advertisement
Route cords along articulating arms using cord management clip s.
Articulating arms can be adjusted to position display into desired location.
Use wrench(8) to tighten and loosen the tension screw. Do not overtighten or overloosen to make the screws come out.
±180 °
±180 °
±180 °
-5 15
±5°
Wrench 4x4
-8-
P yle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
Warning
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children !
1.Make sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, contact a professional installer for assistance.
2.The wall or mounting surface must be capable of supporting the combined weight of the mount and the display; otherwise the structure must be reinforced
.
3.Safety gear and proper tools must be used. A minimum of two people are required for this installation. Failure to use safety gear can result in property damage, serious injury or death.
INSTALLATION GUIDE
Item No.: PSWLE81
TV Size Range: 26 42
Maximum Weight Capacity: 25kg/55lbs
VESA: 400X400
Safety automatic lock
Unlock cord
CAUTION
This product was designed to be installed on wood stud walls and solid concrete walls.
Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Never exceed the Maximum Load Capacity. This product is intended for indoor use only. Use of this product outdoors could lead to product failure or ventilation on some screens. Please refer to the manufacturer’s requirements for mounting your screen befourinstallation.
-2-
1
5
7
6
4
2
Magnetic removable bubble level
A-D E F
3
G H
8
3
4
5
ID
1
2
6
7
8
Qty
1
2
2
1
2
2
2
1
Description
Wall plate
Bracket
Ribbon
TV plate
Plastic cover
Screw
Slide block(Position lock)
Wrench(4x4)
ID
A
B
C
D
E
F
G
H
3
3
3
Qty
4
4
4
4
4
Description
M4 ×16 mm bolt
M5 ×16 mm bolt
M6× 16 mm bolt
M8×16mm bolt
Square washer
Long bolt washer
Long bolt
Wall anchor
Hook the top of brackets (2) onto the top flange of wall plate(1). Then swing the screen down. Fixed slide block into wall plate by screw.
Always use an assistant or mechanical lifting equipment to safely lift and position heavy equipment.
2
7 6
FIG.A
Before installation, please attach these two decorative end caps to the two sides of TV plate.(FIG.A)
-7-
-6-
Center brackets vertically on back of screen. Select the small(A),medium
(B or C) or large(D) screws.
Attach brackets to screen using four selected screws and four square washers(E) at the top and bottom of each bracket.
Tighten screws firmly. Do not overtighten .
Square washer(E)
Large hole for
M8 screws
Medium hole for
M5 and M6 screws
Small hole for
M4 screws
E
A-D
Use wall plate(1) as a template, make sure it is level, and mark mounting holes on the wood studs. Drill three 3/16 ” three
.
.
50mm
Stud finder
Wood stud
F
G
Magnetic removable bubble level
-3-
Level wall plate and use wall as a template to mark three holes. Drill three and secure wall plate with three long bolts(G) and three washers(F).Tighten
screws firmly. Do not overtighten
.
58mm
Secure plastic covers over wall plate by pushing them toward each other until they lock in place.
5
-4-
Concrete Wall
H
F
G
Magnetic removable bubble level
If you think the ribbon is too long, You can hide it at the back of the televesion,once you want to uninstall the TV, it can help you to take out the brackets .
3
-5-
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project