Lutron PJ2-3BRL-GWH-L01 Installation Instructions

Lutron PJ2-3BRL-GWH-L01 Installation Instructions
Pico® Wireless
Control
Set-Up (for Maestro WirelessR systems only)
3 V- 10 mA
To communicate with other systems or devices, including
Radio RAR 2, QS sensor module (QSM), QuantumR, HomeworksR QS,
Serena Shades, and SivoiaR QS, refer to the system setup guides.
See www.lutron.com/pico for more information.
Mounting
accessories
sold separately.
For a complete
listing of PicoR
wireless mounting
accessories,
please visit
www.lutron.com/pico
PJ2-2B
PJ2-2BRL PJ2-3B
Operation
English
PJ2-3BRL
Please Read Before Installing
1. This install guide provides simple setup instructions for Maestro
WirelessR systems only. If you are using your PicoR wireless
control with any other LutronR system, please refer to the system
setup guide. If you no longer have your system setup guide,
please download the latest version by following the links at
www.lutron.com/pico
2. The PicoR wireless control uses one (1) CR2032 battery (pre-installed).
DO NOT use rechargeable batteries. Using improper batteries could
damage the PicoR wireless control. DO NOT dispose of the battery
in normal household waste. Please recycle, take to a proper battery
disposal facility, or contact your local waste disposal provider regarding
local restrictions on the disposal or recycling of batteries.
1. Press and hold the dimmer/switch tap button (Figure 1) for
approximately 6 seconds. Once the LED(s) start to blink slowly,
release the tap button.
2. Press and hold the OFF button on the PicoR wireless controller
(Figure 2) for approximately 6 seconds.
Un-pairing a PicoR Wireless Control
5. Pressing the Preset button (3B and 3BRL models only) on a PicoR
wireless control will cause all dimmers to go to the favorite light
settings. Switches can be configured to turn ON or OFF. To save a
favorite light setting, adjust all the dimmers/switches controlled by
a PicoR wireless control to the desired light setting. Then press and
hold the Preset button on the PicoR wireless control for 6 seconds
until all LEDs on the dimmers/switches flash several times.
To un-pair a previously paired PicoR wireless control from your system,
tap the OFF button (Figure 2) on the PicoR wireless control three
times, on the third tap hold for 6 seconds and then tap three more
times. This will remove all dimmers/switches it was previously paired
with.
1. Place a flathead screwdriver into
the slot at the bottom of the PicoR
wireless control. Twist to open.
DO NOT press buttons without
back enclosure on.
2. Slide the battery out, toward the top
of the PicoR wireless control.
3. Slide a new battery underneath the
contact strap, with the (-) terminal
toward the front of the PicoR wireless
control.
Raise Button (2BRL & 3BRL models only)
Lights increase in intensity; shades/draperies move toward
open limit.
Preset Button (3B & 3BRL models only)
Tap Once: Devices go to preset levels.
Press and Hold: To save new preset level, press and
hold for 6 seconds.
Lower Button (2BRL & 3BRL models only)
Lights decrease in intensity; shades/draperies move toward
close limit.
Technical Assistance
Figure 1
Figure 2
For questions concerning the installation or operation of this product, call
the Lutron Technical Support Center. Please provide exact model number
when calling.
TEL +1.610.282.3800
FAX +1.610.282.1243
Toll Free 1.888.LUTRON1
USA, Canada, Caribbean 1.800.523.9466
Mexico +1.888.235.2910
Central/South America +1.610.282.6701
European Headquarters
Asian Headquarters
United Kingdom
Lutron EA Ltd.
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical Support: +44.
(0)20.7680.4481
Freephone: 0800.282.107
www.lutron.com/europe
Singapore
TEL +65.6220.4666
FAX +65.6220.4333
Asia Technical Hotlines
Northern China 10.800.712.1536
Southern China 10.800.120.1536
Hong Kong 800.901.849
India +91.11.4051.4300
Indonesia 001.803.011.3994
Japan +81.3.5575.8411
Macau 0800.401
Singapore 800.120.4491
Taiwan 00.801.137.737
Thailand 001.800.120.665853
Other countries +65.6220.4666
5. Confirm proper installation by turning the receiving device on and off
using the PicoR wireless control.
