RCA DRC99310KP User manual

RCA DRC99310KP User manual
user manual
DRC99310KB Blue
DRC99310KR Red
DRC99310KP Purple
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted
material without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for
limited viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.
AVC Multimedia,
Markham, Ontario L3R 1E3
http: //www.RCAav.com
Safety Precautions
The lightning flash with an arrowhead symbol,
within the equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of
sufficient magnitude to cause an electric shock.
* SEE BOTTOM OF UNIT FOR
GRAPHIC SYMBOLS *
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing)
instructions in this owner’s manual.
WARNING: Should any trouble occur, disconnect the AC power adapter and refer servicing to a qualified
technician.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
CAUTION: Use of controls or adjustments or performance of procedures other than
those specified may result in hazardous radiation exposure.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE.
1.
2. 3. 4. 5. 6. 7. 8. 9.
10.
11.
12.
13.
14.
This product contains a
low power laser device.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block the ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of a polarized or grounding - type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as the AC power cord or plug is damaged, liquid has spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Please check and identify the supplied accessories.
On Placement
DC IN
2 To
9V jack
Using the Remote Control
Remove the
PLASTIC sheet
before using the
Remote Control.
To Change Remote Battery
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
Battery Replacement
When the battery becomes weak, the operating distance of the remote control will be greatly reduced and
you will need to replace the battery.
Note: If the remote control is not going to be used for a long time, remove the battery.
WARNING: Do not dispose of the battery in a fire or it may leak and/or explode.
WARNING: Batteries should not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
Control Reference Guide
Remote Control
VIDEO
MODE
1
2
3
4
MENU
PREV
SEARCH
NEXT
STOP
GOTO
9
10
11
On Safety
• When connecting or disconnecting the AC power adapter, grip the plug and not the cord itself.
Pulling the cord may damage it and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power adapter.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form
inside the unit. When there is condensation inside the unit, the unit may not function normally. Let
the unit stand for 1 to 2 hours before turning the power on, or gradually heat the room and allow
the unit to dry before use.
Ventilation Warning
• Do not block the ventilation openings or holes. If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.
• Do not operate the unit in a confined space, such as a bookcase or built-in cabinet. Allow about 4
inches (10cm) of free space all around the unit for adequate ventilation.
Rating Plate Location
• The rating plate is located on the bottom of unit.
FCC Statements
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
E-1
DRC99310K_ENGLISH IB 7pt_594x297mm.indd 1
ANGLE
MEMORY
DVDs
[8cm/12cm disc]
DISPLAY
M
AUDIO
3
2
SUBTITLE/
RETURN
Audio CDs
[8cm/12cm disc]
7
4
5
7
8
6
12
13
14
15
Compatible
Region Management Information
9
0
A. Using the AC Power Adapter
The supplied AC power
adapter operates on AC
100-120V.
8
A-B
DISC
REPEAT
The region number of this unit is 1.
Disc Function or Operation That is Not Available
When the symbol appears on the screen, it indicates the function or operation attempted is not available
at that time. This occurs because the DVD manufacturer determines the specific functions of DVDs. Certain
functions may not be available on some DVDs. Be sure to read the documentation provided with the DVD.
Icons Used on DVDs
Language selections for audio
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
Region code indicator
Sample lcons
Note:
When playing back a CD-G (Graphics) or CD EXTRA disc,
the audio portion will be played, but the graphic images
will not be shown.
1
Titles, Chapters and Tracks
• DVDs are divided into “titles” and “chapters”.
If the disc has more than one movie on it, each
movie would be a separate “title”. “Chapters”
are sections of titles.
• Audio CDs are divided into “tracks”. A “track” is
usually one song on an Audio CD.
Title1
Title2
Chapter1
Chapter2
Chapter3
Chapter1
Chapter2
Track1
Track2
Track3
Track4
Track5
Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded
on them, but some do not.
Note on Unauthorized Discs
You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your
geographic area or made for business purposes.
E-2
9. MENU button
Enter and exit the main DVD Menu.
10.
NEXT button
Skip to next title, chapter or track on a disc.
11. STOP button
Stop playing a disc.
PLAY button
Start or resume playback of a disc.
PAUSE button
Press once to pause playback. Press
subsequently to advance frame by frame on
a DVD.
12. DISPLAY button
Show status information on the screen.
13. ANGLE button
Switch between multiple camera angles if
applicable to the DVD.
14. AUDIO button
Select one of the audio sound tracks on a
DVD (if more than one is available) or select
the audio output mode on a CD.
15. SUBTITLE button
Select one of the subtitle languages
programmed on a DVD (if available).
RETURN button
Return to normal operation after using the
SETUP menu of a DVD.
1. VIDEO MODE button
Adjust Brightness, Screen Size and Contrast
of the LCD screen.
2.
PREV button
Move back through titles, chapters or tracks
on a disc.
3.
/
SEARCH buttons
SEARCH:
Fast reverse playback.
SEARCH:
Fast forward playback.
4. GOTO button
Skip directly to a location on a CD/DVD.
5. Cursor ( , , , ) buttons
Move between selections on a menu screen
and adjust certain settings.
ENTER button
Confirm selections on a menu screen.
6. MEMORY button
Set titles/chapters in a favorite order.
7. Number (0 - 9) buttons
Use when creating programs or locating a
title/chapter/track or specific time.
8. REPEAT A-B button
Perform point-to-point repeat playback on a
DVD or CD.
REPEAT DISC button
Repeat a DVD chapter or title.
Repeat a CD track or the whole disc.
SETUP button
In Stop Mode, press to display the unit’s
SETUP menu.
E-3
the switch
3 Slide
to CHARGE
4
Charging
light ON
5 Recharging
is completed
when charging
light goes out
Warning:
• The built-in battery can only be recharged when the unit is in CHARGE mode while using the AC
power adapter.
• The built-in battery cannot be recharged when the unit is in ON mode.
• Do NOT recharge the built-in battery in a vehicle using the car power adapter.
• Batteries should not be exposed to excessive heat such as sunshine, fire or the like.
Note:
• When the built-in battery power is low, "Battery Low" will display on the screen and the unit will stop
playing.
• Recharge the built-in battery when you are ready to use it again.
• While using the built-in battery, the environmental temperature should be 41°F (5°C) to 95°F (35°C).
• To get the longest service life of the built-in battery, charge at indoor-temperature.
• The built-in battery in this device may present a risk of fire or chemical burn if mistreated. Do not
disassemble, heat above 212oF (100oC), or incinerate.
• The unit should not be exposed to excessive heat such as sunshine, fire or the like.
• When discarding the unit, environmental problems must be considered and local rules or laws
governing the disposal of such products must be strictly followed.
Turning on the Unit
1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the
ON position.
2. The start-up picture will appear on the screen.
3. After use, slide the CHARGE / STANDBY / ON switch to the STANDBY (power
off ) position.
Power Supply
SETUP
Region Management Information: This unit is designed and manufactured to respond to the Region
Management Information that is encoded on DVDs. If the region number printed on the DVD does not
correspond to the region number of this unit, it cannot play that disc.
NEXT button
Press to advance titles / chapters / tracks.
In DVD Menu or Setup Menu, press to scroll
right.
SEARCH button
Press to perform fast reverse playback during
CD playback.
In DVD Menu or Setup Menu, press to scroll
down.
8. Disc Door
Push to close the disc door.
9. OPEN knob
Press the open knob to open the disc door.
10.Remote sensor
Senses the remote control's signals.
11.ON indicator
12.CHARGING indicator
Charge the rechargeable battery before
using it for the first time. Complete charging
typically takes approximately 4-5 hours. The
charging light will go out when the battery
becomes fully charged.
1. LCD screen
2. DC IN 9V - 12V jack
3. AUDIO / VIDEO OUT jack
4. CHARGE / STANDBY / ON switch
5. VOLUME control
Adjusts the volume.
6. Headphone jack
7. STOP button
Press to stop playing a disc.
MENU button
Accesses DVD Disc Menu if DVD disc is
currently playing.
Accesses Setup menu if disc is not playing.
button
Press to start or resume playback of a disc.
Pressing during playback of a disc will cause
playback to be paused.
SEARCH button
Press to perform fast forward playback
during CD playback.
In DVD Menu or Setup Menu, press to scroll
up.
PREV button
Press to go back to the previous title /
chapter / track.
In DVD Menu or Setup Menu, press to scroll
left.
PAUSE
ENTER
The unit can play back
AC power
adapter
Connections
1
To wall outlet
AC power
adapter
A. Connecting a TV
2 To DC IN 9V Jack
Cautions:
• The AC power adapter included with this unit is for its use only. Do not use it with other equipment.
• When the unit is not going to be used for long time, disconnect the AC power adapter from the wall outlet.
• When the AC power adapter is plugged in, the apparatus is not completely disconnected from the
main power supply, even when the power is turned off.
Warning:
The AC/DC adaptor is used as disconnect device. The AC/DC adaptor of apparatus should not be
obstructed OR should be easily accessed during intended used. To be completely disconnect the power
input, the AC/DC adaptor of apparatus shall be disconnected from the mains.
If your TV has audio/video inputs, you can connect the unit to your TV using standard Audio/Video cables.
White Red Yellow
To AUDIO / VIDEO
OUT jacks
Audio / Video cable
(not included)
White Red Yellow
• Do not use the unit in places that are extremely hot, cold, dusty or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a
cloth, or by placing it on carpeting.
• To avoid magnetizing, do not place the unit near speakers or magnets.
• Do not use this unit in direct sunlight or leave the unit in a closed automobile (or similar
environments) where it would be exposed to high temperatures above 104°F (40°C).
• No naked flame sources such as lighted candles should be placed on the AC power adapter or the main
unit.
• The AC/DC adaptor and apparatus should not be exposed to splashing or dripping liquids, and no
objects filled with liquids, such as vases, should be placed on the AC/DC adaptor and apparatus.
• The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, should be placed on apparatus.
AC power
1 To
outlet
Remote Control
5
6
Disc Formats
To recharge the built-in battery
.Remote Control (with battery)................................................................................................................................... x 1
AC Power Adapter........................................................................................................................................................... x 1
Car Power Adapter..........................................................................................................................................................x 1
Earphone.............................................................................................................................................................................x 2
Headphone Splitter.........................................................................................................................................................x 1
Carrying Bag......................................................................................................................................................................x 1
PLAY
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
C. Using the Built-in Battery
The unit has a built-in, non-replaceable, rechargeable battery. Charge the built-in battery before using it
for the first time. Complete charging typically takes approximately 4-5 hours. The charging light will go
out when the built-in battery becomes fully charged.
• Point the remote control at the REMOTE SENSOR located
on the unit.
• When using this unit in very bright light, the infrared
REMOTE SENSOR may not work properly.
Important Safety Instructions
Read these instructions before using your new product for the first time.
Unit
Accessories
TV
Watching a DVD on your TV
1. Turn on the unit.
2. Turn on the TV and follow the instructions included with it to watch video from external sources.
B. Using the Car Power Adapter
The 12V car power adapter
allows the unit to be used
with vehicles that have a 12V,
negative ground electrical
system.
B. Using Headphones/Earphones
1
To cigarette
lighter socket
Car power adapter
• Turn down the volume before connecting, and then adjust the level.
• When headphones/earphones are connected, no sound will be emitted from the unit's speaker.
2 To DC IN 9V Jack
Warning:
Disconnect the car power
adapter when not in use. Not
for use in 24V vehicles.
Headphone Splitter
(included)
Caution:
• Use the provided 12V car power adapter only. Use with other car power adapters could damage the
unit.
• The 12V car power adapter included with this unit is for its use only. Do not use it with other
equipment.
• In the interest of traffic safety, do not operate this unit or view videos while driving a vehicle.
• Make sure the unit is securely fastened to prevent it from falling or flying through the air in the event
of an accident.
• When the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may
become hot due to poor contact. Be sure to clean the cigarette lighter socket before use.
• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.
E-4
Headphones/Earphones
(3.5mm diameter plug) (included)
Caution:
Avoid listening to sound at levels which may be harmful to your ears.
E-5
2010-6-18 16:17:10
Display Function
Playing a Disc (Basic Playback)
While the disc is playing, press the DISPLAY button repeatedly to display information on operation status.
This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced
in a manner that allows specific or limited operation during playback. Therefore, this unit may
not respond to all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions
accompanying the specific DVD in question for more information about the options available on that
DVD.
“
” may appear on the screen during operation. A “
” means the desired operation is not
permitted by the unit or disc.
Playing a Disc
1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the ON position.
See Customizing the function settings before proceeding to step 2.
2. Press the OPEN knob to open the disc door.
3. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up, pushing
gently until you hear a “click”.
4. Close the disc door. It takes a short while for your unit to load the disc. After loading, the unit will
automatically bring you to the main menu of the DVD or start playing the DVD.
5. If the unit does not automatically start playing the DVD, press the  PLAY button on the remote
control or button on the unit.
Pausing Playback (Still Mode)
Press the PAUSE button. To resume normal playback, press the PLAY button on the remote control
or button on the unit.
For a DVD, each time you press the PAUSE button on the remote control, the picture advances one
frame.
Stopping Playback
Press the STOP button at the location where you want to interrupt playback. To resume playback at the
position where the disc was stopped, press the PLAY button on the remote control or button on the
unit.
If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAY button
on the remote control or button on the unit will reset the DVD to the beginning.
Fast Forward / Fast Reverse
1. Press the SEARCH
or
SEARCH button when a disc is playing. Each time you press the SEARCH
or  SEARCH button, the playback speed changes in the following sequence:
2. Press the
PLAY button on the remote control or press the button on the unit when you reach
the desired point to resume normal playback.
Note:
• The DVD player mutes sound and subtitles during reverse and forward scan of DVDs.
• The fast playback speed may differ depending on the disc.
• Press the
NEXT button to advance titles, chapters/tracks.
• Press the
PREV button to go back to current or previous titles, chapters/tracks.
• For an Audio CD, use the number buttons on the remote control to go directly to the desired track
number.
Audio Selection
On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the
preferred language and sound system.
1. While a disc is playing, press the AUDIO button to show the current
Audio 1/3:Dolby D 2ch English
audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
Note:
• If only one audio format is recorded on the DVD, the number does not change.
• Some DVDs allow you to change audio selections using the disc menu only. If this is the case, press
the MENU button and choose the appropriate language on the disc menu.
• You can select different audio channels (Stereo, Mono Left, Mono Right or Mix-Mono) on an Audio
CD by pressing the AUDIO button repeatedly.
Subtitle Selection
1. While a DVD is playing, press the SUBTITLE button to display the current Subtitle 02/03:Spanish
language setting, as shown in the example.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles
off by pressing the SUBTITLE button repeatedly until the “ Subtitle Off ” is displayed.
Note:
• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear immediately after you select your desired scene.
• The number of subtitle languages recorded differs depending on the disc. If only one language is
recorded, the language does not change.
• This function can only be used for discs on which subtitles have been recorded in multiple
languages.
• Some DVDs allow you to change subtitles using the disc menu only. If this is the case, press the
MENU button and choose the appropriate subtitle on the disc menu.
Angle Selection
Some DVDs contain scenes that have been shot from a number of different angles. For these discs, the
same scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles recorded,
1/3
1
press the ANGLE button to view the number of current
Sequence of angle shots (Example)
angles available.
2. Press the ANGLE button repeatedly to change the scene to
the next recorded angle.
• After approx. two seconds, playback will continue from the
new angle selected.
• If no button is pressed within 10 seconds, playback continues without changing the current angle.
Note:
This function can only be used for discs on which scenes shot from multiple angles have been recorded.
1 /3
E-6
DRC99310K_ENGLISH IB 7pt_594x297mm.indd 2
Programmable Memory
You can combine your favorite titles/chapters/tracks and play them in the order you determine.
Adjust the LCD Screen
You can adjust Brightness, Screen Size and Contrast of the LCD screen.
1. Press the VIDEO MODE button.
2. Press the / button to select Brightness, Screen Size or Contrast.
3. Press the / button to change the setting.
4. Press the VIDEO MODE button to exit the menu.
1. During playback, press the MEMORY button and a
program screen appears.
Clear: Delete all input programs.
Exit: Exit memory menu and return to normal playback.
Start: Start memory playback.
Next / Prev: Move to the next / previous setup page.
Repeat Playback
You can play a specific DVD title or chapter repeatedly (title repeat, chapter repeat, A-B repeat).
Repeating a Chapter
1. While the DVD is playing, press the REPEAT DISC button until the “
the screen. The current chapter is played repeatedly.
Chapter
” indicator displays on
Repeating a Title
2. While the DVD is playing, press the REPEAT DISC button until the “
screen. The current title is played repeatedly.
Title
” indicator displays on the
To Resume Normal Playback
3. While the DVD is playing, press the REPEAT DISC button until the “
the screen.
Repeat Off
” indicator displays on
You can play a single CD track or the whole disc repeatedly.
Repeating a Single Track
1. While the CD is playing, press the REPEAT DISC button until the “
screen. The current track is played repeatedly.
” indicator displays on the
Repeating the Whole Disc
2. While the CD is playing, press the REPEAT DISC button until the “
screen. The whole disc is played repeatedly.
” indicator displays on the
To Resume Normal Playback
3. While the CD is playing, press the REPEAT DISC button until the “
the screen.
Repeat Off
” indicator displays on
Repeating a Specific Section
Skip (Forward / Reverse)
2 /3
3 /3
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (“
displayed) you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of the section (“
AB ” is displayed).
3. The unit will immediately begin replaying your selection.
2. Input the title (2 digits) and chapter (2 digits) by pressing the number buttons (for example: 01 02, 02
05, 02 11). It will move to the next item automatically.
• You can use the Cursor buttons ( , , , ) to move the highlighted bar to any item, and re-enter the
title and chapter. Press the
NEXT /
PREV to move to the next / previous setup page.
• You can use the Cursor buttons ( , , , ) to move the highlighted bar to “Clear”, “Exit”, “Start” or “Next
/ Prev”, and press the ENTER button to confirm.
3. Press the PLAY button on the remote control or
(“ Program ” appears on the screen).
button on the unit to start memory playback.
4. To resume normal playback from memory playback
1).Press the MEMORY button to display the memory menu.
2).Use the Cursor buttons ( , , , ) to move the highlighted bar to “Stop”. Press the ENTER button to
confirm “Stop”.
3).Use the Cursor buttons ( , , , ) to highlight “Clear”, and then press the ENTER button to confirm.
4).Use the Cursor buttons ( , , , ) to highlight “Exit”, and then press the ENTER button to confirm. It will
return to normal playback (“ Program ” disappears from the screen).
Notes:
• For a CD, you can only arrange order for tracks. The display will be a little different.
• If the title or chapter number entered is not permitted by the DVD, it will disappear. You should re-enter
correct number.
• You should input items one by one following the 1, 2, 3 ... sequence.
• If the DVD contains only one title, you can only arrange order for chapters.
• Some discs may not permit memory playback operation.
• If you select repeat during memory playback, the DVD player repeats the current memory playback.
• If you press the MEMORY button while the display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you press the STOP button two times, open the
disc tray or turn off the DVD player.
Video Setup
1. Press the SETUP button on the remote control or MENU
button on the unit in stop mode (when disc is not playing).
2. Press the / button to select Video Menu.
3. Press the / button to select the option (Brightness or
Contrast), then press the button.
4. Press the / button to adjust the setting, then press the
ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
Video
Language
System
Brightness
Contrast
00
00
CAUTION:
1. Do not use this DVD player case as a swing, car seat, or for any other purpose except to hold a DVD
player and accessories.
2. The DVD player case is intended for viewing only from the rear seats. Do not install or use this
product in the front seat of a vehicle.
3. To reduce the chance of injury in case of a collision or sudden stop:
• Always keep DVD player strapped securely inside case while vehicle is moving.
• Always keep DVD player case securely attached inside vehicle while the vehicle is moving.
4. Always position the plastic hooks and strap adjustment slider so that they do not touch the back of
the head of the person in the front seat.
Go To Video Menu
System Setup
1. Press the SETUP button on the remote control or MENU
button on the unit in stop mode (when disc is not playing).
2. Press the / button to select System Menu.
3. Press the / button to select the option (TV Display or
Default), then press the button.
4. Press the / button to adjust the settings, then press the
ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
Video
Language
System
- - System Menu - TV Display
Default
Wide
No
Go To System Menu
TV Display
Pan Scan
Cut off when a wide • When wide-screen video is played, this mode clips the right and left sides screen video image is
of the image so that it can be viewed on a conventional screen.
played.
• Some wide-screen DVDs that do not permit Pan Scan mode playback are
automatically played in letterbox mode (black bands that appear at the top and
bottom of the screen).
Letter Box
• When wide-screen video is played in this mode on a conventional screen, black
bands appear at the top and bottom of the screen.
Pan Scan
Wide Screen
• This is the correct mode for playing wide-screen videos on the unit screen or other
external wide-screens.
Notes:
• The displayable picture size is preset on the DVD. Therefore the playback picture of
some DVDs may not conform to the picture size selected.
• When you play DVDs recorded in the 4:3 aspect ratio, the playback picture will
Letter Box
always appear in the 4:3 aspect ratio regardless of the TV display setting.
• Select Wide Screen to conform the LCD screen on the unit. Always be sure that
your TV display conforms to the actual TV in use if you connect the unit to a TV.
Default
It takes 3-5 seconds to reset the DVD settings to the factory default.
Wide Screen
Viewing JPEG Files
A
 ” is
To Resume Normal Playback
AB OFF ” indicator displays on the
4. While the disc is playing, press the REPEAT A-B button until the “
screen (the repeat indicator disappears from the screen for a CD). The system will return to normal
playback.
Notes:
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that includes multiple camera angles.
• You can specify a segment only within the current title or track.
• There may be a slight difference between point A and the location where playback actually resumes
depending on the disc.
Locating a Desired Section
This unit can play JPEG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommended).
Viewing JPEG Files
1. Press the OPEN knob to open the disc door.
2. Hold a JPEG file disc by its edges and gently push it onto the
spindle with the label side facing up until you hear a “click”.
3. Close the disc door. The JPEG files on the disc will be
displayed one by one automatically. If the disc does not play
automatically, press the / button to select a file and
press the  PLAY button on the remote control or button
on the unit.
4. Press the MENU or STOP button to display a folder list. Press the / button to highlight a
JPEG file to play. Press the  PLAY button on the remote control or button on the unit to start
playback. Notes:
• You can press the PAUSE button on the remote control or button on the unit to freeze the picture.
Press the PLAY button on the remote control or button on the unit to resume picture slide show.
• You can press the STOP button to quit playback.
• You can press the
PREV or
NEXT button to change the picture.
• You can press the ANGLE button to rotate direction of the picture by 90°.
• Some discs may not permit this operation.
Locating a Specific Chapter / Title
If you know the chapter/title number for the chapter/title that you want to play, you can locate it by
directly selecting that number.
Title 01/03 Chapter 03/12
Title 01/03 Chapter 00/00
1. Press the GOTO button. /
2. Press the / button to highlight chapter/title number, then press the corresponding number
buttons (2 digits) for the chapter/title you want (for example: 02, 08, 10 or 15). If you press only 1
numeric button, press the ENTER button to confirm.
3. Playback starts from the selected chapter/title.
Note:
• If the chapter/title number entered is not permitted by the DVD, “ Input invalid ” will display. Repeat
steps 1 and 2 to re-enter the correct number.
• Some discs may not respond to this process.
• This method of locating a chapter/title is available only on a DVD that contains chapter/title
numbers.
Customizing the Function Settings
Language Setup
2. Press the corresponding number buttons (5 digits: X:XX:XX, for example: 0 30 05, 1 08 23, 1 22 56) for
the setting point you want.
3. Playback starts from the selected section.
Notes:
• If the time entered is not permitted by the DVD, “ Input invalid ” will display. You should re-enter the
correct time.
• Some discs may not respond to this process.
1. Press the SETUP button on the remote control or MENU
Video
System
Language
button on the unit in stop mode (when disc is not playing).
- - Language Menu - 2. Press the button to select Language Menu.
Eng
Player Menu
Eng
Audio
3. Press the / button to select the option (Player Menu,
Off
Subtitle
Audio, Subtitle or Disc Menu), then press the button.
Eng
Disc Menu
4. Press the / button to select your preferred language,
then press the ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
Go To Language Menu
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
Notes:
• Some DVDs may not play in the audio language you selected. A prior language may be programmed
on the disc.
• Some DVDs may be set to display subtitles in a language other than the one you selected. A prior
subtitle language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections using the disc menu only. If this is the case, press the MENU button and choose the appropriate subtitle language from the selection on the disc
menu.
• Some DVDs may not include your pre-selected language. In this case, the DVD player automatically
displays disc menus consistent with the disc’s initial language setting.
E-7
E-8
Locating a Specific Time
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button two times. Title 01/03 Time : :
Carrying Bag Installation
- - Video Menu - -
Sound System
Dolby Digital
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for twochannel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multichannel soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Maintenance
To Attach the DVD Player Case to a Headrest (Images 1 & 2)
1. Insert the DVD player into the case as shown right (1, 2, 3).
2. Unzip the main compartment that holds the player; locate the D
rings at the top of the case (A).
3. Locate 2 straps with hooks on each end.
4. Hook one end of the each strap to the D rings at the top of the
case.
5. Criss-cross the straps around the front of the headrest (B) and
hook the straps to a second set of rings on the lower part of the
case (C).
6. Tighten up the straps until the unit is secured. Connect the 12V
car adapter as shown on the right (D).
7. Connect headphone splitter (for earphone) as shown on the
right (E).
3
1
Images 1
CAUTION:
1. High temperature damages CDs/DVDs.
2. Do not store in closed cars.
3. Protect from direct sunlight.
Troubleshooting Guide
Symptom
Cause (and remedy)
No power.
• Ensure the AC power adapter is connected.
• The unit is not turned on.
The remote
control does
not function.
• Make sure the infrared remote sensor is not blocked.
• Make sure the plastic sheet has been removed from the remote control.
• Point the remote directly at the infrared remote sensor on the unit.
• Replace the battery in the remote control with a new one.
No sound or
• The volume control is located on the side of the unit – please try adjusting this.
only a very
• The system is in pause mode. Press the button to return to normal play mode.
low-level
• The unit is in fast-forward or fast-reverse mode. Press the PLAY button on remote
sound is heard.
control to return to normal play mode.
• Make sure the AUDIO/VIDEO output connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• The unit is too hot; shut off the unit for 30 minutes to cool it down.
No picture.
• The region number of the disc doesn't match the region
number of this unit.
The picture is
not clear.
• Clean the disc.
• The disc is scratched.
• Adjust the LCD's brightness and contrast using the VIDEO MODE button on the
remote control.
Severe hum or
noise is heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
The disc does
not play.
•
•
•
•
Cleaning the Unit
• Be sure to turn the unit off and disconnect the AC power adapter before cleaning the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that
has been dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry
cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to
remove dust.
2
Note: Before closing the bag, release the left and right elastic bands
from the screen panel.
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a
cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause
malfunctions.
Images 1
There is no disc inside (“No Disc” appears on the screen).
Insert the disc correctly with the playback side facing down.
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc region number are
incompatible.
• Condensation may have formed inside the unit due to a sudden change in
temperature. Wait about an hour for it to clear and try again.
Specifications and external appearance are subject to change without notice.
Need More Help?
Please visit online help at http://www.RCAav.com
Important Note
• Before transporting the unit, remove the disc from the disc compartment.
E-9
Printed in China
811-931091W040
2010-6-18 16:17:12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement