. This chapter provides information on:

•

SW MIB Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511

•

sw Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522

•

swSystem Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532

•

swFabric Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568

•

SW Agent Configuration Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593

•

Fibre Channel Port Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598

•

Name Server Database Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639

•

Event Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656

•

Fabric Watch Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666

•

End Device Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711

•

Switch Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721

•

ASIC Performance Monitoring Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732

•

Trunking Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 753

SW MIB Overview

The descriptions of the MIB variables in this chapter come directly from the FC Switch MIB. The notes that follow the descriptions typically pertain to Brocade-specific information as provided by

Brocade.

SW-MIB System Organization of MIB Objects

Figure 37

through Figure 50 depict the organization and structure of SW-MIB.

- iso

- org

- dod

- internet

- private

- enterprises

- bsci

- commDev

- fibreChannel

- fcSwitch

- sw

- swTrapsV2

- swSystem

- swFabric

- swModule


53-1001156-01

511

512

5

SW MIB Overview

- swAgtCfg

- swFCport

- swNs

- swEvent

- swFwSystem

- swEndDevice

- swGroup

- swBlmPerfMnt

- swTrunk

- sw28k

- sw21kN24k

- sw20x0

- bsciReg

- bsciModules

- sw21kN24k

- sw20x0

FIGURE 37

SW-MIB Overall Tree Structure

- swTrapsV2

- swFault 1.3.6.1.4.1.1588.2.1.1.1.0.1

- swSensorScn 1.3.6.1.4.1.1588.2.1.1.1.0.2

- swFCPortScn 1.3.6.1.4.1.1588.2.1.1.1.0.3

- swEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.4

- swFabricWatchTrap 1.3.6.1.4.1.1588.2.1.1.1.0.5

- swTrackChangesTrap 1.3.6.1.4.1.1588.2.1.1.1.0.6

- swIPv6ChangeTrap 1.3.6.1.4.1.1588.2.1.1.1.0.7

- swPmgrEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.8

FIGURE 38

swTrapsV2 Hierarchy


53-1001156-01


53-1001156-01

SW MIB Overview

5

- swSystem

- swCurrentDate 1.3.6.1.4.1.1588.2.1.1.1.1.1

- swBootDate 1.3.6.1.4.1.1588.2.1.1.1.1.2

- swFWLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.3

- swFlashLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.4

- swBootPromLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.5

- swFirmwareVersion 1.3.6.1.4.1.1588.2.1.1.1.1.6

- swOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.7

- swAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.8

- swTelnetShellAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.9

- swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10

- swFlashDLOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.11

- swFlashDLAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.12

- swFlashDLHost 1.3.6.1.4.1.1588.2.1.1.1.1.13

- swFlashDLUser 1.3.6.1.4.1.1588.2.1.1.1.1.14

- swFlashDLFile 1.3.6.1.4.1.1588.2.1.1.1.1.15

- swFlashDLPassword 1.3.6.1.4.1.1588.2.1.1.1.1.16

- swBeaconOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.18

- swBeaconAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.19

- swDiagResult 1.3.6.1.4.1.1588.2.1.1.1.1.20

- swNumSensors 1.3.6.1.4.1.1588.2.1.1.1.1.21

- swSensorTable 1.3.6.1.4.1.1588.2.1.1.1.1.22

- swSensorEntry 1.3.6.1.4.1.1588.2.1.1.1.1.22.1

- swSensorIndex 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1

- swSensorType 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2

- swSensorStatus 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3

- swSensorValue 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4

- swSensorInfo 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5

- swTrackChangesInfo 1.3.6.1.4.1.1588.2.1.1.1.1.23

- swID 1.3.6.1.4.1.1588.2.1.1.1.1.24

- swEtherIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.25

- swEtherIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.26

- swFCIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.27

- swFCIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.28

- swIPv6Address 1.3.6.1.4.1.1588.2.1.1.1.1.29

- swIPv6Status 1.3.6.1.4.1.1588.2.1.1.1.1.30

- swModel 1.3.6.1.4.1.1588.2.1.1.1.1.31

FIGURE 39

swSystem Hierarchy

513

514

5

SW MIB Overview

- swFabric

- swDomainID 1.3.6.1.4.1.1588.2.1.1.1.2.1

- swPrincipalSwitch 1.3.6.1.4.1.1588.2.1.1.1.2.2

- swNumNbs 1.3.6.1.4.1.1588.2.1.1.1.2.8

- swVfId 1.3.6.1.4.1.1588.2.1.1.1.2.9

- swNbTable 1.3.6.1.4.1.1588.2.1.1.1.2.10

- swNbEntry 1.3.6.1.4.1.1588.2.1.1.1.2.10.1

- swNbIndex 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.1

- swNbMyPort 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.2

- swNbRemDomain 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.3

- swNbRemPort 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.4

- swNbBaudRate 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.5

- swNbIslState 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.6

- swNbIslCost 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.7

- swNbRemPortName 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.8

- swFabricMemTable 1.3.6.1.4.1.1588.2.1.1.1.2.11

- swFabricMemEntry 1.3.6.1.4.1.1588.2.1.1.1.2.11.1

- swFabricMemWwn 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.1

- swFabricMemDid 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.2

- swFabricMemName 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.3

- swFabricMemEIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.4

- swFabricMemFCIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.5

- swFabricMemGWIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.6

- swFabricMemType 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.7

- swFabricMemShortVersion 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.8

- swIDIDMode 1.3.6.1.4.1.1588.2.1.1.1.2.12

FIGURE 40

swFabric Hierarchy

- swModule (1.3.6.1.4.1.1588.2.1.1.1.3)

FIGURE 41

swModule Hierarchy

- swAgtCfg

- swAgtCmtyTable 1.3.6.1.4.1.1588.2.1.1.1.4.11

- swAgtCmtyEntry 1.3.6.1.4.1.1588.2.1.1.1.4.11.1

- swAgtCmtyIdx 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.1

- swAgtCmtyStr 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.2

- swAgtTrapRcp 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3

- swAgtTrapSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.4

FIGURE 42

swAgtCfg Hierarchy


53-1001156-01


53-1001156-01

SW MIB Overview

5

- swFCport (1.3.6.1.4.1.1588.2.1.1.1.6)

- swFCPortCapacity 1.3.6.1.4.1.1588.2.1.1.1.6.1

- swFCPortTable 1.3.6.1.4.1.1588.2.1.1.1.6.2

- swFCPortEntry 1.3.6.1.4.1.1588.2.1.1.1.6.2.1

- swFCPortIndex 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1

- swFCPortType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2

- swFCPortPhyState 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3

- swFCPortOpStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4

- swFCPortAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5

- swFCPortLinkState 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6

- swFCPortTxType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7

- swFCPortTxWords 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11

- swFCPortRxWords 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12

- swFCPortTxFrames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13

- swFCPortRxFrames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14

- swFCPortRxC2Frames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15

- swFCPortRxC3Frames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16

- swFCPortRxLCs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17

- swFCPortRxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18

- swFCPortTooManyRdys 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19

- swFCPortNoTxCredits 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20

- swFCPortRxEncInFrs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21

- swFCPortRxCrcs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22

- swFCPortRxTruncs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23

- swFCPortRxTooLongs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24

- swFCPortRxBadEofs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25

- swFCPortRxEncOutFrs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26

- swFCPortRxBadOs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27

- swFCPortC3Discards 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28

- swFCPortMcastTimedOuts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29

- swFCPortTxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30

- swFCPortLipIns 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31

- swFCPortLipOuts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32

- swFCPortLipLastAlpa 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33

- swFCPortWwn 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34

- swFCPortSpeed 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35

- swFCPortName 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36

- swFCPortSpecifier 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37

- swFCPortFlag 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38

- swFCPortBrcdType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39

FIGURE 43

swFCport Hierarchy

515

516

5

SW MIB Overview

- swNs

- swNsLocalNumEntry 1.3.6.1.4.1.1588.2.1.1.1.7.1

- swNsLocalTable 1.3.6.1.4.1.1588.2.1.1.1.7.2

- swNsLocalEntry 1.3.6.1.4.1.1588.2.1.1.1.7.2.1

- swNsEntryIndex 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1

- swNsPortID 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2

- swNsPortType 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.3

- swNsPortName 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.4

- swNsPortSymb 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.5

- swNsNodeName 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.6

- swNsNodeSymb 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.7

- swNsIPA 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.8

- swNsIpAddress 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.9

- swNsCos 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10

- swNsFc4 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.11

- swNsIpNxPort 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.12

- swNsWwn 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.13

- swNsHardAddr 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.14

FIGURE 44

swNs Hierarchy

- swEvent

- swEventTrapLevel 1.3.6.1.4.1.1588.2.1.1.1.8.1

- swEventNumEntries 1.3.6.1.4.1.1588.2.1.1.1.8.4

- swEventTable 1.3.6.1.4.1.1588.2.1.1.1.8.5

- swEventEntry 1.3.6.1.4.1.1588.2.1.1.1.8.5.1

- swEventIndex 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1

- swEventTimeInfo 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2

- swEventLevel 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3

- swEventRepeatCount 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4

- swEventDescr 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5

FIGURE 45

swEvent Hierarchy


53-1001156-01


53-1001156-01

SW MIB Overview

5

- swFwSystem

- swFwFabricWatchLicense 1.3.6.1.4.1.1588.2.1.1.1.10.1

- swFwClassAreaTable 1.3.6.1.4.1.1588.2.1.1.1.10.2

- swFwClassAreaEntry 1.3.6.1.4.1.1588.2.1.1.1.10.2.1

- swFwClassAreaIndex 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1

- swFwWriteThVals 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.2

- swFwDefaultUnit 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.3

- swFwDefaultTimebase 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.4

- swFwDefaultLow 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.5

- swFwDefaultHigh 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.6

- swFwDefaultBufSize 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.7

- swFwCustUnit 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.8

- swFwCustTimebase 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.9

- swFwCustLow 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.10

- swFwCustHigh 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.11

- swFwCustBufSize 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.12

- swFwThLevel 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.13

- swFwWriteActVals 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.14

- swFwDefaultChangedActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.15

- swFwDefaultExceededActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.16

- swFwDefaultBelowActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.17

- swFwDefaultAboveActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.18

- swFwDefaultInBetweenActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.19

- swFwCustChangedActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.20

- swFwCustExceededActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.21

- swFwCustBelowActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.22

- swFwCustAboveActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.23

- swFwCustInBetweenActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.24

- swFwValidActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.25

- swFwActLevel 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.26

- swFwThresholdTable 1.3.6.1.4.1.1588.2.1.1.1.10.3

- swFwThresholdEntry 1.3.6.1.4.1.1588.2.1.1.1.10.3.1

- swFwThresholdIndex 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1

- swFwStatus 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.2

- swFwName 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3

- swFwLabel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4

- swFwCurVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.5

- swFwLastEvent 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6

- swFwLastEventVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7

- swFwLastEventTime 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8

- swFwLastState 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9

- swFwBehaviorType 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.10

- swFwBehaviorInt 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.11

- swFwLastSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12

FIGURE 46

swFwSystem Hierarchy

517

518

5

SW MIB Overview

- swEndDevice

- swEndDeviceRlsTable 1.3.6.1.4.1.1588.2.1.1.1.21.1

- swEndDeviceRlsEntry 1.3.6.1.4.1.1588.2.1.1.1.21.1.1

- swEndDevicePort 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.1

- swEndDeviceAlpa 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.2

- swEndDevicePortID 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.3

- swEndDeviceLinkFailure 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.4

- swEndDeviceSyncLoss 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.5

- swEndDeviceSigLoss 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.6

- swEndDeviceProtoErr 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.7

- swEndDeviceInvalidWord 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.8

- swEndDeviceInvalidCRC 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.9

FIGURE 47

swEndDevice Hierarchy

- swGroup

- swGroupTable 1.3.6.1.4.1.1588.2.1.1.1.22.1

- swGroupEntry 1.3.6.1.4.1.1588.2.1.1.1.22.1.1

- swGroupIndex 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.1

- swGroupName 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.2

- swGroupType 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.3

- swGroupMemTable 1.3.6.1.4.1.1588.2.1.1.1.22.2

- swGroupMemEntry 1.3.6.1.4.1.1588.2.1.1.1.22.2.1

- swGroupID 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.1

- swGroupMemWwn 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.2

- swGroupMemPos 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.3

FIGURE 48

swGroup Hierarchy

- swBlmPerfMnt

- swBlmPerfALPAMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.1

- swBlmPerfALPAMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.1.1

- swBlmPerfAlpaPort 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.1

- swBlmPerfAlpaIndx 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.2

- swBlmPerfAlpa 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.3

- swBlmPerfAlpaCRCCnt 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.4

- swBlmPerfEEMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.2

- swBlmPerfEEMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.2.1

- swBlmPerfEEPort 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.1

- swBlmPerfEERefKey 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.2

- swBlmPerfEECRC 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.3

- swBlmPerfEEFCWRx 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.4

- swBlmPerfEEFCWTx 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.5

- swBlmPerfEESid 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.6

- swBlmPerfEEDid 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.7

- swBlmPerfFltMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.3

- swBlmPerfFltMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.3.1

- swBlmPerfFltPort 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.1

- swBlmPerfFltRefkey 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.2

- swBlmPerfFltCnt 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.3

- swBlmPerfFltAlias 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.4

FIGURE 49

swBlmPerfMnt Hierarchy


53-1001156-01

SW MIB Overview

5

- swTrunk

- swSwitchTrunkable 1.3.6.1.4.1.1588.2.1.1.1.24.1

- swTrunkTable 1.3.6.1.4.1.1588.2.1.1.1.24.2

- swTrunkEntry 1.3.6.1.4.1.1588.2.1.1.1.24.2.1

- swTrunkPortIndex 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.1

- swTrunkGroupNumber 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.2

- swTrunkMaster 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.3

- swPortTrunked 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.4

- swTrunkGrpTable 1.3.6.1.4.1.1588.2.1.1.1.24.3

- swTrunkGrpEntry 1.3.6.1.4.1.1588.2.1.1.1.24.3.1

- swTrunkGrpNumber 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.1

- swTrunkGrpMaster 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.2

- swTrunkGrpTx 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.3

- swTrunkGrpRx 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.4

FIGURE 50

swTrunk Hierarchy

- swTopTalker

- swTopTalkerMntMode 1.3.6.1.4.1.1588.2.1.1.1.25.1

- swTopTalkerMntNumEntries 1.3.6.1.4.1.1588.2.1.1.1.25.2

- swTopTalkerMntTable 1.3.6.1.4.1.1588.2.1.1.1.25.3

- swTopTalkerMntEntry 1.3.6.1.4.1.1588.2.1.1.1.25.3.1

- swTopTalkerMntIndex 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.1

- swTopTalkerMntPort 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.2

- swTopTalkerMntSpid 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.3

- swTopTalkerMntDpid 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.4

- swTopTalkerMntflow 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.5

FIGURE 51

swTopTalker Hierarchy

TABLE 12

SW-MIB Textual Conventions

Type Definition Value

FcWwn

SwDomainIndex

SwNbIndex

SwSensorIndex

SwPortIndex

Octet String of size 8

Integer of size 1 to 239



Integer32

SwTrunkMaster

Textual Conventions for SW-MIB

The following textual conventions are used for SW-MIB.

Integer32

Description

The World Wide Name (WWN) of Brocade-specific products and ports.

Fibre Channel domain ID of the switch.

Index of the neighbor inter-switch link (ISL) entry.

Index of the sensor entry.

Index of the port, starting from 1 up to the maximum number of ports on the Brocade switch.

Index of the trunk master, starting from 1 up to the maximum number of trunk groups on the Brocade switch.


53-1001156-01

519

5

SW MIB Overview

TABLE 12

SW-MIB Textual Conventions (Continued)

Type Definition

SwFwActs

SwFwLevels

Value

Integer

Integer

Description

Valid action matrix:

0 swFwNoAction

1 swFwErrlog

2 swFwSnmptrap

3 swFwErrlogSnmptrap

4 swFwPortloglock

5 swFwErrlogPortloglock

6 swFwSnmptrapPortloglock

7 swFwErrlogSnmptrapPortloglock

8 swFwRn

9 swFwElRn

10 swFwStRn

11 swFwElStRn

12 swFwPlRn

13 swFwElPlRn

14 swFwStPlRn

15 swFwElStPlRn

16 swFwMailAlert

17 swFwMailAlertErrlog

18 swFwMailAlertSnmptrap

19 swFwMailAlertErrlogSnmptrap

20 swFwMailAlertPortloglock

21 swFwMailAlertErrlogPortloglock

22 swFwMailAlertSnmptrapPortloglock

23 swFwMailAlertErrlogSnmptrapPortloglock

24 swFwMailAlertRn

25 swFwElMailAlertRn

26 swFwMailAlertStRn

27 swFwMailAlertElStRn

28 swFwMailAlertPlRn

29 swFwMailAlertElPlRn

30 swFwMailAlertStPlRn

31 swFwMailAlertElStPlRn

Threshold values or action matrix level:

1 swFwReserved

2 swFwDefault

3 swFwCustom


53-1001156-01

SW MIB Overview

5

TABLE 12


Type Definition

SwFwClassesAreas

Value

Integer

Description

Classes and area index:

1 swFwEnvTemp

2 swFwEnvFan

3 swFwEnvPs

4 swFwTransceiverTemp

5 swFwTransceiverRxp

6 swFwTransceiverTxp

7 swFwTransceiverCurrent

8 swFwPortLink

9 swFwPortSync

10 swFwPortSignal

11 swFwPortPe

12 swFwPortWords

13 swFwPortCrcs

14 swFwPortRXPerf

15 swFwPortTXPerf

16 swFwPortState

17 swFwFabricEd

18 swFwFabricFr

19 swFwFabricDi

20 swFwFabricSc

21 swFwFabricZc

23 swFwFabricFl

24 swFwFabricGs

25 swFwEPortLink

26 swFwEPortSync

27 swFwEPortSignal

28 swFwEPortPe

29 swFwEPortWords

30 swFwEPortCrcs

31 swFwEPortRXPerf

32 swFwEPortTXPerf

33 swFwEPortState

43 swFwFOPPortLink

44 swFwFOPPortSync

45 swFwFOPPortSignal

SwFwWriteVals

SwFwTimebase

SwFwStatus

Integer

Integer

Integer

46 swFwFOPPortPe

47 swFwFOPPortWords

48 swFwFOPPortCrcs

49 swFwFOPPortRXPerf

50 swFwFOPPortTXPerf

51 swFwFOPPortState

52 swFwPerfALPACRC

54 swFwPerfEToERxCnt

55 swFwPerfEToETxCnt

56 swFwPerffltCusDef

57 swFwTransceiverVoltage

58 swFwSecTelnetViolations

59 swFwSecHTTPViolations

60 swFwSecAPIViolations

61 swFwSecRSNMPViolations

62 swFwSecWSNMPViolations

63 swFwSecSESViolations

64 swFwSecMSViolations

65 swFwSecSerialViolations

66 swFwSecFPViolations

67 swFwSecSCCViolations

68 swFwSecDCCViolations

69 swFwSecLoginViolations

70 swFwSecInvaledTS

71 swFwSecInvalidSign

72 swFwSecInvalidCert

73 swFwSecSlapFail

74 swFwSecSlapBadPkt

75 swFwSecTSOutSync

76 swFwSecNoFcs

77 swFwSecIncompDB

78 swFwSecIllegalCmd

83 swFwResourceFlash

84 swFwEPortUtil

85 swFwEPortPktl

Write-only variable for applying or canceling values or action matrix changes:

1 swFwCancelWrite

2 swFwApplyWrite

Timebase for thresholds:

1 swFwTbNone

2 swFwTbSec

3 swFwTbMin

4 swFwTbHour

5 swFwTbDay

Status for thresholds:

1 disabled

2 enabled


53-1001156-01

521

5 sw Traps

TABLE 12


Type Definition

SwFwEvent

SwFwBehavior

SwFwState

SwFwLicense

Value

Integer

Integer

Integer

Integer

Description

Possible events available:

1 started

2 changed

3 exceeded

4 below

5 above

6 inBetween

Behavior type for thresholds:

1 triggered

2 continuous

State type for last events:

1 swFwInformative

2 swFwNormal

3 swFwfaulty

License state:

1 swFwLicensed

2 swFwNotLicensed

sw Traps

This section contains descriptions and other information that is specific to sw Traps.

From v6.2.0, the sw Traps will have an extra binding associated to indicate the Virtual Fabric (VF).

The following Traps will have VFID associated with them.

•

swTrackChangesTrap 1.3.6.1.4.1.1588.2.1.1.1.0.6

•

swFCPortScn 1.3.6.1.4.1.1588.2.1.1.1.0.3

•

swEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.4

•

swFabricWatchTrap 1.3.6.1.4.1.1588.2.1.1.1.0.5

•


•

FICON


53-1001156-01

sw Traps

5

Refer to Table 13

for the six traps defined in the SW.MIB, when it occurs, and how to configure the trap, if possible.

TABLE 13

SW MIB Traps

Name

“swFault

1.3.6.1.4.1.1588.2.1.1.1.0.1” on page 524

(not supported)

“swSensorScn

1.3.6.1.4.1.1588.2.1.1.1.0.2” on page 525

“swFCPortScn

1.3.6.1.4.1.1588.2.1.1.1.0.3” on page 526

“swEventTrap

1.3.6.1.4.1.1588.2.1.1.1.0.4” on page 527

“swFabricWatchTrap

1.3.6.1.4.1.1588.2.1.1.1.0.5” on page 528

“swTrackChangesTrap

1.3.6.1.4.1.1588.2.1.1.1.0.6” on page 529

Specific

1

2

3

4

5

6

When

During boot, if diagnostics fail

Obsolete

Port changes state

Switch event

Threshold reached

Log in/log out

Configure

N.A.

N.A.

Always on

Refer to the Fabric OS Command Reference and the snmpConfig command for more information.

Fabric OS Command: fwConfigure

Fabric OS Command: trackChangesSet and trackChangesShow

Refer to the Fabric OS Command Reference and the snmpMibCapSet command on how to enable or disable the sending of traps from the various MIBs.

The swSsn variable is optional in trap messages.

The swGroupName, swGroupType, and swGroupMemPos variables are optional trap messages in v2.6.x. The swGroupName, swGroupType, and swGroupMemPos variables are not supported in

Fabric OS v4.x and above.

Because Fabric OS releases prior to v5.2.0 used to show the Enterprise Field in the swTraps from the sysObjectID (set using config varaible "snmp.sysObjectID"), the Enterprise field will not always be resolved to "sw". If the sysObjectID is changed by user the Enterprise field in the trap will show some unresolved value.

To resolve this issue, beginning with the v5.2.0 release the SNMP configuration variable snmp.trapEnterpriseFlag lets you define the way that the Enterprise field appears.

Select either the previous behavior in which the Enterprise field is taken from sysObjectID or the new behavior in which the value in the Enterprise field will alway be "sw".

•

Set the value of this variable to 0, to use the sysObjectID .

•

Set the value to 1 to use the fixed enterprise value, "sw" (1.3.6.1.4.1.1588.2.1.1.1.) .


53-1001156-01

523

5 swFault 1.3.6.1.4.1.1588.2.1.1.1.0.1

swFault 1.3.6.1.4.1.1588.2.1.1.1.0.1

Enterprise

Variables

This trap is no longer generated.

sw

“swDiagResult 1.3.6.1.4.1.1588.2.1.1.1.1.20”

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

A swFault is generated whenever the diagnostics detect a fault with the switch.

#TYPE

#SUMMARY

#ARGUMENTS

#SEVERITY

#TIMEINDEX

#STATE

Switch is faulty.

Faulty reason: %d and SSN is #%s

0, 1

Critical

1

Nonoperational


53-1001156-01

swSensorScn 1.3.6.1.4.1.1588.2.1.1.1.0.2

5 swSensorScn 1.3.6.1.4.1.1588.2.1.1.1.0.2

Enterprise

Variables

(Obsoleted by swFabricWatchTrap) sw

“swSensorStatus 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3”

“swSensorIndex 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1”

“swSensorType 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2”

“swSensorValue 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4”

“swSensorInfo 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5”

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

A swSensorScn (2) is generated whenever an environment sensor changes its operational state: for instance, if a fan stop working. The VarBind in the Trap Data Unit contain the corresponding instance of the sensor status, sensor index, sensor type, sensor value (reading), and sensor information. Note that the sensor information contains the type of sensor and its number, in textual format.

#TYPE

#SUMMARY

#ARGUMENTS

#SEVERITY

#TIMEINDEX

#STATE

A sensor (temperature, fan, or other) changed its operational state.

%s: is currently in state %d and SSN is #%s

4, 0, 5

Informational

1

Operational


53-1001156-01

525

5 swFCPortScn 1.3.6.1.4.1.1588.2.1.1.1.0.3

swFCPortScn 1.3.6.1.4.1.1588.2.1.1.1.0.3

Enterprise

Variables sw

“swFCPortOpStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4”

“swFCPortIndex 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1”

“swFCPortName 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36”

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

“swFCPortFlag 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38”

A swFCPortScn (3) is generated whenever an FC_Port changes its operational state: for instance, the FC_Port goes from online to offline. The VarBind in the Trap Data Unit contain the corresponding instance of the FC_Port's operational status, index, swFCPortName, and swSsn. swFCPortName and swSsn are optional.

#TYPE

#SUMMARY

#ARGUMENTS

#SEVERITY

#TIMEINDEX

#STATE

A Fibre Channel Port changed its operational state.

Port Index %d changed state to %d. Port Name: %s and

SSN is #%s

1, 0, 2, 3

Informational

1

Operational

Sample trap output for Fabric OS 4.4.0: swFCPortOpStatus.11 = offline(2) swFCPortIndex.11 = 11 swFCPortName.11 = test swSsn.0 = none


53-1001156-01

swEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.4

5 swEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.4

Enterprise

Variables sw

“swEventIndex 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1”

“swEventTimeInfo 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2”

“swEventLevel 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3”

“swEventRepeatCount 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4”

“swEventDescr 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5”

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

This trap is generated when an event occurs with a level that is at or below “swEventTrapLevel

1.3.6.1.4.1.1588.2.1.1.1.8.1” .

#TYPE

#SUMMARY

#ARGUMENTS

#SEVERITY

#TIMEINDEX

#STATE

A firmware event has been logged.

Event %d: %s (severity level %d) - %s SSN is #%s

0, 1, 2, 4, 5

Informational

1

Operational

Each Trap recipient has a configured severity level association. Whenever an error message is generated at or above that configured severity level the recipient is notified of the event.

This trap is generated for all RASLog messages. From Fabric OS 4.4.0 this trap is only generated for external RASLog messages.

Sample trap output for Fabric OS 4.4.0: swEventIndex.39 = 39 swEventTimeInfo.39 = 2004/08/10-07:00:17 swEventLevel.39 = warning (3) swEventRepeatCount.39 = 1 swEventDescr.39 = SULB-1001 Firmwaredownload command has started. swSsn.0 = none

To get more details on any particular event, refer to the Fabric OS Message Reference.


53-1001156-01

527

5 swFabricWatchTrap 1.3.6.1.4.1.1588.2.1.1.1.0.5


Enterprise

Variables sw

“swFwClassAreaIndex 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1”

“swFwThresholdIndex 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1”

“swFwName 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3”

“swFwLabel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4”

“swFwLastEvent 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6”

“swFwLastEventVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7”

“swFwLastEventTime 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8”

“swFwLastState 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9”

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

“swFwLastSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12”

Trap to be sent by Fabric Watch to notify of an event.

#TYPE

#SUMMARY

#ARGUMENTS

#SEVERITY

#TIMEINDEX

#STATE

Fabric Watch has generated an event.

Threshold %s in Class/Area %d at index %d has generated event %d with %d on %s. This event is %d and SSN is #%s

2, 0, 1, 6, 4, 5, 7, 8

Warning

1

Operational

Refer to the Fabric Watch Administrator’s Guide for information on setting thresholds in Fabric

Watch.

Sample trap output for Fabric OS 4.4.0: swFwClassAreaIndex.1 = swFwEnvTemp(1) swFwThresholdIndex.1.2 = 2 swFwName.1.2 = envTemp001 swFwLabel.1.2 = Env Temperature 1 swFwLastEventVal.1.2 = 45 swFwLastEventTime.1.2 = 06:17:01 on 08/12/2004 swFwLastEvent.1.2 = inBetween(6) swFwLastState.1.2 = swFwNormal(2) swFwLastSeverityLevel.1.2 = 4 swSsn.0 = none


53-1001156-01

swTrackChangesTrap 1.3.6.1.4.1.1588.2.1.1.1.0.6

5 swTrackChangesTrap 1.3.6.1.4.1.1588.2.1.1.1.0.6

Enterprise

Variables sw

“swTrackChangesInfo 1.3.6.1.4.1.1588.2.1.1.1.1.23”

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

Trap to be sent for tracking log in/log out/configuration changes.

#TYPE

#SUMMARY

#ARGUMENTS

#SEVERITY

#TIMEINDEX

#STATE

Track changes has generated a trap.

%s and SSN is #%s

0, 1

Informational

1

Operational

Some of the triggers that will generate this trap are:

•

Log out

•

Unsuccessful log in

•

Successful log in

•

Switch configuration changes

•

Track changes on and off

Sample trap output for Fabric OS 4.4.0: swTrackChangesInfo.0 = Logout swSsn.0 = none

This trap gets sent when track-changes is set to ENABLED and is configured to send SNMP traps on track events. Use the trackchangesset command to enable the track changes feature and SNMP trap mode.


53-1001156-01

529

5 swIPv6ChangeTrap 1.3.6.1.4.1.1588.2.1.1.1.0.7

swIPv6ChangeTrap 1.3.6.1.4.1.1588.2.1.1.1.0.7

Enterprise

Variables sw

“swIPv6Address 1.3.6.1.4.1.1588.2.1.1.1.1.29”

“swIPv6Status 1.3.6.1.4.1.1588.2.1.1.1.1.30”

This trap is generated when an IPv6 address status change event occurs.


53-1001156-01

swPmgrEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.8

5 swPmgrEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.8

Enterprise

Variables sw

“swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10”

“swVfId 1.3.6.1.4.1.1588.2.1.1.1.2.9”

This trap is generated when any partition manager change happens.


53-1001156-01

531

5 swSystem Group

swSystem Group

swCurrentDate 1.3.6.1.4.1.1588.2.1.1.1.1.1

The current date and time.

The return string displays using the following format: ddd MMM DD hh:mm:ss yyyy

Where: ddd = day

MMM = month

DD = date hh = hour mm = minute ss = seconds yyyy = year

For example:

Thu Aug 17 15:16:09 2000


53-1001156-01

swBootDate 1.3.6.1.4.1.1588.2.1.1.1.1.2

5 swBootDate 1.3.6.1.4.1.1588.2.1.1.1.1.2

The date and time when the system last booted.


Where: ddd = day

MMM = month


For example:

Thu Aug 17 15:16:09 2000


53-1001156-01

533

5 swFWLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.3

swFWLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.3

The date and time when the firmware was last loaded to the switch.


Where: ddd = day

MMM = month


For example:

Thu Aug 17 15:16:09 2000


53-1001156-01

swFlashLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.4

5 swFlashLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.4

The date and time when the firmware was last downloaded or the configuration file was last changed.


Where: ddd = day

MMM = month


For example:

Thu Aug 17 15:16:09 2000


53-1001156-01

535

5 swBootPromLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.5

swBootPromLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.5

The date and time when the BootPROM was last updated.


Where: ddd = day

MMM = month


For example:

Thu Aug 17 15:16:09 2000


53-1001156-01

swFirmwareVersion 1.3.6.1.4.1.1588.2.1.1.1.1.6

5 swFirmwareVersion 1.3.6.1.4.1.1588.2.1.1.1.1.6

The current version of the firmware.

The return value is displayed using the following format: vM.m.f

Where: v

= deployment indicator

M

= major version m

= minor version f

= software maintenance version

For example, v6.1.0_main_bld36 described firmware version 6.1.0 and the specific build number

36. Some versions may not have a build number and will appear as the version. An example might be v6.1.0 indicates Fabric OS version 6.0.0.


53-1001156-01

537

5 swOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.7

swOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.7

Values

The current operational status of the switch.


• online (1) The switch is accessible by an external Fibre Channel port.

• offline (2) The switch is not accessible.

• testing (3) The switch is in a built-in test mode and is not accessible by an external Fibre

Channel port.

• faulty (4) The switch is not operational.


53-1001156-01

swAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.8

5 swAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.8

Values

The desired administrative status of the switch. A management station might place the switch in a desired state by setting this object accordingly.


• online (1) Set the switch to be accessible by an external FC port.

• offline (2) Set the switch to be inaccessible.

• testing (3) Set the switch to run the built-in test.

• faulty (4) Set the switch to a “soft” faulty condition.

• reboot (5) Set the chassis to reboot in 1 second.

• fastboot (6) Set the chassis to fastboot in 1 second. Fastboot causes the chassis to boot but omit the POST.

When the switch is in faulty state, only two states can be set: faulty and reboot/fastboot

For the Brocade 3250, 3850, 3900, 24000, 48000, DCX, and DCX-4S director the testing (3) and faulty (4) values are not applicable.

The Possibles values for Brocade 300, 5100 and 5300 are either online(1) and offline(2).


53-1001156-01

539

5 swTelnetShellAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.9

swTelnetShellAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.9

Values

The desired administrative status of the telnet shell.

Setting this value to 1 (terminated), deletes the current telnet shell task. When this variable instance is read, it reports the value last set through SNMP.

This OID is supported in Fabric OS v2.x through v3.x.

This OID is not supported in Fabric OS v4.0 through v4.2.

It is supported in Fabric OS version 4.3 and above.


• unknown (0) The status of the current telnet shell task is unknown.

• terminated (1) The current telnet shell task is deleted.

By setting it to 1 (terminated), the current telnet shell task is deleted. When this variable instance is read, it reports the value last set through SNMP.


53-1001156-01

swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10

5 swSsn 1.3.6.1.4.1.1588.2.1.1.1.1.10

The soft serial number of the switch.

This variable will return the “ssn” value that is stored in the config database. If the “ssn” key value pair is not in the config database it will return WWN of the switch.”

Flash Administration

The next six objects are related to firmware or configuration file management. Due to security restrictions, firmwaredownload and configuration file upload and download are no longer supported through SNMP, in Fabric OS v4.4 and above.


53-1001156-01

541

5 swFlashDLOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.11

swFlashDLOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.11

The operational status of the flash.

This OID cannot be used for either Firmwaredownload or Configdownload (cannot be set and is readonly) for Fabric OS v4.4 and above. The value displayed is always "swCurrent(1)".


53-1001156-01

swFlashDLAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.12

5 swFlashDLAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.12

Values

The desired state of the flash.

The host is specified in swFlashDLHost.0. In addition, the user name is specified in swFlashDLUser.0 and the file name specified in swFlashDLFile.0.

This OID is writeable only in Fabric OS v2.6.x and v3.x.

This OID cannot be used for either firmwareDownload or configDownload (cannot be set and is readonly) for Fabric OS v4.4 and above. The value displayed is always "swCurrent(1)".This is not supported in v6.0.0 and higher versions.


• swCurrent (1) The flash contains the current firmware image or configuration file.

• swCfUpload (3) The switch configuration file is to be uploaded to the host specified.

• swCfDownload (4) The switch configuration file is to be downloaded from the host specified.

• swFwCorrupted (5) The firmware in the flash is corrupted. This value is for informational purposes only; however, setting swFlashDLAdmStatus to this value is not allowed.

For more information about the firmwareDownload, configDownload and configUpload commands, refer to the Fabric OS Command Reference.


53-1001156-01

543

5 swFlashDLHost 1.3.6.1.4.1.1588.2.1.1.1.1.13

swFlashDLHost 1.3.6.1.4.1.1588.2.1.1.1.1.13

The name or IP address (in dot notation) of the host to download or upload a relevant file to the flash.

This OID cannot be used for either firmwareDownload or configDownload (cannot be set and is readonly) for Fabric OS v4.4 and above. The value displayed is always NULL (zero-length).This is not supported in v6.0.0 and higher versions.


53-1001156-01

swFlashDLUser 1.3.6.1.4.1.1588.2.1.1.1.1.14

5 swFlashDLUser 1.3.6.1.4.1.1588.2.1.1.1.1.14

The user name is used on the host for downloading or uploading a relevant file, to or from the flash.



53-1001156-01

545

5 swFlashDLFile 1.3.6.1.4.1.1588.2.1.1.1.1.15

swFlashDLFile 1.3.6.1.4.1.1588.2.1.1.1.1.15

The name of the file to be downloaded or uploaded.



53-1001156-01

swFlashDLPassword 1.3.6.1.4.1.1588.2.1.1.1.1.16

5 swFlashDLPassword 1.3.6.1.4.1.1588.2.1.1.1.1.16

The password to be used for FTP transfer of files in the download or upload operation.



53-1001156-01

547

5 swBeaconOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.18

swBeaconOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.18

Values

The current operational status of the switch beacon.


• on (1) The LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow.

• off (2) Each LED is in its regular status, indicating color and state.


53-1001156-01

swBeaconAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.19

5 swBeaconAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.19

Values

The desired status of the switch beacon.


• on (1) The LEDs on the front panel of the switch run alternately from left to right and right to left. Set the color to yellow.

• off (2) Set each LED to its regular status, indicating color and state.


53-1001156-01

549

5 swDiagResult 1.3.6.1.4.1.1588.2.1.1.1.1.20

swDiagResult 1.3.6.1.4.1.1588.2.1.1.1.1.20

Values

The result of the power-on startup test (POST) diagnostics.


• sw-ok (1) The switch is okay.

• sw-faulty (2) The switch has experienced an unknown fault.

• sw-embedded-port-fault (3) The switch has experienced an embedded port fault.


53-1001156-01

swNumSensors 1.3.6.1.4.1.1588.2.1.1.1.1.21

5 swNumSensors 1.3.6.1.4.1.1588.2.1.1.1.1.21

The number of sensors inside the switch.

The Brocade DCX value is between 1 and 57 (temperature =50, fan = 3, power supply = 4). The value might vary depending on the switch model. For Fabric OS v6.1.0, if no sensor is available, this variable is assigned the value -1.


53-1001156-01

551

5 swSensorTable 1.3.6.1.4.1.1588.2.1.1.1.1.22

swSensorTable 1.3.6.1.4.1.1588.2.1.1.1.1.22

Table of sensor entries.

TABLE 14

Sensors on the Various Brocade Switches

Platform Temp Fans Power Supply

Brocade 200E

Brocade 3016

Brocade 3200

Brocade 3250

Brocade 3800

Brocade 3850

Brocade 3900

Brocade 4012

Brocade 4100

Brocade 4900

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000

Brocade 24000

Brocade 48000

Brocade DCX

Brocade DCX-4S

Brocade 300

Brocade 5100

Brocade 5300

2 sensors

4 sensors

3 sensors

2 absent

4 sensors

3 sensors

2 absent

4 sensors

5 sensors

2 sensors

5 sensors

3 sensors sensors

3 sensors

3 sensors

10 sensors

10 sensors

10 sensors

50 sensors

30 sensors

3 sensors

4 sensors

3 sensors

3 fans

3 fans

2 fans

3 fans

2 fans

3 fans

NA

3 fans

3 fans

3 fans

3 fans

3 fans

3 fans

3 fans

3 fans

NA

5 fans

1 absent

3 fans

4 fans

2 absent

4 fans

6 fans

4 PS

4 PS

2 PS

1 PS

2 PS

2 PS

2 PS

2 PS

4 PS

4 PS

2 PS

2 PS

NA

2 PS

2 PS

2 PS

1 PS

NA

2 absent

1 PS

2 PS

8

8

17

57

35

7

18

18

17

17 swNumSensors / connUnitNumSensors

2

10

18

6

4

13

Note: Shows absent entries.

8

13

Note: Shows absent entries.

10

13


53-1001156-01

swSensorEntry 1.3.6.1.4.1.1588.2.1.1.1.1.22.1

5 swSensorEntry 1.3.6.1.4.1.1588.2.1.1.1.1.22.1

Index

An entry of the sensor information.

swSensorIndex


53-1001156-01

553

5 swSensorIndex 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1

swSensorIndex 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1

The index of the sensor.

The values are 1 through the value in swNumSensors.


53-1001156-01

swSensorType 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2

5 swSensorType 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2

The type of sensor.


53-1001156-01

555

5 swSensorStatus 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3

swSensorStatus 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3

Values

The current status of the sensor.


•

1: unknown (1)

•

2: faulty (2)

•

3: below-min (3) The sensor value is below the minimal threshold.

•

4: nominal (4)

•

5: above-max (5) The sensor value is above the maximum threshold.

•

6: absent (6) The sensor is missing.

For Temperature, valid values include 3 (below-min), 4 (nominal), and 5 (above-max).

For Fan, valid values include 3 (below-min), 4 (nominal), and 6 (absent).

For Power Supply, valid values include 2 (faulty), 4 (nominal), and 6 (absent).


53-1001156-01

swSensorValue 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4

5 swSensorValue 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4

The current value (reading) of the sensor.

The value -2147483648 represents the maximum value of integer value; it also means that the sensor does not have the capability to measure the actual value. In v2.0, the temperature sensor value is in Celsius, the fan value is in RPM (revolutions per minute), and the power supply sensor reading is unknown.

The unknown value -2147483648 indicates the maximum value of integer value.


53-1001156-01

557

5 swSensorInfo 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5

swSensorInfo 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5

Additional information on the sensor. It contains the sensor type and number, in textual format; for example:

SLOT #0: TEMP #3

FAN #1

Power Supply #1

Return values for the Brocade 12000, 24000, and 48000 directors depend upon the configuration of your system.


53-1001156-01

swTrackChangesInfo 1.3.6.1.4.1.1588.2.1.1.1.1.23

5 swTrackChangesInfo 1.3.6.1.4.1.1588.2.1.1.1.1.23

Track changes string; for trap only.

If there are no events to track, the default return value is “No event so far.”

If there are events to track, the following are valid return values:

•

Successful log in

•

Unsuccessful log in

•

Logout

•

Configuration file change from task [name of task]

•

Track-changes on

•

Track-changes off


53-1001156-01

559

5 swID 1.3.6.1.4.1.1588.2.1.1.1.1.24

swID 1.3.6.1.4.1.1588.2.1.1.1.1.24

Not supported in Fabric OS v3.2.0.

With VF enabled fabric the number of logical switch will be 0 to 128.


53-1001156-01

swEtherIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.25

5 swEtherIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.25

Not supported in Fabric OS v3.2.0. Supported in Fabric OS v6.2.0

The IP address of the Ethernet interface of this logical switch.


53-1001156-01

561

5 swEtherIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.26

swEtherIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.26


The IP mask of the Ethernet interface of this logical switch.


53-1001156-01

swFCIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.27

5 swFCIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.27


The IP address of the FC interface of this logical switch.


53-1001156-01

563

5 swFCIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.28

swFCIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.28


The IP mask of the FC interface of this logical switch.


53-1001156-01

swIPv6Address 1.3.6.1.4.1.1588.2.1.1.1.1.29

5 swIPv6Address 1.3.6.1.4.1.1588.2.1.1.1.1.29

The IPv6 address.


53-1001156-01

565

5 swIPv6Status 1.3.6.1.4.1.1588.2.1.1.1.1.30

swIPv6Status 1.3.6.1.4.1.1588.2.1.1.1.1.30

The current status of the IPv6 address.


53-1001156-01

swModel 1.3.6.1.4.1.1588.2.1.1.1.1.31

Indicates whether the switch is 7500 or 7500E.

swModel 1.3.6.1.4.1.1588.2.1.1.1.1.31

5


53-1001156-01

567

5 swFabric Group

swFabric Group

swDomainID 1.3.6.1.4.1.1588.2.1.1.1.2.1

The current Fibre Channel domain ID of the switch. To set a new value, the switch (swAdmStatus) must be in offline or testing state.


53-1001156-01

swPrincipalSwitch 1.3.6.1.4.1.1588.2.1.1.1.2.2

5 swPrincipalSwitch 1.3.6.1.4.1.1588.2.1.1.1.2.2

Values

Indicates whether the switch is the principal switch.


• yes (1)

• no (2)


53-1001156-01

569

5 swNumNbs 1.3.6.1.4.1.1588.2.1.1.1.2.8

swNumNbs 1.3.6.1.4.1.1588.2.1.1.1.2.8

The number of inter-switch links (ISLs) in the (immediate) neighborhood.


53-1001156-01

swVfId 1.3.6.1.4.1.1588.2.1.1.1.2.9

The VFID of the switch.

swVfId 1.3.6.1.4.1.1588.2.1.1.1.2.9

5


53-1001156-01

571

5 swNbTable 1.3.6.1.4.1.1588.2.1.1.1.2.10

swNbTable 1.3.6.1.4.1.1588.2.1.1.1.2.10

This table contains the ISLs in the immediate neighborhood of the switch.


53-1001156-01

swNbEntry 1.3.6.1.4.1.1588.2.1.1.1.2.10.1

5 swNbEntry 1.3.6.1.4.1.1588.2.1.1.1.2.10.1

Index

An entry containing each neighbor ISL parameters.

swNbIndex


53-1001156-01

573

5 swNbIndex 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.1

swNbIndex 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.1

The index for neighborhood entry.


53-1001156-01

swNbMyPort 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.2

5 swNbMyPort 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.2

This is the port that has an ISL to another switch.

This value is the same as the physical port number of the local switch +1. The valid values for the

Brocade 12000, 24000, and 48000 directors are 1 through the maximum number of ports +1.


53-1001156-01

575

5 swNbRemDomain 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.3

swNbRemDomain 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.3

This is the Fibre Channel domain on the other end of the ISL.

This is the domain ID of the remote switch.Valid values are 1 through 239 as defined by FCS-SW.


53-1001156-01

swNbRemPort 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.4

5 swNbRemPort 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.4

This is the port index on the other end of the ISL.

The physical port number of the remote switch, plus 1. The valid values for the Brocade 12000,

24000, and 48000 directors are 1 through the maximum number of ports +1.


53-1001156-01

577

5 swNbBaudRate 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.5

swNbBaudRate 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.5

Values

The baud rate of the ISL. It is always unknown (0).


• other (1) None of the following.

• oneEighth (2) 155 Mbaud.

• quarter (4) 266 Mbaud.

• half (8) 532 Mbaud.

• full (16) 1 Gbaud.

• double (32) 2 Gbaud.

• quadruple (64) 4 Gbaud.

• octuple(128) 8 Gbaud.

• decuple(256) 10 Gbaud.

The valid values for the Brocade 12000, 24000, and 48000 directors switch are 16 (full) and 32

(double).

The valid value for the Brocade 4100 is 64 (quadruple).

The valid values for the Brocade DCX are double(32), quadruple(64), and octuple(128).


53-1001156-01

swNbIslState 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.6

5 swNbIslState 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.6

The current state of the ISL. The possible values are as follwos.

0 - ISL is down.

1 - ISL is initiating and not yet operational.

2, 3, 4, - used for notification of internal states.

5 - ISL is active.


53-1001156-01

579

5 swNbIslCost 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.7

swNbIslCost 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.7

The current link cost of the ISL. In other words, the cost of a link to control the routing algorithm.


53-1001156-01

swNbRemPortName 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.8

5 swNbRemPortName 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.8

The WWN of the remote port.


53-1001156-01

581

5 swFabricMemTable 1.3.6.1.4.1.1588.2.1.1.1.2.11

swFabricMemTable 1.3.6.1.4.1.1588.2.1.1.1.2.11

Supported in Fabric OS v2.6.1 and not v3.2.0.

This table contains information on the member switches of a fabric. This might not be available on all versions of Fabric OS. This is not available in v6.2.0.


53-1001156-01

swFabricMemEntry 1.3.6.1.4.1.1588.2.1.1.1.2.11.1

5 swFabricMemEntry 1.3.6.1.4.1.1588.2.1.1.1.2.11.1

Index

An entry containing each switch in the fabric.

swFabricMemWwn


53-1001156-01

583

5 swFabricMemWwn 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.1

swFabricMemWwn 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.1

This object identifies the World Wide Name of the member switch.


53-1001156-01

swFabricMemDid 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.2

5 swFabricMemDid 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.2

This object identifies the domain ID of the member switch.


53-1001156-01

585

5 swFabricMemName 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.3

swFabricMemName 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.3

This object identifies the name of the member switch.


53-1001156-01

swFabricMemEIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.4

5 swFabricMemEIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.4

This object identifies the Ethernet IP address of the member switch.


53-1001156-01

587

5 swFabricMemFCIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.5

swFabricMemFCIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.5

This object identifies the Fibre Channel IP address of the member switch.


53-1001156-01

swFabricMemGWIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.6

5 swFabricMemGWIP 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.6

This object identifies the Gateway IP address of the member switch.


53-1001156-01

589

5 swFabricMemType 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.7

swFabricMemType 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.7

This object identifies the member switch type.


53-1001156-01

swFabricMemShortVersion 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.8

5 swFabricMemShortVersion 1.3.6.1.4.1.1588.2.1.1.1.2.11.1.8

This object identifies the Fabric OS version of the member switch.

Provides the short version of the Fabric OS version number.


53-1001156-01

591

5 swIDIDMode 1.3.6.1.4.1.1588.2.1.1.1.2.12

swIDIDMode 1.3.6.1.4.1.1588.2.1.1.1.2.12

This identifies the status of Insistent Domain ID (IDID) mode. Status indicating if IDID mode is enabled or not.


53-1001156-01

SW Agent Configuration Group

SW Agent Configuration Group

swAgtCmtyTable 1.3.6.1.4.1.1588.2.1.1.1.4.11

A table that contains, one entry for each community, the access control and parameters of the community.

The table displays all of the community strings (read and write) if it is accessed by the “write” community string. Only “read” community strings are displayed if it is accessed by the “read” community string.

In Secure Fabric OS, the community strings can only be modified on the primary switch.

5


53-1001156-01

593

5 swAgtCmtyEntry 1.3.6.1.4.1.1588.2.1.1.1.4.11.1

swAgtCmtyEntry 1.3.6.1.4.1.1588.2.1.1.1.4.11.1

Index

An entry containing the community parameters.

swAgtCmtyIdx


53-1001156-01

swAgtCmtyIdx 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.1

5 swAgtCmtyIdx 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.1

The SNMPv1 community entry.

The return value for this entry is 1 through 6.


53-1001156-01

595

5 swAgtCmtyStr 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.2

swAgtCmtyStr 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.2

This is a community string supported by the agent. If a new value is set successfully, it takes effect immediately.

Default values for communities are as follows:

•

1 (Secret Code)

•

2 (OrigEquipMfr)

•

3 (private)

•

4 (public)

•

5 (common)

•

6 (FibreChannel)

Community strings 1-3 are read-write and strings 4-6 are read-only.

You can change the community setting using the snmpconfig command.


53-1001156-01

swAgtTrapRcp 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3

5 swAgtTrapRcp 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3

This is the trap recipient associated with the community. If a new value is set successfully, it takes effect immediately.

If not otherwise set, the default IP address for this trap recipient is 0.0.0.0 and the SNMP trap is not sent for the associated community string.

With a setting of non-0.0.0.0 IP address, SNMP traps are sent to the host with the associated community string.

Any or all of the trap recipients can be configured to send a trap for the associated community string. The maximum number of trap recipients that can be configured is six. If no trap recipient is configured, no traps are sent.

The trap recipient IP address should be part of the Access Control List for Fabric OS v2.6.1, v3.1, and v4.x (Refer to the Fabric OS Command Reference and the snmpConfig command for more information).


53-1001156-01

597

5 swAgtTrapSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.4

swAgtTrapSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.4

This is the trap severity level associated with

swAgtTrapRcp 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3

. The

trap severity level, is in conjunction with the event’s severity level. When an event occurs, and if its severity level is at or below the set value, the SNMP trap is sent to configure trap recipients. The severity level is limited to particular events. If a new value is set successfully, it takes effect immediately.

This object obsoletes

swEventTrapLevel 1.3.6.1.4.1.1588.2.1.1.1.8.1

.

Fibre Channel Port Group

This group contains information about the physical state, operational status, performance, and error statistics of each Fibre Channel port on the switch. A Fibre Channel port is one which supports the Fibre Channel protocol, such as F_Port, E_Port, U_Port, or FL_Port.


53-1001156-01

swFCPortCapacity 1.3.6.1.4.1.1588.2.1.1.1.6.1

5 swFCPortCapacity 1.3.6.1.4.1.1588.2.1.1.1.6.1

Values

The maximum number of Fibre Channel ports on this switch. It includes U_Port, F_Port, FL_Port, and any other types of Fibre Channel port.

The valid values are as follows:

Brocade 3200, 3250

Brocade 4012

Brocade 200E, 3800, 3850

Brocade 3900, 4100

Brocade 4900

Brocade 7500

Brocade 7600

Brocade 12000

8 ports

12 ports

16 ports

32 ports

64 ports

16 ports

16 ports

64 ports (per logical switch)

Brocade 24000 (2 logical switches64 ports (per logical switch)

Brocade 24000 (1 logical switch) 128 ports

Brocade 48000 448 ports

Brocade DCX

Brocade DCX-4S

Brocade 300

Brocade 5100

Brocade 5300

Brocade Encryption Switch

384 ports

192 ports

40 ports

80 ports

24 ports

32 ports


53-1001156-01

599

5 swFCPortFlag 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38

swFCPortFlag 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38

Index

A bit map of port status flags that includes the information of port type. Indicates whether the port is virtual or physical.

swFCPortEntry


53-1001156-01

swFCPortTable 1.3.6.1.4.1.1588.2.1.1.1.6.2

5 swFCPortTable 1.3.6.1.4.1.1588.2.1.1.1.6.2

A table that contains one entry for each switch port, configuration and service parameters of the port.


53-1001156-01

601

5 swFCPortEntry 1.3.6.1.4.1.1588.2.1.1.1.6.2.1

swFCPortEntry 1.3.6.1.4.1.1588.2.1.1.1.6.2.1

Index

An entry containing the configuration and service parameters of the switch port.

swFCPortIndex


53-1001156-01

swFCPortIndex 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1

swFCPortIndex 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1

Values

The switch port index.

The physical port number of the switch, plus 1.

The valid values for the Brocade 12000, 24000, and 48000 directors are 0 through maximum

number of ports.

5


53-1001156-01

603

5 swFCPortType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2

swFCPortType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2

Values

The type of ASIC for the switch port.


• stitch (1)

• flannel (2)

• loom (3) (Brocade 2000 series)

• bloom (4) (Valid value for Brocade 3250, 3850, 3900, 12000, 24000)

• rdbloom (5)

• wormhole (6)

• other (7) (Valid value for Brocade 200E, 4012, 4100, 4900, 7500, 7600, 48000, 300, 5100 and 5300)

• unknown (8)


53-1001156-01

swFCPortPhyState 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3

5 swFCPortPhyState 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3

Values

The physical state of the port.


• noCard (1) No card is present in this switch slot.

• noTransceiver (2) No Transceiver module in this port (Transceiver is the generic name for GBIC,

SFP, and so on).

• laserFault (3) The module is signaling a laser fault (defective GBIC).

• noLight (4) The module is not receiving light.

• noSync (5) The module is receiving light but is out of sync.

• inSync (6) The module is receiving light and is in sync.

• portFault (7) The port is marked faulty (defective GBIC, cable, or device).

• diagFault (8) The port failed diagnostics (defective G_Port or FL_Port card or motherboard).

• lockRef (9) Port is locking to the reference signal.


53-1001156-01

605

5 swFCPortOpStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4

swFCPortOpStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4

Values

The operational status of the port.


• unknown (0) The port module is physically absent.

• online (1) User frames can be passed.

• offline (2) No user frames can be passed.

• testing (3) No user frames can be passed.

• faulty (4) The port module is physically faulty.


53-1001156-01

swFCPortAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5

5 swFCPortAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5

Values

The desired state of the port. A management station might place the port in a desired state by setting this object accordingly.


• online (1) User frames can be passed.

• offline (2) No user frames can be passed.

• testing (3) No user frames can be passed.

• faulty (4) No user frames can be passed.

For Fabric OS v3.x:

The 3 (testing) state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, swFCPortAdmStatus is then changed to either the 1 (online) or 3 (testing) states or remains in the 2 (offline) state.

For Fabric OS v4.x:

The 3 (testing) state is not supported.


53-1001156-01

607

5 swFCPortLinkState 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6

swFCPortLinkState 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6

Values

Indicates the link state of the port. When the port's link state changes, its operational status

(swFCPortOpStatus) is affected.


• enabled (1) The port is allowed to participate in the FC-PH protocol with its attached port (or ports if it is in an FC-AL loop).

• disabled (2) The port is not allowed to participate in the FC-PH protocol with its attached ports.

• loopback (3) The port might transmit frames through an internal path to verify the health of the transmitter and receiver path.


53-1001156-01

swFCPortTxType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7

5 swFCPortTxType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7

Values

Indicates the media transmitter type of the port.


• unknown (1) Cannot determine the port driver.

• lw (2) Long wave laser.

• sw (3) Short wave laser.

• ld (4) Long wave LED.

• cu (5) Copper (electrical).


53-1001156-01

609

5 swFCPortTxWords 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11

swFCPortTxWords 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11

Counts the number of Fibre Channel words that the port has transmitted. You can convert words to bytes by multiplying this value by 4.


53-1001156-01

swFCPortRxWords 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12

5 swFCPortRxWords 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12

Counts the number of Fibre Channel words that the port has received.

You can convert words to bytes by multiplying this value by 4.


53-1001156-01

611

5 swFCPortTxFrames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13

swFCPortTxFrames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13

Counts the number of Fibre Channel frames that the port has transmitted.


53-1001156-01

swFCPortRxFrames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14

5 swFCPortRxFrames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14

Counts the number of Fibre Channel frames that the port has received.


53-1001156-01

613

5 swFCPortRxC2Frames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15

swFCPortRxC2Frames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15

Counts the number of Class 2 frames that the port has received.


53-1001156-01

swFCPortRxC3Frames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16

5 swFCPortRxC3Frames 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16

Counts the number of Class 3 frames that the port has received.


53-1001156-01

615

5 swFCPortRxLCs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17

swFCPortRxLCs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17

Counts the number of link control frames that the port has received.


53-1001156-01

swFCPortRxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18

5 swFCPortRxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18

Counts the number of multicast frames that the port has received.


53-1001156-01

617

5 swFCPortTooManyRdys 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19

swFCPortTooManyRdys 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19

Counts the number of times that RDYs exceeds the frames received.


53-1001156-01

swFCPortNoTxCredits 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20

5 swFCPortNoTxCredits 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20

Counts the number of times that the transmit credit has reached 0.


53-1001156-01

619

5 swFCPortRxEncInFrs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21

swFCPortRxEncInFrs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21

Counts the number of encoding error or disparity error inside frames received.


53-1001156-01

swFCPortRxCrcs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22

5 swFCPortRxCrcs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22

Counts the number of CRC errors detected for frames received.


53-1001156-01

621

5 swFCPortRxTruncs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23

swFCPortRxTruncs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23

Counts the number of truncated frames that the port has received.


53-1001156-01

swFCPortRxTooLongs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24

5 swFCPortRxTooLongs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24

Counts the number of received frames that are too long.


53-1001156-01

623

5 swFCPortRxBadEofs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25

swFCPortRxBadEofs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25

Counts the number of received frames that have bad EOF delimiters.


53-1001156-01

swFCPortRxEncOutFrs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26

5 swFCPortRxEncOutFrs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26

Counts the number of encoding error or disparity error outside frames received.


53-1001156-01

625

5 swFCPortRxBadOs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27

swFCPortRxBadOs 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27

Counts the number of invalid ordered sets received.


53-1001156-01

swFCPortC3Discards 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28

5 swFCPortC3Discards 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28

Counts the number of Class 3 frames that the port has discarded.


53-1001156-01

627

5 swFCPortMcastTimedOuts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29

swFCPortMcastTimedOuts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29

Counts the number of multicast frames that have been timed out.


53-1001156-01

swFCPortTxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30

5 swFCPortTxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30

Counts the number of multicast frames that have been transmitted.


53-1001156-01

629

5 swFCPortLipIns 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31

swFCPortLipIns 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31

Counts the number of loop initializations that have been initiated by loop devices attached.


53-1001156-01

swFCPortLipOuts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32

5 swFCPortLipOuts 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32

Counts the number of loop initializations that have been initiated by the port.


53-1001156-01

631

5 swFCPortLipLastAlpa 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33

swFCPortLipLastAlpa 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33

Indicates the physical address (AL_PA) of the loop device that initiated the last loop initialization.


53-1001156-01

swFCPortWwn 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34

5 swFCPortWwn 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34

The WWN of the Fibre Channel port. The contents of an instance are in IEEE extended format, as specified in FC-PH.


53-1001156-01

633

5 swFCPortSpeed 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35

swFCPortSpeed 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35

Values

The desired baud rate for the port.

The baud rate can be 1 Gbit/sec, 2 Gbit/sec, autonegotiate, or 4 Gbit/sec or 8 Gbit/sec. 4 Gbit/sec is only applicable to the Brocade 4100, 4900, 7500, 7600, and 48000.8 Gbit/sec is only applicable to the Brocade DCX director.


53-1001156-01

swFCPortName 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36

5 swFCPortName 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36

Supported in Fabric OS v4.1.x and later. A string that indicates the name of the addressed port.

NOTE

The names should be persistent across switch reboots. Port names do not have to be unique within a switch or within a fabric.


53-1001156-01

635

5 swFCPortSpecifier 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37

swFCPortSpecifier 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37

This string indicates the physical port number of the addressed port. This string can be entered as argument on CLI commands such as portShow or wherever a physical port number is expected.

The format of the string is:

<slot/>port

, 'slot' being present only for bladed systems.

For directors, such as Brocade 48000: swFCPortSpecifier.64 = 4/15

For non-bladed systems, such as Brocade 4100: swFCPortSpecifier.31 = 30

For LISL, the value is -1/<port #>.


53-1001156-01

swFCPortFlag 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38

5 swFCPortFlag 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38

This string is a bit map of the port status flags, including the port type.

• virtual (0) is the LISL value

• physical (1)


53-1001156-01

637

5 swFCPortBrcdType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39

swFCPortBrcdType 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39

This string indicates the Brocade port type.


53-1001156-01

Name Server Database Group

swNsLocalNumEntry 1.3.6.1.4.1.1588.2.1.1.1.7.1

The number of local Name Server entries.

Name Server Database Group

5


53-1001156-01

639

5 swNsLocalTable 1.3.6.1.4.1.1588.2.1.1.1.7.2

swNsLocalTable 1.3.6.1.4.1.1588.2.1.1.1.7.2

The table of local Name Server entries.


53-1001156-01

swNsLocalEntry 1.3.6.1.4.1.1588.2.1.1.1.7.2.1

5 swNsLocalEntry 1.3.6.1.4.1.1588.2.1.1.1.7.2.1

Index

An entry from the local Name Server database.

swNsEntryIndex


53-1001156-01

641

5 swNsEntryIndex 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1

swNsEntryIndex 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1

The index of the Name Server database entry.


53-1001156-01

swNsPortID 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2

5 swNsPortID 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2

The Fibre Channel port address ID of the entry.


53-1001156-01

643

5 swNsPortType 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.3

swNsPortType 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.3

Values

The type of port for this entry.

Possible values, as defined in FC-GS-2, are:

• nPort (1)

• nlPort (2)


53-1001156-01

swNsPortName 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.4

5 swNsPortName 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.4

The Fibre Channel WWN of the port entry.


53-1001156-01

645

5 swNsPortSymb 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.5

swNsPortSymb 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.5

The contents of a symbolic name of the port entry. In FC-GS-2, a symbolic name consists of a byte array of 1 through 256 bytes, and the first byte of the array specifies the length of its contents. This object variable corresponds to the contents of the symbolic name, with the first byte removed.


53-1001156-01

swNsNodeName 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.6

5 swNsNodeName 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.6

The Fibre Channel WWN of the associated node, as defined in FC-GS-2.


53-1001156-01

647

5 swNsNodeSymb 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.7

swNsNodeSymb 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.7

The contents of a Symbolic Name of the node associated with the entry. In FC-GS-2, a Symbolic

Name consists of a byte array of 1 through 256 bytes, and the first byte of the array specifies the length of its contents. This object variable corresponds to the contents of the Symbolic Name, with the first byte removed.


53-1001156-01

swNsIPA 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.8

5 swNsIPA 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.8

The Initial Process Associators of the node for the entry as defined in FC-GS-2. This value is read-only and cannot be changed.


53-1001156-01

649

5 swNsIpAddress 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.9

swNsIpAddress 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.9

The IP address of the node for the entry as defined in FC-GS-2. The format of the address is in IPv6.


53-1001156-01

swNsCos 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10

5 swNsCos 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10

The class of services supported by the port. This value is a hard-coded bitmap and indicates the supported services as follows:

•

Class F (1)

•

Class 1 (2)

•

Class F-1 (3)

•

Class 2 (4)

•

Class F-2 (5)

•

Class 1-2 (6)

•

Class F-1-2 (7)

•

Class 3 (8)

•

Class F-3 (9)

•

Class 1-3 (10)

•

Class F-1-3 (11)

•

Class 2-3 (12)

•

Class F-2-3 (13)

•

Class 1-2-3 (14)

•

Class F-1-2-3 (15)


53-1001156-01

651

5 swNsFc4 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.11

swNsFc4 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.11

The FC-4s supported by the port, as defined in FC-GS-2.


53-1001156-01

swNsIpNxPort 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.12

5 swNsIpNxPort 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.12

The object identifies IpAddress of the Nx_Port for the entry.


53-1001156-01

653

5 swNsWwn 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.13

swNsWwn 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.13

The object identifies the World Wide Name (WWN) of the Fx_Port for the entry.


53-1001156-01

swNsHardAddr 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.14

5 swNsHardAddr 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.14

The object identifies the 24-bit hard address of the node for the entry.


53-1001156-01

655

5

Event Group

Event Group

Logically, the swEventTable is separate from the error log since it is essentially a view of the error log within a particular time window.


53-1001156-01

swEventTrapLevel 1.3.6.1.4.1.1588.2.1.1.1.8.1

5 swEventTrapLevel 1.3.6.1.4.1.1588.2.1.1.1.8.1


, in the absence of swEventTrapLevel,

specifies the trap severity level of each defined trap recipient host. This object specifies the swEventTrap level in conjunction with an event’s severity level. When an event occurs, and if its severity level is at or below the value specified by the object instance, the agent sends the associated swEventTrap to configured recipients.

This object is obsoleted by

swFwLastSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12

and


.


53-1001156-01

657

5 swEventNumEntries 1.3.6.1.4.1.1588.2.1.1.1.8.4

swEventNumEntries 1.3.6.1.4.1.1588.2.1.1.1.8.4

Values

The number of entries in the event table.

(v3.0 only) The value ranges from 0 to 64.



(v4.4 and above) The value ranges from 0 to 1024.

(v6.0 and above) The value ranges from 0 to 1024


53-1001156-01

swEventTable 1.3.6.1.4.1.1588.2.1.1.1.8.5

5 swEventTable 1.3.6.1.4.1.1588.2.1.1.1.8.5

The table of event entries. The events will be received from the CHASSIS and the created logical switches.

Only external RASlog messages are supported. Fabric OS v6.2.0 does not have Panic or Debug level messages. All messages are documented in the Fabric OS Message Reference.


53-1001156-01

659

5 swEventEntry 1.3.6.1.4.1.1588.2.1.1.1.8.5.1

swEventEntry 1.3.6.1.4.1.1588.2.1.1.1.8.5.1

Index

An entry of the event table.

swEventIndex


53-1001156-01

swEventIndex 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1

5 swEventIndex 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1

The index of the event entry.


53-1001156-01

661

5 swEventTimeInfo 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2

swEventTimeInfo 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2

The date and time that this event occurred.

The return string is displayed using the following format:

YYYY/MM/DD-hh:mm:ss

Where:

YYYY = Year

MM = Month

DD = Date hh = Hour mm = Minute ss = Seconds

For example:

2005/12/05-07:33:41


53-1001156-01

swEventLevel 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3

5 swEventLevel 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3

Values

The severity level of this event entry.


• critical (1)

• error (2)

• warning (3)

• informational (4)


53-1001156-01

663

5 swEventRepeatCount 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4

swEventRepeatCount 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4

If the most recent event is the same as the previous, this number increments by 1, and is the count of consecutive times this particular event has occurred.


53-1001156-01

swEventDescr 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5

5 swEventDescr 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5

A textual description of the event.

For Fabric OS v6.2.0, the format of error messages has changed. This field now uses the message title and number (for example, WEBD-1006) and the message text. Previously this field used the task ID, and all the message number and message text. For more information on error messages, refer to the Fabric OS Message Reference.


53-1001156-01

665

5

Fabric Watch Group

Fabric Watch Group

The Fabric Watch group contains one license scalar and two tables.

•

The scalar, swFwFabricWatchLicense, is used to tell is if the switch has proper license for

Fabric Watch.

•

One table, “swFwClassAreaTable 1.3.6.1.4.1.1588.2.1.1.1.10.2” , contains classArea

information such as threshold unit string, time base, low thresholds, and so forth.

SwFwClassAreaEntry contains control information for a particular class/area's thresholds.

•

The other table, “swFwThresholdTable 1.3.6.1.4.1.1588.2.1.1.1.10.3”

, contains individual threshold information such as name, label, last event, and so forth. The thresholds are contained in SwFwThresholdEntry.


53-1001156-01

swFwFabricWatchLicense 1.3.6.1.4.1.1588.2.1.1.1.10.1

swFwFabricWatchLicense 1.3.6.1.4.1.1588.2.1.1.1.10.1

If the license key is installed on the switch for Fabric Watch, the return value is swFwLicensed; otherwise, the value is swFwNotLicensed.

5


53-1001156-01

667

5 swFwClassAreaTable 1.3.6.1.4.1.1588.2.1.1.1.10.2

swFwClassAreaTable 1.3.6.1.4.1.1588.2.1.1.1.10.2

The table of classes and areas.


53-1001156-01

swFwClassAreaEntry 1.3.6.1.4.1.1588.2.1.1.1.10.2.1

5 swFwClassAreaEntry 1.3.6.1.4.1.1588.2.1.1.1.10.2.1

Index

An entry of the classes and areas.

swFwClassAreaIndex


53-1001156-01

669

5 swFwClassAreaIndex 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1

swFwClassAreaIndex 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1

This index represents the Fabric Watch classArea combination.


53-1001156-01

swFwWriteThVals 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.2

5 swFwWriteThVals 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.2

This applies or cancels the configuration value changes.

For a read operation, the return value is always swFwCancelWrite.

The following custom configuration variables can be modified:

• swFwCustUnit

• swFwCustTimebase

• swFwCustLow

• swFwCustHigh

• swFwCustBufSize

Changes to these custom configuration variables can be saved by setting this variable to swFwApplyWrite; they can be removed by setting this variable to swFwCancelWrite.


53-1001156-01

671

5 swFwDefaultUnit 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.3

swFwDefaultUnit 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.3

A default unit string name, used to identify the unit of measure for a Fabric Watch classArea combination.

C = environment (class), temperature (area).

RPM = environment (class), fan (area).


53-1001156-01

swFwDefaultTimebase 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.4

5 swFwDefaultTimebase 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.4

A default polling period for the Fabric Watch classArea combination. swFwTbMin = port (class), link loss (area).

swFwTbNone = environment (class), temperature (area).


53-1001156-01

673

5 swFwDefaultLow 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.5

swFwDefaultLow 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.5

A default low threshold value.


53-1001156-01

swFwDefaultHigh 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.6

5 swFwDefaultHigh 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.6

A default high threshold value.


53-1001156-01

675

5 swFwDefaultBufSize 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.7

swFwDefaultBufSize 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.7

A default buffer size value.


53-1001156-01

swFwCustUnit 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.8

5 swFwCustUnit 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.8

A customizable unit string name, used to identify the unit of measure for a Fabric Watch classArea combination.

C = environment (class), temperature (area).

RPM = environment (class), fan (area).


53-1001156-01

677

5 swFwCustTimebase 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.9

swFwCustTimebase 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.9

A customizable polling period for the Fabric Watch classArea combination. swFwTbMin = port (class), link loss (area).

swFwTbNone = environment (class), temperature (area).


53-1001156-01

swFwCustLow 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.10

5 swFwCustLow 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.10

A customizable low-threshold value for a Fabric Watch classArea combination.


53-1001156-01

679

5 swFwCustHigh 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.11

swFwCustHigh 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.11

A customizable high-threshold value for a Fabric Watch classArea combination.


53-1001156-01

swFwCustBufSize 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.12

5 swFwCustBufSize 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.12

A customizable buffer size value for a Fabric Watch classArea combination.


53-1001156-01

681

5 swFwThLevel 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.13

swFwThLevel 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.13

swFwThLevel is used to point to the current level for classArea values. It is either default or custom.

For a read operation, the return value is either 2 (swFwDefault) or 3 (swFwCustom). 1

(swFwReserved) is obsolete.

If the write operation sets the variable to 2 (swFwDefault), the following default configuration variables are used for the Fabric Watch classArea combination: swFwDefaultUnit swFwDefaultTimebase swFwDefaultLow swFwDefaultHigh swFwDefaultBufSize

If the write operation sets the variable to 3 (swFwCustom), the following custom configuration variables are used for the Fabric Watch classArea combination: swFwCustUnit swFwCustTimebase swFwCustLow swFwCustHigh swFwCustBufSize


53-1001156-01

swFwWriteActVals 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.14

5 swFwWriteActVals 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.14

This applies or cancels the alarm value changes.

For a read operation, the return value is always swFwCancelWrite.

The following are the custom alarm variables that can be modified: swFwCustChangedActs swFwCustExceededActs swFwCustBelowActs swFwCustAboveActs swFwCustInBetweenActs

Changes to these custom alarm variables can be saved by setting this variable to swFwApplyWrite.

Changes to these custom alarm variables can be removed by setting this variable to swFwCancelWrite.


53-1001156-01

683

5 swFwDefaultChangedActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.15

swFwDefaultChangedActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.15

Default action matrix for changed event.


53-1001156-01

swFwDefaultExceededActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.16

5 swFwDefaultExceededActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.16

Default action matrix for an exceeded event. The exceeded value might be either above the high threshold or below the low threshold.


53-1001156-01

685

5 swFwDefaultBelowActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.17

swFwDefaultBelowActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.17

Default action matrix for below event.


53-1001156-01

swFwDefaultAboveActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.18

5 swFwDefaultAboveActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.18

Default action matrix for above event.


53-1001156-01

687

5 swFwDefaultInBetweenActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.19

swFwDefaultInBetweenActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.19

Default action matrix for in-between event.


53-1001156-01

swFwCustChangedActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.20

5 swFwCustChangedActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.20

Custom action matrix for changed event.


53-1001156-01

689

5 swFwCustExceededActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.21

swFwCustExceededActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.21

Custom action matrix for an exceeded event.


53-1001156-01

swFwCustBelowActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.22

5 swFwCustBelowActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.22

Custom action matrix for below event.


53-1001156-01

691

5 swFwCustAboveActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.23

swFwCustAboveActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.23

Custom action matrix for above event.


53-1001156-01

swFwCustInBetweenActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.24

5 swFwCustInBetweenActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.24

Custom action matrix for in-between event.


53-1001156-01

693

5 swFwValidActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.25

swFwValidActs 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.25

Matrix of valid acts for a classArea.


53-1001156-01

swFwActLevel 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.26

5 swFwActLevel 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.26

Pointer to the current level for classArea values. It is either default or custom.

For a read operation, the return value is either 2 (swFwDefault) or 3 (swFwCustom). 1

(swFwReserved) is obsolete.

If the write operation sets the variable to 2 (swFwDefault), the following default action matrix variables are used for the Fabric Watch classArea combination: swFwDefaultChangedActs swFwDefaultExceededActs swFwDefaultBelowActs swFwDefaultAboveActs swFwDefaultInBetweenActs

If the write operation sets the variable to 3 (swFwCustom), the following custom action matrix variables are used for the Fabric Watch classArea combination: swFwCustChangedActs swFwCustExceededActs swFwCustBelowActs swFwCustAboveActs swFwCustInBetweenActs


53-1001156-01

695

5 swFwThresholdTable 1.3.6.1.4.1.1588.2.1.1.1.10.3

swFwThresholdTable 1.3.6.1.4.1.1588.2.1.1.1.10.3

The table of individual thresholds.


53-1001156-01

swFwThresholdEntry 1.3.6.1.4.1.1588.2.1.1.1.10.3.1

5 swFwThresholdEntry 1.3.6.1.4.1.1588.2.1.1.1.10.3.1

Index

An entry of an individual threshold.

swFwClassAreaIndex, swFwThresholdIndex


53-1001156-01

697

5 swFwThresholdIndex 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1

swFwThresholdIndex 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1

Represents the element index of a threshold.

For environment class, the indexes are from 2 through (number of environment sensors+1).

For example, the indexes for environment class temperature area are: envTemp001: index of 2 envTemp002: index of 3 envTemp003: index of 4 envTemp004: index of 5 envTemp005: index of 6

For port-related classes such as E_Port, the indexes are from 1 through (number of ports). For example, the indexes for E_Port classlink loss area: eportLink000: index of 1 eportLink001: index of 2 eportLink002: index of 3 eportLink003: index of 4 eportLink004: index of 5 eportLink005: index of 6 eportLink006: index of 7 eportLink007: index of 8 eportLink008: index of 9 eportLink009: index of 10 eportLink010: index of 11 eportLink011: index of 12 eportLink012: index of 13 eportLink013: index of 14 eportLink014: index of 15 eportLink015: index of 16


53-1001156-01

swFwStatus 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.2

5 swFwStatus 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.2

Indicates whether a threshold is enabled or disabled.


53-1001156-01

699

5 swFwName 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3

swFwName 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3

Name of the threshold.

For examples, refer to

Table 15

.

TABLE 15

swFwName Objects and Object Types swFwName Objects (swFwName) Object Types (Threshold Names) envFan001 envPS002 envTemp001 gbicTemp001 gbicRXP001 gbicTXP001 gbicCrnt001 eportCRCs007 eportLink007 eportProtoErr007 eportRXPerf007 eportSignal007 eportState007 eportSync007 eportTXPerf007 eportWords007

Env Fan 1

Env Power Supply 2

Env Temperature 1

GBIC Temperature 1

GBIC RX power 1

GBIC TX power 1

GBIC Current 1

E Port Invalid CRCs 7

E Port Link Failures 7

E Port Protocol Errors 7

E Port RX Performance 7

E Port Loss of Signal 7

E Port State Changes 7

E Port Loss of Sync 7

E Port TX Performance 7

E Port Invalid Words 7 fabricED000 fabricFL000

Fabric E-port down

Fabric Fabric login fabricGS000 fcuportCRCs013 fcuportLink013 fcuportProtoErr0 fcuportRXPerf013 fcuportSignal013 fcuportState013 fcuportSync013 fcuportTXPerf013

Fabric GBIC change 0

FCU Port Invalid CRCs 13

FCU Port Link Failures 13

FCU Port Protocol Errors 13

FCU Port RX Performance 13

FCU Port Loss of Signal 13

FCU Port State Changes 13

FCU Port Loss of Sync 13

FCU Port TX Performance 13


53-1001156-01


53-1001156-01

swFwName 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3

5

TABLE 15

swFwName Objects and Object Types (Continued) swFwName Objects (swFwName) Object Types (Threshold Names) (Continued) fcuportWords013 portCRCs000 Port Invalid CRCs 0 portLink000 portProtoErr000 portRXPerf000 portSignal000 portState000 portSync000 portTXPerf000 portWords000 fopportCRCs013 fopportLink013 fopportProtoErr0 fopportRXPerf013 fopportSignal013 fopportState013 fopportSync013 fopportTXPerf013 fopportWords013

FCU Port Invalid Words 13

Port Invalid CRCs 0

Port Link Failures 0

Port Protocol Errors 0

Port RX Performance 0

Port Loss of Signal 0

Port State Changes 0

Port Loss of Sync 0

Port TX Performance 0

Port Invalid Words 0

FOP Port Invalid CRCs 13

FOP Port Link Failures 13

FOP Port Protocol Errors 13

FOP Port RX Performance 13

FOP Port Loss of Signal 13

FOP Port State Changes 13

FOP Port Loss of Sync 13

FOP Port TX Performance 13

FOP Port Invalid Words 13

701

5 swFwLabel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4

swFwLabel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4

Label of the threshold.

Refer to “swFwName 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3” on page 700.


53-1001156-01

swFwCurVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.5

5 swFwCurVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.5

Current counter of the threshold.


53-1001156-01

703

5 swFwLastEvent 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6

swFwLastEvent 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6

Last event type of the threshold.


53-1001156-01

swFwLastEventVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7

5 swFwLastEventVal 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7

Last event value of the threshold.


53-1001156-01

705

5 swFwLastEventTime 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8

swFwLastEventTime 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8

Last event time of the threshold. This value is in the same format as in swCurrentDate.


53-1001156-01

swFwLastState 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9

5 swFwLastState 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9

Last event state of the threshold.


53-1001156-01

707

5 swFwBehaviorType 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.10

swFwBehaviorType 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.10

A behavior of which the thresholds generate event.


53-1001156-01

swFwBehaviorInt 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.11

5 swFwBehaviorInt 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.11

An integer of which the thresholds generate continuous event.


53-1001156-01

709

5 swFwLastSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12

swFwLastSeverityLevel 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12

This object is a last event severity level of the threshold. This object obsoletes swEventTrapLevel

1.3.6.1.4.1.1588.2.1.1.1.8.1

.


53-1001156-01

End Device Group

End Device Group

swEndDeviceRlsTable 1.3.6.1.4.1.1588.2.1.1.1.21.1

The table of RLS for individual end devices. By default, no data appears in this table.

5


53-1001156-01

711

5 swEndDeviceRlsEntry 1.3.6.1.4.1.1588.2.1.1.1.21.1.1

swEndDeviceRlsEntry 1.3.6.1.4.1.1588.2.1.1.1.21.1.1

Index

An entry of an individual end devices' RLS.

swEndDevicePort, swEndDeviceAlpa

Since Brocade switches start with port # 0, the SNMP port # should be physical port # plus 1. In turn, that means that SNMP port # 3 translates to port # 2.


53-1001156-01

swEndDevicePort 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.1

5 swEndDevicePort 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.1

This object represents the port of the local switch to which the end device is connected. This is an obsolete entry and does not show any value.


53-1001156-01

713

5 swEndDeviceAlpa 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.2

swEndDeviceAlpa 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.2

This object represents the AL_PA of the end device. SNMP AL_PA number should be the logical

AL_PA number plus 1. For example, SNMP AL_PA number 0xf0 translates to 0xef.

This is an obsolete entry and does not show any value.


53-1001156-01

swEndDevicePortID 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.3

5 swEndDevicePortID 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.3

The Fibre Channel port address ID of the entry.


53-1001156-01

715

5 swEndDeviceLinkFailure 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.4

swEndDeviceLinkFailure 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.4

Link failure count for the end device.


53-1001156-01

swEndDeviceSyncLoss 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.5

5 swEndDeviceSyncLoss 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.5

Sync loss count for the end device.


53-1001156-01

717

5 swEndDeviceSigLoss 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.6

swEndDeviceSigLoss 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.6

Sig loss count for the end device.


53-1001156-01

swEndDeviceProtoErr 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.7

5 swEndDeviceProtoErr 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.7

Protocol err count for the end device.


53-1001156-01

719

5 swEndDeviceInvalidWord 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.8

swEndDeviceInvalidWord 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.8

Invalid word count for the end device.


53-1001156-01

swEndDeviceInvalidCRC 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.9

5 swEndDeviceInvalidCRC 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.9

Invalid CRC count for the end device.

Switch Group

Not supported.


53-1001156-01

721

5 swGroupTable 1.3.6.1.4.1.1588.2.1.1.1.22.1

swGroupTable 1.3.6.1.4.1.1588.2.1.1.1.22.1

The table of groups. This is not available on all versions of Fabric OS.


53-1001156-01

swGroupEntry 1.3.6.1.4.1.1588.2.1.1.1.22.1.1

5 swGroupEntry 1.3.6.1.4.1.1588.2.1.1.1.22.1.1

Index

An entry of table of groups.

swGroupIndex


53-1001156-01

723

5 swGroupIndex 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.1

swGroupIndex 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.1

This object is the group index, starting from 1.


53-1001156-01

swGroupName 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.2

5 swGroupName 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.2

This object identifies the name of the group.


53-1001156-01

725

5 swGroupType 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.3

swGroupType 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.3

This object identifies the type of the group.


53-1001156-01

swGroupMemTable 1.3.6.1.4.1.1588.2.1.1.1.22.2

swGroupMemTable 1.3.6.1.4.1.1588.2.1.1.1.22.2

The table of members of all groups. This might not be available on all versions of the Fabric OS.

5


53-1001156-01

727

5 swGroupMemEntry 1.3.6.1.4.1.1588.2.1.1.1.22.2.1

swGroupMemEntry 1.3.6.1.4.1.1588.2.1.1.1.22.2.1

Index

An entry for a member of a group.

swGroupID, swGroupMemWwn


53-1001156-01

swGroupID 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.1

5 swGroupID 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.1

This object identifies the Group ID of the member switch.


53-1001156-01

729

5 swGroupMemWwn 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.2

swGroupMemWwn 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.2

This object identifies the WWN of the member switch.


53-1001156-01

swGroupMemPos 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.3

5 swGroupMemPos 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.3

This object identifies the position of the member switch in the group, based on the order that the switches were added in the group.


53-1001156-01

731

5

ASIC Performance Monitoring Group

ASIC Performance Monitoring Group

swBlmPerfALPAMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.1

AL_PA monitoring counter table.

For the Brocade 4100, 12 filter monitors per port are supported.


53-1001156-01

swBlmPerfALPAMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.1.1

5 swBlmPerfALPAMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.1.1

Index

AL_PA monitoring counter for given AL_PA.

swEndDevicePort, swEndDeviceAlpa


53-1001156-01

733

5 swBlmPerfAlpaPort 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.1

swBlmPerfAlpaPort 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.1

This object identifies the port index of the switch.


53-1001156-01

swBlmPerfAlpaIndx 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.2

5 swBlmPerfAlpaIndx 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.2

This object identifies the AL_PA index. There can be 126 AL_PA values.


53-1001156-01

735

5 swBlmPerfAlpa 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.3

swBlmPerfAlpa 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.3

This object identifies the AL_PA values. These values range between x'01' and x'EF' (1 to 239).

AL_PA value x'00' is reserved for FL_Port. If Alpha device is invalid, then it will have -1 value.


53-1001156-01

swBlmPerfAlpaCRCCnt 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.4

5 swBlmPerfAlpaCRCCnt 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.4

Get CRC count for given AL_PA and port. This monitoring provides information on the number of

CRC errors that occurred on the frames destined to each possible AL_PA attached to a specific port.

For the Brocade 4100, this value will always be 0. CRC counters are not supported on this platform.


53-1001156-01

737

5 swBlmPerfEEMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.2

swBlmPerfEEMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.2

End-to-end monitoring counter table.


53-1001156-01

swBlmPerfEEMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.2.1

5 swBlmPerfEEMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.2.1

Index

End-to-end monitoring counter for given port.

swBlmPerfEEPort, swBlmPerfEERefKey


53-1001156-01

739

5 swBlmPerfEEPort 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.1

swBlmPerfEEPort 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.1

This object identifies the port number of the switch.


53-1001156-01

swBlmPerfEERefKey 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.2

swBlmPerfEERefKey 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.2

This object identifies the reference number of the counter. This reference is a number assigned when a filter is created. In the SNMP Index, start with one instead of 0, add one to the actual reference key.

5


53-1001156-01

741

5 swBlmPerfEECRC 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.3

swBlmPerfEECRC 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.3

End-to-end CRC error for the frames that matched the SID-DID pair.


53-1001156-01

swBlmPerfEEFCWRx 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.4

5 swBlmPerfEEFCWRx 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.4

Get end-to-end count of Fibre Channel words (FCW) received by the port that matched the SID-DID pair.


53-1001156-01

743

5 swBlmPerfEEFCWTx 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.5

swBlmPerfEEFCWTx 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.5

Get end-to-end count of Fibre Channel words (FCW) transmitted by the port that matched the

SID-DID pair.


53-1001156-01

swBlmPerfEESid 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.6

5 swBlmPerfEESid 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.6

Gets DID information by reference number.


53-1001156-01

745

5 swBlmPerfEEDid 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.7

swBlmPerfEEDid 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.7

Gets SID information by reference number. SID (Source Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N_Port from which the frame was sent.


53-1001156-01

swBlmPerfFltMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.3

5 swBlmPerfFltMntTable 1.3.6.1.4.1.1588.2.1.1.1.23.3

Filter-based monitoring counter.


53-1001156-01

747

5 swBlmPerfFltMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.3.1

swBlmPerfFltMntEntry 1.3.6.1.4.1.1588.2.1.1.1.23.3.1

Index

Filter-based monitoring counter for given port.

swBlmPerfFltPort, swBlmPerfFltRefkey


53-1001156-01

swBlmPerfFltPort 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.1

5 swBlmPerfFltPort 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.1

This object identifies the port number of the switch.


53-1001156-01

749

5 swBlmPerfFltRefkey 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.2

swBlmPerfFltRefkey 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.2

This object identifies the reference number of the filter. This reference number is assigned when a filter is created. In the SNMP Index, start with one instead of 0, add one to actual reference key.


53-1001156-01

swBlmPerfFltCnt 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.3

5 swBlmPerfFltCnt 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.3

Get statistics of filter-based monitor. Filter-based monitoring provides information about a filter hit count, such as:

•

Read command

•

SCSI or IP traffic

•

SCSI Read/Write


53-1001156-01

751

5 swBlmPerfFltAlias 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.4

swBlmPerfFltAlias 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.4

Alias name for the filter.


53-1001156-01

Trunking Group

Trunking Group

swSwitchTrunkable 1.3.6.1.4.1.1588.2.1.1.1.24.1

Whether the switch supports the trunking feature or not: no (0) or yes (8).

5


53-1001156-01

753

5 swTrunkTable 1.3.6.1.4.1.1588.2.1.1.1.24.2

swTrunkTable 1.3.6.1.4.1.1588.2.1.1.1.24.2

Displays trunking information for the switch.

For the Brocade 4100, cc ports per trunk are supported.


53-1001156-01

swTrunkEntry 1.3.6.1.4.1.1588.2.1.1.1.24.2.1

5 swTrunkEntry 1.3.6.1.4.1.1588.2.1.1.1.24.2.1

Index

Entry for the trunking table.

swTrunkPortIndex


53-1001156-01

755

5 swTrunkPortIndex 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.1

swTrunkPortIndex 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.1

This object identifies the switch port index.

The value of a port index is extracted from the second octet of the port WWN stored in

swFCPortWwn (Refer to swFCPortWwn 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34

in the Fibre Channel Port

Group).


53-1001156-01

swTrunkGroupNumber 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.2

5 swTrunkGroupNumber 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.2

This object is a logical entity that specifies the group number to which the port belongs. If this value is 0, the port is not trunked.


53-1001156-01

757

5 swTrunkMaster 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.3

swTrunkMaster 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.3

Port number that is the trunk master of the group. The trunk master implicitly defines the group. All ports with the same master are considered to be part of the same group.


53-1001156-01

swPortTrunked 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.4

5 swPortTrunked 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.4

The active trunk status of the member port. Values are enabled (1) or disabled (0).


53-1001156-01

759

5 swTrunkGrpTable 1.3.6.1.4.1.1588.2.1.1.1.24.3

swTrunkGrpTable 1.3.6.1.4.1.1588.2.1.1.1.24.3

Displays trunking performance information for the switch.


53-1001156-01

swTrunkGrpEntry 1.3.6.1.4.1.1588.2.1.1.1.24.3.1

5 swTrunkGrpEntry 1.3.6.1.4.1.1588.2.1.1.1.24.3.1

Index

Entry for the trunking group table.

swTrunkGrpNumber


53-1001156-01

761

5 swTrunkGrpNumber 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.1

swTrunkGrpNumber 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.1

This object is a logical entity that specifies the group number to which port belongs.


53-1001156-01

swTrunkGrpMaster 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.2

5 swTrunkGrpMaster 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.2

This object gives the master port ID for the trunk group.


53-1001156-01

763

5 swTrunkGrpTx 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.3

swTrunkGrpTx 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.3

Gives the aggregate value of the transmitted words from this trunk group.

NOTE

The syntax for this MIB variable is an OCTET STRING. The output is shown in hexadecimal value. The value of swTrunkGrpTx is the 4-byte word transmitted in the TrunkGrp port. This value can be obtained through the CLI in the output of the portStatsShow command (stat_wtx value) for the corresponding trunk ports.


53-1001156-01

swTrunkGrpRx 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.4

5 swTrunkGrpRx 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.4

Gives the aggregate value of the received words by this trunk group.

The syntax for this MIB variable is an OCTET STRING. The output is shown in hexadecimal value.

The value of swTrunkGrpRx is the 4-byte word received in the TrunkGrp port. This value can be obtained through the CLI in the output of the portStatsShow command (stat_wrx value) for the corresponding trunk ports.


53-1001156-01

765

5 swTopTalkerMntMode 1.3.6.1.4.1.1588.2.1.1.1.25.1

swTopTalkerMntMode 1.3.6.1.4.1.1588.2.1.1.1.25.1

This object gives the mode in which toptalker is installed. Fabricmode(1) and fportmode(2) are the possible modes.


53-1001156-01

swTopTalkerMntNumEntries 1.3.6.1.4.1.1588.2.1.1.1.25.2

5 swTopTalkerMntNumEntries 1.3.6.1.4.1.1588.2.1.1.1.25.2

This object provides the number of toptalking flows that are existing in the switch.


53-1001156-01

767

5 swTopTalkerMntTable 1.3.6.1.4.1.1588.2.1.1.1.25.3

swTopTalkerMntTable 1.3.6.1.4.1.1588.2.1.1.1.25.3

Table to display toptalkingflows.


53-1001156-01

swTopTalkerMntEntry 1.3.6.1.4.1.1588.2.1.1.1.25.3.1

5 swTopTalkerMntEntry 1.3.6.1.4.1.1588.2.1.1.1.25.3.1

Entry for the toptalkingflows.


53-1001156-01

769

5 swTopTalkerMntIndex 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.1

swTopTalkerMntIndex 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.1

This object identifies the list/object entry. The possibles values are one to maximum number of entries.


53-1001156-01

swTopTalkerMntPort 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.2

5 swTopTalkerMntPort 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.2

This object identifies the switch port number on which the F_port mode toptalker is added. This attribute is applicable to F_port mode only.


53-1001156-01

771

5 swTopTalkerMntSpid 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.3

swTopTalkerMntSpid 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.3

This object identifies the SID of the host.


53-1001156-01

swTopTalkerMntDpid 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.4

5 swTopTalkerMntDpid 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.4

This object identifies the DID of the SID-DID pair.


53-1001156-01

773

5 swTopTalkerMntflow 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.5

swTopTalkerMntflow 1.3.6.1.4.1.1588.2.1.1.1.25.3.1.5

This object identifies the traffic flow in MB/sec.


53-1001156-01

High-Availability MIB Objects

Chapter

6

This chapter provides descriptions and other information specific to High-Availability MIB object types and includes the following sections:

•

HA MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775

•

High-Availability Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777

•

FRU Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 779

•

FRU History Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 788

•

CP Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797

•

HA-MIB Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803

HA MIB Overview

The HA-MIB provides information about the High Availability features of Fabric OS v6.2.0. This MIB is supported only in Fabric OS v4.1.0 and later (and is not supported in Fabric OS v3.x or Fabric OS v2.6.x).

The HA-MIB depends on the SW-MIB. This dependency requires a management application to load the SNMP-FRAMEWORK MIB, then the SW-MIB, and finally the Entity MIB before it can load the

HA-MIB.

The descriptions of each of the MIB variables in this chapter come directly from the HA-MIB itself.

The object types in HA-MIB are organized into the following groupings:

•

High-Availability Group

•

HA-MIB Traps

Figure 52 and

Figure 53 depict the organization and structure of the HA-MIB file system.

- iso

- org

- dod

- internet

- private

- enterprises

- bsci

- commDev

- fibreChannel

- haMIB

- highAvailability

- haMIBTraps

FIGURE 52

HA-MIB Overall Tree Structure

- haMIB (1.3.6.1.4.1.1588.2.1.2)

- highAvailability (1.3.6.1.4.1.1588.2.1.2.1)

- haStatus 1.3.6.1.4.1.1588.2.1.2.1.1


53-1001156-01

775

776

6

HA MIB Overview

- fruTable 1.3.6.1.4.1.1588.2.1.2.1.5

- fruEntry 1.3.6.1.4.1.1588.2.1.2.1.5.1

- fruClass 1.3.6.1.4.1.1588.2.1.2.1.5.1.1

- fruStatus 1.3.6.1.4.1.1588.2.1.2.1.5.1.2

- fruObjectNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.3

- fruSupplierId 1.3.6.1.4.1.1588.2.1.2.1.5.1.4

- fruSupplierPartNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.5

- fruSupplierSerialNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.6

- fruSupplierRevCode 1.3.6.1.4.1.1588.2.1.2.1.5.1.7

- fruHistoryTable 1.3.6.1.4.1.1588.2.1.2.1.6

- fruHistoryEntry 1.3.6.1.4.1.1588.2.1.2.1.6.1

- fruHistoryIndex 1.3.6.1.4.1.1588.2.1.2.1.6.1.1

- fruHistoryClass 1.3.6.1.4.1.1588.2.1.2.1.6.1.2

- fruHistoryObjectNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.3

- fruHistoryEvent 1.3.6.1.4.1.1588.2.1.2.1.6.1.4

- fruHistoryTime 1.3.6.1.4.1.1588.2.1.2.1.6.1.5

- fruHistoryFactoryPartNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.6

- fruHistoryFactorySerialNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.7

- cpTable 1.3.6.1.4.1.1588.2.1.2.1.7

- cpEntry 1.3.6.1.4.1.1588.2.1.2.1.7.1

- cpStatus 1.3.6.1.4.1.1588.2.1.2.1.7.1.1

- cpIpAddress 1.3.6.1.4.1.1588.2.1.2.1.7.1.2

- cpIpMask 1.3.6.1.4.1.1588.2.1.2.1.7.1.3

- cpIpGateway 1.3.6.1.4.1.1588.2.1.2.1.7.1.4

- cpLastEvent 1.3.6.1.4.1.1588.2.1.2.1.7.1.5

- haMIBTraps

- haMIBTrapPrefix (1.3.6.1.4.1.1588.2.1.2.2.0)

- fruStatusChanged 1.3.6.1.4.1.1588.2.1.2.2.0.1

- cpStatusChanged 1.3.6.1.4.1.1588.2.1.2.2.0.2

- fruHistoryTrap 1.3.6.1.4.1.1588.2.1.2.2.0.3

FIGURE 53

haMIB and haMIBTraps Hierarchy

Table 16

lists the objects or definitions that are imported into the HA-MIB and the modules from which they are imported.

TABLE 16

Objects Imported into the HA-MIB

Object Imported from this module

MODULE-IDENTITY

OBJECT-TYPE

NOTIFICATION-TYPE

TimeTicks

Integer32

IpAddress mib-2 fibrechannel entPhysicalIndex entPhysicalName

DisplayString

TimeStamp

SNMPv2-SMI

SW-MIB

ENTITY-MIB

SNMPv2-TC


53-1001156-01



This section describes the MIB objects in the High-Availability group.

6


53-1001156-01

777

6 haStatus 1.3.6.1.4.1.1588.2.1.2.1.1

haStatus 1.3.6.1.4.1.1588.2.1.2.1.1

Values

Indicates whether the system is redundant.


•

1: redundant(0) Dual CP with standby CP ready to take over.

•

2: nonredundant(1) Single or Dual CP system where the standby CP is not available to take over operation of the switch.


53-1001156-01

FRU Table

6

FRU Table

fruTable 1.3.6.1.4.1.1588.2.1.2.1.5

This table inventories the field replaceable unit (FRU) slots available.

This table contains an entry for each entry in the entPhysicalTable that has entPhysicalClass set to

“Container (5)” and has a child entry having entPhysicalIsFRU set to “true (1)”.

In Fabric OS v6.1.0 and above the chassis is marked as a FRU. Unlike other FRUs the chassis FRU does not have a corresponding container entry.

Table 17 on page 779 includes information on all FRUs except the chassis.

TABLE 17

Valid FRU Counts for the Various Brocade Switches

Platform Blades Fans Power Supply WWN Card

Brocade 3850 NA NA

Brocade 3900

Brocade 4012

Brocade 4100

Brocade 4900

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000

Brocade 24000

Brocade 48000

Brocade DCX

Brocade DCX-4S

Brocade 300

Brocade 5100

Brocade 5300

NA

NA

NA

NA

NA

NA

NA

8 port blades

2 CP blades

8 port blades

2 CP blades

8 port blades

2 CP blades

8 port blades

2 CP blades

4 port blades

2 CP blades

NA

NA

NA

4 fans

(not a FRU)

6 fans in 3 FRUs

NA

3 fans in 3 FRUs

3 fans in 3 FRUs

3 fans in 3 FRUs

3 fans in 3 FRUs

3 fans in 3 FRUs

3 fans

3 fans

3 fans

3 fans

2 fans

3 fans

2 fans

3 fans

2 PS

(not a FRU)

2 PS

NA

2 PS

2 PS

2 PS

2 PS

2 PS

4 PS

4 PS

4 PS

4 PS

2 PS

1 PS

2 PS

2 PS

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

1 WWN

1 WWN

1 WWN

2 WWN

1 WWN


53-1001156-01

779

6 fruEntry 1.3.6.1.4.1.1588.2.1.2.1.5.1

fruEntry 1.3.6.1.4.1.1588.2.1.2.1.5.1

Index

An entry for FRU slot in the fruTable.

entPhysicalIndex


53-1001156-01

fruClass 1.3.6.1.4.1.1588.2.1.2.1.5.1.1

6 fruClass 1.3.6.1.4.1.1588.2.1.2.1.5.1.1

Values

The type of the FRU object that this slot can hold.


•

1: other(1)

•

2: unknown(2)

•

3: chassis(3)

•

4: cp(4)

•

5: other-CP(5)

•

6: switchblade(6)

•

7: wwn(7)

•

8: powerSupply(8)

•

9: fan(9)


53-1001156-01

781

6 fruStatus 1.3.6.1.4.1.1588.2.1.2.1.5.1.2

fruStatus 1.3.6.1.4.1.1588.2.1.2.1.5.1.2

Values

The current status of the FRU object in the slot.


•

1: other(1)

•

2: unknown(2)

•

3: on(3)

•

4: off(4)

•

5: faulty(5)


53-1001156-01

fruObjectNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.3

6 fruObjectNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.3

The slot number of the blade, and the unit number for everything else.


53-1001156-01

783

6 fruSupplierId 1.3.6.1.4.1.1588.2.1.2.1.5.1.4

fruSupplierId 1.3.6.1.4.1.1588.2.1.2.1.5.1.4

The supplier ID.


53-1001156-01

fruSupplierPartNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.5

6 fruSupplierPartNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.5

The supplier part number.


53-1001156-01

785

6 fruSupplierSerialNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.6

fruSupplierSerialNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.6

The supplier serial number.


53-1001156-01

fruSupplierRevCode 1.3.6.1.4.1.1588.2.1.2.1.5.1.7

6 fruSupplierRevCode 1.3.6.1.4.1.1588.2.1.2.1.5.1.7

The supplier revision code.


53-1001156-01

787

6

FRU History Table

FRU History Table

fruHistoryTable 1.3.6.1.4.1.1588.2.1.2.1.6

This table gives the contents of the entire history log of the FRU events.


53-1001156-01

fruHistoryEntry 1.3.6.1.4.1.1588.2.1.2.1.6.1

6 fruHistoryEntry 1.3.6.1.4.1.1588.2.1.2.1.6.1

Index

An entry in this table represents a particular FRU event.

fruHistoryIndex


53-1001156-01

789

6 fruHistoryIndex 1.3.6.1.4.1.1588.2.1.2.1.6.1.1

fruHistoryIndex 1.3.6.1.4.1.1588.2.1.2.1.6.1.1

Index of the FRU event in the history table.


53-1001156-01

fruHistoryClass 1.3.6.1.4.1.1588.2.1.2.1.6.1.2

6 fruHistoryClass 1.3.6.1.4.1.1588.2.1.2.1.6.1.2

Values

The type of the FRU object related to the event.


•

1: other(1)

•

2: unknown(2)

•

3: chassis(3)

•

4: cp(4)

•

5: other-CP(5)

•

6: switchblade(6)

•

7: wwn(7)

•

8: powerSupply(8)

•

9: fan(9)


53-1001156-01

791

6 fruHistoryObjectNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.3

fruHistoryObjectNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.3

The slot number of the blade and the unit number for everything else.


53-1001156-01

fruHistoryEvent 1.3.6.1.4.1.1588.2.1.2.1.6.1.4

6 fruHistoryEvent 1.3.6.1.4.1.1588.2.1.2.1.6.1.4

Values

The type of the FRU event.


•

1: added(1)

•

2: removed(2)

•

3: invalid(3)


53-1001156-01

793

6 fruHistoryTime 1.3.6.1.4.1.1588.2.1.2.1.6.1.5

fruHistoryTime 1.3.6.1.4.1.1588.2.1.2.1.6.1.5

The time at which this event happened.


53-1001156-01

fruHistoryFactoryPartNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.6

6 fruHistoryFactoryPartNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.6

The Brocade part number of the FRU object.


53-1001156-01

795

6 fruHistoryFactorySerialNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.7

fruHistoryFactorySerialNum 1.3.6.1.4.1.1588.2.1.2.1.6.1.7

The Brocade serial number of the FRU object.


53-1001156-01

CP Table

cpTable 1.3.6.1.4.1.1588.2.1.2.1.7

This table lists all the CPs in the system.

CP Table

6


53-1001156-01

797

6 cpEntry 1.3.6.1.4.1.1588.2.1.2.1.7.1

cpEntry 1.3.6.1.4.1.1588.2.1.2.1.7.1

Index

An entry represents a single CP in the system.

entPhysicalIndex


53-1001156-01

cpStatus 1.3.6.1.4.1.1588.2.1.2.1.7.1.1

Values

The current status of the CP.


•

1: other(1)

•

2: unknown(2)

•

3: active(3)

•

4: standby(4)

•

5: failed(5) cpStatus 1.3.6.1.4.1.1588.2.1.2.1.7.1.1

6


53-1001156-01

799

6 cpIpAddress 1.3.6.1.4.1.1588.2.1.2.1.7.1.2

cpIpAddress 1.3.6.1.4.1.1588.2.1.2.1.7.1.2

The IP address of the Ethernet interface of this CP.


53-1001156-01

cpIpMask 1.3.6.1.4.1.1588.2.1.2.1.7.1.3

6 cpIpMask 1.3.6.1.4.1.1588.2.1.2.1.7.1.3

The IP mask of the Ethernet interface of this CP.


53-1001156-01

801

6 cpIpGateway 1.3.6.1.4.1.1588.2.1.2.1.7.1.4

cpIpGateway 1.3.6.1.4.1.1588.2.1.2.1.7.1.4

The IP address of the IP gateway for this CP.


53-1001156-01

cpLastEvent 1.3.6.1.4.1.1588.2.1.2.1.7.1.5

Values

The last event related to this CP.


•

1: other(1)

•

2: unknown(2)

•

3: haSync(3)

•

4: haOutSync(4)

•

5: cpFaulty(5)

•

6: cpHealthy(6)

•

7: cpActive(7)

•

8: configChange(8)

•

9: failOverStart(9)

•

10: failOverDone(10)

•

11: firmwareCommit(11)

•

12: firmwareUpgrade(12)

HA-MIB Traps

This section lists the HA-MIB traps.

cpLastEvent 1.3.6.1.4.1.1588.2.1.2.1.7.1.5

6


53-1001156-01

803

6 fruStatusChanged 1.3.6.1.4.1.1588.2.1.2.2.0.1

fruStatusChanged 1.3.6.1.4.1.1588.2.1.2.2.0.1

Objects

Status

1: entPhysicalName

2: fruStatus

Current

This trap is sent when the status of any FRU object changes.


•

Enable or disable a FRU component

Sample trap output for Fabric OS v6.1.0; The following trap is generated when switch is rebooted: entPhysicalName.11 = MODULE 5 fruStatus.11 = off(4)


53-1001156-01

cpStatusChanged 1.3.6.1.4.1.1588.2.1.2.2.0.2

6 cpStatusChanged 1.3.6.1.4.1.1588.2.1.2.2.0.2

Objects

Status

1: cpStatus

2: cpLastEvent

3: swID

4: swSsn

Current

This trap is sent when the status of any CP object changes.

The cpLastEvent variable provides the information about the event that occurred.


•

Reboot

• firmwareDownload

Sample trap output for Fabric OS v4.4.0: cpStatus.13 = standby(4) cpLastEvent.13 = cpHealthy(6) swID.0 = 1 swSsn.0 = 10:00:00:60:69:e2:03:6d


53-1001156-01

805

6 fruHistoryTrap 1.3.6.1.4.1.1588.2.1.2.2.0.3

fruHistoryTrap 1.3.6.1.4.1.1588.2.1.2.2.0.3

Objects

Status

1: fruHistoryClass

2: fruHistoryObjectNum

3: fruHistoryEvent

4: fruHistoryTime

5: fruHistoryFactoryPartNum

6: fruHistoryFactorySerialNum

Current

This trap is generated when a FRU is added or removed.

Sample trap output for Fabric OS v4.4.0: fruHistoryClass.40 = powerSupply(8) fruHistoryObjectNum.40 = 2 fruHistoryEvent.40 = removed(2) fruHistoryTime.40 = Fri Aug 13 07:24:00 2004 fruHistoryFactoryPartNum.40 = 23-0000006-02 fruHistoryFactorySerialNum.40 = FL2L0022715

HA-MIB Traps and Sample Triggers

The following table lists the HA-MIB traps and sample events that will trigger them.

TABLE 18

HA-MIB Traps and Example Triggers

HA-MIB Traps Trigger fruStatusChanged cpStatusChanged fruHistoryTrap

Example events that will trigger this trap: switch reboot

Example events that will trigger this trap:

Reboot firmwareDownload

Example events that will trigger this trap:

Add or remove a FRU component


53-1001156-01

FICON MIB Objects

Chapter

7

This chapter provides descriptions and other information specific to FICON MIB

(LINK-INCIDENT-MIB) object types, including the following information:

•

FICON MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 807

•

ficonRNID Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 811

•

ficonLIRR Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841

•

ficonRLIR Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 851

•

linkIncidentMIBTraps Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 867

FICON MIB Overview

The FICON MIB module (LINK-INCIDENT-MIB) defines support for FICON in Fabric OS v4.1.2 and later. This MIB addresses link incident and link failure data for FICON hosts and devices connected to a Brocade switch.

The descriptions of each of the MIB variables in this chapter come directly from the FICON MIB itself.

The object types in the FICON MIB are organized into the following groupings:

•

Request Node Identification Data (RNID)

•

Link Incident Record Registration (LIRR)

•

Registered Link Incident Report (RLIR)

•

Traps

SNMP Traps for FICON

SNMP traps for FICON are generated when:

• a FICON device is added to the switch

• a FICON device is removed from the switch

• a new “listener” is added (once the LIRR handshake is complete)

• a “listener” entry is deleted

• a link incident occurs

FICON MIB System Organization of MIB Objects

Figure 54 and

Figure 56 depict the organization and structure of the FICON MIB file system.

- iso

- org

- dod


53-1001156-01

807

808

7

FICON MIB Overview

- internet

- private

- enterprises

- bsci

- commDev

- fibreChannel

- fcSwitch

- linkIncidentMIB

- ficonRNID

- ficonLIRR

- ficonRLIR

- linkIncidentMIBTraps

FIGURE 54

Overall Tree Structure for FICON MIB (linkIncidentMIB)

- linkIncidentMIB

- ficonRNID

- nodeRNIDTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.2.1

- nodeRNIDTable 1.3.6.1.4.1.1588.2.1.1.50.2.2

- nodeRNIDEntry 1.3.6.1.4.1.1588.2.1.1.50.2.2.1

- nodeRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.1

- nodeRNIDIncidentPortWWN 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.2

- nodeRNIDPID 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.3

- nodeRNIDFlags 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.4

- nodeRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.5

- nodeRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.6

- nodeRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.7

- nodeRNIDManufacturerPlant 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.8

- nodeRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.9

- nodeRNIDConnectedPortWWN 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.10

- nodeRNIDPortType 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.11

- nodeRNIDFormat 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.12

- nodeRNIDTag 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.13

- nodeRNIDParams 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.14

- switchRNIDTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.2.3

- switchRNIDTable 1.3.6.1.4.1.1588.2.1.1.50.2.4

- switchRNIDEntry 1.3.6.1.4.1.1588.2.1.1.50.2.4.1

- switchRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.1

- switchRNIDSwitchWWN 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.2

- switchRNIDFlags 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.3

- switchRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.4

- switchRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.5

- switchRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.6

- switchRNIDManufacturerPlant 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.7

- switchRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.8

- switchRNIDTag 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.9

- ficonLIRR

- switchRNIDParams 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.10

- LIRRTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.3.1

- LIRRTable 1.3.6.1.4.1.1588.2.1.1.50.3.2

- LIRREntry 1.3.6.1.4.1.1588.2.1.1.50.3.2.1

- LIRRIndex 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.1

- LIRRListenerPortWWN 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.2

- LIRRListenerPID 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.3

- LIRRRegType 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.4

- LIRRProtocol 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.5

- LIRRPortType 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.6

- LIRRFormat 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.7

- ficonRLIR

- rLIRTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.4.1


53-1001156-01


53-1001156-01

FICON MIB Overview

7

- rLIRTable 1.3.6.1.4.1.1588.2.1.1.50.4.2

- rLIREntry 1.3.6.1.4.1.1588.2.1.1.50.4.2.1

- rLIRIndex 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.1

- rLIRIncidentPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.2

- rLIRIncidentNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.3

- rLIRIncidentPortType 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.5

- rLIRIncidentPID 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.6

- rLIRIncidentPortNumber 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.7

- rLIRConnectedPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.8

- rLIRConnectedNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.9

- rLIRFabricWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.10

- rLIRLinkFailureType 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.11

- rLIRTimeStamp 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.12

- rLIRFormat 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.13

FIGURE 55

linkIncidentMIB Hierarchy

- linkIncidentMIBTraps

- linkIncidentMIBTrapPrefix

- linkRNIDDeviceRegistration 1.3.6.1.4.1.1588.2.1.1.50.21.0.1

- linkRNIDDeviceDeRegistration 1.3.6.1.4.1.1588.2.1.1.50.21.0.2

- linkLIRRListenerAdded 1.3.6.1.4.1.1588.2.1.1.50.21.0.3

- linkLIRRListenerRemoved 1.3.6.1.4.1.1588.2.1.1.50.21.0.4

- linkRLIRFailureIncident 1.3.6.1.4.1.1588.2.1.1.50.21.0.5

FIGURE 56

linkIncidentMIBTraps Hierarchy

Textual Conventions

Table 19 lists the textual conventions for the FICON MIB.

TABLE 19

FICON MIB Textual Conventions

Name Status Description

LIRRProtocol

FcPortID

RNIDModel

RLIRLinkFailureType

RNIDManufacturer

Current

Current

Current

Current

Current

Syntax

Represents the LIRR Protocol. INTEGER {

fcp (1),

sb2 (2)

}

OCTET STRING (SIZE (3)) Represents Fibre Channel

Address ID, a 24-bit value unique within the address space of a fabric.

Represents the value of

Model Number.

Represents the link failure type.

OCTET STRING (SIZE (3))

Represents the Manufacturer name or code.

INTEGER {

bitErrorRate(2),

lossOfSignal(3),

nOSRecognized(4),

primitiveSequenceTimeout(5),

invalidSeqForPortState(6),

loopInitializationTimeout(7),

lossOfSignalInLoopInit(8)

}


809

810

7

FICON MIB Overview

TABLE 19

FICON MIB Textual Conventions (Continued)

Name

RNIDTagType

LinkWwn

RegType

RNIDSequenceNumber

RNIDManufacturerPlant

RNIDParams

PortType

RNIDFlags

LinkFormat

RNIDType

Status

Current

Current

Current

Current

Current

Current

Current

Current

Current

Current

Description Syntax

Represents the value of RNID

Tag, in hexadecimal format.

Note: Includes DISPLAY-HINT

“x”.

Represents the link WWN.

Represents the RNID

Registration Type.



INTEGER {

conditional (1),

unconditional (2)

}

OCTET STRING (SIZE (12)) Sequence number of the self describing node.

Represents the manufacturer plant name or code.


Represents the value of

Param.

Represents the Port Type.


Represents the value of RNID

Flag in hexadecimal format. It indicates if the node is valid, not valid, or not current.

Represents the frame format.

INTEGER {

ficon (1),

common (2)

}

OCTET STRING (SIZE (6)) Represents the value of Type

Number. Displays the type number of the self-describing node. It also describes the machine type.

INTEGER {

n-port (1),

nl-port (2)

}



53-1001156-01

ficonRNID Group

7

ficonRNID Group

This group contains all Request Node Identification Data (RNID) group objects for FICON.


53-1001156-01

811

7 nodeRNIDTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.2.1

nodeRNIDTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.2.1

The number of entries in Request Node Identification Data (RNID) table.

Refer to the Fabric OS Command Reference and the ficonShow command for additional information on FICON MIB tables.


53-1001156-01

nodeRNIDTable 1.3.6.1.4.1.1588.2.1.1.50.2.2

7 nodeRNIDTable 1.3.6.1.4.1.1588.2.1.1.50.2.2

A table that contains one entry for each FICON RNID node attached to a switch.


53-1001156-01

813

7 nodeRNIDEntry 1.3.6.1.4.1.1588.2.1.1.50.2.2.1

nodeRNIDEntry 1.3.6.1.4.1.1588.2.1.1.50.2.2.1

Index

A entry containing the RNID information for a FICON node.

nodeRNIDIndex


53-1001156-01

nodeRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.1

7 nodeRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.1

Index into the nodeRNIDTable.


53-1001156-01

815

7 nodeRNIDIncidentPortWWN 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.2

nodeRNIDIncidentPortWWN 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.2

Port WWN for Incident port. An N_Port (FICON device or host) is an incident port.


53-1001156-01

nodeRNIDPID 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.3

7 nodeRNIDPID 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.3

PID for an Incident port.


53-1001156-01

817

7 nodeRNIDFlags 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.4

nodeRNIDFlags 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.4

RNID flags for an Incident port. Bits 0–2 of the flag describe the validity of bits 3–7 of the flag. Bit 3 of the flag specifies whether the node is a device-type node or a central-processor-complex-type

(CPC-type) node. Bits 4–7 of the flag are reserved.


53-1001156-01

nodeRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.5

7 nodeRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.5

Number associated with a node.


53-1001156-01

819

7 nodeRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.6

nodeRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.6

Model number of the RNID node.


53-1001156-01

nodeRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.7

7 nodeRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.7

Identifies the manufacturer of the node.


53-1001156-01

821

7 nodeRNIDManufacturerPlant 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.8

nodeRNIDManufacturerPlant 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.8

Identifies the manufacturer plant of the node.


53-1001156-01

nodeRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.9

7 nodeRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.9

Identifies the sequence number of the node.


53-1001156-01

823

7 nodeRNIDConnectedPortWWN 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.10

nodeRNIDConnectedPortWWN 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.10

WWN of the connected port.


53-1001156-01

nodeRNIDPortType 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.11

7 nodeRNIDPortType 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.11

Port type (N, NL, or virtual port) of the connected port.


53-1001156-01

825

7 nodeRNIDFormat 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.12

nodeRNIDFormat 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.12

Node identification data format of the connected port.


53-1001156-01

nodeRNIDTag 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.13

7 nodeRNIDTag 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.13

Node identification tag of the connected port.


53-1001156-01

827

7 nodeRNIDParams 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.14

nodeRNIDParams 1.3.6.1.4.1.1588.2.1.1.50.2.2.1.14

Node parameters of the connected port.


53-1001156-01

switchRNIDTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.2.3

7 switchRNIDTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.2.3

The number of entries in an RNID table that corresponds to the switch.



53-1001156-01

829

7 switchRNIDTable 1.3.6.1.4.1.1588.2.1.1.50.2.4

switchRNIDTable 1.3.6.1.4.1.1588.2.1.1.50.2.4

A table that contains RNID information for each switch FICON node.


53-1001156-01

switchRNIDEntry 1.3.6.1.4.1.1588.2.1.1.50.2.4.1

7 switchRNIDEntry 1.3.6.1.4.1.1588.2.1.1.50.2.4.1

An entry containing the RNID information for the switch FICON node.


53-1001156-01

831

7 switchRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.1

switchRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.1

Index into switchRNIDTable.


53-1001156-01

switchRNIDSwitchWWN 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.2

7 switchRNIDSwitchWWN 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.2

WWN of the switch.


53-1001156-01

833

7 switchRNIDFlags 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.3

switchRNIDFlags 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.3

RNID flags for the switch.


53-1001156-01

switchRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.4

7 switchRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.4

Type Number associated with the switch.


53-1001156-01

835

7 switchRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.5

switchRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.5

Model number of the RNID switch.


53-1001156-01

switchRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.6

7 switchRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.6

Identifies the manufacturer of the switch.


53-1001156-01

837

7 switchRNIDManufacturerPlant 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.7

switchRNIDManufacturerPlant 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.7

Identifies the manufacturer plant of the switch.


53-1001156-01

switchRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.8

7 switchRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.8

Identifies the sequence number of the switch.


53-1001156-01

839

7 switchRNIDTag 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.9

switchRNIDTag 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.9

Identification tag of the switch.


53-1001156-01

switchRNIDParams 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.10

7 switchRNIDParams 1.3.6.1.4.1.1588.2.1.1.50.2.4.1.10

Identifies the parameters of the switch.

ficonLIRR Group

This group contains all Link Incident Record Registration (LIRR) group objects for FICON.


53-1001156-01

841

7

LIRRTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.3.1

LIRRTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.3.1

The number of entries in an LIRR table.



53-1001156-01

LIRRTable 1.3.6.1.4.1.1588.2.1.1.50.3.2

LIRRTable 1.3.6.1.4.1.1588.2.1.1.50.3.2

A table that contains LIRR information, one entry for each LIRR incident for an attached FICON device.

7


53-1001156-01

843

7

LIRREntry 1.3.6.1.4.1.1588.2.1.1.50.3.2.1

LIRREntry 1.3.6.1.4.1.1588.2.1.1.50.3.2.1

An entry containing LIRR information.


53-1001156-01

LIRRIndex 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.1

Index into the LIRR table.

LIRRIndex 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.1

7


53-1001156-01

845

7

LIRRListenerPortWWN 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.2

LIRRListenerPortWWN 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.2

WWN of the Listener port.


53-1001156-01

LIRRListenerPID 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.3

7

LIRRListenerPID 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.3

PID for the Listener port.


53-1001156-01

847

7

LIRRRegType 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.4

LIRRRegType 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.4

Registration type: conditional or unconditional.


53-1001156-01

LIRRProtocol 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.5

7

LIRRProtocol 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.5

Protocol type supported.


53-1001156-01

849

7

LIRRPortType 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.6

LIRRPortType 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.6

Attached port type.


53-1001156-01

LIRRFormat 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.7

7

LIRRFormat 1.3.6.1.4.1.1588.2.1.1.50.3.2.1.7

Registration type: conditional or unconditional.

ficonRLIR Group

This group contains all Registered Link Incident Report (RLIR) group objects for FICON.


53-1001156-01

851

7 rLIRTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.4.1

rLIRTableNumEntries 1.3.6.1.4.1.1588.2.1.1.50.4.1

The number of entries in a switch RLIR table.



53-1001156-01

rLIRTable 1.3.6.1.4.1.1588.2.1.1.50.4.2

rLIRTable 1.3.6.1.4.1.1588.2.1.1.50.4.2

A table that contains RLIR information, one entry for each LIRR incident for an attached FICON device.

7


53-1001156-01

853

7 rLIREntry 1.3.6.1.4.1.1588.2.1.1.50.4.2.1

rLIREntry 1.3.6.1.4.1.1588.2.1.1.50.4.2.1

An entry containing RLIR information.


53-1001156-01

rLIRIndex 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.1

Index into the RLIR table.

rLIRIndex 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.1

7


53-1001156-01

855

7 rLIRIncidentPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.2

rLIRIncidentPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.2

Port WWN for RLIR Incident port.


53-1001156-01

rLIRIncidentNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.3

7 rLIRIncidentNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.3

Incident node WWN.


53-1001156-01

857

7 rLIRIncidentPortType 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.5

rLIRIncidentPortType 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.5

RLIR Incident port type.


53-1001156-01

rLIRIncidentPID 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.6

7 rLIRIncidentPID 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.6

RLIR Incident PID.


53-1001156-01

859

7 rLIRIncidentPortNumber 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.7

rLIRIncidentPortNumber 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.7

RLIR Incident port number. This is a vendor-specific port number.


53-1001156-01

rLIRConnectedPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.8

7 rLIRConnectedPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.8

RLIR Connected port WWN.


53-1001156-01

861

7 rLIRConnectedNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.9

rLIRConnectedNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.9

RLIR Connected node WWN.


53-1001156-01

rLIRFabricWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.10

7 rLIRFabricWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.10

RLIR Fabric WWN.


53-1001156-01

863

7 rLIRLinkFailureType 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.11

rLIRLinkFailureType 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.11

RLIR Link failure type.


53-1001156-01

rLIRTimeStamp 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.12

7 rLIRTimeStamp 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.12

RLIR time stamp.


53-1001156-01

865

7 rLIRFormat 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.13

rLIRFormat 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.13

RLIR Format.


53-1001156-01

linkIncidentMIBTraps Group

7

linkIncidentMIBTraps Group

linkIncidentMIBTrapPrefix 1.3.6.1.4.1.1588.2.1.1.50.21.0

The Link Incident traps.


53-1001156-01

867

7 linkRNIDDeviceRegistration 1.3.6.1.4.1.1588.2.1.1.50.21.0.1

linkRNIDDeviceRegistration 1.3.6.1.4.1.1588.2.1.1.50.21.0.1

Objects

A device registered with the switch.

1: nodeRNIDIndex

2: nodeRNIDIncidentPortWWN

3: nodeRNIDConnectedPortWWN


53-1001156-01

linkRNIDDeviceDeRegistration 1.3.6.1.4.1.1588.2.1.1.50.21.0.2

7 linkRNIDDeviceDeRegistration 1.3.6.1.4.1.1588.2.1.1.50.21.0.2

Objects

A device deregistered with the switch.

1: nodeRNIDIndex

2: nodeRNIDIncidentPortWWN

3: nodeRNIDConnectedPortWWN


53-1001156-01

869

7 linkLIRRListenerAdded 1.3.6.1.4.1.1588.2.1.1.50.21.0.3

linkLIRRListenerAdded 1.3.6.1.4.1.1588.2.1.1.50.21.0.3

Objects

A listener for link failure incident is added.

1: lIRRListenerPortWWN

2: lIRRListenerPID

3: lIRRIndex


53-1001156-01

linkLIRRListenerRemoved 1.3.6.1.4.1.1588.2.1.1.50.21.0.4

7 linkLIRRListenerRemoved 1.3.6.1.4.1.1588.2.1.1.50.21.0.4

Objects

A listener for link failure incident was removed.

1: lIRRListenerPortWWN

2: lIRRListenerPID

3: lIRRIndex


53-1001156-01

871

7 linkRLIRFailureIncident 1.3.6.1.4.1.1588.2.1.1.50.21.0.5

linkRLIRFailureIncident 1.3.6.1.4.1.1588.2.1.1.50.21.0.5

Objects

A link failure incident has occurred. The value of lIRRIndex will be -2147483647 and

IIRRListenerPID will be 0, if there is no listener for incident.

1: nodeRNIDIndex

2: lIRRIndex

3: rLIRIncidentPortWwn

4: rLIRConnectedPortWwn

5: rLIRIndex

6: rLIRLinkFailureType

7: lIRRListenerPID


53-1001156-01

FibreAlliance MIB Objects

Chapter

8

This chapter contains descriptions and other information specific to FibreAlliance MIB

(FCMGMT-MIB) object types, including the following:

•

FibreAlliance MIB Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873

•

ConnSet Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881

•

Statistics Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982

•

Service Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1034

•

SNMP Trap Registration Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053

•

Revision Number Scalar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1061

•

Unsupported Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1061

•

FibreAlliance MIB Traps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1062

FibreAlliance MIB Overview

The descriptions of each of the MIB variables in this chapter come directly from the FCMGMT-MIB itself. The notes that follow the descriptions typically pertain to Brocade-specific information and are provided by Brocade.

The object types in FCMGMT-MIB are organized into the following groups:

•

Connectivity

•

Trap Registration

•

Revision Number

•

Statistic Set

•

Service Set


53-1001156-01

873

874

8


FCMGMT-MIB System Organization of MIB Objects

Figure 57 to

Figure 67

depicts the high level organization of the FCMGMT-MIB.

- iso

- org

- dod

- internet

- experimental

- fcmgmt

- connSet

- uNumber 1.3.6.1.3.94.1.1

- systemURL 1.3.6.1.3.94.1.2

+ connUnitTable 1.3.6.1.3.94.1.6

+ connUnitRevsTable 1.3.6.1.3.94.1.7

+ connUnitSensorTable 1.3.6.1.3.94.1.8

+ connUnitPortTable 1.3.6.1.3.94.1.10

+ connUnitEventTable 1.3.6.1.3.94.1.11

+ connUnitLinkTable 1.3.6.1.3.94.1.12

- trapReg

- trapMaxClients 1.3.6.1.3.94.2.1

- trapClientCount 1.3.6.1.3.94.2.2

+ trapRegTable 1.3.6.1.3.94.2.3

- revisionNumber 1.3.6.1.3.94.3

- statSet

+ connUnitPortStatTable 1.3.6.1.3.94.4.5

- connUnitServiceSet

+ connUnitServiceScalars 1.3.6.1.3.94.5.1

+ connUnitServiceTables 1.3.6.1.3.94.5.2


53-1001156-01


53-1001156-01


8

FIGURE 57

FCMGMT-MIB High Level Hierarchy

- connUnitTable 1.3.6.1.3.94.1.6

- connUnitEntry 1.3.6.1.3.94.1.6.1

- connUnitId 1.3.6.1.3.94.1.6.1.1

- connUnitGlobalId 1.3.6.1.3.94.1.6.1.2

- connUnitType 1.3.6.1.3.94.1.6.1.3

- connUnitNumports 1.3.6.1.3.94.1.6.1.4

- connUnitState 1.3.6.1.3.94.1.6.1.5

- connUnitStatus 1.3.6.1.3.94.1.6.1.6

- connUnitProduct 1.3.6.1.3.94.1.6.1.7

- connUnitSn 1.3.6.1.3.94.1.6.1.8

- connUnitUpTime 1.3.6.1.3.94.1.6.1.9

- connUnitUrl 1.3.6.1.3.94.1.6.1.10

- connUnitDomainId 1.3.6.1.3.94.1.6.1.11

- connUnitProxyMaster 1.3.6.1.3.94.1.6.1.12

- connUnitPrincipal 1.3.6.1.3.94.1.6.1.13

- connUnitNumSensors 1.3.6.1.3.94.1.6.1.14

- connUnitStatusChangeTime 1.3.6.1.3.94.1.6.1.15

- connUnitConfigurationChangeTime 1.3.6.1.3.94.1.6.1.16

- connUnitNumRevs 1.3.6.1.3.94.1.6.1.17

- connUnitNumZones 1.3.6.1.3.94.1.6.1.18

- connUnitModuleId 1.3.6.1.3.94.1.6.1.19

- connUnitName 1.3.6.1.3.94.1.6.1.20

- connUnitInfo 1.3.6.1.3.94.1.6.1.21

- connUnitControl 1.3.6.1.3.94.1.6.1.22

- connUnitContact 1.3.6.1.3.94.1.6.1.23

- connUnitLocation 1.3.6.1.3.94.1.6.1.24

- connUnitEventFilter 1.3.6.1.3.94.1.6.1.25

- connUnitNumEvents 1.3.6.1.3.94.1.6.1.26

- connUnitMaxEvents 1.3.6.1.3.94.1.6.1.27

- connUnitEventCurrID 1.3.6.1.3.94.1.6.1.28

FIGURE 58

ConnUnitTable Hierarchy

- connUnitRevsTable 1.3.6.1.3.94.1.7

- connUnitRevsEntry 1.3.6.1.3.94.1.7.1

- connUnitRevsUnitId 1.3.6.1.3.94.1.7.1.1

- connUnitRevsIndex 1.3.6.1.3.94.1.7.1.2

- connUnitRevsRevId 1.3.6.1.3.94.1.7.1.3

- connUnitRevsDescription 1.3.6.1.3.94.1.7.1.4

FIGURE 59

ConnUnitRevsTable Hierarchy

- connUnitSensorTable 1.3.6.1.3.94.1.8

- connUnitSensorEntry 1.3.6.1.3.94.1.8.1

- connUnitSensorUnitId 1.3.6.1.3.94.1.8.1.1

- connUnitSensorIndex 1.3.6.1.3.94.1.8.1.2

- connUnitSensorName 1.3.6.1.3.94.1.8.1.3

- connUnitSensorStatus 1.3.6.1.3.94.1.8.1.4

- connUnitSensorInfo 1.3.6.1.3.94.1.8.1.5

- connUnitSensorMessage 1.3.6.1.3.94.1.8.1.6

- connUnitSensorType 1.3.6.1.3.94.1.8.1.7

- connUnitSensorCharacteristic 1.3.6.1.3.94.1.8.1.8

FIGURE 60

ConnUnitSensorTable Hierarchy

875

876

8


- connUnitPortTable 1.3.6.1.3.94.1.10

- connUnitPortEntry 1.3.6.1.3.94.1.10.1

- connUnitPortUnitId 1.3.6.1.3.94.1.10.1.1

- connUnitPortIndex 1.3.6.1.3.94.1.10.1.2

- connUnitPortType 1.3.6.1.3.94.1.10.1.3

- connUnitPortFCClassCap 1.3.6.1.3.94.1.10.1.4

- connUnitPortFCClassOp 1.3.6.1.3.94.1.10.1.5

- connUnitPortState 1.3.6.1.3.94.1.10.1.6

- connUnitPortStatus 1.3.6.1.3.94.1.10.1.7

- connUnitPortTransmitterType 1.3.6.1.3.94.1.10.1.8

- connUnitPortModuleType 1.3.6.1.3.94.1.10.1.9

- connUnitPortWwn 1.3.6.1.3.94.1.10.1.10

- connUnitPortFCId 1.3.6.1.3.94.1.10.1.11

- connUnitPortSn 1.3.6.1.3.94.1.10.1.12

- connUnitPortRevision 1.3.6.1.3.94.1.10.1.13

- connUnitPortVendor 1.3.6.1.3.94.1.10.1.14

- connUnitPortSpeed 1.3.6.1.3.94.1.10.1.15

- connUnitPortControl 1.3.6.1.3.94.1.10.1.16

- connUnitPortName 1.3.6.1.3.94.1.10.1.17

- connUnitPortPhysicalNumber 1.3.6.1.3.94.1.10.1.18

- connUnitPortStatObject 1.3.6.1.3.94.1.10.1.19

- connUnitPortProtocolCap 1.3.6.1.3.94.1.10.1.20

- connUnitPortProtocolOp 1.3.6.1.3.94.1.10.1.21

- connUnitPortNodeWwn 1.3.6.1.3.94.1.10.1.22

- connUnitPortHWState 1.3.6.1.3.94.1.10.1.23

FIGURE 61

ConnUnitPortTable Hierarchy

- connUnitEventTable 1.3.6.1.3.94.1.11

- connUnitEventEntry 1.3.6.1.3.94.1.11.1

- connUnitEventUnitId 1.3.6.1.3.94.1.11.1.1

- connUnitEventIndex 1.3.6.1.3.94.1.11.1.2

- connUnitEventId 1.3.6.1.3.94.1.11.1.3

- connUnitREventTime 1.3.6.1.3.94.1.11.1.4

- connUnitSEventTime 1.3.6.1.3.94.1.11.1.5

- connUnitEventSeverity 1.3.6.1.3.94.1.11.1.6

- connUnitEventType 1.3.6.1.3.94.1.11.1.7

- connUnitEventObject 1.3.6.1.3.94.1.11.1.8

- connUnitEventDescr 1.3.6.1.3.94.1.11.1.9

FIGURE 62

ConnUnitEventTable Hierarchy


53-1001156-01


53-1001156-01


8

- connUnitLinkTable 1.3.6.1.3.94.1.12

- connUnitLinkEntry 1.3.6.1.3.94.1.12.1

- connUnitLinkUnitId 1.3.6.1.3.94.1.12.1.1

- connUnitLinkIndex 1.3.6.1.3.94.1.12.1.2

- connUnitLinkNodeIdX 1.3.6.1.3.94.1.12.1.3

- connUnitLinkPortNumberX 1.3.6.1.3.94.1.12.1.4

- connUnitLinkPortWwnX 1.3.6.1.3.94.1.12.1.5

- connUnitLinkNodeIdY 1.3.6.1.3.94.1.12.1.6

- connUnitLinkPortNumberY 1.3.6.1.3.94.1.12.1.7

- connUnitLinkPortWwnY 1.3.6.1.3.94.1.12.1.8

- connUnitLinkAgentAddressY 1.3.6.1.3.94.1.12.1.9

- connUnitLinkAgentAddressTypeY 1.3.6.1.3.94.1.12.1.10

- connUnitLinkAgentPortY 1.3.6.1.3.94.1.12.1.11

- connUnitLinkUnitTypeY 1.3.6.1.3.94.1.12.1.12

- connUnitLinkConnIdY 1.3.6.1.3.94.1.12.1.13

- connUnitLinkCurrIndex 1.3.6.1.3.94.1.12.1.14

FIGURE 63

ConnUnitLinkTable Hierarchy

- trapRegTable 1.3.6.1.3.94.2.3

- trapRegEntry 1.3.6.1.3.94.2.3.1

- trapRegIpAddress 1.3.6.1.3.94.2.3.1.1

- trapRegPort 1.3.6.1.3.94.2.3.1.2

- trapRegFilter 1.3.6.1.3.94.2.3.1.3

- trapRegRowState 1.3.6.1.3.94.2.3.1.4

FIGURE 64

TrapRegTable Hierarchy

877

878

8


- connUnitPortStatTable 1.3.6.1.3.94.4.5

- connUnitPortStatEntry 1.3.6.1.3.94.4.5.1

- connUnitPortStatUnitId 1.3.6.1.3.94.4.5.1.1

- connUnitPortStatIndex 1.3.6.1.3.94.4.5.1.2

- connUnitPortStatCountError 1.3.6.1.3.94.4.5.1.3

- connUnitPortStatCountTxObjects 1.3.6.1.3.94.4.5.1.4

- connUnitPortStatCountRxObjects 1.3.6.1.3.94.4.5.1.5

- connUnitPortStatCountTxElements 1.3.6.1.3.94.4.5.1.6

- connUnitPortStatCountRxElements 1.3.6.1.3.94.4.5.1.7

- connUnitPortStatCountBBCreditZero 1.3.6.1.3.94.4.5.1.8

- connUnitPortStatCountInputBuffersFull 1.3.6.1.3.94.4.5.1.9

- connUnitPortStatCountFBSYFrames 1.3.6.1.3.94.4.5.1.10

- connUnitPortStatCountPBSYFrames 1.3.6.1.3.94.4.5.1.11

- connUnitPortStatCountFRJTFrames 1.3.6.1.3.94.4.5.1.12

- connUnitPortStatCountPRJTFrames 1.3.6.1.3.94.4.5.1.13

- connUnitPortStatCountClass1RxFrames 1.3.6.1.3.94.4.5.1.14

- connUnitPortStatCountClass1TxFrames 1.3.6.1.3.94.4.5.1.15

- connUnitPortStatCountClass1FBSYFrames 1.3.6.1.3.94.4.5.1.16

- connUnitPortStatCountClass1PBSYFrames 1.3.6.1.3.94.4.5.1.17

- connUnitPortStatCountClass1FRJTFrames 1.3.6.1.3.94.4.5.1.18

- connUnitPortStatCountClass1PRJTFrames 1.3.6.1.3.94.4.5.1.19



- connUnitPortStatCountClass2FBSYFrames 1.3.6.1.3.94.4.5.1.22

- connUnitPortStatCountClass2PBSYFrames 1.3.6.1.3.94.4.5.1.23

- connUnitPortStatCountClass2FRJTFrames 1.3.6.1.3.94.4.5.1.24

- connUnitPortStatCountClass2PRJTFrames 1.3.6.1.3.94.4.5.1.25



- connUnitPortStatCountClass3Discards 1.3.6.1.3.94.4.5.1.28

- connUnitPortStatCountRxMulticastObjects 1.3.6.1.3.94.4.5.1.29

- connUnitPortStatCountTxMulticastObjects 1.3.6.1.3.94.4.5.1.30

- connUnitPortStatCountRxBroadcastObjects 1.3.6.1.3.94.4.5.1.31

- connUnitPortStatCountTxBroadcastObjects 1.3.6.1.3.94.4.5.1.32

- connUnitPortStatCountRxLinkResets 1.3.6.1.3.94.4.5.1.33

- connUnitPortStatCountTxLinkResets 1.3.6.1.3.94.4.5.1.34

- connUnitPortStatCountNumberLinkResets 1.3.6.1.3.94.4.5.1.35

- connUnitPortStatCountRxOfflineSequences 1.3.6.1.3.94.4.5.1.36

- connUnitPortStatCountTxOfflineSequences 1.3.6.1.3.94.4.5.1.37

- connUnitPortStatCountNumberOfflineSequences 1.3.6.1.3.94.4.5.1.38

- connUnitPortStatCountLinkFailures 1.3.6.1.3.94.4.5.1.39

- connUnitPortStatCountInvalidCRC 1.3.6.1.3.94.4.5.1.40

- connUnitPortStatCountInvalidTxWords 1.3.6.1.3.94.4.5.1.41

- connUnitPortStatCountPrimitiveSequenceProtocolErrors

1.3.6.1.3.94.4.5.1.42

- connUnitPortStatCountLossofSignal 1.3.6.1.3.94.4.5.1.43

- connUnitPortStatCountLossofSynchronization 1.3.6.1.3.94.4.5.1.44

- connUnitPortStatCountInvalidOrderedSets 1.3.6.1.3.94.4.5.1.45

- connUnitPortStatCountFramesTooLong 1.3.6.1.3.94.4.5.1.46

- connUnitPortStatCountFramesTruncated 1.3.6.1.3.94.4.5.1.47

- connUnitPortStatCountAddressErrors 1.3.6.1.3.94.4.5.1.48

- connUnitPortStatCountDelimiterErrors 1.3.6.1.3.94.4.5.1.49

- connUnitPortStatCountEncodingDisparityErrors 1.3.6.1.3.94.4.5.1.50

FIGURE 65

ConnUnitPortStatTable Hierarchy


53-1001156-01


8


- connUnitServiceScalars

- connUnitSnsMaxEntry 1.3.6.1.3.94.5.1.1

FIGURE 66

ConnUnitServiceScalars Hierarchy


- connUnitServiceTables

- connUnitSnsTable 1.3.6.1.3.94.5.2.1

- connUnitSnsEntry 1.3.6.1.3.94.5.2.1.1

- connUnitSnsId 1.3.6.1.3.94.5.2.1.1.1

- connUnitSnsPortIndex 1.3.6.1.3.94.5.2.1.1.2

- connUnitSnsPortIdentifier 1.3.6.1.3.94.5.2.1.1.3

- connUnitSnsPortName 1.3.6.1.3.94.5.2.1.1.4

- connUnitSnsNodeName 1.3.6.1.3.94.5.2.1.1.5

- connUnitSnsClassOfSvc 1.3.6.1.3.94.5.2.1.1.6

- connUnitSnsNodeIPAddress 1.3.6.1.3.94.5.2.1.1.7

- connUnitSnsProcAssoc 1.3.6.1.3.94.5.2.1.1.8

- connUnitSnsFC4Type 1.3.6.1.3.94.5.2.1.1.9

- connUnitSnsPortType 1.3.6.1.3.94.5.2.1.1.10

- connUnitSnsPortIPAddress 1.3.6.1.3.94.5.2.1.1.11

- connUnitSnsFabricPortName 1.3.6.1.3.94.5.2.1.1.12

- connUnitSnsHardAddress 1.3.6.1.3.94.5.2.1.1.13

- connUnitSnsSymbolicPortName 1.3.6.1.3.94.5.2.1.1.14

- connUnitSnsSymbolicNodeName 1.3.6.1.3.94.5.2.1.1.15

FIGURE 67

ConnUnitSnsTable Hierarchy

Definitions for FCMGMT-MIB

The following definitions are used for FCMGMT-MIB.

TABLE 20


Type Definition

FcNameId

FcGlobalId

FcAddressId

Value Description

Octet String of size 8 The Port Name for this entry in the SNS table.

Octet String of size

16

An optional global-scope identifier for this connectivity unit. It MUST be a WWN for this connectivity unit or 16 octets of value zero.

Octet String of size 3 The Port Identifier for this entry in the SNS table.


53-1001156-01

879

8


TABLE 20


Type Definition

FcEventSeverity

Value

Integer

FcUnitType Integer

Description

1 (unknown)

2 (emergency) Emergency status.

3 (alert) Alert status.

4 (critical) Critical status.

5 (error) Error status.

6 (warning) Warning status.

7 (notify) Notification status.

8 (info) Informational status.

9 (debug) Debug status.

10 (mark) All messages logged.

1 (unknown)

2 (other) None of 3–14.

3 (hub) Passive connectivity unit supporting loop protocol.

4 (switch) Active connectivity unit supporting multiple protocols.

5 (gateway) Unit that not only converts the interface but also encapsulates the frame into another protocol. The assumption is that there are always two gateways connected together: for example, FC <-> ATM.

6 (converter) Unit that converts from one interface to another: for example, FC <-> SCSI.

7 (hba) Host bus adapter.

8 (proxy-agent) Software proxy agent.

9 (storage-device) Disk, CD, tape, and so on.

10 (host) Host computer.

11 (storage-subsystem) For example, RAID, library.

12 (module) Subcomponent of a system.

13 (swdriver) Software driver.

14 (storage-access-device) Provides storage management and access for heterogeneous hosts and heterogeneous devices.


53-1001156-01

ConnSet Group

Implementation of the Connectivity group is mandatory for all systems.

ConnSet Group

8


53-1001156-01

881

8 uNumber 1.3.6.1.3.94.1.1

uNumber 1.3.6.1.3.94.1.1

The number of connectivity units present on this system (represented by this agent). Might be a count of the boards in a chassis or the number of full boxes in a rack.

The connectivity unit is mapped to a switch. uNumber is always set to 1.


53-1001156-01

systemURL 1.3.6.1.3.94.1.2

8 systemURL 1.3.6.1.3.94.1.2

The top-level URL of the system; if it does not exist, the value is an empty string. The URL format is implementation dependant and can have keywords embedded that are preceded by a percent sign

(for example, %USER).

The following are the defined keywords that are recognized and replaced with data during a launch.

USER Replace with username

PASSWORD Replace with password

GLOBALID Replace with global ID

SERIALNO Replace with serial number

The expected value for system URL.0 is: http://{a.b.c.d} where {a.b.c.d} is the IP address of the switch if a Web Tools license is available.

“” (null) where “” is used when a Web Tools license is not available.


53-1001156-01

883

8 connUnitTable 1.3.6.1.3.94.1.6

connUnitTable 1.3.6.1.3.94.1.6

A list of units under a single SNMP agent. The number of entries is given by the value of uNumber.

The value is 1 for stand-alone system.


53-1001156-01

connUnitEntry 1.3.6.1.3.94.1.6.1

8 connUnitEntry 1.3.6.1.3.94.1.6.1

Index

A connectivity unit entry containing objects for a particular unit. connUnitId


53-1001156-01

885

8 connUnitId 1.3.6.1.3.94.1.6.1.1

connUnitId 1.3.6.1.3.94.1.6.1.1

The unique identification for this connectivity unit among those within this proxy domain. The value must be unique within the proxy domain because it is the index variable for connUnitTable. The value assigned to a given connectivity unit should be persistent across agent and unit resets. It should be the same as connUnitGlobalId if connUnitGlobalId is known and stable.

The Brocade implementation maps the switch WWN to the top 8 octets of this variable and sets the remaining lower 8 octets to 0.

To specify a particular instance of any columnar variable in the connUnitEntry (such as connUnitType), specify the instance identifier as a 16-octet value. connUnitType.10.0.0.60.69.4.11.19.0.0.0.0.0.0.0.0

where the object instance identifier consists of 16 octets, each representing the byte value from high-byte order to low-byte order of this 128-bit integer.


53-1001156-01

connUnitGlobalId 1.3.6.1.3.94.1.6.1.2

8 connUnitGlobalId 1.3.6.1.3.94.1.6.1.2

An optional global-scope identifier for this connectivity unit. It must be a WWN for this connectivity unit or 16 octets of value 0.

The following characteristics are required.

•

WWN formats requiring fewer than 16 octets must be extended to 16 octets with trailing 0 octets.

•

If a WWN is used for connUnitId, the same WWN must be used for connUnitGlobalId.

When a non-zero value is provided, the following characteristics are strongly recommended.

•

It should be persistent across agent and unit resets.

•

It should be globally unique.

•

It should be one of these FC-PH/PH3 formats:

-

IEEE (NAA=1)

-

IEEE Extended (NAA=2)

-

IEEE Registered (NAA=5)

-

IEEE Registered extended (NAA=6)

Use of the IEEE formats allows any IEEE-registered vendor to assure global uniqueness independently. The following are some references on IEEE WWN formats: http://standards.ieee.org/regauth/oui/tutorials/fibreformat.html http://standards.ieee.org/regauth/oui/tutorials/fibrecomp_id.html

If one or more WWNs are associated with the connUnit through other management methods, one of them should be used for connUnitGlobalId.

If a WWN is not assigned specifically to the connUnit, there is some merit to using a WWN assigned to (one of) its permanently attached FC/LAN interfaces. This cannot risk uniqueness, though.

As a counterexample, if your agent runs in a host and the host has an HBA, it is quite possible that agent, host, and HBA are all distinct connUnits, so the host and agent cannot use the WWN of the

HBA.

If your hub has a built-in Ethernet port, it might be reasonable for the hub to use its LAN address

(prefixed with the appropriate NAA) as its connUnitId. But if the Ethernet is a replaceable PCCard, the hub should have an independent ID.

The Brocade implementation maps the switch WWN to the top 8 octets of this variable and sets the remaining lower 8 octets to 0.

Example:

If Brocade’s switch WWN is 10:0:0:60:69:10:02:18, then use the SNMP GET command on connUnitGlobalId.10.0.0.60.69.10.02.18.0.0.0.0.0.0.0.0 returns:

10 00 00 60 69 10 02 18 00 00 00 00 00 00 00 00


53-1001156-01

887

8 connUnitType 1.3.6.1.3.94.1.6.1.3

connUnitType 1.3.6.1.3.94.1.6.1.3

The type of this connectivity unit.

Set to 4 for Fibre Channel switches or to 14 for Brocade Access Gateway.


53-1001156-01

connUnitNumports 1.3.6.1.3.94.1.6.1.4

8 connUnitNumports 1.3.6.1.3.94.1.6.1.4

Number of physical ports (between 0 and the maximum number of system supported ports) in the connectivity unit (internal/embedded, external).

To determine the maximum number of system supported ports, use the SNMP GET command on swFcPortCapacity.

The Brocade switches support 0 to maximum number of system supported ports.

NOTE

The ConnUnitNumports will not count the GE ports present on Iron man blade.

The maximum number of supported ports are as follows.

Brocade 3200, 3250 8 ports

Brocade 4012

Brocade 4016

12 ports

16 ports

Brocade 4018

Brocade 4020

Brocade 4024

Brocade 200E, 3800, 3850

18 ports

20 ports

24 ports

16 ports

Brocade 3900, 4100

Brocade 4900

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000

Brocade 24000

Brocade 48000

Brocade DCX

Brocade DCX-4S

Brocade300

Brocade 5100

Brocade 5300

32 ports

64 ports

32 ports

16 ports

16 ports

128 ports

128 ports

384 ports

384 ports

192 ports

40 ports

80 ports

24 ports


53-1001156-01

889

8 connUnitState 1.3.6.1.3.94.1.6.1.5

connUnitState 1.3.6.1.3.94.1.6.1.5

Values

Overall state of the connectivity unit.


• unknown (1)

• online (2) Set the state to online.

• offline (3) Set the state to offline.

Mapped as follows: switchState(ONLINE) 2 (online) switchState(not ONLINE) 3 (offline, testing, faulty)


53-1001156-01

connUnitStatus 1.3.6.1.3.94.1.6.1.6

Values

Overall status of the connectivity unit.


• unknown (1)

• unused (2)

• ok (3)

• warning (4) - Needs attention.

• failed (5) switchStatus maps directly as follows: connUnitStatus switchStatus

1 (unknown) Unknown

2 (unused) Unmonitored

3 (ok) Healthy/ok

4 (warning) Marginal/Warning

5 (failed) Down/Failed connUnitStatus 1.3.6.1.3.94.1.6.1.6

8


53-1001156-01

891

8 connUnitProduct 1.3.6.1.3.94.1.6.1.7

connUnitProduct 1.3.6.1.3.94.1.6.1.7

The connectivity unit vendor's product model name.

This is the same as for sysDescr (set for as many as 79 bytes).

If the switch is in Access Gateway mode, the default value is Access Gateway.


53-1001156-01

connUnitSn 1.3.6.1.3.94.1.6.1.8

The serial number for this connectivity unit.

Set to the SSN (which by default is the WWN).

connUnitSn 1.3.6.1.3.94.1.6.1.8

8


53-1001156-01

893

8 connUnitUpTime 1.3.6.1.3.94.1.6.1.9

connUnitUpTime 1.3.6.1.3.94.1.6.1.9

The number of centiseconds since the last unit initialization.

Set when connUnitTable is initialized.


53-1001156-01

connUnitUrl 1.3.6.1.3.94.1.6.1.10

8 connUnitUrl 1.3.6.1.3.94.1.6.1.10

URL to launch a management application, if applicable; otherwise an empty string. In a standalone unit, this would be the same as the top-level URL. This has the same definition as systemURL for keywords.

(Same as systemURL.) The expected value for connUnitURL.0 is:

“http://{a.b.c.d}”

where {a.b.c.d} is the IP address of the switch if Web Tools license is available.

“” (null)

where “” is the IP address of the switch if Web Tools license is not available.


53-1001156-01

895

8 connUnitDomainId 1.3.6.1.3.94.1.6.1.11

connUnitDomainId 1.3.6.1.3.94.1.6.1.11

24-bit Fibre Channel address ID of this connectivity unit, right-justified with leading 0s if required. If this value is not applicable, return all bits to 1.

Set to the switch domain ID (as per FC-SW).

For a Brocade Access Gateway device, the value is hard coded as “11 11 11”. A Brocade Access

Gateway does not have a domain ID.


53-1001156-01

connUnitProxyMaster 1.3.6.1.3.94.1.6.1.12

8 connUnitProxyMaster 1.3.6.1.3.94.1.6.1.12

Values

A value of “yes” means this is the proxy master unit for a set of managed units.


• unknown (1)

• no (2)

• yes (3)

This could be the only unit with a management card in it for a set of units. A standalone unit should return “yes” for this object.

Set to 3 (yes).


53-1001156-01

897

8 connUnitPrincipal 1.3.6.1.3.94.1.6.1.13

connUnitPrincipal 1.3.6.1.3.94.1.6.1.13

Values

Indicates whether this connectivity unit is the principal unit within the group of fabric elements. If this value is not applicable, it returns “unknown.”

If the switch is principal, this is set to 3 (yes); otherwise, for a fabric switch it is set to 2 (no). For a

Brocade Access Gateway device, since the switch is behaving as a device management tool and not a Fibre Channel switch, the value is set to 1 (unknown).


• unknown (1)

• no (2)

• yes (3)


53-1001156-01

connUnitNumSensors 1.3.6.1.3.94.1.6.1.14

connUnitNumSensors 1.3.6.1.3.94.1.6.1.14

Number of sensors (between 0 and maximum number of sensors) in the connUnitSensorTable.

Refer to Table 14 on page 552 for specific sensor counts on the various switches.

8


53-1001156-01

899

8 connUnitStatusChangeTime 1.3.6.1.3.94.1.6.1.15

connUnitStatusChangeTime 1.3.6.1.3.94.1.6.1.15

The sysuptime time stamp (in centiseconds) at which the last status change occurred for any members of the set; this is the latest time stamp that connUnitStatus or connUnitPortStatus changed.

Not supported.


53-1001156-01

connUnitConfigurationChangeTime 1.3.6.1.3.94.1.6.1.16

8 connUnitConfigurationChangeTime 1.3.6.1.3.94.1.6.1.16

The sysuptime time stamp (in centiseconds) at which the last configuration change occurred for any members of the set. In other words, this is the latest time stamp of flash memory update. This represents a union of change information for connUnitConfigurationChangeTime

Not supported.


53-1001156-01

901

8 connUnitNumRevs 1.3.6.1.3.94.1.6.1.17

connUnitNumRevs 1.3.6.1.3.94.1.6.1.17

The number of revisions in connUnitRevsTable.

Set to 2.


53-1001156-01

connUnitNumZones 1.3.6.1.3.94.1.6.1.18

8 connUnitNumZones 1.3.6.1.3.94.1.6.1.18

Number of zones defined in connUnitZoneTable.

Not supported.


53-1001156-01

903

8 connUnitModuleId 1.3.6.1.3.94.1.6.1.19

connUnitModuleId 1.3.6.1.3.94.1.6.1.19

This is a unique ID, persistent between boots, that can be used to group a set of connUnits together into a module. The intended use would be to create a connUnit with a connUnitType of “module” to represent a physical or logical group of connectivity units. Then the value of the group would be set to the value of connUnitId for this “container” connUnit.

connUnitModuleId should be 0s if this connUnit is not part of a module.

Set to the WWN of the switch.


53-1001156-01

connUnitName 1.3.6.1.3.94.1.6.1.20

8 connUnitName 1.3.6.1.3.94.1.6.1.20

A display string containing a name for this connectivity unit. This object value should be persistent between boots.

Set to switchName/sysName.


53-1001156-01

905

8 connUnitInfo 1.3.6.1.3.94.1.6.1.21

connUnitInfo 1.3.6.1.3.94.1.6.1.21

A display string containing information about this connectivity unit. This object value should be persistent between boots.

For a fabric switch set to sysDescr and read-only.

For a Brocade Access Gateway device set to “Access Gateway.”


53-1001156-01

connUnitControl 1.3.6.1.3.94.1.6.1.22

8 connUnitControl 1.3.6.1.3.94.1.6.1.22

Values

Controls the addressed connUnit. Each implementation might choose not to allow any or all of these values on a SET.

Cold start and warm start are as defined in MIB-II and are not meant to be a factory reset.

This is similar to swAdmStatus: resetConnunitColdStart = reboot resetConnunitWarmStart = fastboot offlineConnUnit = disable switch onlineConnUnit = enable switch default after reboot = unknown

The declaration 1 (unknown) maps to the default value upon rebooting, and 2 (invalid) is not applicable.

Declarations 3 and 4 perform the same operation—a cold boot of the switch.


• unknown (1)

• invalid (2)

• resetConnUnitColdStart (3): Reboot. Performs a switch reboot.

• resetConnUnitWarmStart (4): Fastboot. The addressed unit performs a Warm Start reset.

• offlineConnUnit (5): Disable switch. The addressed unit puts itself into an implementation-dependant offline state. In general, if a unit is in an offline state, it cannot be used to perform meaningful Fibre Channel work.

• onlineConnUnit (6): Enable switch. The addressed unit puts itself into an implementation-dependant online state. In general, if a unit is in an online state, it is capable of performing meaningful Fibre Channel work.


53-1001156-01

907

8 connUnitContact 1.3.6.1.3.94.1.6.1.23

connUnitContact 1.3.6.1.3.94.1.6.1.23

Contact information for this connectivity unit.

Displays the same value as sysContact. Changing the value in this variable causes the value in sysContact to also be changed.


53-1001156-01

connUnitLocation 1.3.6.1.3.94.1.6.1.24

Location information for this connectivity unit.

Displays the same value as sysLocation.

connUnitLocation 1.3.6.1.3.94.1.6.1.24

8


53-1001156-01

909

8 connUnitEventFilter 1.3.6.1.3.94.1.6.1.25

connUnitEventFilter 1.3.6.1.3.94.1.6.1.25

Return

Defines the event severity logged by this connectivity unit. All events of severity less than or equal to connUnitEventFilter are logged in connUnitEventTable.

Always returns value 9 (debug).


53-1001156-01

connUnitNumEvents 1.3.6.1.3.94.1.6.1.26

8 connUnitNumEvents 1.3.6.1.3.94.1.6.1.26

Values

Number of events currently in connUnitEventTable.

For Fabric OS v3.0 this value ranges from 0 to 64.




For Fabric OS v5.0.1 this value ranges from 0 to 1024.


53-1001156-01

911

8 connUnitMaxEvents 1.3.6.1.3.94.1.6.1.27

connUnitMaxEvents 1.3.6.1.3.94.1.6.1.27

Values

Maximum number of events that can be defined in connUnitEventTable.

For Fabric OS v3.0 this value is 64.




For Fabric OS v5.0.1 this value is 1024.





53-1001156-01

connUnitEventCurrID 1.3.6.1.3.94.1.6.1.28

The last-used event ID (connUnitEventId).

Maximum is 2147483647 (2

31

-1).

connUnitEventCurrID 1.3.6.1.3.94.1.6.1.28

8


53-1001156-01

913

8 connUnitRevsTable 1.3.6.1.3.94.1.7

connUnitRevsTable 1.3.6.1.3.94.1.7

Table of the revisions supported by connectivity units managed by this agent.

Usage Notes This table lists the versions of hardware and software elements in the switch.

One entry for the hardware platform version and another entry for the Fabric OS version. For example, for the Brocade 4100 the hardware platform number is 32.0. The Fabric OS version for this release is 5.1.


53-1001156-01

connUnitRevsEntry 1.3.6.1.3.94.1.7.1

8 connUnitRevsEntry 1.3.6.1.3.94.1.7.1

Index

Table of the revisions supported by connectivity units managed by this agent.

connUnitRevsUnitId connUnitRevsIndex


53-1001156-01

915

8 connUnitRevsUnitId 1.3.6.1.3.94.1.7.1.1

connUnitRevsUnitId 1.3.6.1.3.94.1.7.1.1

The connUnitId value for the connectivity unit that contains this revision table.


53-1001156-01

connUnitRevsIndex 1.3.6.1.3.94.1.7.1.2

8 connUnitRevsIndex 1.3.6.1.3.94.1.7.1.2

A unique value among all connUnitRevsEntrys with the same value of connUnitRevsUnitId, in the range between 1 and connUnitNumRevs.

Index 1 returns the hardware version. Index 2 returns the software version.


53-1001156-01

917

8 connUnitRevsRevId 1.3.6.1.3.94.1.7.1.3

connUnitRevsRevId 1.3.6.1.3.94.1.7.1.3

A vendor-specific string identifying a revision of a component of the connUnit indexed by connUnitRevsUnitId.

Index 1 returns the switchType from switchShow. Index 2 returns the Fabric OS version from telnet command version: for example, v2.6.


53-1001156-01

connUnitRevsDescription 1.3.6.1.3.94.1.7.1.4

8 connUnitRevsDescription 1.3.6.1.3.94.1.7.1.4

Description of a component to which the revision corresponds.

Index 1 returns the hardware version. Index 2 returns the software version.


53-1001156-01

919

8 connUnitSensorTable 1.3.6.1.3.94.1.8

connUnitSensorTable 1.3.6.1.3.94.1.8

Table of the sensors supported by each connectivity unit managed by this agent.

Refer to Table 14 on page 552 for specific sensor counts on the various switches.


53-1001156-01

connUnitSensorEntry 1.3.6.1.3.94.1.8.1

8 connUnitSensorEntry 1.3.6.1.3.94.1.8.1

Index

Each entry contains the information for a specific sensor.

connUnitSensorUnitId connUnitSensorIndex


53-1001156-01

921

8 connUnitSensorUnitId 1.3.6.1.3.94.1.8.1.1

connUnitSensorUnitId 1.3.6.1.3.94.1.8.1.1

The connUnitId value of the connectivity unit that contains this sensor table.

Set to connUnitId.


53-1001156-01

connUnitSensorIndex 1.3.6.1.3.94.1.8.1.2

8 connUnitSensorIndex 1.3.6.1.3.94.1.8.1.2

A unique value among all connUnitSensorEntrys with the same value of connUnitSensorUnitId, in the range between 1 and the return value from connUnitNumSensor.


53-1001156-01

923

8 connUnitSensorName 1.3.6.1.3.94.1.8.1.3

connUnitSensorName 1.3.6.1.3.94.1.8.1.3

A textual identification of the sensor, intended primarily for operator use.

Each contains the name of sensor in textual format: for example, Temp #1, Fan #2, and so on.


53-1001156-01

connUnitSensorStatus 1.3.6.1.3.94.1.8.1.4

8 connUnitSensorStatus 1.3.6.1.3.94.1.8.1.4

Values

The status indicated by the sensor.


• unknown (1)

• other (2)

• ok (3) The sensor indicates okay.

•

Warning (4) The sensor indicates a warning.

• failed (5) The sensor indicates failure.

•

Nominal = 3 (ok).


53-1001156-01

925

8 connUnitSensorInfo 1.3.6.1.3.94.1.8.1.5

connUnitSensorInfo 1.3.6.1.3.94.1.8.1.5

Return

Miscellaneous static information about the sensor, such as its serial number.

Each contains textual information about the sensor.

Returns the serial ID if this is for the power supply; otherwise, returns Null.


53-1001156-01

connUnitSensorMessage 1.3.6.1.3.94.1.8.1.6

8 connUnitSensorMessage 1.3.6.1.3.94.1.8.1.6

This describes the status of the sensor as a message. It may also provide some information about the sensor, for example: sensor 1: type 3 is OK, value is 33

Each contains the sensor status (and reading if applicable) in textual format.


53-1001156-01

927

8 connUnitSensorType 1.3.6.1.3.94.1.8.1.7

connUnitSensorType 1.3.6.1.3.94.1.8.1.7

Values

The type of component being monitored by this sensor.


• unknown (1)

• other (2)

• battery (3)

• fan (4)

• power-supply (5)

• transmitter (6)

• enclosure (7)

• board (8)

• receiver (9)

The following mapping is for each individual sensor, where applicable.

swSensorType

1 (temperature)

2 (fan)

3 (power supply) connUnitSensorType

8 (board)

4 (fan)

5 (power supply)


53-1001156-01

connUnitSensorCharacteristic 1.3.6.1.3.94.1.8.1.8

8 connUnitSensorCharacteristic 1.3.6.1.3.94.1.8.1.8

The characteristics being monitored by this sensor.

The following mapping is for each individual sensor, where applicable: swSensorType

1 (temperature)

2 (fan)

3 (power supply) connUnitSensorCharacteristic

3 (temperature)

7 (airflow)

9 (power)

Values Possible values are:

• unknown (1)

• other (2)

• temperature (3)

• pressure (4)

• emf (5)

• currentValue (6) Current is a keyword.

• airflow (7)

• frequency (8)

• power (9)

• door (10) Not supported in Fabric OS v2.6.1.


53-1001156-01

929

8 connUnitPortTable 1.3.6.1.3.94.1.10

connUnitPortTable 1.3.6.1.3.94.1.10

Generic information on ports for a specific connUnit

NOTE

Information about the GbE ports on a Brocade 7500 or FR4-18i blade is not supported.


53-1001156-01

connUnitPortEntry 1.3.6.1.3.94.1.10.1

8 connUnitPortEntry 1.3.6.1.3.94.1.10.1

Index

Each entry contains the information for a specific port. connUnitPortUnitId connUnitPortIndex


53-1001156-01

931

8 connUnitPortUnitId 1.3.6.1.3.94.1.10.1.1

connUnitPortUnitId 1.3.6.1.3.94.1.10.1.1

The connUnitId value of the connectivity unit that contains this port.

Same value as connUnitId.


53-1001156-01

connUnitPortIndex 1.3.6.1.3.94.1.10.1.2

8 connUnitPortIndex 1.3.6.1.3.94.1.10.1.2

Number of physical ports between 0 and maximum number of system supported ports in the connectivity unit (internal/embedded, external).

To determine the maximum number of system supported ports, use the SNMP GET command on swFcPortCapacity.

The Brocade switches support 0 to maximum number of system supported ports. The maximum number of supported ports are as follows:

Brocade 3200, 3250

Brocade 4012

8 ports

12 ports

Brocade 200E, 3800, 3850

Brocade 3900, 4100

Brocade 4900

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000

Brocade 24000

Brocade 48000

Brocade DCX

16 ports

32 ports

64 ports

32 ports

16 ports

16 ports

128 ports

128 ports

384 ports

384 ports


53-1001156-01

933

8 connUnitPortType 1.3.6.1.3.94.1.10.1.3

connUnitPortType 1.3.6.1.3.94.1.10.1.3

Values

The port type.

For EX_Port, VEX_Port and VE_Port, the port type will be shown as other. For a Brocade Access

Gateway device, the port type can be either F_Port (f-port) or N_Port (n-port) only.


• unknown (1)

• other (2)

• not-present (3)

• hub-port (4)

• n-port (5) End port for fabric.

• l-port (6) End port for loop.

• fl-port (7) Public loop.

• f-port (8) Fabric port.

• e-port (9) Fabric expansion port.

• g-port (10) Generic fabric port.

• domain-ctl (11) Domain controller.

• hub-controller (12)

• scsi (13) Parallel SCSI port.

• escon (14)

• lan (15)

• wan (16)

• ac (17) AC power line. (Not supported in Fabric OS v2.6.1.)

• dc (18) DC power line. (Not supported in Fabric OS v2.6.1)

• ssa (19) Serial storage architecture. (Not supported in Fabric OS v2.6.1.)


53-1001156-01

connUnitPortFCClassCap 1.3.6.1.3.94.1.10.1.4

8 connUnitPortFCClassCap 1.3.6.1.3.94.1.10.1.4

Bit mask that specifies the classes of service capability of this port. If this is not applicable, return all bits set to 0.

The bits have the following definition:

• unknown 0

• class-f 1

• class-one 2

• class-two 4

• class-three 8

• class-four 16

• class-five 32

• class-six 64

For an F_Port or FL_Port, this value is 0x000C. For a G_Port or E_Port, this value is 0x000D.

For a Brocade Access Gateway, both the F_Port and N_Port this value is 0x0008. An Access

Gateway supports class-three services only, therefore the value is 8 for both port types.

connUnitPortFCClassCap attribute is dependent on the state of the port i.e, whether the port is online or offline. If the port is offline , the class service of U port will be shown as value of onnUnitPortFCClassCap. If it is online , then this mib attribute value will be equal to class service corresponding to the port type (F, E , L port ..)


53-1001156-01

935

8 connUnitPortFCClassOp 1.3.6.1.3.94.1.10.1.5

connUnitPortFCClassOp 1.3.6.1.3.94.1.10.1.5

Bit mask that specifies the classes of service that are currently operational. If this is not applicable, return all bits set to 0. This object has the same definition as connUnitPortFCClassCap.

For an F_Port or FL_Port, this value is 0x000C. For a G_Port or E_Port, this value is 0x000D.

For a Brocade Access Gateway both the F_Port and N_Port this value is 0x0008. A Brocade Access

Gateway supports class-three services only, therefore the value is 8 for both port types.

connUnitPortFCClassOp is independent of the state of the port (online or offline). Its value is only dependent on the port type.


53-1001156-01

connUnitPortState 1.3.6.1.3.94.1.10.1.6

8 connUnitPortState 1.3.6.1.3.94.1.10.1.6

Values

The state of the port hardware.


• unavailable (1) Do not use.

• online (2) Available for meaningful work.

• offline (3) Not available for meaningful work.

• bypassed (4) No longer used.

• diagnostics (5) Map to your testing. (Not supported in Fabric OS v2.6.1.)

For an E, F, or FL_Port, the value is online. For a U_Port, the value is offline (disabled, testing, faulted).


53-1001156-01

937

8 connUnitPortStatus 1.3.6.1.3.94.1.10.1.7

connUnitPortStatus 1.3.6.1.3.94.1.10.1.7

Values

An overall protocol status for the port. For a U_Port, the status should be ols (9).


• unknown (1)

• unused (2) Device cannot report this status.

• ready (3) FCAL Loop or FCPH Link reset protocol initialization has completed.

• warning (4) Do not use.

• failure (5) Port is faulty.

• notparticipating (6) Loop not participating and does not have a loop address. Do not use.

• initializing (7) Protocol is proceeding. Do not use.

• bypass (8) Do not use.

• ols (9) FCP offline status. (Not supported in Fabric OS v2.6.1.)

NOTE

In Fabric OS v2.6.x, for an E_Port, F_Port, or FL_Port, the value is 3 (ok). For a U_Port, the value is 2

(unused) if not faulty with GBIC, 1(unknown) if not faulty but no GBIC, or 5 (failure) if faulty.

In Fabric OS v3.x and above, for an E_Port, F_Port, FL_Port or other Port and online port state, the value is 3 (ok). For G_Port or other Port and offline port state, the value is 9 (ols). For unknown portype and offline port state, the value is 1 (unknown).


53-1001156-01

connUnitPortTransmitterType 1.3.6.1.3.94.1.10.1.8

8 connUnitPortTransmitterType 1.3.6.1.3.94.1.10.1.8

Values

The technology of the port transceiver.


• unknown (1)

• other (2)

• unused (3)

• shortwave (4)

• longwave (5)

• copper (6)

• scsi (7)

• longwaveNoOFC (8)

• shortwaveNoOFC (9)

• longwaveLED (10)

• ssa (11) (Not supported in Fabric OS v2.6.1.)

For an external FC_Port, this value should be 9 (shortwaveNoOFC), 8 (longwaveNoOFC), or 6

(copper).


53-1001156-01

939

8 connUnitPortModuleType 1.3.6.1.3.94.1.10.1.9

connUnitPortModuleType 1.3.6.1.3.94.1.10.1.9

Values

The module type of the port connector.


• unknown (1)

• other (2)

• gbic (3)

• embedded (4) Fixed (oneXnine)

• glm (5)

• gbicSerialId (6)

• gbicNoSerialId (7)

• gbicNotInstalled (8)

• smallFormFactor (9)

For an external FC_Port with GBIC, this value is set to 6 (gbicSerialId) or 7 (gbicNoSerialId). For an external FC_Port without GBIC, this value is set to 8 (gbicNotInstalled).


53-1001156-01

connUnitPortWwn 1.3.6.1.3.94.1.10.1.10

8 connUnitPortWwn 1.3.6.1.3.94.1.10.1.10

The World Wide Name of the port, if applicable; otherwise, an empty string.

This is in IEEE Extended format, and the extension contains the internal port number of each port.

NOTE

The internal port number is 1 less than the port index. For example, if the switch has WWN

10:00:00:60:69:10:02:18, then port numbers 0 and 6 have WWN 20:00:00:60:69:10:02:18 and

20:06:00:60:69:10:02:18, respectively. However, the embedded port has WWN

10:00:00:60:69:10:02:18, the same as the switch.


53-1001156-01

941

8 connUnitPortFCId 1.3.6.1.3.94.1.10.1.11

connUnitPortFCId 1.3.6.1.3.94.1.10.1.11

This is the assigned Fibre Channel ID of this port. This value is expected to be a Big Endian value of

24 bits. If this is a loop, then it is the AL_PA that is connected. If this is an E_Port, then it contains only the domain ID, left justified, 0 filled. If this port does not have a Fibre Channel address, return all bits set to 1.

For an F_Port, this is the Fibre Channel ID to which the connected N_port is assigned. For an

FL_Port, this is the Fibre Channel ID of the FL_Port (alpa = 0). For a U or E_Port, this is similar to

F_Port.

The FC ID is formatted “DD AA PP” (e.g., “02 00 02”). The Brocade Access Gateway port FC ID differs from a Fibre Channel switch. A Fibre Channel switch port FC ID has the same DD with a different AA value for each link. The Brocade Access Gateway “PP” is the port number for F_Ports and is always zero for N_Ports. Therefore the N_Port FC ID always appears as “DD AA 00” (e.g., “02

00 00”). On a Brocade Access Gateway the FC ID of different ports can have the same “AA” value but different “DD” values and vice versa.


53-1001156-01

connUnitPortSn 1.3.6.1.3.94.1.10.1.12

8 connUnitPortSn 1.3.6.1.3.94.1.10.1.12

The serial number of the unit (for example, for a GBIC). If this is not applicable, return an empty string.

If the GBIC has a serial ID, the return value is the GBIC part number; otherwise, the return value is

Null.


53-1001156-01

943

8 connUnitPortRevision 1.3.6.1.3.94.1.10.1.13

connUnitPortRevision 1.3.6.1.3.94.1.10.1.13

Return

The port revision (for example, GBIC).

If the GBIC has a serial ID, this returns the GBIC revision number; otherwise, it returns a Null value.


53-1001156-01

connUnitPortVendor 1.3.6.1.3.94.1.10.1.14

connUnitPortVendor 1.3.6.1.3.94.1.10.1.14

Return

The port vendor (for example, for a GBIC).

If the GBIC has a serial ID, this returns the GBIC vendor name; otherwise, it returns a Null value.

8


53-1001156-01

945

8 connUnitPortSpeed 1.3.6.1.3.94.1.10.1.15

connUnitPortSpeed 1.3.6.1.3.94.1.10.1.15

The speed of the port, in kilobytes per second.

For example, the valid values for Brocade 12000, 24000, and 48000 directors: 125,000 KBps,

250,000 KBps, or 500,000 KBps depending on the configuration.


53-1001156-01

connUnitPortControl 1.3.6.1.3.94.1.10.1.16

8 connUnitPortControl 1.3.6.1.3.94.1.10.1.16

Controls the addressed connUnit’s port.

Valid commands are:

• resetConnUnitPort

If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific reset operation.

Examples of these operations are:

•

The Link Reset protocol.

•

The Loop Initialization protocol.

•

Resynchronization occurring between the transceiver in the addressed port to the transceiver to which the port is connected.

• bypassConnUnitPort

If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific “bypass” operation.


•

Transitioning from online to offline.

•

A request (NON-PARTICIPATING) command to the loop port state machine.

•

Removal of the port from an arbitrated loop by a hub.

• unbypassConnUnitPort

If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific “unbypass” operation. Examples of these operations are

•

The Link Failure protocol.

•

A request (PARTICIPATING) command to the loop port state machine.

•

Addition of the port to an arbitrated loop by a hub.

• offlineConnUnitPort

If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific offline operation.


•

Disabling a port's transceiver.

•

The Link Failure protocol.

•

Request (NON-PARTICIPATING) command to the loop port state machine removal of the port from an arbitrated loop by a hub.

• onlineConnUnitPort

If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific online operation.


•

Enabling a port's transceiver.

•

The Link Failure protocol, request (PARTICIPATING) command to the loop port state machine.


53-1001156-01

947

8 connUnitPortControl 1.3.6.1.3.94.1.10.1.16

•

Addition of the port from an arbitrated loop by a hub.

Each implementation might choose not to allow any or all of these values on a SET.

If the management station uses in-band communication (FC-IP) with the switch, either of the two following actions might result in a loss of in-band communication with the switch.

•

Disabling the FC port that is connected to the management station

•

Disabling the embedded port

•

Return values are:

resetConnUnitPort portDisable (F or E_Port, loop for U_Port)

bypassConnUnitPort portDisable (FL_Port)

unbypassConnUnitPort portEnable (FL_Port)

offlineConnUnitPort portDisable (E, F, FL_Port)

onlineConnUnitPort portEnable (U)

resetConnUnitPortCounters clear the port statistics counter. When rebooted, this defaults to 1 (unknown).


53-1001156-01

connUnitPortName 1.3.6.1.3.94.1.10.1.17

A string describing the addressed port.

This object is read-only for Brocade switches.

connUnitPortName 1.3.6.1.3.94.1.10.1.17

8


53-1001156-01

949

8 connUnitPortPhysicalNumber 1.3.6.1.3.94.1.10.1.18

connUnitPortPhysicalNumber 1.3.6.1.3.94.1.10.1.18

This is the internal port number by which this port is known. In many implementations, this should be the same as connUnitPortIndex. Some implementations might have an internal port representation not compatible with the rules for table indices. In these cases, provide the internal representation of this port in this object. This value might also be used in the connUnitLinkPortNumberX or connUnitLinkPortNumberY objects of the connUnitLinkTable.

The internal port numbers for Brocade switch. The Brocade switches support 0 through maximum

number of ports.

The maximum number of supported ports are as follows.

Brocade 3200, 3250 8 ports

Brocade 4012

Brocade 200E, 3800, 3850

12 ports

16 ports

Brocade 3900, 4100

Brocade 4900

Brocade 5000

Brocade 7500

Brocade 7600

Brocade 12000

Brocade 24000

Brocade 48000

Brocade DCX

Brocade DCX-4S

Brocade 300

Brocade 5100

Brocade 5300

32 ports

64 ports

32 ports

16 ports

16 ports

128 ports

128 ports

384 ports

384 ports

192 ports

40 ports

80 ports

24 ports


53-1001156-01

connUnitPortStatObject 1.3.6.1.3.94.1.10.1.19

8 connUnitPortStatObject 1.3.6.1.3.94.1.10.1.19

This OID is depricated.

This contains the OID of the first object of the table that contains the statistics for this particular port. If this has a value of 0, then there are no statistics available for this port. The port type information helps identify the statistics objects found in the table. From this point, use the getnext command to get the next statistics object. When the first part of the OID changes, the end of table is reached.

Mapped to connUnitPortStatFabricUnitId.


53-1001156-01

951

8 connUnitPortProtocolCap 1.3.6.1.3.94.1.10.1.20

connUnitPortProtocolCap 1.3.6.1.3.94.1.10.1.20


This is the bit mask that specifies the driver-level protocol capability of this port.

If this is not applicable, return all bits set to 0.

Return value = 07F

The bits have the following definition.

•

0 = unknown

•

1 = Loop

•

2 = Fabric

•

4 = SCSI

•

8 = TCP/IP

•

16 = VI

•

32 = FICON


53-1001156-01

connUnitPortProtocolOp 1.3.6.1.3.94.1.10.1.21

8 connUnitPortProtocolOp 1.3.6.1.3.94.1.10.1.21

Not supported in Fabric OS v2.6.1.Supported in v5.x, v6.0.

This is the bit mask that specifies the driver level protocol(s) that are currently operational.

Return value = 07F

If this is not applicable, return all bits set to zero. The bits have the following definition:

•

0 = unknown

•

1 = Loop

•

2 = Fabric

•

4 = SCSI

•

8 = TCP/IP

•

16 = VI

•

32 = FICON


53-1001156-01

953

8 connUnitPortNodeWwn 1.3.6.1.3.94.1.10.1.22

connUnitPortNodeWwn 1.3.6.1.3.94.1.10.1.22

Not supported in Fabric OS v2.6.1. Supported in v5.x, v6.0.

The node World Wide Name of the port, if applicable; otherwise, an empty string.

All related ports in within a group should have the same node WWN value. The container is defined as the largest physical entity.

All ports on HBAs on a host will have the same node WWN. All ports on the same storage subsystem will have the same node WWN.

This is in IEEE Extended format and the extension contains the internal port number of each port.

The internal port number is 1 less than the port index. For example, if the switch has WWN

10:00:00:60:69:10:02:18, then port number 0 and 6 have WWN 20:00:00:60:69:10:02:18 and

20:06:00:60:69:10:02:18, respectively. However, the embedded port has WWN

10:00:00:60:69:10:02:18, the same as the switch.

The N_Ports on a Brocade Access Gateway are the WWN of the switch (i.e., it is the same as the connUnitId). The F_Ports are the WWN of the HBA host. If the F_Port is offline, the value of the

WWN is zero (00:00:00:00:00:00:00:00).


53-1001156-01

connUnitPortHWState 1.3.6.1.3.94.1.10.1.23

8 connUnitPortHWState 1.3.6.1.3.94.1.10.1.23

Values


The state of the port as detected by the hardware.


• unknown (1)

• failed (2) Port failed diagnostics (port_flt_state).

• bypassed (3) FCAL bypass, loop only (not used).

• active (4) Connected to a device (light and sync are present).

• loopback (5) Port in ext loopback (loopback state).

• txfault (6) Transmitter fault (bad GBIC).

• noMedia (7) Media not installed (GBIC removed).

• linkDown (8) Waiting for activity—rx sync (light with no sync).


53-1001156-01

955

8 connUnitEventTable 1.3.6.1.3.94.1.11

connUnitEventTable 1.3.6.1.3.94.1.11

The table of connectivity unit events. Errors, warnings, and information should be reported in this table.

•

(v3.0 only) This table contains the 64 most-recent event log entries.

•


•


•

(v4.4 and above) This table contains the 1024 most-recent event log entries.

•


Only external RASlog messages are supported. Fabric OS v4.4.0 and above do not have Panic or

Debug level messages. All external messages are documented in the Fabric OS Message

Reference.


53-1001156-01

connUnitEventEntry 1.3.6.1.3.94.1.11.1

8 connUnitEventEntry 1.3.6.1.3.94.1.11.1

Index

Each entry contains information on a specific event for the given connectivity unit. connUnitEventUnitId connUnitEventIndex


53-1001156-01

957

8 connUnitEventUnitId 1.3.6.1.3.94.1.11.1.1

connUnitEventUnitId 1.3.6.1.3.94.1.11.1.1

The connUnitId of the connectivity unit that contains this event table.

Same as connUnitId.


53-1001156-01

connUnitEventIndex 1.3.6.1.3.94.1.11.1.2

8 connUnitEventIndex 1.3.6.1.3.94.1.11.1.2

Each connectivity unit has its own event buffer. As it wraps, it might write over previous events. This object is an index into the buffer. It is recommended that this table is read using “getNext”s to retrieve the initial table. The management application should read the event table at periodic intervals and then determine if any new entries were added by comparing the last known index value with the current highest index value. The management application should then update its copy of the event table. If the read interval is too long, it is possible that there might be events that might not be contained in the agent's internal event buffer.

An agent might read events 50-75.

At the next read interval, connUnitEventCurrID is 189. If the management application tries to read event index 76 and the agent's internal buffer is 100 entries maximum, event index 76 is no longer available.

The index value is an incrementing integer starting from 1 every time there is a table reset. On table reset, all contents are emptied and all indices are set to 0. When an event is added to the table, the event is assigned the next-higher integer value than the last item entered into the table.

If the index value reaches its maximum value, the next item entered causes the index value to roll over and start at 1 again.

Mapped to swEventIndex.


53-1001156-01

959

8 connUnitEventId 1.3.6.1.3.94.1.11.1.3

connUnitEventId 1.3.6.1.3.94.1.11.1.3

The internal event ID. Incriminated for each event, ranging between 0 and connUnitMaxEvents. Not used as table index to simplify the agent implementation. When this reaches the end of the range specified by connUnitMaxEvents, the ID rolls over to start at 0. This value is set back to 0 at reset.

The relationship of this value to the index is that internal event ID might represent a smaller number than a 32-bit integer (for example, maximum 100 entries) and would only have a value range up to connUnitMaxEvents.

Same function as connUnitEventIndex.


53-1001156-01

connUnitREventTime 1.3.6.1.3.94.1.11.1.4

8 connUnitREventTime 1.3.6.1.3.94.1.11.1.4

This is the real time when the event occurred. It has the following format.

DDMMYYYY HHMMSS

Where:

DD = day number

MM = month number

YYYY = year

HH = hours

MM = minutes

SS = seconds

If not applicable, returns a null string.


53-1001156-01

961

8 connUnitSEventTime 1.3.6.1.3.94.1.11.1.5

connUnitSEventTime 1.3.6.1.3.94.1.11.1.5

This is the sysuptime time stamp when the event occurred.


53-1001156-01

connUnitEventSeverity 1.3.6.1.3.94.1.11.1.6

8 connUnitEventSeverity 1.3.6.1.3.94.1.11.1.6

The event severity level. The mapping between errorlog severity level and this variable is:

Error log none (0)

Critical (1)

Error (2)

Warning (3)

Informational (4)

Debug (5)

FA-MIB unknown (1) critical (4) error (5) warning (6) info (8) debug (9)

Refer to FcEventSeverity in Table 20 on page 879 for more information about severity.


53-1001156-01

963

8 connUnitEventType 1.3.6.1.3.94.1.11.1.7

connUnitEventType 1.3.6.1.3.94.1.11.1.7

Values

The type of this event.


• unknown (1)

• other (2)

• status (3)

• configuration (4)

• topology (5)

Always set to 2 (other).


53-1001156-01

connUnitEventObject 1.3.6.1.3.94.1.11.1.8

8 connUnitEventObject 1.3.6.1.3.94.1.11.1.8

Values

This is used with the connUnitEventType to identify to which object the event refers. It can be the

OID of a connectivity unit or of another object, like connUnitPortStatus[...].

Always set to null.


53-1001156-01

965

8 connUnitEventDescr 1.3.6.1.3.94.1.11.1.9

connUnitEventDescr 1.3.6.1.3.94.1.11.1.9

The description of the event.

Same as the string displayed in the system error log. The system error log can be viewed using the errShow or errDump commands.

For Fabric OS v6.2.0, the format of error messages has changed. This field now uses the message title and number (for example, WEBD-1006) and the message text. Previously, this field used the task ID and all the message number and message text. For more information on error messages, refer to Fabric OS Message Reference.


53-1001156-01

connUnitLinkTable 1.3.6.1.3.94.1.12

8 connUnitLinkTable 1.3.6.1.3.94.1.12

A list of links known to this agent from this connectivity unit to other connectivity units- X is switch data and Y is other end.

The link table is intended to organize and communicate any information the agent has that might assist a management application to discover the connectivity units in the framework and the topology of their interconnect- the goal is to assist the management application by mapping the elements of the framework in addition to listing them.

With this goal, the agent should include as much as it possesses about any links from its own connectivity units to others, including links among its own units.

An agent should include partial information about links if it is not able to fully define them in accord with the following structure; however, the information must include either a nonzero connUnitNodeId—or a nonzero connUnitPortWwn—for each end of the link.

If the agent is able to discover links that do not directly attach to members of its agency and its discovery algorithm gives some assurance that the links are recently valid, it might include these links.

Link information entered by administrative action might be included even if not validated directly if the link has at least one endpoint in this agency, but it should not be included otherwise.

A connectivity unit should fill the table in as best it can. One of the methods to fill this in would be to use the RNID ELS command (ANSI document 99-422v0). This command queries a port for the information needed for the link table.

This table is accessed either directly, if the management software has an index value, or using getNext. The values of the indexes are not required to be contiguous. Each entry created in this table is assigned an index. This relationship is kept persistent until the entry is removed from the table or the system is reset. The total number of entries is defined by the size of the table.

For an entry to be considered valid, both the X (local) and the Y (remote) values need to have one valid value.

A Brocade Access Gateway has no ISLs (InterSwitch Links); therefore all F_Port and N_Port connections display in ag --show for online F_Ports.

Dedicated ISL DISL An ISL physically connected between two virtual switches belonging to same VF ID. A DISL is dedicated to carry frames only related to VF ID of connected virtual switches.

Extended ISL XISL A XISL belongs to the base fabric and by default carries frames of the base fabric and for other fabrics using the encapsulation and IFR header.

Logical ISL LISL A virtual link between 2 virtual switches that is used for control frames. LISL might not map directly to a single physical ISL depending on topology.


53-1001156-01

967

8 connUnitLinkEntry 1.3.6.1.3.94.1.12.1

connUnitLinkEntry 1.3.6.1.3.94.1.12.1

Index

An entry describing a particular link to another.

connUnitLinkUnitId connUnitLinkIndex


53-1001156-01

connUnitLinkUnitId 1.3.6.1.3.94.1.12.1.1

8 connUnitLinkUnitId 1.3.6.1.3.94.1.12.1.1

Values

The connUnitId of the connectivity unit that contains this link table.

Set to WWN of the local switch.


53-1001156-01

969

8 connUnitLinkIndex 1.3.6.1.3.94.1.12.1.2

connUnitLinkIndex 1.3.6.1.3.94.1.12.1.2

This value is used to create a unique value for each entry in the link table with the same connUnitLinkUnitId. The value can only be reused if it is not currently in use and the value is the next candidate to be used. This value is allowed to wrap at the highest value represented by the number of bits. This value is reset to 0 when the system is reset and the first value to be used is 1.

Indexes 1 through maximum number of ports is reserved for ISL.

Indexes maximum number of ports + 1 and above are reserved for end devices and are calculated based on portID of the end device(s).


53-1001156-01

connUnitLinkNodeIdX 1.3.6.1.3.94.1.12.1.3

8 connUnitLinkNodeIdX 1.3.6.1.3.94.1.12.1.3

The node WWN of the unit at one end of the link. If the node WWN is unknown and the node is a connUnit in the responding agent, then the value of this object must be equal to its connUnitID.

WWN of the local switch.


53-1001156-01

971

8 connUnitLinkPortNumberX 1.3.6.1.3.94.1.12.1.4

connUnitLinkPortNumberX 1.3.6.1.3.94.1.12.1.4

The port number on the unit specified by connUnitLinkNodeIdX, if known; otherwise, -1. If the value is nonnegative, then it is equal to connUnitPortPhysicalNumber.

ISL- Physical port number of the E_Port.

Device- Physical port # to which the device is connected.


53-1001156-01

connUnitLinkPortWwnX 1.3.6.1.3.94.1.12.1.5

connUnitLinkPortWwnX 1.3.6.1.3.94.1.12.1.5

The port WWN of the unit specified by connUnitLinkNodeIdX, if known; otherwise, 16 octets of binary 0.

This is the WWN of the port to which the device is connected.

8


53-1001156-01

973

8 connUnitLinkNodeIdY 1.3.6.1.3.94.1.12.1.6

connUnitLinkNodeIdY 1.3.6.1.3.94.1.12.1.6

The node WWN of the unit at the other end of the link. If the node WWN is unknown and the node is a connUnit in the responding SNMP agency, then the value of this object must be equal to its connUnitID.

ISL- WWN of the remote switch.

Device- Node name of the device.


53-1001156-01

connUnitLinkPortNumberY 1.3.6.1.3.94.1.12.1.7

8 connUnitLinkPortNumberY 1.3.6.1.3.94.1.12.1.7

The port number on the unit specified by connUnitLinkNodeIdY, if known; otherwise, -1. If the value is nonnegative then it is equal to connUnitPortPhysicalNumber.

ISL- Physical port number of the remote port.

Device: -1.


53-1001156-01

975

8 connUnitLinkPortWwnY 1.3.6.1.3.94.1.12.1.8

connUnitLinkPortWwnY 1.3.6.1.3.94.1.12.1.8

The port WWN on the unit specified by connUnitLinkNodeIdY, if known; otherwise, 16 octets of binary 0.

ISL- WWN of the remote port.

Device- Port name.


53-1001156-01

connUnitLinkAgentAddressY 1.3.6.1.3.94.1.12.1.9

8 connUnitLinkAgentAddressY 1.3.6.1.3.94.1.12.1.9

The address of an FCMGMT MIB agent for the node identified by connUnitLinkNodeIdY, if known; otherwise, 16 octets of binary 0.

ISL- IP address (IPv4).

Device- 0 (Null).


53-1001156-01

977

8 connUnitLinkAgentAddressTypeY 1.3.6.1.3.94.1.12.1.10

connUnitLinkAgentAddressTypeY 1.3.6.1.3.94.1.12.1.10

If connUnitLinkAgentAddressY is nonzero, it is a protocol address. ConnUnitLinkAgentAddressTypeY is the “address family number” assigned by IANA to identify the address format (for example, 1 is

Ipv4, 2 is Ipv6).

ISL- Type 1.

Device- 0 (Null).


53-1001156-01

connUnitLinkAgentPortY 1.3.6.1.3.94.1.12.1.11

connUnitLinkAgentPortY 1.3.6.1.3.94.1.12.1.11

The IP port number for the agent. This is provided in case the agent is at a non-standard SNMP port.

ISL- IP port.

Device- 0 (Null).

8


53-1001156-01

979

8 connUnitLinkUnitTypeY 1.3.6.1.3.94.1.12.1.12

connUnitLinkUnitTypeY 1.3.6.1.3.94.1.12.1.12

Type of the FC connectivity unit, as defined in connUnitType.

•

ISL- Switch device.

•

End devices- End device types based on an FCP Inquiry.

Brocade does not support Hubs.

TABLE 21

connUnitLinkUnitTypeY End Devices

Storage System Storage Sub-system

Direct Access

Sequential Access

Write-Once

CD-ROM

Optical

Medium Changer

Array

SES

Unknown

Unknown

Other

Anything else (printer device, processor device, scanner, and so on)


53-1001156-01

connUnitLinkConnIdY 1.3.6.1.3.94.1.12.1.13

8 connUnitLinkConnIdY 1.3.6.1.3.94.1.12.1.13

This is the Fibre Channel ID of this port. If the connectivity unit is a switch, this is expected to be a

Big Endian value of 24 bits. If this is loop, then it is the AL_PA that is connected. If this is an E_port, then it contains only the domain ID. If not any of those, unknown or cascaded loop, return all bits set to 1.

ISL- Port ID of the remote port.

Device- Port ID of the remote port.


53-1001156-01

981

8 connUnitLinkCurrIndex 1.3.6.1.3.94.1.12.1.14

connUnitLinkCurrIndex 1.3.6.1.3.94.1.12.1.14


The last-used link index.

Statistics Group


Port types are aggregated into a port type class, such as all the fabric port types.

Each individual port has only one statistics table. For all objects in the statistics table, if the object is not supported by the conn unit, then the high order bit is set to 1, with all other bits set to 0 (for example, the last eight bytes of the returned value might be ...:80 00 00 00 00 00 00 00).

The high order bit is reserved to indicate whether the object is supported. All objects start at a value of 0 at hardware initialization and continue incrementing until end of 63 bits and then wrap to 0.

This is the case for all Class 1 Frames; Brocade does not support them.


53-1001156-01

connUnitPortStatTable 1.3.6.1.3.94.4.5

A list of statistics for the fabric port types.

connUnitPortStatTable 1.3.6.1.3.94.4.5

8


53-1001156-01

983

8 connUnitPortStatEntry 1.3.6.1.3.94.4.5.1

connUnitPortStatEntry 1.3.6.1.3.94.4.5.1

Index

An entry describing port statistics.

connUnitPortStatUnitId connUnitPortStatIndex


53-1001156-01

connUnitPortStatUnitId 1.3.6.1.3.94.4.5.1.1

8 connUnitPortStatUnitId 1.3.6.1.3.94.4.5.1.1

The connUnitId of the connectivity unit that contains this port statistics table.


53-1001156-01

985

8 connUnitPortStatIndex 1.3.6.1.3.94.4.5.1.2

connUnitPortStatIndex 1.3.6.1.3.94.4.5.1.2

A unique value among all entries in this table, between 0 and connUnitNumPort[connUnitPortUnitId].


53-1001156-01

connUnitPortStatCountError 1.3.6.1.3.94.4.5.1.3

8 connUnitPortStatCountError 1.3.6.1.3.94.4.5.1.3

A count of the errors that have occurred on this port.


53-1001156-01

987

8 connUnitPortStatCountTxObjects 1.3.6.1.3.94.4.5.1.4

connUnitPortStatCountTxObjects 1.3.6.1.3.94.4.5.1.4

The number of frames, packets, IOs, and so forth, that have been transmitted by this port.

A Fibre Channel frame starts with SOF and ends with EOF. FC loop devices should not count frames passed through. This value represents the sum total for all other Tx objects.


53-1001156-01

connUnitPortStatCountRxObjects 1.3.6.1.3.94.4.5.1.5

8 connUnitPortStatCountRxObjects 1.3.6.1.3.94.4.5.1.5

The number of frames, packets, IOs, and so forth, that have been received by this port.

A Fibre Channel frame starts with SOF and ends with EOF. FC loop devices should not count frames passed through. This value represents the sum total for all other Rx objects.


53-1001156-01

989

8 connUnitPortStatCountTxElements 1.3.6.1.3.94.4.5.1.6

connUnitPortStatCountTxElements 1.3.6.1.3.94.4.5.1.6

The number of octets or bytes that have been transmitted by this port. There is an one-second periodic polling of the port. This value is saved and compared with the next polled value to compute net throughput.

For Fibre Channel, ordered sets are not included in the count.


53-1001156-01

connUnitPortStatCountRxElements 1.3.6.1.3.94.4.5.1.7

8 connUnitPortStatCountRxElements 1.3.6.1.3.94.4.5.1.7

The number of octets or bytes that have been received by this port. There is an one-second periodic polling of the port. This value is saved and compared with the next polled value to compute net throughput.

For Fibre Channel, ordered sets are not included in the count.


53-1001156-01

991

8 connUnitPortStatCountBBCreditZero 1.3.6.1.3.94.4.5.1.8

connUnitPortStatCountBBCreditZero 1.3.6.1.3.94.4.5.1.8

The number of transitions in/out of BB credit zero state. The other side is not providing any credit.

This is a Fibre Channel statistic only.


53-1001156-01

connUnitPortStatCountInputBuffersFull 1.3.6.1.3.94.4.5.1.9

8 connUnitPortStatCountInputBuffersFull 1.3.6.1.3.94.4.5.1.9

Supported.

The number of occurrences when all input buffers of a port were full and outbound buffer-to-buffer credit transitioned to 0. There is no credit to provide to other side.

Return Value- 80 0 0 0 0 0 0 0 (Not Supported)

This is a Fibre Channel statistic only.


53-1001156-01

993

8 connUnitPortStatCountFBSYFrames 1.3.6.1.3.94.4.5.1.10

connUnitPortStatCountFBSYFrames 1.3.6.1.3.94.4.5.1.10

The number of times that FBSY was returned to this port as a result of a frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. Port can only occur on SOFc1 frames (the frames that establish a connection).

This is a Fibre Channel only statistic. This is the sum of all classes. If you cannot keep the by-class counters, then keep the sum counters.


53-1001156-01

connUnitPortStatCountPBSYFrames 1.3.6.1.3.94.4.5.1.11

8 connUnitPortStatCountPBSYFrames 1.3.6.1.3.94.4.5.1.11

Supported.

The number of times that PBSY was returned to this port as a result of a frame that could not be delivered to the other end of the link. This occurs if the destination port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection).

Return Value- 80 0 0 0 0 0 0 0 (not supported)

This is a Fibre Channel only statistic. This is the sum of all classes. If you cannot keep the by class counters, then keep the sum counters.


53-1001156-01

995

8 connUnitPortStatCountFRJTFrames 1.3.6.1.3.94.4.5.1.12

connUnitPortStatCountFRJTFrames 1.3.6.1.3.94.4.5.1.12

The number of times that FRJT was returned to this port as a result of a frame that was rejected by the fabric.

This is the total for all classes and is a Fibre Channel only statistic.


53-1001156-01

connUnitPortStatCountPRJTFrames 1.3.6.1.3.94.4.5.1.13

8 connUnitPortStatCountPRJTFrames 1.3.6.1.3.94.4.5.1.13

Supported.

The number of times that FRJT was returned to this port as a result of a frame that was rejected at the destination N_Port.

Return Value- 80 0 0 0 0 0 0 0

This is the total for all classes and is a Fibre Channel only statistic.


53-1001156-01

997

8 connUnitPortStatCountClass1RxFrames 1.3.6.1.3.94.4.5.1.14

connUnitPortStatCountClass1RxFrames 1.3.6.1.3.94.4.5.1.14

The number of Class 1 Frames received at this port.

This is a Fibre Channel only statistic. Brocade does not support Class 1 Frames.

Return value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountClass1TxFrames 1.3.6.1.3.94.4.5.1.15

8 connUnitPortStatCountClass1TxFrames 1.3.6.1.3.94.4.5.1.15

The number of Class 1 Frames transmitted out this port. This is a Fibre Channel only statistic.

Brocade does not support Class 1 Frames.

Return value- 80 0 0 0 0 0 0 0


53-1001156-01

999

8 connUnitPortStatCountClass1FBSYFrames 1.3.6.1.3.94.4.5.1.16

connUnitPortStatCountClass1FBSYFrames 1.3.6.1.3.94.4.5.1.16

The number of times that FBSY was returned to this port as a result of a Class 1 Frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection).


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountClass1PBSYFrames 1.3.6.1.3.94.4.5.1.17

8 connUnitPortStatCountClass1PBSYFrames 1.3.6.1.3.94.4.5.1.17

The number of times that PBSY was returned to this port as a result of a Class 1 Frame that could not be delivered to the other end of the link. This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection).


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1001

8 connUnitPortStatCountClass1FRJTFrames 1.3.6.1.3.94.4.5.1.18

connUnitPortStatCountClass1FRJTFrames 1.3.6.1.3.94.4.5.1.18

The number of times that FRJT was returned to this port as a result of a Class 1 Frame that was rejected by the fabric.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountClass1PRJTFrames 1.3.6.1.3.94.4.5.1.19

8 connUnitPortStatCountClass1PRJTFrames 1.3.6.1.3.94.4.5.1.19

The number of times that FRJT was returned to this port as a result of a Class 1 Frame that was rejected at the destination N_Port.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1003




This is a Fibre Channel only statistic. Not supported.

Return value- 80 0 0 0 0 0 0 0


53-1001156-01



The number of Class 2 Frames transmitted out this port.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1005

8 connUnitPortStatCountClass2FBSYFrames 1.3.6.1.3.94.4.5.1.22

connUnitPortStatCountClass2FBSYFrames 1.3.6.1.3.94.4.5.1.22

The number of times that FBSY was returned to this port because Class 2 Frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection).


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountClass2PBSYFrames 1.3.6.1.3.94.4.5.1.23

8 connUnitPortStatCountClass2PBSYFrames 1.3.6.1.3.94.4.5.1.23

The number of times that PBSY was returned to this port as a result of a Class 2 Frame that could not be delivered to the other end of the link. This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection).


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1007

8 connUnitPortStatCountClass2FRJTFrames 1.3.6.1.3.94.4.5.1.24

connUnitPortStatCountClass2FRJTFrames 1.3.6.1.3.94.4.5.1.24

The number of times that FRJT was returned to this port as a result of a Class 2 Frame that was rejected by the fabric.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountClass2PRJTFrames 1.3.6.1.3.94.4.5.1.25

8 connUnitPortStatCountClass2PRJTFrames 1.3.6.1.3.94.4.5.1.25

The number of times that FRJT was returned to this port as a result of a Class 2 Frame that was rejected at the destination N_Port.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1009





Return value- 80 0 0 0 0 0 0 0


53-1001156-01



The number of Class 3 Frames transmitted out this port.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1011

8 connUnitPortStatCountClass3Discards 1.3.6.1.3.94.4.5.1.28

connUnitPortStatCountClass3Discards 1.3.6.1.3.94.4.5.1.28

The number of Class 3 Frames that were discarded upon reception at this port. There is no FBSY or

FRJT generated for Class 3 Frames. They are discarded if they cannot be delivered.

This is a Fibre Channel only statistic.


53-1001156-01

connUnitPortStatCountRxMulticastObjects 1.3.6.1.3.94.4.5.1.29

8 connUnitPortStatCountRxMulticastObjects 1.3.6.1.3.94.4.5.1.29

The number of multicast frames or packets received at this port.


53-1001156-01

1013

8 connUnitPortStatCountTxMulticastObjects 1.3.6.1.3.94.4.5.1.30

connUnitPortStatCountTxMulticastObjects 1.3.6.1.3.94.4.5.1.30

The number of multicast frames or packets transmitted out this port.


53-1001156-01

connUnitPortStatCountRxBroadcastObjects 1.3.6.1.3.94.4.5.1.31

8 connUnitPortStatCountRxBroadcastObjects 1.3.6.1.3.94.4.5.1.31

The number of broadcast frames or packets received at this port. Not supported.

Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1015

8 connUnitPortStatCountTxBroadcastObjects 1.3.6.1.3.94.4.5.1.32

connUnitPortStatCountTxBroadcastObjects 1.3.6.1.3.94.4.5.1.32

The number of broadcast frames or packets transmitted out this port. On a Fibre Channel loop, count only OPNr frames generated. Not supported.

Return value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountRxLinkResets 1.3.6.1.3.94.4.5.1.33

8 connUnitPortStatCountRxLinkResets 1.3.6.1.3.94.4.5.1.33

The number of link resets. This is the number of LRs received.



53-1001156-01

1017

8 connUnitPortStatCountTxLinkResets 1.3.6.1.3.94.4.5.1.34

connUnitPortStatCountTxLinkResets 1.3.6.1.3.94.4.5.1.34

The number of link resets. This is the number LRs transmitted.



53-1001156-01

connUnitPortStatCountNumberLinkResets 1.3.6.1.3.94.4.5.1.35

8 connUnitPortStatCountNumberLinkResets 1.3.6.1.3.94.4.5.1.35

The number of link resets and LIPs detected at this port. The number times the reset link protocol is initiated. This is a count of the logical resets, a count of the number of primitives.


Return value- 80 0 0 0 0 0 0 0


53-1001156-01

1019

8 connUnitPortStatCountRxOfflineSequences 1.3.6.1.3.94.4.5.1.36

connUnitPortStatCountRxOfflineSequences 1.3.6.1.3.94.4.5.1.36

The number of offline primitive OLS received at this port.



53-1001156-01

connUnitPortStatCountTxOfflineSequences 1.3.6.1.3.94.4.5.1.37

8 connUnitPortStatCountTxOfflineSequences 1.3.6.1.3.94.4.5.1.37

The number of offline primitive OLS transmitted by this port.



53-1001156-01

1021

8 connUnitPortStatCountNumberOfflineSequences 1.3.6.1.3.94.4.5.1.38

connUnitPortStatCountNumberOfflineSequences 1.3.6.1.3.94.4.5.1.38

The number of offline primitive sequence received at this port.


Return Value- 80 0 0 0 0 0 0 0


53-1001156-01

connUnitPortStatCountLinkFailures 1.3.6.1.3.94.4.5.1.39

8 connUnitPortStatCountLinkFailures 1.3.6.1.3.94.4.5.1.39

The number of link failures. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8)



53-1001156-01

1023

8 connUnitPortStatCountInvalidCRC 1.3.6.1.3.94.4.5.1.40

connUnitPortStatCountInvalidCRC 1.3.6.1.3.94.4.5.1.40

The number of frames received with invalid CRC. This count is part of the Link Error Status Block

(LESB). (FC-PH 29.8) Loop ports should not count CRC errors passing through when monitoring.



53-1001156-01

connUnitPortStatCountInvalidTxWords 1.3.6.1.3.94.4.5.1.41

8 connUnitPortStatCountInvalidTxWords 1.3.6.1.3.94.4.5.1.41

The number of invalid transmission words received at this port. This count is part of the Link Error

Status Block (LESB). (FC-PH 29.8)



53-1001156-01

1025

8 connUnitPortStatCountPrimitiveSequenceProtocolErrors 1.3.6.1.3.94.4.5.1.42

connUnitPortStatCountPrimitiveSequenceProtocolErrors 1.3.6.1.3.94.4.5.1.42

The number of primitive sequence protocol errors detected at this port. This count is part of the

Link Error Status Block (LESB). (FC-PH 29.8)



53-1001156-01

connUnitPortStatCountLossofSignal 1.3.6.1.3.94.4.5.1.43

8 connUnitPortStatCountLossofSignal 1.3.6.1.3.94.4.5.1.43

The number of instances of signal loss detected at port.

This count is part of the Link Error Status Block (LESB).

(FC-PH 29.8)



53-1001156-01

1027

8 connUnitPortStatCountLossofSynchronization 1.3.6.1.3.94.4.5.1.44

connUnitPortStatCountLossofSynchronization 1.3.6.1.3.94.4.5.1.44

The number of instances of synchronization loss detected at port. This count is part of the Link

Error Status Block (LESB). (FC-PH 29.8)



53-1001156-01

connUnitPortStatCountInvalidOrderedSets 1.3.6.1.3.94.4.5.1.45

8 connUnitPortStatCountInvalidOrderedSets 1.3.6.1.3.94.4.5.1.45

The number of invalid ordered sets received at port. This count is part of the Link Error Status Block

(LESB). (FC-PH 29.8).



53-1001156-01

1029

8 connUnitPortStatCountFramesTooLong 1.3.6.1.3.94.4.5.1.46

connUnitPortStatCountFramesTooLong 1.3.6.1.3.94.4.5.1.46

The number of frames received at this port where the frame length was greater than what was agreed to in FLOGI/PLOGI. This could be caused by losing the end of frame delimiter.



53-1001156-01

connUnitPortStatCountFramesTruncated 1.3.6.1.3.94.4.5.1.47

8 connUnitPortStatCountFramesTruncated 1.3.6.1.3.94.4.5.1.47

The number of frames received at this port where the frame length was less than the minimum indicated by the frame header - normally 24 bytes, but it could be more if the DFCTL field indicates an optional header should have been present.



53-1001156-01

1031

8 connUnitPortStatCountAddressErrors 1.3.6.1.3.94.4.5.1.48

connUnitPortStatCountAddressErrors 1.3.6.1.3.94.4.5.1.48

The number of frames received with unknown addressing. For example, unknown SID or DID. The

SID or DID is not known to the routing algorithm.



53-1001156-01

connUnitPortStatCountDelimiterErrors 1.3.6.1.3.94.4.5.1.49

8 connUnitPortStatCountDelimiterErrors 1.3.6.1.3.94.4.5.1.49

The number of invalid frame delimiters received at this port. An example is a frame with a class 2 start and a class 3 at the end.



53-1001156-01

1033

8 connUnitPortStatCountEncodingDisparityErrors 1.3.6.1.3.94.4.5.1.50

connUnitPortStatCountEncodingDisparityErrors 1.3.6.1.3.94.4.5.1.50

The number of disparity errors received at this port.


Service Group


Implementation of the Service group is mandatory for all systems.

The Service group contains the following subgroups.

•

Connectivity Unit Service Scalers Group

•

Connectivity Unit Service Tables Group

Implementation of the Connectivity Unit Service Scalers group is mandatory for all systems.


53-1001156-01

connUnitSnsMaxEntry 1.3.6.1.3.94.5.1.1

The maximum number of entries in the table. connUnitSnsMaxEntry 1.3.6.1.3.94.5.1.1

8


53-1001156-01

1035

8 connUnitSnsTable 1.3.6.1.3.94.5.2.1

connUnitSnsTable 1.3.6.1.3.94.5.2.1

This table contains an entry for each object registered with this port in the switch.

Implementation of the Connectivity Unit Service Tables group is mandatory for all systems.

A Brocade Access Gateway has no name server information; therefore this table is disabled.


53-1001156-01

connUnitSnsEntry 1.3.6.1.3.94.5.2.1.1

8 connUnitSnsEntry 1.3.6.1.3.94.5.2.1.1

Index

The simple name server (SNS) table for the port represented by connUnitSnsPortIndex.

connUnitSnsId connUnitSnsPortIndex connUnitSnsPortIdentifier


53-1001156-01

1037

8 connUnitSnsId 1.3.6.1.3.94.5.2.1.1.1

connUnitSnsId 1.3.6.1.3.94.5.2.1.1.1

The connUnitId of the connectivity unit that contains this name server table.


53-1001156-01

connUnitSnsPortIndex 1.3.6.1.3.94.5.2.1.1.2

8 connUnitSnsPortIndex 1.3.6.1.3.94.5.2.1.1.2

The physical port number of this SNS table entry. Each physical port has an SNS table with 1-n entries indexed by connUnitSnsPortIdentifier (port address).

Chassis switches containing the FC4-16IP blade will have eight GbE ports and treated as iSCSI

Virtual Initiator. These ports will be part of the name server (NS) database. connUnitTable will display each of these ports as a separate NS entry. Because no user ports are associated to GbE ports/virtual initiators, the connUnitSnsPortIndex for virtual initiators is shown as 999.


53-1001156-01

1039

8 connUnitSnsPortIdentifier 1.3.6.1.3.94.5.2.1.1.3

connUnitSnsPortIdentifier 1.3.6.1.3.94.5.2.1.1.3

The port identifier for this entry in the SNS table.


53-1001156-01

connUnitSnsPortName 1.3.6.1.3.94.5.2.1.1.4

8 connUnitSnsPortName 1.3.6.1.3.94.5.2.1.1.4

The port name for this entry in the SNS table.


53-1001156-01

1041

8 connUnitSnsNodeName 1.3.6.1.3.94.5.2.1.1.5

connUnitSnsNodeName 1.3.6.1.3.94.5.2.1.1.5

The node name for this entry in the SNS table.


53-1001156-01

connUnitSnsClassOfSvc 1.3.6.1.3.94.5.2.1.1.6

8 connUnitSnsClassOfSvc 1.3.6.1.3.94.5.2.1.1.6

The Classes of Service offered by this entry in the SNS table.


53-1001156-01

1043

8 connUnitSnsNodeIPAddress 1.3.6.1.3.94.5.2.1.1.7

connUnitSnsNodeIPAddress 1.3.6.1.3.94.5.2.1.1.7

The IPv6 formatted address of the Node for this entry in the SNS table.


53-1001156-01

connUnitSnsProcAssoc 1.3.6.1.3.94.5.2.1.1.8

8 connUnitSnsProcAssoc 1.3.6.1.3.94.5.2.1.1.8

The process associator for this entry in the SNS table.

Hard coded to FF.


53-1001156-01

1045

8 connUnitSnsFC4Type 1.3.6.1.3.94.5.2.1.1.9

connUnitSnsFC4Type 1.3.6.1.3.94.5.2.1.1.9

The FC-4 types supported by this entry in the SNS table.


53-1001156-01

connUnitSnsPortType 1.3.6.1.3.94.5.2.1.1.10

8 connUnitSnsPortType 1.3.6.1.3.94.5.2.1.1.10

The port type of this entry in the SNS table.


53-1001156-01

1047

8 connUnitSnsPortIPAddress 1.3.6.1.3.94.5.2.1.1.11

connUnitSnsPortIPAddress 1.3.6.1.3.94.5.2.1.1.11

The IPv6 formatted address of this entry in the SNS table.


53-1001156-01

connUnitSnsFabricPortName 1.3.6.1.3.94.5.2.1.1.12

8 connUnitSnsFabricPortName 1.3.6.1.3.94.5.2.1.1.12

The fabric port name of this entry in the SNS table.


53-1001156-01

1049

8 connUnitSnsHardAddress 1.3.6.1.3.94.5.2.1.1.13

connUnitSnsHardAddress 1.3.6.1.3.94.5.2.1.1.13

The hard address of this entry in the SNS table.


53-1001156-01

connUnitSnsSymbolicPortName 1.3.6.1.3.94.5.2.1.1.14

8 connUnitSnsSymbolicPortName 1.3.6.1.3.94.5.2.1.1.14

The symbolic port name of this entry in the SNS table. If the attached device has only the symbolicPortName, the symbolicPortName is shown and the symbolicNodeName appears as "null".


53-1001156-01

1051

8 connUnitSnsSymbolicNodeName 1.3.6.1.3.94.5.2.1.1.15

connUnitSnsSymbolicNodeName 1.3.6.1.3.94.5.2.1.1.15

The symbolic node name of this entry in the SNS table. If the attached device has only the symbolicNodename, the symbolicNodename is shown and the symbolicPortname appears as

"null".


53-1001156-01

SNMP Trap Registration Group

SNMP Trap Registration Group

trapMaxClients 1.3.6.1.3.94.2.1

The maximum number of SNMP trap recipients supported by the connectivity unit.

Set to 6.

8


53-1001156-01

1053

8 trapClientCount 1.3.6.1.3.94.2.2

trapClientCount 1.3.6.1.3.94.2.2

The current number of rows in the trap table.


53-1001156-01

trapRegTable 1.3.6.1.3.94.2.3

8 trapRegTable 1.3.6.1.3.94.2.3

A table containing a row for each IP address/port number to which traps are sent.


53-1001156-01

1055

8 trapRegEntry 1.3.6.1.3.94.2.3.1

trapRegEntry 1.3.6.1.3.94.2.3.1

Index

IP/port pair for a specific client. trapRegIpAddress trapRegPort


53-1001156-01

trapRegIpAddress 1.3.6.1.3.94.2.3.1.1

The IP address of a client registered for traps.

trapRegIpAddress 1.3.6.1.3.94.2.3.1.1

8


53-1001156-01

1057

8 trapRegPort 1.3.6.1.3.94.2.3.1.2

trapRegPort 1.3.6.1.3.94.2.3.1.2

The UDP port to send traps to for this host. Normally this would be the standard trap port (162).

This object is an index and must be specified to create a row in this table.

Set to 162.


53-1001156-01

trapRegFilter 1.3.6.1.3.94.2.3.1.3

8 trapRegFilter 1.3.6.1.3.94.2.3.1.3

This value defines the trap severity filter for this trap host. The connUnit sends traps to this host that have a severity level less than or equal to this value. The default value of this object is Warning.

The mapping between errorlog severity level and this variable is:

TABLE 22

System Error Log errshow command

FA-MIB none (0)

Critical (1)

Error (2)

Warning (3)

Info (4)

Debug (5) unknown (1) critical (4) error (5) warning (6)

info (8) debug (9)

This severity applies to all entries. Refer to

FcEventSeverity in

Table 20 on page 879.

The values 1, 3, 7, and 10 are not valid for SET operations.


53-1001156-01

1059

8 trapRegRowState 1.3.6.1.3.94.2.3.1.4

trapRegRowState 1.3.6.1.3.94.2.3.1.4

Specifies the state of the row. This entry always returns rowActive and allows for read-only.

TABLE 23

TrapRegRowState for Read/Write

State rowDestroy (1) rowInactive (2) rowActive (3)

Description (Read) Description (Write)

Read- Can never happen.

Read- Indicates that this row does exist but that traps are not enabled to be sent to the target.

Read- Indicates that this row exists and that traps are enabled to be sent to the target.

Write- Remove this row from the table.

Write- If the row does not exist and the agent allows writes to the trap table, then a new row is created. The values of the optional columns are set to default values. Traps are not enabled to be sent to the target.

If the row already existed, then traps are disabled from being sent to the target.

Write- If the row does not exist and the agent allows writes to the trap table, then a new row is created. The values of the optional columns are set to default values. Traps are enabled to be sent to the target. If the row already exists, then traps are enabled to be sent to the target.


53-1001156-01

Revision Number Scalar

8

Revision Number Scalar

revisionNumber 1.3.6.1.3.94.3

This is the revision number for this MIB. The format of the revision value is as follows:

0 = High order major revision number

1 = Low order major revision number

2 = High order minor revision number

3 = Low order minor revision number

The value is stored as an ASCII value. The following is the current value of this object.

0 = 0

1 = 3

2 = 0

3 = 0

This defines a revision of 03.00.

Set to 0300.

Unsupported Tables

The Connectivity Unit Port Statistics Fabric Table (connUnitPortStatTable) is supported in v6.0, v5.x, and v2.6.1.

Brocade does not support the following:

•

Connectivity Unit Port Statistics Hub Table

•

Connectivity Unit Port Statistics SCSI Table

•

Connectivity Unit Port Statistics LAN/WAN Table


53-1001156-01

1061

8

FibreAlliance MIB Traps

FibreAlliance MIB Traps

connUnitStatusChange

Enterprise

Variables fcmgmt connUnitStatus, connUnitState

The overall status of the connectivity unit has changed.

Recommended severity level (for filtering)- alert.

Generated when connUnitStatus changes. Refer to

“connUnitStatus 1.3.6.1.3.94.1.6.1.6” on page 891 for a description of how the value is calculated.

Sample trap output for Fabric OS v6.1.0connUnitStatus.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.1 = warning(4) connUnitState.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.1 = offline(3)

Refer to the Fabric Watch Administrator’s Guide on how the switch status is determined.


53-1001156-01

connUnitDeletedTrap

Enterprise

Variables fcmgmt connUnitId

A connUnit has been deleted from this agent.

Recommended severity level (for filtering)- warning.

Not implemented.

connUnitDeletedTrap

8


53-1001156-01

1063

8 connUnitEventTrap connUnitEventTrap

Enterprise

Variables fcmgmt connUnitEventId, connUnitEventType, connUnitEventObject, connUnitEventDescr

An event has been generated by the connectivity unit.

Recommended severity level (for filtering)- info.

Sample trap output for Fabric OS v6.1.0connUnitEventId.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.354 = 354 connUnitEventType.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.354 = other(2) connUnitEventObject.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.354 = null connUnitEventDescr.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.354 = FW-1425

Switch status changed from MARGINAL to HEALTHY.

Refer to the swEventTrap for more details.


53-1001156-01

connUnitSensorStatusChange

8 connUnitSensorStatusChange

Enterprise

Variables fcmgmt connUnitSensorStatus

Overall status of the connectivity unit has changed.

This trap is generated whenever the status of the sensors (like fan, power supply, temperature) present in the connectivity unit changes.

Sample trap output for Fabric OS v6.1.0.

connUnitSensorStatus.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.7 = failed(5)

Refer to the Fabric Watch Administrator’s Guide for information on configuring thresholds that generate these traps.


53-1001156-01

1065

8 connUnitPortStatusChange connUnitPortStatusChange

Enterprise

Variables fcmgmt connUnitPortStatus, connUnitPortState

Overall status of the connectivity unit changed. Recommended severity level (for filtering)- alert.

This trap sends the instance of connUnitPortName as part of the trap; the instance string is NULL, if the port name is not defined for the specified port.

Sample trap output for Fabric OS v6.1.0.

connUnitPortStatus.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.29 = ready(3) connUnitPortState.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.29 = online(2) connUnitPortName.16.0.0.96.105.144.109.136.0.0.0.0.0.0.0.0.29 = test

Refer to the swFCportSCN for more information.


53-1001156-01

FCIP MIB Objects

Chapter

9

This chapter contains descriptions and other information specific to iSCSI MIB object types, including the following.

•

FCIP MIB Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067

•

fcipEntityInstanceTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1070

•

fcipLinkTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1079

•

FCIP Extended Link Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1092

FCIP MIB Overview

The descriptions of each of the FCIP MIB variables in this chapter come directly from the MIB itself.


The following FCIP MIB tables are supported.

•

FCIP entity instance table

•

FCIP link table

•

FCIP extended link table

The FCIP entity instance table (fcipEntityInstanceTable) and the FCIP link table (fcipLinkTable) are


53-1001156-01

1067

9

FCIP MIB Overview

FCIP MIB System Organization of MIB Objects

Figure 68 , Figure 69 , Figure 70

, and Figure 71

depict the high level organization of the FCIP MIB relevant to the supported tables. Refer to RFC4044 for a description of the entire MIB.

- iso

- org

- dod

- internet

- experimental

- mgmt

- mib-2

- fcipMIB 1.3.6.1.2.1.224

- fcipObjects

- fcipconfig

+ fcipEntityInstanceTable .4

+ fcipLinkTable .5

FIGURE 68

High Level Organization

- fcipEntityInstanceEntry 1.3.6.1.2.1.224.1.1.4.1

fcipEntityId 1.3.6.1.2.1.224.1.1.4.1.1

fcipEntityAddressType 1.3.6.1.2.1.224.1.1.4.1.3

fcipEntityAddress 1.3.6.1.2.1.224.1.1.4.1.4

fcipEntityTcpConnPort 1.3.6.1.2.1.224.1.1.4.1.5

fcipEntitySeqNumWrap 1.3.6.1.2.1.224.1.1.4.1.6

ifcipEntityPHBSupport 1.3.6.1.2.1.224.1.1.4.1.7

fcipEntityStatus 1.3.6.1.2.1.224.1.1.4.1.8

FIGURE 69

ifcipEntityInstanceTable Hierarchy

- fcipLinkEntry 1.3.6.1.2.1.224.1.1.5.1

fcipLinkIndex 1.3.6.1.2.1.224.1.1.5.1.1

fcipLinkIfIndex 1.3.6.1.2.1.224.1.1.5.1.2

fcipLinkCost 1.3.6.1.2.1.224.1.1.5.1.3

fcipLinkLocalFcipEntityMode 1.3.6.1.2.1.224.1.1.5.1.4

fcipLinkLocalFcipEntityAddressType 1.3.6.1.2.1.224.1.1.5.1.5

fcipLinkLocalFcipEntityAddress 1.3.6.1.2.1.224.1.1.5.1.6

fcipLinkRemFcipEntityWWN 1.3.6.1.2.1.224.1.1.5.1.7

fcipLinkRemFcipEntityId 1.3.6.1.2.1.224.1.1.5.1.8

fcipLinkRemFcipEntityAddressType 1.3.6.1.2.1.224.1.1.5.1.9

fcipLinkRemFcipEntityAddress 1.3.6.1.2.1.224.1.1.5.1.10

fcipLinkStatus 1.3.6.1.2.1.224.1.1.5.1.11

fcipLinkCreateTime 1.3.6.1.2.1.224.1.1.5.1.12

FIGURE 70

fcipLinkTable Hierarchy

- fcipExtendedLinkEntry 1.3.6.1.4.1.1588.4.1.1

fcipExtendedLinkIfIndex 1.3.6.1.4.1.1588.4.1.1.1

fcipExtendedLinkTcpRetransmits 1.3.6.1.4.1.1588.4.1.1.2

fcipExtendedLinkTcpDropped Packets 1.3.6.1.4.1.1588.4.1.1.3

fcipExtendedLinkCompressionRatio 1.3.6.1.4.1.1588.4.1.1.4

fcipExtendedLinkTcpSmoothedRTT 1.3.6.1.4.1.1588.4.1.1.5

fcipExtendedLinkRawBytes 1.3.6.1.4.1.1588.4.1.1.6

fcipExtendedLinkCompressedBytes 1.3.6.1.4.1.1588.4.1.1.7

fcipExtendedLinkConnectedCount 1.3.6.1.4.1.1588.4.1.1.8

fcipExtendedLinkRtxRtxTO 1.3.6.1.4.1.1588.4.1.1.9

fcipExtendedLinkRtxDupAck 1.3.6.1.4.1.1588.4.1.1.10

fcipExtendedLinkDupAck 1.3.6.1.4.1.1588.4.1.1.11


53-1001156-01

FCIP MIB Overview

9

fcipExtendedLinkRtt 1.3.6.1.4.1.1588.4.1.1.12

fcipExtendedLinkOoo 1.3.6.1.4.1.1588.4.1.1.13

fcipExtendedLinkSlowStarts 1.3.6.1.4.1.1588.4.1.1.14

FIGURE 71

fcipExtendedLinkTable


53-1001156-01

1069

9 fcipEntityInstanceTable

fcipEntityInstanceTable

The fcipEntityInstancetable has an entry for each configured IP interface. The fcipEntryId is used to index the FCIP Extended link table, along with the fcipLinkIndex from the FCIP Link Table

(fcipLinkTable).


53-1001156-01

fcipEntityInstanceEntry 1.3.6.1.2.1.224.1.1.4.1

9 fcipEntityInstanceEntry 1.3.6.1.2.1.224.1.1.4.1

An fcipEntityInstanceEntry is an entry in the fcipEntityInstanceTable that represents an IP interface configured on a 7500 or on an FC4-18i blade. There is an entry for each configured IP interface. An fcipEntityInstanceEntry comprises the following elements.

•

fcipEntityId 1.3.6.1.2.1.224.1.1.4.1.1

•

fcipEntityName 1.3.6.1.2.1.224.1.1.4.1.2

•


•


•


•


•


•



53-1001156-01

1071

9 fcipEntityId 1.3.6.1.2.1.224.1.1.4.1.1

fcipEntityId 1.3.6.1.2.1.224.1.1.4.1.1

The FCIP entity indentifier.


53-1001156-01

fcipEntityName 1.3.6.1.2.1.224.1.1.4.1.2

9 fcipEntityName 1.3.6.1.2.1.224.1.1.4.1.2

An administratively assigned name for the fcip entity.

Example- IP interface on gigE 0 port.


53-1001156-01

1073

9 fcipEntityAddressType 1.3.6.1.2.1.224.1.1.4.1.3


The type of Internet address by which the entity is reachable. Only address types IPv4 and IPv6 are supported

.


53-1001156-01


9 fcipEntityAddress 1.3.6.1.2.1.224.1.1.4.1.4

The Internet address for the entity, if configured. The format of this address is determined by the value of the fcipEntityAddressType object.


53-1001156-01

1075

9 fcipEntityTcpConnPort 1.3.6.1.2.1.224.1.1.4.1.5


A TCP port other than the FCIP Well-Known port on which the FCIP entity listens for new TCP connection requests. It contains the value zero (0) if the FCIP Entity only listens on the Well-Known port. The default is 0.

Not used.


53-1001156-01


9 fcipEntitySeqNumWrap 1.3.6.1.2.1.224.1.1.4.1.6

An indication of whether the FCIP Entity supports protection against sequence number wrap

Not used.


53-1001156-01

1077

9 ifcipEntityPHBSupport 1.3.6.1.2.1.224.1.1.4.1.7


An indication of whether the FCIP Entity supports PHB IP quality of service (QoS).

Not Used.


53-1001156-01


9 fcipEntityStatus 1.3.6.1.2.1.224.1.1.4.1.8

This object specifies the operational status of the row. When a management station sets the status to active(1), then the values for the objects fcipEntityName, fcipEntityAddressType, and fcipEntityAddress should be supplied as part of the set request. The values of the objects fcipEntityName, fcipEntityAddressType, and fcipEntityAddress can be changed if the row status is in active state. The object fcipEntityTcpConnPort takes the default value zero(0), if no value is supplied at the time of row creation. Setting the status to destroy (6) deletes the specified FCIP entity instance row from the table. It also deletes all the rows corresponding to the specified FCIP entity from the fcipLinkTable and fcipTcpConnTable tables

.

fcipLinkTable

This table contains information about FCIP links that exist on this device. There is an entry for each

FCIP tunnel. The fcipLinkIndex is used to index the FCIP extended link table, along with the fcipEntryId from the FCIP entity instance table (fcipEntityInstanceTable).


53-1001156-01

1079

9 fcipLinkEntry 1.3.6.1.2.1.224.1.1.5.1

fcipLinkEntry 1.3.6.1.2.1.224.1.1.5.1

A conceptual row of the FCIP link table containing information about a particular FCIP link. The values of the read-create objects in this table are persistent across system restarts.

The following comprise an fcipLinkEntry.

•

fcipLinkIndex 1.3.6.1.2.1.224.1.1.5.1.1

•


•

fcipLinkCost 1.3.6.1.2.1.224.1.1.5.1.3

•


•


•


•


•


•


•


•

fcipLinkStatus 1.3.6.1.2.1.224.1.1.5.1.11

•



53-1001156-01

fcipLinkIndex 1.3.6.1.2.1.224.1.1.5.1.1

9 fcipLinkIndex 1.3.6.1.2.1.224.1.1.5.1.1

An integer that uniquely identifies one FCIP link within an FCIP entity.


53-1001156-01

1081

9 fcipLinkIfIndex 1.3.6.1.2.1.224.1.1.5.1.2


The ifIndex value of the virtual interface corresponding to the FCIP Link running over TCP/IP. This is the same as the ifIndex value in the ifTable for the ifType of fcipLink.


53-1001156-01

fcipLinkCost 1.3.6.1.2.1.224.1.1.5.1.3

9 fcipLinkCost 1.3.6.1.2.1.224.1.1.5.1.3

The FSPF cost associated with this FCIP Link. The default is 0.


53-1001156-01

1083

9 fcipLinkLocalFcipEntityMode 1.3.6.1.2.1.224.1.1.5.1.4


The mode of the local end of the FCIP link.


53-1001156-01


9 fcipLinkLocalFcipEntityAddressType 1.3.6.1.2.1.224.1.1.5.1.5

The type of Internet address contained in the corresponding instance of fcipLinkLocalFcipEntityAddress. Only address types IPv4 and IPv6 are supported.


53-1001156-01

1085

9 fcipLinkLocalFcipEntityAddress 1.3.6.1.2.1.224.1.1.5.1.6


The Internet address for the local end of this FCIP Link. The format of this object is determined by the value of the fcipLinkLocalFcipEntityAddressType object.


53-1001156-01


9 fcipLinkRemFcipEntityWWN 1.3.6.1.2.1.224.1.1.5.1.7

The World Wide Name of the remote FC Fabric Entity

.


53-1001156-01

1087

9 fcipLinkRemFcipEntityId 1.3.6.1.2.1.224.1.1.5.1.8


The identifier for the remote FCIP entity.


53-1001156-01


9 fcipLinkRemFcipEntityAddressType 1.3.6.1.2.1.224.1.1.5.1.9

The type of Internet address contained in the corresponding instance of fcipLinkRemFcipEntityAddress. Only address types IPv4 and IPv6 are supported.


53-1001156-01

1089

9 fcipLinkRemFcipEntityAddress 1.3.6.1.2.1.224.1.1.5.1.10


The Internet address for the remote end of this FCIP Link. The format of this object is determined by the value of the fcipLinkRemFcipEntityAddressType object.


53-1001156-01

fcipLinkStatus 1.3.6.1.2.1.224.1.1.5.1.11

9 fcipLinkStatus 1.3.6.1.2.1.224.1.1.5.1.11

This object specifies the operational status of the row. The values of objects fcipLinkLocalFcipEntityAddressType, fcipLinkLocalFcipEntityAddress, fcipLinkRemFcipEntityWWN, fcipLinkRemFcipEntityId, fcipLinkRemFcipEntityAddressType, and fcipLinkRemFcipEntityAddress can be changed if the row is in active(1) state. The object fcipLinkCost is set to the value zero(0) if no value is supplied at the time of row creation. Setting the status to destroy(6) deletes the specified FCIP link from the table. It also deletes all rows corresponding to the specified FCIP link from the fcipTcpConnTable table.


53-1001156-01

1091

9 fcipLinkCreateTime 1.3.6.1.2.1.224.1.1.5.1.12


The value of sysUpTime when this entry was last created

FCIP Extended Link Table

The FCIP Extended Link Table contains statisical information about FCIP tunnel transport operation. The information stored in this table is returned in response to portshow fciptunnel commands. The table contains the following.

•


•


•


•


•


•


•


•


•


•


•


•


•


•



53-1001156-01


9 fcipExtendedLinkIfIndex 1.3.6.1.4.1.1588.4.1.1.1

The ifIndex value of the virtual interface corresponding to the FCIP Link running over TCP/IP.


53-1001156-01

1093

9 fcipExtendedLinkTcpRetransmits 1.3.6.1.4.1.1588.4.1.1.2


A counter containing the number of retransmitted segments for an FC data transfer over an FCIP tunnel.


53-1001156-01



A counter containing the number of packets lost for FC control traffic and data transfer over an

FCIP tunnel.

9


53-1001156-01

1095

9 fcipExtendedLinkCompressionRatio 1.3.6.1.4.1.1588.4.1.1.4


The ratio between compressed bytes and raw bytes over an FCIP tunnel.


53-1001156-01


9 fcipExtendedLinkTcpSmoothedRTT 1.3.6.1.4.1.1588.4.1.1.5

The round trip time (latency) in milleseconds for a transfer over an FCIP tunnel.


53-1001156-01

1097

9 fcipExtendedLinkRawBytes 1.3.6.1.4.1.1588.4.1.1.6


The total number of raw bytes sent or received.


53-1001156-01


9 fcipExtendedLinkCompressedBytes 1.3.6.1.4.1.1588.4.1.1.7

The total number of compressed bytes received over an FCIP tunnel.


53-1001156-01

1099

9 fcipExtendedLinkConnectedCount 1.3.6.1.4.1.1588.4.1.1.8


The total number of TCP session connection.


53-1001156-01


9 fcipExtendedLinkRtxRtxTO 1.3.6.1.4.1.1588.4.1.1.9

A counter containing retransmit packets due to timeout.


53-1001156-01

1101

9 fcipExtendedLinkRtxDupAck 1.3.6.1.4.1.1588.4.1.1.10


A counter containing retransmit packets due to duplicate acknowledgement.


53-1001156-01


9 fcipExtendedLinkDupAck 1.3.6.1.4.1.1588.4.1.1.11

A counter containing duplicate acknowledgement packets.


53-1001156-01

1103

9 fcipExtendedLinkRtt 1.3.6.1.4.1.1588.4.1.1.12


The round trip time in milliseconds.


53-1001156-01


9 fcipExtendedLinkOoo 1.3.6.1.4.1.1588.4.1.1.13

A counter containing TCP out-of-order.


53-1001156-01

1105

9 fcipExtendedLinkSlowStarts 1.3.6.1.4.1.1588.4.1.1.14


A counter containing slow starts.


53-1001156-01

iSCSI MIB Objects

Chapter

10

This chapter contains descriptions and other information specific to iSCSI MIB object types, including the following.

•

iSCSI MIB Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1107

•

iscsiInstanceAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1111

•

iscsiNodeAttributesTable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125

•

iscsiSessionAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145

•

iscsiSessionStatsTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1168

•

iscsiConnectionAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1176

iSCSI MIB Overview

The descriptions of each of the iSCSI MIB variables in this chapter come directly from the MIB itself.


The following iSCSI MIB tables are supported.

• iSCSI Instance Attributes table

• iSCSI Node Attributes table

• iSCSI Session Attributes table

• iSCSI Session Statisitics table

• iSCSI Connection Attributes table


53-1001156-01

1107

10 iSCSI MIB Overview

iSCSI MIB System Organization of MIB Objects

Figure 72 to

Figure 77

depict the high level organization of the iSCSI MIB relevant to the supported tables. Refer to RFC4544 for a description of the entire MIB.

- iso

- org

- dod

- internet

- experimental

- mgmt

- mib-2

- iscsimibmodule

- iscsiObjects

- iscsiInstance

+ iscsiInstanceAttributesTable

- iscsiPortal

- iscsiTargetPortal

- iscsiInitiatorPortal

- iscsiNode

+ iscsiNodeAttributesTable

- iscsiTarget

- iscsiTgtAuthorization

- iscsiInitiator

- iscsiIntrAuthorization

- iscsiSession

+ iscsiSessionAttributesTable

+ iscsiSessionStatsTable

- iscsiConnection

+ isciConnectionAttributesTable

FIGURE 72

High Level Organization

- iscsiInstanceAttributesEntry

iscsiInstIndex 1.3.6.1.2.1.142.1.1.1.1.1

iscsiInstDescr 1.3.6.1.2.1.142.1.1.1.1.2

iscsiInstVersionMin 1.3.6.1.2.1.142.1.1.1.1.3

iscsiInstVersionMax 1.3.6.1.2.1.142.1.1.1.1.4

iscsiInstVendorID 1.3.6.1.2.1.142.1.1.1.1.5

iscsiInstVendorVersion 1.3.6.1.2.1.142.1.1.1.1.6

iscsiInstPortalNumber 1.3.6.1.2.1.142.1.1.1.1.7

iscsiInstNodeNumber 1.3.6.1.2.1.142.1.1.1.1.8

iscsiInstSessionNumber 1.3.6.1.2.1.142.1.1.1.1.9

iscsiInstSsnFailures 1.3.6.1.2.1.142.1.1.1.1.10

iscsiInstLastSsnFailureType 1.3.6.1.2.1.142.1.1.1.1.11

iscsiInstLastSsnRmtNodeName 1.3.6.1.2.1.142.1.1.1.1.12

iscsiInstDiscontinuityTime 1.3.6.1.2.1.142.1.1.1.1.13

FIGURE 73

iscsiInstanceAttributesTable Hierarchy


53-1001156-01


53-1001156-01

iSCSI MIB Overview

10

- iscsiNodesAttributesEntry

iscsiNodeIndex 1.3.6.1.2.1.142.1.1.5.1.1.1

iscsiNodeName 1.3.6.1.2.1.142.1.1.5.1.1.2

iscsiNodeAlias 1.3.6.1.2.1.142.1.1.5.1.1.3

iscsiNodeRoles 1.3.6.1.2.1.142.1.1.5.1.1.4

iscsiNodeTransportType 1.3.6.1.2.1.142.1.1.5.1.1.5

iscsiNodeInitialR2T 1.3.6.1.2.1.142.1.1.5.1.1.6

iscsiNodeImmediateData 1.3.6.1.2.1.142.1.1.5.1.1.7

iscsiNodeMaxOutstandingR2T 1.3.6.1.2.1.142.1.1.5.1.1.8

iscsiNodeFirstBurstLength 1.3.6.1.2.1.142.1.1.5.1.1.9

iscsiNodeMaxBurstLength 1.3.6.1.2.1.142.1.1.5.1.1.10

iscsiNodeMaxConnections 1.3.6.1.2.1.142.1.1.5.1.1.11

iscsiNodeDataSequenceInOrder 1.3.6.1.2.1.142.1.1.5.1.1.12

iscsiNodeDataPDUInOrder 1.3.6.1.2.1.142.1.1.5.1.1.13

iscsiNodeDefaultTime2Wait 1.3.6.1.2.1.142.1.1.5.1.1.14

iscsiNodeDefaultTime2Retain 1.3.6.1.2.1.142.1.1.5.1.1.15

iscsiNodeErrorRecoveryLevel 1.3.6.1.2.1.142.1.1.5.1.1.16

iscsiNodeDiscontinuityTime 1.3.6.1.2.1.142.1.1.5.1.1.17

iscsiNodeStorageType 1.3.6.1.2.1.142.1.1.5.1.1.18

FIGURE 74

iscsiNodeAttributesTable Hierarchy

- iscsiSessionsAttributesEntry

iscsiSsnNodeIndex 1.3.6.1.2.1.142.1.1.10.1.1.1

iscsiSsnIndex 1.3.6.1.2.1.142.1.1.10.1.1.2

iscsiSsnDirection 1.3.6.1.2.1.142.1.1.10.1.1.3

iscsiSsnInitiatorName 1.3.6.1.2.1.142.1.1.10.1.1.4

iscsiSsnTargetName 1.3.6.1.2.1.142.1.1.10.1.1.5

iscsiSsnTSIH 1.3.6.1.2.1.142.1.1.10.1.1.6

iscsiSsnISID 1.3.6.1.2.1.142.1.1.10.1.1.7

iscsiSsnInitiatorAlias 1.3.6.1.2.1.142.1.1.10.1.1.8

iscsiSsnTargetAlias 1.3.6.1.2.1.142.1.1.10.1.1.9

iscsiSsnInitialR2T 1.3.6.1.2.1.142.1.1.10.1.1.10

iscsiSsnImmediateData 1.3.6.1.2.1.142.1.1.10.1.1.11

iscsiSsnType 1.3.6.1.2.1.142.1.1.10.1.1.12

iscsiSsnMaxOutstandingR2T 1.3.6.1.2.1.142.1.1.10.1.1.13

iscsiSsnFirstBurstLength 1.3.6.1.2.1.142.1.1.10.1.1.14

iscsiSsnMaxBurstLength 1.3.6.1.2.1.142.1.1.10.1.1.15

iscsiSsnConnectionNumber 1.3.6.1.2.1.142.1.1.10.1.1.16

iscsiSsnAuthIdentity 1.3.6.1.2.1.142.1.1.10.1.1.17

iscsiSsnDataSequenceInOrder 1.3.6.1.2.1.142.1.1.10.1.1.18

iscsiSsnDataPDUInOrder 1.3.6.1.2.1.142.1.1.10.1.1.19

iscsiSsnErrorRecoveryLevel 1.3.6.1.2.1.142.1.1.10.1.1.20

iscsiSsnErrorDiscontinuityTime 1.3.6.1.2.1.142.1.1.10.1.1.21

FIGURE 75

iscsiSessionAttributesTable Hierarchy

1109

10 iSCSI MIB Overview

- iscsiSessionsStatsEntry

iscsiSsnCmdPDUs 1.3.6.1.2.1.142.1.1.10.2.1.1

iscsiSsnRspPDUs 1.3.6.1.2.1.142.1.1.10.2.1.2

iscsiTxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.3

iscsiRxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.4

iscsiLCTxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.5

iscsiLCRxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.6

FIGURE 76

iscsi SessionStatsTable Hierarchy

- iscsiConnectionAttributesEntry

iscsiCxnIndex 1.3.6.1.2.1.142.1.1.11.1.1.1

iscsiCxnCid 1.3.6.1.2.1.142.1.1.11.1.1.2

iscsiCxnState 1.3.6.1.2.1.142.1.1.11.1.1.3

iscsiCxnAddrType 1.3.6.1.2.1.142.1.1.11.1.1.4

iscsiCxnLocalAddr 1.3.6.1.2.1.142.1.1.11.1.1.5

iscsiCxnProtocol 1.3.6.1.2.1.142.1.1.11.1.1.6

iscsiCxnLocalPort 1.3.6.1.2.1.142.1.1.11.1.1.7

iscsiCxnRemoteAddr 1.3.6.1.2.1.142.1.1.11.1.1.8

iscsiCxnRemotePort 1.3.6.1.2.1.142.1.1.11.1.1.9

iscsiCxnMaxRecvDataSegLength 1.3.6.1.2.1.142.1.1.11.1.1.10

iscsiCxnMaxXmitDataSegLength 1.3.6.1.2.1.142.1.1.11.1.1.11

iscsiCxnHeaderIntegrity 1.3.6.1.2.1.142.1.1.11.1.1.12

iscsiCxnDataIntegrity 1.3.6.1.2.1.142.1.1.11.1.1.13

iscsiCxnRecvMarker 1.3.6.1.2.1.142.1.1.11.1.1.14

iscsiCxnSendMarker 1.3.6.1.2.1.142.1.1.11.1.1.15

iscsiCxnVersionActive 1.3.6.1.2.1.142.1.1.11.1.1.16

FIGURE 77

iscsiConnectionAttributesTable Hierarchy


53-1001156-01

iscsiInstanceAttributesTable

10

iscsiInstanceAttributesTable

The iscsiInstanceAttributesTable is the primary table of the iSCSI MIB module. Every table entry is owned by exactly one iSCSI instance.


53-1001156-01

1111

10 iscsiInstanceAttributesEntry iscsiInstanceAttributesEntry

An isciInstanceAttributesEntry comprises the following attributes.

•

iscsiInstIndex 1.3.6.1.2.1.142.1.1.1.1.1

•

iscsiInstDescr 1.3.6.1.2.1.142.1.1.1.1.2

•


•


•


•


•


•


•


•


•


•


•



53-1001156-01

iscsiInstIndex 1.3.6.1.2.1.142.1.1.1.1.1

10 iscsiInstIndex 1.3.6.1.2.1.142.1.1.1.1.1

An arbitrary integer that uniquely identifies a particular iSCSI instance. This index value must not be modified or reused by an agent unless a reboot has occurred. Agents should attempt to keep this value persistent across reboots.This value is not accesible.


53-1001156-01

1113

10 iscsiInstDescr 1.3.6.1.2.1.142.1.1.1.1.2

iscsiInstDescr 1.3.6.1.2.1.142.1.1.1.1.2

A UTF-8 string to describe the iSCSI instance. Only a single instance is supported so the value will be 0. When used with mulitple iSCSI instances, it may be used in an implementation dependent manner to describe the purpose of the an instance.


53-1001156-01


10 iscsiInstVersionMin 1.3.6.1.2.1.142.1.1.1.1.3

The minimum version number of the iSCSI specification supported by this iSCSI instance.

This value is hard coded to 0 in this release.


53-1001156-01

1115

10 iscsiInstVersionMax 1.3.6.1.2.1.142.1.1.1.1.4


The maximum version number of the iSCSI specification supported by this iSCSI instance.

This value is hard coded to 0 in this implementation.


53-1001156-01


10 iscsiInstVendorID 1.3.6.1.2.1.142.1.1.1.1.5

A UTF-8 string describing the manufacturer of the implemention of this instance.

Not supported.


53-1001156-01

1117

10 iscsiInstVendorVersion 1.3.6.1.2.1.142.1.1.1.1.6


A UTF-8 string set by the manufacturer describing the version of the implementation of this instance. The format of this string is determined by the manufacturer. It is for information purposes, and is not related to the iSCSI specification version numbers.

It is the same as that of the fabos version.


53-1001156-01


10 iscsiInstPortalNumber 1.3.6.1.2.1.142.1.1.1.1.7

The number of rows in the iscsiPortalAttributesTable that are currently associated with this iSCSI instance.it is hardcoded to 0.


53-1001156-01

1119

10 iscsiInstNodeNumber 1.3.6.1.2.1.142.1.1.1.1.8


The number of rows in the iscsiNodeAttributesTable that are currently associated with this iSCSI instance.


53-1001156-01


10 iscsiInstSessionNumber 1.3.6.1.2.1.142.1.1.1.1.9

The number of rows in the iscsiSessionAttributesTable that are currently associated with this iSCSI instance.


53-1001156-01

1121

10 iscsiInstSsnFailures 1.3.6.1.2.1.142.1.1.1.1.10


The number of times a session belonging to this instance has failed. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiDiscontinuityTime.

Not supported.


53-1001156-01


10 iscsiInstLastSsnFailureType 1.3.6.1.2.1.142.1.1.1.1.11

Reason for failure taken from the iscsiInstSsnErrorStatsTable. A value of 0.0 is used if the reason is not found in the table.

Not supported.


53-1001156-01

1123

10 iscsiInstLastSsnRmtNodeName 1.3.6.1.2.1.142.1.1.1.1.12


The iSCSI name of the remote node from the failed session.

Not supported.


53-1001156-01


10 iscsiInstDiscontinuityTime 1.3.6.1.2.1.142.1.1.1.1.13

The value of SysUpTime at the most recent occurence of a discontinuity in one or more counters used by this instance.

Not supported.

iscsiNodeAttributesTable

This table is a list of iSCSI nodes per each iSCSI instance present on the local system.


53-1001156-01

1125

10 iscsiNodesAttributesEntry iscsiNodesAttributesEntry

An isciNodesAttributesEntry comprises the following attributes.

•

iscsiNodeIndex 1.3.6.1.2.1.142.1.1.5.1.1.1

•

iscsiNodeName 1.3.6.1.2.1.142.1.1.5.1.1.2

•

iscsiNodeAlias 1.3.6.1.2.1.142.1.1.5.1.1.3

•

iscsiNodeRoles 1.3.6.1.2.1.142.1.1.5.1.1.4

•


•


•


•


•


•


•


•


•


•


•


•


•


•



53-1001156-01

iscsiNodeIndex 1.3.6.1.2.1.142.1.1.5.1.1.1

10 iscsiNodeIndex 1.3.6.1.2.1.142.1.1.5.1.1.1

An arbitrary integer that uniquely identifies a particular node within an iSCSI instance. This is not accesible. This index value must not be modified or reused by an agent unless a reboot has occurred. Agents should attempt to keep this value persistent across reboots.


53-1001156-01

1127

10 iscsiNodeName 1.3.6.1.2.1.142.1.1.5.1.1.2

iscsiNodeName 1.3.6.1.2.1.142.1.1.5.1.1.2

This node’s iSCSI name. This name is independent of the location of the node, and can be resolved into a set of addresses through various discovery services.


53-1001156-01

iscsiNodeAlias 1.3.6.1.2.1.142.1.1.5.1.1.3

10 iscsiNodeAlias 1.3.6.1.2.1.142.1.1.5.1.1.3

A character string that is a human-readable name or description of the iSCSI node. If configured, this alias may be communicated to the initiator ot target node at the remote end of the connection during a log in request or response.

Not supported.


53-1001156-01

1129

10 iscsiNodeRoles 1.3.6.1.2.1.142.1.1.5.1.1.4

iscsiNodeRoles 1.3.6.1.2.1.142.1.1.5.1.1.4

A node can operate in a target role, initiator role, or both. It is hard coded to the value target role.


53-1001156-01


10 iscsiNodeTransportType 1.3.6.1.2.1.142.1.1.5.1.1.5

A pointer to the corresponding row in the appropriate table for this SCSI transport. This pointer is used by management stations to locatethe SCSI-level device represented by this iSCSI node.

Not supported.


53-1001156-01

1131

10 iscsiNodeInitialR2T 1.3.6.1.2.1.142.1.1.5.1.1.6


An object that indicates the InitialR2T preference for this node. When implemented, true=YES, false=will try to negotiate NO, but will accept YES.

Not supported.


53-1001156-01


10 iscsiNodeImmediateData 1.3.6.1.2.1.142.1.1.5.1.1.7

An object that indicates the ImmediateData preference for this node. When implemented, true=YES, but will accept NO, false=NO.

Not supported.


53-1001156-01

1133

10 iscsiNodeMaxOutstandingR2T 1.3.6.1.2.1.142.1.1.5.1.1.8


The maximum number of outstanding requests to transmit (R2Ts) allowed per iSCSI task.

Not supported.


53-1001156-01


10 iscsiNodeFirstBurstLength 1.3.6.1.2.1.142.1.1.5.1.1.9

The maximum length in bytes supported for unsolicited data to/from this node.

Not supported.


53-1001156-01

1135

10 iscsiNodeMaxBurstLength 1.3.6.1.2.1.142.1.1.5.1.1.10


The maximum number of bytes that can be sent within a single sequence of data-in or data-out

PDUs.

Not supported.


53-1001156-01


10 iscsiNodeMaxConnections 1.3.6.1.2.1.142.1.1.5.1.1.11

The maximum number of connections allowed in each session to and/or from this node.

Supported. Hard coded to 2.


53-1001156-01

1137

10 iscsiNodeDataSequenceInOrder 1.3.6.1.2.1.142.1.1.5.1.1.12


The preference for the order of transfer for iSCSI data PDU sequences. False (NO) indicates that

PDU sequences may be transferred in any order. True (YES) indicates that data PDU sequences must be transferred using continuously increasing offsets, except during error recovery.

Not supported.


53-1001156-01


10 iscsiNodeDataPDUInOrder 1.3.6.1.2.1.142.1.1.5.1.1.13

The preference for the order of iSCSI data PDUs within iSCSI data PDU sequences. False (NO) indicates that data PDUs may be transferred in any order within a sequence. True (YES) indicates that data PDUs must be transferred using continuously increasing addresses within a sequence, with no gaps or overlay between PDUs.

Not supported.


53-1001156-01

1139

10 iscsiNodeDefaultTime2Wait 1.3.6.1.2.1.142.1.1.5.1.1.14


The minimum time, in seconds, to wait before attempting an explicit/implicit logout or active iSCSI task reassignment after an unexpected connection termination or a connection reset.

Not supported.


53-1001156-01


10 iscsiNodeDefaultTime2Retain 1.3.6.1.2.1.142.1.1.5.1.1.15

The minimum time, in seconds, to wait, after an initial wait (Time2Wait), for a possible active iSCSI task reassignment after an unexpected connection termination or a connection reset.

Not supported.


53-1001156-01

1141

10 iscsiNodeErrorRecoveryLevel 1.3.6.1.2.1.142.1.1.5.1.1.16


The Error Recovery Level preference of this node.

Not supported.


53-1001156-01


10 iscsiNodeDiscontinuityTime 1.3.6.1.2.1.142.1.1.5.1.1.17

The value of SysUpTime at the most recent occurence of a discontinuity in one or more counters used by this node.

Not supported.


53-1001156-01

1143

10 iscsiNodeStorageType 1.3.6.1.2.1.142.1.1.5.1.1.18


The storage type for all read-write objects within this row. Rows in this table are are always created by an external process, and may have a storage type od readOnly or permanent.

The value of this variable is readOnly for this release.


53-1001156-01

iscsiSessionAttributesTable

10

iscsiSessionAttributesTable

The isciSessionAttributesTable contains a set of rows that list the sessions known to exist locally for each node in the iSCSI instance. This table contains session negotiable parameters, the target name, the initiator name, the tsid, and the isid.


53-1001156-01

1145

10 iscsiSessionsAttributesEntry iscsiSessionsAttributesEntry

An iscsiSessionsAttributesEntry comprises the following attributes.

•


•

iscsiSsnIndex 1.3.6.1.2.1.142.1.1.10.1.1.2

•


•


•


•

iscsiSsnTSIH 1.3.6.1.2.1.142.1.1.10.1.1.6

•

iscsiSsnISID 1.3.6.1.2.1.142.1.1.10.1.1.7

•


•


•


•


•

iscsiSsnType 1.3.6.1.2.1.142.1.1.10.1.1.12

•


•


•


•


•


•


•


•


•



53-1001156-01


10 iscsiSsnNodeIndex 1.3.6.1.2.1.142.1.1.10.1.1.1

An arbitrary integer that uniquely identifies a particular node within an iSCSI instance present on the local system. This value is not accesible.For normal, non-discovery sessions, this value will mapto the isciNodeIndex. For discovery sessions that do not have a node associated, the value 0

(zero) is used.


53-1001156-01

1147

10 iscsiSsnIndex 1.3.6.1.2.1.142.1.1.10.1.1.2

iscsiSsnIndex 1.3.6.1.2.1.142.1.1.10.1.1.2

An arbitrary integer that uniquely identifies a particular node within an iSCSI instance present on the local system. This value is not accesible.This index value must not be modified or reused by an agent unless a reboot has occurred. Agents should attempt to keep this value persistent across reboots.


53-1001156-01


10 iscsiSsnDirection 1.3.6.1.2.1.142.1.1.10.1.1.3

Indicates the direction of the iSCSI session.

• inboundSession - The session is established from an external initiator to a target within the iSCSI instance.

• outboundSession - The session is established from an intitiator within this iSCSI instance to an external target.

For this release, the value of iSCSISsnDirection is always inboundSession.


53-1001156-01

1149

10 iscsiSsnInitiatorName 1.3.6.1.2.1.142.1.1.10.1.1.4


If iscsiSsnDirection is Inbound, this object is a UTF-8 string that contains the name of the remote initiator. If this session is a discovery session that does not specify a particular initiator, this object contains a zero-length string. If iscsiSsnDirection is Outbound, this object contains a zero-length string.


53-1001156-01


10 iscsiSsnTargetName 1.3.6.1.2.1.142.1.1.10.1.1.5

If iscsiSsnDirection is Outbound, this object is a UTF-8 string that contains the name of the remote target. If this session is a discovery session that does not specify a particular target, this object contains a zero-length string. If scsiSsnDirection is Inbound, this object contains a zero-length string.


53-1001156-01

1151

10 iscsiSsnTSIH 1.3.6.1.2.1.142.1.1.10.1.1.6

iscsiSsnTSIH 1.3.6.1.2.1.142.1.1.10.1.1.6

The target-defined handle for this session.


53-1001156-01

iscsiSsnISID 1.3.6.1.2.1.142.1.1.10.1.1.7

10 iscsiSsnISID 1.3.6.1.2.1.142.1.1.10.1.1.7

The initiator-defined portion of the iSCSI session ID.


53-1001156-01

1153

10 iscsiSsnInitiatorAlias 1.3.6.1.2.1.142.1.1.10.1.1.8


A UTF-8 string that gives the alias communicated by the initiator end of the session during the log in phase. If no alias exists, the value is a zero-length string.


53-1001156-01


10 iscsiSsnTargetAlias 1.3.6.1.2.1.142.1.1.10.1.1.9

A UTF-8 string that gives the alias communicated by the target end of the session during the log in phase If no alias exists, the value is a zero-length string.


53-1001156-01

1155

10 iscsiSsnInitialR2T 1.3.6.1.2.1.142.1.1.10.1.1.10


If set to true, indicates that the initiator must wait for an R2T before sending to the target. If set to false, the initiator may send data immediately, within limits set by iscsiSsnFirstBurstLength and the expected data transfer length of the request.


53-1001156-01


10 iscsiSsnImmediateData 1.3.6.1.2.1.142.1.1.10.1.1.11

Indicates whether the initiator and target have agreed to support immediate data on this session.


53-1001156-01

1157

10 iscsiSsnType 1.3.6.1.2.1.142.1.1.10.1.1.12

iscsiSsnType 1.3.6.1.2.1.142.1.1.10.1.1.12

Type of iSCSI session:

• normalSession - session is a normal ISCSI session.

• discoverySession - session is being used only for discovery.


53-1001156-01


10 iscsiSsnMaxOutstandingR2T 1.3.6.1.2.1.142.1.1.10.1.1.13

The maximum number of outstanding requests-to-transmit (R2Ts) per iSCSI task within this session.


53-1001156-01

1159

10 iscsiSsnFirstBurstLength 1.3.6.1.2.1.142.1.1.10.1.1.14


The maximum length supported for unsolicited data sent within this session.


53-1001156-01


10 iscsiSsnMaxBurstLength 1.3.6.1.2.1.142.1.1.10.1.1.15

The maximum number of bytes that can be sent within a single sequence of Data-In or Data-Out

PDUs.


53-1001156-01

1161

10 iscsiSsnConnectionNumber 1.3.6.1.2.1.142.1.1.10.1.1.16


The number of transport protocol connections that currently belong to this session.


53-1001156-01


10 iscsiSsnAuthIdentity 1.3.6.1.2.1.142.1.1.10.1.1.17

This object contains a pointer to a row in the IPS-AUTH MIB module that identifies the authentication method being used on this session, as communicated during the log in phase. The value is set to null since there is no IPS-AUTH MIB


53-1001156-01

1163

10 iscsiSsnDataSequenceInOrder 1.3.6.1.2.1.142.1.1.10.1.1.18


False indicates that iSCSI data PDU sequences may be transferred in any order. True indicates that data PDU sequences must be transferred using continuously increasing offsets, except during error recovery.The default value for this is True.


53-1001156-01


10 iscsiSsnDataPDUInOrder 1.3.6.1.2.1.142.1.1.10.1.1.19

False indicates that iSCSI data PDUs within sequences may be in any order. True Indicates that data PDUs within sequences must be at continuously increasing addresses, with no gaps or overlay between PDUs. Default is true.


53-1001156-01

1165

10 iscsiSsnErrorRecoveryLevel 1.3.6.1.2.1.142.1.1.10.1.1.20


The level of error recovery negotiated between the initiator and the target. Higher numbers represent more detailed recovery schemes.


53-1001156-01


10 iscsiSsnErrorDiscontinuityTime 1.3.6.1.2.1.142.1.1.10.1.1.21

The value of SysUpTime on the most recent occasion at which any one or more of this session's counters suffered a discontinuity. When a session is established, and this object is created, it is initialized to the current value of SysUpTime.

Not supported.


53-1001156-01

1167

10 iscsiSessionStatsTable

iscsiSessionStatsTable

The isciSessionStatsTable contains performance statistics based on iSCI data bytes and PDUs.


53-1001156-01

iscsiSessionsStatsEntry

An iscsiSessionsStatsEntry comprises the following attributes.

•


•


•


•


•


•


iscsiSessionsStatsEntry

10


53-1001156-01

1169

10 iscsiSsnCmdPDUs 1.3.6.1.2.1.142.1.1.10.2.1.1


The count of command PDUs transferred on this session. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiSsnDiscontinuityTime.


53-1001156-01


10 iscsiSsnRspPDUs 1.3.6.1.2.1.142.1.1.10.2.1.2

The count of response PDUs transferred on this session. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiSsnDiscontinuityTime.


53-1001156-01

1171

10 iscsiTxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.3


The count of data octets that were transmitted by the local iSCSI node on this session. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiSsnDiscontinuityTime.This is accessible only in SNMPv3 context


53-1001156-01


10 iscsiRxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.4

The count of data octets that were received by the local iSCSI node on this session. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiSsnDiscontinuityTime. This is accessible only in SNMPv3 context


53-1001156-01

1173

10 iscsiLCTxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.5


A Low Capacity shadow object of iscsiSsnTxDataOctets for those systems that don't support

Counter64. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiSsnDiscontinuityTime.

Not supported.


53-1001156-01


10 iscsiLCRxDataOctets 1.3.6.1.2.1.142.1.1.10.2.1.6

A Low Capacity shadow object of iscsiSsnRxDataOctets for those systems that don't support

Counter64. If this counter has suffered a discontinuity, the time of the last discontinuity is indicated in iscsiSsnDiscontinuityTime.

Not supported.


53-1001156-01

1175

10 iscsiConnectionAttributesTable

iscsiConnectionAttributesTable

The isciConnectionAttributesTable contains a list of active connections within each session.


53-1001156-01

iscsiConnectionAttributesEntry

10 iscsiConnectionAttributesEntry

An iscsiConnectionAttributesEntry comprises the following attributes.

•

iscsiCxnIndex 1.3.6.1.2.1.142.1.1.11.1.1.1

•

iscsiCxnCid 1.3.6.1.2.1.142.1.1.11.1.1.2

•

iscsiCxnState 1.3.6.1.2.1.142.1.1.11.1.1.3

•


•


•


•


•


•


•


•


•


•


•


•


•



53-1001156-01

1177

10 iscsiCxnIndex 1.3.6.1.2.1.142.1.1.11.1.1.1

iscsiCxnIndex 1.3.6.1.2.1.142.1.1.11.1.1.1

An arbitrary integer that uniquely identifies a particular node within an iSCSI instance present on the local system. This value is not accesible. This index value must not be modified or reused by an agent unless a reboot has occurred. Agents should attempt to keep this value persistent across reboots.


53-1001156-01

iscsiCxnCid 1.3.6.1.2.1.142.1.1.11.1.1.2

The ISCSI connection ID for this connection.

iscsiCxnCid 1.3.6.1.2.1.142.1.1.11.1.1.2

10


53-1001156-01

1179

10 iscsiCxnState 1.3.6.1.2.1.142.1.1.11.1.1.3

iscsiCxnState 1.3.6.1.2.1.142.1.1.11.1.1.3

The current state of this connection, from an iSCSI negotiation point of view. Here are the states.

• login - The transport protocol connection has been established, but a valid iSCSI login response with the final bit set has not been sent or received.

•

full - A valid iSCSI login response with the final bit set has been sent or received.

• logout - A valid iSCSI logout command has been sent or received, but the transport protocol connection has not yet been closed.

iscsiCxnState is hard coded to value "full"


53-1001156-01


10 iscsiCxnAddrType 1.3.6.1.2.1.142.1.1.11.1.1.4

The type of Internet Network Addresses contained in the corresponding instances of iscsiCxnLocalAddr and iscsiCxnRemoteAddr. The value 'dns' is not allowed.iscsiCxnAddrType is hard coded to the value ipv4.


53-1001156-01

1181

10 iscsiCxnLocalAddr 1.3.6.1.2.1.142.1.1.11.1.1.5


The local Internet Network Address, of the type specified by iscsiCxnAddrType, used by this connection.


53-1001156-01


10 iscsiCxnProtocol 1.3.6.1.2.1.142.1.1.11.1.1.6

The transport protocol over which this connection is running. This is hard coded to tcp (6).


53-1001156-01

1183

10 iscsiCxnLocalPort 1.3.6.1.2.1.142.1.1.11.1.1.7


The local transport protocol port used by this connection. This object cannot have the value zero, since it represents an established connection.This is hard coded to 3260


53-1001156-01


10 iscsiCxnRemoteAddr 1.3.6.1.2.1.142.1.1.11.1.1.8

The remote Internet Network Address, of the type specified by iscsiCxnAddrType, used by this connection.

Only IPv4 addresses are supported.


53-1001156-01

1185

10 iscsiCxnRemotePort 1.3.6.1.2.1.142.1.1.11.1.1.9


The remote transport protocol port used by this connection. This object cannot have the value zero, since it represents an established connection.


53-1001156-01


10 iscsiCxnMaxRecvDataSegLength 1.3.6.1.2.1.142.1.1.11.1.1.10

The maximum data payload size supported for command or data PDUs able to be received on this connection.


53-1001156-01

1187

10 iscsiCxnMaxXmitDataSegLength 1.3.6.1.2.1.142.1.1.11.1.1.11


The maximum data payload size supported for command or data PDUs able to be sent on this connection.The value is min(iscsiCxnMaxRecvDataSegLength , iscsiSsnMaxBurstLength)


53-1001156-01


10 iscsiCxnHeaderIntegrity 1.3.6.1.2.1.142.1.1.11.1.1.12

This object identifies the iSCSI header digest scheme in use within this connection.


53-1001156-01

1189

10 iscsiCxnDataIntegrity 1.3.6.1.2.1.142.1.1.11.1.1.13


This object identifies the iSCSI data digest scheme in use within this connection.


53-1001156-01


10 iscsiCxnRecvMarker 1.3.6.1.2.1.142.1.1.11.1.1.14

This object identifies whether or not this connection is receiving markers in its incoming data stream.

Hard coded to false.


53-1001156-01

1191

10 iscsiCxnSendMarker 1.3.6.1.2.1.142.1.1.11.1.1.15


This object identifies whether or not this connection is inserting markers in its outgoing data stream.

Hardcoded to false.


53-1001156-01


10 iscsiCxnVersionActive 1.3.6.1.2.1.142.1.1.11.1.1.16

Active version number of the SCSI specification negotiated on this connection.

Hardcoded to 0.


53-1001156-01

1193

10 iscsiCxnVersionActive 1.3.6.1.2.1.142.1.1.11.1.1.16


53-1001156-01

MIB Object Groupings

Appendix

A

This appendix provides a function-based listing of MIB objects. To refer to the correlation of various switch objects to MIB objects, including the following.

•

Switch Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195

•

Sensor Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195

•

Port Variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195

•

Event Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196

•

ISL and End Device Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196

•

SNMP Configuration Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196

Switch Variables

MIB variables that assist in monitoring or modifying the status of switches are in the following tables or groups.

•

connUnitTable 1.3.6.1.3.94.1.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 884

•

connUnitRevsTable 1.3.6.1.3.94.1.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914

•

FIBRE-CHANNEL-FE-MIB Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221

•

FCFABRIC-ELEMENT-MIB Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341

•

Flash Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541

Sensor Variables

MIB variables that assist in monitoring or modifying the status/state of fans, power supply, and temperature are in the following tables or groups.

•

connUnitSensorTable 1.3.6.1.3.94.1.8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 920

•

swNumSensors 1.3.6.1.4.1.1588.2.1.1.1.1.21. . . . . . . . . . . . . . . . . . . . . . 551

Port Variables

MIB variables that assist in monitoring or modifying ports are in the following tables or groups.

Variables for State and Status

•

ConnSet Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881

•

fcFxPortTable 1.3.6.1.2.1.75.1.1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239

•

Fx_Port Configuration Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361


53-1001156-01

1195

A

Event Variables

•

fcFxPortStatusTable 1.3.6.1.2.1.75.1.2.1 . . . . . . . . . . . . . . . . . . . . . . . . . . 255

•

Fx_Port Physical Level Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261

•

fcFxPortCapTable 1.3.6.1.2.1.75.1.5.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325

•

Fibre Channel Port Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598

Variables for Statistics and Measurement

•

Statistics Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982

•

fcFxPortErrorTable 1.3.6.1.2.1.75.1.3.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

•

fcFxPortC2AccountingTable 1.3.6.1.2.1.75.1.4.2 . . . . . . . . . . . . . . . . . . . . 309

•

fcFeCapability Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324

Event Variables

MIB variables that assist in monitoring or modifying events are in the following tables or groups.

•

connUnitEventTable 1.3.6.1.3.94.1.11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956

•

Event Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656

ISL and End Device Variables

MIB variables that assist in monitoring or modifying ISL and end-devices are in the following tables or groups.

ISL Variables

•

connUnitLinkTable 1.3.6.1.3.94.1.12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967

•

swFabric Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568

End Device Variables

•

connUnitLinkTable 1.3.6.1.3.94.1.12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967

•

fcFxloginTable 1.3.6.1.2.1.75.1.2.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269

•

swFCPortName 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36 . . . . . . . . . . . . . . . . . . 635

SNMP Configuration Variables

MIB variables that assist in configuring SNMP are in the following tables or groups.

•

trapRegTable 1.3.6.1.3.94.2.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1055

•

SW Agent Configuration Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593


53-1001156-01

iSCSI Instance Information Variables

A

iSCSI Instance Information Variables

MIB variables that assist in gathering information about iSCSI instances are in the following tables.

•

iscsiInstanceAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1111

•

iscsiNodeAttributesTable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125

•

iscsiSessionStatsTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1168


53-1001156-01

1197

A iSCSI Instance Information Variables


53-1001156-01

MIB OIDs and Their Matching Object Names

Appendix

B

This appendix provides a listing of the MIB object names and the corresponding MIB Object ID (OID) associated with each.

MIB OIDs

iso org dod internet directory mgmt mib-2 fcFeMIB fcFeMIBObjects fcFeConfig fcFeFabricName fcFeElementName fcFeModuleCapacity fcFeModuleTable fcFeModuleEntry fcFeModuleIndex fcFeModuleDescr fcFeModuleObjectID fcFeModuleOperStatus fcFeModuleLastChange fcFeModuleFxPortCapacity fcFeModuleName fcFxPortTable fcFxPortEntry

The following matrix allows you to identify a MIB object name according to its related OID.

TABLE 24

MIB Object Name/OID Matrix

MIB Object Name OID

1

1.3

1.3.6

1.3.6.1

1.3.6.1.1

1.3.6.1.2

1.3.6.1.2.1

1.3.6.1.2.1.75

1.3.6.1.2.1.75.1

1.3.6.1.2.1.75.1.1

1.3.6.1.2.1.75.1.1.1

1.3.6.1.2.1.75.1.1.2

1.3.6.1.2.1.75.1.1.3

1.3.6.1.2.1.75.1.1.4

1.3.6.1.2.1.75.1.1.4.1

1.3.6.1.2.1.75.1.1.4.1.1

1.3.6.1.2.1.75.1.1.4.1.2

1.3.6.1.2.1.75.1.1.4.1.3

1.3.6.1.2.1.75.1.1.4.1.4

1.3.6.1.2.1.75.1.1.4.1.5

1.3.6.1.2.1.75.1.1.4.1.6

1.3.6.1.2.1.75.1.1.4.1.7

1.3.6.1.2.1.75.1.1.5

1.3.6.1.2.1.75.1.1.5.1

Page No.

page 230

page 231

page 232

page 233

page 234

page 235

page 236

page 237

page 238

page 239

page 240

page 221 page 221 page 221 page 221 page 221 page 221 page 221 page 221 page 221 page 221 page 221

page 228

page 229


53-1001156-01

1199

B

MIB OIDs

1200

TABLE 24

MIB Object Name/OID Matrix (Continued)

MIB Object Name OID fcFxPortIndex fcFxPortName fcFxPortFcphVersionHigh fcFxPortFcphVersionLow fcFxPortBbCredit fcFxPortRxBufSize fcFxPortRatov fcFxPortEdtov fcFxPortCosSupported fcFxPortIntermixSupported fcFxPortStackedConnMode fcFxPortClass2SeqDeliv fcFxPortClass3SeqDeliv fcFxPortHoldTime fcFeStatus fcFxPortStatusTable fcFxPortStatusEntry fcFxPortID fcFxPortBbCreditAvailable fcFxPortOperMode fcFxPortAdminMode fcFxPortPhysTable fcFxPortPhysEntry fcFxPortPhysAdminStatus fcFxPortPhysOperStatus fcFxPortPhysLastChange fcFxPortPhysRttov fcFxLoginTable fcFxLoginEntry fcFxPortNxLoginIndex fcFxPortFcphVersionAgreed fcFxPortNxPortBbCredit fcFxPortNxPortRxDataFieldSize fcFxPortCosSuppAgreed fcFxPortIntermixSuppAgreed fcFxPortStackedConnModeAgreed

1.3.6.1.2.1.75.1.1.5.1.1

1.3.6.1.2.1.75.1.1.5.1.2

1.3.6.1.2.1.75.1.1.5.1.3

1.3.6.1.2.1.75.1.1.5.1.4

1.3.6.1.2.1.75.1.1.5.1.5

1.3.6.1.2.1.75.1.1.5.1.6

1.3.6.1.2.1.75.1.1.5.1.7

1.3.6.1.2.1.75.1.1.5.1.8

1.3.6.1.2.1.75.1.1.5.1.9

1.3.6.1.2.1.75.1.1.5.1.10

1.3.6.1.2.1.75.1.1.5.1.11

.3.6.1.2.1.75.1.1.5.1.12

1.3.6.1.2.1.75.1.1.5.1.13

1.3.6.1.2.1.75.1.1.5.1.14

1.3.6.1.2.1.75.1.2

1.3.6.1.2.1.75.1.2.1

1.3.6.1.2.1.75.1.2.1.1

1.3.6.1.2.1.75.1.2.1.1.1

1.3.6.1.2.1.75.1.2.1.1.2

1.3.6.1.2.1.75.1.2.1.1.3

1.3.6.1.2.1.75.1.2.1.1.4

1.3.6.1.2.1.75.1.2.2

1.3.6.1.2.1.75.1.2.2.1

1.3.6.1.2.1.75.1.2.2.1.1

1.3.6.1.2.1.75.1.2.2.1.2

1.3.6.1.2.1.75.1.2.2.1.3

1.3.6.1.2.1.75.1.2.2.1.4

1.3.6.1.2.1.75.1.2.3

1.3.6.1.2.1.75.1.2.3.1

1.3.6.1.2.1.75.1.2.3.1.1

1.3.6.1.2.1.75.1.2.3.1.2

1.3.6.1.2.1.75.1.2.3.1.3

1.3.6.1.2.1.75.1.2.3.1.4

1.3.6.1.2.1.75.1.2.3.1.5

1.3.6.1.2.1.75.1.2.3.1.6

1.3.6.1.2.1.75.1.2.3.1.7

Page No.

page 262

page 263

page 264

page 265

page 266

page 267

page 269

page 270

page 254

page 221

page 255

page 256

page 257

page 258

page 259

page 260

page 241

page 242

page 243

page 244

page 245

page 246

page 247

page 248

page 249

page 250

page 251

page 252

page 253

page 271

page 272

page 273

page 274

page 275

page 276

page 277


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID fcFxPortClass2SeqDelivAgreed fcFxPortClass3SeqDelivAgreed fcFxPortNxPortName fcFxPortConnectedNxPort fcFxPortBbCreditModel fcFeError fcFxPortErrorTable fcFxPortErrorEntry fcFxPortLinkFailures fcFxPortSyncLosses fcFxPortSigLosses fcFxPortPrimSeqProtoErrors fcFxPortInvalidTxWords fcFxPortInvalidCrcs fcFxPortDelimiterErrors fcFxPortAddressIdErrors fcFxPortLinkResetIns fcFxPortLinkResetOuts fcFxPortOlsIns fcFxPortOlsOuts fcFeAccounting fcFxPortC1AccountingTable fcFxPortC1AccountingEntry fcFxPortC1InFrames fcFxPortC1OutFrames fcFxPortC1InOctets fcFxPortC1OutOctets fcFxPortC1Discards fcFxPortC1FbsyFrames fcFxPortC1FrjtFrames fcFxPortC1InConnections fcFxPortC1OutConnections fcFxPortC1ConnTime fcFxPortC2AccountingTable fcFxPortC2AccountingEntry fcFxPortC2InFrames

1.3.6.1.2.1.75.1.2.3.1.8

1.3.6.1.2.1.75.1.2.3.1.9

1.3.6.1.2.1.75.1.2.3.1.10

1.3.6.1.2.1.75.1.2.3.1.11

1.3.6.1.2.1.75.1.2.3.1.12

1.3.6.1.2.1.75.1.3

1.3.6.1.2.1.75.1.3.1

1.3.6.1.2.1.75.1.3.1.1

1.3.6.1.2.1.75.1.3.1.1.1

1.3.6.1.2.1.75.1.3.1.1.2

1.3.6.1.2.1.75.1.3.1.1.3

1.3.6.1.2.1.75.1.3.1.1.4

1.3.6.1.2.1.75.1.3.1.1.5

1.3.6.1.2.1.75.1.3.1.1.6

1.3.6.1.2.1.75.1.3.1.1.7

1.3.6.1.2.1.75.1.3.1.1.8

1.3.6.1.2.1.75.1.3.1.1.9

1.3.6.1.2.1.75.1.3.1.1.10

1.3.6.1.2.1.75.1.3.1.1.11

1.3.6.1.2.1.75.1.3.1.1.12

1.3.6.1.2.1.75.1.4

1.3.6.1.2.1.75.1.4.1

1.3.6.1.2.1.75.1.4.1.1

1.3.6.1.2.1.75.1.4.1.1.1

1.3.6.1.2.1.75.1.4.1.1.2

1.3.6.1.2.1.75.1.4.1.1.3

1.3.6.1.2.1.75.1.4.1.1.4

1.3.6.1.2.1.75.1.4.1.1.5

1.3.6.1.2.1.75.1.4.1.1.6

1.3.6.1.2.1.75.1.4.1.1.7

1.3.6.1.2.1.75.1.4.1.1.8

1.3.6.1.2.1.75.1.4.1.1.9

1.3.6.1.2.1.75.1.4.1.1.10

1.3.6.1.2.1.75.1.4.2

1.3.6.1.2.1.75.1.4.2.1

1.3.6.1.2.1.75.1.4.2.1.1

MIB OIDs

B

Page No.

page 298 page 298

page 299

page 300

page 301

page 302

page 303

page 304

page 290

page 291

page 292

page 293

page 294

page 295

page 296

page 221

page 278

page 279

page 280

page 281

page 282 page 282

page 283

page 284

page 285

page 286

page 287

page 288

page 289

page 305

page 306

page 307

page 308

page 309

page 310

page 311

1201

B

MIB OIDs

TABLE 24


MIB Object Name OID fcFxPortC2OutFrames fcFxPortC2InOctets fcFxPortC2OutOctets fcFxPortC2Discards fcFxPortC2FbsyFrames fcFxPortC2FrjtFrames fcFxPortC3AccountingTable fcFxPortC3AccountingEntry fcFxPortC3InFrames fcFxPortC3OutFrames fcFxPortC3InOctets fcFxPortC3OutOctets fcFxPortC3Discards fcFeCapabilities fcFxPortCapTable fcFxPortCapEntry fcFxPortCapFcphVersionHigh fcFxPortCapFcphVersionLow fcFxPortCapBbCreditMax fcFxPortCapBbCreditMin fcFxPortCapRxDataFieldSizeMax fcFxPortCapRxDataFieldSizeMin fcFxPortCapCos fcFxPortCapIntermix fcFxPortCapStackedConnMode fcFxPortCapClass2SeqDeliv fcFxPortCapClass3SeqDeliv fcFxPortCapHoldTimeMax fcFxPortCapHoldTimeMin fcFeMIBConformance fcFeMIBCompliances fcFeMIBMinimumCompliance fcFeMIBFullCompliance fcFeMIBGroups fcFeConfigGroup fcFeStatusGroup

1.3.6.1.2.1.75.1.4.2.1.2

1.3.6.1.2.1.75.1.4.2.1.3

1.3.6.1.2.1.75.1.4.2.1.4

1.3.6.1.2.1.75.1.4.2.1.5

1.3.6.1.2.1.75.1.4.2.1.6

1.3.6.1.2.1.75.1.4.2.1.7

1.3.6.1.2.1.75.1.4.3

1.3.6.1.2.1.75.1.4.3.1

1.3.6.1.2.1.75.1.4.3.1.1

1.3.6.1.2.1.75.1.4.3.1.2

1.3.6.1.2.1.75.1.4.3.1.3

1.3.6.1.2.1.75.1.4.3.1.4

1.3.6.1.2.1.75.1.4.3.1.5

1.3.6.1.2.1.75.1.5

1.3.6.1.2.1.75.1.5.1

1.3.6.1.2.1.75.1.5.1.1

1.3.6.1.2.1.75.1.5.1.1.1

1.3.6.1.2.1.75.1.5.1.1.2

1.3.6.1.2.1.75.1.5.1.1.3

1.3.6.1.2.1.75.1.5.1.1.4

1.3.6.1.2.1.75.1.5.1.1.5

1.3.6.1.2.1.75.1.5.1.1.6

1.3.6.1.2.1.75.1.5.1.1.7

1.3.6.1.2.1.75.1.5.1.1.8

1.3.6.1.2.1.75.1.5.1.1.9

1.3.6.1.2.1.75.1.5.1.1.10

1.3.6.1.2.1.75.1.5.1.1.11

1.3.6.1.2.1.75.1.5.1.1.12

1.3.6.1.2.1.75.1.5.1.1.13

1.3.6.1.2.1.75.2

1.3.6.1.2.1.75.2.1

1.3.6.1.2.1.75.2.1.1

1.3.6.1.2.1.75.2.1.2

1.3.6.1.2.1.75.2.2

1.3.6.1.2.1.75.2.2.1

1.3.6.1.2.1.75.2.2.2


53-1001156-01

Page No.

page 332

page 333

page 334

page 335

page 336

page 337

page 338

page 339

page 221 page 221 page 221

page 325

page 326

page 327

page 328

page 329

page 330

page 331

page 312

page 313

page 314

page 315

page 316

page 317

page 318

page 319

page 320

page 321

page 322

page 323

page 324

page 221


53-1001156-01

TABLE 24


MIB Object Name OID fcFeErrorGroup fcFeClass1AccountingGroup fcFeClass2AccountingGroup fcFeClass3AccountingGroup fcFeCapabilitiesGroup

1.3.6.1.2.1.75.2.2.3

1.3.6.1.2.1.75.2.2.4

1.3.6.1.2.1.75.2.2.5

1.3.6.1.2.1.75.2.2.6

1.3.6.1.2.1.75.2.2.7

experimental 1.3.6.1.3

fibreChannel 1.3.6.1.3.42

fcFabric fcFe

1.3.6.1.3.42.2

1.3.6.1.3.42.2.1

fcFeConfig fcFabricName fcElementName fcFeModuleCapacity

1.3.6.1.3.42.2.1.1

1.3.6.1.3.42.2.1.1.1

1.3.6.1.3.42.2.1.1.2

1.3.6.1.3.42.2.1.1.3

fcFeModuleTable fcFeModuleEntry fcFeModuleIndex fcFeModuleDescr fcFeModuleObjectID fcFeModuleOperStatus fcFeModuleLastChange fcFeModuleFxPortCapacity fcFeModuleName fcFxConfTable fcFxConfEntry fcFxConfModuleIndex fcFxConfFxPortIndex fcFxPortName fcFxPortFcphVersionHigh fcFxPortFcphVersionLow fcFxPortBbCredit fcFxPortRxBufSize fcFxPortRatov fcFxPortEdtov fcFxPortCosSupported fcFxPortIntermixSupported fcFxPortStackedConnMode

1.3.6.1.3.42.2.1.1.4

1.3.6.1.3.42.2.1.1.4.1

1.3.6.1.3.42.2.1.1.4.1.1

1.3.6.1.3.42.2.1.1.4.1.2

1.3.6.1.3.42.2.1.1.4.1.3

1.3.6.1.3.42.2.1.1.4.1.4

1.3.6.1.3.42.2.1.1.4.1.5

1.3.6.1.3.42.2.1.1.4.1.6

1.3.6.1.3.42.2.1.1.4.1.7

1.3.6.1.3.42.2.1.1.5

1.3.6.1.3.42.2.1.1.5.1

1.3.6.1.3.42.2.1.1.5.1.1

1.3.6.1.3.42.2.1.1.5.1.2

1.3.6.1.3.42.2.1.1.5.1.3

1.3.6.1.3.42.2.1.1.5.1.4

1.3.6.1.3.42.2.1.1.5.1.5

1.3.6.1.3.42.2.1.1.5.1.6

1.3.6.1.3.42.2.1.1.5.1.7

1.3.6.1.3.42.2.1.1.5.1.8

1.3.6.1.3.42.2.1.1.5.1.9

1.3.6.1.3.42.2.1.1.5.1.10

1.3.6.1.3.42.2.1.1.5.1.11

1.3.6.1.3.42.2.1.1.5.1.12

MIB OIDs

B

Page No.

page 360

page 362

page 363

page 364

page 365

page 366

page 367

page 368

page 369

page 370

page 371

page 372

page 373

page 374

page 375

page 352

page 353

page 354

page 355

page 356

page 357

page 358

page 359

page 341 page 341 page 341 page 341 page 341

page 348

page 349

page 350

1203

B

MIB OIDs

1204

TABLE 24


MIB Object Name OID fcFxPortClass2SeqDeliv fcFxPortClass3SeqDeliv fcFxPortHoldTime fcFxPortBaudRate fcFxPortMedium fcFxPortTxType fcFxPortDistance fcFeOp fcFxPortOperTable fcFxPortOperEntry fcFxPortOperModuleIndex fcFxPortOperFxPortIndex fcFxPortID fcFxPortAttachedPortName fcFxPortConnectedPort fcFxPortBbCreditAvailable fcFxPortOperMode fcFxPortAdminMode fcFxPortPhysTable fcFxPortPhysEntry fcFxPortPhysModuleIndex fcFxPortPhysFxPortIndex fcFxPortPhysAdminStatus fcFxPortPhysOperStatus fcFxPortPhysLastChange fcFxPortPhysRttov fcFxlogiTable fcFxlogiEntry fcFxlogiModuleIndex fcFxlogiFxPortIndex fcFxlogiNxPortIndex fcFxPortFcphVersionAgreed fcFxPortNxPortBbCredit fcFxPortNxPortRxDataFieldSize fcFxPortCosSuppAgreed fcFxPortIntermixSuppAgreed

1.3.6.1.3.42.2.1.1.5.1.13

1.3.6.1.3.42.2.1.1.5.1.14

1.3.6.1.3.42.2.1.1.5.1.15

1.3.6.1.3.42.2.1.1.5.1.16

1.3.6.1.3.42.2.1.1.5.1.17

1.3.6.1.3.42.2.1.1.5.1.18

1.3.6.1.3.42.2.1.1.5.1.19

1.3.6.1.3.42.2.1.2

1.3.6.1.3.42.2.1.2.1

1.3.6.1.3.42.2.1.2.1.1

1.3.6.1.3.42.2.1.2.1.1.1

1.3.6.1.3.42.2.1.2.1.1.2

1.3.6.1.3.42.2.1.2.1.1.3

1.3.6.1.3.42.2.1.2.1.1.4

1.3.6.1.3.42.2.1.2.1.1.5

1.3.6.1.3.42.2.1.2.1.1.6

1.3.6.1.3.42.2.1.2.1.1.7

1.3.6.1.3.42.2.1.2.1.1.8

1.3.6.1.3.42.2.1.2.3

1.3.6.1.3.42.2.1.2.3.1

1.3.6.1.3.42.2.1.2.3.1.1

1.3.6.1.3.42.2.1.2.3.1.2

1.3.6.1.3.42.2.1.2.3.1.3

1.3.6.1.3.42.2.1.2.3.1.4

1.3.6.1.3.42.2.1.2.3.1.5

1.3.6.1.3.42.2.1.2.3.1.6

1.3.6.1.3.42.2.1.2.4

1.3.6.1.3.42.2.1.2.4.1

1.3.6.1.3.42.2.1.2.4.1.1

1.3.6.1.3.42.2.1.2.4.1.2

1.3.6.1.3.42.2.1.2.4.1.3

1.3.6.1.3.42.2.1.2.4.1.4

1.3.6.1.3.42.2.1.2.4.1.5

1.3.6.1.3.42.2.1.2.4.1.6

1.3.6.1.3.42.2.1.2.4.1.7

1.3.6.1.3.42.2.1.2.4.1.8

Page No.

page 396

page 397

page 398

page 399

page 400

page 402

page 403

page 404

page 388

page 389

page 390

page 391

page 392

page 393

page 394

page 395

page 376

page 377

page 378

page 379

page 380

page 381

page 382

page 341

page 383

page 384

page 385

page 386

page 387

page 405

page 406

page 407

page 408

page 409

page 410

page 411


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID fcFxPortStackedConnModeAgreed fcFxPortClass2SeqDelivAgreed fcFxPortClass3SeqDelivAgreed fcFxPortNxPortName fcFxPortConnectedNxPort fcFxPortBbCreditModel fcFeError fcFxPortErrorTable fcFxPortErrorEntry fcFxPortErrorModuleIndex fcFxPortErrorFxPortIndex fcFxPortLinkFailures fcFxPortSyncLosses fcFxPortSigLosses fcFxPortPrimSeqProtoErrors fcFxPortInvalidTxWords fcFxPortInvalidCrcs fcFxPortDelimiterErrors fcFxPortAddressIdErrors fcFxPortLinkResetIns fcFxPortLinkResetOuts fcFxPortOlsIns fcFxPortOlsOuts fcFeAcct fcFeCap fcFxPortCapTable fcFxPortCapEntry fcFxPortCapModuleIndex fcFxPortCapFxPortIndex fcFxPortCapFcphVersionHigh fcFxPortCapFcphVersionLow fcFxPortCapBbCreditMax fcFxPortCapBbCreditMin fcFxPortCapRxDataFieldSizeMax fcFxPortCapRxDataFieldSizeMin fcFxPortCapCos

1.3.6.1.3.42.2.1.2.4.1.9

1.3.6.1.3.42.2.1.2.4.1.10

1.3.6.1.3.42.2.1.2.4.1.11

1.3.6.1.3.42.2.1.2.4.1.12

1.3.6.1.3.42.2.1.2.4.1.13

1.3.6.1.3.42.2.1.2.4.1.14

1.3.6.1.3.42.2.1.3

1.3.6.1.3.42.2.1.3.1

1.3.6.1.3.42.2.1.3.1.1

1.3.6.1.3.42.2.1.3.1.1.1

1.3.6.1.3.42.2.1.3.1.1.2

1.3.6.1.3.42.2.1.3.1.1.3

1.3.6.1.3.42.2.1.3.1.1.4

1.3.6.1.3.42.2.1.3.1.1.5

1.3.6.1.3.42.2.1.3.1.1.6

1.3.6.1.3.42.2.1.3.1.1.7

1.3.6.1.3.42.2.1.3.1.1.8

1.3.6.1.3.42.2.1.3.1.1.9

1.3.6.1.3.42.2.1.3.1.1.10

1.3.6.1.3.42.2.1.3.1.1.11

1.3.6.1.3.42.2.1.3.1.1.12

1.3.6.1.3.42.2.1.3.1.1.13

1.3.6.1.3.42.2.1.3.1.1.14

1.3.6.1.3.42.2.1.4

1.3.6.1.3.42.2.1.5

1.3.6.1.3.42.2.1.5.1

1.3.6.1.3.42.2.1.5.1.1

1.3.6.1.3.42.2.1.5.1.1.1

1.3.6.1.3.42.2.1.5.1.1.2

1.3.6.1.3.42.2.1.5.1.1.3

1.3.6.1.3.42.2.1.5.1.1.4

1.3.6.1.3.42.2.1.5.1.1.5

1.3.6.1.3.42.2.1.5.1.1.6

1.3.6.1.3.42.2.1.5.1.1.7

1.3.6.1.3.42.2.1.5.1.1.8

1.3.6.1.3.42.2.1.5.1.1.9

MIB OIDs

B

Page No.

page 432

page 433

page 341 page 341

page 434

page 435

page 436

page 437

page 424

page 425

page 426

page 427

page 428

page 429

page 430

page 431

page 412

page 413

page 414

page 415

page 416

page 417

page 341

page 418

page 419

page 420

page 421

page 422

page 423

page 438

page 439

page 440

page 441

page 442

page 443

page 444

1205

B

MIB OIDs

1206

TABLE 24


MIB Object Name OID fcFxPortCapIntermix fcFxPortCapStackedConnMode fcFxPortCapClass2SeqDeliv fcFxPortCapClass3SeqDeliv fcFxPortCapHoldTimeMax fcFxPortCapHoldTimeMin fcFxPortCapBaudRates fcFxPortCapMedia fcmgmt connSet uNumber systemURL connUnitTable connUnitEntry connUnitId connUnitGlobalId connUnitType connUnitNumports connUnitState connUnitStatus connUnitProduct connUnitSn connUnitUpTime connUnitUrl connUnitDomainId connUnitProxyMaster connUnitPrincipal connUnitNumSensors connUnitStatusChangeTime connUnitConfigurationChangeTime connUnitNumRevs connUnitNumZones connUnitModuleId connUnitName connUnitInfo connUnitControl

1.3.6.1.3.42.2.1.5.1.1.10

1.3.6.1.3.42.2.1.5.1.1.11

1.3.6.1.3.42.2.1.5.1.1.12

1.3.6.1.3.42.2.1.5.1.1.13

1.3.6.1.3.42.2.1.5.1.1.14

1.3.6.1.3.42.2.1.5.1.1.15

1.3.6.1.3.42.2.1.5.1.1.16

1.3.6.1.3.42.2.1.5.1.1.17

1.3.6.1.3.94

1.3.6.1.3.94.1

1.3.6.1.3.94.1.1

1.3.6.1.3.94.1.2

1.3.6.1.3.94.1.6

1.3.6.1.3.94.1.6.1

1.3.6.1.3.94.1.6.1.1

1.3.6.1.3.94.1.6.1.2

1.3.6.1.3.94.1.6.1.3

1.3.6.1.3.94.1.6.1.4

1.3.6.1.3.94.1.6.1.5

1.3.6.1.3.94.1.6.1.6

1.3.6.1.3.94.1.6.1.7

1.3.6.1.3.94.1.6.1.8

1.3.6.1.3.94.1.6.1.9

1.3.6.1.3.94.1.6.1.10

1.3.6.1.3.94.1.6.1.11

1.3.6.1.3.94.1.6.1.12

1.3.6.1.3.94.1.6.1.13

1.3.6.1.3.94.1.6.1.14

1.3.6.1.3.94.1.6.1.15

1.3.6.1.3.94.1.6.1.16

1.3.6.1.3.94.1.6.1.17

1.3.6.1.3.94.1.6.1.18

1.3.6.1.3.94.1.6.1.19

1.3.6.1.3.94.1.6.1.20

1.3.6.1.3.94.1.6.1.21

1.3.6.1.3.94.1.6.1.22

Page No.

page 893

page 894

page 895

page 896

page 897

page 898

page 899

page 900

page 885

page 886

page 887

page 888

page 889

page 890

page 891

page 892

page 445

page 446

page 447

page 448

page 449

page 450

page 451

page 452

page 874 page 874

page 882

page 883

page 884

page 901

page 902

page 903

page 904

page 905

page 906

page 907


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID connUnitContact connUnitLocation connUnitEventFilter connUnitNumEvents connUnitMaxEvents connUnitEventCurrID connUnitRevsTable connUnitRevsEntry connUnitRevsUnitId connUnitRevsIndex connUnitRevsRevId connUnitRevsDescription connUnitSensorTable connUnitSensorEntry connUnitSensorUnitId connUnitSensorIndex connUnitSensorName connUnitSensorStatus connUnitSensorInfo connUnitSensorMessage connUnitSensorType connUnitSensorCharacteristic connUnitPortTable connUnitPortEntry connUnitPortUnitId connUnitPortIndex connUnitPortType connUnitPortFCClassCap connUnitPortFCClassOp connUnitPortState connUnitPortStatus connUnitPortTransmitterType connUnitPortModuleType connUnitPortWwn connUnitPortFCId connUnitPortSn

1.3.6.1.3.94.1.6.1.23

1.3.6.1.3.94.1.6.1.24

1.3.6.1.3.94.1.6.1.25

1.3.6.1.3.94.1.6.1.26

1.3.6.1.3.94.1.6.1.27

1.3.6.1.3.94.1.6.1.28

1.3.6.1.3.94.1.7

1.3.6.1.3.94.1.7.1

1.3.6.1.3.94.1.7.1.1

1.3.6.1.3.94.1.7.1.2

1.3.6.1.3.94.1.7.1.3

1.3.6.1.3.94.1.7.1.4

1.3.6.1.3.94.1.8

1.3.6.1.3.94.1.8.1

1.3.6.1.3.94.1.8.1.1

1.3.6.1.3.94.1.8.1.2

1.3.6.1.3.94.1.8.1.3

1.3.6.1.3.94.1.8.1.4

1.3.6.1.3.94.1.8.1.5

1.3.6.1.3.94.1.8.1.6

1.3.6.1.3.94.1.8.1.7

1.3.6.1.3.94.1.8.1.8

1.3.6.1.3.94.1.10

1.3.6.1.3.94.1.10.1

1.3.6.1.3.94.1.10.1.1

1.3.6.1.3.94.1.10.1.2

1.3.6.1.3.94.1.10.1.3

1.3.6.1.3.94.1.10.1.4

1.3.6.1.3.94.1.10.1.5

1.3.6.1.3.94.1.10.1.6

1.3.6.1.3.94.1.10.1.7

1.3.6.1.3.94.1.10.1.8

1.3.6.1.3.94.1.10.1.9

1.3.6.1.3.94.1.10.1.10

1.3.6.1.3.94.1.10.1.11

1.3.6.1.3.94.1.10.1.12

MIB OIDs

B

Page No.

page 929

page 930

page 931

page 932

page 933

page 934

page 935

page 936

page 921

page 922

page 923

page 924

page 925

page 926

page 927

page 928

page 908

page 909

page 910

page 911

page 912

page 913

page 914

page 915

page 916

page 917

page 918

page 919

page 920

page 937

page 938

page 939

page 940

page 941

page 942

page 943

1207

B

MIB OIDs

1208

TABLE 24


MIB Object Name OID connUnitPortRevision connUnitPortVendor connUnitPortSpeed connUnitPortControl connUnitPortName connUnitPortPhysicalNumber connUnitPortStatObject connUnitPortProtocolCap connUnitPortProtocolOp connUnitPortNodeWwn connUnitPortHWState connUnitEventTable connUnitEventEntry connUnitEventUnitId connUnitEventIndex connUnitEventId connUnitREventTime connUnitSEventTime connUnitEventSeverity connUnitEventType connUnitEventObject connUnitEventDescr connUnitLinkTable connUnitLinkEntry connUnitLinkUnitId connUnitLinkIndex connUnitLinkNodeIdX connUnitLinkPortNumberX connUnitLinkPortWwnX connUnitLinkNodeIdY connUnitLinkPortNumberY connUnitLinkPortWwnY connUnitLinkAgentAddressY connUnitLinkAgentAddressTypeY connUnitLinkAgentPortY connUnitLinkUnitTypeY

1.3.6.1.3.94.1.10.1.13

1.3.6.1.3.94.1.10.1.14

1.3.6.1.3.94.1.10.1.15

1.3.6.1.3.94.1.10.1.16

1.3.6.1.3.94.1.10.1.17

1.3.6.1.3.94.1.10.1.18

1.3.6.1.3.94.1.10.1.19

1.3.6.1.3.94.1.10.1.20

1.3.6.1.3.94.1.10.1.21

1.3.6.1.3.94.1.10.1.22

1.3.6.1.3.94.1.10.1.23

1.3.6.1.3.94.1.11

1.3.6.1.3.94.1.11.1

1.3.6.1.3.94.1.11.1.1

1.3.6.1.3.94.1.11.1.2

1.3.6.1.3.94.1.11.1.3

1.3.6.1.3.94.1.11.1.4

1.3.6.1.3.94.1.11.1.5

1.3.6.1.3.94.1.11.1.6

1.3.6.1.3.94.1.11.1.7

1.3.6.1.3.94.1.11.1.8

1.3.6.1.3.94.1.11.1.9

1.3.6.1.3.94.1.12

1.3.6.1.3.94.1.12.1

1.3.6.1.3.94.1.12.1.1

1.3.6.1.3.94.1.12.1.2

1.3.6.1.3.94.1.12.1.3

1.3.6.1.3.94.1.12.1.4

1.3.6.1.3.94.1.12.1.5

1.3.6.1.3.94.1.12.1.6

1.3.6.1.3.94.1.12.1.7

1.3.6.1.3.94.1.12.1.8

1.3.6.1.3.94.1.12.1.9

1.3.6.1.3.94.1.12.1.10

1.3.6.1.3.94.1.12.1.11

1.3.6.1.3.94.1.12.1.12

Page No.

page 966

page 967

page 968

page 969

page 970

page 971

page 972

page 973

page 958

page 959

page 960

page 961

page 962

page 963

page 964

page 965

page 944

page 945

page 946

page 947

page 949

page 950

page 951

page 952

page 953

page 954

page 955

page 956

page 957

page 974

page 975

page 976

page 977

page 978

page 979

page 980


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID connUnitLinkConnIdY connUnitLinkCurrIndex trapReg trapMaxClients trapClientCount trapRegTable trapRegEntry trapRegIpAddress trapRegPort trapRegFilter trapRegRowState revisionNumber statSet connUnitPortStatTable connUnitPortStatEntry connUnitPortStatUnitId connUnitPortStatIndex connUnitPortStatCountError connUnitPortStatCountTxObjects connUnitPortStatCountRxObjects connUnitPortStatCountTxElements connUnitPortStatCountRxElements connUnitPortStatCountBBCreditZero connUnitPortStatCountInputBuffersFull connUnitPortStatCountFBSYFrames connUnitPortStatCountPBSYFrames connUnitPortStatCountFRJTFrames connUnitPortStatCountPRJTFrames connUnitPortStatCountClass1RxFrames connUnitPortStatCountClass1TxFrames connUnitPortStatCountClass1FBSYFrames connUnitPortStatCountClass1PBSYFrames connUnitPortStatCountClass1FRJTFrames connUnitPortStatCountClass1PRJTFrames connUnitPortStatCountClass2RxFrames connUnitPortStatCountClass2TxFrames

1.3.6.1.3.94.1.12.1.13

1.3.6.1.3.94.1.12.1.14

1.3.6.1.3.94.2

1.3.6.1.3.94.2.1

1.3.6.1.3.94.2.2

1.3.6.1.3.94.2.3

1.3.6.1.3.94.2.3.1

1.3.6.1.3.94.2.3.1.1

1.3.6.1.3.94.2.3.1.2

1.3.6.1.3.94.2.3.1.3

1.3.6.1.3.94.2.3.1.4

1.3.6.1.3.94.3

1.3.6.1.3.94.4

1.3.6.1.3.94.4.5

1.3.6.1.3.94.4.5.1

1.3.6.1.3.94.4.5.1.1

1.3.6.1.3.94.4.5.1.2

1.3.6.1.3.94.4.5.1.3

1.3.6.1.3.94.4.5.1.4

1.3.6.1.3.94.4.5.1.5

1.3.6.1.3.94.4.5.1.6

1.3.6.1.3.94.4.5.1.7

1.3.6.1.3.94.4.5.1.8

1.3.6.1.3.94.4.5.1.9

1.3.6.1.3.94.4.5.1.10

1.3.6.1.3.94.4.5.1.11

1.3.6.1.3.94.4.5.1.12

1.3.6.1.3.94.4.5.1.13

1.3.6.1.3.94.4.5.1.14

1.3.6.1.3.94.4.5.1.15

1.3.6.1.3.94.4.5.1.16

1.3.6.1.3.94.4.5.1.17

1.3.6.1.3.94.4.5.1.18

1.3.6.1.3.94.4.5.1.19

1.3.6.1.3.94.4.5.1.20

1.3.6.1.3.94.4.5.1.21

MIB OIDs

B

Page No.

page 991

page 992

page 993

page 994

page 995

page 996

page 997

page 998

page 983

page 984

page 985

page 986

page 987

page 988

page 989

page 990

page 981

page 982

page 1055

page 1053

page 1054

page 1055

page 1056

page 1057

page 1058

page 1059

page 1060

page 1061

page 982

page 999

page 1000

page 1001

page 1002

page 1003

page 1004

page 1005

1209

B

MIB OIDs

1210

TABLE 24


MIB Object Name OID connUnitPortStatCountClass2FBSYFrames connUnitPortStatCountClass2PBSYFrames connUnitPortStatCountClass2FRJTFrames connUnitPortStatCountClass2PRJTFrames connUnitPortStatCountClass3RxFrames connUnitPortStatCountClass3TxFrames connUnitPortStatCountClass3Discards connUnitPortStatCountRxMulticastObjects connUnitPortStatCountTxMulticastObjects connUnitPortStatCountRxBroadcastObjects connUnitPortStatCountTxBroadcastObjects connUnitPortStatCountRxLinkResets connUnitPortStatCountTxLinkResets connUnitPortStatCountNumberLinkResets connUnitPortStatCountRxOfflineSequences connUnitPortStatCountTxOfflineSequences connUnitPortStatCountNumberOffline

Sequences connUnitPortStatCountLinkFailures connUnitPortStatCountInvalidCRC connUnitPortStatCountInvalidTxWords connUnitPortStatCountPrimitiveSequence

ProtocolErrors connUnitPortStatCountLossofSignal connUnitPortStatCountLossofSynchronization connUnitPortStatCountInvalidOrderedSets connUnitPortStatCountFramesTooLong connUnitPortStatCountFramesTruncated connUnitPortStatCountAddressErrors connUnitPortStatCountDelimiterErrors connUnitPortStatCountEncodingDisparityErrors connUnitServiceSet connUnitServiceScalars connUnitSnsMaxEntry connUnitServiceTables connUnitSnsTable connUnitSnsEntry

1.3.6.1.3.94.4.5.1.22

1.3.6.1.3.94.4.5.1.23

1.3.6.1.3.94.4.5.1.24

1.3.6.1.3.94.4.5.1.25

1.3.6.1.3.94.4.5.1.26

1.3.6.1.3.94.4.5.1.27

1.3.6.1.3.94.4.5.1.28

1.3.6.1.3.94.4.5.1.29

1.3.6.1.3.94.4.5.1.30

1.3.6.1.3.94.4.5.1.31

1.3.6.1.3.94.4.5.1.32

1.3.6.1.3.94.4.5.1.33

1.3.6.1.3.94.4.5.1.34

1.3.6.1.3.94.4.5.1.35

1.3.6.1.3.94.4.5.1.36

1.3.6.1.3.94.4.5.1.37

1.3.6.1.3.94.4.5.1.38

1.3.6.1.3.94.4.5.1.39

1.3.6.1.3.94.4.5.1.40

1.3.6.1.3.94.4.5.1.41

1.3.6.1.3.94.4.5.1.42

1.3.6.1.3.94.4.5.1.43

1.3.6.1.3.94.4.5.1.44

1.3.6.1.3.94.4.5.1.45

1.3.6.1.3.94.4.5.1.46

1.3.6.1.3.94.4.5.1.47

1.3.6.1.3.94.4.5.1.48

1.3.6.1.3.94.4.5.1.49

1.3.6.1.3.94.4.5.1.50

1.3.6.1.3.94.5

1.3.6.1.3.94.5.1

1.3.6.1.3.94.5.1.1

1.3.6.1.3.94.5.2

1.3.6.1.3.94.5.2.1

1.3.6.1.3.94.5.2.1.1

page 1023

page 1024

page 1025

page 1026

page 1027

page 1028

page 1029

page 1030

page 1031

page 1032

page 1033

page 1034 page 1034

page 1035 page 1035

page 1036 page 1036

page 1037

Page No.

page 1006

page 1007

page 1008

page 1009

page 1010

page 1011

page 1012

page 1013

page 1014

page 1015

page 1016

page 1017

page 1018

page 1019

page 1020

page 1021

page 1022


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID connUnitSnsId connUnitSnsPortIndex connUnitSnsPortIdentifier connUnitSnsPortName connUnitSnsNodeName connUnitSnsClassOfSvc connUnitSnsNodeIPAddress connUnitSnsProcAssoc connUnitSnsFC4Type connUnitSnsPortType connUnitSnsPortIPAddress connUnitSnsFabricPortName connUnitSnsHardAddress connUnitSnsSymbolicPortName connUnitSnsSymbolicNodeName private enterprises bcsi commDev fibrechannel fcSwitch sw swSystem swCurrentDate swBootDate swFWLastUpdated swFlashLastUpdated swBootPromLastUpdated swFirmwareVersion swOperStatus swAdmStatus swTelnetShellAdmStatus swSsn swFlashDLOperStatus swFlashDLAdmStatus swFlashDLHost

1.3.6.1.3.94.5.2.1.1.1

1.3.6.1.3.94.5.2.1.1.2

1.3.6.1.3.94.5.2.1.1.3

1.3.6.1.3.94.5.2.1.1.4

1.3.6.1.3.94.5.2.1.1.5

1.3.6.1.3.94.5.2.1.1.6

1.3.6.1.3.94.5.2.1.1.7

1.3.6.1.3.94.5.2.1.1.8

1.3.6.1.3.94.5.2.1.1.9

1.3.6.1.3.94.5.2.1.1.10

1.3.6.1.3.94.5.2.1.1.11

1.3.6.1.3.94.5.2.1.1.12

1.3.6.1.3.94.5.2.1.1.13

1.3.6.1.3.94.5.2.1.1.14

1.3.6.1.3.94.5.2.1.1.15

1.3.6.1.4

1.3.6.1.4.1

1.3.6.1.4.1.1588

1.3.6.1.4.1.1588.2

1.3.6.1.4.1.1588.2.1

1.3.6.1.4.1.1588.2.1.1

1.3.6.1.4.1.1588.2.1.1.1

1.3.6.1.4.1.1588.2.1.1.1.1

1.3.6.1.4.1.1588.2.1.1.1.1.1

1.3.6.1.4.1.1588.2.1.1.1.1.2

1.3.6.1.4.1.1588.2.1.1.1.1.3

1.3.6.1.4.1.1588.2.1.1.1.1.4

1.3.6.1.4.1.1588.2.1.1.1.1.5

1.3.6.1.4.1.1588.2.1.1.1.1.6

1.3.6.1.4.1.1588.2.1.1.1.1.7

1.3.6.1.4.1.1588.2.1.1.1.1.8

1.3.6.1.4.1.1588.2.1.1.1.1.9

1.3.6.1.4.1.1588.2.1.1.1.1.10

1.3.6.1.4.1.1588.2.1.1.1.1.11

1.3.6.1.4.1.1588.2.1.1.1.1.12

1.3.6.1.4.1.1588.2.1.1.1.1.13

MIB OIDs

B

Page No.

page 511

page 532 page 532

page 533

page 534

page 535

page 536

page 537

page 1051

page 1052

page 511 page 511 page 511 page 511 page 511 page 511

page 1038

page 1039

page 1040

page 1041

page 1042

page 1043

page 1044

page 1045

page 1046

page 1047

page 1048

page 1049

page 1050

page 538

page 539

page 540

page 541

page 542

page 543

page 544

1211

B

MIB OIDs

1212

TABLE 24


MIB Object Name OID swFlashDLUser swFlashDLFile swFlashDLPassword swBeaconOperStatus swBeaconAdmStatus swDiagResult swNumSensors swSensorTable swSensorEntry swSensorIndex swSensorType swSensorStatus swSensorValue swSensorInfo swTrackChangesInfo swFabric swDomainID swPrincipalSwitch swNumNbs swVfId swNbTable swNbEntry swNbIndex swNbMyPort swNbRemDomain swNbRemPort swNbBaudRate swNbIslState swNbIslCost swNbRemPortName swModule swAgtCfg swAgtCmtyTable swAgtCmtyEntry swAgtCmtyIdx swAgtCmtyStr

1.3.6.1.4.1.1588.2.1.1.1.1.14

1.3.6.1.4.1.1588.2.1.1.1.1.15

1.3.6.1.4.1.1588.2.1.1.1.1.16

1.3.6.1.4.1.1588.2.1.1.1.1.18

1.3.6.1.4.1.1588.2.1.1.1.1.19

1.3.6.1.4.1.1588.2.1.1.1.1.20

1.3.6.1.4.1.1588.2.1.1.1.1.21

1.3.6.1.4.1.1588.2.1.1.1.1.22

1.3.6.1.4.1.1588.2.1.1.1.1.22.1

1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1

1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2

1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3

1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4

1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5

1.3.6.1.4.1.1588.2.1.1.1.1.23

1.3.6.1.4.1.1588.2.1.1.1.2

1.3.6.1.4.1.1588.2.1.1.1.2.1

1.3.6.1.4.1.1588.2.1.1.1.2.2

1.3.6.1.4.1.1588.2.1.1.1.2.8

1.3.6.1.4.1.1588.2.1.1.1.2.9

1.3.6.1.4.1.1588.2.1.1.1.2.10

1.3.6.1.4.1.1588.2.1.1.1.2.10.1

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.1

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.2

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.3

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.4

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.5

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.6

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.7

1.3.6.1.4.1.1588.2.1.1.1.2.10.1.8

1.3.6.1.4.1.1588.2.1.1.1.3

1.3.6.1.4.1.1588.2.1.1.1.4

1.3.6.1.4.1.1588.2.1.1.1.4.11

1.3.6.1.4.1.1588.2.1.1.1.4.11.1

1.3.6.1.4.1.1588.2.1.1.1.4.11.1.1

1.3.6.1.4.1.1588.2.1.1.1.4.11.1.2

Page No.

page 573

page 574

page 575

page 576

page 577

page 578

page 579

page 580

page 558

page 559

page 568 page 568

page 569

page 570

page 571

page 572

page 545

page 546

page 547

page 548

page 549

page 550

page 551

page 552

page 553

page 554

page 555

page 556

page 557

page 581


page 594

page 595

page 596


53-1001156-01


53-1001156-01

MIB OIDs

B

TABLE 24


MIB Object Name OID swAgtTrapRcp swFCport swFCPortCapacity swFCPortTable swFCPortEntry swFCPortIndex swFCPortType swFCPortPhyState swFCPortOpStatus swFCPortAdmStatus swFCPortLinkState swFCPortTxType swFCPortTxWords swFCPortRxWords swFCPortTxFrames swFCPortRxFrames swFCPortRxC2Frames swFCPortRxC3Frames swFCPortRxLCs swFCPortRxMcasts swFCPortTooManyRdys swFCPortNoTxCredits swFCPortRxEncInFrs swFCPortRxCrcs swFCPortRxTruncs swFCPortRxTooLongs swFCPortRxBadEofs swFCPortRxEncOutFrs swFCPortRxBadOs swFCPortC3Discards swFCPortMcastTimedOuts swFCPortTxMcasts swFCPortLipIns swFCPortLipOuts swFCPortLipLastAlpa swFCPortWwn

1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3

1.3.6.1.4.1.1588.2.1.1.1.6

1.3.6.1.4.1.1588.2.1.1.1.6.1

1.3.6.1.4.1.1588.2.1.1.1.6.2

1.3.6.1.4.1.1588.2.1.1.1.6.2.1

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34

Page No.

page 619

page 620

page 621

page 622

page 623

page 624

page 625

page 626

page 611

page 612

page 613

page 614

page 615

page 616

page 617

page 618

page 597

page 598

page 599

page 601

page 602

page 603

page 604

page 605

page 606

page 607

page 608

page 609

page 610

page 627

page 628

page 629

page 630

page 631

page 632

page 633

1213

B

MIB OIDs

1214

TABLE 24


MIB Object Name OID swFCPortSpeed swFCPortName swFCPortSpecifier swFCPortFlag swFCPortBrcdType swNs swNsLocalNumEntry swNsLocalTable swNsLocalEntry swNsEntryIndex swNsPortID swNsPortType swNsPortName swNsPortSymb swNsNodeName swNsNodeSymb swNsIPA swNsIpAddress swNsCos swNsFc4 swNsIpNxPort swNsWwn swNsHardAddr swEvent swEventTrapLevel swEventNumEntries swEventTable swEventEntry swEventIndex swEventTimeInfo swEventLevel swEventRepeatCount swEventDescr swFwSystem swFwFabricWatchLicense swFwClassAreaTable

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39

1.3.6.1.4.1.1588.2.1.1.1.7

1.3.6.1.4.1.1588.2.1.1.1.7.1

1.3.6.1.4.1.1588.2.1.1.1.7.2

1.3.6.1.4.1.1588.2.1.1.1.7.2.1

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.3

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.4

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.5

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.6

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.7

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.8

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.9

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.11

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.12

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.13

1.3.6.1.4.1.1588.2.1.1.1.7.2.1.14

1.3.6.1.4.1.1588.2.1.1.1.8

1.3.6.1.4.1.1588.2.1.1.1.8.1

1.3.6.1.4.1.1588.2.1.1.1.8.4

1.3.6.1.4.1.1588.2.1.1.1.8.5

1.3.6.1.4.1.1588.2.1.1.1.8.5.1

1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1

1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2

1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3

1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4

1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5

1.3.6.1.4.1.1588.2.1.1.1.10

1.3.6.1.4.1.1588.2.1.1.1.10.1

1.3.6.1.4.1.1588.2.1.1.1.10.2

Page No.

page 654

page 655

page 656

page 657

page 658

page 659

page 660

page 661

page 646

page 647

page 648

page 649

page 650

page 651

page 652

page 653

page 634

page 635

page 636

page 637

page 638

page 635

page 639

page 640

page 641

page 642

page 643

page 644

page 645

page 662

page 663

page 664

page 665

page 666

page 667

page 668


53-1001156-01


53-1001156-01

MIB OIDs

B

TABLE 24


MIB Object Name OID swFwClassAreaEntry swFwClassAreaIndex swFwWriteThVals swFwDefaultUnit swFwDefaultTimebase swFwDefaultLow swFwDefaultHigh swFwDefaultBufSize swFwCustUnit swFwCustTimebase swFwCustLow swFwCustHigh swFwCustBufSize swFwThLevel swFwWriteActVals swFwDefaultChangedActs swFwDefaultExceededActs swFwDefaultBelowActs swFwDefaultAboveActs swFwDefaultInBetweenActs swFwCustChangedActs swFwCustExceededActs swFwCustBelowActs swFwCustAboveActs swFwCustInBetweenActs swFwValidActs swFwActLevel swFwThresholdTable swFwThresholdEntry swFwThresholdIndex swFwStatus swFwName swFwLabel swFwCurVal swFwLastEvent swFwLastEventVal

1.3.6.1.4.1.1588.2.1.1.1.10.2.1

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.2

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.3

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.4

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.5

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.6

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.7

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.8

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.9

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.10

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.11

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.12

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.13

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.14

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.15

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.16

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.17

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.18

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.19

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.20

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.21

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.22

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.23

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.24

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.25

1.3.6.1.4.1.1588.2.1.1.1.10.2.1.26

1.3.6.1.4.1.1588.2.1.1.1.10.3

1.3.6.1.4.1.1588.2.1.1.1.10.3.1

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.2

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.5

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7

Page No.

page 690

page 691

page 692

page 693

page 694

page 695

page 696

page 697

page 682

page 683

page 684

page 685

page 686

page 687

page 688

page 689

page 669

page 670

page 671

page 672

page 673

page 674

page 675

page 676

page 677

page 678

page 679

page 680

page 681

page 698

page 699

page 700

page 702

page 703

page 704

page 705

1215

B

MIB OIDs

1216

TABLE 24


MIB Object Name OID swFwLastEventTime swFwLastState swFwBehaviorType swFwBehaviorInt swEndDevice swEndDeviceRlsTable swEndDeviceRlsEntry swEndDevicePort swEndDeviceAlpa swEndDevicePortID swEndDeviceLinkFailure swEndDeviceSyncLoss swEndDeviceSigLoss swEndDeviceProtoErr swEndDeviceInvalidWord swEndDeviceInvalidCRC swBlmPerfMnt swBlmPerfALPAMntTable swBlmPerfALPAMntEntry swBlmPerfAlpaPort swBlmPerfAlpaIndx swBlmPerfAlpa swBlmPerfAlpaCRCCnt swBlmPerfEEMntTable swBlmPerfEEMntEntry swBlmPerfEEPort swBlmPerfEERefKey swBlmPerfEECRC swBlmPerfEEFCWRx swBlmPerfEEFCWTx swBlmPerfEESid swBlmPerfEEDid swBlmPerfFltMntTable swBlmPerfFltMntEntry swBlmPerfFltPort swBlmPerfFltRefkey

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.10

1.3.6.1.4.1.1588.2.1.1.1.10.3.1.11

1.3.6.1.4.1.1588.2.1.1.1.21

1.3.6.1.4.1.1588.2.1.1.1.21.1

1.3.6.1.4.1.1588.2.1.1.1.21.1.1

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.1

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.2

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.3

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.4

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.5

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.6

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.7

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.8

1.3.6.1.4.1.1588.2.1.1.1.21.1.1.9

1.3.6.1.4.1.1588.2.1.1.1.23

1.3.6.1.4.1.1588.2.1.1.1.23.1

1.3.6.1.4.1.1588.2.1.1.1.23.1.1

1.3.6.1.4.1.1588.2.1.1.1.23.1.1.1

1.3.6.1.4.1.1588.2.1.1.1.23.1.1.2

1.3.6.1.4.1.1588.2.1.1.1.23.1.1.3

1.3.6.1.4.1.1588.2.1.1.1.23.1.1.4

1.3.6.1.4.1.1588.2.1.1.1.23.2

1.3.6.1.4.1.1588.2.1.1.1.23.2.1

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.1

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.2

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.3

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.4

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.5

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.6

1.3.6.1.4.1.1588.2.1.1.1.23.2.1.7

1.3.6.1.4.1.1588.2.1.1.1.23.3

1.3.6.1.4.1.1588.2.1.1.1.23.3.1

1.3.6.1.4.1.1588.2.1.1.1.23.3.1.1

1.3.6.1.4.1.1588.2.1.1.1.23.3.1.2

Page No.

page 736

page 737

page 738

page 739

page 740

page 741

page 742

page 743

page 719

page 720

page 721

page 732 page 732

page 733

page 734

page 735

page 706

page 707

page 708

page 709

page 711 page 711

page 712

page 713

page 714

page 715

page 716

page 717

page 718

page 744

page 745

page 746

page 747

page 748

page 749

page 750


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID swBlmPerfFltCnt swBlmPerfFltAlias swID swEtherIPAddress swEtherIPMask swFCIPAddress swFCIPMask swIPv6Address swIPv6Status swModel swFabricMemTable swFabricMemEntry swFabricMemWwn swFabricMemDid swFabricMemName swFabricMemEIP swFabricMemFCIP swFabricMemGWIP swFabricMemType swFabricMemShortVersion swIDIDMode swFCPortName swGroup swGroupTable swGroupEntry swGroupIndex swGroupName swGroupType swGroupMemTable swGroupMemEntry swGroupID swGroupMemWwn swGroupMemPos swTrunk swSwitchTrunkable swTrunkTable

1.3.6.1.4.1.1588.2.1.1.1.23.3.1.3

1.3.6.1.4.1.1588.2.1.1.1.23.3.1.4

1.3.6.1.1.1588.2.1.1.1.1.24

1.3.6.1.1.1588.2.1.1.1.1.25

1.3.6.1.1.1588.2.1.1.1.1.26

1.3.6.1.1.1588.2.1.1.1.1.27

1.3.6.1.1.1588.2.1.1.1.1.28

1.3.6.1.4.1.1588.2.1.1.1.1.29

1.3.6.1.4.1.1588.2.1.1.1.1.30

1.3.6.1.4.1.1588.2.1.1.1.1.31

1.3.6.1.1.1588.2.1.1.1.2.11

1.3.6.1.1.1588.2.1.1.1.2.11.1

1.3.6.1.1.1588.2.1.1.1.2.11.1.1

1.3.6.1.1.1588.2.1.1.1.2.11.1.2

1.3.6.1.1.1588.2.1.1.1.2.11.1.3

1.3.6.1.1.1588.2.1.1.1.2.11.1.4

1.3.6.1.1.1588.2.1.1.1.2.11.1.5

1.3.6.1.1.1588.2.1.1.1.2.11.1.6

1.3.6.1.1.1588.2.1.1.1.2.11.1.7

1.3.6.1.1.1588.2.1.1.1.2.11.1.8

1.3.6.1.1.1588.2.1.1.1.2.12

1.3.6.1.4.1588.2.1.1.1.6.2.1.36

1.3.6.1.4.1.1588.2.1.1.1.22

1.3.6.1.4.1.1588.2.1.1.1.22.1

1.3.6.1.4.1.1588.2.1.1.1.22.1.1

1.3.6.1.4.1.1588.2.1.1.1.22.1.1.1

1.3.6.1.4.1.1588.2.1.1.1.22.1.1.2

1.3.6.1.4.1.1588.2.1.1.1.22.1.1.3

1.3.6.1.4.1.1588.2.1.1.1.22.2

1.3.6.1.4.1.1588.2.1.1.1.22.2.1

1.3.6.1.4.1.1588.2.1.1.1.22.2.1.1

1.3.6.1.4.1.1588.2.1.1.1.22.2.1.2

1.3.6.1.4.1.1588.2.1.1.1.22.2.1.3

1.3.6.1.4.1.1588.2.1.1.1.24

1.3.6.1.4.1.1588.2.1.1.1.24.1

1.3.6.1.4.1.1588.2.1.1.1.24.2

MIB OIDs

B

Page No.

page 751

page 752

page 560

page 561

page 562

page 563

page 564

page 565

page 566

page 567

page 582

page 583

page 584

page 585

page 586

page 587

page 588

page 589

page 590

page 591

page 592

page 635

page 722

page 723

page 724

page 725

page 726

page 727

page 728

page 729

page 730

page 731

page 753 page 753

page 754

1217

B

MIB OIDs

1218

TABLE 24


MIB Object Name OID swTrunkEntry swTrunkPortIndex swTrunkGroupNumber swTrunkMaster swPortTrunked swTrunkGrpTable swTrunkGrpEntry swTrunkGrpNumber swTrunkGrpMaster swTrunkGrpTx swTrunkGrpRx sw28k sw21kN24k

1.3.6.1.4.1.1588.2.1.1.1.24.2.1

1.3.6.1.4.1.1588.2.1.1.1.24.2.1.1

1.3.6.1.4.1.1588.2.1.1.1.24.2.1.2

1.3.6.1.4.1.1588.2.1.1.1.24.2.1.3

1.3.6.1.4.1.1588.2.1.1.1.24.2.1.4

1.3.6.1.4.1.1588.2.1.1.1.24.3

1.3.6.1.4.1.1588.2.1.1.1.24.3.1

1.3.6.1.4.1.1588.2.1.1.1.24.3.1.1

1.3.6.1.4.1.1588.2.1.1.1.24.3.1.2

1.3.6.1.4.1.1588.2.1.1.1.24.3.1.3

1.3.6.1.4.1.1588.2.1.1.1.24.3.1.4

1.3.6.1.4.1.1588.2.1.1.2

1.3.6.1.4.1.1588.2.1.1.3

sw20x0 fcipEntityInstancetable fcipEntityInstanceEntry fcipEntityId fcipEntityName fcipEntityAddressType fcipEntityAddress fcipEntityTcpConn

1.3.6.1.4.1.1588.2.1.1.4

1.3.6.1.2.1.224.1.1.4

1.3.6.1.2.1.224.1.1.4.1.

1.3.6.1.2.1.224.1.1.4.1.1

1.3.6.1.2.1.224.1.1.4.1.2

1.3.6.1.2.1.224.1.1.4.1.3

1.3.6.1.2.1.224.1.1.4.1.4

1.3.6.1.2.1.224.1.1.4.1.5

fcipEntitySeqNumWrap fcipEntityPHBSupport fcipEntityStatus fcipLinkTable

1.3.6.1.2.1.224.1.1.4.1.6

1.3.6.1.2.1.224.1.1.4.1.7

1.3.6.1.2.1.224.1.1.4.1.8

1.3.6.1.2.1.224.1.1.5

fcipLinkEntry 1.3.6.1.2.1.224.1.1.5.1

fcipLinkindex 1.3.6.1.2.1.224.1.1.5.1.1

fcipLinklfindex fcipLinkCost

1.3.6.1.2.1.224.1.1.5.1.2

1.3.6.1.2.1.224.1.1.5.1.3

fcipLinkLocalFcipEntityMode fcipLinkLocalFcipEntityAddressType fcipLinkLocalFcipEntityAddress fcipLinkRemFcipEntityWnn fcipLinkRemFcipEntityId fcipLinkRemFcipEntityAddressType fcipLinkRemFcipEntityAddress

1.3.6.1.2.1.224.1.1.5.1.4

1.3.6.1.2.1.224.1.1.5.1.5

1.3.6.1.2.1.224.1.1.5.1.6

1.3.6.1.2.1.224.1.1.5.1.7

1.3.6.1.2.1.224.1.1.5.1.8

1.3.6.1.2.1.224.1.1.5.1.9

1.3.6.1.2.1.224.1.1.5.1.10

Page No.

page 512


page 1073

page 1068 page 1068 page 1068 page 1068 page 1068 page 1068 page 1068 page 1068 page 1068 page 1068 page 1068

page 755

page 756

page 757

page 758

page 759

page 760

page 761

page 762

page 763

page 764

page 765

page 512 page 512

page 1068 page 1068 page 1068 page 1068 page 1068 page 1068 page 1068


53-1001156-01


53-1001156-01

TABLE 24


MIB Object Name OID fcipLinkStatus fcipLinkCreateTime

1.3.6.1.2.1.224.1.1.5.1.11

1.3.6.1.2.1.224.1.1.5.1.12

fcipExtendedLinkEntry 1.3.6.1.4.1.1588.4.1.1

fcipExtendedLinkIfIndex fcipExtendedLinkTcpRetransmits

1.3.6.1.4.1.1588.4.1.1.1

1.3.6.1.4.1.1588.4.1.1.2

fcipExtendedLinkTcpDropped Packets fcipExtendedLinkCompressionRatio fcipExtendedLinkTcpSmoothedRTT fcipExtendedLinkRawBytes fcipExtendedLinkCompressedBytes fcipExtendedLinkConnectedCount fcipExtendedLinkRtxRtxTO fcipExtendedLinkRtxDupAck fcipExtendedLinkDupAck fcipExtendedLinkRtt fcipExtendedLinkOoo fcipExtendedLinkSlowStarts

1.3.6.1.4.1.1588.4.1.1.3

1.3.6.1.4.1.1588.4.1.1.4

1.3.6.1.4.1.1588.4.1.1.5

1.3.6.1.4.1.1588.4.1.1.6

1.3.6.1.4.1.1588.4.1.1.7

1.3.6.1.4.1.1588.4.1.1.8

1.3.6.1.4.1.1588.4.1.1.9

1.3.6.1.4.1.1588.4.1.1.10

1.3.6.1.4.1.1588.4.1.1.11

1.3.6.1.4.1.1588.4.1.1.12

1.3.6.1.4.1.1588.4.1.1.13

1.3.6.1.4.1.1588.4.1.1.14

MIB OIDs

B

Page No.

page 1068 page 1068

page 1069

page 1093

page 1094

page 1095

page 1096

page 1097

page 1098

page 1099

page 1100

page 1101

page 1102

page 1103

page 1104

page 1105

page 1106

1219

B

MIB OIDs


53-1001156-01

Index

A accounting group

,

296

,

433

address translation group

,

55

agtcfgDefault command

,

12

agtcfgSet command

,

12

agtcfgShow command

,

12

ASIC performance monitoring group

,

732

E

EGP group

,

168

end device group

,

711

Entity MIB conformance information

,

502

Entity MIB objects

,

459

Entity MIB overview

,

453

Entity MIB system organization of MIB objects

,

454

Entity MIB trap

,

501

error group

,

282

,

417

errShow command

,

4

event group

,

656

event variables

,

1196

B before loading MIBs

,

6

Brocade MIB files

,

6

C capability group

,

324

,

433

commands

,

12

agtcfgDefault

,

12

agtCfgSet

,

12

agtCfgShow

,

12

errShow

,

4

sensorShow

,

11

snmpConfig

,

4

,

12

snmpMibCapSet

,

12

snmpMibCapShow

,

12

switchStatusPolicySet

,

4

configuration group

,

226

,

347

configuring SNMP

,

12

connectivity group

,

881

,

1070

,

1079

,

1111

,

1125

,

1145

,

1168

D definitions for entity MIB

,

455

definitions for Fcfabric-Element-MIB

,

345

definitions for Fcmgmt-MIB

,

879

,

1070

,

1111

definitions for Fibre-Channel-fe-MIB

,

224

disabling MIBs

,

4

F fabric group

,

568

Fabric OS commands

,

12

fabric watch group

,

666

FCFABRIC-ELEMENT-MIB (experimental branch)

,

340

FCFABRIC-ELEMENT-MIB organization

,

341

FCIP

,

1067

,

1068

FCMGMT-MIB system organization of MIB objects

,

874

,

1068

,

1108

FE MIB overview

,

219

Fibre Channel port group

,

598

Fibrealliance MIB overview

,

873

,

1067

,

1107

Fibre-Channel-Fe-MIB (MIB-II branch)

,

219

Fibre-Channel-Fe-MIB organization

,

221

Ficon MIB overview

,

807

Ficon MIB system organization of MIB objects

,

807

ficonlirr group

,

841

ficonrlir group

,

851

ficonrnid group

,

811

flash administration

,

541

FX_Port fabric login table

,

268

,

401


53-1001156-01

1221

H ha MIB overview

,

775

ha-MIB traps

,

803

ha-MIB traps and sample triggers

,

806

high-availability group

,

777

I

ICMP group

,

110

interfaces group

,

29

interfaces table

,

31

IP group

,

61

iSCSI

,

1107

,

1108

iSCSI MIB Organization

,

1068

,

1108

iSCSI MIB Overview

,

1067

,

1107

ISL and end device variables

,

1196

L linkincidentMIBtraps group

,

867

loading brocade MIBs

,

6

M

MIB loading order

,

7

MIB oids

,

1199

MIB-II object hierarchy

,

14

MIB-II overview

,

13

N name server database group

,

639

O objects and types imported

,

21

operation group

,

382

P physical entity group

,

460

1222

port variables

,

1195

R revision number scalar

,

1061

S sensor variables

,

1195

sensorShow command

,

11

Series 3000 Variables

,

1196

,

1197

service group

,

1034

SNMP configuration variables

,

1196

SNMP group

,

168

SNMP trap registration group

,

1053

SNMP traps for ficon

,

807

snmpConfig command

,

4

,

12

snmpMibCapSet command

,

12

snmpMibCapShow command

,

12

statistics group

,

982

status group

,

254

sw agent configuration group

,

593

sw MIB overview

,

511

sw traps

,

522

switch group

,

721

switch variables

,

1195

switchStatusPolicySet command

,

4

sw-MIB system organization of MIB objects

,

511

system group

,

22

,

532

T

TCP connection table

,

150

TCP group

,

137

textual conventions

,

21

,

457

,

809

textual conventions for sw-MIB

,

519

transmission group

,

168

traps

,

4

trunking group

,

753

U

UDP group

,

160

understanding MIBs

,

3


53-1001156-01

understanding SNMP bASICs

,

2

unsupported tables

,

1061

unsupported traps

,

1062


53-1001156-01

1223


53-1001156-01

Brocade Communications Systems POWEREDGE 840 Reference Manual

Assistant Bot

Fabric OS

MIB Reference

Contents

About This Document

In this chapter

How this document is organized

Supported hardware and software

What’s new in this document

Document conventions

Text formatting

Notes, cautions, and warnings

NOTE

ATTENTION

Key terms

Notice to the reader

Additional information

Brocade resources

Other industry resources

Getting technical help

Document feedback

Understanding Brocade SNMP

In this chapter

Setting the SNMP Security Level

TABLE 1

TABLE 1

Understanding SNMP Basics

FIGURE 1

FIGURE 2

FIGURE 3

Understanding MIBs

FIGURE 4

Understanding SNMP Traps

Object Instances

Loading Brocade MIBs

Brocade MIB Files

Before Loading MIBs

TABLE 2

MIB Loading Order

NOTE

FIGURE 5

SNMP CLI usage

Brocade 7500 / FR4-18i and Brocade MIBs

Access Gateway and Brocade MIBs

TABLE 3

Firmware Upgrades and Enabled Traps

Fabric OS Commands for Configuring SNMP

TABLE 4

Support for Administrative Domains

Support for Role Based Access Control

Support for IP V6 Addressing

Support for Virtual Fabric

MIB-II (RFC1213-MIB)

MIB II Overview

FIGURE 6

FIGURE 7

FIGURE 8

FIGURE 9

FIGURE 10

FIGURE 11

FIGURE 12

FIGURE 13

FIGURE 14

FIGURE 15

FIGURE 16

TABLE 5

System Group

Interfaces Group

NOTE

NOTE

AT Group

IP Group

NOTE

NOTE

NOTE

NOTE

NOTE

ICMP Group

NOTE