Radio Shack U-120XR Owner's Manual
Add to my manuals4 Pages
Radio Shack U-120XR UHF Antenna: With this UHF Antenna, you can receive clear TV signals and enjoy your favorite channels. Installation is a breeze with the included hardware, and the antenna can be mounted on a mast or attached to an existing VHF antenna. You'll have access to a wide range of UHF broadcasts, including local news, weather, and entertainment. The durable construction ensures long-lasting performance, even in harsh weather conditions. Enhance your home entertainment experience with Radio Shack U-120XR UHF Antenna.
advertisement
15-2162a.fm Page 1 Thursday, April 27, 2000 2:21 PM
U-120XR UHF Antenna
BEFORE YOU BEGIN
Before you begin installation, read this manual and the separate Consumer Product Safety Commission information sheet.
For your safety and convenience, plan each step of the installation and purchase the necessary hardware in advance. The hardware required and the order in which you perform the steps depend on the mounting and connection method you choose.
Warning: When you install your antenna, use extreme caution.
If the antenna starts to fall, let it go! It could contact overhead power lines. If the antenna touches the power line, contact with the antenna, mast, cable, or guy wires can cause electrocution and death. Call the power company to remove the antenna.
Do not attempt to remove it yourself.
ASSEMBLING THE ANTENNA
Assemble the entire antenna on the ground.
1. Use the supplied hardware to loosely attach one of the supplied mast clamp assemblies to the main boom, as shown.
Note: To access the mast clamp holes, move the antenna’s elements out of the way as needed.
U-Bolt
Mast Clamp
Main Boom
Backup Plate
Lock Nuts
2. Attach the other mast clamp assembly to the cradle boom.
(Be sure it faces the same direction as the main boom’s mast clamp assembly, shown above.) Fold out the two sets of metal support straps on the cradle boom and attach them to the corresponding holes on the main boom using the two supplied 1 1 /
2
-inch screws and large wing nuts.
Cradle Boom
OWNER’S MANUAL — Please read before using this equipment.
3. Press the supplied large end plugs into the main boom and the cradle boom.
CONNECTING LEAD-IN CABLE
TO THE ANTENNA
We recommend RG-6 cable and, if you prepare your own cable, a quality F-connector. You can also use 300-ohm flat, twinlead cable. (RadioShack carries a variety of suitable cables and connectors.)
Note: If you prepare your own coaxial cable, be sure to slide the supplied matching transformer’s weather boot onto the cable before you attach the F-connector.
Using Coaxial Cable
Strain-Relief Tab
Main
Boom
F-Connector
Lead-In
Terminals
Flat Washers
Large
Wing Nuts
Spade
Terminals
Weather Boot
Matching
Transformer
If you plan to add this antenna to a VHF antenna’s mast, refer to “Adding the UHF Antenna to a VHF Antenna Installation” on
Page 2 for instructions. This type of setup requires twin-lead cable. See “Using Twin-Lead Cable” on Page 2 to connect the cable to your antenna. If you are connecting this UHF antenna directly to your TV, follow these steps to make this connection using coaxial cable.
1. Thread a matching transformer’s spade terminals through the antenna’s strain-relief tab. (Matching transformers are available at your local RadioShack store.)
2. Slide the spade terminals around the antenna’s lead-in terminals (on both sides of the boom), then secure them with the supplied flat washers and large wing nuts.
3. Screw the cable’s F-connector onto the matching transformer.
4. Slip the weather boot over the connection. If you use a rebuilt cable without a weather boot, cover the connection with weather-resistant tape.
Metal Support
Straps
Mast Clamp
Assemblies
Main Boom
© 2000 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
RadioShack.com is a trademark used by Tandy Corporation.
15-2162a.fm Page 2 Thursday, April 27, 2000 2:21 PM
Using Twin-Lead Cable
Main
Boom Twin-Lead Cable
5. Insert the top and bottom wing booms into the wing boom brackets. Secure them with the four supplied 1 1 /
4
-inch screws and small wing nuts, as shown.
Top Wing Boom
Wing Boom
Brackets
Lead-In Terminals
Flat Washers
Strain-Relief Tab
Large
Wing Nuts
To connect flat, twin-lead cable to your antenna:
1. Split one end of the twin-lead cable for a length of about 3 inches. Then strip about 1 /
2
inch of insulation from both leads.
2. Thread the stripped leads through the antenna’s strainrelief tab.
3. Wrap each lead around one of the antenna’s lead-in terminals (on both sides of the boom). Be sure there is enough slack between the strain-relief tab and the antenna terminals to prevent stress on the cable or the terminals.
4. Secure the leads with the supplied flat washers and large wing nuts.
UNFOLDING THE ANTENNA’S ELEMENTS
1. Hold the main boom’s longer elements near the pivot points and pull them away from the boom until they snap into the self-locking plastic support insulators.
Caution: To avoid damage to the elements, do not pull them near their outer ends. Once the elements are locked into position, do not attempt to unlock them. Doing so might break the self-locking tabs.
2. Hold each wing boom and turn its elements until they snap squarely into place (perpendicular to the boom).
3. Press the supplied small end plugs into the wing booms.
4. Bolt the triangular wing boom brackets onto the main boom using the supplied 1 1 /
2
-inch screw and small wing nut, as shown.
1
1
/
4
-Inch
Screws
Bottom Wing Boom
ATTACHING TO THE MAST
We recommend that you enlist the help of another person before you put up the mast or attach your antenna to it. How you set up your mast depends on your specific installation. Refer to the separate Consumer Product Safety Commission information sheet for recommended methods. If you plan to add this antenna to a VHF antenna’s mast, refer to “Adding the UHF Antenna to a VHF Antenna Installation” for instructions.
1. Slide the antenna’s mast clamp assembly over the end of the mast.
2. Tighten the mast clamp assembly’s lock nuts to hold the antenna in place. Do not overtighten the lock nuts.
3. Set up the mast, then rotate it so the antenna’s shorter elements point toward the broadcast antennas of the stations you want to receive.
Wing Boom Elements
Main Boom
Short Elements
Mast
Small Wing Nuts
Toward TV
Stations’
Antennas
Main Boom Long Element
Wing Boom
Brackets
Small Wing Nut
1 1 /
2
-Inch
Screw
Main Boom
ADDING THE UHF ANTENNA TO A VHF
ANTENNA INSTALLATION
To connect your UHF antenna to a VHF antenna, follow these steps.
1. Loosen the lock nuts on the VHF antenna’s mast clamp assembly. Slide the VHF antenna down the mast about 70 inches, then tighten the lock nuts to hold the antenna in place. Do not overtighten the lock nuts.
2. Mount your UHF antenna at the top of the mast. (See
“Attaching to the Mast.”)
2
15-2162a.fm Page 3 Thursday, April 27, 2000 2:21 PM
3. Use only about 70 inches of twin-lead cable to connect your UHF antenna to the VHF antenna. Be sure the cable is long enough to reach from the lead-in terminals of one antenna to the lead-in terminals of the other. Connect the cable to your UHF antenna first. (Follow the steps in the section “Using Twin-Lead Cable” on Page 2.)
4. Split the other end of the twin-lead cable for a length of about 3 inches. Then strip about 1 /
2
inch of insulation from both leads.
5. Remove the VHF antenna’s large wing nuts and flat washers from its lead-in terminals. (If you used coaxial cable to connect the VHF antenna to your TV, also remove the spade terminals from the lead-in terminals.)
6. Wrap each lead of the twin-lead cable around one of the
VHF antenna’s lead-in terminals (on both sides of the boom).
Twin-Lead Cable to UHF Antenna
VHF Antenna’s
Lead-In Terminal
Flat Washers
Large Wing
Nuts
7. Replace the spade terminals (if removed in Step 5), flat washers, and large wing nuts.
Note: In some locations, you might need to use an indoor/outdoor 300-ohm splitter/combiner (available at your local RadioShack store) to receive a satisfactory picture on your TV.
ROUTING THE CABLE TO YOUR TV/VCR
If you use coaxial cable:
• Use plastic tape or mast standoff insulators to secure the coaxial cable to the mast at about 3-foot intervals. Continue down the roof and the side of the house using roof and wall standoff insulators.
• Use coaxial cable nail-in clips every few feet to secure the cable between the mast and where the cable enters the house.
• Use a 75-ohm grounding block at the point where the coaxial cable enters the house. Read the Consumer Product
Safety Commission sheet for grounding instructions.
• Use a wall-through lead-in tube (not supplied) to neatly route the coaxial cable through walls.
If you use twin-lead cable:
• Be sure the twin-lead cable remains at least 4 inches away from all metal surfaces.
• Use standoff insulators about every 4 feet. Twist the twinlead cable about three turns between standoff insulators.
• Read the separate Consumer Product Safety Commission sheet for grounding instructions.
CONNECTING TO YOUR TV/VCR
Connect the antenna’s lead-in cable to your TV/VCR’s antenna terminals according to the type of cable you used. RadioShack carries a variety of matching transformers, if one of these suits your needs. Below are some sample connections.
Make connections as described if you have:
• Coaxial antenna lead-in
• Twin-lead TV/VCR antenna terminals
Connect to TV/VCR’s
300-Ohm Screw Terminals
RadioShack
Indoor/Outdoor
Matching Transformer
Cat. No. 15-1140
Connect
Coaxial Lead-In from Antenna
3
15-2162a.fm Page 4 Thursday, April 27, 2000 2:21 PM
Make connections as described if you have:
• Coaxial antenna lead-in
• Coaxial TV/VCR antenna terminal
Make connections as described if you have:
• Twin-lead antenna lead-in
• Coaxial TV/VCR antenna terminal
Make connections as described if you have:
• Twin-lead antenna lead-in
• Twin-lead TV/VCR antenna terminals
RadioShack
Matching Transformer
Cat. No. 15-1253
Connect to TV/VCR’s
300-Ohm Screw Terminals
Connect to TV/VCR’s
75-Ohm F-Connector
Coaxial Lead-In from Antenna
Connect to TV/VCR’s
75-Ohm F-Connector
Connect Twin-Lead
Lead-In from Antenna to
Screw Terminals
Twin-Lead Lead-In from Antenna
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES
AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DU-
RATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY
TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PER-
FORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM IN-
CONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF
RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period.
You will be charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized
Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, setup service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
15-2162 A
04/00
Printed in the USA
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project