INSTRUCTION MANUAL
MIDGET MUSTANG 60
Wing Span: 59.5 in / 1510 mm
Wing Area: 667 sq in / 43.0 sq dm
Flying Weight: 7.5 lbs / 3400 g
Fuselage Length: 51.0 in / 1290 mm
Requires: 2-stroke 0.60-0.75 or 4-stroke 0.91 engine
4-channels radio w/ 5 standard servos
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
Www.thewingsmaker.com
GA028
MIDGET MUSTANG 60
I N D E X
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P. 3 -P.10
P. 11
BEFORE YOU BEGIN
1
Read through the manual before you begin, so you will have an overall idea of what to do.
2
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
3
Symbols used throughout this instruction manual comprise of the following : -
Apply epoxy glue.
Apply thread locker
Assemble left and right sides the same way.
Peel off shaded portion covering film.
3mm
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
Apply instant glue
(C.A.glue, super glue.)
Must be purchased separately!
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Pierce the shaded portion covering film.
Warning!
Do not overlook this symbol!
P.1
Parts List
1. MAIN WING -- 1 pair
2.SERVO MOUNTING PANEL (For Aileron) -- 1 pair
SCREW PWA2x 8 mm -- 8 pcs
3. SCREW
PB2 x20mm -- 6 pcs
TRI-HORN M 3x14mm (L) -- 2 sets
CLEVIS -- 2 pcs
STRAPER -- 2 pcs
FUEL TUBE Φ6x5mm -- 4 pcs
PUSHROD Φ1.8x105mm w/ Threads (For Aileron Servo) -- 2 pcs
4. MAIN LANDING GEAR--1 pair
MAIN LANDING GEAR COVER--1 pair
MOUNTING PLATE PL4114020 -- 4 pcs
SCREW PA2.6x10mm -- 8 pcs
SCREW PM2x8mm-- 8 pcs
WASHER d2xD5mm -- 16 pcs
M2 NUT -- 8 pcs
5.SCREW PA2.6x10mm -- 4 pcs
COLLAR Φ4.1mm w/ set screw -- 4 sets
WHEEL PANTS -- 1 pair
MAIN WHEEL Φ80mm -- 2 pcs
MOUNTING PLATE PL4114020 -- 2 pcs
6. WING JOINER 9x25x125mm -- 1 pc.
7. STABILIZER & ELEVATOR -- 1 set
FUSELAGE- - 1 pc.
8. VERTICAL FIN & RUDDER -- 1 set
TAIL LANDING GEAR -- 1 set
TAIL WHEEL Φ25mm -- 1 pc.
SCREW PA3x12m-- 2 pcs
COLLAR Φ2.1mm w/ set screw -- 1 set
9. FUEL TANK 380cc -- 1 set
PLYWOOD 3x15x110mm (For Fixing Fuel Tank) -- 1 pc.
BALSA 6x15x78mm (For Fixing Fuel Tank) -- 1 pc.
10.ENGINE MOUNT PL5111070 -- 1 set
SOCKET HEAD SCREW M4x25mm
WASHER d4xD15mm -- 4 pcs
–
4 pcs
11.SCREW PM4x30mm -- 4 pcs
SPINNER Φ82 mm -- 1 pc.
THROTTLE PUSHWIRE Φ1.2x460mm
w/ Plastic Tube d2xD3x240mm -- 1 set
P.2
WASHER d4xD9mm -- 8 pcs
M4 NUT -- 8 pcs
12. COWLING -- 1 pc.
T RANSPARENT DUMMY COWLING -- 1 pc.
SILICON GROMMET d1.5xD6.5mm -- 5 pcs
SCREW PWA2.6 x 12mm -- 5 pcs
13.LINKAGE CONNECTOR Φ 2.1mm -- 1 set
14.SCREW PB2x16mm -- 3 pcs
TRI-HORN M3x14mm (L) -- 1 set
CLEVIS -- 1 pc.
FUEL TUBE Φ6x5mm -- 1 pc.
PUSHROD Φ1.8x615mm w/ Threads (For Rudder) -- 1 pc.
15.SCREW PB2x16mm -- 6 pcs
TRI-HORN M3x14mm (L) -- 2 sets
CLEVIS --2 pcs
FUEL TUBE Φ6x5mm -- 2 pcs
PUSHROD Φ1.8x525mm w/ Threads (For Elevator) -- 2 pcs
16. BALSA 6x6x143mm (For Servos Stand) -- 2 pcs
PLYWOOD 3x116x172.5mm (For Servos Stand) -- 1 pc.
FUEL TUBE Φ6x5mm -- 2 pcs
STRAPER -- 2 pcs
PUSHROD CONNECTOR -- 1 set
PUSHROD Φ1.8x90mm w/ Threads (For Elevator) -- 1 pc.
SPONGE 60x70x110mm -- 1 pc.
17.CANOPY -- 1 set
SCREW PWA2.3X8mm -- 5 pcs
SILICON GROMMET d1.5xD6.5mm -- 5 pcs
18.SCREW PM4x35mm -- 2 pcs
WASHER d4xD15mm -- 2 pcs
PLASTIC PLATE 1x40x110mm (Wing Protection) -- 1 pc.
19.DECALS: GA028DEC -- 1 set
COVERING:--
TOUGHLON STL 100 WHITE
TOUGHLON STL 201 BLACK
TOUGHLON STL 330 CADMIUM YELLOW
TOUGHLON STL 580 PEARL BRONZE
1
Main Wing
Peel off shaded portion covering film.
Aileron Servo Lead
Pre-glued
2
Aileron Servo
PWA 2 x 8mm
PWA 2 x 8mm
Screw
8
2mm
Bottom View
Aileron Servo Cover
3 x 68 x 76mm
1.5mm
Bottom View
3
Aileron Servo
PB2 x 20mm
Screw
6
PB2 x 20mm
Clevis
Pushrod
Φ1.8x105mm
Fuel Tube
Φ6 x 5mm
Tri-horn
M3 x 14mm
2mm
Straper
Pushrod
Φ1.8 x 105mm
Fuel Tube
Φ6 x 5mm
Φ1mm pilot holes for The Wing s
Maker tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces.
P.3
Bottom View
4
Main Wing
Peel off shaded portion covering film for lead to another aileron servo.
Wing Joiner
9x25 .
2x124 .
5mm
Peel off shaded portion covering film.
Lead to aileron Servo.
Please dry fit wing joiner into left and right wing to make sure they fit with the proper dihedral angle
, mark the wing joiner if necessary. Apply glue to both sides of all surfaces in contact. Use a stick to apply glue to inner side of wing joiner sleeve, and apply glue to wing joiner before putting them to gether. Wing joiner not glued properly will lead to wing failure and plane crash.
5
Landing Gear
PA2.6 x 10mm
Screw
8
PM2 x 8mm
Screw
8 d2xD5mm
Washer
16
M2
Nut
8
M2 Nut d2xD5mm
M2 Nut d2xD5mm
Main Landing Gear Cover
PM2 x 8mm
1mm
PA2.6 x 10mm
Bottom View
6
Wheels And Pants
PA2.6 x 10mm
Screw
4
3mm
Set Screw
4
4.1mm
Collar
4
1.5mm
PA2.6 x 10mm
3mm Set Screw
Completed
4.1mm Collar
Main Wheel Φ 80mm
P.4
7
Stabilizer & Elevator
B
(Stabilizer)
B'
(Main Wing)
B=B'
A
A’
A=A’
Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible.
8
Vertical Fin & Rudder
PA3 x 12mm
Screw
2
3mm
Set Screw
1
2.1mm
Collar
1
Pre-glued
Pre-glued
Pre-glued
C C'
C = C'
3mm Set Screw
2.1mm Collar
PA3 x 12mm
PA3X12mm
Tail Wheel Φ25mm
P.5
9
Fuel Tank
(
Install Plywood 3x15x110mm
For Fuel Tank Position Fixing )
Fuel Tank
380cc
Plywood
3 x 150x 110mm
Fuel Tank
380cc
Balsa 6x15x78mm
Bottom View
Fuel Tank
380cc
UP
Balsa 6x15x78mm
10
Engine Mount
M4 x 25mm Socket Head Screw
4 d4xD15mm
Washer
4
Bottom View
M 4 x 25mm d4 x D15mm Washer
Engine Mount
PL5111070
Engine Mount
PL 5111070
M4 x 25mm
4mm
Inverted Mount
P.6
Illustration is for inverted mount.
You can mount your engine upright or sideways simply by rotating the engine mount,thrust angles will not be affected.
Blind nuts are off-centered to keep the spinner at the fuselage axis.
11
Engine
PM4 x 30mm
Screw
4 d4xD9mm
Washer
8
M4
Nut
8
PM 4 x 30mm
Installed Engine Position
130mm
5.04in
M4 NUT
Washer
d4xD9mm
PM4X30mm d4 x D9mm
Washer
M4
Nut
Throttle Pushwire
Ø1.2x460mm
Plastic tube
d2xD3x240mm
Bottom View
12
Cowling
PWA2.6 x 12mm
Screw
5 d1.5 x D6.5mm
Silicon Grommet
5
Please refer to the attached sheet for usage of the transparent 3D template
First insert the grommet to the cowling then apply screw.
PWA2.6 x 12mm
d1.5xD6.5mm
Silicon Grommet
1.5mm
Spinner
Ø82mm
P.7
13
Servo Set
LINKAGE CONNECTOR
3 x 3mm
Set Screw
1
Linkage Connector
1
M2
Nut
1 d2xD5mm
Washer
2
Th ro ttl e p us hw ire
2mm
2mm
M2 Nut
3mm
Included with the radio Set.
Throttle Servo.
Please refer to the attached sheet for linkage connector installation.
14
Rudder Pushrod
PB2 x 16mm
Screw
3
Ø1mm pilot holes for The Wings Maker tri-horn drilled.
Please look for pin-hole marks at side of control surfaces.
80m m
30mm
PB2x16mm
Fuel Tube
Ø6x5mm
Clevis
Rudder Pushrod
Ø1.8x615mm
Tri-horn
M3x14mm
15
Elevator Pushrod
PB2 x 16mm
Screw
6
70m m
155 mm
Bottom View
Please look for pin-hole marks at under side of control surfaces.
Elevator Pushrod
Ø1.8x525mm
Bottom View
Fuel Tube
Ø6x5mm
Clevis
PB2X16mm
Tri-horn
M3x14mm
P.8
16
Radio Equipment
Receiver Switch Harness
Balsa 6 x 6 x143mm
Install and arrange the servos as shown in the diagram.
Fuel Tube
Φ6 x 5mm
J1 ( Pushrod Ø1 .
8x90mm )
J1
Rudder
Servo
J2
J2 ( Pushrod Ø1 .
8x525mm )
Straper
Plywood 3 x 120 x 173mm
M2
Elevator Pushrod
1. 8X90mm Elevator Servo
Elevator
Servo
Sponge
Throttle
Servo
Battery
Throttle Pushwire d1.2 x 460mm w/ Plastic Tube d2 x D3 x 240mm
Bottom View
KA2X8mm
Pushrod Connector
First insert the grommet to the canopy then apply screw.
17
Canopy
PWA2.3 x 8mm Screw
5 d1.5 x D6.5mm
Silicon Grommet
5
PWA2.3 x 8mm d1.5xD6.5mm
Silicon Grommet
18
Main Wing
PM4 x 35mm
Screw
2 d4 x D15mm
Washer
2 d4 x D15mm
PM4 x 35mm
Wing Protection
1 x 40 x 110mm
P.9
19
Wing Setting
Adjust the wing and fuselage configuration as shown in the diagrams.
B'
B
A
A'
C
A = A'
B = B'
C = C'
C'
20
Control Throws
Elevator
Rudder
Aileron
20mm
20mm
Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.
30mm
30mm
10mm
10mm
21
C.G.
90mm
3.54 in.
The ideal C.G. position is 90mm (3.54 in) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.
90mm(3.54in)C.G.
P.10
www.thewingsmaker.com
Warning!
Important Safety Precautions
#First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
#MIDGET MUSTANG is specially designed to be powered by 2C 0.61 engine may cause severe damage and injuries.
-0.75
or 4C 0.91 engine, using a more powerful engine does not mean better performance. In fact, over powered
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
LINKAGE CONNECTOR
HW7111050 & HW7111060
Drill 2mm hole at servo horn.
Insert linkage connector into servo horn.
Make sure shoulder of screw is cleared from servo horn.
Add washer to reduce play if necessary.
Shoulder
Tighten up the round nut against the shoulder. Apply
CA or permanent thread locker.
After fastening the round nut, make sure that the linkage connector can rotate freely.
Usage of the transparent 3D template
This transparent 3D template is used for position guidance of the actual cutting of the pre-painted cowling.
1
2
3 4
Simply cut the transparent 3D template to fit your engine and exhaust pipe, then slide onto the actual cowling and use as template to mark the openings required for final cutting.
THE WINGS MAKER
* GA028PO18700810*