NewAge Products Home Bar 14-Bottle White Woodgrain Bar Cabinet Use and Care Manual
Add to my manuals58 Pages
advertisement
HOME BAR SERIES
3 DRAWER BASE
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install wine cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
220 lbs.
55 lbs.
55 lbs.
55 lbs.
55 lbs.
3 Drawer
Base Cabinet
Max 440 lbs.
Countertops
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinet
96” Countertop. Covers over 4 Cabinet
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Parts Supplied
Handles
Handle Bolts (M4 x30mm)
#8 x 25mm Screws
3 Drawer
Cabinet
3
6
6
Handle Handle Bolt
M4 x 30mm
Tools Needed
1 x #2 Phillips head
screwdriver
Screws
#8 x 25mm
1 x #2 Phillips Bit
(opitional)
1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure 1 x Drill Bit
2.5mm or 3/32”
1 x Flashlight
(optional)
Installing the Handles
1 Parts Needed.
2
Note:
Cabinets come with handles installed on inside of drawers/doors.
Align handle to holes on doors or drawers.
3 x Handle 6 x Handle Bolt
(M4x 30mm)
3
Screw in bolts.
Removing Drawer
4
Extend drawer fully.
5 Press plastic triggers on underside of drawer according to arrows in image.
6 Tilt and remove shelf rack.
Inserting Drawer
10
3
Partially extend drawer slides.
11 Put drawer on slides and slide each drawer slide forward until you hear a click sound.
Fastening Cabinets
9 Parts Needed.
Note:
All drawers must be removed prior to fastening cabinets together.
10 Drill 3/32” pilot holes on interior wall of cabinet being fastened.
4 - #8 x 25mm screws
11 Using pilot hole as guides, screw into second cabinet.
Do not over-tighten screws and punch through other side!
X4
Mounting the Worktop
12 Parts
Needed.
13 Place worktop over cabinets and lower onto cabinets.
4 - #8 x 25mm screws
14 Drill 3/32” pilot holes on interior roof of cabinet.
15 Tighten screws to secure cabinets.
3
X4
HOMEBAR SERIES
WINE STORAGE CABINET
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install wine cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
220 lbs.
65 lbs.
65 lbs.
65 lbs.
65 lbs.
Bottle Cabinet
Max 480lbs.
Countertops
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinets
96” Countertop. Covers over 4 Cabinets
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Parts Supplied
Handles
Handle Bolts (M4 x 22mm)
#8 x 25mm Screws
Bottle
Cabinet
2
4
6
Handle Handle Bolt
M4 x 22mm
Screws
#8 x 25mm
Tools Needed
1 x #2 Phillips head
screwdriver
1 x #2 Phillips Bit
(opitional)
1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure 1 x Drill Bit
2.5mm or 3/32”
1 x Flashlight
(optional)
Installing the Handles
1 Parts Needed.
Note:
Cabinets come with handles installed on inside of drawers/doors.
2 Align handle to holes on doors or drawers.
2 x Handle 4 x Handle Bolt
(M4 x22mm)
3
Screw in bolts.
Removing Pull-out Rack
4
Partially extend rack.
5 Pull right side latch up.
Right Side
6
Push left latch down.
Left Side
7 Slide rack out.
Slide Out
Inserting Drawer
8 Align rails and slide in.
Slide In
Fastening Cabinets
9
Parts Needed.
Note:
Remove wine rack and pull-out rack to make fastening cabinets easier.
10 Drill 3/32” pilot holes on interior wall of cabinet being fastened.
4- #8 x 25mm screws
11 Using pilot hole as guides, screw into second cabinet.
Do not over-tighten screws and punch through other side!
X4
Mounting the Worktop
12 Parts
Needed.
13 Place worktop over cabinets and lower onto cabinets.
4- #8 x 25mm screws
14 Drill 3/32” pilot holes on interior roof of cabinet.
15 Tighten screws to secure cabinets.
3
Adjusting The Door Hinges
Using a Philips screwdriver, the doors can be adjusted:
Left, right, forwards and backwards.
16 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.
A
17 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
B
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
HOME BAR SERIES
DISPLAY BASE
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install wine cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
220 lbs.
25 lbs.
25 lbs.
25 lbs.
205 lbs.
Bottle Display
Base Cabinet
Max 500lbs.
Countertops
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinet
96” Countertop. Covers over 4 Cabinet
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Parts Supplied
Handles
Handle Bolts (M4 x 22mm)
Adjustable Display Racks
Shelf Pins
Bottle Display
Cabinet
2
4
3
14
#8 x 25mm Screws 6
Handle Display Racks
Tools Needed
1 x #2 Phillips head
screwdriver
Shelf Pins Handle Bolt
M4 x 22mm
Screws
#8 x 25mm
1 x #2 Phillips Bit
(opitional)
1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure 1 x Drill Bit
2.5mm or 3/32”
1 x Flashlight
(optional)
Installing the Handles
1 Parts Needed.
Note:
Cabinets come with handles installed on inside of drawers/doors.
2 Align handle to holes on doors or drawers.
2 x Handles 4 x Handle Bolt
M4 x 22mm
3
Screw in bolts.
Fastening Cabinets
4 Parts Needed.
5
Note:
All shelves must be removed prior to fastening cabinets together.
Drill 3/32” pilot holes on interior wall of cabinet being fastened.
4- #8 x25mm screws
6 Using pilot hole as guides, screw into second cabinet.
Do not over-tighten screws and punch through other side!
X4
Mounting the Worktop
7 Parts
Needed.
8 Place worktop over cabinets and lower onto cabinets.
4- #8 x25mm screws
9 Drill 3/32” pilot holes on interior roof of cabinet.
10 Tighten screws to secure cabinets.
Inserting Cabinets Shelves on an angle
11 Open cabinet doors. Attach shelf clips to desired height.
12 The shelf supports are inserted into front and middle hole positions.
Insert rack at a slight angle and position over shelf supports.
14 Lower shelf down onto shelf supports.
15 Ensure shelf supports sits in groove on lower edge of rack.
16 Insert remaining shelves.
Inserting Cabinets Shelves Horizontal
17 Open cabinet doors. Attach shelf clips to desired height.
18 The shelf supports are inserted into front and back holes.
19 Insert rack at a slight angle and position over shelf supports.
20 Lower shelf down onto shelf supports.
21
Lower shelf down onto shelf supports.
22 Insert remaining shelves.
Adjusting The Door Hinges
Using a Philips screwdriver, the doors can be adjusted:
Left, right, forwards and backwards.
23 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.
A
24 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
B
HOME BAR SERIES
SHORT WALL DISPLAY
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
50 lbs.
25 lbs.
25 lbs.
50 lbs.
Short Display
Cabinet
Max 150lbs.
Countertops
(for Base cabinets only)
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinets
96” Countertop. Covers over 4 Cabinets
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools.
• See “Parts” and “Tools Needed” in the list below.
Parts
Supplied
Threaded Caps
Threaded Washer
Handles
Handle Bolts ( M4 x 22mm)
#8 x 25mm Screws
Lag Screw ( 6 mm x 55 mm)
Glass Shelves
Shelf Pins
Tall Wall Display
Cabinet
4
4
2
2
4
4
2
10
Glass Shelves Shelf Pins
Handle Screws
#8 x 25mm
Handle Bolt
M4 x 22mm
Lag Screw
6mm x 55mm
Threaded
Washer
Threaded
Caps
Tools Needed
1 x #2 Phillips head
screwdriver
1 x #2 Phillips Bit
(opitional)
1 x Stud Finder 1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure
1 x
2.5mm or 3/32”
drill bit
1 x
6.5 mm or 1/4”
drill bit
1 x Flashlight
(optional)
Installing the Handles
1 Parts Needed.
2
Note:
Cabinets come with handles installed on inside of drawers/doors.
Align handle to holes on doors or drawers.
2 x Handle 4 x Handle Bolt
M4 x 22mm
3
Screw in bolts.
Inserting Glass Shelves
4 Open cabinet doors. Install shelf pins at desired height.
5 Ensure pins are installed at level height.
6 Insert glass shelf at a slight angle.
7 Position over shelf supports .
8 Lower shelf down onto shelf supports.
9 Repeat steps 1-4 for second shelf.
Mounting Cabinets
10 Use stud finder to locate the studs and mark the wall with a pencil.
11 Gather parts.
4 x Lag Screw
6mm x 55mm
4 x Threaded
Washer
4 x Threaded
Caps
12 Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs. Repeat for drilling two holes near the bottom of the cabinet.
Pilot Holes
13 Place cabinet flush against wall and attach using screws and washers.
14 Use threaded caps to cover screws.
Fastening Cabinets
15
Parts Needed.
Note:
All shelves must be removed prior to fastening cabinets together.
16 Drill 3/32” pilot holes on interior wall of cabinet being fastened.
4 - #8 x 25mm screws
17 Using pilot hole as guides, screw into second cabinet.
Do Not Over-tighten screws and Punch through other side!
Adjusting The Door Hinges
Using a Philips screwdriver, the doors can be adjusted:
Left, right, forwards and backwards.
18 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.
A
19 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
B
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
HOME BAR SERIES
SPLIT CABINET
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install wine cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
220 lbs.
55 lbs.
25 lbs.
200 lbs.
Split
Base Cabinet
Max 500 lbs.
Countertops
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinets
96” Countertop. Covers over 4 Cabinets
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Parts Supplied
Door Handles
Drawer Handles
Handle Bolts for Doors (M4x22mm)
Handle Bolts for Drawers (M4x30mm)
#8 x 25mm Screws
Shelf
Shelf Clips
Split
Cabinet
2
2
6
1
6
1
4
Door Handle
Shelf
Drawer Handle
Tools Needed
Shelf Pins Door
Handle Bolt
M4 x 22mm
Drawer
Handle Bolt
M4 x 30mm
Screws
#8 x 25mm
1 x #2 Phillips head
screwdriver
1 x #2 Phillips Bit
(opitional)
1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure 1 x Drill Bit
2.5mm or 3/32”
1 x Flashlight
(optional)
Installing Drawer Handle
1 Parts Needed.
2
Note:
Cabinets come with handles installed on inside of drawers/ doors.
Align handle to holes on doors or drawers.
1x Handle 2x Drawer
Handle Bolt
M4 x 30mm
3
Screw in bolts.
Installing the Handles
4 Parts Needed.
5
Align handle to holes on doors or drawers.
2 x Handles 4 x Door
Handle Bolt
M4 x 22mm
6
Screw in bolts.
Inserting Shelf
1 Open cabinet doors. Attach shelf clips to desired height.
2 Ensure clips are at level height.
3 Insert shelf at a slight angle.
4 Position over shelf supports . Lower shelf down onto shelf supports.
5
Removing Drawer
7
Extend drawer fully.
8 Press plastic triggers on underside of drawer according to arrows in image.
9 Tilt and remove shelf rack.
Inserting Drawer
10
3
Partially extend drawer slides.
11 Put drawer on slides and slide each drawer slide forward until you hear a click sound.
Fastening Cabinets
12
Parts Needed.
Note:
All shelves and drawers must be removed prior to fastening cabinets together.
13 Drill 3/32 pilot holes on interior wall of cabinet being fastened.
4 - #8 x 25mm screws
14 Using pilot hole as guides, screw into second cabinet.
Do not over-tighten screws and punch through other side!
X4
Mounting the Worktop
15 Place worktop over cabinets and lower onto cabinets.
4 - #8 x 25mm screws
16 Drill 4, 3/32” pilot holes on interior roof of cabinet.
17 Tighten screws to secure cabinets.
3
Adjusting The Door Hinges
Using a Philips screwdriver, the doors can be adjusted:
Left, right, forwards and backwards.
18 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.
A
19
To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
B
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
HOME BAR SERIES
TALL DISLAY
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install wine cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
50 lbs.
25 lbs.
25 lbs.
25 lbs.
50 lbs.
Tall Display Cabinet
Max 175 lbs.
Countertops
(for Base cabinets only.)
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinets
96” Countertop. Covers over 4 Cabinets
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools.
• See “Parts” and “Tools Needed” in the list below.
Parts
Supplied
Threaded Caps
Threaded Washer
Handles
Handle Bolts ( M4 x 22mm)
#8 x 25mm Screws
Lag Screw ( 6 mm x 55 mm)
Glass Shelves
Shelf Pins
Tall Wall Display
Cabinet
4
4
2
4
4
4
3
14
Glass Shelves Shelf Pins
Handle Screws
#8 x 25mm
Handle Bolt
M4 x 22mm
Lag Screw
6mm x 55mm
Threaded
Washer
Threaded
Caps
Tools Needed
1 x #2 Phillips head
screwdriver
1 x #2 Phillips Bit
(opitional)
1 x Stud Finder 1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure
1 x
2.5mm or 3/32”
drill bit
1 x
6.5 mm or 1/4”
drill bit
1 x Flashlight
(optional)
Installing the Handles
1 Parts Needed.
2
Note:
Cabinets come with handles installed on inside of drawers/doors.
Align handle to holes on doors or drawers.
2 x Handle 2 x Handle Bolt
M4 x 22mm
3 Screw in bolts.
Inserting Glass Shelves
1 Open cabinet doors. Attach shelf clips to desired height.
2 Ensure clips are at level height.
3 Insert glass shelf at a slight angle.
4 Position over shelf supports .
5
Lower shelf down onto shelf supports.
6 Repeat steps 1-4 for all shelves.
Mounting Cabinets
7 Use stud finder to locate the studs and mark the wall with a pencil.
8
Gather parts.
4 x Lag Screw
6mm x 55mm
4 x Threaded
Washer
4 x Threaded
Caps
9 Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs. Repeat for drilling two holes near the bottom of the cabinet.
Pilot Holes
10 Place cabinet flush against wall and attach using screws and washers.
11 Use threaded caps to cover screws.
Fastening Cabinets
12 Parts Needed.
13
Note:
All shelves must be removed prior to fastening cabinets together.
Drill 3/32” pilot holes on interior wall of cabinet being fastened.
4 - #8 x25mm screws
14 Using pilot hole as guides, screw into second cabinet.
Do Not Over-tighten screws and Punch through other side!
Adjusting The Door Hinges
Using a Philips screwdriver, the doors can be adjusted:
Left, right, forwards and backwards.
15 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.
A
16
To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
B
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
HOME BAR SERIES
WALL WINE RACK
Warning: Excessive weight hazard!
Use two or more people to move, assemble or install cabinets to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Weight
Capacity
50 lbs.
50 lbs.
50 lbs.
Wall
Wine Rack
Max 150 lbs.
Countertops
(for Base cabinets only.)
48” Countertop. Fits over 2 Cabinets
72” Countertop. Fits over 3 Cabinet
96” Countertop. Covers over 4 Cabinet
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Parts Supplied
Threaded Caps
Wall Rack Cabinet
4
Threaded Washer
Handles
4
2
Handle Bolts ( M4 x 22mm) 4
#8 x 25mm Screws
Lag Screw ( 6 mm x 55 mm)
4
4
Handles
Handle Bolts
M4 x 22 mm Lag Screw
6 mm x 55 mm
#8 x 25 mm
Screws
Tools Needed
Threaded
Washer
Threaded Cap
1 x #2 Phillips head
screwdriver
1 x #2 Phillips Bit
(opitional)
1 x Stud Finder 1 x Cordless Power Drill
(optional)
1 x Pencil 1 x Tape Measure
1 x
2.5mm or 3/32”
drill bit
1 x
6.5 mm or 1/4”
drill bit
1 x Flashlight
(optional)
Installing the Handles
1 Parts Needed.
Note:
Cabinets come with handles installed on inside of drawers/doors.
2 Align handle to holes on doors or drawers.
2 x Handle 4 x Handle Bolt
M4 x 22mm
3
Screw in M4 x 22mm bolts.
Mounting Cabinets
7 Use stud finder to locate the studs and mark the wall with a pencil.
8
Gather parts.
4 x Lag Screw
6mm x 55mm
4 x Threaded
Washer
4 x Threaded
Caps
9 Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs. Repeat for drilling two holes near the bottom of the cabinet.
Pilot Holes
10 Place cabinet flush against wall and attach using screws and washers.
11 Use threaded caps to cover screws.
Fastening Cabinets
4 Parts Needed.
5
Note:
Remove wine rack to make attaching cabinets easier.
Drill 3/32” pilot holes on interior wall of cabinet being fastened.
4 - #8 x 25mm screws
6 Using pilot hole as guides, screw into second cabinet.
Do Not Over-tighten screws and Punch through other side!
Adjusting The Door Hinges
Using a Philips screwdriver, the doors can be adjusted:
Left, right, forwards and backwards.
12 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.
A
13
To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
B
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
Manufacturer One Year Limited Warranty
When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for a period of One Year from the purchase date of the product.
NEWAGE PRODUCTS INC. WILL NOT PAY FOR:
1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.
2. Damage resulting from products damaged by accident, misuse, abuse, fire, flood, improper installatinion, acts of God, neglect, modification or mishandling.
3. Products damaged by improperly loading beyond the specified maximum weight capacity outlined in the instrutions provided with the product.
4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commerical environment, or handled in anyway inconsistent with the installation instructions included with the product.
5. Surfaces damaged due to chemcal interaction.
6. Replacement parts for NewAge products outside Canada,The United States, or the UK.
7. Loss of product contents due to theft, fire, flood, accident or acts of God.
8. Shipping or freight fees to deliver replacement products or to return defective products.
9. Any labor costs during the limited warranty period.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD
ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW
LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project