Wireless Control of Multiple Switches
) Geometry of the building structure
) Construction of walls separating system components
) Electrical equipment located near system components
6. Clean PicoR wireless control with a soft damp cloth only.
DO NOT use any chemical cleaners.
7. DO NOT paint the PicoR wireless controller.
8. DO NOT mount the PicoR wireless controller to a metal surface.
If multiple wireless dimmers/switches are paired with the same PicoR
wireless control, they will perform as follows:
) Pressing the ON button on the PicoR wireless control will cause all
dimmers/switches to turn ON fully.
) Pressing the OFF button on the PicoR wireless control will cause all
dimmers/switches to turn OFF completely.
) Pressing the Raise button (2BRL and 3BRL models only) on a PicoR
wireless control will cause all dimmers to turn ON and gradually increase
in intensity.
) Pressing the Lower button (2BRL and 3BRL models only) on a PicoR
wireless control will cause all dimmers to gradually decrease in intensity.
The dimmers will not turn off and will remain at low end.
) Pressing the Preset button (3B and 3BRL models only) on a PicoR
wireless control will cause all dimmers to return to the favorite light
settings. Switches can be configured to go to ON or OFF.
(See Step 5 in Set-Up)
P/N 040400 Rev. A 09/2013
www.lutron.com
World Headquarters
4. Replace the back enclosure.
4. Up to 10 PicoR wireless controls can be configured to work together in
a Maestro WirelessR system.
Lutron Electronics Co., Inc.
7200 Suter Road Coopersburg, PA 18036-1299
(for Maestro WirelessR systems only)
Replacing the Battery in a PicoR Wireless Controller
3. The PicoR wireless control must be paired with dimmer(s) /switch(es)
before it can communicate.
) Distance between system components
OFF Button
Lights dim to off; shades/draperies go to close limit.
4. Repeat steps 1 to 3 to pair multiple PicoR wireless controls with a
single dimmer / switch. Repeat steps 1 to 3 to pair a single PicoR
wireless control with multiple dimmers / switches.
Warning: Risk of fire, explosion and burns. May result in
serious injury or death. DO NOT recharge, disassemble,
crush, puncture, heat above 212 °F (100 °C) or incinerate the
battery. The battery in this device contains Perchlorate
Material - special handling may apply. For more information
visit www.dtsc.ca.gov/hazardouswaste/perchlorate
5. The range of the PicoR wireless control is 30 ft (9 m). Performance is
highly dependent on a variety of complex factors such as:
ON Button
Lights brighten to full intensity;
shades / draperies go to open limit.
Important: Set up a PicoR wireless control to a dimmer / switch
before use.
3. Once the dimmer/switch pairs with the PicoR wireless control, the
LED(s) on the dimmer/switch and the load will flash 3 times and it will
exit Set-Up mode.
Important Notes
Indicator LED
Flashes to indicate a button press or
when unit is in programming mode.
Troubleshooting
Symptoms
Possible Causes
Light does not
respond to PicoR
wireless controller
• The dimmer/switch failed to pair with PicoR wireless control; see Set-Up.
• The dimmer/switch has already received and responded to a command or is already at the light setting the PicoR
wireless control is sending.
• The PicoR wireless control is outside the 30 ft (9 m) operating range.
• The battery in the PicoR wireless control is low.
• The battery in the PicoR wireless control is installed incorrectly.
When in set-up mode
the LEDs on the
dimmer/switch flash
when trying to setup
with the PicoR wireless
controller or sensor.
• The maximum number of PicoR wireless controls or sensors have been paired with the dimmer/switch. More PicoR
wireless controls or sensors can not be added. See Un-pairing a PicoR Wireless Control.
Lutron, ), Pico, RadioRA, Quantum, HomeWorks, Sivoia, and Maestro Wireless are registered trademarks and RadioRA 2 is a trademark of Lutron Electronics Co., Inc.
© 2013 Lutron Electronics Co., Inc.
®
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising