Radio Shack 900MHz User's Manual

Radio Shack 900MHz User's Manual
2-Line 900MHz Cordless
Answering Machine
Please read before using this equipment.
Owner’s Manual
with Speakerphone
This telephone has been tested and found to comply with all applicable UL and FCC
standards.
WARNING: To reduce the risk of fire
or shock hazard, do not expose this
product to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsulated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to constitute a risk of electric shock. Do
not open the product’s case.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
© 2000 Tandy Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by Tandy Corporation.
2
ˆ Contents
Contents .................................................................................................................. 3
Features ................................................................................................................... 5
Read This Before Installation ............................................................................. 7
Important Safety Instructions .............................................................................. 7
A Quick Look At Your Telephone ........................................................................ 10
Installation .............................................................................................................
Mounting the Phone .........................................................................................
Connecting to Phone Lines ........................................................................
On a Desk Top ...........................................................................................
On a Wall Plate or a Wall ...........................................................................
Connecting and Charging the Battery Pack .....................................................
Setting the Dialing Mode ..................................................................................
Adjusting the Ringer .........................................................................................
On the Handset ..........................................................................................
On the Base ...............................................................................................
Setting the Number of Rings ............................................................................
Setting the Day/Time ........................................................................................
10
10
11
11
12
13
14
14
14
14
15
15
Basic Operation ....................................................................................................
Making a Call ....................................................................................................
Answering a Call ..............................................................................................
Setting the Handset Volume .............................................................................
Adjusting the Speakerphone Volume ...............................................................
Using Mute .......................................................................................................
Using HOLD .....................................................................................................
Switching Between the Handset and Speakerphone .......................................
Using Both the Handset and Speakerphone ....................................................
Making a Conference Call ................................................................................
3-Way Conferencing ..................................................................................
4-Way Conferencing ..................................................................................
Using the Phone with Extension Phones .........................................................
Using REDIAL ..................................................................................................
Using FLASH ....................................................................................................
Using Tone Services On a Pulse Line ..............................................................
Using the Paging/Intercom Features ................................................................
Using a Headset ...............................................................................................
15
15
16
16
16
16
17
17
17
17
17
18
18
18
18
19
19
20
Contents
3
Memory Operation ................................................................................................
Storing a Number in Memory ............................................................................
Entering a Pause .......................................................................................
Dialing a Memory Number ................................................................................
Chain-Dialing Service Numbers .................................................................
Testing Stored Emergency Numbers .........................................................
20
20
21
21
21
21
TAD Operation .......................................................................................................
Selecting the Outgoing Message ......................................................................
Recording/Deleting an Outgoing Message .......................................................
Setting the Record Time ...................................................................................
Setting the Phone to Answer Calls ...................................................................
Screening Calls ................................................................................................
Recording Incoming Messages ........................................................................
Recording a Memo ...........................................................................................
Recording a Conversation ................................................................................
Playing Messages ............................................................................................
Adjusting the TAD’s Volume .............................................................................
Deleting Messages ...........................................................................................
Setting the Remote Operation PIN ...................................................................
22
22
22
22
23
23
23
24
24
24
25
25
25
Remote Operation ................................................................................................. 26
Using the Toll-Saver ......................................................................................... 26
Using Remote Commands ............................................................................... 26
Troubleshooting .................................................................................................... 28
Care ........................................................................................................................
Replacing the Battery Pack ..............................................................................
The FCC Wants You to Know ...........................................................................
Lightning ...........................................................................................................
4
Contents
29
30
31
31
ˆ Features
Your RadioShack 2-Line 900MHz Cordless Answering Machine uses advanced
cordless telephone technology to give
you extended range and superior audio
quality, with less interference than many
other cordless phones. The phone lets
you make and receive calls on two separate telephone lines.
The answering system stores up to 25
minutes or up to 59 messages on a
computer chip and records each message’s day and time. This gives you advanced capabilities over tape-based
answering machines:
• you can delete individual messages
and save the rest.
• there are no tapes to bother with
and no tape mechanisms to wear
out.
The remote operation feature lets you
operate your TAD from a touch-tone
phone (or from a rotary phone with a
pocket tone dialer).
Its features include:
Headset Jack — lets you make or answer calls with handsfree convenience
using an optional headset.
10-Number Memory Dialing — lets you
store up to 10 numbers in memory for
easy dialing.
Ample Talk and Standby Time — the
supplied battery pack provides 7 hours
of continuous talk time or 7 days of
standby time (when fully charged).
Paging/Two-Way Intercom System —
lets you send a signal from the base to
the handset, or from the handset to the
base, to page someone or locate the
handset when it is away from the base.
If someone answers, you can use the
phone as an intercom.
Dual Volume Controls — let you adjust
the volume you hear through the handset and speakerphone.
Adjustable Ringer — lets you choose
high or low volume for both lines’ ringers.
Wall Mountable — you can mount the
phone on the wall to save space on your
desk top.
TELEPHONE FEATURES
Two-Line Telephone System — lets
you easily handle two telephone lines at
the same time. You can use both lines to
make 3- or 4-way conference calls, or
use one line for data communication
while you are talking on the other.
Speakerphone — lets you answer calls
without using the handset.
Facedown or Faceup Handset Charging — you can place the handset on the
base facedown or faceup.
40 Channels — automatically selects a
clear channel when you make or answer
a call.
Security Access-Protection Code —
automatically prevents other cordless
Features
5
phone users from using your phone line
while the handset is off the base.
Line Status Indicators — show if a line
is available, in use, or on hold.
Redial — lets you quickly redial the last
number dialed.
Flash — sends an electronic switchhook signal for use with special phone
services, such as Call Waiting.
Tone/Pulse Dialing — lets you use your
phone with either type of service, and
you can easily switch from pulse to tone
dialing for long-distance, bank-byphone, or other special services.
Hearing-Aid Compatibility — lets you
use your phone with hearing aids that
have a T (telephone) switch.
