Rheem | R801P | Specification Sheet | Rheem R801P Specification Sheet

Rheem R801P Specification Sheet
Air
Gas Furnaces
R801P (UF/HZ) Series
Rheem Classic® Series
Upflow/Horizontal Gas Furnace
R801P- Upflow/Horizontal Series
80% A.F.U.E.†
Input Rates 50-150 kBTU
✝ A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with
Department of Energy test procedures.
80% residential Gas Furnace CSA certified
3 way multi poise design UF / HZ
PlusOne™ Diagnostics — 7 Segment LED all units
PlusOne™ Ignition System – DSI for reliability and longevity
Heat exchanger is removable for improved serviceability.
Aluminized steel construction provides maximum corrosion
resistance and thermal fatigue reliability.
• Solid doors provide quiet operation
• Solid bottom
• Insulated blower compartment
•
•
•
•
•
• Low profile 34" cabinet ideal for space constrained
installations
• Blower shelf design – serviceable in all furnace orientations
• Hemmed edges on cabinets and doors
• 1/4 turn door knobs for tool less access
• Integrated Control board features dip switches for easy
system set up
• QR code for quick access to product information from your
smart phone or tablet
FORM NO. G11-543 REV. 2
Air
Table of Contents
R801P (UF/HZ) Series
TABLE OF CONTENTS
Standard & Optional Equipment ......................................................................3
Model Features/Physical Data & Specifications..................................................4
Model Number Identification ............................................................................5
Dimensional Data ........................................................................................6-7
Blower Performance Data ................................................................................8
Accessories....................................................................................................9
Limited Warranty ..........................................................................................10
2
Air
Standard & Optional Equipment
R801P (UF/HZ) Series
PATENTED HEAT EXCHANGER
DRAFT INDUCER MOTOR
IN-SHOT BURNERS
DIRECT SPARK IGNITOR
INTEGRATED
FURNACE
CONTROL
STANDARD EQUIPMENT
OPTIONAL EQUIPMENT
Completely assembled and wired; induced draft; pressure switch;
redundant main gas control; blower compartment door safety switch;
solid state time on/time off blower control; limit control; manual shutoff valve, pressure regulator for natural and L.P. (propane) gas;
transformer; direct drive multi-speed blower motor. Furnaces are
equipped with cooling/heating relay and transformer (40VA) ready for
air conditioning applications. (Please note: a thermostat is not
included as standard equipment.) Flame sensor diagnostics.
Side and bottom filter frame assembly. Return air cabinet for all sizes.
NOTE: Furnace is not listed for use with fuels other than natural or L.P.
(propane) gas.
The complete terms of limited and other warranties are available at our
sales office, or through local installer.
All models can be converted by a qualified Rheem distributor or local
service dealer to use L.P. (propane) gas without changing burners.
Factory approved kits must be used to convert from natural to L.P.
(propane) gas and may be ordered as optional accessories from a
Rheem parts distributor.
For L.P. (propane) operation, refer to Conversion Kit Index Form.
NOTE: For natural and L.P. (propane) gas models, direct spark ignition
is 100% safety lockout type.
WARNING
THIS FURNACE IS NOT APPROVED
OR RECOMMENDED
FOR USE IN MOBILE HOMES
3
Air
Model Features/Physical Data & Specifications
R801P (UF/HZ) Series
Model Features
• Low profile 34" cabinet ideal for space constrained
installations
• Blower shelf design serviceable in all furnace orientations
• Hemmed edges on cabinets and doors
• 1/4 turn door knobs for tool less access
• Integrated Controls board features dip switches for easy
system set up
• QR code for quick access to product information from your
smart phone or tablet
80% residential Gas Furnace CSA certified
3 way multi poise design UF / HZ
PlusOne™ Diagnostics — 7 Segment LED all units
PlusOne™ Ignition System – DSI for reliability and longevity
Heat exchanger is removable for improved serviceability.
Aluminized steel construction provides maximum corrosion
resistance and thermal fatigue reliability.
• Solid doors provide quiet operation
• Solid bottom
• Insulated blower compartment
•
•
•
•
•
Physical Data and Specifications
MODEL NUMBERS R801P SERIES
R801PA050314M*A
R801PA075417M*A
R801PA100521M*A
R801PA125524M*A
R801PA150524M*A
Input-BTU/Hr [kW] ➁
Heating Capacity BTU/Hr [kW] ➀
Heat Ext. Static Pressure [kPa]
50,000 [15]
40,000 [12]
.10 [.025]
75,000 [22]
60,000 [18]
.12 [.029]
100,000 [29]
80,000 [23]
.15 [.037]
125,000 [37]
100,000 [29]
.20 [.05]
150,000 [44]
120,000 [32]
.20 [.05]
Blower (D x W) [mm]
11 x 6
[279 x 152]
11 x 7
[279 x 178]
11 x 10
[279 x 254]
11 x 10
[279 x 254]
11 x 10
[279 x 254]
Motor H.P.–Speed–
PSC Type [W]
1/3-4-PSC
1/2-4-PSC
1/2-4-PSC
3/4-4-PSC
3/4-4-PSC
[248]
[373]
[373]
[560]
[560]
Motor Full Load Amps
Heating Speed
Cooling Speed
5.7
Med-Low
High
7.8
Med-High
Med-Low
7.5
Med-Low
High
8.4
Med-High
High
9.3
Med-High
High
Cooling CFM @ Rating Point
[L/s]
1250
[590]
1200
[566]
1800
[850]
1750
[825]
1900
[900]
Max. E.S.P. (In. W.C.) [kPa]
0.8 [.20]
0.8 [.20]
0.8 [.20]
0.8 [.20]
0.8 [.20]
Temperature Rise Range °F
[°C]
25-55
[13.9-30.6]
25-55
[13.9-30.6]
35-65
[19.4-36.1]
35-65
[19.4-36.1]
45-75
[25-41.7]
155
[68.3]
155
[68.3]
180
[82.2]
165
[73.8]
190
[87.7]
85
[39]
105
[48]
115
[52]
140
[63]
150
[68]
80.0%
80.0%
80.0%
80.0%
Max. Outlet Air Temp. °F
[°C]
Approx. Shipping Weight (Lbs.)
[kg]
AFUE ➀
80.0%
NOTES: All models are 115V, 60HZ, 1 Ph. Gas connection size for all models is
➀ In accordance with D.O.E. test procedures.
➁ See Conversion Kit Index Form for high altitude derate.
* S = Standard, X = Low Nox
[ ] Designates Metric Conversions
4
1/2"
[12 mm] N.P.T.
Air
Model Number Identification
R801P (UF/HZ) Series
Model Number Identification
R
80
Rheem
80 =
80% AFUE
1
P
A
1 = Single Stage P = Premium Design Series
PSC
A = 1st Design
075
4
17
M
S
A
Input
BTU/HR [kW]
050 = 50,000 [15]
075 = 75,000 [22]
100 = 100,000 [29]
125 = 125,000 [37]
150 = 150,000 [44]
3 = Up to
3 Ton
4 = 21/2 to
4 Ton
5 = 31/2 to
5 Ton
Cabinet
Width
14 = 14".0
17 = 17.5"
21 = 21".0
24 = 24.5"
M = Multi
X = Low NOx
S = Standard
RevisionMarketing
(A – First Time
Release)
[ ] Designates Metric Conversions
5
Air
Dimensional Data
R801P (UF/HZ) Series
Upflow Application
Dimensional Data: Upflow Model
MODEL
R801P-
A
B
C
D
E
F
LEFT
SIDE
050
075
100
125
150
141/2 [356]
171/2 [445]
211/2 [533]
241/2 [622]
241/2 [622]
1227/32 [326]
1611/32 [415]
1927/32 [504]
2311/32 [593]
2311/32 [593]
105/8 [270]
123/8 [314]
141/8 [359]
157/8 [403]
157/8 [403]
➀
➀
➀
➀
➀
111/2 [292]
151/2 [381]
181/2 [470]
221/2 [559]
221/2 [559]
17/8 [48]
21/2 [64]
21/2 [64]
21/2 [64]
21/2 [64]
0
0
0
0
0
REDUCED CLEARANCE (IN.) [mm]
RIGHT
BACK
TOP
FRONT
SIDE
4 [102] ➁
0
1 [25]
3 [76]
3 [76] ➁
0
1 [25]
3 [76]
0
0
0
0
0
0
1 [25]
1 [25]
1 [25]
3 [76]
3 [76]
3 [76]
VENT
SHIP
WGTS.
(LBS.) [kg]
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
85 [38.6]
105 [47.6]
120 [54.4]
140 [63.5]
150 [68] .
NOTES: ➀ May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter. 4" adapter included with (-)801P units.
➁ May be 0" [0 mm] with type B vent.
➂ May be 1" [25 mm] with type B vent.
Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with
local codes.
[ ] Designates Metric Conversions
6
Air
Dimensional Data
R801P (UF/HZ) Series
Horizontal Application
WARNING
THIS FURNACE IS NOT APPROVED
OR RECOMMENDED FOR INSTALLATION
ON ITS BACK, WITH ACCESS DOORS
FACING UPWARDS.
Dimensional Data: Horizontal Model
MODEL
R801P-
A
B
C
D
E
F
LEFT
SIDE
050
075
100
125
150
141/2 [356]
171/2 [445]
211/2 [533]
241/2 [622]
241/2 [622]
1227/32 [326]
1611/32 [415]
1927/32 [504]
2311/32 [593]
2311/32 [593]
105/8 [270]
123/8 [314]
141/8 [359]
157/8 [403]
157/8 [403]
➀
➀
➀
➀
➀
111/2 [292]
151/2 [381]
181/2 [470]
221/2 [559]
221/2 [559]
17/8 [48]
21/2 [64]
21/2 [64]
21/2 [64]
21/2 [64]
0
0
0
0
0
REDUCED CLEARANCE (IN.) [mm]
RIGHT
BACK
TOP
FRONT
SIDE
4 [102] ➁
0
1 [25]
3 [76]
3 [76] ➁
0
1 [25]
3 [76]
0
0
0
0
0
0
1 [25]
1 [25]
1 [25]
3 [76]
3 [76]
3 [76]
VENT
SHIP
WGTS.
(LBS.) [kg]
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
6 [152] ➂
85 [38.6]
105 [47.6]
120 [54.4]
140 [63.5]
150 [68] .
NOTES: ➀ May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter. 4" adapter included with (-)801P units.
➁ May be 0" [0 mm] with type B vent.
➂ May be 1" [25 mm] with type B vent.
Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with
local codes.
[ ] Designates Metric Conversions
7
Air
Blower Performance Data
R801P (UF/HZ) Series
Blower Performance Data
MODEL
MOTOR H.P. [W]
BLOWER SIZE
IN [mm]
(-)801PA050314M*A
1/3 [249]
11 x 6
[279 x 152]
(-)801PA075417M*A
1/2 [373]
11 x 7
[279 x 178]
(-)801PA100521M*A
1/2 [373]
11 x 10
[279 x 254]
(-)801PA125524M*A
3/4 [559]
11 x 10
[279 x 254]
(-)801PA150524M*A
3/4 [559]
11 x 10
[279 x 254]
Note: Bold data is factory heating tap.
[ ] Designates Metric Conversions
8
CFM [L/s] AIR DELIVERY
EXTERNAL STATIC PRESSURE INCHES WATER COLUMN [kPa]
SPEED
TAP
Low
Med. Lo
Med. Hi
High
Low
Med. Lo
Med. Hi
High
Low
Med. Lo
Med. Hi
High
Low
Med. Lo
Med. Hi
High
Low
Med. Lo
Med. Hi
High
0.1 [.02]
823
1030
1129
1361
1229
1308
1553
1969
1209
1438
1902
2071
1358
1541
1799
2015
1411
1606
1889
2178
0.2 [.05]
803
1018
1132
1353
1200
1267
1542
1924
1182
1420
1883
2037
1354
1517
1774
1989
1395
1579
1891
2160
0.3 [.07]
787
1006
1112
1331
1181
1266
1516
1893
1131
1386
1844
2001
1331
1476
1746
1929
1370
1569
1849
2105
0.4 [.10]
732
976
1087
1297
1155
1233
1491
1840
1112
1350
1817
1962
1301
1453
1712
1902
1334
1537
1828
2067
0.5 [.12]
718
929
1054
1264
1120
1204
1451
1803
1051
1320
1753
1905
1250
1416
1691
1862
1310
1499
1764
2024
0.6 [.15]
691
897
1028
1232
1078
1176
1417
1728
976
1293
1700
1856
1224
1371
1629
1815
1252
1468
1717
1976
0.7 [.17]
651
850
971
1164
1013
1113
1358
1657
929
1248
1636
1807
1154
1339
1554
1742
1220
1407
1659
1916
0.8 [.19]
593
808
919
1117
970
1062
1306
1570
867
1186
1547
1709
1089
1277
1495
1665
1150
1346
1609
1832
Air
SIDE RETURN FILTER RACK: RXGF-CD
BOTTOM RETURN FILTER RACK FOR
UPFLOW APPLICATION: RXGF-CB
WARNING: IMPORTANT NOTICE
FILTER RACK FILTER SIZES* INCHES [mm]
MODEL
RXGF-CB
(UPFLOW/
HORIZONTAL)
RXGF-CD
(UPFLOW)
SIDE RETURN
R801PA050
121/4 x 25
[311 x 635]
153/4 x 25
[400 x 635]
R801PA075
153/4 x 25
[400 x 635]
153/4 x 25
[400 x 635]
R801PA100
191/4 x 25
[489 x 635]
153/4 x 25
[400 x 635]
R801PA125
223/4 x 25
[578 x 635]
153/4 x 25
[400 x 635]
R801PA150
223/4 x 25
[578 x 635]
153/4 x 25
[400 x 635]
INDOOR COIL CASINGS
MODEL
NUMBER
RXBC-D14AI
RXBC-D17AI
RXBC-D21AI
RXBC-D21BI
RXBC-D24AI
4" FLUE ADAPTER: RXGW-C01
Accessories
R801P (UF/HZ) Series
A SOLID METAL BASE PLATE (SEE TABLE) MUST BE IN PLACE WHEN THE
FURNACE IS INSTALLED WITH SIDE AIR RETURN DUCTS. FAILURE TO
INSTALL A BASE PLATE COULD CAUSE PRODUCTS OF COMBUSTION TO
BE CIRCULATED INTO THE LIVING SPACE AND CREATE POTENTIALLY
HAZARDOUS CONDITIONS.
FURNACE
WIDTH
IN. [mm]
141/2 [356]
171/2 [445]
211/2 [533]
241/2 [622]
SOLID
BOTTOM
KIT NO.
RXGB-D14
RXGB-D17
RXGB-D21
RXGB-D24
BASE
PLATE NO.
AE-61874-01
AE-61874-02
AE-61874-03
AE-61874-04
BASE
PLATE SIZE
IN. [mm]
115/8 x 239/16 [295 x 598]
151/8 x 239/16 [384 x 598]
185/8 x 239/16 [473 x 598]
255/8 x 239/16 [651 x 598]
FOR HIGH ALTITUDES:
OPTION CODE FOR HIGH ALTITUDE: U.S. & Canada
None required for high altitudes.
HIGH ALTITUDE CONVERSION KITS: U.S. & Canada
None required for high altitudes.
80+ HIGH ALTITUDE INSTRUCTIONS
CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines
when converting for high altitudes.
High altitude option codes are not required for these models.
However, the burner orifice size needs to be recalculated and verified
at elevations above 2000 ft. See Installation Instructions for more
information.
NOTE: For Canadian installations only, an optional derate (manifold
gas pressure reduction) method may be used to adjust the
furnace for altitude. See Installation Instructions for more
information. This optional method may NOT be used for U.S.
installations.
[ ] Designates Metric Conversions
9
Air
Limited Warranty
R801P (UF/HZ) Series
GENERAL TERMS OF LIMITED WARRANTY*
Rheem will furnish a replacement for any part of this product
which fails in normal use and service within the applicable
period stated, in accordance with the terms of the limited
warranty.
*For complete details of the Limited and Conditional Warranties,
including applicable terms and conditions, contact your local contractor
or the Manufacturer for a copy of the product warranty certificate.
10
Conditional Parts* (Registration Required) ......Ten (10) Years
Heat Exchanger ......................................Twenty (20) Years
Air
Notes
R801P (UF/HZ) Series
11
The new degree of comfort.™
In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.
Rheem Heating, Cooling & Water Heating • P.O. Box 17010
Fort Smith, Arkansas 72917 • www.rheem.com
Rheem Canada Ltd./Ltée • 125 Edgeware Road, Unit 1
Brampton, Ontario • L6Y 0P5
PRINTED IN U.S.A. 1/15 QG FORM NO. G11-543 REV. 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising