null  null
DIGITAL WIRELESS 9” LCD
MONITORING SYSTEM
WITH SD CARD RECORDING
MODEL: Danrou KCM-7790DR
Feature list:

850nm IR Led visible distance up to 15m

9” TFT Lcd Digital panel (800 RGB x 480)

Two way audio

Scan function

PIR trigger or Video motion detect alert& recording

Manual recording

Touch button operation

Schedule recording separate settings from Monday to Sunday

Micro SD Card capacity up to 64GB

One LCD monitor can pair four cameras

Frame rate: Cam x 2 : 720p x1 @ 15 fps or Cam x 2 : VGA x2 @ 30 fps or Cam x 4 : VGA x 4 @ 15 fps

Individual recording files

5 Seconds pre-recording

LCD

Camera: 9v DC 600mA (+/-5%)

RF range: 150 meter (Line of sight)

Quad view
: 5v DC 2A Power adaptor (+/-5%)
Remote view and playback by Android or iOS smart phone
The system includes the following components:
Wireless Receiver
Front Panel buttons
1. LCD Screen – Displays video from the camera(s) or displays system operations.
Item Button
Function
2.
Enable two-way audio Intercom
:Talk back
3.
Activate / deactivate motion recording.
: Motion Recording
4.
Activate / deactivate manual recording.
: Manual Recording
5.
Switch between connected cameras.
: Change Channel
6.
: Quad / Sequence Mode
7.
Switch between Sequence and Quad (up to 4-channels)
viewing mode.
Switch between 2x digital zoom and normal viewing mode.
: Zoom
8.
Delete highlighted files in Playback mode.
: Delete File
9.
Open Main Menu. Return to previous menu / exit menus.
: Menu
10.
: Joystick
Move left / right / up / down to move the cursor in menus.
Push to enter Playback mode.
Back controls
1. Wireless Antennas: Position the antennas as needed for best reception.
2. Power Button: Press and hold to turn the receiver on / off. Press and release while the unit is
powered on to turn Scan mode.
3. Receiver Stand
4. Speaker
5. Stratus UID Number / QR Code: Unique ID number for connection to the system on a smartphone /
tablet.
6. Ethernet Port (RJ45): Connect the receiver to your router using the included Ethernet cable to enable
smartphone / tablet connectivity.
7. Power Port: Connect to a local power outlet using the included power adapter.
8. Volume Controls: Turn the receiver volume up and down.
9. micro SD Card Slot: Insert up to a 64GB micro SD card.
10. USB Port: Used for service purposes only.
11. Reset: Using a paper clip or other thin object, push the reset button to restore the system to its
default settings.
12. Power Indicator LED: Glows when receiver is connected to power.
Wireless Camera
1. IR LEDs – Infrared LEDs provide
viewing in no/low light conditions
2. Camera Lens –Catches the video in
front of the lens and transmits video from
camera to receiver.
3. PIR Sensor – Detects motion in front of the lens and
emits detection signal to transmitter.
4. Speaker – Produces the sound transmitted from the
receiver.
5. Camera Antenna – Sends & receives signals to or
from the receiver.
6. Wall Mounting Bracket – Use the bracket to mount the camera on a wall or other flat surfaces.
7. AC Adaptor Jack – Plug the AC adaptor to the jack for camera’s power supply.
8. Pair Button – The pair button is located on the back of the camera, it is used to pair the camera with
receiver.
Note: This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between day
mode and night vision mode, an audible clicking noise may be heard coming from the camera. This
clicking is normal, and indicates that the camera filter is working.
Camera Installation
Before you install the camera, carefully plan where and how it will be positioned, and where you will
route the cable that connects the camera to the power adaptor.
Before starting permanent installation, verify its performance by observing the image on the receiver
when camera is positioned in the same location/position where it will be permanently installed and the
receiver is placed in the location where it will be used most of the time.
Installation Warnings
·Aim the camera(s) to best optimize the viewing area: Select a location for the camera that provides a
clear view of the area you want to monitor, which is free from dust, and is not in line-of-sight to a strong
light source or direct sunlight.
· Avoid installing the cameras where there are thick walls, or obstructions between the Cameras and the
Receiver.
· Select a location for the camera that has an ambient temperature between 14°F~104°F(-10°
C~40°C)
· Not intended for submersion in water. For outdoor use, installation in a sheltered location is
recommended
Night Vision
This camera has built-in IR LEDs, which provides the camera with the ability to view images in no/low
light conditions.
Mounting Positions
You may mount your camera on a wall, ceiling, or counter. See the images below for recommended
configurations of the camera stand and antenna.
Wall
Ceiling
Counter
NOTE: For ceiling installation, position the antenna as high
as the ceiling allows. See the"Ceiling" mounting position in
the figure above.
To Install the Cameras
1. Use the included mounting screws to mount the camera to
the
mounting surface:
· Mark the positions of the screw holes on the mounting
surface.
· Drill holes and insert the drywall plugs (included) as needed.
· Firmly attach the camera to the mounting surface using the included
screws.
NOTE (1): If you are running the power cable through the mounting
surface, connect power before firmly attaching the camera to the
mounting surface.
NOTE (2): If you run the power cable along the mounting surface, the
cable must go through the cable notch on the camera base. This will
keep the camera base flush to the mounting surface.
NOTE (3): The camera can also be placed on a flat surface, such as a Table or Shelf, and no mounting
hardware is required.
2. Loosen the thumbscrews (1, 2) and the adjustment ring (3) by turning them counter clockwise.
3. Adjust the angle of the camera until the desired view is set. Tighten the thumbscrews and the
adjustment ring to secure the camera’s position.
NOTE: You can install additional cameras (maximum of 4 cameras). When adding cameras that were
not included in the original box, you will need to pair up the cameras with the receiver. Refer to the
camera pairing section of this manual.
4. Connect the power cable from the camera to the weatherproof power connector. Plug the power
adapter into a power outlet or surge protector.
NOTE: Power cables are only weatherproof when fully inserted at the connection point.
Power cables may not be submerged in water.
Make sure is the DC 9V for camera, and DC 5V for Receiver
Make sure the power adaptor is placed into a grounded outlet or surge bar to protect the camera from
power fluctuations.
1 Using the system
By default, the camera(s) included with your system are automatically paired to the receiver. The
camera(s) and receiver will communicate with each other once they are powered on.
Note: It is recommended to power on the cameras before powering on the receiver.
1.1 Understanding the On-screen Display
With camera 1 properly connected and powered on, the system displays a full-screen live view of the
camera.
With more than one camera properly connected and powered on, the system displays up to 4 channels
in split screen with the live view of each camera. The figure below shows the display configuration for 2
cameras connected.
1 Signal Indicator –The signal indicator shows the strength of the signal being received from the
camera. The number of bars in the Signal Indicator shows the strength of the signal. One or no bars
indicates the signal is poor, and 4 bars indicate a very strong signal.
Note
• If the signal is low (e.g.,1 or 2 bars) adjust the antennas, or reposition the cameras or receiver for
best performance.
• The signal indicator is not shown during Quad mode.
Signal Indicators:
OUT OF RANGE Warning
When the receiver can’t get signal from cameras, warning message will be displayed. Reposition the
camera, or check the camera power connection.
2
Channel Indicator–Displays the current channel number you are presently viewing. If viewing
multiple cameras at once, the camera indicator will appear above each video display.
Press Cam
button to view camera in manual switching mode.
Under Quad mode :
*Press
view button to enter automatically switch between channels.Press
view again to enter
Quad mode.
*Press joystick button 1.2.3.4 to accordingly switch available cam1,cam2,cam3,cam4.
3
micro SD Card Indicator – When a microSD card is inserted into the SD card slot, the indicator will
be shown on the LCD screen. A white icon shows that a microSD card with available recording space is
inserted in the receiver. A red icon indicates the microSD card is full.
4
Network status Indicator –A red icon
not connected to a network. A green icon
shows that the connection has failed or the system is
shows that the system is connected to the Internet and
tell you the monitor connect with internet mode. A yellow icon
shows that the system is connected
to the intranet and tell you the monitor connect with intranet mode.
Remote connection Indication- When a smartphone / tablet is accessing the system remotely, the
network status indicator changes to a remote connection icon
5
Talk back Indicator- Touch and hold
.
on the monitor then talk back to the camera, the indicator .
will be shown on the LCD screen.
6
Recording Indicator–"REC" appears when recording is in progress. If viewing and recording video
from multiple cameras at once, the recording indicator will appear above each video display where
recording is enabled
7 Zoom Indicator-Press the Zoom button on the front panel of monitor to enter “×2” mode, the
indicator will be shown on the LCD screen.
shows on the screen ,you can use the joystick button to
navigate to parts of the video that are outside the range of screen. Press zoom again to exit zoom mode.
8
Overwrite Indicator –Indicates Overwrite mode is on, which means the system will overwrite the
oldest recordings when the memory card is full. When you choose the overwrite function, the indicator
will be shown on the LCD screen
9
New Record Indicator- Indicates that there are new recordings saved to the microSD card.
10 Battery Indicator-Indicates the battery life of LCD monitor in low battery will show red and the
green LED under the indicator light will flash.
11
12
13
Time stamp-The current date and time on the system(month/date/year, hour/minute/second)
Motion recording indicator- Indicates that motion recording is turned on.
Volume indicator-Shows the current volume of the receiver. You must be in single channel
viewing mode to change volume,
14
2
New download icon-
indicate the volume 0.
appears on the screen if new firmware is available.
Viewing Modes
There are four different viewing modes available on the system: single channel viewing, Auto Sequence
Viewing mode (view individual channels automatically in sequence), Quad mode, and Scan mode.
Note: Auto Sequence Viewing mode cycles through connected channels in full-screen.
Use Quad mode to view up to four cameras simultaneously.
Use Scan mode, the receiver’s LCD screen and speaker will turn off unless motion is detected by one of
the cameras. The LCD screen turns on and displays video from the camera where motion was detected
for 15 seconds before turning off again. This conserves battery power and alerts you only when needed.
You can configure how much motion is needed to turn the display on in Scan mode by changing a
camera’s video motion detection settings. When exiting Scan mode, the receiver resumes live viewing in
Auto Sequence Viewing mode.
To change viewing modes:
Press
view to select between Quad mode (half-Quad mode when only 2 cameras are connected)
and Auto Sequence viewing mode. OR Press change channel icon to switch between channels 1~4 in
single channel view.
Quad mode
half- Quad mode
Note: When you only pair a camera or set one camera on(other three is off), there is no access to see
QUAD mode.
3
micro SD Card Recording
The system records video to the micro SD card (not included). You can manually record the video at your
desire or the receiver records when there is motion detected by the cameras and under the A/REC
function, or schedule recording based on the scheduled you set for each camera. Before recording, you
need to insert a micro SD card to the micro SD card slot. The system can support up to 64GB micro SD
card.
Recording Prerequisites: A micro SD card must be inserted into the receiver in order to record video.
You should always format the micro SD card prior to initial recording.
The following recording modes are available on the system: manual recording, schedule recording, and
motion recording. Record up to 4 channels at the same time.
3.1
Motion Recording
System only records when motion is detected by a camera(s).Press
receiver to start motion recording. There is a
Motion on the front panel of the
on the bottom right of corner. In this mode the
receiver starts recording prior to 5 seconds when motion detected by any activated camera. The
recording time can be set to 15s,30s or 1minitus after last detection. (Receiver support recording 4
camera at the same time in quad mode)
Press Motion again or press Rec to stop recording, after stopping recording press Motion to cancel
automatic recording mode.
3.2 Manual Recording
Press
Record on the front panel of the receiver to starts manual recording. Press the key again to
stop manual recording.
Note: In Quad view,it can continuous record from up to 4 cameras at a time.
3.3
Schedule Recording
Continuous or motion event recording from up to four cameras according to a weekly schedule . Set the
recording start time and end time, then switch on schedule recording in the menu to enable schedule
recording. In this mode the receiver records at a certain time every day.
3.4
Overwrite
Enter recording menu—overwrite—choose “yes” to activate overwrite function. Overwrite function can
automatically delete previous records when the micro SD card is full, and record new films.
4
Playback
Playback mode allows you to playback recorded video files from the micro SD card. You can view videos
or images directly on the system or by connecting the
micro SD card to your computer.
4.1
Video Playback
To playback recorded video on the system:
1. During live viewing, push joystick, The Recording File
List opens.
2. Move the Joystick up / down to change the displayed
month.
3. Select the channels you would like to view recordings
from:
• Move the joystick left / right arrow to select the
channel numbers
•Move the joystick up / down arrow to show or hide each channel on the calendar.
• Select the button with all four channels to show recordings from all connected cameras on the
calendar.
4. Once you have selected the month and the
channels to display on the calendar, push the
joystick to refresh the display. Dates that have
recordings available for playback are highlighted in
green.
5. Move the joystick left / right to select a date on
the calendar, and push the joystick to view a list of
recordings for that date.
Note:
• The system uses a 24-hour clock.
• Recordings are named by start time in hhmmss
format and the channel number (for example, the
recording 133245-2 began recording at 1:32:45 PM
on channel 2).
6. Select a file from the list and push the joystick to confirm then the selected file loads and playback
begins.. Move the joystick left / right to change pages to find video files quickly. The selected file loads
and playback begins.
4.2
Playback controls:
1. Playback duration: Shows the length of the recording
and how much has been viewed.
2. File name
3. Playback status: Shows whether the video is playing,
paused, or stopped.
To control playback using the joystick:
•LEFT: Rewind (2x > 4x > 8x > 16x).
•UP: Pause / Play video.
•RIGHT: Fast-forward (1x>2x > 4x > 8x > 16x).
•DOWN: Stop video.
• To change playback volume, press Volume
Controls on the side of the receiver.
To exit playback: Press
view.
Menu to return to the file list. Press
Menu repeatedly to return to live
4.3
Deleting Video Files
You can delete files on the micro SD card directly on the system. Delete files if you need to clear space
on the micro SD card (if file overwrite is disabled), or for your own file management purposes.
To delete files on the SD card:
1. From live viewing, press the joystick. The Recording File List opens.
2. Move the joystick up / down arrow to change the displayed month.
3. Move the joystick left / right arrow to select the channel numbers, and move the joystick up /down
arrow to show or hide each channel on the calendar. Select the button with all four channels to show
recordings from all connected cameras on the calendar.
4. When you have selected the month and channels to display on the calendar, push joystick to refresh
the display. Dates that have recordings available for playback are highlighted in green.
5. Move the joystick left / right arrow to select a date on the calendar, and push the joystick to view
recordings from that date.
6. Browse to the file you would like to delete. Press
on the front panel of the receiver.
7. A confirmation message appears. Select YES and push the joystick to delete the file.
8. Repeat the steps above for other files on the microSD card.
CAUTION:Do NOT delete folders on the microSD card using your computer. Deleting folders may affect
your access to other files on the card or may affect normal operation of the microSD card with the
system. If you want to delete the entire contents of the microSD card, it is highly recommended to format
the card using the system.
Viewing Video Directly from the micro SD Card
You can view the saved video files on your computer (PC or Mac) by using a SD card reader (not
included). Saved video files are in ASF format.
Note:1. Some PCs and Macs may have a SD card reader built-in. Please refer to your computer's
instruction manual for more details.
2. You can view ASF files natively in Windows Media Player, as well as other media players such as
VLC.
VLC is an open-source software application available at www.videolan.org
To playback recorded video on a PC:
1. Remove the micro SD card from the receiver by gently pushing on the micro SD card and then
releasing. The card will eject.
2. Insert the micro SD card into a SD card reader (not included) connected to your PC. Your PC should
load the micro SD card as a new Removable Drive and an Auto run window opens.
3. Click Open folder to view files or open the folder in Computer. Open the folder MFG.
You will then see a folder for each page of recorded video in Playback mode. Folders are named by page
number (e.g. recordings found on the second page are in the folder 00000002).
4. Double-click any of the ASF files. The video will begin playing in your default ASF media player.
5
Use
Accessing Menu System
Menu on the receiver to access to Menu system.
Use the joystick to move the cursor up/down/left/right in the menu, and push the joystick to open
sub-menus and confirm/save menu selections.
Press
Menu to exit menus without saving changes.
The Main Menu contains 5 submenus:
1. Settings –Use the menu for system settings, such as
date & time ,default setting, format memory, time zone,
network and firmware update.
2. Detect–Use the menu to set Camera’s motion detect
sensitivity ( High / Medium/ Low /Off )
3. Alert– Use the menu for Receiver beeps level, to alert
you when motion detected by camera. Press
/
to
decrease/increase the volume of the audio alarm. Press
OK to confirm the adjustment.
4. Record–Use the menu for micro SD card recording
settings.
5. Camera–Use the menu to add camera(s) to the receiver, adjust the camera on/off, adjust the
brightness, resolution for each camera.
5.1
Settings
- Date & Time: Set the date and time on the system.
Use
to select the item (MONTH,DAY
YEAR,HOUR,MINUTE,SECOND), and use
to set
the time.
Note:You can also synchronize the system time with an
Internet time server. Ensure there is a checkmark next to
Synchronize with an Internet time server then push the
joystick to confirm.
You must keep the system connected to your wireless
network using the included Ethernet cable
to synchronize with the Internet time server.
- Default Settings: Restore the system to default
settings (Default No).
Select Yes and then press OK to confirm. The system
takes a few moments to restore default settings.
Also you can see the firmware version V0.06-140822, when
you use a SD card to update the firmware, you can see
here to confirm whether you have done well.
NOTE: Restoring default settings does not affect files
recorded to the memory card or reset the date and time on
the system.
- Format Memory: Select Yes to format the micro SD
card. After formatting, all the data stored in the micro SD
card will be deleted.(default NO)
Note: Be cautious to use this function.
-Time Zone: Select the time zone where the system is
being used and enable / disable Daylight Savings Time
(DST). (Default is GMT+01:00)
-Firmware
Upgrade: Upgrade the system’s firmware.
Ensure the system is up-to-date with the latest firmware
for optimal performance. There are two ways to upgrade
firmware: from the server, or from a micro SD card.
A: To update firmware from server
1. Connect the included Ethernet cable from the
Ethernet port on the receiver to your router. The new
download icon (
) appears on the screen if new
firmware is available.
2. Press
, then move the joystick to select Settings.
3. Select Firmware Upgrade and push the joystick to
confirm.
4. Select From Server, then select Yes.
The system takes a few moments to install the latest
firmware.
5. After upgrading the new firmware, the monitor will automatically reboot .
CAUTION: During upgrading ,insure the connection of network is okay and do not plug out
power during upgrading.
B:To update firmware from micro SD card
1. Insert the micro SD card into the included adapter. Insert the adapter into the SD card reader (not
included) on your PC or Mac.
2. Download the latest firmware and transfer it to the root folder on the micro SD card.
3. Once the transfer is complete, insert the micro SD card into the card slot on the receiver.
4. Press
, then move the joystick to select Settings.
5. Select Firmware Upgrade and push the joystick to confirm.
6. Select From SD Card, then selected Yes. The system takes a few moments to install the latest
firmware.
7. After upgrading the new firmware, the monitor will automatically reboot .
CAUTION: During upgrading
, do not plug out power during upgrading.
-Network: Configure the receiver’s IP address (advanced),
view network information, or reset your remote access
password.
1. Networking setting: IP Addressing Options,to select the
Static IP and Dynamic IP
CAUTION: This section is for advanced users only.
Note
• Dynamic IP addressing is enabled by default.
• A static IP address is not required for remote access to
the system.
• You may have to configure your router settings if the
DHCP server is enabled.
2.Information:Set up the Static IP address and Dynamic IP
on/off, display the current network information(IP State, IP
Address, default gateway, MAC address ,UID as pasted on
the back of monitor ,etc).
3. Reset password: Reset the password of remote access by
000000
5.2
Detect
Separately to Set each Camera’s motion detect sensitivity
(High, Medium, Low, Off), move the joystick to select the
level of sensitivity then Push the joystick to confirm the
adjustment.(Default Low)
5.3
Alert
Increase or decrease the volume of the buzzer when motion
is detected by the camera(s). If you want to turn off the buzzer,
turn the alert volume to the mini-mum setting (Default 0).
To increase/decrease alert volume:
1. Press Menu then select Alert. Push the joystick to confirm.
2. Move the joystick right arrow to increase the alarm volume,
or left to decrease the alarm volume. Set the volume all the
way to the left to disable the alarm buzzer and button sounds.
3. Push the joystick to save your settings.
4. Press Menu until all menus are closed.
5.4
Record
Use the Record menu to change Duration(motion recording time), set a recording schedule, and
enable/disable overwrite.
You can set up the recording parameters in record menu.
Note: To use the recording function, make sure a micro SD
card is inserted into the micro SD card slot.
- Duration: The recording time when there is motion detected
by a camera in automatic recording mode. The recording time
can be set to 15s ,30s or 1 minute. (Default 15s)
- Schedule Recording: Use scheduled recording to have
the system automatically record continuously according to
a selected start and stop time. Scheduled continuous
recording will record constantly。
Set a recording schedule:
1. Press Menu, then select Record. Push the joystick to confirm.
2. Move the joystick to select Schedule Recording.
3. Move the joystick left / right arrow to view existing recording schedules for each day of the week.
Continuous recording schedules appear as green bars, while motion recording schedules appear as
orange bars.
4. Push the joystick to create a new recording schedule.
5. Select the channels that will use this recording schedule.
Move the joystick left / right arrow to move the cursor and
push the joystick to include or dismiss the channel.
6. Select the start time and end time for schedule recording
by moving the joystick left /right arrow to move the cursor,
then up / down to change the values.
Note: The time uses a 24-hour clock.
7. Select which days to apply the recording schedule to by
moving joystick left /right arrow to move the cursor, then
push the joystick to include or dismiss a day.
8. Move the joystick left / right arrow to select Save, then push the joystick to create a continuous
recording schedule. Select Save when finished to save your settings.
9. Press Menu until all menus are closed.
Stopping Scheduled Recording
When the stop time arrives, the system stops recording automatically. If necessary, you can stop
schedule recording manually.
To stop schedule recording: Press
Manual Record to stop schedule recording.
To stop schedule recording: Press Rec to stop schedule recording. But this way just to cancel the
recording at most 30mintues,if you want to stop it forever, please do it as below.
Modifying or Deleting a Recording Schedule
You can modify any recording schedule by adding or subtracting recording time.
To modify /delete a recording schedule:
1. Press Menu , then select Record. Push the joystick to confirm.
2. Select Schedule Recording.
3. Move the joystick up / down arrow to select Modify and push the joystick to confirm.
4. Select which channels to change the schedule for by moving the joystick left / right arrow to move the
cursor, then push the joystick to include or dismiss the channel.
5. Select the start time and end time for the modification. This could be a span of time you wish to add to
or subtract from an existing schedule. Move the joystick left / right arrow to move the cursor, then move
the joystick up / down arrow to change the start and end time.
6. Select which days of the week to apply the modification to by moving the joystick left /right arrow to
move the cursor, then push the joystick to include or dismiss a day
7. Move the joystick left / right arrow to select the type of modification:
• Select Save to add onto a continuous schedule.
• Select Delete to subtract from either type of schedule.
8. Press Menu until all menus are closed.
Note: If you delete a recording schedule during a scheduled recording time, the camera(s) will continue
to record video for a short period afterwards. The system checks for changes in recording schedules
every half hour and will eventually stop recording if a schedule has been deleted.
- File Overwrite: Use the overwrite feature to have the system overwrite the oldest recorded data on the
mirco SD card once the micro SD card is full
5.5
Camera Setup:
- Pairing:
The system comes with camera(s) that have already
been paired. These cameras will communicate with the
receiver once powered on.
The pairing function assigns each camera to a different
channel on the wireless receiver (up to 4 cameras), and
is necessary for configuring additional cameras.
NOTE: It is highly recommended to pair the cameras to
the receiver before permanently mounting the cameras.
1. Power on the camera by connecting it to power outlet with supplied 9V power adaptor.
2. Power on the receiver by connecting it to power outlet with supplied 5V power adaptor.
3. Press the
Menu on the receiver. Move the joystick to select the camera and the pairing ,
(If you pair a new camera to a channel that is already being used by an existing camera, the new camera
will be connected to that channel. The old camera will automatically be disconnected.
4. Push the joystick then select the channel you wish to pair the camera to, push the joystick to confirm.
5. A message will be displayed on the receiver screen.
The receiver will count down from 30~0 – you must press the Pair button on
the camera during this time to successfully pair the camera. If the button on
the camera is not pressed, the receiver will return to the view screen, and no
pairing will take place.
6. Following the on-screen prompt, press the Pair button on the back of the
camera. You have 30 seconds to press the Pair button on the
camera, once paired, after 3s will see the live video on monitor .
-Camera On/Off :
Select a camera by moving the joystick up/down, then
move the joystick left/right to switch on or switch off the
camera.
Push the joystick to confirm the change and exit.
NOTE: The currently selected camera will have On/Off
highlighted in Green. Any disabled channels will be
blacked out in Quad mode when you pair 4 cameras.
-Brightness:
To adjust camera brightness:
1. Press Menu then select Camera. Push the joystick to
confirm.
2. Select Brightness.
3. Move the joystick up/down to select the camera you
wish to configure brightness for.
4. Move the joystick to the right to increase the brightness
level for the selected camera, or left to decrease
brightness. Camera brightness is measured on a scale of
1-6 where1 is the darkest and 6 is the brightest. Push the
joystick to save changes. ( default 3)
5. Press the button to exit.
6. Repeatsteps1~4 to configure your other cameras as
needed.
-Resolution:
Select the frame rate for each camera by HD or VGA
Frame rate: Cam x 2 : 720p x1 @ 15 fps or Cam x 2 : VGA x2 @ 30 fps or Cam x 4 : VGA x 4 @ 15 fps
6
Scan mode
In Scan mode, the receiver’s LCD screen and speaker will turn off unless motion is detected by one of
the cameras. The LCD screen turns on and displays video from the camera where motion was detected
for 15 seconds before turning off again. This conserves battery power and alerts you only when needed.
You can configure how much motion is needed to turn the display on in Scan mode by changing a
camera’s video motion detection settings.
To enable Scan mode:
1. Enter live viewing mode.
2. Press the power button on top of the receiver.
3. Press the power button again to exit Scan mode.
6. Android and iOS App Remote view
Use the free MyCam View app to conveniently connect to your system on a smartphone /
tablet. The mobile app is free with no recurring fees. View live video from the camera(s)
from anywhere with an Internet connection.
6.1 System Requirements
• You must have a high-speed Internet connection to view live video using the mobile app.
Traffic congestion may result in choppy video.
• When using a mobile cellular network, data charges may apply. Check with your provider
for details.
6.2
MyCam View for Android Devices
Getting Started: Use the following instructions to view your camera(s) over the Internet
using your Android™ smartphone or tablet.
1. Connect the included Ethernet cable from the Ethernet port on the LCD receiver to
your wireless router. The network icon on the receiver turns green (
).
• You may need to turn the receiver off and on again for it to connect to your network.
2. Connect to your home WiFi Internet using your Android™ smartphone or tablet.
3. Download app MyCam View freely from the Google player store on your smart phone or
tablet.(Make sure your phone connect with network)
4. Tap the MyCam View icon (
) to launch the APP.
5. Tap Click here to add device.
6. Then the pictures as showed, there are 2 options to get the UID from the monitor.
Option A: Tap Scan button to scan the QRcode on the back of monitor.
Option B: Enter the UID printed below the
QRcode(example:D7ETGG7YPUUZUNPYWM4J) as it shows on the back of monitor.
Name: Enter a personalized name(original name is MyCam View) for the system in the
Name field, then enter the password (default 000000).
7. Tap OK. The system
an "Online" status.
will show in your device list with
If it shows Failed, please tap
then select reconnect.
8. Tap the name of the system. You will be asked to enter a new, secure password.
Write your password down for future reference: _____________________________
Live video from the camera(s) appears on your smartphone or tablet.
6.2.1
Live Viewing
1. System information: The system name followed by the channel currently displayed.
2. Network status
3. Viewing resolution: Streaming resolution for the video feed.
4. Channel button
: Tap to choose which channel to display.
5. Online:1,only one remote visit, system support 4 remote visit at the same time.
Video quality: Speed of video decoding. Speed of video decoding. Higher quality results
in greater bandwidth consumption, which requires a higher connection speed. Reduce
quality if video is choppy.
6. Live video
7. Image gallery
8. Snapshot
9. Mute
: Tap to view snapshot images taken using the app.
: Tap to take a snapshot of the current video display.
: Tap to mute or unmute sound from the current camera.
10. Intercom
: Tap to enable two-way audio with the currently selected camera. Tap
again to disable or listen for a response.
6.2.2
Event Log
If you have enabled motion recording on the system, use the event log to review
motion-based events. Each event is stamped with the date and time when the event took
place, as well as the camera that captured the event. These events are uploaded from the
memory card inserted into the receiver. If the memory card is removed, the events will not
be accessible.
Note: Date and time stamps are created using the date and time on your smartphone or
tablet and not the receiver
To open the event log:
1. Back to the add camera menu, then press the down arrow
2. Tap View Event.
A list of events appears from the nearest 24hours. If you wish to view an event which took
place prior to the current date, use the search feature detailed below.
3. Tap an event to preview the video recording.
You can also search for events by specifying a time frame or specific channels.
To search for events:
1. Tap
next to the system name.
2. Tap View Event.
3. Tap
.
4. Choose a time frame to search for video, or tap Custom to configure the start time, end
time, and channels included. Tap Ok to begin the search.
A list of recordings that meet the specifications of your search appears.
5. Tap any recording to preview it on your device.
NOTE: There is not available to rewind or speed the video when you remote access to
view the video, also the video has no sound.
6.2.3
Modify Password
Change the password used for remote access to the system. You can also revert the
password to the default directly on the receiver (default password: 000000)
To modify your password:
1. Tap
next to the system name.
2. Tap Edit Device.
3. Tap Advanced.
4. Tap Modify Password.
5. Enter the following information:
• Old: Enter the current password for the
system.
• New: Enter a new password.
• Confirm: Reenter the new password.
6. Tap OK.
To revert to the default password:
1. Press Menu then push the joystick to select Settings.
2. Select Network.
3. Select Reset Password.
4. Select Yes.
5. Press Menu to exit.
6.2.4
Viewing Snapshots
View snapshots taken with the cameras using the app.
1. Tap
next to the system name.
2. Tap View Snapshot.
3. Tap any picture to view it
in
full screen.
In view list, tap any small icon of picture and hold 2 seconds, there is a caution: Are you
sure to delete this snapshot?, if you want ,please select Yes, if not, select No.
6.2.5
Setting Alert Interval
The alert interval determines the minimum amount of time between motion alerts on your
smartphone / tablet. You may want to increase the interval length to decrease the
frequency of alerts on your smartphone / tablet, or even turn smartphone / tablet alerts off.
By default, the alert interval is set to 3 minutes.
1. Tap
next to the system name.
2. Tap Edit Device.
3. Tap Advanced.
4. Tap Alert Interval.
5. Tap one of the time intervals to set the minimum time ( between motion alerts. Select
Unlimited to receive alerts whenever a motion event occurs, or select OFF to turn off motion
alerts on your smartphone / tablet.
Get the push notification: please make sure that you have done it below:
Open your smartphone/tablet setting, find the Application manager and open it to select the
MyCam view App, tap it , then new picture pops out, please select √ Show notifications.
After doing this, and you set the alert interval except OFF, then you can receive the push
notification.
6.2.6
Setting Video Quality
Video quality affects the smoothness of the live video feed on your smartphone or tablet.
1. Tap
next to the system name.
2. Tap Edit Device.
3. Tap Advanced.
4. Tap the dropdown menu next to Video Quality.
5. Tap High, Medium, or Low. High video quality results in greater bandwidth consumption,
which requires a high speed connection. Reduce quality if video is choppy.
Remove Device: Delete this camera from your phone
6.3
MyCam View for iOS Devices
Getting Started: Use the following instructions to view your camera(s) over the Internet
using your iPhone® or iPad®.
1. Connect the included Ethernet cable from the Ethernet port on the LCD receiver to
your wireless router. The network icon on the receiver turns green (
).
• You may need to turn the receiver off and on again for it to connect to your network.
2. Connect to your home WiFi Internet using your smartphone or tablet. See the user
guide provided with your iPhone® or iPad® for details.
3. Download the free MyCam View app from the App Store. (Make sure your phone
connect with network)
Note: For iPad users, check on the app store for iPhone app.
4. Tap the MyCam View icon (
) to launch the APP.
5. Tap Add Device, Tap Add
OR
Tap QRCode to scan the QR code on the back
of the receiver if your mobile device does not
have a camera.
You can also tap
to search for the system on the network. This option is only
available if your smartphone or tablet is connected to the same network as the receiver.
Name: Enter a personalized name(original name is MyCam View) for the system in the
Name field, then enter the password(default 000000).
Note: If you tapped Add in the previous step, enter the UID number printed on the QR code
label on the back of the receiver. Otherwise, the UID field will be populated automatically.
6. Tap Save. The system will show in your device list with an "Online" status.
7. Tap the name of the system. You will be asked to enter a new, secure password.
Write your password down for future reference: _____________________________
Live video
from the camera(s) appears
on your
smartphone or tablet.
6.3.1
Live Viewing
1. System information: The system name followed by the channel currently displayed.
2. Network status
3. Viewing resolution: Streaming resolution for the video feed.
4. Channel button
: Tap to choose which channel to display.
5. Online: 1,only one remote visit, system support 4 remote visit at the same time.
Video quality: Speed of video decoding. Speed of video decoding. Higher quality results
in greater bandwidth consumption, which requires a higher connection speed. Reduce
quality if video is choppy.
6. Live video
7. Image gallery: Tap to view snapshot images taken using the app.
8. Snapshot: Tap to take a snapshot of the current video display. You can also share
snapshots via e-mail. See 6.3.6 Sharing Snapshots.
9. Mute: Tap to mute or unmute sound from the current camera.
10. Intercom: Tap to enable two-way audio with the currently selected camera. Tap again
to disable or listen for a response.
6.3.2
Event Log
If you have enabled motion recording on the system, use the event log to review
motion-based events. Each event is stamped with the date and time when the event took
place, as well as the camera that captured the event. These events are uploaded from the
memory card inserted into the receiver. If the memory card is removed, the events will not
be accessible.
Note : Date and time stamps are created using the date and time on your iphone or ipdad
and not the receiver.
To open the event log:
1. Tap
.
2. Tap the UID for the system.
A list of events appears from the last day. If you wish to view an event which took
place prior to the current date, use the search feature detailed below.
3. Tap an event to preview the video recording.
You can also search for events by specifying a time frame or specific channels.
To search for events:
1. Tap
.
2. Tap the UID for the system.
A list of events appears.
3. From the event list, tap .
4. Choose a time frame to search for video, or tap Custom to configure the start time, end
time, and channels included. Tap Done to begin the search. A list of recordings that meet
the specifications of your search appears.
5. Tap any recording to preview it on your device.
6.3.3
Modify Password
Change the password used for remote access to the system. You can also revert the
password to the default directly on the receiver (default password: 000000).
To modify your password:
1. Tap
next to the system name.
2. Tap Advanced Setting.
3. Tap Modify Password.
4. Enter the following information:
• Old: Enter the current password for the system.
• New: Enter a new password.
• Confirm: Reenter the new password.
5. Tap OK.
To revert to the default password:
1. Press Menu, then push the joystick to select Settings.
2. Select Network.
3. Select Reset Password.
4. Select Yes.
Press Menu to exit.
6.3.4
Setting Alert Interval
The alert interval determines the minimum amount of time between motion alerts on your
iphone / iPAD . You may want to increase the interval length to decrease the frequency of
alerts on your iphone / iPAD, or even turn iphone / iPAD alerts off. By default, the alert
interval is set to 3 minutes.
1. Tap
next to the system name.
2. Tap Edit Device.
3. Tap Advanced Setting.
4. Tap Alert Interval.
5. Tap one of the time intervals to set the minimum time between motion alerts. Select
OFF to turn off motion alerts on your iphone / iPAD.
Get the push notification: please make sure that you have done it below:
1. Open your iphone / iPAD setting, find the Notification Center and tap it to select the
MyCam view App.
2. Tap MyCam View , then new picture pops out, please turn on the Sound.
After doing this, and you set the alert interval except OFF, then you can receive the push
notification.
6.3.5 Setting Video Quality
Video quality affects the smoothness of the live video feed on your smartphone or tablet.
Video smoothness is affected by connection speed.
1. Tap
next to the system name.
2. Tap Advanced Setting.
3. Tap Video Quality.
4. Tap High, Medium, or Low. High video quality results in the most bandwidth
consumption, which requires a high speed connection. Reduce quality if video is choppy.
6.3.6
Sharing Snapshots
Share snapshots with friends and family via e-mail.
1. Tap
.
2. Tap the name of the system you wish to share snapshots from.
3. Tap
.
4. Tap the snapshot you want to share, then tap
5. Select Email Photo to share the snapshot.
.
6. Enter the recipient’s email address and tap Send.
Electrical Parameter:
Camera(s)
Transmit Frequency Range
2400Mhz~2483.5Mhz
Data Rate
4 Mbps
Transmitting Power
16dBm (TYP)
Modulation Type
GFSK with FHSS
Transmitting Distance
150m (Line of Sight)
Image Sensor Type
1/4” Color CMOS Image Sensor
Effective Pixels
H: 1280 V: 720
Image Processing
MPEG-4
Cam x 2 : 720px1 @ 15 fps
Image Resolution / Frame Rate
Cam x 2 : VGAx2 @ 30 fps
VGA x 4 @ 15 fps
Lens
3.6mm / F2.0 (ICR cut Filter)
Viewing Angle (Diagonal)
64° (FOV)
IR LED / Night Vision Range
24 Leds / 850nm, 15m (with IR Led)
Power Requirement
9V DC 600mA ±5%
460mA Max (with IR On and talk back)
Power Consumption
240mA Max (with IR Off / without talk back)
Operating Temperature
14°F ~ 104°F (-10°C ~ 40°C)
Operating Humidity
0% ~ 85%
Lcd monitor
Receiving Frequency Range
2400Mhz~2483.5Mhz
Data Rate
4 Mbps
Receiving Sensitivity
-81dBm
Modulation Type
GFSK with FHSS
Lcd Panel size
9 Inch
Lcd Resolution
800 RGB (H) x 480 (V)
View Angle
H: 140° V: 110°
Power Requirement
5V DC 2A ±5%
Power Consumption
1050mA Max
Operating Temperature
14°F ~ 104°F (-10°C ~ 40°C)
Operating Humidity
0% ~ 85%
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement