Genie HDUB4P User manual

HDUB4P

4 Channel Passive HD

Video UTP Transceiver

User Manual

1. Introduction

The HDUB4P is a 4 Channel Passive HD (Non-Amplified) Video UTP Transceiver that allows transmission of real time and high performance colour or monochrome CCTV video or HD-CVI / AHD / HD-TVI / HD video over UTP cable which is ideal for multi-point surveillance.

2. Key Features

• Passive, No Need for a Power Supply

• HD-CVI, HD-TVI, AHD, CVBS 4 in 1 Compatible Design

• Real-Time Transmission, No Delay

• Strong Surge Protection, ESD and Lighting Protection

• Supports MIT Structure

• Easy Operation

3. Technical Specification

Model Number

Transmission Channel

Video Connector

Transmission Distance

Coaxial Video Connector

UTP Cable Video Connector

Compatible Video Format

Signal Transmission Width

Anti-Interference

Coaxial Video Connector Surge

UTP Cable Communication

Connector Surge Protection

ESD

HDUB4P

4 Channel

4 Channel

HD-CVI (720p): 370m, HD-CVI (1080p): 100m

HD-TVI (720p): 200m, HD-TVI (1080p): 200m

AHD-L/M (720p): 250m, AHD-L/M (960p): 250m

AHD-H (1080p): 250m, Anaglogue Video: 500m

Female BNC Connector

Female RJ45 Connector, 8 Channel Screw Push Terminal

HD-CVI, HD-TVI, AHD, CVBS

0-70MHz

>60dB

2KV (Different Mode) Per: IEC61000-4-5

2KV (Different Mode) per: IEC6100-4-5

Operation Temperature

Storage Temperature

Humidity

1a Contact Discharge Level 3

1b Air Discharge Level 3

Per: IEC6100-4-2

0 ~ 55°C

-40°C ~ 85°C

0~95%

Dimensions (L x W x H) 85 x 82 x 25 mm (Including Connector Length)

*Design and Specifications are subject to change without notice.

4. Board Diagram

Front Back

2

PoE OUT

Coaxial Port

PoE OUT

RJ45 Port

HDUB4P - 4 Channel Passive HD UTP Transciever

PoE IN

Terminal Block Port

NOTICE

• Transmission distance is related to wire quality. Please use standard UTP cable and coaxial cable.

• RJ45 connector and screw push terminal connection mode can not use at the same time. Choose only one of them.

5. Application Diagram

UTP CAT5 / CAT5e / CAT6

Coax

Monitor

DVR

6. Installation Steps

1. Turn off the power of the camera and display before installation.

2. Check if the cables and display device are occupied.

3. Connect monitor or DVR and BNC connectorof the product over coaxial cable

4. Connect the product push terminal UTP cable connector or RJ45 connector and camera output port over UTP cable.

5. Check whether installation is correct, the device is good, make sure all connection is reliable, connect power cable, system is power on.

6. Make sure network is normal.

7. Troubleshooting

Please follow below if the device doesn’t work:

• Check if its according to the manual.

• If you choose RJ-45, make sure both ends of UTP cable are both the same (568A or 568B).

• If you choose green terminal block, make sure cable of same colour be in the same pin.

• Check all connections such as BNC, RJ-45.

• Make sure the real distance doesnt exceed the allowed transmission distance.

• Make sure the cables are good quality.

• Replace the device at question by a normal working device.

• If the problem still occurs, please contact the dealer.

HDUB4P - 4 Channel Passive HD UTP Transciever 3

GENIE CCTV LTD.

CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT

Tel: +44 (0) 1707 330541 Fax: +44 (0) 1707 330543 www.geniecctv.com

Edition. GN- May 2016