TAD FEATURES
Call Screening — lets you listen as a
caller leaves a message so you can decide whether or not to answer the call.
Day/Time Stamp — records the day
and time each message was recorded.
Two-Line System — records incoming
messages separately for Line 1 and Line
2.
Two Prerecorded Messages — gives
you the option of using one of two prerecorded outgoing messages or recording your own.
Announcement Only — lets you play
an announcement for callers to hear,
without recording their messages.
Message-Counter — shows the number of messages the TAD has recorded.
Programmable PIN — you can set a
two-digit personal identification number
(PIN) for secure remote operation.
Memo Recording — lets you leave
messages for yourself or others in your
home or office. You can also record your
phone conversation.
Important: Every state has different regulations governing the recording of conversations over the telephone. Be sure
to check your local, state and federal
laws before using this product to record
any telephone conversation in order to
determine that your use is in compliance
with such laws or guidelines.
Phone Pick-Up Detection — stops recording when you pick up any phone on
the same line as the phone, and resets
to answer the next call.
Adjustable Ring Number — lets you
set the TAD to answer after three or five
rings, or use Toll Saver to avoid unnecessary charges when you call by long
distance to check your messages.
Digital Volume Control — lets you precisely adjust the speakerphone and
message playback.
Important:
Adjustable Incoming Message Recording Time — lets you set the TAD to
record one minute or four minutes. You
can set for each line separately.
6
Features
• Cordless phones such as this one
require AC power to operate. When
the AC power is off, you cannot dial
out or receive incoming calls using
your phone. To be safe, you should
• coin-operated systems
also have a corded phone that does
not need AC power to operate so
you can still make and receive calls
if there is an AC power failure.
• When AC power is lost, the phone
loses the security access-protection
code connection between the base
and the handset. When power is
restored, put the handset on the
base briefly to restore this connection so you can use the handset.
READ THIS BEFORE
INSTALLATION
We have designed your telephone to
conform to federal regulations, and you
can connect it to most telephone lines.
However, each telephone (and each device, such as an answering machine)
that you connect to the telephone line
draws power from the telephone line.
We refer to this power draw as the device’s ringer equivalence number, or
REN. The REN is on the bottom of your
telephone.
If you use more than one phone or other
device on the line, add up all of the
RENs. If the total is more than five (or
three in rural areas), your telephones
might not ring. If ringer operation is impaired, remove a device from the line.
Your telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and the REN to your telephone company. Both numbers are on the bottom of
your telephone.
Note: You must not connect your telephone to:
• party-line systems
• most electronic key telephone systems
This equipment complies with the limits
for a Class B digital device as specified
in Part 15 of FCC Rules. These limits
provide reasonable protection against
radio and TV interference in a residential
area. However, your equipment might
cause TV or radio interference even
when it is operating properly. To eliminate interference, you can try one or
more of the following corrective measures:
• reorient or relocate the receiving
antenna
• increase the distance between the
equipment and the radio or TV
• use outlets on different electrical circuits for the equipment and the
radio or TV
Consult your local RadioShack store if
the problem still exists.
You must use shielded interface cables
with this equipment.
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment,
basic safety precautions should always
be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
1. Read and understand all instructions.
Features
7
near or over a radiator or heat register. This product should not be
placed in a built-in installation
unless proper ventilation is provided.
2. Follow all warnings and instructions
marked on the product.
3. Never install telephone wiring during
a lightning storm.
4. Never install telephone jacks in wet
locations unless the jack is specifically designed for wet locations.
5. Never touch uninstalled telephone
wires or terminals unless the telephone line has been disconnected
at the network interface.
6. Use caution when installing or modifying telephone lines.
7. Do not fix the AC power supply cord
to building surfaces with metal fittings (if the product has an AC
power cord).
8. Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
9. Do not use this product near water,
for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, causing serious
damage to the product.
11. Slots and openings in the cabinet
and the back or bottom are provided
for ventilation. To protect it from
overheating, these openings must
not be blocked or covered. The
openings should never be blocked
by placing the product on a bed,
sofa, rug, or other similar surface.
This product should never be placed
8
12. This product should be operated
only from the type of power source
indicated on the marking label. If
you are not sure of the type of
power supply to your home, consult
your local power company.
13. Do not allow anything to rest on the
power cord. Do not locate this product where the cord will be stepped
on.
14. Do not overload wall outlets and
extension cords as this can result in
a risk of fire or electric shock.
15. Never push objects of any kind into
this product through cabinet slots as
they may touch dangerous voltage
points or short out parts that could
result in a risk of fire or electric
shock. Never spill liquid of any kind
on the product.
16. To reduce the risk of electric shock,
do not disassemble this product.
Take it to a qualified service technician when service or repair work is
required. Opening or removing covers may expose you to dangerous
voltage or other risks. Incorrect
reassemble can cause electric
shock when the product is subsequently used.
17. Unplug this product from the wall
outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power cord plug is damaged or frayed.
Features
sive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
B. If liquid has been spilled, into the
product.
C. If the product has been exposed to
rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions
because improper adjustment of other
controls may result in damage and will
often require extensive work by a qualified technician to restore the product to
normal operation.
E. If the product has been dropped or
the cabinet has been damaged.
F. If the product exhibits a distinct
change in performance.
4. Exercise care in handling the battery
pack in order not to short it with conducting materials such as rings,
bracelets, and keys. The battery or
conductor may overheat and cause
burns.
5. Charge the battery pack provided or
identified for use with this product
only in accordance with the instructions and limitations specified in the
instruction manual provided for this
product.
6. Observe proper polarity orientation
between the battery pack and battery charger.
SAVE THESE INSTRUCTIONS
18. Avoid using a telephone (other than
a cordless type) during an electrical
storm. There may be a remote risk
of electric shock from lightning.
19. Do not use the telephone to report a
gas leak in the vicinity of the leak.
CAUTION: TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the appropriate type and
size battery pack specified in the
instruction manual provided for this
product.
2. Do not dispose of the battery pack in
a fire. The cell may explode. Check
with local codes for possible special
disposal instructions.
3. Do not open or mutilate the battery
pack. Released electrolyte is corroFeatures
9
ˆ A Quick Look At Your Telephone
MEM
MUTE
HOLD
LINE 2
LINE 1
CONFERENCE
LINE 1
MSG LINE
SELECT
INTCM
VOLUME
CH
DELETE
CONF
REDIAL
REPEAT
FLASH
HOLD
ANSWER
LINE 2
SKIP
PIN
OGM
MEMO
VOLUME
PLAY/STOP
CLOCK
INTERCOM
ˆ Installation
MOUNTING THE PHONE
You can place the phone’s base on a desk or table, or mount it on a standard wall
plate or directly on a wall. Choose a location that is:
• near an accessible AC outlet
• near a modular telephone jack
10
A Quick Look At Your Telephone
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
• away from other cordless phones
The base’s location affects the handset’s range. If you have a choice of several locations, try each to see which
provides the best performance.
Caution: The supplied AC adapter was
designed specifically for your phone.
Use only the supplied adapter.
Connecting to Phone Lines
To take full advantage of the phone’s
capabilities, you must have two phone
lines with separate phone numbers. If
you have only one line, you can order a
second line from your phone company.
• The line that connects a two-line
phone jack to the phone company
wiring must be twisted-pair cable.
Otherwise, you might hear interference (crosstalk) between the two
lines.
• The USOC number of the two-line
jack to be installed is RJ14C
(RJ14W for a wall plate). The USOC
number of a single-line jack is
RJ11C.
On a Desk Top
1. To connect the phone to a two-line
phone jack, plug one end of the supplied long two-line modular cord into
TEL LINE 1/2 on the back of the
phone.
TEL LINE 1/2
You can connect the phone to the lines
in one of these ways:
• connect two lines through a two-line
modular phone jack
• connect two lines through two oneline modular phone jacks
• connect one line through a one-line
modular phone jack
Notes:
• Your phone connects directly to a
modular phone jack. If your phone
wiring does not have a modular
jack, you can update it using jacks
and adapters available at your local
RadioShack store. Or, you can have
the phone company update it for
you.
Installation
Note: If you connect the phone to a
two-line phone jack with a two-line
cord, do not connect another (third)
phone line to TEL LINE 2 or the
phone will not operate properly.
Instead, you can connect another
phone device, such as a fax
machine or modem.
To connect the phone to two oneline phone jacks, plug one end of
the supplied long two-line modular
cord into TEL LINE 1/2 and plug
another cord (not supplied) into TEL
LINE 2.
11
To connect the phone to a single
one-line phone jack, plug one end of
the supplied long modular cord into
TEL LINE 1/2 or TEL LINE 2.
Note: If you connect the phone to a
single one-line phone jack, avoid
pressing the unused line button or
you might hear feedback.
letting the heads extend about 5/16
inch from the wall.
2. Insert the two tabs at the top of the
wide end of the supplied bracket
into the base’s lower tab slots as
shown, then press down on the
bracket’s latches and insert them
into the clip slots.
2. Plug the supplied AC adapter’s barrel plug into DC IN 9V on the back of
the base.
DC IN 9V
3. Connect the phone line as
described in “On a Desk Top” on
Page 11.
3. Route the adapter’s cord through
the strain relief slot on the bottom of
the base.
4. Plug the adapter into a standard AC
outlet.
5. Connect the phone cord(s) to the
modular phone jack(s).
6. Raise the base’s antenna to a vertical position.
On a Wall Plate or a Wall
Note: To mount the base directly on the
wall, you need two screws (not supplied)
with heads that fit into the keyhole slots
on the bottom of the bracket.
4. Insert the supplied AC adapter’s
barrel plug into DC IN 9V on the back
of the base.
5. Route the adapter’s cord through
the narrow groove on the bracket. If
you are using two phone cords,
route the second cord through one
of the wide grooves on the bracket.
6. To mount the phone on a wall plate,
plug the other end of the short modular cord into the wall plate jack,
then align the bracket’s keyhole
slots with the wall plate studs and
slide the base downward to secure
it. If you are using two phone cords,
plug the second cord into the second phone jack.
1. Drill two holes 315/16 inches apart.
Then thread a screw into each hole,
12
Installation
To mount the phone directly on a
wall, align the bracket’s keyhole
slots with the mounted screws and
slide the base downward to secure
it. Connect the phone cord(s) to the
modular phone jack(s).
7. Plug the adapter into a standard AC
outlet.
8. Press and lift out the handset
holder, flip it over as shown, then
snap it back into place.
compartment. The connector fits
only one way.
3. Put the battery pack in the compartment.
4. Replace the cover.
To charge the battery pack, simply place
the handset on the base, facing either
up or down. The CHARGE indicator on
the base lights.
Important: Be sure the battery pack is
properly connected before you try to
charge it. The CHARGE indicator lights
when the handset is on the base, even if
the battery pack is not connected.
9. Raise the base’s antenna to a vertical position.
CONNECTING AND
CHARGING THE
BATTERY PACK
Your phone comes with a rechargeable
nickel-cadmium battery pack installed in
the handset, but not connected. Before
using your phone, you must connect the
battery pack, then charge it for about 24
hours.
1. Press down and slide off the battery
pack compartment cover.
2. Lift the battery pack out of the compartment. Plug the battery pack’s
connector into the socket in the
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear a five-beep error signal when you press LINE 1 or LINE 2.
If this happens, return the handset
to the base for about 5 seconds.
This resets the security accessprotection code.
• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a month.
• If the phone does not work, try
recharging the battery pack. (The
battery power might be too low to
flash the line indicators.)
• If the battery pack becomes weak
during a call, the handset beeps
every 3 seconds. When this happens, you cannot make another call
on the phone until you recharge the
battery pack.
Installation
13
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until the line
indicators flash. Otherwise, the battery pack loses its ability to fully
recharge.
If the dial tone stops, that line has
tone service. If the dial tone continues, that line has pulse service.
4. Press LINE 2, listen for the dial tone,
and repeat Step 3.
If you have tone service on both
lines, leave DIAL MODE set to T.
• If the battery pack is completely discharged or the base loses power
while the handset is away from it,
place the handset on the base to
reset the security access-protection
code. If it was the handset that lost
power, recharge the battery pack.
• The supplied battery pack should
last about one year. When it loses
its ability to fully recharge, order a
replacement battery pack through
your local RadioShack Store (see
Replacing the battery pack.
SETTING THE DIALING
MODE
ADJUSTING THE RINGER
The phone lets you control its base and
handset ringer volumes separately. You
can choose a high or low ringer setting
for the base or the handset.
On the Handset
Set DIAL MODE on the back of the base
for the type of service you have. If you
are not sure which type you have, do
this test.
1. Be sure DIAL MODE is set to T
(tone).
2. Press LINE 1 on the handset. Then
listen for the dial tone.
3. Press any number other than 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
14
If you have pulse service on either
line, set DIAL MODE to P (pulse).
You can use tone services on the
line which supports them by pressing ∗/TONE before any other keys.
At any time except during a call, repeatedly press VOLUME to change the ringer’s volume.
On the Base
Set RING VOL on the back of the base to
OFF, LO, or HI. With RING VOL set to
OFF, the base’s ringer does not sound
when a call is received, but the handset
when it is off the base (and any other
phone connected to the same line) still
rings.
Note: The RING VOL setting on the base
is common to both lines.
Installation
SETTING THE NUMBER
OF RINGS
Set RING TIME on the back of the base
to 3, 5, or TS (toll-saver) to select how
long the phone waits to answer a call (3
rings, 5 rings, or toll-saver).
Notes:
• If you plan to check messages by
long distance, set RING TIME to TS
(see “Using the Toll-Saver” on
Page 26).
• The ring time setting is common to
both lines.
SETTING THE DAY/TIME
You must set the day of the week and
time so the phone can record the correct
day and time of each message.
Notes:
• Enter each keypress within about 2
minutes. Otherwise, the phone exits
the time setting process and you
must begin again with Step 1.
• If a call is received during the setup
process, the phone exits the time
setting process. Begin again with
Step 1.
1. Hold down CLOCK until the phone
beeps. The phone announces the
currently set day and displays the
day’s number (0 for Sunday, 1 for
Monday, and so on).
2. To change the day of the week,
repeatedly press SKIP to move forward or REPEAT to move backward.
To set the correct day of the week
when it displays, press CLOCK.
3. The phone announces the hour. To
change the hour, repeatedly press
or hold down SKIP or REPEAT. To
set the correct hour when it displays, press CLOCK.
4. The phone announces the minutes.
To change the minutes, repeatedly
press or hold down SKIP or REPEAT.
To set the correct minutes when
they display, press CLOCK.
5. The phone announces “AM” or
“PM,” and A or P appears. Press
SKIP or REPEAT to change this setting. Press CLOCK again to set AM
or PM.
6. To check the day and time, press
CLOCK. The phone announces the
currently set day and time.
Note: When power fails, the clock retains the current time. When the power
is restored, it starts counting again from
the time the power failed.
ˆ Basic Operation
MAKING A CALL
To make a call, lift the handset from the
base and press LINE 1 or LINE 2, then
dial the number. When you press a line
button on the handset, the LINE 1 or
LINE 2 indicator on the handset lights.
The LINE 1 or LINE 2 indicator on the
base flashes to show that someone is
using that line at the handset.
Basic Operation
15
Note: If the LINE 1 or LINE 2 indicator
flashes, someone is using that line at
the base or on an extension phone.
Press the other line button.
To end a call, press LINE 1 or LINE 2 on
the handset or place the handset on the
base.
ANSWERING A CALL
When a call comes in, the line indicator
for that line flashes.
Note: To help you tell which line is ringing, each line has a distinctive ring tone.
To answer a call using the handset, lift
the handset from the base and press the
line button for the line that is ringing. If
the handset is away from the base,
press any key to answer a call.
To answer a call using the speakerphone, press either LINE 1 or LINE 2
(whichever is flashing). The indicator for
the line in use lights on the base. The indicator for the same line flashes on the
handset as a reminder that the line is in
use.
To end a speakerphone call, press LINE
1 (or LINE 2) again. The line indicator
turns off.
If you receive a call on one line while
talking on the other, you hear the base
ring and three ring tones through the
handset (or a low ring on the base when
using the speakerphone) if you have set
RING VOL to HI or LO. Press the line button for the incoming call’s line. The current call is automatically placed on hold.
16
If both lines have an incoming call,
pressing a key answers the line that began ringing first.
SETTING THE HANDSET
VOLUME
You can adjust the handset’s volume to
any of four settings (low, mid, high, maximum). To change the handset’s volume
during a call, repeatedly press VOLUME
on the handset. The setting remains the
same even when you hang up the
phone.
ADJUSTING THE
SPEAKERPHONE
VOLUME
To set the speakerphone’s volume,
press VOLUME ù or ø on the base.
The display shows the volume setting in
the range of 1 (lowest) to 10 (highest).
USING MUTE
While talking on the speakerphone, you
can temporarily turn off the phone’s microphone by pressing MUTE so the other
party cannot hear you. The indicator for
a muted line flashes red. Press MUTE
again to resume your conversation.
Hint: If the phone is close to loud noises
while you are using the speakerphone,
the phone might not switch to let you
hear the person on the other end of the
line. If this happens, press MUTE to turn
off the microphone so you can hear the
caller. Press MUTE again when it is your
turn to speak.
Basic Operation
USING HOLD
Press HOLD to place a call on hold. The
indicator for that line lights red on the
base. While a call is on hold, you can
temporarily place the handset on the
base or use the other phone line without
disconnecting the current call.
To release a line from hold and continue
your conversation, press that line’s button on the handset or base. You can
also release a call from hold by lifting the
handset if the handset is on the base, or
picking up an extension phone.
To release a line that was placed on
hold using another keypad (handset,
base, or an extension phone), press that
line’s button twice.
Note: Pressing HOLD again while a call
is on hold does not release the hold.
Press the line button that is on hold.
SWITCHING BETWEEN
THE HANDSET AND
SPEAKERPHONE
USING BOTH THE
HANDSET AND
SPEAKERPHONE
To use the handset to join a call at the
base, or to use the base to join a conversation at the handset, press the line
button for the line that is in use. You
hear a busy tone. Before the tone ends,
press the line button again.
During the call, one of you can hang up
and the call can continue. To end the
call, you must hang up both the base
and handset.
Note: If you hear a high-pitched noise
from the base’s speaker, the handset
and the base are too close together.
To talk with two parties using both lines,
see “4-Way Conferencing” on Page 18.
MAKING A CONFERENCE
CALL
3-Way Conferencing
To switch to the speakerphone while
you are using the handset, press HOLD
on the handset, then press LINE 1 or
LINE 2 on the base.
To switch to the handset while you are
using the speakerphone, lift the handset
off the base. Or, if the handset is off the
base, press HOLD on the base, then
press LINE 1 or LINE 2 on the handset.
Follow these steps to use both phone
lines to set up a 3-way call. The procedure is the same for the handset and the
base.
1. Place the first call on hold.
2. Answer a call on the other line.
3. Once you have the second party on
the line, press CONFERENCE (CONF
on the handset) to bring in the first
party. Both line indicators on the
base light green.
Basic Operation
17
4. To end the conference call, press
one line button, then the other. If you
want to hang up one line and continue talking on the other, press the
line button you want to hang up.
5. If you want to talk on one line without disconnecting the other, press
HOLD, then the button for the line
you want to talk on. To return to a 3way conversation, press CONFERENCE or CONF.
4-Way Conferencing
Follow these steps to use both lines and
the phone’s intercom function to set up a
four-way call (see “Using the Paging/Intercom Features” on Page 19).
1. Make a 3-way conference call. (See
“3-Way Conferencing” on Page 17).
2. Press INTCM on the handset or
INTERCOM on the base to page the
other keypad.
The two outside lines are automatically put on hold, but the parties on
both lines can talk with each other.
Note: You can also make a conference
call using both the phone and an extension phone (see “Using the Phone with
Extension Phones”).
USING THE PHONE WITH
EXTENSION PHONES
The phone detects when an extension
phone is in use, and the corresponding
line indicator flashes on the base.
To join the conversation from the handset or base, press the line button for the
line in use. You hear a busy tone. Before
the tone ends, press the line button
again.
Note: If you hang up the phone and
someone is still on that line on an extension, the phone’s line indicator(s) might
not stay lit.
USING REDIAL
You can quickly dial the last number dialed on either line. Press LINE 1 or LINE
2 then press REDIAL on the handset.
Notes:
3. To answer the page, press INTCM
on the handset or INTERCOM on the
base, then press CONF on the handset or CONFERENCE on the base.
• The redial memory is common to
both lines. You can redial the number you originally dialed on Line 1
using Line 2.
4. To end the conference call, press
LINE 1 then LINE 2 on one keypad,
then press LINE 2 on the other keypad.
• The redial memory holds up to 32
digits, so you can redial long distance as well as local numbers.
If you want to hang up one line and continue talking on the other, press the line
button that you want to hang up.
18
USING FLASH
FLASH performs the electronic equiva-
lent of a switchhook operation for special services, such as Call Waiting.
Basic Operation
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
the base flashes. Press INTCM on the
handset to answer the page. Both LINE
1 and LINE 2 indicators on the handset
stay lit and the CHARGE indicator on
the base stays lit.
Note: If you do not have any special services, pressing FLASH might disconnect
the current call.
To page the base from the handset,
press INTCM. The base and handset
ring, and the CHARGE indicator flashes.
Press INTERCOM on the base to answer
the page. Both LINE 1 and LINE 2 indicators on the handset stay lit and the
CHARGE indicator on the base stays lit.
USING TONE SERVICES
ON A PULSE LINE
Some special services, such as bankby-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following
these steps.
Note: The paging ends in one minute if
nobody answers. Press INTERCOM or
INTCM again.
To end an intercom call, press INTCM or
1. Be sure DIAL MODE is set to P.
INTERCOM.
2. Dial the service’s main number.
During a call, you can page someone at
either the base or the handset to join the
conversation. Press INTERCOM or INTCM. The current call is put on hold.
3. When the service answers, press ∗/
TONE. Any additional numbers you
dial are sent as tone signals.
4. After you complete the call, the
phone automatically resets to the
pulse mode when you hang up.
USING THE PAGING/
INTERCOM FEATURES
You can use the phone as a two-way
pager and intercom between the base
and the handset. This is useful if the
handset is away from the base and you
want to locate it, or if you want to have a
conversation between the handset and
the base.
To page the handset from the base,
press INTERCOM. The handset and
base ring, and the CHARGE indicator on
• To transfer the call, press INTERCOM or INTCM again when the person at the base or handset answers.
• To start a 3-way call, tell the person
at the base or handset to press the
line button for the call, then press
the same button twice on your keypad when they answer the page.
Notes:
• You cannot page the base or handset if it is already in use. A busy tone
sounds.
• If a call comes in during an intercom
conversation, either of the intercom
parties can answer the call as they
Basic Operation
19
normally would by pressing the ringing line’s button. The intercom call
automatically disconnects.
USING A HEADSET
Notes:
• Connecting a headset disconnects
the handset’s earpiece and microphone, but it does not affect the
phone’s speakerphone.
• VOLUME on the handset also controls the connected headset’s volume.
You can make or answer calls with
handsfree convenience using an optional headset (available at your local RadioShack store) that has a 3/32-inch (2.5
mm) plug.
To connect the headset, pull open the
rubber cover on the side of the handset,
then insert the 3/32-inch (2.5 mm) plug
into the jack.
• If you place the handset on the base
facedown to recharge it while the
headset is connected, be sure the
handset seats properly.
With a headset connected, you can
make or answer calls as usual, using the
keys on the handset.
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for greater convenience.
When you finish using the headset, disconnect it from the handset and close
the rubber cover to protect the jack.
ˆ Memory Operation
You can store up to 10 numbers in the
memory, then dial a stored number by
pressing a single digit memory location
number.
STORING A NUMBER IN
MEMORY
Notes:
• An error tone sounds and the phone
exits the storing process if you wait
more than 20 seconds between key
presses.
20
• Each number you store can be up to
16 digits long.
1. Lift the handset.
2. Press MEM. Both the line indicators
on the handset flash.
3. Enter the number and any tone or
pause entries (see “Using Tone Services On a Pulse Line” on Page 19
or “Entering a Pause” on Page 21).
Note: Each tone or pause entry
uses one digit of memory.
Memory Operation
4. Press MEM, then enter the memory
location number (0–9) where you
want to store the number. The tone
sounds to indicate that the number
is stored.
Note: If the phone sounds five quick
beeps, you have made an entry
error and the number was not
stored. Re-enter the location number correctly.
5. Repeat the steps to enter more
numbers.
To replace a stored number, simply
store a new one in its place. To erase a
number for a memory location, press
MEM twice. Then press the memory location number (0–9) you want to clear. A
tone sounds.
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect. For
each 2-second pause you want to enter,
press REDIAL.
DIALING A MEMORY
NUMBER
To dial a number stored in the memory,
lift the handset from the base and press
LINE 1 or LINE 2. Then press MEM and
the location number (0–9) by pressing a
number key. The phone automatically
dials the number.
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as alternate long distance or bank by phone), store each
group of numbers in its own memory location.
To use the stored special service numbers, dial the service’s main number
first. Then, at the appropriate place in
the call, press MEM and the number for
the memory location where the additional information is stored.
Testing Stored Emergency
Numbers
If you store an emergency service’s
number (police department, fire department, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to explain the reason for your call.
Memory Operation
21
ˆ TAD Operation
SELECTING THE
OUTGOING MESSAGE
RECORDING/DELETING
AN OUTGOING MESSAGE
The phone has two prerecorded outgoing messages. One asks the caller to
leave a message: “Hello, no one is available to take your call. Please leave a
message after the tone.” The phone
uses this message when REC TIME is
set to 1 or 4 (see “Setting the Record
Time”).
You can record different messages for
each line. Press MSG LINE SELECT so
the line indicator for the desired line
lights in the message counter window.
Hold down OGM until the phone beeps
and the message counter window starts
counting. Then speak your outgoing
message (up to 30 seconds long) into
the built-in microphone on the bottom of
the base. You can see how long your
message is by watching the message
counter window.
The other is simply an announcement
and does not let the caller leave a message: “Hello, no one is available to take
your call.” The phone uses this message
when REC TIME is set to ANN (announcement only).
When you finish your message, press
PLAY/STOP or OGM. The phone plays
back your message.
You can also record your own message
(see “Recording/Deleting an Outgoing
Message”). When you record your own
outgoing message, the phone uses it for
all REC TIME settings.
To switch between your outgoing message and the phone’s prerecorded message, repeatedly press MSG LINE
SELECT until the line indicator for the
desired line lights in the message
counter window, then press OGM. When
the current message begins to play,
press OGM again. The phone switches
to the other message and plays it. The
display shows P for prerecorded message or U for your own message.
To delete your outgoing message and
use the phone’s prerecorded messages,
hold down OGM until the phone beeps.
Then press OGM again within two seconds.
SETTING THE RECORD
TIME
Set REC TIME to 1, 4, or ANN to determine how the phone will record incoming messages for each line.
1 — The phone plays the outgoing message and lets callers leave a message
up to 1 minute long.
4 — The phone plays the outgoing message and lets callers leave a message
up to 4 minutes long.
22
TAD Operation
ANN (announcement only) — The phone
plays the outgoing message but does
not let callers leave a message.
SETTING THE PHONE TO
ANSWER CALLS
To set the phone to answer calls, repeatedly press MSG LINE SELECT until
the line indicator for the desired line
lights in the message counter window,
then press ANSWER. If the phone is set
to record a caller’s message (see “Setting the Record Time” on Page 22), it
plays the outgoing message and shows
the number of recorded messages. If the
phone is set to announcement-only, it
plays the outgoing message, and A appears.
Note: If the incoming message memory
is full, the phone announces, “No remaining time.”
To set the phone to not answer calls,
press MSG LINE SELECT so the line indicator for the desired line lights in the
message counter window, then press
ANSWER. The phone announces “Answer off” and the message counter turns
off.
Note: When you receive a call on one
line while you are using the speakerphone on the other line, the call screening function does not operate.
RECORDING INCOMING
MESSAGES
After the phone answers a call, it plays
the outgoing message, beeps, and
records the caller’s message.
Each incoming message can be up to 1
or 4 minutes long, depending on how
you set REC TIME (see “Setting the
Record Time” on Page 22). The phone’s
maximum recording capacity for both
lines is 25 minutes or 59 messages.
Note: When the phone receives a call
on one line while it is answering on the
other, it answers the new call after recording the first call.
The phone stops recording and resets to
answer the next call when:
• the caller hangs up
• the maximum message length is
reached
• the phone detects a busy signal or
more than 7 seconds of silence
SCREENING CALLS
You can let the phone answer calls for
you while you listen to the caller’s message through the base’s speaker. If you
decide to answer the call, press LINE 1
or LINE 2 on either the base or the handset to answer. You can also pick up any
phone on the same line. The phone
stops recording and resets to answer
the next call.
• you pick up the call on any phone on
the same phone line
Note: When the phone’s message
memory is full, FL appears on both
message counters and the phone announces “No remaining time” when you
try to operate it.
TAD Operation
23
RECORDING A MEMO
A memo is a message you can record at
the phone for yourself or others in your
home or office. The phone stores memos as incoming messages on the selected line (see “Playing Messages”).
To record a memo, press MSG LINE SELECT so the line indicator for the desired
line lights in the message counter window. Hold down MEMO on the base until
the phone beeps and starts counting in
the message counter window, then
speak your message. When you finish
the memo, press PLAY/STOP or MEMO.
Notes:
• The maximum length for recording a
memo is 10 minutes.
• The phone cannot record a memo
less than two seconds long.
• If you receive an incoming call or
page from the handset, the phone
exits the memo recording mode.
• You cannot record a memo while
the phone is answering the other
line.
RECORDING A
CONVERSATION
The phone lets you record both sides of
a telephone conversation.
Important Note: It is illegal in some areas to record a conversation without the
consent of all parties to the conversation, including the phone company.
Check the laws in your area before you
use the two-way recording feature.
24
To start recording a phone conversation,
repeatedly press MSG LINE SELECT until
the line indicator for the line you are talking on lights in the message counter
window. Then press MEMO on the base.
The phone beeps and the message
counter window starts counting. To stop
recording, press PLAY/STOP or MEMO.
The phone stores a recorded conversation as a message on the selected line
(see “Playing Messages”).
Notes:
• The maximum length for recording a
conversation is 10 minutes.
• The phone cannot record a conversation less than two seconds long.
• When you want to record a conference call using both LINE 1 and
LINE 2, you can select either line
with MSG LINE SELECT.
• You cannot record a conversation
when the telephone is answering on
the other line.
PLAYING MESSAGES
After the phone has recorded a message, its message counter shows the total number of messages stored. If you
have new messages, the number flashes.
To play your messages, repeatedly
press MSG LINE SELECT until the line indicator for the desired line lights in the
message counter window, then press
PLAY/STOP. The phone announces the
number of new and old messages, then
plays the new messages. The message
TAD Operation
number appears as each message
plays, and the phone announces the day
and time of the call at the end of each
message.
To play all messages after playing the
new messages, press PLAY/STOP again.
To skip to the next message, press SKIP
during playback. If you know the message number of the one you want to
hear, hold down SKIP until the desired
number appears.
To replay the current message from the
beginning, press REPEAT. If you press
REPEAT within about 2 seconds (4 seconds during remote operation) after a
message begins playing, the phone replays the previous message.
If you know the message number of the
one you want to hear, hold down REPEAT until the desired number appears.
ADJUSTING THE TAD’S
VOLUME
To adjust the speaker’s volume, repeatedly press VOLUME 8 or 9 on the
base. The volume setting from 1 (lowest) to 10 (highest) appears in the message counter window.
DELETING MESSAGES
To delete the current message while it is
playing, press DELETE. The phone
beeps.
To delete all messages on either line at
once, repeatedly press MSG LINE SELECT until the line indicator for the desired line lights in the message counter
window. Then, while messages are not
playing, hold down DELETE on the base
until the phone beeps and 0 appears in
the message counter window.
Note: You cannot delete new (unplayed)
messages. If you try to delete all messages at once while you still have new
messages, the phone sounds a long
beep and deletes old messages only.
SETTING THE REMOTE
OPERATION PIN
The phone’s two-digit remote operation
PIN (personal identification number)
prevents unauthorized remote access to
your messages. The PIN is preset to 80.
Follow these steps to change the PIN to
any number from 00 to 99. The PIN is
common to both lines.
Note: If you wait more than 2 minutes
between each keypress, the phone exits
the PIN setting process. Start again at
Step 1.
1. Hold down PIN until the phone
beeps and 00 appears in the message counter window.
2. Press SKIP to set the first digit of the
PIN higher or REPEAT to set it lower.
Then press PIN.
3. Press SKIP or REPEAT to set the
second digit of the PIN, then press
PIN. The phone announces the new
PIN.
4. To check your PIN at any time,
press PIN. The PIN appears in the
message counter window, and the
phone announces it.
TAD Operation
25
ˆ Remote Operation
While you are away from your home or
office, you can use a touch-tone phone,
or a pulse (rotary) phone with a pocket
tone dialer (available through your local
RadioShack store) to enter your PIN and
do any of the following:
• set the phone to answer or not
answer calls
USING REMOTE
COMMANDS
Follow these steps to operate the phone
from a remote location.
• listen to your messages
• record a new outgoing message
• erase messages
• monitor the room where the phone
is located
Notes:
• You cannot remotely operate the
phone using its handset or another
telephone on the same line as the
phone.
• You can also listen to the message
recorded on Line 2 by making a call
to Line 1’s number (or vice versa).
USING THE TOLL-SAVER
If RING TIME is set to TS (toll-saver),
(see “Setting the Number of Rings” on
Page 15), the phone answers after three
rings if you have new messages (ones
you have not listened to). If there are no
new messages, the phone answers after
five rings. This gives you time to hang
up before the phone answers so you
can avoid unnecessary long-distance
charges.
26
Note: Toll-saver works only on the line
you called. If Line 1 has no new messages, but Line 2 has one, the telephone answers after five rings when you
call Line 1.
Note: If you wait more than 15 seconds
between keypresses, the phone sounds
a long beep and hangs up.
1. Dial your phone number and wait for
the phone to answer.
2. If the phone is not set to answer
calls, it answers after about 10 rings
and sounds a series of beeps.
3. When the outgoing message begins
(or the phone sounds a series of
beeps), press #, then enter your PIN
within 2 seconds.
If the PIN is correct, the phone announces the day and time, then it announces
the number of new and old messages.
The phone plays all new messages,
then beeps about every two seconds to
let you know it is ready to accept remote
commands.
Notes:
• If the phone does not respond, try
entering your PIN again. If you enter
an incorrect PIN three times, the
phone beeps and hangs up.
Remote Operation
• When the phone is operating from a remote location, it stops all answering functions and rC appears on the display on the base. The phone resumes answering
functions when it is no longer in remote operation, if you have not turned it off.
• The remote playback of incoming messages is limited to 4 minutes. If you have
more messages after 4 minutes have passed, you must press # 2 again to listen
to the rest of the messages.
• When using remote operation, you can only delete the current message during
playback. You cannot delete all the messages stored at one time.
The following table shows the remote commands you can use.
Note: Remote operation stops when someone picks up the handset and presses either LINE 1 or LINE 2 (whichever is flashing), or any phone on the same phone line.
Remote Commands
Press #
then (within
2 seconds:
Function
1
Repeat current message during playback.
2
Play messages.
3
Skip current message during playback.
4
Delete current message during playback.
5
Stop playback, recording, and room monitoring.
6
Set the phone to answer or not answer calls.
7
Record or stop recording a new outgoing message.
8
Play the outgoing message.
9
Switch to the other line (Line 1 or Line 2).
0
Monitor the room where the phone is located for 15 seconds.
Remote Operation
27
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, the following suggestions might help.
Problem
The phone does not work or
works poorly.
Suggestion
• Be sure the base’s phone line cord and AC adapter are
correctly and securely connected.
• Be sure the handset’s battery pack is charged.
• Return the handset to the base for a few seconds to reset
the security-access protection code.
The handset stops working
or works poorly during a
call.
• Move the handset closer to the base.
• Lift the base’s antenna to a vertical position.
• Be sure the handset’s battery pack is charged.
Low volume or unusual
sounds.
• Someone has picked up another phone on the same line.
Hang up the other phone.
Severe noise interference.
• Keep the handset and base away from computers, remote
control toys, wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical
appliances.
• Move to another location or turn off the source of interference.
• Press CH to change the channel.
• Hang up and redial the number.
The phone cannot be operated at a useful distance
from the base because the
signal becomes weak or
noisy (handset’s range has
decreased).
• Lift the base’s antenna to a vertical position.
The handset battery pack
does not charge.
• Check the charging contacts on the handset and base. If
they are dirty, clean them with a pencil eraser.
• Be sure neither antenna is touching a metal surface.
• Recharge the battery pack.
• Be sure the handset is properly seated on the base.
• Replace the battery pack (see “Replacing the Battery
Pack” on Page 30).
28
Troubleshooting
Problem
Handset does not ring or
receive a page.
Suggestion
• Lift the base’s antenna to a vertical position.
• Move the handset closer to the base.
• Move the handset and base away from other electrical
devices.
• Recharge the battery pack.
The TAD does not answer
calls.
• Make sure the TAD is turned on.
• Make sure the AC adapter is properly connected.
• Check all phone line connections.
The TAD does not record
callers’ messages.
• REC TIME is set to ANN (announcement only). Set it to 1
or 4.
E E flashes.
• Microprocessor failure. Disconnect the AC adapter, wait 15
seconds, then plug in the adapter again.
• Delete message if memory is full.
If the base loses power while the handset is off of it, the security access-protection
code might change. Restore power to the base, then place the handset back on the
base and leave it there for a few seconds.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to your local RadioShack store for assistance.
ˆ Care
To enjoy your RadioShack 2-Line 900 MHz Cordless Answering System for a long
time:
• Keep the telephone dry. If it gets wet, wipe it dry immediately.
• Use and store the telephone only in normal temperature environments.
• Handle the telephone gently and carefully. Do not drop it.
• Keep the telephone away from dust and dirt.
• Wipe the telephone with a damp cloth occasionally to keep it looking new.
Care
29
Modifying or tampering with the telephone’s internal components can cause
a malfunction and might invalidate its
warranty and void your FCC authorization to operate it. If your telephone is not
performing as it should, take it to your local RadioShack store for assistance. If
the trouble is affecting the telephone
lines, the phone company can ask you
to disconnect your telephone until you
have resolved the problem.
3. Insert the new battery pack’s connector into the socket in the compartment, place the battery pack into
the compartment.
4. Replace the cover.
If you have trouble replacing the battery
pack, take the phone to your local RadioShack store for assistance.
Cautions:
REPLACING THE
BATTERY PACK
• You must use a replacement battery
of the same size and type.
If you follow the instructions in “Connecting and Charging the Battery Pack” on
Page 13, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a 600 mAh battery pack with a connector that fits the socket in the battery compartment. You can order a replacement
battery pack through your local RadioShack store.
• Do not dispose of the battery in a
fire because it might explode.
Install the new battery pack as described below, then charge it for about
24 hours (see “Connecting and Charging the Battery Pack” on Page 13).
Note: To avoid losing memory numbers,
install and begin charging the new battery pack within 2 minutes.
1. Press down and slide off the battery
pack compartment cover.
2. Lift the battery pack out of the compartment, then gently pull on the
battery connector to disconnect it.
30
• Do not open or mutilate the battery.
• Be careful not to short the battery by
touching the connector’s pins with
conducting materials, such as rings,
bracelets, and keys. The battery
pack or conductor might overheat
and burn.
Important: This telephone can use nickelcadmium rechargeable
batteries. At the end of a
nickel-cadmium battery’s
useful life, it must be recycled or disposed of properly. Contact
your local, county, or state hazardous
waste management authorities for information on recycling or disposal programs in your area or call 1-800-8437422. Some options that might be available are: municipal curbside collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling collection centers, and mail-back programs.
Care
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discontinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practical, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Also, the phone company can make
changes to its lines, equipment, operations, or procedures that could affect the
operation of this telephone. The telephone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interruption of your telephone service.
LIGHTNING
Your telephone has built-in protection
circuits to reduce the risk of damage
from surges in telephone line and power
line current. These protection circuits
meet or exceed the FCC requirements.
However, lightning striking the telephone or power lines can damage your
telephone.
Lightning damage is not common. Nevertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone when
storms approach to reduce the possibility of damage.
Care
31
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
12/99
43-681
UCZZ01266BZ
09A00
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement