RCA 27990 User manual

RCA 27990 User manual
INTRODUCTION
Your cordless telephone/answerer is designed to give you flexibility in use and high
quality performance. To get the most from your new cordless telephone/answerer, we
suggest that you take a few minutes right now to read through this instruction manual.
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT SAFETY
INSTRUCTIONS provided with this product and save them for future
reference.
BEFORE YOU BEGIN
Make sure your package includes the items shown here.
answerer on/off
memo
Belt clip
announce
volume
Handset
battery
erase
talk
mute
page
redial
mem
p
skip
/stop
lay
1
3
2
def
5
mno
abc
4
ghi
6
jkl
7
skip
8
pqrs
play/
stop
charge
in use
0
#
pause
oper
eras
chan
an s
Base
9
wxyz
tuv
*
tone
rev
off
e
ringer
flash
on pr
ogram
Handset
Wall mount
bracket
AC power
supply
Telephone
line cord
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular wall jack, which is the most common type
of phone jack and might look like the one pictured here. If you don’t have
a modular jack, call your local phone company to find out how to get one
installed.
DIGITAL SECURITY SYSTEM
We bring good things to life.
FCC REGISTRATION INFORMATION
Your telephone equipment is registered with the Federal Communications Commission and is in compliance with parts 15 and
68, FCC Rules and Regulations.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and Ringer
Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone
company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these
devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices
connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you
are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall,
where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not
practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service
immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a
complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where
such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these
changes are expected to affect the use or performance of your telephone equipment, the telephone company must give
you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference; and (2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician
for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C.
20402. Please specify stock number 004-000-00345-4 when ordering copies.
CAUTION: Use only the ATLINKS USA, Inc. 5-2520(white/grey)
5-2521(black) power supply that came with this unit. Using other power
supplies may damage the unit.
1. Remove the battery compartment
door on the handset, insert the
battery pack, plug the cord into
the jack (inside the
compartment), and replace the
compartment door.
2. Set the RINGER switch (on the
handset) to ON and place the
handset in the cradle on the base.
3. Plug the power supply into the
power jack on the back of the
base and plug the other end into
an electrical outlet. The “charge/
in use” indicator comes on,
5
verifying the battery is charging.
Allow the phone to charge for 12
hours prior to first use. If you
don’t properly charge the phone,
battery performance will be compromised.
3
6
IMPORTANT: Because cordless phones operate on electricity, you should have at least
one phone in your home that isn’t cordless, in case the power in your home goes out.
ANSWERING MACHINE SETUP
WARNING: TO PREVENT FIRE OR
ELECTRICAL SHOCK HAZARD, DO
NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
• Press the answer on/off button to turn the answering machine on and off. The
MESSAGES indicator lights when the answering machine is on. The indicator blinks
when you have messages.
page button answer on/off button
memo button
INSTALLATION
answerer on/off
day/check button
hour button
memo
announce
erase button
erase
3
announce button
page
volume buttons
Messages indicator
4
This telephone system meets FCC standards for Hearing Aid Compatibility.
play/
stop
ATLINKS USA, Inc.
10330 North Meridian Street
Indianapolis, IN 46290
© 2001 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
DESKTOP INSTALLATION
1. Remove the battery compartment door on the handset, insert the battery pack, plug
the cord into the jack (inside the compartment), and replace the compartment door.
2. Set the Ringer switch (on the handset) to ON, and place the handset in the cradle on
the base.
Use the flash button to activate custom calling services such as call waiting or call
transfer, which are available through your local phone company.
TIP: Don't use the talk button to activate custom calling services such as call waiting, or
you’ll hang up the phone.
CORDLESS PHONE BASICS
Use the mute button to interrupt a phone conversation to talk privately with someone
else in the room.
Headset jack
talk button
talk
redial
mem
rev
1
2
3
def
4
skip button
5
ghi
6
mno
jkl
7
8
9
wxyz
pause button
tuv
erase button
chan/ans button
*
0
tone
ERASING A STORED NUMBER
TONE/PULSE SETTING
Make sure the phone is OFF.
Press the program button.
Press * tone button for tone or # pause for pulse selection.
Press the program button again. You will hear a confirmation tone.
Press the page button on the base to get the attention of the person near the
handset, or to find a misplaced handset. Press the talk button on the handset when you
find it.
NOTE: You can still page the handset with the ringer off.
RINGER TONE SELECTION
There are 2 ringer tones for selection.
eras
chan
off
e
ringer
1. Make sure the phone is OFF.
2. Press program 1 or 2.
3. Press program to confirm the selection. You will hear a confirmation tone.
#
pause
oper
an s
charge
in use
charge/in
use indicator
rev
rev button skip button
play/stop button
DIALING A STORED NUMBER
RINGER SWITCH
skip
/stop
lay
pqrs
tone button
Make sure the phone is off.
Press the mem button.
Press any number key (0-9) to store the phone number in that memory location.
Press redial.
Press the mem button again to confirm.
1. Make sure the phone is ON.
2. Press the mem button.
3. Press the number for that memory location.
abc
play/stop
button
1.
2.
3.
4.
5.
1. Make sure the phone is OFF.
2. Press and release the mem button.
3. Press the memory location you want to erase.
4. Press and release the mem button twice.
CHAIN DIALING FROM MEMORY
Use this feature to make calls which require a sequence of numbers, for instance if you
use a calling card for a frequently called long distance number. The following example
shows how you can use chain dialing to make a call through a long distance service:
The Number For
Memory Location
Long distance access number
Authorization code
Frequently called long distance number
7
8
9
mute
mem button
redial button
Use the same procedure to change a stored number as you do to store a number but
just replace the old phone number with a new one.
1. Press mute to activate mute feature (the antenna indicator blinks).
2. Press mute again to turn it off.
PAGING THE HANDSET
mute button
rev button
MUTE BUTTON
1.
2.
3.
4.
volume
CHANGING A STORED NUMBER
STORING A REDIAL NUMBER
flash
on pr
ogram
flash/program
button
Ringer on/off
switch
MAKING A CALL
The only two things you need to know to make a call are:
• Press the talk button before you dial.
• Press talk button or place the handset in the base to hang up.
Otherwise, it works just like any other phone.
CAUTION: Because cordless phones operate on electricity, you should have at least
one phone in your home that isn’t cordless, in case the power in your home goes out.
FAST REDIAL
1.
2.
3.
4.
Make sure the phone is ON.
Press mem and then press 7.
When you hear the access tone, press mem and then press 8.
At the next access tone, press mem and then 9.
TIP: Wait for the access tones before pressing the next memory button, or your call
might not go through.
When you hear a busy tone, you can redial the previously dialed number again by
pressing the redial button.
TEMPORARY TONE
ADVANCED FEATURES
This feature enables pulse (rotary) service phone users to access touch-tone services
offered by banks, credit card companies, etc. Press the *tone button to temporarily
make the phone touch-tone compatible. For example, to get information about your
bank account:
CHANNEL BUTTON
While talking, you might need to manually change the channel in order get rid of static
caused by baby monitors, garage door openers, or other cordless phones. Press and
release the chan button to advance to the next clear channel.
THE MEMORY FEATURE
Store up to 10 numbers in memory for quick dialing.
skip
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
• Press and release announce button to review your outgoing announcement.
min button
2
FLASH BUTTON
The RINGER switch must be ON for the handset to ring during incoming calls.
REVIEWING ANNOUNCEMENT
1. Press the mem button.
2. Press a number key (0-9) to store the dialed number in that memory location. (If you
make an error storing the number, the phone beeps twice.)
3. Press the mem button.
4. Enter the number (up to 20 digits).
5. Press mem button to confirm. You will hear a confirmation tone.
CAUTION: If you make test calls to emergency numbers stored in memory, remain on
the line and briefly explain the reason for the call to the dispatcher. Also, it’s a good
idea to make these calls in off-peak hours, such as early morning or late evening.
Press the #pause button to insert a delay in the dialing sequence of a stored telephone
number when a pause is needed to wait for a dial tone (for example, after you dial 9 for
an outside line or when you need to wait for a computer access tone). Each pause
counts as 1 digit.
Press the handset VOL up or down buttons to adjust the volume of the handset's
earpiece. There are four settings.
Hi, this is (use your name here), I can't answer the phone right now, so please leave your
name, number and a brief message after the tone, and I'll get back to you. Thanks.
The phone must be OFF when you store numbers.
INSERTING A PAUSE IN THE DIALING SEQUENCE
1. Press and hold the announce button. You need to hold the button until you finish the
announcement.
2. Begin talking after you hear the beep.
3. Release the button when you finish your announcement.
If you choose not to record an outgoing announcement, a default announcement will
play. To return to the default announcement after you have recorded your own outgoing
announcement, press the announce button and release it when you hear the beep or
simply press erase while your announcement is playing.
Sample Outgoing Announcement
STORING A NUMBER IN MEMORY
To answer a call you must press the talk button on the handset before you can talk.
VOLUME BUTTON
volume button
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RECEIVING A CALL
For best results when recording, you should be about 9 inches from the microphone,
and eliminate as much background noise as possible.
CAUTION: Use only the ATLINKS USA, Inc. 5-2520(white/grey)
5-2521(black) power supply that came with this unit. Using other power
supplies may damage the unit.
This section shows you how to set up your answering machine to receive incoming
calls. Before you begin the setup, turn on the answerer.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING THE
PRODUCT.
If you need additional assistance, press the rev button when you plug in the answerer
and follow the voice instructions.
If you get a busy signal, and want to keep dialing the number, press the redial button
again to dial the number.
RECORDING THE OUTGOING ANNOUNCEMENT
7. Slip the mounting holes over the wall plate posts and firmly slide the unit down
into place.
8. Place the handset in the cradle.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
REDIAL
Press the talk button, then press the redial button to redial the last number you called
(up to 32 digits).
Set the RING SELECT switch on the back of the unit to choose the number of times you
want the phone to ring before the machine answers the call. You can choose 3 rings or
5 rings.
Certain other communications devices may also use the 2.4 GHz frequency for
communication, and, if properly set, these devices may interfere with each other and/
or your new telephone. If you are concerned with interference, please refer to the
owner’s manual for these devices on how to properly set channels to avoid
interference. Typical devices that may use the 2.4 GHz frequency for communication
include wireless audio/video senders, wireless computer networks, multi-handset
cordless telephone systems, and some long-range cordless telephone systems.
THE LIGHTNING FLASH
AND ARROW HEAD
WITHIN THE TRIANGLE
IS A WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE THE
PRODUCT.
The phone is on when the antenna indicator on the handset and the charge/in use
indicator on the base is lit. The antenna indicator and the charge/in use indicator on
the base flashes when you receive a call.
SETTING THE RING SELECT
4. Remove the handset from the cradle and set aside. Turn the base over and align four
slots on the bottom of the base with the four hook-tabs on the bracket.
5. Insert the hook-tabs into the slots and push upwards until the bracket snaps
securely into place.
6. Plug the telephone line cord into the TEL LINE jack on the back of the base and into
a modular phone jack.
NOTE: If desired, gather the extra telephone line cord together, fasten with a wire tie,
and store inside the wall mounting bracket.
HEARING AID COMPATIBILITY
Model 27990A
15714270 (Rev. 1 DOM E)
01-24
Printed in China
7
When you place the handset in the base, the unit verifies its security code. After a
power outage or battery replacement, you should place the handset in the base for
about 20 seconds to reset the code.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1. Press and hold the day/check button to set the day of the week.
2. Press the hour button to set the hour (a.m. or p.m.).
3. Press the min button to set the minute. When you press and hold the min button, the
time advances in 5-minute intervals.
4. Press and release the day/check button to review the day and time settings.
VOICE INSTRUCTIONS
NOTE: If desired, gather the extra power adapter line cord together, fasten with a wire
tie, and store inside the wall mounting bracket.
CAUTION:
CHARGE/IN USE INDICATOR
Use the volume + or - switches on the base to adjust speaker volume to a comfortable level.
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that may
cause interference to nearby TVs, microwave ovens, and VCRs. To minimize or prevent
such interference, the base of the cordless telephone should not be placed near or on
top of a TV, microwave oven, or VCR. If interference continues, moving the cordless
telephone farther away from the TV, microwave oven or VCR will often reduce or
eliminate the interference.
SETTING THE VOICE TIME/DAY STAMP
SETTING THE SPEAKER VOLUME
WALL MOUNT INSTALLATION
PARTS CHECKLIST
rev
3. Plug the power supply into the power jack on the back of the base and the other end
into an electrical outlet. The “charge/in use” indicator comes on, verifying the
battery is charging.
Allow the phone to charge for 12 hours prior to first use. If you don’t properly
charge the phone, battery performance will be compromised.
4. Plug the telephone line cord into the TEL LINE jack on the back of the base and into
a modular phone jack.
p
27990
40-Channel 2.4 GHz
Cordless Telephone with
Digital Answerer
User’s Guide
1. Call the bank’s information line.
2. Press the tone key, denoted with (*) on the keypad, when your call is answered.
3. Follow the voice menu instructions to get the information. When you hang up, the
phone goes back to pulse (rotary) service.
ANSWERING MACHINE OPERATION
USING THE HANDSET
ANSWERER STATUS INDICATORS
GENERAL PRODUCT CARE
LIMITED WARRANTY
This section highlights the buttons and features on the answering machine.
To access the answering machine from the cordless handset, press the ans button.
0-59
Total number of messages.
CL (blinking)
__
The voice time/day stamp needs to be set.
MESSAGES INDICATOR
After you access the answerer, use the marked handset keys just as if you were
pressing the corresponding buttons on the base (see "Answering Machine Operation"
for details on functions). The functions are listed on the handset above each number
key. For example, to play messages:
An (blinking)
Currently answering a call.
1. Press the ans button.
2. Press 2 (play/stop).
3. When you are finished listening to your messages, press ans button again.
F (blinking)
Memory is full.
Six bars (blinking)
Recording a memo or announcement.
LA (Line Access)
External line remote answerer.
To keep your telephone working and looking good, follow these guidelines:
• Avoid putting the phone near heating appliances and devices that generate
electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping and rough treatment to the phone.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this will damage
the finish.
• Retain the original packaging in case you need to ship the phone at a later date.
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days from date
of shipment to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The exchange unit is
under warranty for the remainder of the original product’s warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were originally provided
with the product. We recommend using the original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the product is within the warranty period, must be presented to obtain
warranty service.” For rental firms, proof of first rental is also required. Also print
your name and address and a description of the defect. Send via standard UPS or its
equivalent to:
ATLINKS USA, Inc.
c/o Thomson multimedia Inc.
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service not covered by
the warranty.
• Insure your shipment for loss or damage. Atlinks accepts no liability in case of
damage or loss.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. Any additional information, should be
obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
The messages indicator blinks to show you how many new messages you have. The
answer on/off button must be on in order for the messages indicator to work.
SCREENING CALLS FROM THE BASE
You may screen incoming calls by waiting for the caller to begin leaving a message (to
hear who it is), then pick up the handset, and press talk to talk to the caller. The
answering machine automatically stops recording when you activate the handset or
pick up an extension phone.
TIP: Make sure the volume on the base is set loud enough to hear your incoming calls.
MESSAGE PLAYBACK
The messages indicator lets you know when you have messages. To play messages,
press play/stop.
While a message is playing, you may do the following:
• Press play/stop to stop the message playback.
• Press and release rev to restart the current message; continue to press and release
rev to go to previous messages.
• Press and release skip to go to the next message.
• Press play/stop to stop message playback.
When the internal memory is full, the system answers after 10 rings. You may erase
some messages so the answerer will record new messages.
ERASING MESSAGES
You may erase messages three ways: one message at a time using the erase button on
the base; all messages using the erase button on the base; or one message at a time
using the erase button (0) on the handset or a phone in another location.
• To erase a message, press play/stop on the base and press and release erase
button on the base to erase the message that is playing.
• To erase all messages, press the erase button on the base when messages have
stopped playing.
• To erase a message from the handset:
1. Press answer button on the handset.
2. Press play/stop on the handset (the 2 button).
3. Press erase on the handset (the 0 button) to erase the
message that is playing.
NOTE: You may only erase messages that have been reviewed. Erased messages cannot
be restored. Also, be careful not to press erase button as the next unheard message is
playing because that message will also be erased.
LEAVING A MEMO
The antenna indicator comes on if the answerer is being accessed by the handset.
SCREENING CALLS FROM THE HANDSET
Use the handset to screen calls even when you can't hear the answering machine.
When the phone rings:
1. Press the ans button to access the answering machine.
2. Listen as the caller leaves a message.
3. Press the talk button to speak to the person or press ans button to stop
screening the call.
MEMORY FULL
When the unit’s internal memory is full, the system answers after 10 rings, beeps and
waits for the 3-digit security code. If you don't enter the security code within 10 seconds
after the unit beeps, the phone hangs up.
You must erase some of the messages in order for the system to record new incoming
messages.
NOTE: The unit also answers after the 10th ring if it is turned off. To access the
answerer from another location, enter your 3-digit security code after you hear the
beep.
ACCESSING THE ANSWERER FROM ANOTHER
PHONE
You can access your answering machine from any touch-tone phone by entering your
3-digit security code after you hear the outgoing announcement.
1. Dial the phone number for the answering machine.
2. Enter the security code after you hear the tone.
3. Follow the voice menu instructions to use the answerer's remote functions.
The remote feature enables you to perform the following functions:
To
Press this Button
Review message
Play back messages
Stop message playback
Erase message
1
2
2
0 (during message
playback)
3
4
7
Use the Memo feature to leave a message.
1. Press and hold the memo button. (You must hold down the button until you finish
recording the message.)
2. Begin speaking after you hear the beep.
3. Release the memo button when you are finished.
Skip message
Turn off answerer
Review voice menu options
REMOTE ACCESS
TIP: You can bypass the outgoing announcement by pressing any numbered key on the
keypad while the announcement is playing. Then, you can enter your security code to
access the answering machine.
This section explains two types of remote access: using the handset to access the
answering machine and accessing the answering machine from another phone.
The handset contains integrated buttons that enable you to access the answering
machine with the handset.
You can also access your answering machine from any phone that is tone-dial
compatible by entering a 3-digit security code after you hear the outgoing
announcement. A voice menu system guides you through all of the steps.
NOTE: The 7-segment message indicator will display LA when answerer is accessed
from another phone.
CHANGING THE SECURITY CODE
The default security code for accessing the answerer from another location is 1 2 3.
You must use the handset to change the security code. With the phone off, follow
these steps:
HANDSET SOUND SIGNALS
1. Press ans button (the antenna indicator comes on).
2. Press tone (*).
3. Enter 3 numbers to be used as the new security code.
4. Press tone (*) again.
CONNECTING AN
OPTIONAL HEADSET TO
•
•
•
•
Headset
jack
THE HANDSET
For hands free conversation, connect the
headset (optional) to the HEADSET jack as
shown. The handset receiver and microphone
are disabled when the headset is connected.
Adjust the headset to rest comfortably on top of
your head and over your ear. Move the
microphone to approximately 2 to 3 inches from
your mouth.
Headset
plug
• Press the TALK button to answer or place a
call before using the headset.
CONNECTING THE BELT
CLIP
Slot for
belt clip
Signal
Meaning
Three long beeps or continuous beeps
A long warbling tone (with ringer on)
One short beep every few seconds
Page signal
Incoming call signal
Battery low
CAUSES OF POOR RECEPTION
HEADSET AND BELT CLIP OPERATION
HEADSET
MEMORY FULL
ANSWERER INDICATOR
Answerer off.
Slot for
belt clip
•
•
•
•
•
•
•
Aluminum siding
Foil backing on insulation
Heating ducts and other metal construction that can shield radio signals.
You’re too close to appliances such as microwaves, stoves,
computers, etc.
Atmospheric conditions, such as strong storms
Base is installed in the basement or lower floor of the house.
Base is plugged into AC outlet with other electronic devices.
Baby monitor is using the same frequency.
Handset battery is low.
You’re out of range of the base.
Microwave oven is using the same frequency.
SERVICE
FCC requires this product be serviced only by the manufacturer or its authorized
service agents. In accordance with FCC requirements, changes or modifications not
expressly approved by ATLINKS USA, Inc. could void the user’s authority to operate this
product. For instructions on how to obtain service, refer to the warranty included in this
guide or call customer service at 1-800-448-0329.
There are two slots, one on each side of the
handset.
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
• Attach the belt clip by inserting the sides of
the belt clip into the slots. Snap the ends of
the belt clip into place.
Attach your sales receipt to the booklet for future reference or jot down the date this
product was purchased or received as a gift. This information will be valuable if service
should be required during the warranty period.
CHANGING THE BATTERY
Purchase date ________________________________________________
Make sure the telephone is OFF before you replace battery.
Name of store ________________________________________________
1. Remove the battery compartment door.
2. Disconnect the cord attached to the battery pack and
remove the battery pack from the handset.
3. Insert the new battery pack and connect the cord into
the jack inside the handset.
4. Put the battery compartment door back on.
5. Place handset in the base to charge. Allow the
handset battery to properly charge (for 12 hours)
prior to first use or when you install a new battery
pack. If you do not properly charge the phone,
battery performance will be compromised.
BATTERY SAFETY PRECAUTIONS
• Do not burn, disassemble, mutilate, or puncture. Like
other batteries of this type, toxic materials could be
released which can cause injury.
• To reduce the risk of fire or personal injury, use only
the battery listed in the User’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
• Please complete and mail the Product Registration Card packed with your unit. It
will make it easier to contact you should it ever be necessary. The return of the card
is not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION
GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A
GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES
AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF
INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above
limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights
that vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement