Data Sheet

HFBR-53A5VEM/HFBR-53A5VFM

3.3 V 1 x 9 Fiber Optic Transceivers for Gigabit Ethernet Low Voltage

Data Sheet

Description

The HFBR-53A5VM transceivers from Avago Technologies allow the system designer to implement a range of solutions for multimode Gigabit Ethernet applications.

The overall Avago transceiver prod uct consists of three sections: the transmitter and receiver optical subassemblies, an electrical subassembly, and the package housing which incorporates a duplex SC connector receptacle.

Transmitter Section

The transmitter section of the HFBR-53A5VEM/FM consists of an 850 nm Vertical Cavity Surface Emitting Laser (VCSEL) in an optical subassembly (OSA), which mates to the fiber cable. The OSA is driven by a custom, silicon bipolar IC which converts differential PECL compatible logic signals into an analog laser diode drive current. The high speed output lines are internally AC-coupled and differentially terminate with a 100

resistor.

Receiver Section

The receiver of the HFBR-53A5VEM/FM includes a GaAs

PIN photo-diode mounted together with a custom, silicon bipolar transimpedance preamplifier IC in an OSA.

This OSA is mated to a custom silicon bipolar circuit that provides post-amplification and quantization.

The post-amplifier also includes a Signal Detect circuit which pro vides a TTL logic-high output upon detection of a usable input optical signal level. The high speed output lines are internally AC-coupled.

Features

Compliant with specifications for IEEE- 802.3z Gigabit

Ethernet

Industry standard mezzanine height 1 x 9 package style with integral duplex SC connector

Performance

– HFBR-53A5VEM/FM:

220 m links in 62.5/125

µ m MMF 160 MHz* km cables

275 m links in 62.5/125

µ m MMF 200 MHz* km cables

500 m links in 50/125

µ m MMF 400 MHz* km cables

550 m links in 50/125

µ m MMF 500 MHz* km cables

IEC 60825-1 Class 1/CDRH Class I laser eye safe

Single +3.3 V power supply operation with PECL compatible logic interfaces and TTL Signal Detect

Wave solder and aqueous wash process compatible

Applications

Switch to switch interface

Switched backbone applications

High speed interface for file servers

High performance desktops

Related Products

• Physical layer ICs available for optical or copper interface (HDMP-1636A/1646A)

• Quad Serdes IC available for high-density interface

• Versions of this transceiver module also available for

+5 V operation (HFBR/HFCT-53D5)

• MT-RJ SFF fiber optic transceivers for Gigabit Ethernet

(HFBR/HFCT-5912E)

• Gigabit Interface Converters (GBIC) Gigabit Ethernet

SX-HFBR-5601 / LX-HFCT-5611

Package and Handling Instructions

Flammability

The HFBR-53A5VEM/FM transceiver housing is made of high strength, heat resistant, chemically resistant, and UL

94V-0 flame retardant plastic.

Recommended Solder and Wash Process

The HFBR-53A5VEM/FM is compatible with industry- standard wave or hand solder processes.

Process Plug

This transceiver is supplied with a process plug (HFBR-

5000) for protection of the optical ports within the duplex

SC connector receptacle. This process plug prevents contamination during wave solder and aqueous rinse as well as during handling, shipping and storage. It is made of a high-temperature, molded sealing material that can withstand 80° C and a rinse pressure of 110 lbs per square inch.

Recommended Solder Fluxes

Solder fluxes used with the HFBR-53A5VEM/FM should be water-soluble, organic fluxes. Recom mended solder fluxes include Lonco 3355-11 from London Chemical

West, Inc. of Burbank, CA, and 100 Flux from Alpha-Metals of Jersey City, NJ.

Recommended Cleaning/Degrading Chemicals

Alcohols:

methyl, isopropyl, isobutyl.

Aliphatics:

hexane, heptane.

Other:

soap solution, naphtha.

Do not use partially halogenated hydrocarbons such as 1,1.1 trichloroethane, ketones such as MEK, acetone, chloroform, ethyl acetate, methylene dichloride, phenol, methylene chloride, or N-methylpyrolldone. Also, Avago does not recommend the use of cleaners that use halogenated hydrocarbons because of their potential environmental harm.

Regulatory Compliance

(See the Regulatory Compliance Table for transceiver performance)

The overall equipment design will determine the certification level. The transceiver performance is offered as a figure of merit to assist the designer in considering their use in equipment designs.

Electrostatic Discharge (ESD)

There are two design cases in which immunity to ESD damage is important.

The first case is during handling of the transceiver prior to mounting it on the circuit board. It is important to use normal ESD handling precautions for ESD sensitive devices. These pre cautions include using grounded wrist straps, work benches, and floor mats in ESD controlled areas. The transceiver perform ance has been shown to provide adequate performance in typical industry production environments.

The second case to consider is static discharges to the exterior of the equipment chassis containing the transceiver parts. To the extent that the duplex SC connector receptacle is exposed to the outside of the equipment chassis it may be subject to whatever system-level ESD test criteria that the equipment is intended to meet.

The transceiver performance is more robust than typical industry equipment requirements of today.

Electromagnetic Interference (EMI)

Most equipment designs utilizing these high-speed transceivers from Avago will be required to meet the requirements of FCC in the United States, CENELEC EN55022

(CISPR 22) in Europe and VCCI in Japan. Refer to EMI section (page 4) for more details.

Immunity

Equipment utilizing these transceivers will be subject to radio-frequency electromagnetic fields in some environments. These transceivers have good immunity to such fields due to their shielded design.

Eye Safety

These laser-based transceivers are classified as AEL Class

I (U.S. 21 CFR(J) and AEL Class 1 per EN 60825-1 (+A11).

They are eye safe when used within the data sheet limits per CDRH. They are also eye safe under normal operating conditions and under all reasonably forseeable single fault conditions per EN60825-1. Avago has tested the transceiver design for compliance with the requirements listed below under normal operating conditions and under single fault conditions where applicable. TUV

Rheinland has granted certification to these transceivers for laser eye safety and use in EN 60950 and EN 60825-2 applications. Their performance enables the transceivers to be used without concern for eye safety up to maximum volts transmitter V

CC

.

2

CAUTION:

There are no user serviceable parts nor any maintenance required for the HFBR-53A5VEM/FM. All adjustments are made at the factory before shipment to our customers.

Tampering with or modifying the performance of the

HFBR-53A5VEM/FM will result in voided product warranty.

It may also result in improper operation of the HFBR-

53A5VEM/FM circuitry, and possible overstress of the laser source. Device degradation or product failure may result.

Connection of the HFBR-53A5VEM/FM to a non approved optical source, operating above the recom absolute maximum conditions or operating the HFBR-

53A5VEM/FM in a manner inconsistent with its design and function may result in hazardous radiation exposure and may be considered an act of modifying or manufacturing a laser product. The person(s) performing such an act is required by law to recertify and reidentify the laser product under the provisions of U.S. 21 CFR (Subchapter J).

Regulatory Compliance

Feature

Electrostatic Discharge

(ESD) to the Electrical Pins

Electrostatic Discharge

(ESD) to the

Duplex SC Receptacle

Electromagnetic

Interference (EMI)

Immunity

Laser Eye Safety and

Equipment Type Testing

Component Recognition

Test Method

MIL-STD-883C

Method 3015.4

Variation of IEC 801-2

Targeted Performance

Class 1 (> 1500 V).

Typically withstand at least 15 kV without damage when the duplex SC connector receptacle is contacted by a Human Body

Model probe.

Margins are dependent on customer board and chassis designs.

FCC Class B

CENELEC EN55022 Class B

(CISPR 22A)

VCCI Class 1

Variation of IEC 801-3

US 21 CFR, Subchapter J per Paragraphs 1002.10 and 1002.12

EN 60825-1: 1994 + A11:1996

EN 60825-2: 1994 + A1

EN 60950: 1992 + A1 + A2

+ A3 + A4 + A11

Underwriters Laboratories and Canadian Standards

Association Joint Component

Recognition for Information

Technology Equipment

Including Electrical Business

Equipment.

Typically show no measurable effect from a 10 V/m field swept from 27 to 1000 MHz applied to the transceiver without a chassis enclosure.

AEL Class I, FDA/CDRH

HFBR-53A5V*M Accession #9720151

AEL Class 1, TUV Rheinland of North America HFBR-53A5V*M:

Certificate #R9771018.5

Protection Class III

UL File E173874

3

APPLICATION SUPPORT

Optical Power Budget and Link Penalties

The worst-case Optical Power Budget (OPB) in dB for a fiber-optic link is determined by the difference between the minimum transmitter output optical power (dBm avg) and the lowest receiver sensitivity (dBm avg). This OPB provides the necessary optical signal range to establish a working fiber-optic link. The OPB is allocated for the fiberoptic cable length and the corre sponding link penalties.

For proper link performance, all penalties that affect the link performance must be accounted for within the link optical power budget. The Gigabit Ethernet IEEE 802.3z standard identifies, and has modeled, the contributions of these OPB penalties to establish the link length requirements for 62.5/125

µ m and 50/125

µ m multimode fiber usage. Refer to the IEEE 802.3z standard and its supplemental documents that develop the model, empirical results and final specifications.

Data Line Interconnections

Avago’s HFBR-53A5VEM/FM fiber-optic transceiver is designed for compatible PECL signals. The transmitter inputs are internally AC-coupled to the laser driver circuit from the transmitter input pins (pins 7, 8). The transmitter driver circuit for the laser light source is an AC-coupled circuit. This circuit regulates the output optical power. The regulated light output will maintain a constant output optical power provided the data pattern is reasonably balanced in duty factor. If the data duty factor has long, con tinu ous state times (low or high data duty factor), then the output optical power will gradually change its average output optical power level to its pre-set value.

The receiver section is internally AC-coupled between the pre-amplifier and the post-amplifier stages. The actual

Data and Data-bar outputs of the post-amplifier are

AC-coupled to their respective output pins (pins 2, 3).

Signal Detect is a single-ended, TTL output signal that is

DC-coupled to pin 4 of the module. Signal Detect should not be AC-coupled externally to the follow-on circuits because of its infrequent state changes.

Caution should be taken to account for the proper intercon nec tion between the supporting Physical Layer integrated circuits and this HFBR-53A5VEM/FM transceiver.

Figure 3 illustrates a recommended interface circuit for interconnecting to a DC PECL compatible fiber-optic transceiver.

Eye Safety Circuit

For an optical transmitter device to be eye-safe in the event of a single fault failure, the trans mit ter must either maintain normal, eye-safe operation or be disabled.

In the HFBR-53A5VEM/FM there are three key elements to the laser driver safety circuitry: a monitor diode, a window detec tor circuit, and direct control of the laser bias. The window detection circuit monitors the average optical power using the monitor diode. If a fault occurs such that the transmitter DC regulation circuit cannot maintain the preset bias conditions for the laser emitter within ±20%, the transmitter will automatically be disabled. Once this has occurred, only an electrical power reset will allow an attempted turn-on of the transmitter.

Signal Detect

The Signal Detect circuit provides a deasserted output signal that implies the link is open or the transmitter is OFF as defined by the Gigabit Ethernet specification

IEEE 802.3z, Table 38.1. The Signal Detect threshold is set to transition from a high to low state between the minimum receiver input optional power and -30 dBm avg. input optical power indicating a definite optical fault

(e.g., unplugged connector for the receiver or transmitter, broken fiber, or failed far-end transmitter or data source).

A Signal Detect indicating a working link is functional when receiving encoded 8B/10B characters. The Signal

Detect does not detect receiver data error or error-rate.

Data errors are determined by Signal processing following the transceiver.

Electromagnetic Interference (EMI)

One of a circuit board designer’s foremost concerns is the control of electromagnetic emissions from electronic equipment. Success in controlling generated Electromagnetic Interference (EMI) enables the designer to pass a governmental agency’s EMI regulatory standard; and more importantly, it reduces the possibility of interference to neighboring equipment. The EMI performance of an enclosure using these transceivers is dependent on the chassis design. Avago encourages using standard RF suppression practices and avoiding poorly EMI-sealed enclosures.

4

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed that limiting values of more than one parameter can be applied to the product at the same time. Exposure to the absolute maximum ratings for extended periods can adversely affect device reliability.

Typ.

Reference Parameter

Storage Temperature

Supply Voltage

Transmitter Differential Input Voltage

Relative Humidity

TTL Signal Detect Current – Low

TTL Signal Detect Current – High

Symbol

T

S

V

CC

V

D

RH

I

OL, MAX

I

OH, MAX

5

-5

Min.

-40

-0.5

Max.

+100

5.0

2.2

95

4.0

Units

V

%

°C

V mA mA

1

Recommended Operating Conditions

Parameter

Ambient Operating Temperature

Case Temperature

Supply Voltage

Power Supply Rejection

Transmitter Differential Input Voltage

Data Output Load

TTL Signal Detect Output Current

TTL Signal Detect Output Current

V

D

R

DL

I

OL

I

OH

Symbol

T

A

T

C

V

CC

PSR

-400

Min.

0

3.14

0.4

Typ.

3.3

100

50

1.6

1.0

Max.

70

80

3.47

Units

°C

°C

V mV p-p

V

Ω mA

µ A

Reference

2

3

Process Compatibility

Parameter Symbol Min.

Typ.

Max.

Units Reference

Hand Lead Soldering Temperature/Time

Wave Soldering and Aqyeous Wash

T

SOLD/

T

SOLD

T

SOLD/

T

SOLD

+260/10

+260/10

°C/s

°C/s 4

Notes:

1. The transceiver is class 1 eye safe up to V

CC

= 5.0 V.

2. Case temperature measurement referenced to the center top of the internal metal transmitter shield.

3. Tested with a 100 mV

P–P

sinusoidal signal in the frequency range from 10 Hz to 2 MHz on the V

CC filter in place. Typically less than a 1 dB change in sensitivity is experienced.

4. Aqueous wash pressure < 110 psi.

supply with the recommended power supply

5

HFBR-53A5VEM/FM, 850 nm VCSEL

Transmitter Electrical Characteristics

(T

A

= 0° C to +70° C, V

CC

= 3.14 V to 3.47 V)

Parameter

Supply Current

Power Dissipation

Laser Reset Voltage

Symbol

I

CCT

P

DIST

V

CCT-reset

Min.

Typ.

55

0.18

2.5

Max.

75

0.26

2.0

Units

mA

V

Reference

1

Receiver Electrical Characteristics

(T

A

= 0° C to +70° C, V

CC

= 3.14 V to 3.47 V)

Parameter

Supply Current

Power Dissipation

Symbol

I

CCR

P

DISR

V

OPP

Min.

Typ.

80

0.26

Max.

135

0.47

Units

mA

Reference

Data Output Voltage – Peak to Peak

Differential

0.4

1.20

V 2

Data Output Rise Time

Data Output Fall Time

Signal Detect Output Voltage – Low

Signal Detect Output Voltage – High

Signal Detect Assert Time

Signal Detect Deassert Yime t r t f

V

OL

V

OH t

SDA t

SDD

2.2

0.40

0.40

0.6

100

350 ns ns

V

V

µ

µ s s

3

3

4

4

Notes:

1. The Laser Reset Voltage is the voltage level below which the V

CCT

voltage must be lowered to cause the laser driver circuit to reset from an electrical/optical shutdown condition to a proper electrical/optical operating condition. The maximum value corresponds to the worst-case highest V

CC

voltage necessary to cause a reset condition to occur. The laser safety shutdown circuit will operate properly with transmitter V

CC levels of 2.5 Vdc ≤ V

CC

≤ 5.0 Vdc.

2. These outputs are compatible with 10 K, 10 KH, and 100 K ECL and PECL inputs.

3. These are 20-80% values.

4. Under recommended operating conditions.

6

HFBR-53A5VEM/FM, 850 nm VCSEL

Transceiver Optical Characteristics

(T

A

= 0° C to +70° C, V

CC

= 3.14 V to 3.47 V)

Parameter

Output Optical Power

50/125

µ m, NA = 0.20 fiber

Output Optical Power

62.5/125

µ m, NA = 0.275 fiber

Optical Extinction Ratio

Center Wavelength

Spectral Width – rms

Optical Rise/Fall Time

RIN

12

Coupled Power Ratio

Total Transmitter Jitter Added at TP2

Symbol

P

OUT

P

OUT l

C

σ t r

/ t f

CPR

Min.

-9.5

-9.5

9

830

9

Typ.

850

Max.

-4

-4

860

0.85

0.26

-117

227

Unit

dBm avg.

dBm avg.

dB nm nm rms ns dB/Hz dB ps

Reference

1

1

2

3, 4, Figure 1

5

6

Receiver Optical Characteristics

(T

A

= 0° C to +70° C, V

CC

= 3.14 V to 3.47 V)

Parameter Symbol Min.

Typ.

Max.

Unit Reference

Input Optical Power

Stressed Receiver Sensitivity

P

IN

62.5

µ m

50 µ m

-17 0

-12.5

-13.5

dBm avg.

dBm avg.

dBm avg.

7

8

8

Stressed Receiver Eye Opeing at TP4

Receive Electrical 3 dB

Upper Cutoff Frequency

201

1500 ps

MHz

6, 9

10

Operating Center Wavelength

Return Loss l

C

770

12

860 nm dB 11

Signal Detect – Asserted

Signal Detect – Deasserted

Signal Detect – Hysteresis

P

A

P

D

P

A

– P

D

-30

1.5

-17 dBm avg.

dBm avg.

dB

12

12

12

Notes:

1. The maximum Optical Output Power complies with the IEEE 802.3z specification, and is class 1 laser eye safe.

2. Optical Extinction Ratio is defined as the ratio of the average optical power of the transmitter in the high (“1”) state to the low (“0”) state. Extinction

Ratio shall be measured using the methods specified in TIA/EIA.526.4A. This measurement may be made with the node transmitting a 36A.3 data pattern. The Saturation Ratio is measured under fully modulated conditions with worst case reflections. A36A.3 data pattern is a repeating K28.7 data pattern which generates a 125 mHz square wave.

3. These are unfiltered 20-80% values.

4. Laser transmitter pulse response characteristics are specified by an eye diagram (Figure 1). The characteristics include rise time, fall time, pulse overshoot, pulse undershoot, and ringing, all of which are controlled to prevent excessive degradation of the receiver sensitivity. These parameters are specified by the referenced Gigabit Ethernet eye diagram using the required filter. The output optical waveform complies with the requirements of the eye mask discussed in section 38.6.5 and Fig. 38-2 of IEEE 802.3z.

5. CPR is measured in accordance with EIA/TIA-526-14A as referenced in 802.3z, section 38.6.10.

6. TP refers to the compliance point specified in 802.3z, section 38.2.1.

7. The receive sensitivity is measured using a worst case extinction ratio penalty while sampling at the center of the eye.

8. The stressed receiver sensitivity is measured using the conformance test signal defined in 802.3z, section 38.6.11. The conformance test signal is conditioned by applying deterministic jitter and intersymbol interference.

9. The stressed receiver jitter is measured using the conformance test signal defined in 802.3z, section 38.6.11 and set to an average optical power

0.5 dB greater than the specified stressed receiver sensitivity.

10. The 3 dB electrical bandwidth of the receiver is measured using the technique outlined in 802.3z, section 38.6.12.

11. Return loss is defined as the minimum attenuation (dB) of received optical power for energy reflected back into the optical fiber.

12. With valid 8B/10B encoded data.

7

Pin Symbol

Mounting Pins

1

2

3

4

5

6

7

8

9

V

EER

RD+

RD-

SD

V

CCR

V

CCT

TD-

TD+

V

EET

Functional Description

The mounting pins are provided for transceiver mechanical attachment to the circuit board. They are embedded in the nonconductive plastic housing and are not connected to the transceiver internal circuit, nor is there a guaranteed connection to the metallized housing in the EM and FM versions. They should be soldered into plated-through holes on the printed circuit board.

Receiver Signal Ground

Directly connect this pin to receiver signal ground plane. (For HFBR-53A5VM, V

EER

= V

EET

)

Receiver Data Out

AC coupled – PECL compatible.

Receiver Data Out Bar

AC coupled – PECL compatible.

Signal Detect

Signal Detect is a single-ended TTL output. If Signal Detect output is not used, leave it open-circuited.

Normal optical input levels to the receiver result in a logic “1” output, V

OH

, asserted.

Low input optical levels to the receiver result in a fault condition indicated by a logic “0” output V

OL

, deasserted.

Receiver Power Supply

Provide +3.3 Vdc via the recommended receiver power supply filter circuit.

Locate the power supply filter circuit as close as possible to the V

CCR

pin.

Transmitter Power Supply

Provide +3.3 Vdc via the recommended transmitter power supply filter circuit.

Locate the power supply filter circuit as close as possible to the V

CCT

pin.

Transmitter Data In-Bar

AC coupled – PECL compatible. Internally terminated differentially with 100

.

Transmitter Data In

AC coupled – PECL compatible. Internally terminated differentially with 100

.

Transmitter Signal Ground

Directly connect this pin to the transmitter signal ground plane.

1.3

1.0

0.8

0.5

0.2

0

-0.2

0 0.22

0.375

0.625

NORMALIZED TIME

Figure 1. Transmitter Optical Eye Diagram Mask.

0.78

1.0

1 = V

EER

2 = RD+

3 = RD-

4 = SD

5 = V

CCR

6 = V

CCT

7 = TD-

8 = TD+

9 = V

EET

NIC

NIC

RX

TX

TOP VIEW

NIC = NO INTERNAL CONNECTION (MOUNTING PINS)

Figure 2. Pin-Out.

HFBR-53V5 fig 2 - Pinout

HFBR-53V5 fig 1

8

+

3.3 Vdc

GND

LASER

DRIVER

CIRCUIT

PECL

INPUT

HFBR-53A5VEM/FM

FIBER-OPTIC

TRANSCEIVER

SIGNAL

DETECT

CIRCUIT

V

EET

9

8

100

TD+

TD-

7

V

CCT

6

C2

0.1 µF

V

CCR

5

C1

0.1

µF

L2

1 µH

L1

+

C8*

10 µF*

1 µH

50

50

C3

0.1

µF

0.1

µF

3.3 V

R13

150

R12

150

V

CC2

TD+

V

EE2

OUTPUT

DRIVER

TD-

+

C4

10

µF

CLOCK

SYNTHESIS

CIRCUIT

PARALLEL

TO SERIAL

CIRCUIT

HDMP-1636A/-1646A

SERIAL/DE-SERIALIZER

(SERDES - 10 BIT

TRANSCEIVER)

SD

4 TO SIGNAL DETECT (SD)

INPUT AT UPPER-LEVEL-IC

PRE-

AMPLIFIER

POST-

AMPLIFIER

RD3

RD+

V

EER

2

1

50

50

R14

100

RD-

RD+

INPUT

BUFFER

CLOCK

RECOVERY

CIRCUIT

SERIAL TO

PARALLEL

CIRCUIT

SEE HDMP-1636A/-1646A DATA SHEET FOR

DETAILS ABOUT THIS TRANSCEIVER IC.

NOTES:

USE SURFACE-MOUNT COMPONENTS FOR OPTIMUM HIGH-FREQUENCY PERFORMANCE.

USE 50

MICROSTRIP OR STRIPLINE FOR SIGNAL PATHS.

LOCATE 50

TERMINATIONS AT THE INPUTS OF RECEIVING UNITS.

Figure 3. Recommended Gigabit/sec Ethernet HFBR-53A5VEM/FM Fiber-Optic Transceiver and HDMP-1636A/1646A SERDES Integrated Circuit Transceiver

Interface and Power Supply Filter Circuits.

20.32

0.800

(2X) ø

1.9 ± 0.1

0.075 ± 0.004

Ø0.000

M

A

–A–

20.32

0.800

(9X) ø

0.8 ± 0.1

0.032 ± 0.004

Ø0.000

M

A

TOP VIEW

Figure 4. Recommended Board Layout Hole Pattern.

HFBR-53V5 fig 4 - Layout Hole Pattern

9

25.4

(1.00)MAX.

(

0.25

+0.1

-0.05

0.010

+0.004

-0.002

)

9.8

(0.386)MAX.

3.3 ± 0.38

(0.130 ± 0.015)

9X

(

0.46

+0.25

-0.05

0.018

+0.010

-0.002

)

20.32

(0.800)

23.8

(0.937)

20.32

(0.800)

8X

2.54

(0.100)

39.6

(1.56) MAX.

SLOT DEPTH

2.5

(0.10)

A

TX

XXXX-XXXX

ZZZZZ LASER PROD

21CFR(J) CLASS 1

COUNTRY OF ORIGIN YYWW

RX

KEY:

YYWW = DATE CODE

FOR MULTIMODE MODULE:

XXXX-XXXX = HFBR-53xx

ZZZZ = 850 nm

12.7

(0.50)

4.7

(0.185)

AREA

RESERVED

FOR

PROCESS

PLUG

12.7

(0.50)

SLOT WIDTH

2.0 ± 0.1

(0.079 ± 0.004)

0.51

(0.020)

15.8 ± 0.15

(0.622 ± 0.006)

2X

(

1.27

+0.25

-0.05

0.050

+0.010

-0.002

)

20.32

(0.800)

2X

1.3

(0.051)

DIMENSIONS ARE IN MILLIMETERS (INCHES).

ALL DIMENSIONS ARE ± 0.025 mm UNLESS OTHERWISE SPECIFIED.

Figure 5. Package Outline for HFBR-53A5VEM.

HFBR-5305 Pkg Dimen

10

1.014

2x

0.8

(0.032)

2x

0.8

(0.032)

10.9

(

0.43

+ 0.5

– 0.25

+ 0.02

– 0.01

)

9.4

(0.374)

5.35

(0.25)

MODULE

PROTRUSION

27.4 ± 0.50

(1.08 ± 0.02)

PCB BOTTOM VIEW

Figure 6. Suggested Module Positioning and Panel Cut-out for HFBR-53A5VEM.

HFBR-5305E Module

11

A

TX

XXXX-XXXX

ZZZZZ LASER PROD

21CFR(J) CLASS 1

COUNTRY OF ORIGIN YYWW

RX

KEY:

YYWW = DATE CODE

FOR MULTIMODE MODULE:

XXXX-XXXX = HFBR-53xx

ZZZZ = 850 nm

39.6

(1.56) MAX.

25.4

(1.00)MAX.

10.2

(0.40)

MAX.

12.7

(0.50)

29.6

(1.16)

UNCOMPRESSED

4.7

(0.185)

AREA

RESERVED

FOR

PROCESS

PLUG

12.7

(0.50)

SLOT WIDTH

2.0 ± 0.1

(0.079 ± 0.004)

2.09

(0.08)

UNCOMPRESSED

(

0.25

+0.1

-0.05

0.010

+0.004

-0.002

)

9.8

(0.386)MAX.

3.3 ± 0.38

(0.130 ± 0.015)

9X

(

0.46

+0.25

-0.05

0.018

+0.010

-0.002

)

20.32

(0.80)

1.3

(0.05)

15.8 ± 0.15

(0.622 ± 0.006)

2X

(

1.27

+0.25

-0.05

0.050

+0.010

-0.002

)

23.8

(0.937)

20.32

(0.800)

20.32

(0.800)

2X

1.3

(0.051)

DIMENSIONS ARE IN MILLIMETERS (INCHES).

ALL DIMENSIONS ARE ± 0.025 mm UNLESS OTHERWISE SPECIFIED.

Figure 7. Package Outline for HFBR-53A5VFM.

HFBR-5305E Pkg Dimen

12

A

TX

XXXX-XXXX

ZZZZZ LASER PROD

21CFR(J) CLASS 1

COUNTRY OF ORIGIN YYWW

RX

KEY:

YYWW = DATE CODE

FOR MULTIMODE MODULE:

XXXX-XXXX = HFBR-53xx

ZZZZ = 850 nm

39.6

(1.56)MAX.

1.01

(0.40)

12.7

(0.50)

25.4

(1.00)MAX.

AREA

RESERVED

FOR

PROCESS

PLUG

29.7

(1.17)

4.7

(0.185)

12.7

(0.50)

(

0.25

+0.1

-0.05

0.010

+0.004

-0.002

)

25.8

(1.02)

MAX.

10.2

(0.40)

MAX.

SLOT DEPTH

2.2

(0.09)

SLOT WIDTH

2.0 ± 0.1

(0.079 ± 0.004)

14.4

(0.57)

3.3 ± 0.38

(0.130 ± 0.015)

9x

(

0.46

+0.25

-0.05

0.018

+0.010

-0.002

)

9.8

(0.386)

MAX.

20.32

(0.800)

22.0

(0.87)

23.8

(0.937)

20.32

(0.800)

8x

2.54

(0.100)

15.8 ± 0.15

(0.622 ± 0.006)

2x

(

1.27

+0.25

-0.05

0.050

+0.010

-0.002

)

AREA

RESERVED

FOR

PROCESS

PLUG

20.32

(0.800)

2x

1.3

(0.051)

DIMENSIONS ARE IN MILLIMETERS (INCHES).

ALL DIMENSIONS ARE ± 0.025 mm UNLESS OTHERWISE SPECIFIED.

Figure 8. Suggested Module Positioning and Panel Cut-out for HFBR-53A5VFM.

Ordering Information

850 nm VCSEL

HFBR-53A5VEM

HFBR-53A5VFM

(SX – Short Wavelength Laser)

Extended shield, metal housing.

Flush shield, metal housing.

For product information and a complete list of distributors, please go to our web site:

www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.

Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved.

5988-0968EN - July 10, 2013

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement