Users Manual
AP699E8.1U10-4
AP Router User manual
Ver: 1.0
Contents
Chapter 1
Introduction
The AP699E8.1U10-4, a Wireless Area Network(WLAN)
Access Point
supporting 802.11 b/g/n, bringing high-speed wireless
Internet connection to a home or office, can provide the transmission of broadband data service. It is suitable for using in a wide
range of both residential (in-home) and commercial (offices, apartments, hotels, warehouses) network applications. It gives you a
blazing fast connection to the internet, far fast and more convenient. The AP699E8.1U10-4 Access Point is a high-performance
wireless gateway
and can support
downstream up to 300Mbps and upstream up to 300Mbps.
AP699E8.1U10-4 has a megabit wide area network(WAN)
port connecting external internet network. Using 802.11 b/g/n
wireless technology, Wi-Fi enabled computers and devices can wirelessly connect to the AP699E8.1U10-4 and share a single
incoming Internet connection. With four additional
local Ethernet LAN ports, you can connect four different
PCs
sharing
Internet connection.
A Web-based user interface allows you to easily modify settings to connect to your Internet Service Provider (ISP). This Web
interface also provides traffic statistics, connection speed, and other detailed information.
The AP699E8.1U10-4 supports DHCP client, DHCP server, as well as
NAT/NAPT functions. As a DHCP client,
AP699E8.1U10-4 can dynamicly acquire external internet IP address. As a DHCP client, AP699E8.1U10-4 can dynamicly alloc
local
IP addresses to the associated wireless stations and wired LAN port
address and external
IP address
PCs.
NAT/NAPT implements local
IP
conversion.
The AP699E8.1U10-4 supports static IP, Dynamic IP, as well as PPPoE connections, and works with applications such as online
gaming and VPN transparent
connections with no additional configuration.
The AP699E8.1U10-4 is easily upgradeable, making it future-proof for both end-users and service providers. Whether it’s for a
home user who wants to share wireless high-speed Internet access or for a small office that needs Internet access for conducting
essential business activities, the AP699E8.1U10-4 is the ideal wireless broadband solution.
Product Outline
4
Product topology
Applications
l Home and SOHO wireless gateway
l The small enterprise Applications
l
l
l
l
l
l
TV over IP (IPTV)
Voice over IP (VoIP)
Higher data rate broadband sharing
Shared broadband internet access
Audio and video streaming and transfer
PC file and application sharing
l Network and online gaming
Compliance Certificates
l Wi-Fi
Certification
l FCC Class B
l CE Mark
Feature
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
IEEE802.11 compatible b/g/n draft 2.0 access ponit
Antenna configurations: 2T3R Modes
Support 64/128-bit WEP, 802.1x, WPA, and WPA2 for wireless security
Support 802.11e wireless multimedia Qos
Support 802.11f inter AP handover
Support mutiple SSID
SSID hide
Support VLAN
MAC address access control list
MAC addresses self-learning
Support transparent bridging
VPN Pass Through on L2TP, PPTP, IPSec
DHCP Server and Client
Support static IP routing
Support NAT、NAPT
Support DMZ
Support IP QoS
5
l telnet, HTTP Web Management, TFTP for Firmware Upgrade
l wireless signal rates: 54, 48, 36, 24, 18, 12, 9, 6 Mb/s for 802.11g; 11, 5.5, 2, 1 Mb/s for 802.11b; 11n (20MHz): MCS0-15
with Short Guard Interval Support (up to 144Mbps )11n (40MHz): MCS0-15 with Short Guard Interval Support (up to
300Mbps ).
l UDP throughput: up to 128Mbps
l Support UpnP
l 100M wide area network(WAN)
port x1
10M/100M local area network(LAN) port x4
Support RTS/CTS, Fragmentation and Defragmentation function
Support WMM , WMM-PS
Block Ack
Reverse Direction Data Flow
Link Adaptation
Roaming
Seamlessly roam and handover within mesh network
Adaptive mesh network routing establish and update
Wireless Frequency Range, 2.4 ~ 2.4835GHz ISM Band,
Radio and Modulation Type. IEEE 802.11b: DQPSK, DBPSK, DSSS, and CCK ; IEEE 802.11 g: BPSK, QPSK, 16QAM,
64QAM ; IEEE 802.11n: MCS0~MCS15;
l Transimission distance. 300 meters Outdoors, 100 meters Indoors coverage area(It’s limited in an environment.)
l Antenna
5dBi
l
l
l
l
l
l
l
l
l
l
l Transimission power. 802.11b: Typ. 18 dBm @Normal Temp Range; 802.11g: Typ. 15 dBm @ Normal Temp Range ;
802.11n: Typ. 15 dBm @ Normal Temp Range
External Connectors
l 4 10/100M local Ethernet Ports (RJ-45)
l 1 100M WAN port
Security Support
l
l
l
l
l
Three level login including local admin, local user and remote technical support access
Service access control based on incoming interface: WAN or LAN
Service access control based on source IP addresses
Protect DOS attacks from WAN/LAN: SYN flooding, IP surfing, ping of Death, fragile, - UDP ECHO (port 7), teardrop, land.
PAP (RFC1334), CHAP (RFC1994), MSCHAP for PPP session.
l IP filter, Parental control.
Environment
l Operating temperature: 0℃ to 40℃
l Storage temperature: -20℃ to 70℃
l Operating Humidity: 10%~95% no freezing
l Storage humidity: 5%~95% no freezing
Chapter 2
Hardware Installation
This chapter contains the information you need to install and set up the Wireless 2880AP.
the following topics:
n
Decide where to place the AP
n
Connecting the Access Point
n
Checking the LED indicators
n
Attaching an External Antenna
It covers
Decide where to place the AP
Place the AP in a dry, clean location near the hub, switch, computer or printer that will be connected
to the AP. The location must have a power source and be within the following distance of a Wi-Fi
compliant wireless LAN access point or wireless access point.
6
The key to maximizing the wireless range is to follow these basic guidelines:
n
Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances
that generate RF noise. The location should be away from transformers, heavy-duty motors,
fluorescent lights, microwave ovens, refrigerators.
n
Keep the number of walls and ceilings between the AP and other network devices to a minimum - each
wall or ceiling can reduce your AP’s range from 3-90 feet (1-30 meters.) Position your devices so
that the number of walls or ceilings is minimized.
n
Be a ware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters),
at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks
over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a
wall or ceiling (instead of at an angle) for better reception.
n
Building materials can impede the wireless signal - a solid metal door or aluminum studs may have
a negative effect on range. Try to position wireless devices and computers with wireless adapters
so that the signal passes through drywall or open doorways and not other materials.
Checking the LED Indicators
When the AP is connected to power, LEDs indicate activity as follows:
LED
Color
Activity
Power
Green
On: Power On
Off:Power Off
WLAN
Green
On: WLAN On
7
Blinking: sending/receiving data from wireless LAN
Off: Transmitter is off
LAN
Green
On: Good Link
Blink ing: sending/receiving data from LAN Port
Off: No link
WPS
Green
On:WPS Start’
Off:WPS Close
Security
Green
On:Security Start
Off:Security Close
Attaching an External Antenna
This AP comes with an antenna. It is external removable monopole signal-band 2.4 GHz antenna. It can be
rotated over 90 degrees and is omni-directional with a gain of less than 2 dBi. You can change a 5dBi
high gain antenna for creates a superior far-reaching wireless network
Charpter 3
CONFIGURING THE WIRELESS AP
If the default AP configuration does not meet your network requirements, or if you want to customize
the settings for your own network, you can directly connect to the device through it’s Ethernet port or
wireless to change the configuration. There are two typical applications:
1. Networks with a DHCP Server
If your network has a DHCP server, an IP address is automatic ally assigned to the AP. It takes between
one and two minutes for the Access Point to determine if there is a DHCP server on the network. After
you determine the AP’s IP address, you can enter that IP address into a web browser on a computer on
the same subnet to view the Access Point’s system status or change its configuration
2. Networks without a DHCP Server
If your network does not have a DHCP server, the Access Point uses a factory assigned IP address
(10.10.10.254). You can use that IP address to configure the Access Point, or you can assign a new IP
address to the Access Point.
To verify that the Access Point is using the default IP address assigned at the factory: Connect a
computer directly to the Access Point using the supplied standard Category 5 UTP Ethernet cable. Enter
the Access Point’s default IP address (10.10.10.254) into the computer’s web browser. If the
Configuration Management System starts, the Access Point is using the factory assigned IP address. You
can configure the Access Point with the Web interface:
Username, type admin (case sensitive)
Password, type admin
Click ok.
8
In the following, you will learn how to configure the basic functionsof your wireless AP.
Language Configuration
The 2880AP support multi-language.After login on the web UI ,You can click open all to choose the
Language English or Traditional Chinese from the drop list.And you can choose Status and Statics to
view information about the AP.
9
Operation Mode
You may configure the operation mode suitable for you environment.If you select Bridge mode,all
ethernet and wireless interfaces are bridged into a single bridge interface.If you select Gateway mode,
The first ethernet port is treated as WAN port. The other ethernet ports and the wireless interface are
bridged together and are treated as LAN ports.And here, you can set whether NAT enabled.
Click Cancel to close without saving, click Apply to save the settings.
Internet Settings
WAN
You may choose different connection type suitable for your environment. Besides, you may also configure
parameters according to the selected connection type.
10
Click Cancel to close without saving, click Apply to save the settings.
LAN
You may enable/disable networking functions and configure their parameters as your wish.
Click Cancel to close without saving, click Apply to save the settings.
11
DHCP Client
You could monitor DHCP clients here
Wireless Settings
Basic Wireless Settings
You could configure the minimum number of Wireless settings for communication, such as Network Name
(SSID) and Channel. The Access Point can be set simply with only the minimum setting items.
Network Mode
The 2880AP supports 11a, 11b, 11g, 11a/n mixed mode, 11b/11g mixed mode, 11b/g/n mixed mode.You can
configure the suitable network mode.
SSID
Service Set Identifier. This is the assigned name for a wireless Wi-Fi network. Stations must use this
unique identifier to communicate with an Access Point. The SSID can be any alphanumeric entry up to a
maximum of 32 characters.
MSSID
12
The Wireless AP supports Multiple SSID which allows it to act as multiple AP appearing in a Wireless
LAN network. You can configure up to 7 SSID on the device.
BSSID
Basic Service Set Identifier. This is the assigned MAC address of the station in the access point. This
unique identifier is in Hex format and can only be edited when Multi BSSID is enabled in the previous
screen.
SSID Broadcast
If you want to disable the broadcast of your SSID, you should check the Disable box. It also calls
Hide SSID.
Channel / Frequency
Select the channel for your wireless LAN in Channel/Frequency block. The default setting is Smart
Select it selects the channel which provides the best transmission quality. The frequencies available
vary depending which wireless mode you select.
WDS Link Settings
WDS (Wireless Distribution System) allows access points to communicate with one another wirelessly in a
standardized way. It can also simplify the network infrastructure by reducing the amount of cabling
required. Basically the access points will act as a client and an access point at the same time.
WDS is incompatible with WPA. Both features cannot be used at the same time. A WDS link is bidirectional, so the AP must know the MAC address of the other AP, and the other AP must have aWDS link
back to the AP.
Dynamically assigned and rotated encryption key are not supported in a WDS connection. This means that
WPA and other dynamic key assignment technologies may not be used. Only Static WEP keys may be used in
a WDS connection, including any STAs that are associated with a WDS repeating AP.
Enter the MAC address of the other APs you want to link to and click enable.
Supports up to 8 point to multipoint WDS links, check Enable WDS and then enable on the MAC addresses.
Example of a WDS topology:
AP1 <-- WDS --> Master AP (our AP) <-- WDS --> AP3<-- WDS --> AP4
13
HT Physical Mode
Click Cancel to clear the settings, click Apply to save the settings.
Advaced Wireless Settings
Use the Advanced Setup page to make detailed settings for the Wireless. Advanced Setup includes items
that are not available from the Basic Setup page, such as Beacon Interval, Control Tx Rates and Basic
Data Rates.
Basic Data Rate
Choose between the following data rates 1, 2, 5.5, 11, 6, 9 , 12, 18, 24, 36, 48,54 and auto. Default
is auto.
Beacon Interval
The interval time between 20ms and 500ms for each beacon transmission. The default is 100ms.
Data Beacon Rate (DTIM)
The Delivery Traffic Indication Message. Specify the data beacon rate between 1 and 255. Default is 1.
Fragment Length
The maximum packet size is used for fragmentation. Packets larger than the size programmed in this
field will be fragmented. The Fragment Threshold value must be larger than the RTS Threshold value.
The default is 2346.
RTS Threshold
Request to send threshold. The packet size that is used to determine if it should use the CSMA/CA
mechanism or the CSMA/CD mechanism
14
Click Cancel to close without saving, click Apply to save the settings.
Security
For example, when you select Security mode, you should config the Radius Sever inforamtion.
15
Click Cancel to close without saving, click Apply to save the settings.
WPS
You could setup security easily by choosing PIN or PBC method to do Wi-Fi Protected Setup.
Click Apply to save the settings.
If you enable WPS, you can view WPS status.
16
Station list
Through this page, you can easily identify the adjacent wireless stations. It will automatically
observe the adjacent wireless station’s ID (if specified), MAC address, SSID and current status.
Firewall
This section mainly introduce some ways to proctect youself through the following configuration.
17
MAC/IP/Port Filtering
You may setup firewall rules to protect your network from virus,worm and malicious activity on the
Internet.
Select MAC/IP/Port Filtering Enable, click Apply, then you start this function.you may define some
rules for the MAC/IP/Port Filtering Settings and apply.It is also very convenient for you to delete
these Settings.
Port Forwarding
This page enables you setup Virtual Servers to provide services on Internet.
18
Select Virtual Server Settings Enable form drop list, set the IP Address, Port Range, Protocol and
comment, click Apple to save the settings, click Reset to clear the data you input and you can easily
delete these rules from the Current Virtual Servers list.
DMZ
This page enables you to setup a De-militarized Zone(DMZ) to separate internal network and Internet.
19
System Security Settings
This page enables you to configure the system firewall to protect AP/Router itself from attacking.
Select Allow from drop down list, click Apply to save the setting , click Reset to select Deny.
Administration
Management
You may configure administrator account and password, NTP settings, and Dynamic DNS settings here.
20
Click Cancel to cancel the settings, click Apply to save the settings.
Upgrade Firmware
Upgrade the RT2880 firmware to obtain new functionality. It takes about 1 minute to upload
flash and be patient please. Caution! A corrupted image will hang up the system.
Click Reset to clear the firmware, click Apply to upgrade the firmware.
21
upgrade
Settings Management
You might save system settings by exporting them to a configuration file, restore them by importing the
file, or reset them to factory default.
Click Export to export the configuration file and click Import to import the configuration file and
click Load Default to reset the settings to factory default.
Status
The Web interface has been designed to enable you to easily perform advanced configuration tasks and
view information about the AP.
22
Statics
The Statics page shows all the statics information about your AP.
23
System Command
This page enable you to run a system command as root
Click Apply to run the command you put, click cancel to clear the command you put.
System Log
This page enables you to look and clear the system log.
Click Refresh to refresh the log, click Clear to clear the log.
24
FCC Notice:
This device must not be co-located or operating in conjunction with any other antenna or
transmitter
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
Federal Communications Commission (FCC) Requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
Regulatory information / Disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user
documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not
expressly approved by the manufacturer may void the user’s authority to operate the
equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of
this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of
the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its
authorized resellers or distributors will assume no liability for any damage or violation of government
CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated
with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Unauthorized antenna,
modification, or attachments could damage the transmitter and may violate FCC regulations.
MPE Statement (Safety Information)
Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal.
Safety Information
In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. Use only with supplied antenna. Unauthorized antenna,
modification, or attachments could damage the transmitter and may violate FCC regulations.
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement